Anode modification by biogenic gold nanoparticles for the improved performance of microbial fuel cells and microbial community shift

Investigation of microbial fuel cell performance based on the nickel thin film modified electrodes

Microbial fuel cells (MFCs) are a self-sustaining and environmentally friendly system for the simultaneous was tewater treatment and bioelectricity generation. The type and material of the electrode are critical factors that can influence the efficiency of this treatment process. In this study, graphite plates and carbon felt were modified through the electrodeposition of nickel followed by the formation of a biofilm, resulting in conductive bio-anode thin film electrodes with enhanced power generation capacity. The structural and morphological properties of the electrode surfaces were characterized using X-ray diffraction, energy-dispersive X-ray spectroscopy, elemental mapping, and field-emission scanning electron microscopy techniques. Maximum voltage, current density, and power generation were investigated using a dual-chamber MFC equipped with a Nafion 117 membrane and bio-nickel-doped carbon felt (bio-Ni@CF) and bio-nickel-doped graphite plate (bio-Ni@GP) electrodes under constant temperature conditions. The polarization and power curves obtained using different anode electrodes revealed that the maximum voltage, power and current density achieved with the bio-Ni@CF electrode were 468.0 mV, 130.72 mW/m2 and 760.0 mA/m2 respectively. Moreover, the modified electrodes demonstrated appropriate stability and resistance during successful runs. These results suggest that nickel-doped carbon-based electrodes can serve as suitable and stable supported catalysts and conductors for improving efficiency and increasing power generation in MFCs.

Impact of different zero valent iron-based particles on anaerobic microbial dechlorination of 2,4-dichlorophenol: Comparison of dechlorination performance and the underlying mechanism

The integration of iron-based materials and anaerobic microbial consortia has been extensively studied owing to its potential to enhance pollutant degradation. However, few studies have compared how different iron materials enhance the dechlorination of chlorophenols in coupled microbial systems. This study systematically compared the combined performances of microbial community (MC) and iron materials (Fe0/FeS2 +MC, S-nZVI+MC, n-ZVI+MC, and nFe/Ni+MC) for the dechlorination of 2,4-dichlorophenol (DCP) as one representative of chlorophenols. DCP dechlorination rate was significantly higher in Fe0/FeS2 +MC and S-nZVI+MC (1.92 and 1.67 times, with no significant difference between two groups) than in nZVI+MC and nFe/Ni+MC (1.29 and 1.25 times, with no significant difference between two groups). Fe0/FeS2 had better performance for the reductive dechlorination process as compared with other three iron-based materials via the consumption of any trace amount of oxygen in anoxic condition and accelerated electron transfer. On the other hand, nFe/Ni could induce different dechlorinating bacteria as compared to other iron materials. The enhanced microbial dechlorination was mainly due to some putative dechlorinating bacteria (Pseudomonas, Azotobacter, Propionibacterium), and due to improved electron transfer of sulfidated iron particles. Therefore, Fe0/FeS2 as a biocompatible as well as low-cost sulfidated material can be a good alternative for possible engineering applications in groundwater remediation.

Combining biological denitrification and electricity generation in methane-powered microbial fuel cells

Methane has been demonstrated to be a feasible substrate for electricity generation in microbial fuel cells (MFCs) and denitrifying anaerobic methane oxidation (DAMO). However, these two processes were evaluated separately in previous studies and it has remained unknown whether methane is able to simultaneously drive these processes. Here we investigated the co-occurrence and performance of these two processes in the anodic chamber of MFCs. The results showed that methane successfully fueled both electrogenesis and denitrification. Importantly, the maximum nitrate removal rate was significantly enhanced from (1.4 ± 0.8) to (18.4 ± 1.2) mg N/(L·day) by an electrogenic process. In the presence of DAMO, the MFCs achieved a maximum voltage of 610 mV and a maximum power density of 143 ± 12 mW/m². Electrochemical analyses demonstrated that some redox substances (e.g. riboflavin) were likely involved in electrogenesis and also in the denitrification process. High-throughput sequencing indicated that the methanogen Methanobacterium, a close relative of Methanobacterium espanolae, catalyzed methane oxidation and cooperated with both exoelectrogens and denitrifiers (e.g., Azoarcus). This work provides an effective strategy for improving DAMO in methane-powered MFCs, and suggests that methanogens and denitrifiers may jointly be able to provide an alternative to archaeal DAMO for methane-dependent denitrification.

