A modified method for enhancing adsorption capability of banana pseudostem biochar towards methylene blue at low temperature

Impact of Pyrolysis Temperature on the Physical and Chemical Properties of Non-Modified Biochar Produced from Banana Leaves: A Case Study on Ammonium Ion Adsorption

Given the current importance of using biochar for water treatment, it is important to study the physical-chemical properties to predict the behavior of the biochar adsorbent in contact with adsorbates. In the present research, the physical and chemical characteristics of three types of biochar derived from banana leaves were investigated, which is a poorly studied raw material and is considered an agricultural waste in some Latin American, Asian, and African countries. The characterization of non-modified biochar samples pyrolyzed at 300, 400, and 500 °C was carried out through pH, scanning electron microscopy, energy dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, and specific surface area measurements. The adsorption properties of banana leaf-derived biochar were evaluated by ammonium ion adsorption experiments. The results demonstrated that the pyrolysis temperature has a large impact on the yield, structure, elemental composition, and surface chemistry of the biochar. Biochar prepared at 300 °C is the most efficient for NH4+ adsorption, achieving a capacity of 7.0 mg of adsorbed NH4+ on each gram of biochar used, while biochar samples prepared at 400 and 500 °C show lower values of 6.1 and 5.6 mg/g, respectively. The Harkins-Jura isotherm model fits the experimental data best for all biochar samples, demonstrating that multilayer adsorption occurs on our biochar.

A green and economic approach to synthesize magnetic Lagenaria siceraria biochar (γ-Fe2O3-LSB) for methylene blue removal from aqueous solution

In the printing and textile industries, methylene blue (a cationic azo dye) is commonly used. MB is a well-known carcinogen, and another major issue is its high content in industrial discharge. There are numerous removal methodologies that have been employed to remove it from industrial discharge; however, these current modalities have one or more limitations. In this research, a novel magnetized biochar (γ-Fe2O3-LSB) was synthesized using Lagenaria siceraria peels which were further magnetized via the co-precipitation method. The synthesized γ-Fe2O3-LSB was characterized using FTIR, X-ray diffraction, Raman, SEM-EDX, BET, and vibrating sample magnetometry (VSM) for the analysis of magnetic properties. γ-Fe2O3-LSB showed a reversible type IV isotherm, which is a primary characteristic of mesoporous materials. γ-Fe2O3-LSB had a specific surface area (SBET = 135.30 m2/g) which is greater than that of LSB (SBET = 11.54 m2/g). γ-Fe2O3-LSB exhibits a saturation magnetization value (Ms) of 3.72 emu/g which shows its superparamagnetic nature. The batch adsorption process was performed to analyze the adsorptive removal of MB dye using γ-Fe2O3-LSB. The adsorption efficiency of γ-Fe2O3-LSB for MB was analyzed by varying parameters like the initial concentration of adsorbate (MB), γ-Fe2O3-LSB dose, pH effect, contact time, and temperature. Adsorption isotherm, kinetic, and thermodynamics were also studied after optimizing the protocol. The non-linear Langmuir model fitted the best to explain the adsorption isotherm mechanism and resulting adsorption capacity ( q e =54.55 mg/g). The thermodynamics study showed the spontaneous and endothermic nature, and pseudo-second-order rate kinetics was followed during the adsorption process. Regeneration study showed that γ-Fe2O3-LSB can be used up to four cycles. In laboratory setup, the cost of γ-Fe2O3-LSB synthesis comes out to be 162.75 INR/kg which is low as compared to commercially available adsorbents. The results obtained suggest that magnetic Lagenaria siceraria biochar, which is economical and efficient, can be used as a potential biochar material for industrial applications in the treatment of wastewater.

Valorization of Waste Watermelon Rinds as a Bio-adsorbent for Efficient Removal of Methylene Blue Dye from Aqueous Solutions

Nature-based solutions (NBSs) for remediation of various emerging contaminants have gained impetus during the last few decades. In the current study, watermelon (citrullus lanatus), a highly consumed seasonal fruit, was used as a feedstock waste biomass for biochar synthesis through valorization of watermelon rinds. The watermelon biochar (WM-BC) was synthesized through slow pyrolysis at 550°C under anoxic conditions. Langmuir model with R2>99, was found to best fit the adsorption isotherm, and the adsorption kinetics was best described by the pseudo-second-order model. Various characterization tools including FTIR, SEM, BET, XRD, and TEM were used to evaluate the surface morphology of the biochar. The removal efficiency increased from 35% (dosage = 0.4 g), to 81% at WM-BC dosage of 2 g. A maximum adsorption capacity of 115.61 mg/g was found. The results from kinetic and isotherm model model suggested that the adsorption was favorable and multilayer adsorption can be considered. The adsorption mechanism was found to be governed by the co-existing factors such as hydrogen bonding, electrostatic interactions, and aromatic interactions. Results suggest that WM-BC has high potential to be employed as an adsorbent for efficient remediation of methylene blue dyes from aqueous solutions.

Sulfuric acid-assisted ball milling for the preparation of Si-O-enriched straw biochar: removal efficiency of rhodamine B and adsorption mechanism

Traditional pyrolysis biochar has been widely employed to treat dye wastewater. However, there are some problems in the pyrolysis process, such as the generation of harmful gases and the low content of silico-oxygen functional groups to promote adsorption. Straw biochar (Ac-BCbm) was prepared by sulfuric acid co-ball milling method. The adsorption performance and adsorption mechanism of rhodamine B (RhB) under different preparation conditions and factors were investigated. The results showed that the adsorption rate of Ac-BCbm on RhB was up to 94.9%, which was 60.5% and 55.8% higher than that of ball-milling straw (STbm) and biochar prepared by pyrolysis (STBC600), respectively. The Ac-BCbm had better adaptability under different pH and common interfering ions for remove RhB. Characterization and DFT simulation analysis revealed that the sulfuric acid co-ball milling process promoted the formation of Si-OH and Si-O-CH3 oxygen-containing functional groups of Si component in straw, which enhanced the hydrogen bonding interactions and effectively improved the adsorption efficiency. This study investigated a new strategy for biochar preparation by sulfuric acid co-ball milling, which provides an additional development direction for the efficient resource utilization of straw.

