Characterization of a multi-metal binding biosorbent: Chemical modification and desorption studies

Removal of Aflatoxin B1 Using Alfalfa Leaves as an Adsorbent Material: A Comparison between Two In Vitro Experimental Models

An adsorbent material derived from alfalfa leaves was prepared and further characterized, and its efficacy for removing aflatoxin B1 (AFB1) was investigated. Characterization consisted of the use of attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), environmental scanning electron microscopy (ESEM), X-ray fluorescence spectroscopy (XRF), X-ray diffraction (XRD), point of zero charge (pHpzc), zeta potential (ζ-potential), UV-Vis diffuse reflectance spectroscopy, and spectral analysis. To determine the adsorption capacity against AFB1 (250 ng AFB1/mL), pH-dependent and avian intestinal in vitro models were used. The adsorbent inclusion percentage was 0.5% (w/w). In general, the pH-dependent model gave adsorption percentages of 98.2%, 99.9%, and 98.2%, evaluated at pH values of 2, 5, and 7, respectively. However, when the avian intestinal model was used, it was observed that the adsorption percentage of AFB1 significantly decreased (88.8%). Based on the characterization results, it is proposed that electrostatic, non-electrostatic, and the formation of chlorophyll-AFB1 complexes were the main mechanisms for AFB1 adsorption. From these results, it can be concluded that the adsorbent derived from alfalfa leaves could be used as an effective material for removing AFB1 in in vitro digestion models that mimic the physiological reality.

Plants, animals, and fisheries waste-mediated bioremediation of contaminants of environmental and emerging concern (CEECs)-a circular bioresource utilization approach

The release of contaminants of environmental concern including heavy metals and metalloids, and contaminants of emerging concern including organic micropollutants from processing industries, pharmaceuticals, personal care, and anthropogenic sources, is a growing threat worldwide. Mitigating inorganic and organic contaminants, which can be coined as contaminants of environmental and emerging concern (CEECs), is a big challenge as traditional physicochemical processes are not economically viable for managing mixed contaminants of low concentrations. As a result, low-cost materials must be designed to provide high CEEC removal efficiency. One of the environmentally viable and energy-efficient approaches is biosorption, which involves using biomass or biopolymers isolated from plants or animals to decontaminate heavy metals in contaminated environments using inherent biological mechanisms. Among chemical constituents in plant biomass, cellulose, lignin, hemicellulose, proteins, polysaccharides, phenolic compounds, and animal biomass include polysaccharides and other compounds to bind heavy metals covalently and non-covalently. These functional groups include carboxyl, hydroxyl, carbonyl, amide, amine, and sulfhydryl. Cation-exchange capacities of these bioadsorbents can be improved by applying chemical modifications. The relevance of chemical constituents and bioactives in biosorbents derived from agricultural production such as food and fodder crops, bioenergy and cash crops, fruit and vegetable crops, medicinal and aromatic plants, plantation trees, aquatic and terrestrial weeds, and animal production such as dairy, goatery, poultry, duckery, and fisheries is highlighted in this comprehensive review for sequestering and bioremediation of CEECs, including as many as ten different heavy metals and metalloids co-contaminated with other organic micropollutants in circular bioresource utilization and one-health concepts.

Valorization of lignocellulosic biomass into sustainable materials for adsorption and photocatalytic applications in water and air remediation

An exponential rise in global pollution and industrialization has led to significant economic and environmental problems due to the insufficient application of green technology for the chemical industry and energy production. Nowadays, the scientific and environmental/industrial communities push to apply new sustainable ways and/or materials for energy/environmental applications through the so-called circular (bio)economy. One of today's hottest topics is primarily valorizing available lignocellulosic biomass wastes into valuable materials for energy or environmentally related applications. This review aims to discuss, from both the chemistry and mechanistic points of view, the recent finding reported on the valorization of biomass wastes into valuable carbon materials. The sorption mechanisms using carbon materials prepared from biomass wastes by emphasizing the relationship between the synthesis route or/and surface modification and the retention performance were discussed towards the removal of organic and heavy metal pollutants from water or air (NO_x, CO₂, VOCs, SO₂, and Hg⁰). Photocatalytic nanoparticle-coated biomass-based carbon materials have proved to be successful composites for water remediation. The review discusses and simplifies the most raised interfacial, photonic, and physical mechanisms that might take place on the surface of these composites under light irradiation. Finally, the review examines the economic benefits and circular bioeconomy and the challenges of transferring this technology to more comprehensive applications.

Desorption of zinc, copper and lead ions from loaded flax fibres

Biosorption is an efficient and cost-effective method for heavy metals' remediation. However, saturated biosorbents may pose a serious problem for the environment. Flax fibres have shown very good adsorption capacities to remove zinc, copper and lead ions from contaminated aqueous solutions. In this study, adsorption-desorption cycles were conducted with loaded flax fibres in batch mode to recover heavy metals using four types of solutions: hydrochloric acid solution, nitric acid solution, sodium hydroxide solution and ultrapure water. Desorption kinetic studies, conducted with loaded flax fibres, showed very fast desorption of zinc, copper and lead when using nitric and hydrochloric acids with a selectivity sequence of Zn (totally desorbed) > Cu (94%) > Pb (80-73%). Desorption kinetic was slower with the use of sodium hydroxide and showed much lower desorption rates of Zn (62%) > Pb (12%) > Cu (7%). Desorption of zinc and copper from previously loaded fibres from binary metal ion system in lead solution was also investigated. Different concentrations ranging from 0.04 to 0.20 mmol/L were tested. The obtained results demonstrated a significant release in the order Zn (18-90%) > Cu (2-42%), while lead was still efficiently adsorbed. Retention efficiencies of zinc and copper and adsorption efficiency of lead resulted in the same adsorption efficiencies of the three metal ions onto flax fibres in the ternary metal ion system.

Investigation of cadmium and nickel biosorption by Pseudomonas sp. via response surface methodology

The environmental contamination of heavy metals has grown over the last several decades along with global industrialization and now constitutes a serious threat to human health. In this research, high cadmium (Cd) and nickel (Ni) resistant bacteria that were chosen for heavy metal biosorption were isolated from the Industries Factory in Sari, Mazandaran, Iran. Pseudomonas aeruginosa was recognized as the isolated bacterium based on its morphological, physiological, biochemical, antibiotic resistance testing, and 16S rRNA sequences. The bacteria had the highest concentrations of resistance to Cd (up to 1600 ppm) and Ni, according to the Minimum Inhibition Concentration (MIC) test (up to 2000 ppm). Single-factor studies in single and binary systems were used to examine the effects of temperature, contact duration, pH value, starting Cd and Ni concentration, and biomass dose on the Cd and Ni adsorption by P. aeruginosa. The Cd and Ni biosorption in binary solutions was optimized using the response surface methodology (RSM) based on Central Composite Design (CCD). The investigation revealed that at pH 7.0, 45 °C, and 1.5 gL^-1 biomass dose, the greatest biosorption efficiency for Cd and Ni was 92.43 percent and 88.45 percent, respectively. According to the adsorption of Cd and Ni in urban water, under these similarly extreme conditions, Cd adsorption drops to 54% and Ni to 60%. Analysis Potential functional groups involving interactions between cells and metal ions were identified using Fourier transform infrared spectroscopy (FTIR). Different compounds and heavy metal ions were found to have been adsorbed to the surface of the biosorbent by scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM/EDS). It was determined that P. aeruginosa had a high rate of Cd and Ni adsorption and that variations in pH level had a greater impact than other parameters. The findings imply that P. aeruginosa biomass may be an effective, economical, and environmentally friendly method for removing Cd and Ni from contaminated settings. It also has a reasonable capacity for biosorption in both a natural environment and a laboratory environment.