Self-assembly of cell-embedding reduced graphene oxide/ polypyrrole hydrogel as efficient anode for high-performance microbial fuel cell

A three-dimensional (3D) macroporous reduced graphene oxide/polypyrrole (rGO/Ppy) hydrogel assembled by bacterial cells was fabricated and applied for microbial fuel cells. By taking the advantage of electroactive cell-induced bioreduction of graphene oxide and in-situ polymerization of Ppy, a facile self-assembly by Shewanella oneidensis MR-1and in-situ polymerization approach for 3D rGO/Ppy hydrogel preparation was developed. This facile one-step self-assembly process enabled the embedding of living electroactive cells inside the hydrogel electrode, which showed an interconnected 3D macroporous structures with high conductivity and biocompatibility. Electrochemical analysis indicated that the self-assembly of cell-embedding rGO/Ppy hydrogel enhanced the electrochemical activity of the bioelectrode and reduced the electron charge transfer resistance between the cells and the electrode. Impressively, extremely high power output of 3366 ± 42 mW m^-2 was achieved from the MFC with cell-embedding rGO/Ppy hydrogel rGO/Ppy, which was 8.6 times of that delivered from the MFC with bare electrode. Further analysis indicated that the increased cell loading by the hydrogel and improved electrochemical activity by the rGO/Ppy composite would be the underlying mechanism for this performance improvement. This study provided a facile approach to fabricate the biocompatible and electrochemical active 3D nanocomposites for MFC, which would also be promising for performance optimization of various bioelectrochemical systems.

Interactions between dissolved organic matter and the microbial community are modified by microplastics and heat waves

Dissolved organic matter (DOM) exists widely in natural waters and plays an important role in river carbon cycles and greenhouse gas emissions through microbial interactions. However, information on DOM-microbe associations in response to environmental stress is limited. River environments are the main carriers of microplastic (MP) pollution, and global heat waves (HWs) are threatening river ecology. Here, through MP exposure and HW simulation experiments, we found that DOM molecular weight and aromaticity were closely related to initial microbial communities. Moreover, MP-derived DOM regulated microbial community abundance and diversity, influenced microorganism succession trajectories as deterministic factors, and competed with riverine DOM for microbial utilization. SimulatedHWs enhanced the MP-derived DOM competitive advantage and drove the microbial community to adopt a K-strategy for effective recalcitrant carbon utilization. Relative to single environmental stressor exposure, combined MP pollution and HWs led to a more unstable microbial network. This study addresses how MPs and HWs drive DOM-microbe interactions in rivers, contributes to an in-depth understanding of the fate of river DOM and microbial community succession processes, and narrows the knowledge gap in understanding carbon sinks in aquatic ecosystems influenced by human activities and climate change.

Improved performance of Cr(vi)-reducing microbial fuel cells by nano-FeS hybridized biocathodes

Biocathode microbial fuel cells (MFCs) show promise for Cr(vi)-contaminated wastewater treatment. However, biocathode deactivation and passivation caused by highly toxic Cr(vi) and nonconductive Cr(iii) deposition limit the development of this technology. A nano-FeS hybridized electrode biofilm was fabricated by simultaneously feeding Fe and S sources into the MFC anode. This bioanode was then reversed as the biocathode to treat Cr(vi)-containing wastewater in a MFC. The MFC obtained the highest power density (40.75 ± 0.73 mW m^-2) and Cr(vi) removal rate (3.99 ± 0.08 mg L^-1 h^-1), which were 1.31 and 2.00 times those of the control, respectively. The MFC also maintained high stability for Cr(vi) removal in three consecutive cycles. These improvements were due to synergistic effects of nano-FeS with excellent properties and microorganisms in the biocathode. The mechanisms were: (1) the accelerated electron transfer mediated by nano-FeS 'electron bridges' strengthened bioelectrochemical reactions, firstly realizing deep reduction of Cr(vi) to Cr(0) and thus effectively alleviating cathode passivation; (2) nano-FeS as 'armor' layers improved cellular viability and extracellular polymeric substance secretion; (3) the biofilm selectively enriched a diversity of bifunctional bacteria for electrochemical activity and Cr(vi) removal. This study provides a new strategy to obtain electrode biofilms for sustainable treatment of heavy metal wastewater.

Microbial Biofuel Cells: Fundamental Principles, Development and Recent Obstacles

This review focuses on the development of microbial biofuel cells to demonstrate how similar principles apply to the development of bioelectronic devices. The low specificity of microorganism-based amperometric biosensors can be exploited in designing microbial biofuel cells, enabling them to consume a broader range of chemical fuels. Charge transfer efficiency is among the most challenging and critical issues while developing biofuel cells. Nanomaterials and particular redox mediators are exploited to facilitate charge transfer between biomaterials and biofuel cell electrodes. The application of conductive polymers (CPs) can improve the efficiency of biofuel cells while CPs are well-suitable for the immobilization of enzymes, and in some specific circumstances, CPs can facilitate charge transfer. Moreover, biocompatibility is an important issue during the development of implantable biofuel cells. Therefore, biocompatibility-related aspects of conducting polymers with microorganisms are discussed in this review. Ways to modify cell-wall/membrane and to improve charge transfer efficiency and suitability for biofuel cell design are outlined.

