Biological pretreatment of sugarcane bagasse with basidiomycetes producing varied patterns of biodegradation

Biocalorimetry-aided monitoring of fungal pretreatment of lignocellulosic agricultural residues

The present study aimed to investigate whether and how non-invasive biocalorimetric measurements could serve for process monitoring of fungal pretreatment during solid-state fermentation (SSF) of lignocellulosic agricultural residues such as wheat straw. Seven filamentous fungi representing different lignocellulose decay types were employed. Water-soluble sugars being immediately available after fungal pretreatment and those becoming water-extractable after enzymatic digestion of pretreated wheat straw with hydrolysing (hemi)cellulases were considered to constitute the total bioaccessible sugar fraction. The latter was used to indicate the success of pretreatments and linked to corresponding species-specific metabolic heat yield coefficients (YQ/X) derived from metabolic heat flux measurements during fungal wheat straw colonisation. An YQ/X range of about 120 to 140 kJ/g was seemingly optimal for pretreatment upon consideration of all investigated fungi and application of a non-linear Gaussian fitting model. Upon exclusion from analysis of the brown-rot basidiomycete Gloeophyllum trabeum, which differs from all other here investigated fungi in employing extracellular Fenton chemistry for lignocellulose decomposition, a linear relationship where amounts of total bioaccessible sugars were suggested to increase with increasing YQ/X values was obtained. It remains to be elucidated whether an YQ/X range being optimal for fungal pretreatment could firmly be established, or if the sugar accessibility for post-treatment generally increases with increasing YQ/X values as long as "conventional" enzymatic, i.e. (hemi)cellulase-based, lignocellulose decomposition mechanisms are operative. In any case, metabolic heat measurement-derived parameters such as YQ/X values may become very valuable tools supporting the assessment of the suitability of different fungal species for pretreatment of lignocellulosic substrates. KEY POINTS: • Biocalorimetry was used to monitor wheat straw pretreatment with seven filamentous fungi. • Metabolic heat yield coefficients (YQ/X) seem to indicate pretreatment success. • YQ/X values may support the selection of suitable fungal strains for pretreatment.

Dietary incorporation of brown seaweed spent oyster mushroom substrate alters growth performance, physiological responses and meat quality parameters in Boschveld roosters

Use of brown seaweed (Ecklonia maxima) as a nutraceutical source in indigenous chicken diets is limited by high dietary fibre levels. Inoculating seaweeds with oyster mushroom (Pleurotus ostreatus) spawn (OMS) could enhance the utility of the spent mushroom substrate (SMS). This study investigated the effect of feeding incremental levels of brown seaweed SMS on growth performance, physiological responses, and meat quality parameters in Boschveld roosters. A total of 324, 4-week-old Boschveld roosters were weighed and randomly allotted to 36 pens (9 birds per pen) to produce six replicates per dietary treatment. The diets were formulated as follows: a standard grower diet (CON); and CON containing 150 g/kg of brown seaweed inoculated with OMS at 0 (SMS0), 20 (SMS20), 30 (SMS30), 40 (SMS40) and 50% (SMS50). Birds fed diet CON had the least feed intake (p < 0.05) than all the other SMS treatment levels in weeks 7, 8, 12, 14 and 15. Diet SMS40 promoted higher (p < 0.05) body weight gain (BWG) than CON in weeks 6, 7, 9 and 14. Gain-to-feed ratio linearly increased in weeks 7 [R2 = 0.288; p = 0.010], 11 [R2 = 0.581, p = 0.0001] and 14 [R2 = 0.389, p = 0.004], respectively. Quadratic responses (p < 0.05) were observed for BWG in week 5, white blood cells, heterophils, platelets, lymphocytes, monocytes, and relative spleen and large intestine weights as OMS levels increased. Linear increases were recorded for slaughter [R2 = 0.197, p = 0.017] and breast weights [R2 = 0.197, p = 0.020] as OMS levels increased. Diet SMS0 promoted higher (p < 0.05) relative caeca weights than the CON and SMS treatment groups. Neither quadratic nor linear responses (p > 0.05) were observed for breast meat quality parameters. In conclusion, feeding brown seaweed SMS improved growth performance and slaughter weight, altered some blood parameters and internal organs, without affecting breast meat quality of Boschveld roosters. Based on the quadratic response for BWG, the optimum OMS level was deduced at 20% in a brown seaweed-based Boschveld rooster diet.

Fungal behavior and recent developments in biopulping technology

Biological pretreatment of wood chips by fungi is a well-known approach prior to mechanical- or chemical pulp production. For this biological approach, a limited number of white-rot fungi with an ability to colonize and selectively degrade lignin are used to pretreat wood chips allowing the remaining cellulose to be processed for further applications. Biopulping is an environmentally friendly technology that can reduce the energy consumption of traditional pulping processes. Fungal pretreatment also reduces the pitch content in the wood chips and improves the pulp quality in terms of brightness, strength, and bleachability. The bleached biopulps are easier to refine compared to pulps produced by conventional methodology. In the last decades, biopulping has been scaled up with pilot trials towards industrial level, with optimization of several intermediate steps and improvement of economic feasibility. Nevertheless, fundamental knowledge on the biochemical mechanisms involved in biopulping is still lacking. Overall, biopulping technology has advanced rapidly during recent decades and pilot mill trials have been implemented. The use of fungi as pretreatment for pulp production is in line with modern circular economy strategies and can be implemented in existing production plants. In this review, we discuss some recent advances in biopulping technology, which can improve mechanical-, chemical-, and organosolv pulping processes along with their mechanisms.