Rare earths stick to rare cyanobacteria: Future potential for bioremediation and recovery of rare earth elements

Biosorption of metal ions by phototrophic microorganisms is regarded as a sustainable and alternative method for bioremediation and metal recovery. In this study, 12 cyanobacterial strains, including 7 terrestrial and 5 aquatic cyanobacteria, covering a broad phylogenetic diversity were investigated for their potential application in the enrichment of rare earth elements through biosorption. A screening for the maximum adsorption capacity of cerium, neodymium, terbium, and lanthanum was conducted in which Nostoc sp. 20.02 showed the highest adsorption capacity with 84.2-91.5 mg g^-1. Additionally, Synechococcus elongatus UTEX 2973, Calothrix brevissima SAG 34.79, Desmonostoc muscorum 90.03, and Komarekiella sp. 89.12 were promising candidate strains, with maximum adsorption capacities of 69.5-83.4 mg g^-1, 68.6-83.5 mg g^-1, 44.7-70.6 mg g^-1, and 47.2-67.1 mg g^-1 respectively. Experiments with cerium on adsorption properties of the five highest metal adsorbing strains displayed fast adsorption kinetics and a strong influence of the pH value on metal uptake, with an optimum at pH 5 to 6. Studies on binding specificity with mixed-metal solutions strongly indicated an ion-exchange mechanism in which Na⁺, K⁺, Mg²⁺, and Ca²⁺ ions are replaced by other metal cations during the biosorption process. Depending on the cyanobacterial strain, FT-IR analysis indicated the involvement different functional groups like hydroxyl and carboxyl groups during the adsorption process. Overall, the application of cyanobacteria as biosorbent in bioremediation and recovery of rare earth elements is a promising method for the development of an industrial process and has to be further optimized and adjusted regarding metal-containing wastewater and adsorption efficiency by cyanobacterial biomass.

Biosorption of hexavalent chromium from aqueous solution by pristine and CaCl2-modified erythromycin production residues

In this study, the adsorptive removal of hexavalent chromium [Cr(VI)] from aqueous solutions by the pristine and salt-treated (CaCl₂) erythromycin production residue (EPRs and SEPRs) were investigated. Batch experiments were carried out to determine the effect of contact time, sorbent dosage, pH, initial Cr concentration, and temperature on Cr(VI) sorption by EPRs and SEPRs. The highest adsorptive removal capacities were achieved at the pH equal to 1.0, and the maximum adsorption capacities for EPRs and SEPRs at optimized conditions were 21.74 and 35.24 mg g^-1, respectively. The FTIR spectra and SEM studies were examined for the pristine adsorbent and after the adsorption of Cr(VI). Moreover, thermodynamic results indicated that Cr sorption by EPR/SERPs was feasible, spontaneous, and endothermic under the optimum conditions. Langmuir model fitted well with the experimental data. Kinetic modeling revealed that the biosorption of Cr(VI) by EPRs and SEPRs obeyed the second-order model than the first-order model. The process involving rate-controlling step is much complex involving both boundary layer and intra-particle diffusion processes. Furthermore, the adsorption-coupled-reduction process was believed as the main mechanism of Cr(VI) removal by EPRs and SEPRs. In summary, both adsorbents could be considered as promising low-cost biosorbent for the removal of Cr(VI) from aqueous systems.

Potential application of spent mushroom compost (SMC) biochar as low-cost filtration media in heavy metal removal from abandoned mining water: a review

Overpopulation and rapid development have put an increasing burden on the environment, leading to various water crisis. Importing water from abandoned mines as an alternative raw water source could be the next answer to alleviate water scarcity problems globally. However, due to its high heavy metals content, there is a need to find an economical and effective method to remove heavy metals before reusing it as potable water source. Biochar, a low-cost and carbon-rich biosorbent, has received increasing attention on its application as a remediating agent to remove heavy metals from water. Previous studies have revealed the potential properties of biochar as a heavy metal removal agent including high cation exchange capacity, high surface area, active surface functional groups, as well as efficient adsorption. Apparently, the most important factor influencing the sorption mechanism is the type of feedstock materials. Spent mushroom compost (SMC), a waste product from mushroom cultivation, has been found as an excellent biosorbent. SMC has received global attention as it is low cost and eco-friendly. It also has been proved as an efficient heavy metals remover from water. Nevertheless, its application as biochar is still scarce. Therefore, this review focuses on the potential of transforming SMC into modified biochar to remove heavy metals, especially from abandoned mining water. The present review emphasizes the current trends in adsorption methods for heavy metal removal from water, assembles data from previous studies on the feedstock of biosorbents to biochars, and discusses the potentials of SMC as a biochar for water treatment.

Polyethyleneimine modified activated carbon for high-efficiency adsorption of copper ion from simulated wastewater

In this study, activated carbon (AC) was chemically activated using sodium hydroxide (NaOH), and polyethyleneimine (PEI) was grafted onto the AC using glutaraldehyde as a cross-linking agent. Then the modified AC was applied to treat water samples containing copper ions (Cu²⁺). Preparation of AC-NaOH@PEI. The grafted AC was characterized, demonstrating that the specific surface area of material decreased from 959.3 to 556.9 m²/g. The ζ-potential changed from -27.2 to 10.4 mV, and the presence of a distinct flocculation on the surface of the AC was observed via scanning electron microscopy. The results demonstrated that PEI was successfully grafted onto the surface of AC. Furthermore, the adsorption results indicated that the Cu²⁺ adsorption capacity of AC-NaOH@PEI was greatly enhanced with increasing PEI loading. The adsorption amount of Cu²⁺ by the grafted AC-NaOH@PEI-200 increased from 20.02 to 47.8 mg/g. In addition, the adsorption of Cu²⁺ by AC-NaOH@PEI was a pH dependent process. At a pH of 6, the maximum removal rate reached 93%. The adsorption process is better described by the Langmuir and quasi-second order adsorption models, signifying that the adsorption of Cu²⁺ on AC@PEI consists of monolayer adsorption and chemisorption. After four adsorption-desorption cycles, AC@PEI exhibited high adsorption capacity for Cu²⁺, indicating that it has good regeneration ability. It is a promising adsorbent material.