Effects of cation types in persulfate on physicochemical and adsorptive properties of biochar prepared from persulfate-pretreated bamboo

The adsorption behaviors of biochar are largely impacted by biomassfeedstock. In this study, two biochars were prepared from torrefaction of ammonium persulfate- and potassium persulfate-pretreated bamboo and then activated by cold alkali, which are named as ASBC and KSBC, respectively. The two biochars were characterized by different instruments, and their adsorption properties over cationic methylene blue (MB) were compared. The type of persulfates little affected the specific surface areas, but significantly impacted O (29.54 % vs. 35.113 %) and N (12.13 % vs. 3.74 %) contents, functional groups, and zeta potentials of biochars. MB adsorption onto ASBC/KSBC is a single-layer chemical endothermic process and ASBC/KSBC exhibit high adsorption capacity over MB (475/881 mg·g-1) at 303 K. Obviously, the sorption capacity of MB onto KSBC much surpasses that of MB onto ASBC. These results indicate biomass pre-treatment is a cheap and convenient method to prepare biochars with unique physicochemical and adsorptive properties.

Enhanced Adsorptive Removal of Tetracycline by Phosphomolybdic Acid-Modified Low-Temperature Sludge Biochar

Increasing the adsorption capacity and reducing the energy consumption of sludge biochar during preparation is important. In this study, a new modification method was developed to prepare phosphomolybdic acid-modified sludge biochar through the low-temperature pyrolysis of sewage sludge using phosphomolybdic acid as a modifier. Tetracycline was used to assess the adsorption performance of sludge biochar, and phosphomolybdic acid-modified sludge biochar was prepared at different temperatures. The results showed that the adsorption capacity of sludge biochar improved from 84.49 to 120.86 mg/g through modification with phosphomolybdic acid at 200 °C. The maximum adsorption capacities of phosphomolybdic acid-modified sludge biochar (200 °C pyrolysis temperature) at 298, 308, and 318 K were 283.87, 421.39, and 545.48 mg/g, respectively. Both liquid film and intraparticle diffusion were the main rate-limiting steps of tetracycline adsorption by phosphomolybdic acid-modified sludge biochar. Furthermore, the adsorption of tetracycline by phosphomolybdic acid-modified sludge biochar was mainly attributed to π-π interactions, electrostatic interactions, hydrogen bonding, and pore filling.

Agricultural waste biochar after potassium hydroxide activation: Its adsorbent evaluation and potential mechanism

The agricultural waste (Goji branch) was pyrolyzed into biochars with one-step potassium hydroxide (KOH) activation under different processing conditions. The biochars were first characterized in structural features and functional groups and then evaluated for adsorptive performance with methylene blue as a model pollutant. Different adsorption models were applied to fit the adsorption process and reveal the possible mechanisms. The adsorption capacity was found to strongly correlate (R2 = 0.9642) with the surface area of the biochars, among which biochar K50%W29%C-700 (pyrolysis at 700 °C in the presence of 50 % KOH and 29 % water) possessed the largest surface area (1378 m2/g) and exhibited the highest adsorption capacity (769 mg/g) compared to its homologous products. Biochar K50%W29%C-700 also showed excellent recyclability and potent adsorption capacity toward other common organic pollutants. The results suggest that traces of water in agricultural wastes could significantly intensify the KOH-involved activation efficiency of producing porous biochar.

Conversion of solid wastes and natural biomass for deciphering the valorization of biochar in pollution abatement: A review on the thermo-chemical processes

This overview addresses the formation of solid trash and the various forms of waste from a variety of industries, which environmentalists have embraced. The paper investigates the negative effects on the environment caused by unsustainable management of municipal solid trash as well as the opportunities presented by the formal system. This examination looks at the origins of solid waste as well as the typical treatment methods. Pyrolysis methods, feedstock pyrolysis, and lignocellulosic biomass pyrolysis were highlighted. Explain in detail the various thermochemical processes that take place during the pyrolysis of biomass. Due to its carbon content, low cost, accessibility, ubiquitousness, renewable nature, and environmental friendliness, biomass waste is a unique biochar precursor. This study looks at the different types of biomass waste that are available for treating wastewater. This study discussed a wide variety of reactors. Adsorption is the standard method that is used the most frequently to remove hazardous organic, dye, and inorganic pollutants from wastewater. These pollutants cause damage to the environment and water supplies, thus it is important to remove them. Adsorption is both simple and inexpensive to utilize. Temperature-dependent conversions explain the kinetic theories of biomaterial biochemical degradation. This article presents a review that explains how pyrolytic breakdown char materials can be used to reduce pollution and improve environmental management.

Lignin-modified metal-organic framework as an effective adsorbent for the removal of methyl orange

Herein, lignin-modified metal-organic frameworks (NH2-UIO@L) are prepared using a one-step synthesis as sorbents for the removal of organic dyes from water. The introduction of lignin improved the adsorption sites. NH2-UIO@L2 adsorption of MO conforms to Langmuir model, and the adsorption capacity of NH2-UIO@L2 on MO was 214.13 mg·L-1 with an adsorption efficiency up to 99.28 %, which was significantly higher than values for other adsorbents. Due to hydrogen bonds, π-π interactions and electrostatic interactions, MO was effectively removed by NH2-UIO@L2 and its adsorption efficiency is maintained at 90.55 % after six cycles. The adsorption kinetics showed that the NH2-UIO@L2 adsorption of MO was chemical adsorption and controlled by intraparticle diffusion and external mass transfer. Further, the adsorption performance of NH2-UIO@L2 on MO and MB in mixed MO/MB solution was investigated. The adsorption capacity of NH2-UIO@L2 in mixed MO/MB solution was 207.04 mg·L-1 for MO and 243.31 mg·L-1 for MB; the adsorption of NH2-UIO@L2 on MO followed the Dubinin-Radushkevich and pseudo-second-order models, and the adsorption on MB followed the Temkin and pseudo-second-order models. Hydrogen bonds, π-π interactions, and pore filling are all implicated in the removal of MO and MB. In particular, the electrostatic attraction between MB and MO improves the adsorption efficiency of NH2-UIO@L2 on MB. NH2-UIO@L2 has good reusability, maintaining an adsorption efficiency of 97.66 % for MO and up to 99.15 % for MB after six cycles. Its simple preparation and superior adsorption suggest that NH2-UIO@L2 has considerable potential to remove organic dyes from wastewater.