Efficient crop straws biotreatment using the fungus Cerrena Unicolor GC.u01

Lignin is main composition of agricultural biomass which can be decomposed through enzymatic hydrolysis by fungi. However, there are still needs to identify more efficient and effective fungal stain for biomass valorization. In this study, lignin degrading fungi from birch forest were screened for sustainable degradation of waste agricultural straws. The most effective strain was identified as Cerrena unicolor GC.u01 using 18 S rDNA gene-sequencing technology. Three different crop straws (corn stalk, rice and wheat straws) were used for the biotreatment studies. The activities of lignin degrading enzymes, laccase (Lac), cellulase and xylanase, secreted by C. unicolor were also determined. Scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analyzer (TGA) were further used to monitor the effects of the biotreatment process. The results showed that C. unicolor degraded 34.3% rice straw lignin, a percentage which was higher than other isolated strains after 15 d straw liquid fermentation. The highest Lac activity (8.396 U•mL- 1) was observed with corn stalk on the 7 d. Cellulase and xylanase activities, in the same biomass, were higher than those of wheat and rice straws after 15 d. Furthermore, SEM, FTIR and TGA analyses showed that C. unicolor pretreatment process had significant effects on corn stalk, rice and wheat straws' structures. The newly isolated stain of C. unicolor demonstrated high lignin degradation potential that can provide effective, ecofriendly means of valorizing biomass to industrial useable raw-material.

Green chemical and hybrid enzymatic pretreatments for lignocellulosic biorefineries: Mechanism and challenges

The greener chemical and enzymatic pretreatments for lignocellulosic biomasses are portraying a crucial role owing to their recalcitrant nature. Traditional pretreatments lead to partial degradation of lignin and hemicellulose moieties from the pretreated biomass. But it still restricts the enzyme accessibility for the digestibility towards the celluloses and the interaction of lignin-enzymes, nonproductively. Moreover, incursion of certain special chemical treatments and other lignin sulfonation techniques to the enzymatic pretreatment (hybrid enzymatic pretreatment) enhances the lignin structural modification, solubilization of the hemicelluloses and both saccharification and fermentation processes (SAF). This article concentrates on recent developments in various chemical and hybrid enzymatic pretreatments on biomass materials with their mode of activities. Furthermore, the issues on strategies of the existing pretreatments towards their industrial applications are highlighted, which could lead to innovative ideas to overcome the challenges and give guideline for the researchers towards the lignocellulosic biorefineries.

Organosolv pretreatment: an in-depth purview of mechanics of the system

The concept of biorefinery has been advancing globally and organosolv pretreatment strategy has seen an upsurge in research due to its efficiency in removing the recalcitrant lignin and dissolution of cellulose. The high-performance organosolv system uses green solvents and its reusability contributes concurrently to the biorefinery sector and sustainability. The major advantage of the current system involves the continuous removal of lignin to enhance cellulose accessibility, thereby easing the later biorefinery steps, which were immensely restricted due to the recalcitrant lignin. The current system process can be further explored and enhanced via the amalgamation of new technologies, which is still a work in progress. Thus, the current review summarizes organosolv pretreatment and the range of solvents used, along with a detailed mechanistic approach that results in efficient pretreatment of LCB. The latest developments for designing high-performance pretreatment systems, their pitfalls, and advanced assessments such as Life Cycle Assessment along with Techno-Economic Assessment have also been deliberated to allow an insight into its diverse potential applicability towards a sustainable future.

Different pre-treatments and kinetic models for bioethanol production from lignocellulosic biomass: A review

Lignocellulosic biomass is the generally explored substrate to produce bioethanol for environmental sustainability due to its availability in abundance. However, the complex network of cellulose-hemicellulose-lignin present in it makes its hydrolysis as a challenging task. To boost the effectiveness of conversion, biomass is pre-treated before enzymatic hydrolysis to alter or destroy its original composition. Enzymes like Cellulases are widely used for breaking down cellulose into fermentable sugars. Enzymatic hydrolysis is a complex process involving many influencing factors such as pH, temperature, substrate concentration. This review presents major four pre-treatment methods used for hydrolysing different substrates under varied reaction conditions along with their mechanism and limitations. A relative comparison of data analysis for most widely studied 10 kinetic models is briefly explained in terms of substrates used to get the brief insight about hydrolysis rates. The summary of pre-treatment methods and hydrolysis rates including cellulase enzyme kinetics will be the value addition for upcoming researchers for optimising the hydrolysis process.

Sugarcane wastes as microbial feedstocks: A review of the biorefinery framework from resource recovery to production of value-added products

Sugarcane industry is a major agricultural sector capable of producing sugars with byproducts including straw, bagasse, and molasses. Sugarcane byproducts are no longer wastes since they can be converted into carbon-rich resources for biorefinery if pretreatment of these is well established. Considerable efforts have been devoted to effective pretreatment techniques for each sugarcane byproduct to supply feedstocks in microbial fermentation to produce value-added fuels, chemicals, and polymers. These value-added chains, which start with low-value industrial wastes and end with high-value products, can make sugarcane-based biorefinery a more viable option for the modern chemical industry. In this review, recent advances in sugarcane valorization techniques are presented, ranging from sugarcane processing, pretreatment, and microbial production of value-added products. Three lucrative products, ethanol, 2,3-butanediol, and polyhydroxyalkanoates, whose production from sugarcane wastes has been widely researched, are being explored. Future studies and development in sugarcane waste biorefinery are discussed to overcome the challenges remaining.

Membrane Bioreactors: A Promising Approach to Enhanced Enzymatic Hydrolysis of Cellulose

The depletion of fossil fuel resources and the negative impact of their use on the climate have resulted in the need for alternative sources of clean, sustainable energy. One available alternative, bioethanol, is a potential substitute for, or additive to, petroleum-derived gasoline. In the lignocellulose-to-bioethanol process, the cellulose hydrolysis step represents a major hurdle that hinders commercialization. To achieve economical production of bioethanol from lignocellulosic materials, the rate and yield of the enzymatic hydrolysis of cellulose, which is preferred over other chemically catalyzed processes, must be enhanced. To achieve this, product inhibition and enzyme loss, which are two major challenges, must be overcome. The implementation of membranes, which can permeate molecules selectively based on their size, offers a solution to this problem. Membrane bioreactors (MBRs) can enhance enzymatic hydrolysis yields and lower costs by retaining enzymes for repeated usage while permeating the products. This paper presents a critical discussion of the use of MBRs as a promising approach to the enhanced enzymatic hydrolysis of cellulosic materials. Various MBR configurations and factors that affect their performance are presented.