Recovering rare earth elements via immobilized red algae from ammonium-rich wastewater

Biotreatment of acidic rare earth mining wastewater via acidophilic living organisms is a promising approach owing to their high tolerance to high concentrations of rare earth elements (REEs); however, simultaneous removal of both REEs and ammonium is generally hindered since most acidophilic organisms are positively charged. Accordingly, immobilization of acidophilic Galdieria sulphuraria (G. sulphuraria) by calcium alginate to improve its affinity to positively charged REEs has been used for simultaneous bioremoval of REEs and ammonium. The results indicate that 97.19%, 96.19%, and 98.87% of La, Y, and Sm, respectively, are removed by G. sulphuraria beads (GS-BDs). The adsorption of REEs by calcium alginate beads (BDs) and GS-BDs is well fitted by both pseudo first-order (PFO) and pseudo second-order (PSO) kinetic models, implying that adsorption of REEs involves both physical adsorption caused by affinity of functional groups such as -COO- and -OH and chemical adsorption based on ion exchange of Ca²⁺ with REEs. Notably, GS-BDs exhibit high tolerance to La, Y, and Sm with maximum removal efficiencies of 97.9%, 96.6%, and 99.1%, respectively. Furthermore, the ammonium removal efficiency of GS-BDs is higher than that of free G. sulphuraria cells at an initial ammonium concentration of 100 mg L^-1, while the efficiency decreases when initial concentration of ammonium is higher than 150 mg L^-1. Last, small size of GS-BDs favors ammonium removal because of their lower mass transfer resistance. This study achieves simultaneous removal of REEs and ammonium from acidic mining drainage, providing a potential strategy for biotreatment of REE tailing wastewater.

Fabrication of alginate@silver nanoparticles (Alg@AgNPs) bionanocomposite for the sequestration of crystal violet dye from aqueous solution

In the present study, alginate@silver nanoparticles (Alg@AgNPs) bionanocomposite has been fabricated successfully and further explored for the removal of crystal violet (CV) dye from the aqueous solution. The surface morphology of the (Alg@AgNPs) bionanocomposite was characterized by various modern analytical techniques such as SEM-EDX, TEM, FTIR and XRD. The maximum adsorption was observed at optimum condition of (pH 7, adsorbent dose 0.01 g, equilibrium time 240 min and initial concentration 20 mg L^-1). The maximum monolayer adsorption capacity was found to be 186.93 mg g^-1 at 30 °C. The experimental data were further validated by various isotherm models and on the basis of highest correlation coefficient (R², 0.99), Langmuir model was found to be best fitted model. Pseudo-second order kinetic model obeyed best for the experimental data with a highest correlation coefficient (R², 0.99) at all studied temperature. In thermodynamic studies, the positive value of enthalpy change (∆H⁰) and entropy change (∆S⁰) confirmed the process to be endothermic and spontaneous in nature. Desorption studies shows that 83 % of the adsorbed CV can be desorbed in first cycle and can be regenerated up to 4th cycle effectively with 0.1 M HCl. Therefore, (Alg@AgNPs) bionanocomposite could be harnessed as a potential adsorbent for the removal of hazardous CV dye from the waste water.

Lignocellulosic Materials Used as Biosorbents for the Capture of Nickel (II) in Aqueous Solution

Four lignocellulosic materials (walnut shell, chestnut shell, pine wood and burnt pine wood) were analyzed as biosorbents to remove nickel ions in aqueous solution. The optimal pH condition was determined. Due to this, a range of different pHs (3.0 to 7.5) was tested. The adsorption isotherms and kinetics were established. To plot Langmuir and Freundlich isotherms, batch adsorption tests were made with variable nickel concentrations (5 to 200 mg L−1). The pseudo-first order, pseudo-second order, Elovich and intraparticle diffusion models were used to describe the kinetics, batch adsorption tests were carried out with 25 mg L−1 of nickel solution and agitation time varied from 10 to 1440 min. The specific surface area of the different materials was between 3.97 and 4.85 m2g−1 with the exception for wood with 1.74 m2g−1. The pore size was 26.54 nm for wood and varied between 5.40 and 7.33 nm for the remaining materials. The diffractograms analysis showed that all the lignocellulosic materials presented some crystalline domains with the exception of burnt pine wood which was completely amorphous. The best pH was found to be around 5.0. At this pH the adsorption was higher for chestnut shells, walnut shells, burnt pine wood and wood, respectively. All samples fitted the Langmuir model well, with R2 of 0.994 to 0.998. The sorption kinetics was well described by the pseudo-second order equation with R2 between 0.996 and 1.00. No significative differences on the surface of the materials before and after adsorption could be observed by SEM. Finally, all materials tested were able to remove nickel ions in aqueous solution.

Towards a Circular Economy: Analysis of the Use of Biowaste as Biosorbent for the Removal of Heavy Metals

Industrial human activity has led to the release of substantial amounts of heavy metals into the environment. Contamination of water with heavy metals such as lead, cadmium, copper, zinc, chromium, or nickel represents a serious problem. As part of the circular economy, it is appropriate to use biowaste from agriculture, fisheries, and the timber industry as biosorbents. In this literature review, the potential of using these biowaste groups as biosorbents for metal removal is presented. This biowaste is characterized by the presence of carboxyl, hydroxyl, carbonyl, amide, amine, sulfydryl, and other groups on their surface, which form complexes and chelates with metals present in water. Biosorption seems to be a potential alternative to conventional technologies for removing or recovering heavy metals from water or wastewater, which are uneconomical and generate additional waste. The paper demonstrates that harnessing the potential of biowaste to remove metals is beneficial to the environment as they can solve the problem of incineration and realise recycling that meets the circular economy. Although the choice of a suitable biosorbent for the removal of a particular metal involves a lot of research, the high biosorption efficiency, low cost, and renewability justify their use.

Nanomodified sugarcane bagasse biosorbent: synthesis, characterization, and application for Cu(II) removal from aqueous medium

Biosorption is a technique widely used in the remediation of contaminated effluents, and its main advantages are its easy applicability, high efficiency rate, versatility, and its economic viability. Associated with nanotechnology, this work proposes the use of nanocomposites of sugarcane bagasse (SB) and ferromagnetic nanoparticles (Fe₃O₄) in the removal of metallic ions present in contaminated water. SB is a promising adsorbent material since it is an abundant agricultural residue, easily accessed. By using the coprecipitation method, two nanocomposites were obtained from in natura (SB-NP) or acid-treated (MSB-NP) sugarcane bagasse. These materials were synthetized by impregnation of Fe₃O₄ to gain paramagnetic properties and to facilitate the removal of the contaminant-containing adsorbent. The characterization of the nanocomposites was performed using pH_PCZ, FTIR, XRD, and SEM/EDS techniques, to evaluate the synthesis efficiency and investigate the morphology of the materials. The efficiency of magnetite impregnation on the SB was assessed by SEM/EDS and XRD, while the main functional groups (carbonyl, carboxyl, hydroxyl, amine, amide, and nitrate) responsible for adsorption were found by FTIR. In the surface charge characterization by pH_PCZ sorption of dyes, it was found that negative charges are predominant. The pH_PCZ for SB-NP and MSB-NP was 5.95 and 5.59, respectively, and the chosen Cu(II) adsorption pH was 6.2 ± 0.1. The adsorption equilibrium was reached between 10 and 60 min of contact time. The maximum experimental sorption capacity (SC_exp) was 2.53 ± 0.09 (SB-NP) and 2.61 ± 0.01 mg/g (MSB-NP). The isotherm models applied to the experimental data were Langmuir, Freundlich, Sips, Temkin, and Dubinin-Radushkevich, and Temkin best described the adsorption phenomena for Cu(II) by SB-NP (r² = 0.9976 and χ² = 3.965) and MSB-NP (r² = 0.9990 and χ² = 1.816). Reuse cycles of the nanocomposites were also performed employing ten cycles of sorption using 50 mg/L Cu(II) solutions, after which the materials showed SC_exp = 7.47 ± 0.04 mg/g (SB-NP) and 7.82 ± 0.04 mg/g (MSB-NP). Therefore, the investigated materials exhibited promising results to be used as biosorbents in the remediation of effluents contaminated with toxic metal ions, such as copper.