Efficient and Selective Removal of Organic Cationic Dyes by Peel of Brassica juncea Coss. var. gemmifera Lee et Lin-Based Biochar

The design and preparation of cheaper, greener and more efficient adsorbents is essential for the removal of pollutants by adsorption. In this study, biochar was prepared from peel of Brassica juncea var. gemmifera Lee et Lin (PoBJ) using a facile, low-temperature and vacuum pyrolysis, and the adsorption mechanism toward organic dyes in aqueous solution was elucidated. The adsorbent was characterized by XPS, FT-IR and SEM, and zeta potential techniques. The adsorption ability of PoBJ biochar for cationic dyes (methylene blue, brilliant green, calcein-safranine, azure I, rhodamine B), anionic dyes (alizarin yellow R), and neutral dyes (neutral red) revealed that the biochar exhibited adsorption selectivity toward cationic dyes. The effects of different factors on the adsorption performance of PoBJ biochar, as well as the adsorption kinetics and thermodynamics, were further investigated by using methylene blue as the model adsorbate. These factors included temperature, pH, contact time and dye concentration. The experimental results showed that BJ280 and BJ160 (prepared at 280 °C and 160 °C, respectively) possessed relatively higher adsorption capacity of 192.8 and 167.40 mg g^-1 for methylene blue (MB), respectively, demonstrating the possibility of utilization of PoBJ biochar as a superior bio-adsorbent. The experimental data of BJ160 toward MB were correlated with various kinetic and isothermal models. The results indicated that the adsorption process was consistent with the Langmuir isotherm model and nonlinear pseudo-second-order kinetic model. Thermodynamic parameters indicated that the adsorption of MB onto BJ160 was exothermic. Thus, the low-temperature prepared PoBJ biochar was an environmentally friendly, economic and efficient cationic dye adsorbent.

Design and preparation of carbon material catalyst modified with metal framework and sulfonate for biochar generation from low-temperature directional pyrolysis of kitchen waste: Mechanism and performance

In order to reduce the pyrolysis temperature during the process of directional conversion from kitchen waste (KW) into aromatic biochar, a kind of catalyst was prepared with carbon material coated with tri-metallic oxide (Fe₂O₃, MgO and Al₂O₃) combining with sulfonic acid groups (CMO@SA) according to KW compositions. The aromaticity of KW pyrolysis biochar (KWB) increased when the temperature ranged from 170 to 210 °C. The catalytic pyrolysis temperature of KW reduced from 500 to 190 °C for biochar generation with similar aromaticity due to amendment of CMO@SA. The maximum adsorption capacity of catalytic pyrolysis KWB was 160.23 mg/g for dyeing wastewater, which was equivalent to biochar generated at 500 °C. The decrease of pyrolysis temperature was attributed to the reduction of bonds fracture activation-energy among CH, CC and CO under the catalytic function. The catalytic activity and recovery of CMO@SA kept at 92 % and 90 % after five recycle.

Biochar Obtained from Caryocar brasiliense Endocarp for Removal of Dyes from the Aqueous Medium

Given the increase in environmental pollution, especially of water, the emergence of studies that seek to develop strategies to mitigate/treat such effects have gained prominence in the world scientific community. Among the numerous adsorption processes, those made from biochar production stand out. This study analyzed the adsorption properties of the blue methylene model dye in the aqueous solution of biochar and activated biochar developed from pequi (Caryocar brasiliense) endocarp. The biochar was characterized, before and after adsorption, by infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffractometry (XRD), and thermogravimetric analysis (TG). The surface load of the materials was performed by the point of zero charge (pH_PZC) method. The study also included analyses of contact time parameters and adsorbed concentration in the adsorption process. Morphological analysis showed that a more significant and profound number of fissures and pores appeared in the activated biochar compared to the biochar. Residual mass analysis evidenced that biochar lost about 15% more mass than the activated biochar, indicating that activation occurred satisfactorily. The adsorption process was well adjusted by pseudo-second-order kinetics and Langmuir's isothermal model. The activated biochar achieved an excellent adsorption capacity of 476.19 mg.g^-1, thus demonstrating to be a sound system for removing dyes from an aqueous medium.

Magnetic Activated Biochar Fe3O4-MOS Made from Moringa Seed Shells for the Adsorption of Methylene Blue

In recent years, more and more biochars have been employed to treat dye wastewater. In order to increase the utilization of moringa seed shell resources and enrich the removal method of methylene blue (MB) in solution, in the current study, the magnetic moringa seed shells biochar was prepared through ultrasonic-assisted impregnation and pyrolysis, while Fe3O4 was used to activate the material to obtain adsorption (Fe3O4-MOS). The prepared adsorbents were characterized by SEM-EDS, XRD, XPS, FTIR, N2 adsorption and desorption and VSM. Under the suitable experimental conditions, the removal rate can be close to 100% and the maximum adsorption capacity of MB could be 219.60 mg/g. The Freundlich model provided a good match to the data presented by the adsorption isotherm, and the adsorption of MB on Fe3O4-MOS was a spontaneous and endothermic reaction. Study of the mechanism indicated that pore adsorption, electrostatic interaction, hydrogen bond, and π-π interaction were the major adsorption mechanisms. After five cycles, it was found that Fe3O4-MOS had a high removal rate for MB, which was close to 90%. This work provides a new idea for moringa seed shells and the results confirm that Fe3O4-MOS has substantial potential for dye wastewater treatment.