Use of carbohydrate-directed enzymes for the potential exploitation of sugarcane bagasse to obtain value-added biotechnological products

Microorganisms, such as fungi and bacteria, are crucial players in the production of enzymatic cocktails for biomass hydrolysis or the bioconversion of plant biomass into products with industrial relevance. The biotechnology industry can exploit lignocellulosic biomass for the production of high-value chemicals. The generation of biotechnological products from lignocellulosic feedstock presents several bottlenecks, including low efficiency of enzymatic hydrolysis, high cost of enzymes, and limitations on microbe metabolic performance. Genetic engineering offers a route for developing improved microbial strains for biotechnological applications in high-value product biosynthesis. Sugarcane bagasse, for example, is an agro-industrial waste that is abundantly produced in sugar and first-generation processing plants. Here, we review the potential conversion of its feedstock into relevant industrial products via microbial production and discuss the advances that have been made in improving strains for biotechnological applications.

Sugarcane bagasse into value-added products: a review

Strategic valorization of readily available sugarcane bagasse (SB) is very important for waste management and sustainable biorefinery. Conventional SB pretreatment methods are ineffective to meet the requirement for industrial adaptation. Several past studies have highlighted different pretreatment procedures which are lacking environmentally benign characteristics and effective SB bioconversion. This article provides an in-depth review of a variety of environmentally acceptable thermochemical and biological pretreatment techniques for SB. Advancements in the conversion processes such as pyrolysis, liquefaction, gasification, cogeneration, lignin conversion, and cellulose conversion via fermentation processes are critically reviewed for the formation of an extensive array of industrially relevant products such as biofuels, bioelectricity, bioplastics, bio adsorbents, and organic acids. This article would provide comprehensive insights into several crucial aspects of thermochemical and biological conversion processes, including systematic perceptions and scientific developments for value-added products from SB valorization. Moreover, it would lead to determining efficient pretreatment and/or conversion processes for sustainable development of industrial-scale sugarcane-based biorefinery.

Effect of solid-state fermentation and ultrasonication processes on antimicrobial and antioxidant properties of algae extracts

Algal biomass (AB) is prospective source of valuable compounds, however, Baltic Sea macroalgae have some challenges, because of their high microbial and chemical contamination. These problems can be solved, by using appropriate technologies for AG pre-treatment. The aim of this study was to evaluate the influence of two pre-treatments, solid-state fermentation with the Lactiplantibacillus plantarum LUHS135 and ultrasonication, on the antioxidant and antimicrobial characteristics of macro- (Cladophora rupestris, Cladophora glomerata, Furcellaria lumbricalis, Ulva intestinalis) and Spirulina (Arthrospira platensis) extracts. Also, combinations of extracts and LUHS135 were developed and their characteristics were evaluated. The total phenolic compound content was determined from the calibration curve and expressed in mg of gallic acid equivalents; antioxidant activity was measured by a Trolox equivalent antioxidant capacity assay using the DPPH^• (1,1-diphenyl-2-picrylhydrazyl), ABTS^•+ 2,2′-azinobis-(3-ethylbenzothiazoline-6-sulfonic acid), FRAP (Ferric Reducing Ability of Plasma) discoloration methods. Antimicrobial activity was measured by using agar well diffusion assay and in a liquid medium. The highest DPPH^• and ABTS^•+ was shown by C.rupestris and F.lumbricalis extract × LUHS135 combinations, the highest FRAP - by non-pretreated C.rupestris and F.lumbricalis extract × LUHS135 combinations. Ultrasonicated samples inhibited four out of seven tested pathogens. Finally, the tested pre-treatments showed good perspectives and can be recommended for AB valorization.

A consolidated review of commercial-scale high-value products from lignocellulosic biomass

For decades, lignocellulosic biomass has been introduced to the public as the most important raw material for the environmentally and economically sustainable production of high-valued bioproducts by microorganisms. However, due to the strong recalcitrant structure, the lignocellulosic materials have major limitations to obtain fermentable sugars for transformation into value-added products, e.g., bioethanol, biobutanol, biohydrogen, etc. In this review, we analyzed the recent trends in bioenergy production from pretreated lignocellulose, with special attention to the new strategies for overcoming pretreatment barriers. In addition, persistent challenges in developing for low-cost advanced processing technologies are also pointed out, illustrating new approaches to addressing the global energy crisis and climate change caused by the use of fossil fuels. The insights given in this study will enable a better understanding of current processes and facilitate further development on lignocellulosic bioenergy production.

Ultrasonic-Assisted Dual-Alkali Pretreatment and Enzymatic Hydrolysis of Sugarcane Bagasse Followed by Candida tropicalis Fermentation to Produce Xylitol

In this work, the investigation mainly focused on ultrasonic-assisted dual-alkali pretreatment and enzymatic hydrolysis of sugarcane bagasse followed by Candida tropicalis fermentation to produce xylitol. The results showed that the combination of NaOH and ammonia water had the best effect by comparing the effects of the four single-alkali (NaOH, KOH, ammonia water, Ca(OH)₂) and their mixed double-alkali pretreatments on xylose content. Then, the optimal conditions for ultrasonic-assisted pretreatment and enzymatic hydrolysis of sugarcane bagasse were obtained by response surface methodology. When the ratio of NaOH and ammonia water was 2:1, the mixed alkali concentration (v/v) was 17%, the ultrasonic temperature was 45°C, the ultrasonic power was 300 W, and the ultrasonic time was 40 min, the content of xylose reached a maximum of 2.431 g/L. Scanning electron microscopy showed that sugarcane bagasse by ultrasonic-assisted alkali pretreatment aggravated with more folds and furrows. Moreover, the fermentation results showed that the concentration ratio of enzymatic hydrolysate of sugarcane bagasse affected the xylitol yield, and when concentrated three times, the highest yield of xylitol (54.42%) was obtained.