Esterification of sugarcane bagasse by citric acid for Pb2+ adsorption: effect of different chemical pretreatment methods

In this study, different pretreatment strategies of sugarcane bagasse prior to citric acid modification were investigated in terms of Pb²⁺ adsorption capacity. Pretreatment strategies included the use of NaOH, HCl, and C₂H₅OH in various concentrations. In order to fundamentally understand how these pretreatment methods affect the modification of sugarcane bagasse by citric acid as well as the Pb²⁺ adsorption capacity of sugarcane bagasse, three main components of sugarcane bagasse namely cellulose, hemicellulose, and lignin were isolated and esterified by citric acid under the same conditions. ATR-FTIR, XPS, SEM, and an analysis of the number of carboxylic acid groups were used to investigate the physicochemical and chemical properties of the materials. These three components were proved to participate in adsorption and induce the esterification with citric acid. Hence, pretreatment with ethanol and 0.01 M NaOH which could retain cellulose, hemicellulose, and lignin in sugarcane bagasse achieved a high Pb²⁺ adsorption capacity, i.e., 122.4 and 97 mg/g after the esterification with citric acid. In contrast, pretreatment with 0.5 M NaOH and 0.1 M HCl removed lignin and hemicellulose, leading to the lowest value of approximately 45 mg/g for citric acid esterified-pretreated sugarcane bagasse. XPS analysis and number of carboxylic group measurement confirmed the esterification between bagasse and citric acid. To understand the adsorption mechanism of adsorbent, two kinetic models including pseudo-first-order model and pseudo-second-order model were applied. The experimental data were well described by the pseudo-second-order model. The adsorption isotherm data were fitted Langmuir and Freundlich.

Heavy metals biosorption mechanism of partially delignified products derived from mango (Mangifera indica) and guava (Psidium guiag) barks

This paper evaluates the biosorption of toxic metal ions onto the bioadsorbents derived from mango (Mangifera indica) and guava (Psidium guiag) barks and their metal fixation mechanisms. Maximum metal biosorption capacities of the mango bioadsorbent were found in the following increasing order (mg/g): Hg (16.24) < Cu (22.24) < Cd (25.86) < Pb (60.85). Maximum metal biosorption capacities of guava bioadsorbent follow similar order (mg/g): Hg (21.48) < Cu (30.36) < Cd (32.54) < Pb (70.25), but with slightly higher adsorption capacities. The removal mechanisms of heavy metals using bioadsorbents have been ascertained by studying their surface properties and functional groups using various spectrometric, spectroscopic, and microscopic methods. Whewellite (C2CaO4·H2O) has been identified in bioadsorbents based on the characterization of their surface properties using X-ray techniques (XPS and XRD), facilitating the ion exchange of metal ions with Ca2+ bonded with carboxylate moieties. For both the bioadsorbents, the Pb2+, Cu2+, and Cd2+ are biosorbed completely by ion exchange with Ca2+ (89-94%) and Mg2+ (7-12%), whereas Hg2+ is biosorbed partially (57-66%) by ion exchange with Ca2+ (38-42%) and Mg2+ (19-24%) due to involvement of other cations in the ion exchange processes. Bioadsorbents contain lignin which act as electron donor and reduced Cr(VI) into Cr(III) (29.87 and 37.25 mg/g) in acidic medium. Anionic Cr(VI) was not adsorbed onto bioadsorbents at higher pH due to their electrostatic repulsion with negatively charged carboxylic functional groups.

Removal of copper and/or zinc ions from synthetic solutions by immobilized, non-viable bacterial biomass: Batch and fixed-bed column lab-scale study

A biosorbent composed of non-viable Pseudomonas putida trapped in agar beads was able to remove Cu²⁺ and Zn²⁺ from solutions containing one or both metals. The process in batch followed pseudo second-order kinetics, with adsorption capacities of 0.255 mg Cu²⁺/g and 0.170 mg Zn²⁺/g according to the Langmuir isotherm. These values were up to ten times lower for beads without biomass. The metals became bound to OH, CH₂, CO, COC and COP groups, with the last three being provided by the biomass, which highlights its importance. Adsorption values for single-metal solutions filtered in a fixed-bed column were 0.152 mg Cu²⁺/g and 0.117 mg Zn²⁺/g, but decreased to 0.075 and 0.058, respectively, with mixed-metal solutions (1:1 ratio). In 10:1-ratio solutions, the metal in greater proportion was better adsorbed. Under all conditions, removal percentage was ∼60 %. The column could be reused throughout ten absorption/desorption cycles without significant alterations in adsorption capacity.

Modified Ziziphus spina-christi stones as green route for the removal of heavy metals

Green routes for remediation of heavy metals are worldwide challenges to overcome pollution problems on one hand and control the adverse impact of chemicals on the other hand. Biosorption is one of the most effective methods for removing lower level of heavy metals. The idea to apply natural resources as a green method for removal of heavy metals, this route has no adverse impacts on the environment. This study investigated the ability of chemically modified Ziziphus spina-christi stones (ZSCs) as agriculture by-products to perform the biosorption of Pb(II), Zn(II) and Cd(II) ions from wastewater in a single and ternary metal system. The characteristic functional groups of chemically modified ZSCs were analyzed by Fourier transform infrared. In comparison with acidic ZSCs, alkali-modified ZSCs by KOH was more effective and enhanced the removal efficiency of ZSCs. Using Langmuir isotherm, the maximum adsorption capacity on the modified ZSCs for Pb(II) was 9.06 mg/g, for Zn(II) obtained by using ZSC-citric acid was 4.19 mg/g and 5.38 mg/g for Cd(II) as obtained by using ZSC-H2O2. The molecular electrostatic potential, which was calculated at B3LYP/6-31G(d,p), indicated that each metal is di-hydrated, forming a complex with two units of amino acids. This mechanism demonstrated the uptake process by ZSCs.

A Biosorption-Pyrolysis Process for Removal of Pb from Aqueous Solution and Subsequent Immobilization of Pb in the Char

The application of biosorption in the removal of heavy metals from water faces a challenge of safe disposal of contaminated biomass. In this study, a potential solution for this problem was proposed by using a biosorption-pyrolysis process featured by pretreatment of biomass with phosphoric acid (PA). The PA pretreatment of biomass increased the removal efficiency of heavy metal Pb from water by sorption, and subsequent pyrolysis helped immobilize Pb in the residual char. The results indicate that most (>95%) of the Pb adsorbed by the PA-pretreated biomass was retained in the char, and that the lower pyrolysis temperature (350 °C) is more favorable for Pb immobilization. In this way, the bioavailable Pb in the char was hardly detected, while the Pb leachable in acidic solution decreased to <3% of total Pb in the char. However, higher pyrolysis temperature (450 °C) is unfavorable for Pb immobilization, as both the leachable and bioavailable Pb increased to >28%. The reason should be related to the formation of elemental Pb and unstable Pb compounds during pyrolysis at 450 °C, according to the X-ray diffraction study.