Functional Nanomaterial-Modified Anodes in Microbial Fuel Cells: Advances and Perspectives

Microbial fuel cell (MFC) is a promising approach that could utilize microorganisms to oxidize biodegradable pollutants in wastewater and generate electrical power simultaneously. Introducing advanced anode nanomaterials is generally considered as an effective way to enhance MFC performance by increasing bacterial adhesion and facilitating extracellular electron transfer (EET). This review focuses on the key advances of recent anode modification materials, as well as the current understanding of the microbial EET process occurring at the bacteria-electrode interface. Based on the difference in combination mode of the exoelectrogens and nanomaterials, anode surface modification, hybrid biofilm construction and single-bacterial surface modification strategies are elucidated exhaustively. The inherent mechanisms may help to break through the performance output bottleneck of MFCs by rational design of EET-related nanomaterials, and lead to the widespread application of microbial electrochemical systems.

Enhanced transmembrane electron transfer in Shewanella oneidensis MR-1 using gold nanoparticles for high-performance microbial fuel cells

Low efficiency of extracellular electron transfer (EET) is a major bottleneck in developing high-performance microbial fuel cells (MFCs). Herein, we construct Shewanella oneidensis MR-1@Au for the bioanode of MFCs. Through performance recovery experiments of mutants, we proved that abundant Au nanoparticles not only tightly covered the bacteria surface, but were also distributed in the periplasm and cytoplasm, and even embedded in the outer and inner membranes of the cell. These Au nanoparticles could act as electron conduits to enable highly efficient electron transfer between S. oneidensis MR-1 and electrodes. Strikingly, the maximum power density of the S. oneidensis MR-1@Au bioanode reached up to 3749 mW m^-2, which was 17.4 times higher than that with the native bacteria, reaching the highest performance yet reported in MFCs using Au or Au-based nanocomposites as the anode. This work elucidates the role of Au nanoparticles in promoting transmembrane and extracellular electron transfer from the perspective of molecular biology and electrochemistry, while alleviating bottlenecks in MFC performances.

Simultaneous boost of anodic electron transfer and exoelectrogens enrichment by decorating electrospinning carbon nanofibers in microbial fuel cell

Microbial fuel cell (MFC) is a promising technology in wastewater recovery driven by microbial metabolism. However, the low power output resulting from the sluggish extracellular electron transfer (EET) between the anode surface and exoelectrogens dramatically restricted the further application. This study fabricated a high-performance anode by decorating porous and conductive electrospinning carbon nanofibers (CNFs). The maximum power density in MFC modified with 14 wt% polyacrylonitrile CNFs (M-CNF14, 9.6 ± 0.2 W m^-3) was 1.9 and 2.7 times higher than carbon black modified MFC (M-CB, 5.1 ± 0.1 W m^-3) and the blank (M-BA, 3.6 ± 0.1 W m^-3), respectively. Denser biofilm and more microbial nanowires were observed in the M-CNF14 anode than in other conditions. Furthermore, the redox peak current of c-type cytochrome was 1.7-21 times higher in M-CNF14 than in the blank control, verifying the preferable EET activity. Several exoelectrogens like Petrimonas and Comamonas were enriched in M-CNF14 and showed a positive correlation to power generation. Besides, more simplified and modular interrelations among exoelectrogens and other bacteria were obtained in M-CNF14. This study revealed the microbial-related mechanism for simultaneously improving EET and exoelectrogens enrichment by CNFs modified anode, providing guidelines for high-performance wastewater recovery.

Applications of Nanomaterials in Microbial Fuel Cells: A Review

Microbial fuel cells (MFCs) are an environmentally friendly technology and a source of renewable energy. It is used to generate electrical energy from organic waste using bacteria, which is an effective technology in wastewater treatment. The anode and the cathode electrodes and proton exchange membranes (PEM) are important components affecting the performance and operation of MFC. Conventional materials used in the manufacture of electrodes and membranes are insufficient to improve the efficiency of MFC. The use of nanomaterials in the manufacture of the anode had a prominent effect in improving the performance in terms of increasing the surface area, increasing the transfer of electrons from the anode to the cathode, biocompatibility, and biofilm formation and improving the oxidation reactions of organic waste using bacteria. The use of nanomaterials in the manufacture of the cathode also showed the improvement of cathode reactions or oxygen reduction reactions (ORR). The PEM has a prominent role in separating the anode and the cathode in the MFC, transferring protons from the anode chamber to the cathode chamber while preventing the transfer of oxygen. Nanomaterials have been used in the manufacture of membrane components, which led to improving the chemical and physical properties of the membranes and increasing the transfer rates of protons, thus improving the performance and efficiency of MFC in generating electrical energy and improving wastewater treatment.