Sequential fungal pretreatment of unsterilized Miscanthus: changes in composition, cellulose digestibility and microbial communities

A sequential fungal pretreatment of Miscanthus × giganteus was conducted by mixing unsterilized Miscanthus with material previously colonized with the white-rot fungus Ceriporiopsis subvermispora. For three generations, each generation started with inoculation by mixing unsterilized fresh Miscanthus with end material from the previous generation and ended after 28 days of incubation at 28 °C. After the first generation, the cellulose digestibility of the material doubled, compared to that of the unsterilized Miscanthus, but the second and third generations showed no enhancements in cellulose digestibility. Furthermore, high degradation of Miscanthus structural carbohydrates occurred during the first generation. A microbial community study showed that, even though the fungal community of the material previously colonized by C. subvermispora was composed mainly of this fungus (> 99%), by the first generation its relative abundance was down to only 9%, and other microbes had prevailed. Additionally, changes in the bacterial community occurred that might be associated with unwanted cellulose degradation in the system. This reiterates the necessity of feedstock microbial load reduction for the stability and reproducibility of fungal pretreatment of lignocellulosic biomass. KEY POINTS: • Sequential fungal pretreatment of unsterilized Miscanthus was unsuccessful. • Feedstock changes with white-rot fungi favored the growth of other microorganisms. • Feedstock microbial reduction is necessary for pretreatment with C. subvermispora.

Laccase-mediated delignification and detoxification of lignocellulosic biomass: removing obstacles in energy generation

The rising global population and worldwide industrialization have led to unprecedented energy demand that is causing fast depletion of fossil reserves. This has led to search for alternative energy sources that are renewable and environment friendly. Use of lignocellulosic biomass for energy generation is considered a promising approach as it does not compete with food supply. However, the lignin component of the biomass acts as a natural barrier that prevents its efficient utilization. In order to remove the lignin and increase the amount of fermentable sugars, the lignocellulosic biomass is pretreated using physical and chemical methods which are costly and hazardous for environment. Moreover, during the traditional pretreatment process, numerous inhibitory compounds are generated that adversely affect the growth of fermentative microbes. Alternatively, biological methods that use microbes and their enzymes disrupt lignin polymers and increase the accessibility of the carbohydrates for the sugar generation. Microbial laccases have been considered as an efficient biocatalyst for delignification and detoxification offering a green initiative for energy generation process. The present review aims to bring together recent studies in bioenergy generation using laccase biocatalyst in the pretreatment processes. The work provides an overview of the sustainable and eco-friendly approach of biological delignification and detoxification through whole-cell and enzymatic methods, use of laccase-mediator system, and immobilized laccases for this purpose. It also summarizes the advantages, associated challenges, and potential prospects to overcome the limitations.

A comprehensive study of the promoting effect of manganese on white rot fungal treatment for enzymatic hydrolysis of woody and grass lignocellulose

BACKGROUND

The efficiency of biological systems as an option for pretreating lignocellulosic biomass has to be improved to make the process practical. Fungal treatment with manganese (Mn) addition for improving lignocellulosic biomass fractionation and enzyme accessibility were investigated in this study. The broad-spectrum effect was tested on two different types of feedstocks with three fungal species. Since the physicochemical and structural properties of biomass were the main changes caused by fungal degradation, detailed characterization of biomass structural features was conducted to understand the mechanism of Mn-enhanced biomass saccharification.

RESULTS

The glucose yields of fungal-treated poplar and wheat straw increased by 2.97- and 5.71-fold, respectively, after Mn addition. Particularly, over 90% of glucose yield was achieved in Mn-assisted Pleurotus ostreatus-treated wheat straw. A comparison study using pyrolysis gas chromatography mass spectrometry (Py-GC/MS) and two-dimensional 1H-13C heteronuclear single quantum coherence (2D HSQC) nuclear magnetic resonance (NMR) spectroscopy was conducted to elucidate the role of Mn addition on fungal disruption of the cross-linked structure of whole plant cell wall. The increased Cα-oxidized products was consistent with the enhanced cleavage of the major β-O-4 ether linkages in poplar and wheat straw lignin or in the wheat straw lignin-carbohydrate complexes (LCCs), which led to the reduced condensation degree in lignin and decreased lignin content in Mn-assisted fungal-treated biomass. The correlation analysis and principal component analysis (PCA) further demonstrated that Mn addition to fungal treatment enhanced bond cleavage in lignin, especially the β-O-4 ether linkage cleavage played the dominant role in removing the biomass recalcitrance and contributing to the glucose yield enhancement. Meanwhile, enhanced deconstruction of LCCs was important in reducing wheat straw recalcitrance. The findings provided not only mechanistic insights into the Mn-enhanced biomass digestibility by fungus, but also a strategy for improving biological pretreatment efficiency of lignocellulose.

CONCLUSION

The mechanism of enhanced saccharification of biomass by Mn-assisted fungal treatment mainly through Cα-oxidative cleavage of β-O-4 ether linkages further led to the decreased condensation degree in lignin, as a result, biomass recalcitrance was significantly reduced by Mn addition.

