Simultaneous saccharification and co-fermentation of dry diluted acid pretreated corn stover at high dry matter loading: Overcoming the inhibitors by non-tolerant yeast

Optimizing the Conditions of Pretreatment and Enzymatic Hydrolysis of Sugarcane Bagasse for Bioethanol Production

The agricultural waste sugarcane bagasse (SCB) is a kind of plentiful biomass resource. In this study, different pretreatment methods (NaOH, H2SO4, and sodium percarbonate/glycerol) were utilized and compared. Among the three pretreatment methods, NaOH pretreatment was the most optimal method. Response surface methodology (RSM) was utilized to optimize NaOH pretreatment conditions. After optimization by RSM, the solid yield and lignin removal were 54.60 and 82.30% under the treatment of 1% NaOH, a time of 60 min, and a solid-to-liquid ratio of 1:15, respectively. Then, the enzymolysis conditions of cellulase for NaOH-treated SCB were optimized by RSM. Under the optimal enzymatic hydrolysis conditions (an enzyme dose of 18 FPU/g, a time of 64 h, and a solid-to-liquid ratio of 1:30), the actual yield of reducing sugar in the enzyme-treated hydrolysate was 443.52 mg/g SCB with a cellulose conversion rate of 85.33%. A bacterium, namely, Bacillus sp. EtOH, which produced ethanol and Baijiu aroma substances, was isolated from the high-temperature Daqu of Danquan Baijiu in our previous study. At last, when the strain EtOH was cultured for 36 h in a fermentation medium (reducing sugar from cellulase-treated SCB hydrolysate, yeast extract, and peptone), ethanol concentration reached 2.769 g/L (0.353%, v/v). The sugar-to-ethanol and SCB-to-ethanol yields were 13.85 and 11.81% in this study, respectively. In brief, after NaOH pretreatment, 1 g of original SCB produced 0.5460 g of NaOH-treated SCB. Then, after the enzymatic hydrolysis, reducing sugar yield (443.52 mg/g SCB) was obtained. Our study provided a suitable method for bioethanol production from SCB, which achieved efficient resource utilization of agricultural waste SCB.

Enhancing xylose-fermentation capacity of engineered Saccharomyces cerevisiae by multistep evolutionary engineering in inhibitor-rich lignocellulose hydrolysate

Major progress in developing Saccharomyces cerevisiae strains that utilize the pentose sugar xylose has been achieved. However, the high inhibitor content of lignocellulose hydrolysates still hinders efficient xylose fermentation, which remains a major obstacle for commercially viable second-generation bioethanol production. Further improvement of xylose utilization in inhibitor-rich lignocellulose hydrolysates remains highly challenging. In this work, we have developed a robust industrial S. cerevisiae strain able to efficiently ferment xylose in concentrated undetoxified lignocellulose hydrolysates. This was accomplished with novel multistep evolutionary engineering. First, a tetraploid strain was generated and evolved in xylose-enriched pretreated spruce biomass. The best evolved strain was sporulated to obtain a genetically diverse diploid population. The diploid strains were then screened in industrially relevant conditions. The best performing strain, MDS130, showed superior fermentation performance in three different lignocellulose hydrolysates. In concentrated corncob hydrolysate, with initial cell density of 1 g DW/l, at 35°C, MDS130 completely coconsumed glucose and xylose, producing ± 7% v/v ethanol with a yield of 91% of the maximum theoretical value and an overall productivity of 1.22 g/l/h. MDS130 has been developed from previous industrial yeast strains without applying external mutagenesis, minimizing the risk of negative side-effects on other commercially important properties and maximizing its potential for industrial application.

Efficient Fractionation and Catalytic Valorization of Raw Biomass in ϵ-Caprolactone and Water

Efficient fractionation and utilization of the whole biomass is particularly attractive but remains a great challenge, owing to the recalcitrance of biomass. In this study, a simple and efficient approach is developed to obtain high-purity cellulose with a delignification degree of 97.5 % in ϵ-caprolactone and water. FTIR spectroscopy reveals that ϵ-caprolactone and water act in synergy to remove lignin from raw biomass and afford cellulose with clear macrofibrils. A linear positive correlation between the contents of hemicellulose and lignin is observed for the separated cellulose pulp. This mixed solvent exhibits good performance for the removal of lignin from various agricultural and forestry wastes. Moreover, nearly complete transformation of the whole biomass constituents is achieved with Ni-Al catalyst.