Modification of carbon foam with 4-mercaptobenzoic acid functionalised gold nanoparticles for an application in a yeast-based microbial fuel cell

Modification of carbon foam with gold nanoparticles (AuNPs) was successfully performed through a hydrothermal method. The modified AuNPs were functionalised with 4-mercaptobenzoic acid (MBA) to improve their affinity toward microorganisms. TEM and SEM characterization indicated that although polydisperse spherical nanoparticles of AuNPs with particle sizes around 17 nm were obtained, the attached nanoparticles were agglomerated to be around 0.4 to 1.5 μm in size on the carbon foam surface. The electrochemical studies using cyclic voltammetry technique affirmed that the modified carbon foam electrodes have electroactive properties against glucose. Evaluation of the electrode was performed for a microbial fuel cell using Candida fukuyamaensis yeast as the microorganisms. The polarization curves showed that functionalisation of AuNPs-modified carbon foam with MBA provides around three times higher current density (1226.93 mA m^-2) and power density (330.61 mW m^-2) compared to the unmodified one. This result indicated that the modification is suitable to improve yeast attachment on the electrode surface.

Advancements on sustainable microbial fuel cells and their future prospects: A review

A microbial fuel cell (MFC) is a sustainable device that produces electricity. The main components of MFC are electrodes (anode & cathode) and separators. The MFC's performance is ascertained by measuring its power density. Its components and other parameters, such as cell design and configuration, operation parameters (pH, salinity, and temperature), substrate characteristics, and microbes present in the substrate, all influence its performance. MFC can be scaled up and commercialized using low-cost materials without affecting its performance. Hence the choice of materials plays a significant role. In the past, precious and non-precious metals were mostly used. These were replaced by a variety of low-cost carbonaceous and non-carbonaceous materials. Nano materials, activated compounds, composite materials, have also found their way as components of MFC materials. This review describes the recently reported modified electrodes (anode and cathode), their improvisation, their merits, pollutant removal efficiency, and associated power density.

Enhancement of wastewater treatment under low temperature using novel electrochemical active biofilms constructed wetland

A novel electrochemical active biofilms constructed wetland (NEAB-CW) was built to enhance the treatment efficiency for domestic sewage under low temperature environment (0-15 °C). In NEAB-CW, the traditional matrixes were replaced with conductive layer, in which laid stainless steel mesh tubes (SSMT) and added slow-release oxygen matrixes (SROM) and zero-valent iron rod (IR) were used to build a bioelectrochemical activity biofilms system. According to the results of 180 d experiment, the removal efficiencies of COD, NH₄⁺-N and TP of NEAB-CW were 1.52 and 2.21, 2.97 and 1.68, 3.95 and 1.76 times higher than the CW without SROM and IR at 10-20 and 0-10 °C, respectively. The transverse and longitudinal electric potential (EP) variations in NEAB-CW improved microbial activities under low temperature by enhancing the electron transfer efficiency, resulting in higher and stable EP and electron currents density, as well as protein-like contents secreted from biofilms. The pollutant-degrading microorganisms (e.g., Clostridia, Simplicispira), low temperature-resistant microorganisms (e.g., Psychrobacter, Acinetobacter), and electrochemical active microorganisms (e.g., Negativicutes, Gammaproteobacteria) obviously accumulated in NEAB-CW under low temperature environment to generate electricity and degrade pollutants. The results provided a good choice to treat domestic sewage at 0-15 °C by using NEAB-CW.

Advancements in Bioelectricity Generation Through Nanomaterial-Modified Anode Electrodes in Microbial Fuel Cells

The use of nanotechnology in bioelectrochemical systems to recover bioelectricity and metals from waste appears to be a potentially appealing alternative to existing established procedures. This trend exactly characterizes the current renewable energy production technology. Hence, this review focuses on the improvement of the anode electrode by using different functional metal oxide-conducting polymer nanocomposites to enhance microbial fuel cell (MFC) performance. Enhancement of interfacial bioelectrocatalysis between electroactive microorganisms and hierarchical porous nanocomposite materials could enhance cost-effective bioanode materials with superior bioelectrocatalytic activity for MFCs. In this review, improvement in efficiency of MFCs by using iron oxide- and manganese oxide-based polypyrrole hybrid composites as model anode modifiers was discussed. The review also extended to discussing and covering the principles, components, power density, current density, and removal efficiencies of biofuel cell systems. In addition, this research review demonstrates the application of MFCs for renewable energy generation, wastewater treatment, and metal recovery. This is due to having their own unique working principle under mild conditions and using renewable biodegradable organic matter as a direct fuel source.