Greener Pretreatment Approaches for the Valorisation of Natural Fibre Biomass into Bioproducts

The utilization of lignocellulosic biomass in various applications has a promising potential as advanced technology progresses due to its renowned advantages as cheap and abundant feedstock. The main drawback in the utilization of this type of biomass is the essential requirement for the pretreatment process. The most common pretreatment process applied is chemical pretreatment. However, it is a non-eco-friendly process. Therefore, this review aims to bring into light several greener pretreatment processes as an alternative approach for the current chemical pretreatment. The main processes for each physical and biological pretreatment process are reviewed and highlighted. Additionally, recent advances in the effect of different non-chemical pretreatment approaches for the natural fibres are also critically discussed with a focus on bioproducts conversion.

Needleless electrospun phytochemicals encapsulated nanofibre based 3-ply biodegradable mask for combating COVID-19 pandemic

The emergence of COVID-19 pandemic has severely affected human health and world economies. According to WHO guidelines, continuous use of face mask is mandatory for personal protection for restricting the spread of bacteria and virus. Here, we report a 3-ply cotton-PLA-cotton layered biodegradable face-mask containing encapsulated phytochemicals in the inner-filtration layer. The nano-fibrous PLA filtration layer was fabricated using needleless electrospinning of PLA & phytochemical-based herbal-extracts. This 3-layred face mask exhibits enhanced air permeability with a differential pressure of 35.78 Pa/cm² and superior bacterial filtration efficiency of 97.9% compared to conventional face masks. Close-packed mesh structure of the nano-fibrous mat results in effective adsorption of particulate matter, aerosol particles, and bacterial targets deep inside the filtration layer. The outer hydrophobic layer of mask exhibited effective blood splash resistance up to a distance of 30 cm, ensuring its utilization for medical practices. Computational analysis of constituent phytochemicals using the LibDock algorithm predicted inhibitory activity of chemicals against the protein structured bacterial sites. The computational analysis projected superior performance of phytochemicals considering the presence of stearic acid, oleic acid, linoleic acid, and Arachidic acid exhibiting structural complementarity to inhibit targeted bacterial interface. Natural cotton fibers and PLA bio-polymer demonstrated promising biodegradable characteristics in the presence of in-house cow-dung based biodegradation slurry. Addition of jaggery to the slurry elevated the biodegradation performance, resulting in increment of change of weight from 07% to 12%. The improved performance was attributed to the increased sucrose content in biodegradation slurry, elevating the bacterial growth in the slurry. An innovative face mask has shown promising results for utilization in day-to-day life and medical frontline workers, considering the post-pandemic environmental impacts.

Cultivating oyster mushrooms on red grape pomace waste enhances potential nutritional value of the spent substrate for ruminants

The use of red grape pomace (GP; Vitis vinifera L. var. Shiraz) as a source of beneficial bioactive compounds in ruminant diets is limited by high levels of indigestible compounds in the grape skin matrix. This problem demands innovative, inexpensive, and easy-to-use strategies that improve the digestibility of GP. The bioconversion of GP using edible oyster mushrooms (Pleurotus ostreatus) is one such strategy that has not been previously explored. Therefore, this study evaluated the effect of cultivating oyster mushrooms on GP on chemical composition and in vitro ruminal fermentation parameters of the spent mushroom substrate. The GP was inoculated with oyster mushroom spawns at 0, 200, 300, 400, or 500 g/kg, and incubated for 4 weeks. Organic matter, acid detergent lignin, sodium, manganese, cobalt, and copper linearly declined (P < 0.05) as spawn rates increased. A quadratic trend was observed for crude protein, neutral detergent fibre, acid detergent fibre, magnesium, phosphorus, and calcium content in response to increasing spawn rates. Higher spawning rates (20–50%) had a positive effect (P < 0.05) on gas production from the immediately fermentable fraction (a), rate of gas production from the slowly fermentable fraction (c) and effective gas production. However, gas production from the slowly fermentable fraction (b) and potential gas production linearly declined in response to increasing spawning rates. There was a linear increase (P < 0.05) in the immediately degradable fraction (a), while quadratic effects were observed for partition factors, effective degradability, and in vitro organic matter degradability at 48 h in response to spawning rates. It can be concluded that inoculating GP with oyster mushroom spawn reduced fibre content while increasing crude protein content and in vitro ruminal fermentation efficiency of red grape pomace. Based on the quadratic responses of partition factors at 48 hours post-inoculation, the optimum spawning rate for maximum ruminal fermentation efficiency of GP was determined to be 300 g/kg.

Cellulosic and hemicellulosic fractions of sugarcane bagasse: Potential, challenges and future perspective

Sugarcane bagasse is a rich source of cellulose (32-45%), hemicellulose (20-32%) and lignin (17-32%), 1.0-9.0% ash and some extractives. Huge amount of the generation of sugarcane bagasse has been a great challenge to industries and environment at global level for many years. Though cellulosic and hemicellulosic fractions in bagasse makes it a potential raw substrate for the production of value-added products at large scale, the presence of lignin hampers its saccharification which further leads to low yields of the value-added products. Therefore, an appropriate pretreatment strategy is of utmost importance that effectively solubilizes the lignin that exposes cellulose and hemicellulose for enzymatic action. Pretreatment also reduces the biomass recalcitrance i.e., cellulose crystallinity, structural complexity of cell wall and lignification for its effective utilization in biorefinery. Sugarcane bagasse served as nutrient medium for the cultivation of diverse microorganisms for the production of industrially important metabolites including enzymes, reducing sugars, prebiotic, organic acids and biofuels. Sugarcane bagasse has been utilized in the generation of electricity, syngas and as biosorbant in the bioremediation of heavy metals. Furthermore, the ash generated from bagasse is an excellent source for the synthesis of high strength and light weight bricks and tiles. Present review describes the utility of sugarcane bagasse as sustainable and renewable lignocellulosic substrate for the production of industrially important multifarious value-added products.