Pretreatment of sugarcane bagasse with acid catalyzed ethylene glycol-water to improve the cellulose enzymatic conversion

In this work, HCl catalyzed ethylene glycol-water pretreatment (HCl/EG-H₂O) of sugarcane bagasse (SCB) was explored with response surface methodology (RSM) and single factor analysis, which aim to investigate the influence of pretreatment variable on pretreated solid cellulose enzymatic conversion. The result showed that HCl/EG-H₂O pretreatment could selectively extract ∼89.9 % xylan and ∼61.2 % lignin in SCB, meanwhile maintain a relatively high cellulose retention (∼86.8 %). Pretreatment of SCB at 120 °C for 60 min with 1.00 % HCl and 90 % EG obtained the pretreated solid having maximum cellulose enzymatic conversion of 88.7 % under 10 FPU/g enzyme dosage, this enhancement of cellulose enzymatic conversion mainly attributed to structure change of SCB in pretreatment. The adding of enzymatic additives into the hydrolysis process could not only improve hydrolysis efficiency but also lower the enzyme dosage. Besides, the linear relationship between substrate characteristic parameters (such cellulose content, lignin removal rate etc.) and cellulose conversion were observed.

High-solids loading processing for an integrated lignocellulosic biorefinery: Effects of transport phenomena and rheology - A review

This review aims to present an analysis and discussion on the processing of lignocellulosic biomass in terms of biorefinery concept and circular bioeconomy operating at high solids lignocellulosic (above 15% [w/w]) at the pretreatment, enzymatic hydrolysis stage, and fermentation strategy for an integrated lignocellulosic bioprocessing. Studies suggest high solids concentration enzymatic hydrolysis for improved sugars yields and methods to overcome mass transport constraints. Rheological and computational fluid dynamics models of high solids operation through evaluation of mass and momentum transfer limitations are presented. Also, the review paper explores operational feeding strategies to obtain high ethanol concentration and conversion yield, from the hydrothermal pretreatment and investigates the impact of mass load over the operational techniques. Finally, this review contains a brief overview of some of the operations that have successfully scaled up and implemented high-solids enzymatic hydrolysis in terms of the biorefinery concept.

Coprocessing Corn Germ Meal for Oil Recovery and Ethanol Production: A Process Model for Lipid-Producing Energy Crops

Efforts to engineer high-productivity crops to accumulate oils in their vegetative tissue present the possibility of expanding biodiesel production. However, processing the new crops for lipid recovery and ethanol production from cell wall saccharides is challenging and expensive. In a previous study using corn germ meal as a model substrate, we reported that liquid hot water (LHW) pretreatment enriched the lipid concentration by 2.2 to 4.2 fold. This study investigated combining oil recovery with ethanol production by extracting oil following LHW and simultaneous saccharification and co-fermentation (SSCF) of the biomass. Corn germ meal was again used to model the oil-bearing energy crops. Pretreated germ meal hydrolysate or solids (160 and 180 °C for 10 min) were fermented, and lipids were extracted from both the spent fermentation whole broth and fermentation solids, which were recovered by centrifugation and convective drying. Lipid contents in spent fermentation solids increased 3.7 to 5.7 fold compared to the beginning germ meal. The highest lipid yield achieved after fermentation was 36.0 mg lipid g−1 raw biomass; the maximum relative amount of triacylglycerol (TAG) was 50.9% of extracted oil. Although the fermentation step increased the lipid concentration of the recovered solids, it did not improve the lipid yields of pretreated biomass and detrimentally affected oil compositions by increasing the relative concentrations of free fatty acids.

Effects of post-washing on pretreated biomass and hydrolysis of the mixture of acetic acid and sodium hydroxide pretreated biomass and their mixed filtrate

Effects of post-washing [one-volume water (I-VW) or double-volume water (Ⅱ-VW)] on pretreated hemp and poplar biomass and enzymatic hydrolysis of the mixture of HOAc and NaOH pretreated biomass and their mixed filtrate were investigated. Compared to I-VW, Ⅱ-VW increased 3.76-6.80% of glucan content in NaOH pretreated biomass, diminished lignin recondensation, and heightened cellulose-related FTIR peak intensities, crystallinity index, and lignin removal. The pH of mixed filtrate was around 4.80, precipitating the NaOH soluble lignin partially. Although Ⅱ-VW showed lower lignin recoveries than I-VW, their FTIR characteristics were equivalent to the commercial alkali lignin. Enzymatic hydrolysis at solid loadings of 2.5-10% (w/v) demonstrated that I-VW and Ⅱ-VW had marginal variations in sugar concentration and conversion efficiency, indicating that I-VW is sufficient for post-washing pretreated biomass. Glucose concentration exhibited a quadratic correlation with solid loading and hemp biomass reached the maximum glucose (43.88 g/L) and total sugar (57.08 g/L) concentrations with I-VW.