Characteristics and aqueous dye removal ability of novel biosorbents derived from acidic and alkaline one-step ball milling of hickory wood

New classes of biosorbents are needed for various environment remediation applications. Thus, a facile and benign approach to synthesize porous biosorbents was developed using acidic or alkaline one-step ball milling of hickory wood biomass (AcBH and AlBH, respectively) without any external heat treatment, and their properties were compared. AcBH and AlBH were richer in O-containing functional groups, had enhanced porous structure and greater ability to remove crystal violet (CV, 476.4 mg g^-1) and Congo red (CR, 221.8 mg g^-1) dyes from aqueous solution, respectively, relative to hickory wood ball milled at neutral pH. Freundlich isotherm and pseudo second order kinetic models best fitted CR and CV adsorption onto biosorbents, indicating a mainly surface complexation adsorption mechanism. Further, both sorbents exhibited excellent stability and dye adsorption reusability. These results demonstrate that acidic and alkaline one-step ball milling is a facile and efficient approach for converting wood biomass into environmentally friendly biosorbents.

Functionalized biochars: Synthesis, characterization, and applications for removing trace elements from water

Biochar (BC) has been recognized as an effective adsorbent to remove trace elements (TEs) from water. However, low surface functionality and small pore size can limit the adsorption ability of pristine biochar. These limitations can be addressed by using functionalized biochars which are developed by physical, chemical, or biological activation of biochar to improve their physico-chemical properties and adsorption efficiency. Despite the large amount of research concerning functionalized biochars in recent decades, to our knowledge, no comprehensive review of this topic has been published. This review focuses solely on the synthesis, characterization, and applications of functionalized/engineered biochars for removing TEs from water. Firstly, we evaluate the synthesis of functionalized biochars by physical, chemical, and biological strategies that yield the desired properties in the final product. The following section describes the characterization of functionalized biochars using various techniques (SEM, TEM, EDS, XRD, XANES/NEXAFS, XPS, FTIR, and Raman spectroscopy). Afterward, the role of functionalized biochars in the adsorption of different TEs from water/wastewater is critically evaluated with an emphasis on the factors affecting sorption efficiency, sorption mechanisms, fate of sorbed TEs from contaminated environments and associated challenges. Finally, we specifically scrutinized the future recommendations and research directions for the application of functionalized biochar. This review serves as a comprehensive resource for the use of functionalized biochar as an emerging environmental material capable of removing TEs from contaminated water/wastewater.

A Novel Low-Cost Bio-Sorbent Prepared from Crisp Persimmon Peel by Low-Temperature Pyrolysis for Adsorption of Organic Dyes

In order to properly reuse food waste and remove various contaminants from wastewater, the development of green, sustainable and clean technologies has demonstrated potential in the efficient inhibition of secondary pollution to the environment. In this study, an economical and green method was used to prepare biochar from crisp persimmon peel (CPP) using flash-vacuum pyrolysis at different temperatures (200–700 °C; referred to as CPP200–CPP700). CPP200 has high polarity, low aromaticity and high oxygen-containing functional groups that exhibit superior MB adsorption capabilities. CPP200 that was prepared at a relatively low temperature of 200 °C exhibited a high adsorption capacity of 59.72 mg/g toward methylene blue (MB), which was relatively higher than that for alizarin yellow R (4.05 mg/g) and neutral red (39.08 mg/g), indicating that CPP200 possesses a higher adsorption selectivity for cationic dyes. Kinetics investigation revealed that the kinetic data of CPP200 for the adsorption of MB was better fitted by a linear pseudo-second-order model. Isothermal studies indicated that the linear Langmuir model was more suitable for describing the adsorption process. The adsorption thermodynamics illustrated that the adsorption of MB onto CPP200 was spontaneous and endothermic. EDS and IR analyses of CPP200 for both pre- and post-adsorption of MB showed that electrostatic interactions between oxygen-containing groups on biochar and target MB dominated the adsorption procedure, in addition to hydrogen bonding interactions. Reusability tests confirmed the excellent regeneration characteristics of CPP200, indicating that CPP200 may be used as a green, sustainable, highly efficient and recyclable adsorbent for the selective removal of cationic organic dyes.

Surface Modification of Biochar for Dye Removal from Wastewater

Nowadays, biochar is being studied to a great degree because of its potential for carbon sequestration, soil improvement, climate change mitigation, catalysis, wastewater treatment, energy storage, and waste management. The present review emphasizes on the utilization of biochar and biochar-based nanocomposites to play a key role in decontaminating dyes from wastewater. Numerous trials are underway to synthesize functionalized, surface engineered biochar-based nanocomposites that can sufficiently remove dye-contaminated wastewater. The removal of dyes from wastewater via natural and modified biochar follows numerous mechanisms such as precipitation, surface complexation, ion exchange, cation–π interactions, and electrostatic attraction. Further, biochar production and modification promote good adsorption capacity for dye removal owing to the properties tailored from the production stage and linked with specific adsorption mechanisms such as hydrophobic and electrostatic interactions. Meanwhile, a framework for artificial neural networking and machine learning to model the dye removal efficiency of biochar from wastewater is proposed even though such studies are still in their infancy stage. The present review article recommends that smart technologies for modelling and forecasting the potential of such modification of biochar should be included for their proper applications.

Cellulose-based bio-adsorbent from TEMPO-oxidized natural loofah for effective removal of Pb(II) and methylene blue

Excessive discharge of inorganic and organic contaminants in water poses a serious threat to the ecosystems. However, most synthetic adsorbents lack cost-effectiveness in terms of preparation. Interestingly, loofah sponge (LS) was a natural absorbent that could effectively remove pollutions in wastewater, but its adsorption capacity is barely satisfactory. Herein, we present a novel strategy of TEMPO-oxidized loofah sponge (TOLS) to boost the adsorption performance of LS. The batch experiments demonstrated that the maximum removal capacity of TOLS for Pb(II) and methylene blue (MB) was 96.6 mg/g and 10.0 mg/g, respectively, which were 3.5 and 1.3 times that of pristine LS. Notably, the continuous-flow reaction testing of the mixed solution revealed that the elimination rate of Pb(II) and MB was still better than 90 % even after 16 h. Such excellent performance was benefit from the enhanced specific surface area and surface carboxyl content of TOLS. This work offers new insights into the rational development of multifunctional and inexpensive cellulose-based bio-adsorbents for wastewater remediation.