Microorganisms and Enzymes Used in the Biological Pretreatment of the Substrate to Enhance Biogas Production: A Review

The pretreatment of lignocellulosic biomass (LC biomass) prior to the anaerobic digestion (AD) process is a mandatory step to improve feedstock biodegradability and biogas production. An important potential is provided by lignocellulosic materials since lignocellulose represents a major source for biogas production, thus contributing to the environmental sustainability. The main limitation of LC biomass for use is its resistant structure. Lately, biological pretreatment (BP) gained popularity because they are eco-friendly methods that do not require chemical or energy input. A large number of bacteria and fungi possess great ability to convert high molecular weight compounds from the substrate into lower mass compounds due to the synthesis of microbial extracellular enzymes. Microbial strains isolated from various sources are used singly or in combination to break down the recalcitrant polymeric structures and thus increase biogasgeneration. Enzymatic treatment of LC biomass depends mainly on enzymes like hemicellulases and cellulases generated by microorganisms. The articles main purpose is to provide an overview regarding the enzymatic/biological pretreatment as one of the most potent techniques for enhancing biogas production.

High-potency white-rot fungal strains and duration of fermentation to optimize corn straw as ruminant feed

Five white-rot fungi Pleurotus ostreatus, Lentinus edodes, Hericium erinaceus, Pleurotus eryngii and Flammulina filiformis were studied (solid-state incubation and in vitro gas production) to determine lignin degradation and optimal duration of fermentation of corn straw. All fungi significantly decreased lignin, with optimal reductions after 28 d. Although cellulose also decreased, L. edodes and P. eryngii minimized these losses. In intro dry matter digestibility, total volatile fatty acid concentration and total gas production of fermented corn straw decreased (P < 0.001) as fermentation was prolonged, with improved rumen fermentability for all fungal treatments except F. filiformis. Total gas production in L. edodes did not decrease but peaked on day 28, whereas F. filiformis reduced methane emission. In conclusion, fermentation of corn straw with P. eryngii or L. edodes for 28 d degraded lignin and improved nutritional value as ruminant feed.

The Secretome of Phanerochaete chrysosporium and Trametes versicolor Grown in Microcrystalline Cellulose and Use of the Enzymes for Hydrolysis of Lignocellulosic Materials

The ability of white-rot fungi to degrade polysaccharides in lignified plant cell walls makes them a suitable reservoir for CAZyme prospects. However, to date, CAZymes from these species are barely studied, which limits their use in the set of choices for biomass conversion in modern biorefineries. The current work joined secretome studies of two representative white-rot fungi, Phanerochaete chrysosporium and Trametes versicolor, with expression analysis of cellobiohydrolase (CBH) genes, and use of the secretomes to evaluate enzymatic conversion of simple and complex sugarcane-derived substrates. Avicel was used to induce secretion of high levels of CBHs in the extracellular medium. A total of 56 and 58 proteins were identified in cultures of P. chrysosporium and T. versicolor, respectively, with 78-86% of these proteins corresponding to plant cell wall degrading enzymes (cellulolytic, hemicellulolytic, pectinolytic, esterase, and auxiliary activity). CBHI predominated among the plant cell wall degrading enzymes, corresponding to 47 and 34% of the detected proteins in P. chrysosporium and T. versicolor, respectively, which confirms that Avicel is an efficient CBH inducer in white-rot fungi. The induction by Avicel of genes encoding CBHs (cel) was supported by high expression levels of cel7D and cel7C in P. chrysosporium and T. versicolor, respectively. Both white-rot fungi secretomes enabled hydrolysis experiments at 10 FPU/g substrate, despite the varied proportions of CBHs and other enzymes present in each case. When low recalcitrance sugarcane pith was used as a substrate, P. chrysosporium and T. versicolor secretomes performed similarly to Cellic® CTec2. However, the white-rot fungi secretomes were less efficient than Cellic® CTec2 during hydrolysis of more recalcitrant substrates, such as acid or alkaline sulfite-pretreated sugarcane bagasse, likely because Cellic® CTec2 contains an excess of CBHs compared with the white-rot fungi secretomes. General comparison of the white-rot fungi secretomes highlighted T. versicolor enzymes for providing high glucan conversions, even at lower proportion of CBHs, probably because the other enzymes present in this secretome and CBHs lacking carbohydrate-binding modules compensate for problems associated with unproductive binding to lignin.

Recent advances in the pretreatment of microalgal and lignocellulosic biomass: A comprehensive review

Microalgal and lignocellulosic biomass is the most sumptuous renewable bioresource raw material existing on earth. Recently, the bioconversion of biomass into biofuels have received significant attention replacing fossil fuels. Pretreatment of biomass is a critical process in the conversion due to the nature and structure of the biomass cell wall that is complex. Although green technologies for biofuel production are advancing, the productivity and yield from these techniques are low. Over the past years, various pretreatment techniques have been developed and successfully employed to improve the technology. This paper presents an in-depth review of the recent advancement of pretreatment methods focusing on microalgal and lignocellulosic biomass. The technological approaches involving physical, chemical, biological and other latest pretreatment methods are reviewed.

Fungal Laccase Production from Lignocellulosic Agricultural Wastes by Solid-State Fermentation: A Review

Laccases are copper-containing oxidase enzymes found in many fungi. They have received increasing research attention because of their broad substrate specificity and applicability in industrial processes, such as pulp delignification, textile bleaching, phenolic removal, and biosensors. In comparison with traditional submerged fermentation (SF), solid-state fermentation (SSF) is a simpler technique for laccase production and has many advantages, including higher productivity, efficiency, and enzyme stability as well as reduced production costs and environmental pollution. Here, we review recent advances in laccase production technology, with focus on the following areas: (i) Characteristics and advantages of lignocellulosic agricultural wastes used as SSF substrates of laccase production, including detailed suggestions for the selection of lignocellulosic agricultural wastes; (ii) Comparison of fungal laccase production from lignocellulosic substrates by either SSF or SF; (iii) Fungal performance and strain screening in laccase production from lignocellulosic agricultural wastes by SSF; (iv) Applications of laccase production under SSF; and (v) Suggestions and avenues for future studies of laccase production by fungal SSF with lignocellulosic materials and its applications.