Environmental impact of lignocellulosic wastes and their effective exploitation as smart carriers - A drive towards greener and eco-friendlier biocatalytic systems

In recent years, lignocellulosic wastes have gathered much attention due to increasing economic, social, environmental apprehensions, global climate change and depleted fossil fuel reserves. The unsuitable management of lignocellulosic materials and related organic wastes poses serious environmental burden and causes pollution. On the other hand, lignocellulosic wastes hold significant economic potential and can be employed as promising catalytic supports because of impressing traits such as surface area, porous structure, and occurrence of many chemical moieties (i.e., carboxyl, amino, thiol, hydroxyl, and phosphate groups). In the current literature, scarce information is available on this important and highly valuable aspect of lignocellulosic wastes as smart carriers for immobilization. Thus, to fulfill this literature gap, herein, an effort has been made to signify the value generation aspects of lignocellulosic wastes. Literature assessment spotlighted that all these waste materials display high potential for immobilizing enzyme because of their low cost, bio-renewable, and sustainable nature. Enzyme immobilization has gained recognition as a highly useful technology to improve enzyme properties such as catalytic stability, performance, and repeatability. The application of carrier-supported biocatalysts has been a theme of considerable research, for the past three decades, in the bio-catalysis field. Nonetheless, the type of support matrix plays a key role in the immobilization process due to its influential impact on the physicochemical characteristics of the as-synthesized biocatalytic system. In the past, an array of various organic, inorganic, and composite materials has been used as carriers to formulate efficient and stable biocatalysts. This review is envisioned to provide recent progress and development on the use of different agricultural wastes (such as coconut fiber, sugarcane bagasse, corn and rice wastes, and Brewers' spent grain) as support materials for enzyme immobilization. In summary, the effective utilization of lignocellulosic wastes to develop multi-functional biocatalysts is not only economical but also reduce environmental problems of unsuitable management of organic wastes and drive up the application of biocatalytic technology in the industry.

Cadmium binding characterization and mechanism of a newly isolated strain Cystobasidium oligophagum QN-3

The aim of this study was to screen a strain for the removal of Cd²⁺ from aqueous solution and investigate the characterization and mechanism of the Cd²⁺ binding process. A novel strain of yeast showed high tolerance of cadmium, namely Cystobasidium oligophagum QN-3, was isolated from soils, which could resist 22,000 mg/L and 18,000 mg/L Cd²⁺ on PDA (potato dextrose agar) plate and in PDA liquid medium, respectively. Cd²⁺ binding experiment showed that the strain could remove Cd²⁺ from aqueous solution effectively, the maximum Cd²⁺ removal rate of 84.45% was achieved at initial Cd²⁺ concentration 30 mg/L. Scanning electron microscopy (SEM) analysis revealed that sorption of Cd²⁺ by cells could be associated with changes in the cell surface morphology. Fourier transform-infrared spectroscopy (FTIR) analysis confirmed the important role of the functional groups OH, CO, NH₂ , COO, PO, and CH on the cell surface in the binding of Cd²⁺ . The comparison of the binding ability of different cellular parts indicated a significant role of the cell wall played in the Cd²⁺ binding process. Pretreatment of the cells by boiling or ultrasonication could improve the biosorption capacity of QN-3. In addition, QN-3 exhibited selective and preferential property of binding capacity for other heavy metals, such as Pb²⁺ , Cu²⁺ , Cd²⁺ , Zn²⁺ , and Ni²⁺ . These data suggested the promising use of Cystobasidium oligophagum QN-3 as an effective and friendly biosorbent for cadmium or other heavy metals decontamination in the environment.

Megamerger of biosorbents and catalytic technologies for the removal of heavy metals from wastewater: Preparation, final disposal, mechanism and influencing factors

Heavy metal pollution, because of its high toxicity, non-biodegradability and biological enrichment, has been identified as a global aquatic ecosystems threat in recent decades. Due to the high efficiency, low cost, satisfactory recyclability, easy storage and separation, biosorbents have exhibited a promising prospect for heavy metals treatment in aqueous phase. This article comprehensively summarized different types of biosorbents derived from available low-cost raw materials such as agricultural and forestry wastes. The raw materials obtained are treated with conventional pretreatment or novel methods, which can greatly enhance the adsorption performance of the biosorbents. The suitable immobilization methods can not only further enhance the adsorption performance of the biosorbents, but also facilitate the process of separating the biosorbents from the wastewater. In addition, once biosorbents are put into large-scale use, the final disposal problems cannot be avoided. Therefore, it is necessary to review the currently accepted final disposal methods of biosorbents. Moreover, through the analysis of the adsorption and desorption mechanisms of biosorbents, it is not only beneficial to find the better methods to improve the adsorption performance of the biosorbents, but also better to explain the influencing factors of adsorption effect for biosorbents. Especially, different from many researches focused on biosorbents, this work highlighted the combination of biosorbents with catalytic technologies, which provided new ideas for the follow-up research direction of biosorbents. Finally, the purpose of this paper is to inject new impetus into the future development of biosorbents.

Synthesis optimisation and characterisation of chitosan-calcite adsorbent from fishery-food waste for phosphorus removal

Here, Box-Behnken design (BBD) approaches were utilised to optimise synthesis methodology for the chitosan-calcite rich adsorbent (CCM) made from fishery-food waste material (crab carapace), using low-temperature activation and potassium hydroxide (KOH). The effect of activation temperature, activation time and impregnation ratio was studied. The final adsorbent material was evaluated for its phosphorus (P) removal efficiency from liquid phase. Results showed that impregnation ratio was the most significant individual factor as this acted to increase surface deacetylation of the chitin (to chitosan) and increased the number of amine groups (-NH₂) in the chitosan chain. P removal efficiency approached 75.89% (at initial P concentration of 20 mg/L) under optimised experimental conditions, i.e. where the impregnation ratio for KOH:carapace (g/g) was 1:1, the activation temperature was 105 °C and the activation time was 150 min. Predicted responses were in good agreement with the experimental data. Additionally, the pristine and CCM material were further analysed using scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), Brunauer-Emmett-Teller technique (BET), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis (TGA). Characterisation showed enhancements in surface chemistry (introducing positively charged amine groups), textural properties and thermal stability of the CCM.