N-acyl-homoserine lactones in extracellular polymeric substances from sludge for enhanced chloramphenicol-degrading anode biofilm formation in microbial fuel cells

Exploring an efficient acclimation strategy to obtain robust bioanodes is of practical significance for antibiotic wastewater treatment by bioelectrochemical systems (BESs). This study investigated the effects of two acclimation conditions on chloramphenicol (CAP)-degrading anode biofilm formation in microbial fuel cells (MFCs). The one was continuously added the extracellular polymeric substances (EPS) extracted from anaerobic sludge and increasing concentrations of CAP after the first start-up phase, while the other was added the EPS-1 (N-acyl-homoserine lactones, namely AHLs were extracted from the EPS) at the same conditions. The results demonstrated that AHLs in the sludge EPS played a crucial role for enhanced CAP-degrading anode biofilm formation in MFCs. The AHL-regulation could not only maintain stable voltage outputs but also significantly accelerate CAP removal in the EPS MFC. The maximum voltage of 653.83 mV and CAP removal rate of 1.21 ± 0.05 mg/L·h were attained from the EPS MFC at 30 mg/L of CAP, which were 0.84 and 1.57 times higher than those from the EPS-1 MFC, respectively. These improvements were largely caused by the thick and 3D structured biofilm, strong and homogeneous cell viability throughout the biofilm, and high protein/polysaccharide ratio along with more conductive contents in the biofilm EPS. Additionally, AHLs facilitated the formation of a biofilm with rich biodiversity and balanced bacterial proportions, leading to more beneficial mutualism among different functional bacteria. More bi-functional bacteria (for electricity generation and antibiotic resistance/degradation) were specifically enriched by AHLs as well. These findings provide quorum sensing theoretical knowledge and practical instruction for rapid antibiotic-degrading electrode biofilm acclimation in BESs.

Defined and unknown roles of conductive nanoparticles for the enhancement of microbial current generation: A review

The ability of various bacteria to make use of solid substrates through extracellular electron transfer (EET) or extracellular electron uptake (EEU) has enabled the development of valuable biotechnologies such as microbial fuel cells (MFCs) and microbial electrosynthesis (MES). It is common practice to use metallic and semiconductive nanoparticles (NPs) for microbial current enhancement. However, the effect of NPs is highly variable between systems, and there is no clear guideline for effectively increasing the current generation. In the present review, the proposed mechanisms for enhancing current production in MFCs and MES are summarized, and the critical factors for NPs to enhance microbial current generation are discussed. Implications for microbially induced iron corrosion, where iron sulfide NPs are proposed to enhance the rate of EEU, photochemically driven MES, and several future research directions to further enhance microbial current generation, are also discussed.

In situ fabrication of gold nanoparticles into biocathodes enhance chloramphenicol removal

The development of highly conductive biofilms is a key strategy to enhance antibiotic removal in bioelectrochemical systems (BESs) with biocathodes. In this study, Au nanoparticles (Au-NPs) were in situ fabricated in a biocathode (^Au biocathode) to enhance the removal of chloramphenicol (CAP) in BESs. The concentration of Au(III) was determined to be 5 mg/L. CAP was effectively removed in the BES containing a ^Au biocathode with a removal percentage of 94.0% within 48 h; this result was 1.8-fold greater than that obtained using a biocathode without Au-NPs (51.7%). The Au-NPs significantly reduced the charge transfer resistance and promoted the electrochemical activity of the biocathode. In addition, the ^Au biocathode showed a specifical enrichment of Dokdonella, Bosea, Achromobacter, Bacteroides and Petrimonas, all of which are associated with electron transfer and contaminant degradation. This study provides a new strategy for enhancing CAP removal in BESs through a simple and eco-friendly electrode design.

A review of recent advances in electrode materials for emerging bioelectrochemical systems: From biofilm-bearing anodes to specialized cathodes

Bioelectrochemical systems (BES), mainly microbial fuel cells (MEC) and microbial electrolysis cells (MFC), are unique biosystems that use electroactive bacteria (EAB) to produce electrons in the form of electric energy for different applications. BES have attracted increasing attention as a sustainable, low-cost, and neutral-carbon option for energy production, wastewater treatment, and biosynthesis. Complex interactions between EAB and the electrode materials play a crucial role in system performance and scalability. The electron transfer processes from the EAB to the anode surface or from the cathode surface to the EAB have been the object of numerous investigations in BES, and the development of new materials to maximize energy production and overall performance has been a hot topic in the last years. The present review paper discusses the advances on innovative electrode materials for emerging BES, which include MEC coupled to anaerobic digestion (MEC-AD), Microbial Desalination Cells (MDC), plant-MFC (P-MFC), constructed wetlands-MFC (CW-MFC), and microbial electro-Fenton (BEF). Detailed insights on innovative electrode modification strategies to improve the electrode transfer kinetics on each emerging BES are provided. The effect of materials on microbial population is also discussed in this review. Furthermore, the challenges and opportunities for materials scientists and engineers working in BES are presented at the end of this work aiming at scaling up and industrialization of such versatile systems.