Preparation, characterization, and application of modified magnetic biochar for the removal of benzotriazole: process optimization, isotherm and kinetic studies, and adsorbent regeneration

The adsorption of benzotriazole (BTA) by chemically modified magnetic biochar (MMBC) as a cheap and abundant biosorbent was investigated and optimized using response surface methodology (RSM). Initially, the MMBC composite was synthesized and characterized by scanning electron microscopy (SEM) energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and Brunauer-Emmett-Teller (BET) techniques. The characterization results confirmed the existence of Fe₃O₄ in the composite structure, which had uniformly dispersed over biochar (BC) with porous texture. Moreover, the presence of Zn and Cl elements in EDX analysis indicated that the magnetic biochar (MBC) had been modified successfully. The effects of chemical modification methods on the adsorption capacity of magnetic biochar were investigated. Maximum BTA removal efficiency was demonstrated by MMBC, modifying using ZnCl₂ (>99%). Optimization was carried out based on reaction time, BTA concentration and the concentration of adsorbent. Optimum experimental conditions for the removal of BTA from aqueous solutions were found to be 35 min of reaction time, 0.55 g/L of adsorbent, and 50 mg/L of initial BTA concentration. At these optimal conditions, the predicted BTA adsorption efficiency was 92.6%. The adsorption process followed the Avrami fractional-order reaction kinetic and the Langmuir adsorption isotherm with the maximum adsorption capacity of 563.1 mg/g. The values of thermodynamic parameters demonstrated that the adsorption of BTA on ZnCl₂-MBC is endothermic and spontaneous. Under optimum usage of MMBC, the adsorptive removal efficiency of BTA non-significantly decreased from 99.2 to 93.9% after the 5th cycle. Thus, MMBC can be recommended as an environmentally friendly and cost-effective adsorbent to remove micropollutants from water.

Recent Developments in the Application of Bio-Waste-Derived Adsorbents for the Removal of Methylene Blue from Wastewater: A Review

Over the last few years, various industries have released wastewater containing high concentrations of dyes straight into the ecological system, which has become a major environmental problem (i.e., soil, groundwater, surface water pollution, etc.). The rapid growth of textile industries has created an alarming situation in which further deterioration to the environment has been caused due to substances being left in treated wastewater, including dyes. The application of activated carbon has recently been demonstrated to be a highly efficient technology in terms of removing methylene blue (MB) from wastewater. Agricultural waste, as well as animal-based and wood products, are excellent sources of bio-waste for MB remediation since they are extremely efficient, have high sorption capacities, and are renewable sources. Despite the fact that commercial activated carbon is a favored adsorbent for dye elimination, its extensive application is restricted because of its comparatively high cost, which has prompted researchers to investigate alternative sources of adsorbents that are non-conventional and more economical. The goal of this review article was to critically evaluate the accessible information on the characteristics of bio-waste-derived adsorbents for MB’s removal, as well as related parameters influencing the performance of this process. The review also highlighted the processing methods developed in previous studies. Regeneration processes, economic challenges, and the valorization of post-sorption materials were also discussed. This review is beneficial in terms of understanding recent advances in the status of biowaste-derived adsorbents, highlighting the accelerating need for the development of low-cost adsorbents and functioning as a precursor for large-scale system optimization.

Iron/titanium oxide-biochar (Fe2TiO5/BC): A versatile adsorbent/photocatalyst for aqueous Cr(VI), Pb2+, F- and methylene blue

This is the first report of the metal Fe-Ti oxide/biochar (Fe₂TiO₅/BC) composite for simultaneous removal of aqueous Pb²⁺, Cr⁶⁺, F^- and methylene blue (MB). Primary Fe₂TiO₅ nano particles and aggregates were dispersed on a high surface area Douglas fir BC (∼700 m²/g) by a simple chemical co-precipitation method using FeCl₃ and TiO(acac)₂ salts treated by base and heated to 80 °C. This was followed by calcination at 500 °C. This method previously was used without BC to make the neat mixed oxide Fe₂TiO₅, exhibiting a lower energy band gap than TiO₂. Adsorption of Cr(VI), Pb(II), fluoride, and MB on Fe₂TiO₅/BC was studied as a function of pH, equilibrium time, initial adsorbate concentration, and temperature. Adsorption isotherm studies were conducted at 5, 25, and 45 ℃ and kinetics for all four adsorbates followed the pseudo second order model. Maximum Langmuir adsorption capacities for Pb²⁺, Cr⁶⁺, F^- and MB at their initial pH values were 141 (pH 2), 200 (pH 5), 36 (pH 6) and 229 (pH 6) mg/g at 45 ℃ and 114, 180, 26 and 210 mg/g at 25 ℃, respectively. MB was removed from the water on Fe₂TiO₅/BC by synergistic adsorption and photocatalytic degradation at pH 3 and 6 under UV (365 nm) light irradiation. Cr⁶⁺, Pb²⁺, F^-, and MB each exhibited excellent removal capacities in the presence of eight different competitive ions in simulated water samples. The removal mechanisms on Fe₂TiO₅/BC and various competitive ion interactions were proposed. Some iron ion leaching at pH 3 catalyzed Photo-Fenton destruction of MB. Fe₂TiO₅, BC, and Fe₂TiO₅/BC bandgaps were studied to help understand photocatalysis of MB and to advance supported metal oxide photodegradation using smaller energy band gaps than the larger bandgap of TiO₂ for water treatment. A long range goal is to photocatalytically destroy some sorbates with adsorbents to avoid the need for regeneration steps.