Utilization of chemically treated cashew-nut shell as potential adsorbent for removal of Pb(II) ions from aqueous solution

In this study, cashew nut shells (CNS), waste from a cashew nut processing factory, have been used as an adsorbent for Pb(II) ions in water. Treatments of CNS with 1 M of H₂SO₄, HNO_3, and NaOH solutions were performed to modify their surfaces and improve their adsorption capacities. Characterization of untreated and chemical-treated CNS was carried out using nitrogen adsorption isotherm, elemental (CHN) analysis, Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) equipped with energy dispersive X-ray analysis (EDX). In the study of Pb(II) removal, various models of adsorption kinetics and isotherms were evaluated against the experimental data. The results showed that H₂SO₄-treated CNS exhibited the highest adsorption capacity. The chemical treatment removes impurities, alters the surface functional groups and improves specific surface areas and pore volumes of native CNS significantly. Surface adsorption and intra-particle diffusion steps were found to substantially affect the overall adsorption process of Pb(II) on H₂SO₄-treated CNS. Owing to its easy preparation and comparable adsorption capacity, H₂SO₄-treated CNS has the potential to be developed as a low-cost adsorbent for the removal of Pb(II) from contaminated water.

Recent advances in the recovery of metals from waste through biological processes

Wastes containing critical metals are generated in various fields, such as energy and computer manufacturing. Metal-bearing wastes are considered as secondary sources of critical metals. The conventional physicochemical methods of metals recovery are energy-intensive and cause further pollution. Low-cost and eco-friendly technologies including biosorbents, bioelectrochemical systems (BESs), bioleaching, and biomineralization, have become alternatives in the recovery of critical metals. However, a relatively low recovery rate and selectivity severely hinder their large-scale applications. Researchers have expanded their focus to exploit novel strain resources and strategies to improve the biorecovery efficiency. The mechanisms and potential applicability of modified biological techniques for improving the recovery of critical metals need more attention. Hence, this review summarize and compare the strategies that have been developed for critical metals recovery, and provides useful insights for energy-efficient recovery of critical metals in future industrial applications.

A Review of Chemicals to Produce Activated Carbon from Agricultural Waste Biomass

The choice of activating agent for the thermochemical production of high-grade activated carbon (AC) from agricultural residues and wastes, such as feedstock, requires innovative methods. Overcoming energy losses, and using the best techniques to minimise secondary contamination and improve adsorptivity, are critical. Here, we review the importance and influence of activating agents on agricultural waste: how they react and compare conventional and microwave processes. In particular, adsorbent pore characteristics, surface chemistry interactions and production modes were compared with traditional methods. It was concluded that there are no best activating agents; rather, each agent reacts uniquely with a precursor, and the optimum choice depends on the target adsorbent. Natural chemicals can also be as effective as inorganic activating agents, and offer the advantages that they are usually safe, and readily available. The use of a microwave, as an innovative pyrolysis approach, can enhance the activation process within a duration of 1–4 h and temperature of 500–1200 °C, after which the yield and efficiency decline rapidly due to molecular breakdown. This study also examines the biomass milling process requirements; the influence of the dielectric properties, along with the effect of washing; and experimental setup challenges. The microwave setup system, biomass feed rate, product delivery, inert gas flow rate, reactor design and recovery lines are all important factors in the microwave activation process, and contribute to the overall efficiency of AC preparation. However, a major issue is a lack of large-scale industrial demonstration units for microwave technology.

Influence of organic matter and CO2 supply on bioremediation of heavy metals by Chlorella vulgaris and Scenedesmus almeriensis in a multimetallic matrix

This research evaluated the influence of organic matter (OM) and CO₂ addition on the bioremediation potential of two microalgae typically used for wastewater treatment: Chlorella vulgaris (CV) and Scenedesmus almeriensis (SA). The heavy metal (HM) removal efficiencies and biosorption capacities of both microalgae were determined in multimetallic solutions (As, B, Cu, Mn, and Zn) mimicking the highest pollutant conditions found in the Loa river (Northern Chile). The presence of OM decreased the total biosorption capacity, specially in As (from 2.2 to 0.0 mg/g for CV and from 2.3 to 1.7 mg/g for SA) and Cu (from 3.2 to 2.3 mg/g for CV and from 2.1 to 1.6 mg/g for SA), but its influence declined over time. CO₂ addition decreased the total HM biosorption capacity for both microalgae species and inhibited CV growth. Finally, metal recovery using different eluents (HCl, NaOH, and CaCl₂) was evaluated at two different concentrations. HCl 0.1 M provided the highest recovery efficiencies, which supported values over 85% of As, 92% of Cu, and ≈100% of Mn and Zn from SA. The presence of OM during the loaded stage resulted in a complete recovery of As, Cu, Mn, and Zn when using HCl 0.1 M as eluent.

Lead sorption characteristics of various chicken bone part-derived chars

Recycling food waste for beneficial use is becoming increasingly important in resource-limited economy. In this study, waste chicken bones of different parts from restaurant industry were pyrolyzed at 600 °C and evaluated for char physicochemical properties and Pb sorption characteristics. Lead adsorption isotherms by different chicken bone chars were carried out with initial Pb concentration range of 1-1000 mg L^-1 at pH 5. The Pb adsorption data were better described by the Langmuir model (R² = 0.9289-0.9937; ARE = 22.7-29.3%) than the Freundlich model (R² = 0.8684-0.9544; ARE = 35.4-72.0%). Among the chars derived from different chicken bone parts, the tibia bone char exhibited the highest maximum Pb adsorption capacity of 263 mg g^-1 followed by the pelvis (222 mg g^-1), ribs (208 mg g^-1), clavicle (179 mg g^-1), vertebrae (159 mg g^-1), and humerus (135 mg g^-1). The Pb adsorption capacities were significantly and positively correlated with the surface area, phosphate release amount, and total phosphorus content of chicken bone chars (r ≥ 0.9711). On the other hand, approximately 75-88% of the adsorbed Pb on the chicken bone chars was desorbable with 0.1 M HCl, indicating their recyclability for reuse. Results demonstrated that chicken bone char could be used as an effective adsorbent for Pb removal in wastewater.

Biosorption technology for removal of toxic metals: a review of commercial biosorbents and patents

In last decades, the biosorption process has become one of the main alternative treatment technologies for the removal of pollutants from dilute aqueous solution. Among these pollutants, toxic metals have drawn attention due to their negative effects in human body and food chain. Even though biosorption is considered a cost-effective and eco-friendly technology to remove toxic metals from dilute wastewaters, there are still obstacles that restrain its commercialization. For this reason, various scientific articles and patents have been published each year to make more effective and economical this technology. This review reports an overview of past achievements, current research of biosorption studies, and future trends for the development of the biosorption as sustainable cleaner technology. Mechanisms of metal uptake, recovery and biosorbent regeneration, process design, commercial application of biosorbents, and patents registered are presented. Finally, future aspects in biosorption research and suggestions for its application will be discussed.