Engineering prokaryotic regulator IrrE to enhance stress tolerance in budding yeast

BACKGROUND

Stress tolerance is one of the important desired microbial traits for industrial bioprocesses, and global regulatory protein engineering is an efficient approach to improve strain tolerance. In our study, IrrE, a global regulatory protein from the prokaryotic organism Deinococcus radiodurans, was engineered to confer yeast improved tolerance to the inhibitors in lignocellulose hydrolysates or high temperatures.

RESULTS

Three IrrE mutations were developed through directed evolution, and the expression of these mutants could improve the yeast fermentation rate by threefold or more in the presence of multiple inhibitors. Subsequently, the tolerance to multiple inhibitors of single-site mutants based on the mutations from the variants were then evaluated, and 11 mutants, including L65P, I103T, E119V, L160F, P162S, M169V, V204A, R244G, Base 824 Deletion, V299A, and A300V were identified to be critical for the improved representative inhibitors, i.e., furfural, acetic acid and phenol (FAP) tolerance. Further studies indicated that IrrE caused genome-wide transcriptional perturbation in yeast, and the mutant I24 led to the rapid growth of Saccharomyces cerevisiae by primarily regulating the transcription level of transcription activators/factors, protecting the intracellular environment and enhancing the antioxidant capacity under inhibitor environments, which reflected IrrE plasticity. Meanwhile, we observed that the expression of the wild-type or mutant IrrE could also protect Saccharomyces cerevisiae from the damage caused by thermal stress. The recombinant yeast strains were able to grow with glucose at 42 ℃.

CONCLUSIONS

IrrE from Deinococcus radiodurans can be engineered as a tolerance-enhancer for Saccharomyces cerevisiae. Systematic research on the regulatory model and mechanism of a prokaryotic global regulatory factor IrrE to increase yeast tolerance provided valuable insights for the improvements in microbial tolerance to complex industrial stress conditions.

Sustainable environmental management and related biofuel technologies

Environmental sustainability criteria and rising energy demands, exhaustion of conventional resources of energy followed by environmental degradation due to abrupt climate changes have shifted the attention of scientists to seek renewable sources of green and clean energy for sustainable development. Bioenergy is an excellent alternative since it can be applied for several energy-requirements after utilizing suitable conversion methodology. This review elucidates all aspects of biofuels (bioethanol, biodiesel, and butanol) and their sustainability criteria. The principal focus is on the latest developments in biofuel production chiefly stressing on the role of nanotechnology. A plethora of investigations regarding the emerging techniques for process improvement like integration methods, less energy-intensive distillation techniques, and bioengineering of microorganisms are discussed. This can assist in making biofuel-production in a real-world market more economically and environmentally viable.

Progress in the development of alkali and metal salt catalysed lignocellulosic pretreatment regimes: Potential for bioethanol production

Lignocellulosic biomass (LCB) is well suited to address present day energy and environmental concerns, since it is abundant, environmentally benign and sustainable. However, the commercial application of LCB has been limited by its recalcitrant structure. To date, several biomass pretreatment systems have been developed to address this major bottleneck but have shown to be toxic and costly. Alkali and metal salt pretreatment regimes have emerged as promising non-toxic and low-cost treatments. This paper examines the progress made in lignocellulosic pretreatment using alkali and metal salts. The reaction mechanism of alkali and metal chloride salts on lignocellulosic biomass degradation are reviewed. The effect of salt pretreatment on lignin removal, hemicellulose solubilization, cellulose crystallinity, and physical structural changes are also presented. In addition, the enzymatic digestibility and inhibitor profile from salt pretreated lignocellulosic biomass are discussed. Furthermore, the challenges and future prospects on lignocellulosic pretreatment and bioethanol production are highlighted.