Removal of methyl orange from water by Fenton oxidation of magnetic coconut-clothed biochar

Water pollution has become a serious environmental problem to date. Advanced oxidation processes (AOP) have been widely applied in water treatments.

Synthesis, Characterization, and Dye Removal of ZnCl2-Modified Biochar Derived from Pulp and Paper Sludge

In this study, pulp sludge-derived biochar synthesized through modification with ZnCl₂ under multistep pyrolysis conditions was investigated for the effective removal of methylene blue (MB) from aqueous solution. Results showed that when the Zn2PT350-700 dosage was 10 mg, the largest adsorption amount of MB was 590.20 mg/g within 24 h under pH = 8. Kinetics and thermodynamics revealed that the adsorption process of MB can be described by the Freundlich isotherm model and the pseudo-second-order kinetic model, which means that multilayer sorption occurred on the heterogeneous surface of Zn2PT350-700. The analysis of the adsorption mechanism showed that electrostatic attraction between the deprotonated functional groups and MB⁺, cation exchange, and π-electron interaction played a major role in MB adsorption, followed by physical adsorption. After six cycles of desorption-adsorption, Zn2PT350-700 still maintained good adsorption performance. All results demonstrated that Zn2PT350-700 could perform as promising adsorbents for efficient MB removal from wastewater. Using biochar from paper and pulp sludge for wastewater remediation is an ingenious method, which can reduce the environmental and health risks related to industrial waste disposal, while providing remediation of water contaminated with industrial dye effluents.

Petroleum oil and products recovery from oily sludge: Characterization and analysis of pyrolysis products

Oily sludge (OS) has attracted special interest because of its hazardous nature and high potential as an energy resource. This study investigated the oil recovery from OS by thermal cracking and catalytic pyrolysis. The oil yield increased when the temperature exceeded 450 °C and reached a maximum (76.84 wt%) at 750 °C. Catalysts significantly improved the quality of oil produced during catalytic pyrolysis. Aromatic hydrocarbons were dominant (10.01-52.69%) in pyrolysis oil (PO) from OS catalytic pyrolysis, and the catalysts significantly reduced the presence of oxygen heterocycles. In addition, KOH and CaO reduced the I_D (D-band peak intensity)/I_G (G-band peak intensity) of OS char (OC) and increased the degree of graphitization. Owing to its higher iodine adsorption value and methylene blue (MB) adsorption value, OC exhibits potential as an adsorbent. The environmental assessment and potential applications of OC, along with possible reaction mechanisms and kinetic characteristics, are also discussed.

Kinetics, Thermodynamics, and Isotherms of Methylene Blue Adsorption Study onto Cassava Stem Activated Carbon

Water treatment using activated carbon is widely accepted, despite its high production cost. Therefore, this study was aimed to investigate the potential of cassava stem in activated carbon form for methylene blue (MB) dye uptake from water. Raw cassava stem (RCS) was also utilized to evaluate the difference between cassava stem in its raw form and after being converted to the activated carbon (ACS). The MB adsorption from water using the RCS and ACS was done in this study. The batch adsorption study showed fast MB uptake by ACS at 60 min contact time, while higher adsorbent dosage and higher pH contributed to higher adsorption percentage. The thermodynamic study showed positive values of ∆H° of ACS, indicating that the adsorption process of MB was endothermic. Meanwhile, the negative value of ∆G° showed that the adsorption processes of MB were spontaneous. The thermodynamic study showed higher fitting to Langmuir isotherm, with data from the kinetic study showing better pseudo-second-order equation fitting, which suggests the chemisorption process had happened. The highest adsorption recorded by ACS was 384.61 mg/g, indicating the possibility of cassava stem as the lower cost raw material for activated carbon production with excellent adsorption characteristics.

Mechanisms and adsorption capacities of hydrogen peroxide modified ball milled biochar for the removal of methylene blue from aqueous solutions

In this work, hickory chip biochars developed at distinctive pyrolysis temperatures were ball milled (BMHC) and then post-modified with a 10% hydrogen peroxide (H₂O₂) solution to obtain a set of novel sorbents (BMHC-H₂O₂). The specific surface area (SSA) was dramatically increased after ball-milling while the hydroxyl and carboxyl groups on the surface of the biochars were further increased through H₂O₂ modification. Additionally, thermal stability of the biochar treated with ball-milling was not greatly reduced by H₂O₂ modification and hydrodynamic radius was decreased. Ball milling enhanced the adsorption efficiency to methylene blue (MB) by the biochar, and this ability was further increased by H₂O₂ modification, because of the increasing in oxygen-containing functional groups (OCFG) to interact with MB. The rate of MB adsorption to BMHC-H₂O₂ was faster than that of BMHC, reaching equilibrium after about 6 h. Among adsorbents tested, the 450 °C BMHC-H₂O₂ had the greatest MB adsorption capacity (310 mg g^-1).

Characterization of pruned tea branch biochar and the mechanisms underlying its adsorption for cadmium in aqueous solution

In the present study, discarded pruned tea branch was used to prepare a new biochar, and the physicochemical properties and adsorption characteristics were investigated by characterization and batch experiments. With increasing pyrolysis temperature from 400 to 800 °C, the yield, specific surface area, and acidic functional groups had significant differences. The optimum adsorption conditions were determined as pH = 6 and dosage of 2 g L^-1. The pseudo-second-order kinetic and Langmuir isothermal model could fit well to the adsorption data, which showed that the adsorption process was dominated by monolayer chemical adsorption. The highest adsorption property (74.04 mg g^-1) was obtained by the pyrolysis of tea branch biochar (TBB) at 700 °C owing to the adsorption mechanisms, including surface complexation, precipitation, metal ion exchange, and Cd²⁺-π interaction. After five cycles of desorption, biochar still showed superior adsorption (80%). Hence, the TBB acted as a regenerable adsorbent for treating Cd²⁺-containing wastewater.