Immobilization of Lead and Nickel Ions from Polluted Yam Peels Biomass Using Cement-Based Solidification/Stabilization Technique

Nowadays, biomass has been employed to prepare biosorbents for heavy metals uptake; however, further disposal of polluted material has limited its application. In this work, nickel and lead removal was performed using yam peels and the resulting polluted biomass was mixed with concrete to produce bricks. The biomass was characterized by FT-IR analysis for testing functional groups diversification before and after adsorption process. The effect of adsorbent dosage, temperature, and initial solution concentration was evaluated to select suitable values of these parameters. Adsorption results were adjusted to kinetic and isotherm models to determine adsorption mechanism. Desorption experiments were also performed to determine the appropriate desorbing agent as well as its concentration. Immobilization technique of cement-based solidification/stabilization was applied and the polluted biomass was incorporated to concrete bricks at 5 and 10%. Mechanical resistance and leaching tests were carried out to analyze the suitability of heavy metals immobilization. The suitable values for dosage, temperature, and initial solution concentration were 0.5 g/L, 40°C and 100 ppm, respectively. The kinetic model that best fitted experimental results was pseudo-second order indicating a dominant physicochemical interaction between the two phases. The highest desorption yields were found in 52.47 and 74.84% for nickel and lead ions. The concrete bricks exhibited compression resistance above 5 MPa and all the leachate reported concentrations below the environmental limit. These results suggested that nickel and lead immobilization using concrete bricks is a good alternative to meet disposal problems of contaminated biomass.

Adsorption of Arsenic and Heavy Metals from Solutions by Unmodified Iron-Ore Sludge

Arsenic and heavy-metal-contaminated environments are a major concern due to their negative impacts on exposed people and ecosystems. In this study, sludge from an iron-ore processing area was used as an adsorbent to remove As, Mn, Zn, Cd, and Pb from aqueous solutions. The adsorption capacity of target adsorbates was investigated in batch experiments of both single- and mixed-metal solutions. The batch studies show that the maximum Langmuir adsorption capacities of the heavy metals onto the adsorbent occurred in the order Pb > As > Cd > Zn > Mn, and ranged from 0.710 mg/g to 1.113 mg/g in the single-metal solutions and from 0.370 mg/g to 1.059 mg/g in the mixed-metal solutions. The results of the kinetic experiments are consistent with pseudo-first-order and pseudo-second-order models, with a slightly better fit to the latter. Adsorption performances indicate that iron-ore sludge can simultaneously adsorb multiple metal ions and is a promising adsorbent for the removal of toxic pollutants from water.

Removing mercury from aqueous solution using sulfurized biochar and associated mechanisms

Biochar has been used to remove heavy metals from aqueous solutions. In this study, a sulfurized wood biochar (SWB) by direct impregnation with elemental sulfur was produced and evaluated along with pristine wood biochar (WB) for adsorption characteristics and mechanism of mercury. Mercury adsorption by WB and SWB was well described by Langmuir model and pseudo second order model and the maximum adsorption capacities of WB and SWB were 57.8 and 107.5 mg g^-1, respectively. Intraparticle diffusion model showed that mercury adsorption was fast due to boundary layer and slow adsorption due to diffusion into biochar pores. Although, mercury adsorption by both WB and SWB was predominantly influenced by the pH, temperature, salt concentration, and biochar dosage, the SWB showed a relatively stable mercury adsorption compared to WB under different conditions, suggesting the strong affinity of SWB for mercury. The XPS analysis showed different adsorption mechanisms of mercury between WB and SWB. In particular, mercury adsorption in WB was due to Hg-Cπ bond formation and interaction with carboxyl and hydroxyl groups, whereas in SWB it is primarily due to mercury interaction with C-SO_x-C and thiophenic groups in addition to Hg-Cπ bond formation and interaction with carboxyl groups. The SEM-EDS mapping also demonstrated that mercury in SWB was related to carbon, oxygen and sulfur. Overall, the sulfurized biochar was effective for removing mercury from aqueous solution, and its direct production through pyrolysis with elemental sulfur impregnation of wood chips could make it an economic option as absorbent for treating mercury-rich wastewater.

Characterization and mechanism of copper biosorption by a highly copper-resistant fungal strain isolated from copper-polluted acidic orchard soil

In this paper, a highly copper-resistant fungal strain NT-1 was characterized by morphological, physiological, biochemical, and molecular biological techniques. Physiological response to Cu(II) stress, effects of environmental factors on Cu(II) biosorption, as well as mechanisms of Cu(II) biosorption by strain NT-1 were also investigated in this study. The results showed that NT-1 belonged to the genus Gibberella, which exhibited high tolerance to both acidic conditions and Cu(II) contamination in the environment. High concentrations of copper stress inhibited the growth of NT-1 to various degrees, leading to the decreases in mycelial biomass and colony diameter, as well as changes in morphology. Under optimal conditions (initial copper concentration: 200 mg L^-1, temperature 28 °C, pH 5.0, and inoculum dose 10%), the maximum copper removal percentage from solution through culture of strain NT-1 within 5 days reached up to 45.5%. The biosorption of Cu(II) by NT-1 conformed to quasi-second-order kinetics and Langmuir isothermal adsorption model and was confirmed to be a monolayer adsorption process dominated by surface adsorption. The binding of NT-1 to Cu(II) was mainly achieved by forming polydentate complexes with carboxylate and amide group through covalent interactions and forming Cu-nitrogen-containing heterocyclic complexes via Cu(II)-π interaction. The results of this study provide a new fungal resource and key parameters influencing growth and copper removal capacity of the strain for developing an effective bioremediation strategy for copper-contaminated acidic orchard soils.

Surface treated Pteris vittata L. pinnae powder used as an efficient biosorbent of Pb(II), Cd(II), and Cr(VI) from aqueous solution

Biosorption is a surface-dependent phenomenon. Surface modifications by chemical treatment methods could either improve or reduce the biosorption capacity of potential biosorbents. In the present work, pristine Pteris vittata L. pinnae (PPV) powder was treated separately with sodium hydroxide (NaOH), calcium chloride (CaCl₂), and nitric acid (HNO₃). The pristine and treated biosorbents were used to assess the biosorption of Pb(II), Cd(II), and Cr(VI) as a function of pH. Kinetics and adsorption isotherms were studied. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and scanning electron microscope combined with energy dispersive x-ray (SEM-EDX) spectroscopic techniques were used to characterize the biosorbents before and after chemical treatments. The possible functional groups contributing to the metal sorption were identified. Results revealed favorable biosorption of Pb(II), Cd(II), and Cr(VI) described by pseudo-second order kinetics. NaOH-treated P. vittata (NPV) showed higher biosorption capacity for Pb(II) and Cd(II) compared to that of PPV. ATR-FTIR studies indicated that -OH, -COOH, and -NH₂ groups were mainly involved in Cr(VI) and -OH in Pb(II) and Cd(II) biosorption. The enhanced efficiency of NPV and CaCl₂ treated P. vittata (CPV) in the uptake of Pb(II) and Cd(II) compared to PPV can be associated with their altered physicochemical characters.