Pre-treatment of sugarcane bagasse with aqueous ammonia-glycerol mixtures to enhance enzymatic saccharification and recovery of ammonia

In this work, an efficient aqueous ammonia with glycerol (AAWG) method to improve the digestibility of sugarcane bagasse (SCB) was developed. Response surface methodology was utilized to optimize the AAWG parameters to achieve the maximum total fermentable sugar concentration (TFSC) and total fermentable sugar yield (TFSY). Under optimal AAWG conditions, 13.59 g/L TFSC (9.25% ammonia, 1.86 h, 180 °C) and 0.4449 g/g TFSY (9.51% ammonia, 1.78 h, 180 °C) were achieved, with delignification of 77.81% and 70.91%, respectively. Compared to pretreatment with glycerol or aqueous ammonia, the AAWG method significantly enhanced the enzymatic efficiency of SCB. The ammonia was recovered from the pretreatment liquid by distillation, and about one-third of the ammonia was retained. The overall results indicate that AAWG is effectively used as a pretreatment method for recovering ammonia, which would largely contribute to the economic benefits of biomass biorefinery.

Microbial Lipid Production from Corn Stover by the Oleaginous Yeast Rhodosporidium toruloides Using the PreSSLP Process

Dry acid pretreatment and biodetoxification (DryPB) has been considered as an advanced technology to treat lignocellulosic materials for improved downstream bioconversion. In this study, the lipid production from DryPB corn stover was investigated by the oleaginous yeast Rhodosporidium toruloides using a new process designated prehydrolysis followed by simultaneous saccharification and lipid production (PreSSLP). The results found that prehydrolysis at 50 °C and then lipid production at 30 °C improved lipid yield by more than 17.0% compared with those without a prehydrolysis step. The highest lipid yield of 0.080 g/g DryPB corn stover was achieved at a solid loading of 12.5%. The fatty acid distribution of lipid products was similar to those of conventional vegetable oils that are used for biodiesel production. Our results suggested that the integration of DryPB process and PreSSLP process can be explored as an improved technology for microbial lipid production from lignocellulosic materials.

Biochemical engineering in China

Chinese biochemical engineering is committed to supporting the chemical and food industries, to advance science and technology frontiers, and to meet major demands of Chinese society and national economic development. This paper reviews the development of biochemical engineering, strategic deployment of these technologies by the government, industrial demand, research progress, and breakthroughs in key technologies in China. Furthermore, the outlook for future developments in biochemical engineering in China is also discussed.

Ethylenediamine pretreatment of corn stover facilitates high gravity fermentation with low enzyme loading

This work investigated the effect of ethylenediamine pretreatment on reducing enzyme loading in high gravity fermentation. At optimal conditions of ethylenediamine pretreatment, 85.5% lignin was removed. Enzyme adsorption analysis using a fluorescent cellulose-binding protein showed 35.2% increase of productive adsorption of enzymes to ethylenediamine pretreated biomass, which was caused by high delignification and dramatically increased surface roughness and porosity. In SScF at 15% glucan loading, up to 82.2 g/L ethanol was achieved with a relatively low enzyme loading of 3.6 FPU/g dry matter. It suggested that the remarkably high digestibility of EDA pretreated corn stover could effectively reduce the enzyme loading in the high gravity fermentation of cellulosic ethanol.

Simultaneous saccharification and bioethanol production from corn cobs: Process optimization and kinetic studies

This study investigates the simultaneous saccharification and fermentation (SSF) process for bioethanol production from corn cobs with prehydrolysis (PSSF) and without prehydrolysis (OSSF). Two response surface models were developed with high coefficients of determination (>0.90). Process optimization gave high bioethanol concentrations and bioethanol conversions for the PSSF (36.92 ± 1.34 g/L and 62.36 ± 2.27%) and OSSF (35.04 ± 0.170 g/L and 58.13 ± 0.283%) models respectively. Additionally, the logistic and modified Gompertz models were used to study the kinetics of microbial cell growth and ethanol formation under microaerophilic and anaerobic conditions. Cell growth in the OSSF_{microaerophilic} process gave the highest maximum specific growth rate (µ_max) of 0.274 h^-1. The PSSF_{microaerophilic} bioprocess gave the highest potential maximum bioethanol concentration (P_m) (42.24 g/L). This study demonstrated that microaerophilic rather than anaerobic culture conditions enhanced cell growth and bioethanol production, and that additional prehydrolysis steps do not significantly impact on the bioethanol concentration and conversion in SSF process.