The secretome of two representative lignocellulose-decay basidiomycetes growing on sugarcane bagasse solid-state cultures

Secretome evaluations of lignocellulose-decay basidiomycetes can reveal new enzymes in selected fungal species that degrade specific substrates. Proteins discovered in such studies can support biorefinery development. Brown-rot (Gloeophyllum trabeum) and white-rot (Pleurotus ostreatus) fungi growing in sugarcane bagasse solid-state cultures produced 119 and 63 different extracellular proteins, respectively. Several of the identified enzymes are suitable for in vitro biomass conversion, including a range of cellulases (endoglucanases, cellobiohydrolases and β-glucosidases), hemicellulases (endoxylanases, α-arabinofuranosidases, α-glucuronidases and acetylxylan esterases) and carbohydrate-active auxiliary proteins, such as AA9 lytic polysaccharide monooxygenase, AA1 laccase and AA2 versatile peroxidase. Extracellular oxalate decarboxylase was also detected in both fungal species, exclusively in media containing sugarcane bagasse. Interestingly, intracellular AA6 quinone oxidoreductases were also exclusively produced under sugarcane bagasse induction in both fungi. These enzymes promote quinone redox cycling, which is used to produce Fenton's reagents by lignocellulose-decay fungi. Hitherto undiscovered hypothetical proteins that are predicted in lignocellulose-decay fungi genomes appeared in high relative abundance in the cultures containing sugarcane bagasse, which suggests undisclosed, new biochemical mechanisms that are used by lignocellulose-decay fungi to degrade sugarcane biomass. In general, lignocellulose-decay fungi produce a number of canonical hydrolases, as well as some newly observed enzymes, that are suitable for in vitro biomass digestion in a biorefinery context.

Modification of corn stover for improving biodegradability and anaerobic digestion performance by Ceriporiopsis subvermispora

Ceriporiopsis subvermispora was used to modify corn stover for improving the biodegradability and biomethane yield. Corn stover was incubated with C. subvermispora for 5-90 days then anaerobically digested. It was found that the corn stover modified for 15 days achieved the highest biomethane yield of 235 mL·g^-1 VS, which was an increase of 15.2% over that of the non-modified one. The mechanism analyses indicated that the improvement resulted from the combined roles of degradation selectivity, destruction of lignocellulosic structures, and linkages. The analyses showed that C. subvermispora has a high relative selectivity of lignin degradation. The structure of the lignin and the linkages among lignin and hemicellulose and cellulose were broken obviously by acetyl group removal, and the enzymatic hydrolysis of cellulose was increased by 35.61%. The finding indicated that C. subvermispora modification is one of the effective methods for enhancing biomethane yield of corn stover.

Techno-Economic Bottlenecks of the Fungal Pretreatment of Lignocellulosic Biomass

Fungal pretreatment is a biological process that uses rotting fungi to reduce the recalcitrance and enhance the enzymatic digestibility of lignocellulosic feedstocks at low temperature, without added chemicals and wastewater generation. Thus, it has been presumed to be low cost. However, fungal pretreatment requires longer incubation times and generates lower yields than traditional pretreatments. Thus, this study assesses the techno-economic feasibility of a fungal pretreatment facility for the production of fermentable sugars for a 75,700 m3 (20 million gallons) per year cellulosic bioethanol plant. Four feedstocks were evaluated: perennial grasses, corn stover, agricultural residues other than corn stover, and hardwood. The lowest estimated sugars production cost ($1.6/kg) was obtained from corn stover, and was 4–15 times as much as previous estimates for conventional pretreatment technologies. The facility-related cost was the major contributor (46–51%) to the sugar production cost, mainly because of the requirement of large equipment in high quantities, due to process bottlenecks such as low sugar yields, low feedstock bulk density, long fungal pretreatment times, and sterilization requirements. At the current state of the technology, fungal pretreatment at biorefinery scale does not appear to be economically feasible, and considerable process improvements are still required to achieve product cost targets.

Proteomic researches for lignocellulose-degrading enzymes: A mini-review

Protective action of lignin/hemicellulose networks and crystalline structures of embedded cellulose render lignocellulose material resistant to external enzymatic attack. To eliminate this bottleneck, research has been conducted in which advanced proteomic techniques are applied to identify effective commercial hydrolytic enzymes. This mini-review summarizes researches on lignocellulose-degrading enzymes, the mechanisms of the responses of various lignocellulose-degrading strains and microbial communities to various carbon sources and various biomass substrates, post-translational modifications of lignocellulose-degrading enzymes, new lignocellulose-degrading strains, new lignocellulose-degrading enzymes and a new method of secretome analysis. The challenges in the practical use of enzymatic hydrolysis process to realize lignocellulose biorefineries are discussed, along with the prospects for the same.

Sequential white-rot and brown-rot fungal pretreatment of wheat straw as a promising alternative for complementary mild treatments

White-rot and brown-rot fungi have complementary mechanisms to selectively degrade lignin and holocellullose, respectively. Thereby, a fungal co-culture of a white-rot and a brown-rot fungal could result in efficient strategy for a mild lignocellulosic biomass pretreatment. In this work, single, sequential and co-inoculation of the selective-lignin degrading white-rot fungus Ganoderma lobatum and the brown-rot fungus Gloeophyllum trabeum were evaluated as biological pretreatments of wheat straw to enhance enzymatic hydrolysis of cellulose. The single cultures of G. lobatum and G. trabeum exhibited preferential degradation of lignin and hemicellulose, respectively. The total crystallinity index decreased in samples pretreated with G. trabeum but not with G. lobatum. The pretreatment with single cultures of G. lobatum or G. trabeum increased glucose yields by 43.6% and 26.1% respectively compared to untreated straw. Although co-inoculation resulted in higher yields of glucose when compared with single cultures, only a slight synergistic effect between fungi was observed. Contrary, the sequential inoculation of G. lobatum incubated for 10 days followed by G. trabeum incubated for 10 days more showed a strong synergic effect on enzymatic hydrolysis. This sequential culture showed the highest glucose yield (191.5 mg g^-1 wheat straw), 2.8-fold higher than untreated wheat straw, and 140-150% higher than the single-cultures of G. lobatum and G. trabeum, respectively.