Improving the anode performance of microbial fuel cell with carbon nanotubes supported cobalt phosphate catalyst

Microbial fuel cell (MFC) is a sustainable technology that can convert waste to energy by harnessing the power of exoelectrogenic bacteria. However, the poor biocompatibility and low electrocatalytic activities of surface usually cause weak bacterial adhesion and low electron transfer efficiency, which seriously hampers the development of MFCs. Herein, a novel carbon nanotube supported cobalt phosphate (CNT/Co-Pi) electrode is fabricated by assembling CNTs on carbon cloth, followed by the electrodeposition of Co-Pi catalyst. The deposited amorphous Co-Pi thin film contains phosphate and the cobalt ions of multiple oxidation states. The hydrophilic phosphate can promote the adhesion of microorganisms on electrode. The strong conversion ability of multiple states of cobalt offers excellent electrocatalytic activity for the electron transfer across biotic/abiotic interface. Therefore, the highly conductive CNTs substrate, along with the Co-Pi catalyst, provide an effective electron transfer between the electrogenic bacteria and the electrode, which endows MFC high power densities up to 1200 mW m^-2. Our work has demonstrated for the first time that CNT/Co-Pi catalyst can promote the interfacial electron transfer between electrogenic bacteria and electrode, and highlighted the application potentials of Co-Pi as an anode catalyst for the fabrication of high performance MFC anodes.

The impacts of metal-based engineered nanomaterial mixtures on microbial systems: A review

The last decade has witnessed tremendous growth in the commercial use of metal-based engineered nanomaterials (ENMs) for a wide range of products and processes. Consequently, direct and indirect release into environmental systems may no longer be considered negligible or insignificant. Yet, there is an active debate as to whether there are real risks to human or ecological health with environmental exposure to ENMs. Previous research has focused primarily on the acute effects of individual ENMs using pure cultures under controlled laboratory environments, which may not accurately reveal the ecological impacts of ENMs under real environmental conditions. The goal of this review is to assess our current understanding of ENM effects as we move from exposure of single to multiple ENMs or microbial species. For instance, are ENMs' impacts on microbial communities predicted by their intrinsic physical or chemical characteristics or their effects on single microbial populations; how do chronic ENM interactions compare to acute toxicity; does behavior under simplified laboratory conditions reflect that in environmental media; finally, is biological stress modified by interactions in ENM mixtures relative to that of individual ENM? This review summarizes key findings and our evolving understanding of the ecological effects of ENMs under complex environmental conditions on microbial systems, identifies the gaps in our current knowledge, and indicates the direction of future research.

Carbon-Based Composites as Anodes for Microbial Fuel Cells: Recent Advances and Challenges

Owing to the low price, chemical stability and good conductivity, carbon-based materials have been extensively applied as the anode in microbial fuel cells (MFCs). In this review, apart from the charge storage mechanism and anode requirements, the major work focuses on five categories of carbon-based anode materials (traditional carbon, porous carbon, nano-carbon, metal/carbon composite and polymer/carbon composite). The relationship is demonstrated in depth between the physicochemical properties of the anode surface/interface/bulk (porosity, surface area, hydrophilicity, partical size, charge, roughness, etc.) and the bioelectrochemical performances (electron transfer, electrolyte diffusion, capacitance, toxicity, start-up time, current, power density, voltage, etc.). An outlook for future work is also proposed.

Sustainable Syntheses and Sources of Nanomaterials for Microbial Fuel/Electrolysis Cell Applications: An Overview of Recent Progress

The use of microbial fuel cells (MFCs) is quickly spreading in the fields of bioenergy generation and wastewater treatment, as well as in the biosynthesis of valuable compounds for microbial electrolysis cells (MECs). MFCs and MECs have not been able to penetrate the market as economic feasibility is lost when their performances are boosted by nanomaterials. The nanoparticles used to realize or decorate the components (electrodes or the membrane) have expensive processing, purification, and raw resource costs. In recent decades, many studies have approached the problem of finding green synthesis routes and cheap sources for the most common nanoparticles employed in MFCs and MECs. These nanoparticles are essentially made of carbon, noble metals, and non-noble metals, together with a few other few doping elements. In this review, the most recent findings regarding the sustainable preparation of nanoparticles, in terms of syntheses and sources, are collected, commented, and proposed for applications in MFC and MEC devices. The use of naturally occurring, recycled, and alternative raw materials for nanoparticle synthesis is showcased in detail here. Several examples of how these naturally derived or sustainable nanoparticles have been employed in microbial devices are also examined. The results demonstrate that this approach is valuable and could represent a solid alternative to the expensive use of commercial nanoparticles.