Process analysis and optimization of simultaneous saccharification and co-fermentation of ethylenediamine-pretreated corn stover for ethanol production

BACKGROUND

Improving ethanol concentration and reducing enzyme dosage are main challenges in bioethanol refinery from lignocellulosic biomass. Ethylenediamine (EDA) pretreatment is a novel method to improve enzymatic digestibility of lignocellulose. In this study, simultaneous saccharification and co-fermentation (SSCF) process using EDA-pretreated corn stover was analyzed and optimized to verify the constraint factors on ethanol production.

RESULTS

Highest ethanol concentration was achieved with the following optimized SSCF conditions at 6% glucan loading: 12-h pre-hydrolysis, 34 °C, pH 5.4, and inoculum size of 5 g dry cell/L. As glucan loading increased from 6 to 9%, ethanol concentration increased from 33.8 to 48.0 g/L, while ethanol yield reduced by 7%. Mass balance of SSCF showed that the reduction of ethanol yield with the increasing solid loading was mainly due to the decrease of glucan enzymatic conversion and xylose metabolism of the strain. Tween 20 and BSA increased ethanol concentration through enhancing enzymatic efficiency. The solid-recycled SSCF process reduced enzyme dosage by 40% (from 20 to 12 mg protein/g glucan) to achieve the similar ethanol concentration (~ 40 g/L) comparing to conventional SSCF.

CONCLUSIONS

Here, we established an efficient SSCF procedure using EDA-pretreated biomass. Glucose enzymatic yield and yeast viability were regarded as the key factors affecting ethanol production at high solid loading. The extensive analysis of SSCF would be constructive to overcome the bottlenecks and improve ethanol production in cellulosic ethanol refinery.

Endogenous lycopene improves ethanol production under acetic acid stress in Saccharomyces cerevisiae

BACKGROUND

Acetic acid, generated from the pretreatment of lignocellulosic biomass, is a significant obstacle for lignocellulosic ethanol production. Reactive oxidative species (ROS)-mediated cell damage is one of important issues caused by acetic acid. It has been reported that decreasing ROS level can improve the acetic acid tolerance of Saccharomyces cerevisiae.

RESULTS

Lycopene is known as an antioxidant. In the study, we investigated effects of endogenous lycopene on cell growth and ethanol production of S. cerevisiae in acetic acid media. By accumulating endogenous lycopene during the aerobic fermentation of the seed stage, the intracellular ROS level of strain decreased to 1.4% of that of the control strain during ethanol fermentation. In the ethanol fermentation system containing 100 g/L glucose and 5.5 g/L acetic acid, the lag phase of strain was 24 h shorter than that of control strain. Glucose consumption rate and ethanol titer of yPS002 got to 2.08 g/L/h and 44.25 g/L, respectively, which were 2.6- and 1.3-fold of the control strain. Transcriptional changes of INO1 gene and CTT1 gene confirmed that endogenous lycopene can decrease oxidative stress and improve intracellular environment.

CONCLUSIONS

Biosynthesis of endogenous lycopene is first associated with enhancing tolerance to acetic acid in S. cerevisiae. We demonstrate that endogenous lycopene can decrease intracellular ROS level caused by acetic acid, thus increasing cell growth and ethanol production. This work innovatively   puts forward a new strategy for second generation bioethanol production during lignocellulosic fermentation.

Optimization of cellulolytic enzyme components through engineering Trichoderma reesei and on-site fermentation using the soluble inducer for cellulosic ethanol production from corn stover

BACKGROUND

Cellulolytic enzymes produced by Trichoderma reesei are widely studied for biomass bioconversion, and enzymatic components vary depending on different inducers. In our previous studies, a mixture of glucose and disaccharide (MGD) was developed and used to induce cellulase production. However, the enzymatic profile induced by MGD is still not defined, and further optimization of the enzyme cocktail is also required for efficient ethanol production from lignocellulosic biomass.