Aquaculture wastewater treatment through microalgal. Biomass potential applications on animal feed, agriculture, and energy

The use of microalgae to remediate raw effluent from brown crab aquaculture was evaluated by performing batch mode growth tests using separately the microalgae Chlorella vulgaris (Cv), Scenedesmus obliquus (Sc), Isochrysis galbana (Ig), Nannocloropsis salina (Ns), and Spirulina major (Sp). Removal efficiencies in batch growth were 100% for total nitrogen and total phosphorus for all microalgae. Chemical oxygen demand (COD) remediations were all above 72%. Biomass productivity varied from 20.9 mg L^-1 day^-1 (N. salina) to 146.4 mg L^-1 day^-1 (C. vulgaris). The two best performing algae were C. vulgaris and S. obliquus and they were tested in semi-continuous growth, reaching productivities of 879.8 mg L^-1 day^-1 and 811.7 mg L^-1 day^-1, respectively. The bioremediation of the effluent was tested with a transfer system consisting of three independent containers and compared with the use of a single container. The single container had the same capacity and received weekly the same volume of effluent as the three containers together. The remediation capacity of the 3 containers was much higher than the single one. The supplementation with NaNO₃ was tested to improve the nutrient removal microalgae' capacity, with positive results. The removal efficiencies were 100% for total nitrogen and total phosphorus and higher than 96% for COD. The obtained C. vulgaris and S. obliquus biomass were composed of 31 and 35% proteins, 6 and 8% lipids, 39 and 30% carbohydrates, respectively. The composition of these biomass suggest that it can be used as novel and sustainable ingredients in aquaculture feeds. The algal biomass of Cv and Sc were used as biostimulants in the germination of wheat and watercress, and very promising results were attained, with increases in the germination index for Cv and Sc of 175% and 48% in watercress and 84% and 98% in wheat, respectively. The biomasses of Cv and Sc were also subjected to a torrefaction process with 72.5 ± 1.7% char yields. The obtained biochars were tested as biostimulants for germination seeds (wheat and watercress) and as bio-adsorbent of dye solutions.

An Efficient Strategy for Enhancing the Adsorption Capabilities of Biochar via Sequential KMnO4-Promoted Oxidative Pyrolysis and H2O2 Oxidation

In this study, sequential KMnO4-promoted oxidative pyrolysis and H2O2 oxidation were employed to upgrade the adsorption capacities of durian shell biochar for methylene blue (MB) and tetracycline (TC) in an aqueous solution. It was found that the KMnO4/H2O2 co-modification was greatly influenced by pyrolysis temperature and the optimal temperature was 300 °C. Moreover, a low concentration of H2O2 enabled the improvement of the adsorption capabilities greatly with the catalysis of pre-impregnated manganese oxides, addressing the shortcoming of single H2O2 modification. The co-modified biochar exhibited high adsorption capabilities for MB and TC, remarkably surpassed KMnO4- and H2O2- modified biochars as well as pristine biochar. The increase of adsorption capabilities could be mainly contributed to the incorporation of MnOx and carboxyl by KMnO4-promoted oxidative decomposition and Mn-catalyzed H2O2 oxidation. This would provide a novel and efficient method for preparing highly adsorptive biochar using sequential KMnO4-promoted oxidative pyrolysis and H2O2 oxidation.

Promoting adsorption of organic pollutants via tailoring surface physicochemical properties of biomass-derived carbon-attapulgite

Biomass-derived carbon-attapulgite adsorbent was developed for organic pollutants removal. All the batch assays were performed to evaluate the effects of organic components, contact time, and initial concentration of organic pollutants on the adsorption performance of the as-prepared adsorbent. The samples were characterized via Brunauer-Emmett-Teller (BET), Fourier transform infrared (FTIR), X-ray diffractometer (XRD), and scanning electron microscopy (SEM). The results demonstrated that the acid-treated carbon-attapulgite adsorbent (H-ATP/BC) showed a large specific surface area (237 m² g^-1) and possessed abundant oxygen-containing functional groups and silicon-oxygen bonds (i.e., O-Si-O and O-Si), which provided more active sites and conduced to the adhesive of organic pollutants. Both physical adsorption and chemical adsorption were involved in the adsorption process, and competitive adsorption occurred when two or more target pollutants coexist. Especially, phenol and/or aniline with an aromatic ring were much more likely to adhere to the H-ATP/BC surface than pyridine, and the selectivity order of H-ATP/BC for these pollutants was phenol > aniline > pyridine. From the model fitting, it was observed that the adsorption data could be described well by a pseudo-second-order model and Freundlich isotherms. The theoretical maximum phenol, aniline, and pyridine adsorption capacities of the H-ATP/BC were 14.31 mg g^-1, 15.21 mg g^-1, and 20.74 mg g^-1, respectively. Comparison among the commercial adsorbents price also illustrated that H-ATP/BC could be a promising material for efficient treatment of organic pollutants.Graphical abstract.

High effective adsorption of Pb(II) from solution by biochar derived from torrefaction of ammonium persulphate pretreated bamboo

Biochar was prepared by torrefaction of ammonium persulphate pretreated bamboo (labeled as APBC) and applied into elimination of Pb(II) from water solutions. APBC was characterized by N₂ adsorption-desorption isotherms, elemental and Zeta potential analyses, SEM-EDS, XPS, and FTIR. Abundant N- and O-containing groups appeared atop APBC. Batch sorption assays revealed that APBC had high affinity and strong sorption ability towards Pb(II). The high Pb(II) adsorbing ability was attributed to the high contents of N- and O-containing functional groups of APBC. The adsorption mechanism mainly occurred by inner-sphere surface complexation. Hence, torrefaction of ammonium persulphate pretreated bamboo is a promising strategy for producing efficient biochar that is applicable for industrial wastewater treatment.