Boosting the anode performance of microbial fuel cells with a bacteria-derived biological iron oxide/carbon nanocomposite catalyst

Modifying the electrodes of microbial fuel cells (MFCs) with iron oxides can improve the bacterial attachment performances and electrocatalytic activities for energy conversion, which is of significance in the fabrication of MFCs. However, the conventional modification methods usually result in the aggregation of iron sites, producing the electrodes of poor qualities. Herein, we report a novel method for the modification of electrochemical electrodes to boost the anode performance of MFC. The Shewanella precursor adhered on carbon felt electrode was directly carbonized to form a bacteria-derived biological iron oxide/carbon (Bio-FeOx/C) nanocomposite catalyst. The large spatial separation between the bacteria, as well as those between the iron containing proteins in the bacteria, deliver a highly dispersed Bio-FeOx/C nanocomposite with good electrocatalytic activities. The excellent microbial attachment performance and electron transfer rate of the Bio-FeOx/C modified electrode significantly promote the transfer of produced electrons between bacteria and electrode. Accordingly, the MFC with the Bio-FeOx/C electrode exhibits the maximum power density of 797.0 mW m^-2, much higher than that obtained with the conventional carbon felt anode (226.1 mW m^-2). Our works have paved a new avenue to the conversion of the natural bacterial precursors into active iron oxide nanoparticles as the anode catalyst of MFCs. The high catalytic activity of the prepared Bio-FeOx endows it great application potentials in the construction of high-performance electrodes.

From Microorganism-Based Amperometric Biosensors towards Microbial Fuel Cells

This review focuses on the overview of microbial amperometric biosensors and microbial biofuel cells (MFC) and shows how very similar principles are applied for the design of both types of these bioelectronics-based devices. Most microorganism-based amperometric biosensors show poor specificity, but this drawback can be exploited in the design of microbial biofuel cells because this enables them to consume wider range of chemical fuels. The efficiency of the charge transfer is among the most challenging and critical issues during the development of any kind of biofuel cell. In most cases, particular redox mediators and nanomaterials are applied for the facilitation of charge transfer from applied biomaterials towards biofuel cell electrodes. Some improvements in charge transfer efficiency can be achieved by the application of conducting polymers (CPs), which can be used for the immobilization of enzymes and in some particular cases even for the facilitation of charge transfer. In this review, charge transfer pathways and mechanisms, which are suitable for the design of biosensors and in biofuel cells, are discussed. Modification methods of the cell-wall/membrane by conducting polymers in order to enhance charge transfer efficiency of microorganisms, which can be potentially applied in the design of microbial biofuel cells, are outlined. The biocompatibility-related aspects of conducting polymers with microorganisms are summarized.

Bridging the gap to hydrochar production and its application into frameworks of bioenergy, environmental and biocatalysis areas

Hydrothermal carbonization (HTC) is a facile, low-cost and eco-friendly thermal conversion process that has recently gained attention with a growing number of publications (lower 50 in 2000 to over 1500 in 2020). Despite being a promising technology, problems such as operational barriers, complex reaction mechanisms and scaling have to be solved to make it a commercial technology. To bridge this current gap, this review elaborates on the chemistry of the conversion of lignocellulosic biomass. Besides, a comprehensive overview of the influence of the HTC operational conditions (pH, temperature, water:biomass ratio, residence time and water recirculation) are discussed to better understand how hydrochar with desired properties can be efficiently produced. Large-scale examples of the application of HTC are also presented. Current applications of hydrochar in the fields of energy, biocatalysis and environment are reviewed. Finally, economic cost and future prospects are analyzed.

Biosynthesized iron sulfide nanoparticles by mixed consortia for enhanced extracellular electron transfer in a microbial fuel cell

The bioanode of mixed consortia was for the first time used to in-situ synthesize iron sulfide nanoparticles in a microbial fuel cell (MFC) over a long-term period (46 days). These poorly crystalline nanoparticles with an average size of 29.97 ± 7.1 nm, comprising of FeS and FeS₂, significantly promoted extracellular electron transfer and thus the electricity generation of the MFC. A maximum power density of 519.00 mW/m² was obtained from the MFC, which was 1.92 times as high as that of the control. The cell viability was promoted by a small amount of iron sulfide nanoparticles but inhibited by the thick nanoparticle "shell" covered on the bacterial cells. Some electroactive and sulfur reducing bacteria (eg. Enterobacteriaceae, Desulfovibrio, and Geobacter) were specifically enriched on the anode. This study provides a novel insight for improving the performance of bioelectrochemical systems through in-situ sustainable nanomaterials biofabrication by mixed consortia.