RESULTS

In this study, cellulolytic enzymes produced by T. reesei Rut C30 using MGD and alkali-pretreated corn stover (APCS) as inducer were compared. Cellular secretome in response to each inducer was analyzed, which revealed a similar enzyme profile. However, significant difference in the content of cellulases and xylanase was detected. Although MGD induction enhanced β-glucosidase production, its activity was still not sufficient for biomass hydrolysis. To overcome such a disadvantage, aabgl1 encoding β-glucosidase in Aspergillus aculeatus was heterologously expressed in T. reesei Rut C30 under the control of the pdc1 promoter. The recombinant T. reesei PB-3 strain showed an improved β-glucosidase activity of 310 CBU/mL in the fed-batch fermentation, 71-folds higher than that produced by the parent strain. Meanwhile, cellulase activity of 50 FPU/mL was detected. Subsequently, the crude enzyme was applied for hydrolyzing corn stover with a solid loading of 20% through separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation, respectively, for ethanol production. Better performance was observed in the SHF process, through which a total of 119.9 g/L glucose was released within 12 h for concomitant ethanol production of 54.2 g/L.

CONCLUSIONS

The similar profile of cellulolytic enzymes was detected under the induction of MGD and APCS, but higher amount of cellulases was present in the crude enzyme induced by MGD. However, β-glucosidase activity induced by MGD was not sufficient for hydrolyzing lignocellulosic biomass. High titers of cellulases and β-glucosidase were achieved simultaneously by heterologous expression of aabgl1 in T. reesei and fed-batch fermentation through feeding MGD. We demonstrated that on-site cellulase production by T. reesei PB-3 has a potential for efficient biomass saccharification and ethanol production from lignocellulosic biomass.

Comparison of microwave and conduction-convection heating autohydrolysis pretreatment for bioethanol production

This work describes the application of two forms of heating for autohydrolysis pretreatment on isothermal regimen: conduction-convection heating and microwave heating processing using corn stover as raw material for bioethanol production. Pretreatments were performed using different operational conditions: residence time (10-50 min) and temperature (160-200°C) for both pretreatments. Subsequently, the susceptibility of pretreated solids was studied using low enzyme loads, and high substrate loads. The highest conversion was 95.1% for microwave pretreated solids. Also solids pretreated by microwave heating processing showed better ethanol conversion in simultaneous saccharification and fermentation process (92% corresponding to 33.8g/L). Therefore, microwave heating processing is a promising technology in the pretreatment of lignocellulosic materials.

Production of high concentrated cellulosic ethanol by acetone/water oxidized pretreated beech wood

BACKGROUND

Lignocellulosic biomass is an abundant and inexpensive resource for biofuel production. Alongside its biotechnological conversion, pretreatment is essential to enable efficient enzymatic hydrolysis by making cellulose susceptible to cellulases. Wet oxidation of biomass, such as acetone/water oxidation, that employs hot acetone, water, and oxygen, has been found to be an attractive pretreatment method for removing lignin while producing less degradation products. The remaining enriched cellulose fraction has the potential to be utilized under high gravity enzymatic saccharification and fermentation processes for the cost-competing production of bioethanol.

RESULTS

Beech wood residual biomass was pretreated following an acetone/water oxidation process aiming at the production of high concentration of cellulosic ethanol. The effect of pressure, reaction time, temperature, and acetone-to-water ratio on the final composition of the pretreated samples was studied for the efficient utilization of the lignocellulosic feedstock. The optimal conditions were acetone/water ratio 1:1, 40 atm initial pressure of 40 vol% O₂ gas, and 64 atm at reaction temperature of 175 °C for 2 h incubation. The pretreated beech wood underwent an optimization step studying the effect of enzyme loading and solids content on the enzymatic liquefaction/saccharification prior to fermentation. In a custom designed free-fall mixer at 50 °C for either 6 or 12 h of prehydrolysis using an enzyme loading of 9 mg/g dry matter at 20 wt% initial solids content, high ethanol concentration of 75.9 g/L was obtained.

CONCLUSION

The optimization of the pretreatment process allowed the efficient utilization of beech wood residual biomass for the production of high concentrations of cellulosic ethanol, while obtaining lignin that can be upgraded towards high-added-value chemicals. The threshold of 4 wt% ethanol concentration that is required for the sustainable bioethanol production was surpassed almost twofold, underpinning the efficient conversion of biomass to ethanol and bio-based chemicals on behalf of the biorefinery concept.