Adsorption and desorption of potentially toxic metals on modified biosorbents through new green grafting process

Six lignocellulosic waste-derived biosorbents [cantaloupe peel (CAN), pine cone (PC), litchi fruit peel (LP), annona squamosal (AS), bamboo shoot (BS), and sugarcane bagasse (SB)] were selected as low-cost and renewable materials to prepare chemically modified biosorbent. The modified biosorbent was prepared through a newer carboxyl groups-grafting process onto the biosorbent's surface using acrylic acid. The results showed that the cation exchange capacity (CEC) of biosorbents increased by approximately 66.3-104% after modified. The modified biosorbent exhibited significantly higher adsorption capacity of Pb²⁺, Cu²⁺, and Cd²⁺ ions than the pristine biosorbent. The maximum Langmuir adsorption capacity (Q^o_max) of both pristine and modified biosorbents toward three metal ions (Pb²⁺, Cu²⁺, and Cd²⁺) followed the decreasing order: CAN > PC > LP > AS > BS > SB. The preference ranking of three metal ions on the pristine and modified biosorbents (mmol/kg) was generally in the order: Pb²⁺ > Cu²⁺ > Cd²⁺. Among these biosorbents, cantaloupe peel exhibited an excellent adsorption affinity to metal cations compared to the five others. The Q^o_max values of modified and pristine cantaloupe peels were ordered as follows: 143.2 and 81.1 mg/g for Pb²⁺ adsorption, > 45.4 and 30.4 mg/g for Cd²⁺ adsorption, > 33.1 and 23.5 mg/g for Cu²⁺ adsorption. After five adsorption-desorption cycles, the removal efficiency of Pb²⁺ by modified CAN was maintained at around 70%. The ion exchange played a determining role in adsorption mechanism. It can be concluded that modified cantaloupe peel can serve as a newer and promising biosorbent with a high adsorption capacity to various potentially toxic metals.

Ni2+ and Co2+ adsorption using Tectona grandis biochar: kinetics, equilibrium and desorption studies

In this research, the potential of a relatively new adsorbent prepared from Tectona grandis leaves by pyrolysis for heavy metal removal from aqueous solution was studied. Adsorption behavior of the pyrolytic biochar was investigated with respect to Ni²⁺ and Co²⁺ removal with its affinity examined through batch studies and the mechanism elucidated using different empirical isotherm and kinetic models. A significantly higher efficiency of 92.46% and 91.21% was achieved at a weakly acidic pH of 6 and 5, dose of 3 g L^-1 and 2 g L^-1 for Ni²⁺ and Co²⁺ removal, respectively. Pseudo-second-order kinetics and Langmuir isotherm model best represented the adsorption process for both Ni²⁺ and Co²⁺. Thermodynamic analysis proved the endothermic and spontaneous nature of the process. Desorption studies revealed hydrochloric acid to have a high potential toward eluting the adsorbed metal ions. The well-organized microporous structure, the significant surface area value along with the presence of relative functional groups together with its high adsorption capacity for Ni²⁺ and Co²⁺, revealed the significant adsorptive potential of biochar of teak leaves powder for metal ion removal.

Investigations of Heavy Metal Ion Sorption Using Nanocomposites of Iron-Modified Biochar

Magnetic biochar nanocomposites were obtained by modification of biochar by zero-valent iron. The article provides information on the impact of contact time, initial Cd(II), Co(II), Zn(II), and Pb(II) ion concentrations, dose of the sorbents, solution pH and temperature on the adsorption capacity. On the basis of experiments, it was found that the optimum parameters for the sorption process are phase contact time 360 min (after this time, the equilibrium of all concentrations is reached), the dose of sorbent equal to 5 g/dm³, pH 5 and the temperature 295 K. The values of parameters calculated from the kinetic models and isotherms present the best match to the pseudo second order and Langmuir isotherm models. The calculated thermodynamic parameters ∆H ⁰, ∆S ⁰ and ∆G ⁰ indicate that the sorption of heavy metal ions is an exothermic and spontaneous process as well as favoured at lower temperatures, suggesting the physical character of sorption. The solution of nitric acid(V) at the concentration 0.1 mol/dm³ was the best acidic desorbing agent used for regeneration of metal-loaded magnetic sorbents. The physicochemical properties of synthesized composites were characterized by FTIR, SEM, XRD, XPS and TG analyses. The point characteristics of the double layer for biochar pH_PZC and pH_IEP were designated.

Adsorption of iron(III), cobalt(II), and nickel(II) on activated carbon derived from Xanthoceras Sorbifolia Bunge hull: mechanisms, kinetics and influencing parameters

Xanthoceras Sorbifolia Bunge hull activated carbon (XSA) was prepared and characterized by Brunauer-Emmett-Teller analysis, scanning electron microscopy and energy dispersive X-ray (EDX) spectroscopy. The ability of XSA as an adsorbent was investigated for the removal of the iron group ions Fe(III), Co(II), and Ni(II) from aqueous solution. Optimum adsorption parameters were determined based on the initial concentrations of the iron group ions, pH, adsorption temperature, and adsorption time in adsorption studies. The maximum monolayer adsorption capacities were 241.13 mg/g for Fe(III), 126.05 mg/g for Co(II), and 187.96 mg/g for Ni(II), respectively. Adsorption kinetics and isotherms showed that the adsorption process best fitted the nonlinear pseudo-second-order and Langmuir models, and the affinity of the ions for XSA decreased as follows: Fe(III) > Ni(II) > Co(II). Regeneration studies indicated that XSA could be used after several consecutive adsorption/desorption cycles using HNO₃. Fourier transform infrared and EDX spectra revealed the chemical adsorption value of XSA as an adsorbent for removing iron group ions from aqueous solutions.

Application of a breakthrough biosorbent for removing heavy metals from synthetic and real wastewaters in a lab-scale continuous fixed-bed column

A continuous fixed-bed study was carried out utilising a breakthrough biosorbent, specifically multi-metal binding biosorbent (MMBB) for removing cadmium, copper, lead and zinc. The effect of operating conditions, i.e. influent flow rate, metal concentration and bed depth was investigated at pH 5.5±0.1 for a synthetic wastewater sample. Results confirmed that the total amount of metal adsorption declined with increasing influent flow rate and also rose when each metal concentration also increased. The maximum biosorption capacities of 38.25, 63.37, 108.12 and 35.23mg/g for Cd, Cu, Pb and Zn, respectively, were achieved at 31cm bed height, 10mL/min flow rate and 20mg/L initial concentration. The Thomas model better described the whole dynamic behaviour of the column rather than the Dose Response and Yoon-Nelson models. Finally, desorption studies indicated that metal-loaded biosorbent could be used after three consecutive sorption, desorption and regeneration cycles by applying a semi-simulated real wastewater.

Studies on Characterization of Corn Cob for Application in a Gasification Process for Energy Production

Quintessential characteristics of corn cob were investigated in this study in order to determine its gasification potential. Results were interpreted in relation to gasification with reference to existing data from the literature. The results showed that the gasification of corn cob may experience some challenges related to ash fouling, slagging, and sintering effects that may be orchestrated by high ash content recorded for corn cob, which may contribute to increasing concentration of inorganic elements under high temperature gasification conditions, even though EDX analysis showed reduced concentration of these elements. The study also found that the weight percentages of other properties such as moisture, volatile matter, and fixed carbon contents of corn cob as well as its three major elemental components (C, H, and O) including its clearly exhibited fiber cells make corn cob a suitable feedstock for gasification. FTIR analysis revealed the existence of –OH, C–O, C–H, and C=C as the major functional group of atoms in the structure of corn cob that may facilitate formation of condensable and noncondensable liquid and gaseous products during gasification. TGA results indicated that complete thermal decomposition of corn cob occurs at temperatures close to 1000°C at a heating rate of 20°C/min.