Application of advanced anodes in microbial fuel cells for power generation: A review

Microbial fuel cells (MFCs) the most extensively described bioelectrochemical systems (BES), have been made remarkable progress in the past few decades. Although the energy and environment benefits of MFCs have been recognized in bioconversion process, there are still several challenges for practical applications on large-scale, particularly for relatively low power output by high ohmic resistance and long period of start-up time. Anodes serving as an attachment carrier of microorganisms plays a vital role on bioelectricity production and extracellular electron transfer (EET) between the electroactive bacteria (EAB) and solid electrode surface in MFCs. Therefore, there has been a surge of interest in developing advanced anodes to enhance electrode electrical properties of MFCs. In this review, different properties of advanced materials for decorating anode have been comprehensively elucidated regarding to the principle of well-designed electrode, power output and electrochemical properties. In particular, the mechanism of these materials to enhance bioelectricity generation and the synergistic action between the EAB and solid electrode were clarified in detail. Furthermore, development of next generation anode materials and the potential modification methods were also prospected.

Recent Advances in Anodes for Microbial Fuel Cells: An Overview

The recycling and treatment of wastewater using microbial fuel cells (MFCs) has been attracting significant attention as a way to control energy crises and water pollution simultaneously. Despite all efforts, MFCs are unable to produce high energy or efficiently treat pollutants due to several issues, one being the anode's material. The anode is one of the most important parts of an MFC. Recently, different types of anode materials have been developed to improve the removal rate of pollutants and the efficiency of energy production. In MFCs, carbon-based materials have been employed as the most commonly preferred anode material. An extensive range of potentials are presently available for use in the fabrication of anode materials and can considerably minimize the current challenges, such as the need for high quality materials and their costs. The fabrication of an anode using biomass waste is an ideal approach to address the present issues and increase the working efficiency of MFCs. Furthermore, the current challenges and future perspectives of anode materials are briefly discussed.

Effects of copper salts on performance, antibiotic resistance genes, and microbial community during thermophilic anaerobic digestion of swine manure

This study investigated methane production and ARGs reduction during thermophilic AD of swine manure with the addition of different Cu salts (cupric sulfate, cupric glycinate, and the 1:1 mixture of these two salts). Results showed methane production was increased by 28.78% through adding mixed Cu salts. The mixed Cu group effectively reduced total ARGs abundance by 26.94%, suggesting mixed Cu salts did not promote the potential ARGs risk. The positive effects of mixed Cu salts on AD performance and ARGs removal might be ascribed to the low bioavailability. Microbial community analysis indicated the highest abundances of Clostridia_MBA03 and Methanobacterium in the mixed Cu group might cause the increased methane production. Spearman's rank correlation analysis elucidated the succession in microbial community induced by environmental factors was the main driver for shaping ARGs profiles. Thus, mixed Cu salts could be an alternative to replace the inorganic Cu salt in animal feed additives.

Positive effects of concomitant heavy metals and their reduzates on hexavalent chromium removal in microbial fuel cells

The cooperative cathode modification by BioAu from Au(iii) and in situ Cu(ii) co-reduction enhanced Cr(vi) removal and bioelectricity generation in MFCs.

Three-dimensional high performance free-standing anode by one-step carbonization of pinecone in microbial fuel cells

In this paper, the free-standing macroporous carbon anode is prepared by one-step carbonization of pinecone without any further modification. The obtained anode is N, P-codoped porous carbon material, which is beneficial for electrochemical active bacterial adhesion and the fast start-up of cells. Both of the output voltage and long-term operation stability of the obtained anode are higher than that of carbon felt. The charge transfer resistance after biofilm formation is only 1.4 Ω, being 85.1% lower than that of carbon felt anode. 16S rRNA gene sequence analysis shows that Geobacter soli is the main electricigen and its ratio at the obtained anode is much higher than that at carbon felt (77.4% vs 34.0%). The N, P-codoped carbon as the three-dimensional free-standing anode has excellent electrochemical properties and is low cost and easy preparation. Most importantly, it enhances extracellular electron transfer, thus has potential application in microbial fuel cells.

Mechanism study of photo-induced gold nanoparticles formation by Shewanella oneidensis MR-1

Shewanella oneidensis MR-1, a bioelectricity generating bacterium, is broadly used in bioremediation, microbial fuel cell and dissimilatory reduction and recovery of precious metals. Herein, we report for the first time that photo induction as a trigger to stimulate gold nanoparticles (Au@NPs) formation by MR-1, with wavelength and light intensity as two key variables. Results indicated that sigmoidal model is the best fit for Au@NPs formation at various wavelengths (with R² > 0.97). Light intensity in terms of photosynthetic photon flux density (PPFD) critically influences the rate constant in the low-light intensity region (PPFD < 20), while wavelength controls the maximum rate constant in the high-light region (PPFD > 20). By deletion of Mtr pathway genes in MR-1, we proposed the mechanism for light induced Au@NP formation is the excitation effect of light on certain active groups and extracellular polymeric substances (EPS) on the cell surface. Also, the release of electrons from proteins and co-enzyme complexes enhance electron generation. To the best of our knowledge, this is the first-attempt to explore the effect of photo-induction on Au@NPs production by MR-1, which provides an alternative cost-effective and eco-friendly process in green chemical industry.