Dual effect of soluble materials in pretreated lignocellulose on simultaneous saccharification and co-fermentation process for the bioethanol production

In this study, wash liquors isolated from ethylenediamine and dry dilute acid pretreated corn stover were used to evaluate the effect of soluble materials in pretreated biomass on simultaneous saccharification and co-fermentation (SSCF) for ethanol production, respectively. Both of the wash liquors had different impacts on enzymatic hydrolysis and fermentation. Enzymatic conversions of glucan and xylan monotonically decreased as wash liquor concentration increased. Whereas, with low wash liquor concentrations, xylose consumption rate, cell viability and ethanol yield were maximally stimulated in fermentation without nutrient supplementary. Soluble lignins were found as the key composition which promoted sugars utilization and cell viability without nutrient supplementary. The dual effects of soluble materials on enzymatic hydrolysis and fermentation resulted in the reduction of ethanol yield as soluble materials increased in SSCF.

Reducing sugar loss in enzymatic hydrolysis of ethylenediamine pretreated corn stover

In this study, the effect of ethylenediamine (EDA) on enzymatic hydrolysis with different cellulosic substrates and the approaches to reduce sugar loss in enzymatic hydrolysis were investigated. During enzymatic hydrolysis, xylose yield reduced 21.2%, 18.1% and 13.0% with 7.5mL/L EDA for AFEX pretreated corn stover (CS), washed EDA pretreated CS and CS cellulose. FTIR and GPC analysis demonstrated EDA reacted with sugar and produced high molecular weight (MW) compounds. EDA was prone to react with xylose other than glucose. H₂O₂ and Na₂SO₃ cannot prevent sugar loss in glucose/xylose-EDA mixture, although they inhibited the browning and high MW compounds formation. By decreasing temperature to 30°C, the loss of xylose yield reduced to only 3.8%, 3.6% and 4.2% with 7.5mL/L EDA in the enzymatic hydrolysis of AFEX pretreated CS, washed EDA pretreated CS and CS cellulose.

Process design of SSCF for ethanol production from steam-pretreated, acetic-acid-impregnated wheat straw

BACKGROUND

Pretreatment is an important step in the production of ethanol from lignocellulosic material. Using acetic acid together with steam pretreatment allows the positive effects of an acid catalyst to be retained, while avoiding the negative environmental effects associated with sulphuric acid. Acetic acid is also formed during the pretreatment and hydrolysis of hemicellulose, and is a known inhibitor that may impair fermentation at high concentrations. The purpose of this study was to improve ethanol production from glucose and xylose in steam-pretreated, acetic-acid-impregnated wheat straw by process design of simultaneous saccharification and co-fermentation (SSCF), using a genetically modified pentose fermenting yeast strain Saccharomyces cerevisiae.

RESULTS

Ethanol was produced from glucose and xylose using both the liquid fraction and the whole slurry from pretreated materials. The highest ethanol concentration achieved was 37.5 g/L, corresponding to an overall ethanol yield of 0.32 g/g based on the glucose and xylose available in the pretreated material. To obtain this concentration, a slurry with a water-insoluble solids (WIS) content of 11.7 % was used, using a fed-batch SSCF strategy. A higher overall ethanol yield (0.36 g/g) was obtained at 10 % WIS.

CONCLUSIONS

Ethanol production from steam-pretreated, acetic-acid-impregnated wheat straw through SSCF with a pentose fermenting S. cerevisiae strain was successfully demonstrated. However, the ethanol concentration was too low and the residence time too long to be suitable for large-scale applications. It is hoped that further process design focusing on the enzymatic conversion of cellulose to glucose will allow the combination of acetic acid pretreatment and co-fermentation of glucose and xylose.

In situ detoxification of dry dilute acid pretreated corn stover by co-culture of xylose-utilizing and inhibitor-tolerant Saccharomyces cerevisiae increases ethanol production

Co-culture of xylose-utilizing and inhibitor-tolerant Saccharomyces cerevisiae was developed for bioethanol production from undetoxified pretreated biomass in simultaneously saccharification and co-fermentation (SSCF) process. Glucose accumulation during late fermentation phase in SSCF using xylose-utilizing strain can be eliminated by the introduction of inhibitor-tolerant strain. Effect of different ratios of two strains was investigated and xylose-utilizing strain to inhibitor-tolerant strain ratio of 10:1 (w/w) showed the best xylose consumption and the highest ethanol yield. Inoculating of xylose-utilizing strain at the later stage of SSCF (24-48h) exhibited lower ethanol yield than inoculating at early stage (the beginning 0-12h), probably due to the reduced enzymatic efficiency caused by the unconsumed xylose and oligomeric sugars. Co-culture SSCF increased ethanol concentration by 21.2% and 41.0% comparing to SSCF using individual inhibitor-tolerant and xylose-utilizing strain (increased from 48.5 and 41.7g/L to 58.8g/L), respectively, which suggest this co-culture system was very promising.