Enhancing bioethanol production from water hyacinth by new combined pretreatment methods

This study investigated the possibility of enhancing bioethanol production by combined pretreatment methods for water hyacinth. Three different kinds of pretreatment methods, including microbial pretreatment, microbial combined dilute acid pretreatment, and microbial combined dilute alkaline pretreatment, were investigated for water hyacinth degradation. The results showed that microbial combined dilute acid pretreatment is the most effective method, resulting in the highest cellulose content (39.4 ± 2.8%) and reducing sugars production (430.66 mg·g^-1). Scanning Electron Microscopy and Fourier Transform Infrared Spectrometer analysis indicated that the basic tissue of water hyacinth was significantly destroyed. Compared to the other previously reported pretreatment methods for water hyacinth, which did not append additional cellulase and microbes for hydrolysis process, the microbial combined dilute acid pretreatment of our research could achieve the highest reducing sugars. Moreover, the production of bioethanol could achieve 1.40 g·L^-1 after fermentation, which could provide an extremely promising way for utilization of water hyacinth.

Degradation of lignin in birch sawdust treated by a novel Myrothecium verrucaria coupled with ultrasound assistance

Combined treatment of a novel fungal endophyte Myrothecium verrucaria coupled with ultrasound assistance was conducted to enhance lignin degradation in birch sawdust. The optimum treatment conditions were confirmed as the materials to liquid ratio 1:20, temperature 30°C, time 4days and pH 7, respectively. The results showed that the combined treatment led to the lignin degradation reaching 67.95±2.14%, while the lignin degradation were 45.50±2.12% and 13.75±0.66% with separate fungal treatment and ultrasound treatment, respectively. Moreover, SEM and FTIR analysis indicated that combined treatment significantly altered surface morphology and chemical structure of birch sawdust. The combined treatment greatly increased lignin removal during short time in mild environment. Therefore, these results demonstrated that the combined treatment of fungal endophyte coupled with ultrasound assistance has the high potential for the removal lignin in lignocellulose.

A novel and efficient fungal delignification strategy based on versatile peroxidase for lignocellulose bioconversion

BACKGROUND

The selective lignin-degrading white-rot fungi are regarded to be the best lignin degraders and have been widely used for reducing the saccharification recalcitrance of lignocellulose. However, the biological delignification and conversion of lignocellulose in biorefinery is still limited. It is necessary to develop novel and more efficient bio-delignification systems.

RESULTS

Physisporinus vitreus relies on a new versatile peroxidase (VP)-based delignification strategy to remove enzymatic recalcitrance of corn stover efficiently, so that saccharification of corn stover was significantly enhanced to 349.1 mg/g biomass (yield of glucose) and 91.5% (hydrolysis yield of cellulose) at 28 days, as high as levels reached by thermochemical treatment. Analysis of the lignin structure using pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS) showed that the total abundance of lignin-derived compounds decreased by 54.0% and revealed a notable demethylation during lignin degradation by P. vitreus. Monomeric and dimeric lignin model compounds were used to confirm the ligninolytic capabilities of extracellular ligninases secreted by P. vitreus. The laccase (Lac) from P. vitreus could not oxidize nonphenolic lignin compounds and polymerized β-O-4 and 5-5' dimers to precipitate which had a negative effect on the enzymatic hydrolysis of corn stover in vitro. However, the VP from P. vitreus could oxidize both phenolic and nonphenolic lignin model compounds as well as break the β-O-4 and 5-5' dimers into monomeric compounds, which were measured by high-performance liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS). Moreover, we showed that addition of purified VP in vitro improved the enzymatic hydrolysis of corn stover by 14.1%.

CONCLUSIONS

From the highly efficient system of enzymatic recalcitrance removal by new white-rot fungus, we identified a new delignification strategy based on VP which could oxidize both phenolic and nonphenolic lignin units and break different linkages in lignin. In addition, this is the first evidence that VP could break 5-5' linkage efficiently in vitro. Moreover, VP improved the enzymatic hydrolysis of corn stover in vitro. The remarkable lignin-degradative potential makes VP attractive for biotechnological applications.

Enhancement in multiple lignolytic enzymes production for optimized lignin degradation and selectivity in fungal pretreatment of sweet sorghum bagasse

The objective of this work was to study the increase in multiple lignolytic enzyme productions through the use of supplements in combination in pretreatment of sweet sorghum bagasse (SSB) by Coriolus versicolor such that enzymes act synergistically to maximize the lignin degradation and selectivity. Enzyme activities were enhanced by metallic salts and phenolic compound supplements in SSF. Supplement of syringic acid increased the activities of LiP, AAO and laccase; gallic acid increased MnP; CuSO₄ increased laccase and PPO to improve the lignin degradations and selectivity individually, higher than control. Combination of supplements optimized by RSM increased the production of laccase, LiP, MnP, PPO and AAO by 17.2, 45.5, 3.5, 2.4 and 3.6 folds respectively for synergistic action leading to highest lignin degradation (2.3 folds) and selectivity (7.1 folds). Enzymatic hydrolysis of pretreated SSB yielded ∼2.43 times fermentable sugar. This technique could be widely applied for pretreatment and enzyme productions.