Towards efficient bioethanol production from agricultural and forestry residues: Exploration of unique natural microorganisms in combination with advanced strain engineering

Production of fuel ethanol from lignocellulosic feedstocks such as agricultural and forestry residues is receiving increasing attention due to the unsustainable supply of fossil fuels. Three key challenges include high cellulase production cost, toxicity of the cellulosic hydrolysate to microbial strains, and poor ability of fermenting microorganisms to utilize certain fermentable sugars in the hydrolysate. In this article, studies on searching of natural microbial strains for production of unique cellulase for biorefinery of agricultural and forestry wastes, as well as development of strains for improved cellulase production were reviewed. In addition, progress in the construction of yeast strains with improved stress tolerance and the capability to fully utilize xylose and glucose in the cellulosic hydrolysate was also summarized. With the superior microbial strains for high titer cellulase production and efficient utilization of all fermentable sugars in the hydrolysate, economic biofuels production from agricultural residues and forestry wastes can be realized.

Evaluation of soluble fraction and enzymatic residual fraction of dilute dry acid, ethylenediamine, and steam explosion pretreated corn stover on the enzymatic hydrolysis of cellulose

This study is aimed to examine the inhibition of soluble fraction (SF) and enzymatic residual fraction (ERF) in dry dilute acid (DDA), ethylenediamine (EDA) and steam explosion (SE) pretreated corn stover (CS) on the enzymatic digestibility of cellulose. SF of DDA, EDA and SE pretreated CS has high xylose, soluble lignin and xylo-oligomer content, respectively. SF of EDA pretreated CS leads to the highest inhibition, followed by SE and DDA pretreated CS. Inhibition of ERF of DDA and SE pretreated CS is higher than that of EDA pretreated CS. The inhibition degree (A0/A) of SF is 1.76 and 1.21 times to that of ERF for EDA and SE pretreated CS, respectively. The inhibition degree of ERF is 1.05 times to that of SF in DDA pretreated CS. The quantitative analysis shows that SF of EDA pretreated CS, SF and ERF of SE pretreated CS cause significant inhibition during enzymatic hydrolysis.

Enhanced Bioconversion of Cellobiose by Industrial Saccharomyces cerevisiae Used for Cellulose Utilization

Cellobiose accumulation and the compromised temperature for yeast fermentation are the main limiting factors of enzymatic hydrolysis process during simultaneous saccharification and fermentation (SSF). In this study, genes encoding cellobiose transporter and β-glucosidase were introduced into an industrial Saccharomyces cerevisiae strain, and evolution engineering was carried out to improve the cellobiose utilization of the engineered yeast strain. The evolved strain exhibited significantly higher cellobiose consumption rate (2.8-fold) and ethanol productivity (4.9-fold) compared with its parent strain. Besides, the evolved strain showed a high cellobiose consumption rate of 3.67 g/L/h at 34°C and 3.04 g/L/h at 38°C. Moreover, little cellobiose was accumulated during SSF of Avicel using the evolved strain at 38°C, and the ethanol yield from Avicel increased by 23% from 0.34 to 0.42 g ethanol/g cellulose. Overexpression of the genes encoding cellobiose transporter and β-glucosidase accelerated cellobiose utilization, and the improvement depended on the strain background. The results proved that fast cellobiose utilization enhanced ethanol production by reducing cellobiose accumulation during SSF at high temperature.

Heterologous xylose isomerase pathway and evolutionary engineering improve xylose utilization in Saccharomyces cerevisiae

Xylose utilization is one key issue for the bioconversion of lignocelluloses. It is a promising approach to engineering heterologous pathway for xylose utilization in Saccharomyces cerevisiae. Here, we constructed a xylose-fermenting yeast SyBE001 through combinatorial fine-tuning the expression of XylA and endogenous XKS1. Additional overexpression of genes RKI1, RPE1, TKL1, and TAL1 in the non-oxidative pentose phosphate pathway (PPP) in SyBE001 increased the xylose consumption rate by 1.19-fold. By repetitive adaptation, the xylose utilization rate was further increased by ∼10-fold in the resultant strain SyBE003. Gene expression analysis identified a variety of genes with significantly changed expression in the PPP, glycolysis and the tricarboxylic acid cycle in SyBE003.