Green synthesis of poly(pyrrole methane) for enhanced adsorption of anionic and cationic dyes from aqueous solution

The presence and accumulation of dyestuff in the environment is posing great harm to human beings. In this study, a novel poly(pyrrole methane) (PPm) adsorbent with abundant OH was greenly synthesized via a facile polymerization method. Its physicochemical properties were characterized in detail. Furthermore, the adsorption performance of PPm for anionic dye (acid red G, ARG) and cationic dye (methylene blue, MB) was comparatively studied with a typical dye adsorbent (polyprrrole, PPy). The results revealed that the adsorption of ARG or MB onto PPm followed pseudo-second-order model and Langmuir mode. The adsorption processes were endothermic and spontaneous. The maximum capacities of PPm to adsorb ARG and MB were 555.56 mg/g and 99.11 mg/g, which were about 10 and 2 times higher than that of PPy, respectively. PPm could be reused for 5 cycles without a significant decrease of its adsorption rate. The adsorption of ARG and MB is mainly attributed to electrostatic interaction and hydrogen bonding between ARG or MB and OH in PPm. Additionally, ARG could be adsorbed by ion exchange with the doped Cl^- in PPm. Therefore, this study provides a new strategy to synthesis efficient adsorbent for the removal of both anionic and cationic dyes.

Surface Functionalization of Biochar from Oil Palm Empty Fruit Bunch through Hydrothermal Process

The use of biochar as an adsorbent for wastewater treatment purposes has been hindered due to its lower surface area compared to activated carbon. Current research on increasing surface functional groups on biochar surfaces to improve its adsorption performance suggests using high chemical concentration and long period of modification. This study solves these problems by focusing on improving surface functionalities of biochar via the hydrothermal functionalization process. Oil palm empty fruit bunch biochar was functionalized using autoclave with nitric acid as the functionalization agent. Functionalized biochar properties such as Brunauer–Emmett–Teller (BET) surface area and surface functional groups were analyzed and compared with untreated biochar. Fourier Transform Infrared (FTIR) spectroscopic analysis shows a significant increase in absorption by oxygen functional groups and is corroborated with energy dispersive X-ray (EDX) analysis. The process does not result in any major change in surface morphology and reduction in surface area value. Methylene blue (MB) adsorption test shows 7 times increase in adsorption performance. These results show that the simple hydrothermal functionalization process successfully functionalizes the biochar surface and improves its performance without affecting its surface area at lower concentration, and shorter time compared to previous studies. This result, with future large-scale experimentation using real-life equipment in palm oil mills, would provide a better technology that can be implemented in the industry.

A critical review of the production and advanced utilization of biochar via selective pyrolysis of lignocellulosic biomass

Biochar is a carbon-rich product obtained from the thermo-chemical conversion of biomass. Studying the evolution properties of biochar by in-situ modification or post-modification is of great significance for improving the utilisation value of lignocellulosic biomass. In this paper, the production methods of biochar are reviewed. The effects of the biomass feedstock characteristics, production processes, reaction conditions (temperature, heating rate, etc.) as well as in-situ activation, heteroatomic doping, and functional group modification on the physical and chemical properties of biochar are compared. Based on its unique physicochemical properties, recent research advances with respect to the use of biochar in pollutant adsorbents, catalysts, and energy storage are reviewed. The relationship between biochar structure and its application are also revealed. It is suggested that a more effective control of biochar structure and its corresponding properties should be further investigated to develop a variety of biochar for targeted applications.

Synthesis of silica-composited biochars from alkali-fused fly ash and agricultural wastes for enhanced adsorption of methylene blue

Two types of silica-composited biochars were prepared by mixing swine manure or rice straw with alkali-fused fly ash (AFFA) followed by pyrolysis. A 10% (w/w) AFFA modification improved the specific surface area, pore volume, and average pore size of the biochars. Certain surface oxygen-containing functional groups (i.e., -OH and CO) in the biochars were protected, and silicon-oxygen bonds (i.e., O-Si-O and OSi) were strengthened considerably by AFFA modifications during high-temperature pyrolysis. The adsorption capacity of biochar for methylene blue (MB) was enhanced after AFFA modification, and a modified biochar with the highest adsorption capacity was prepared at a pyrolysis temperature of 700 °C, pyrolysis holding time of 2 h, and an AFFA proportion of 10%. The MB adsorption capacity of the modified biochars significantly increased when the pH of the solution increased (from 3 to 13). The adsorption data were well described by a pseudo-second-order model and Langmuir isotherms. The maximum MB adsorption capacities of the modified swine manure and rice straw biochars were 143.76 mg/g and 131.58 mg/g, respectively. The adsorption capacities of the AFFA-modified biochars were 10.7-112.3% higher than those of the unmodified biochars. The enhanced MB adsorption capacities of the former appear to be attributed to their increased specific surface areas, increased porosities, strong oxygen-containing functional groups, and high contents of exchangeable sodium ions. These results indicate that industrial and agricultural wastes can be reused to produce novel silica-composited biochars with high MB removal capacity. Accordingly, these biochars could be effectively used to treat wastewater and thus to mitigate solid waste disposal-related problems.

Removal of methylene blue from aqueous solutions by biochar prepared from the pyrolysis of mixed municipal discarded material

This paper investigates the adsorption of organic compounds in aqueous solution to biochar adsorbent, using methylene blue as an indicator for adsorption. Biochar was produced by the pyrolysis of mixed municipal discarded material in an innovative heat pipe reactor, the pyrolysis temperature was held at 300°C for 12 h. Biochar produced under these conditions was found to have oxygen containing functional groups that are beneficial to the adsorption of methylene blue as well as graphitic structures suggesting potential sites for π-π interactions with methylene blue. Methylene Blue followed the pseudo second order kinetic model with higher R² values than both the pseudo first order kinetic and intraparticle diffusion models. The adsorption also closely fit the Langmuir isotherm rather than the Freundlich model, suggesting monolayer adsorption rather than multilayer adsorption. Maximum adsorption capacity was observed at 7.2 mg/g for initial concentration of 100 mg/l Methylene blue in aqueous solution. The amount of Methylene blue adsorbed increased with increasing initial concentration as expected. The adsorption mechanisms are likely π-π interactions between methylene blue and the graphitic structures in the biochar which are shown to be present in Raman spectroscopy, as well as electrostatic attraction and ionic bonding between negatively charged surface sites on the char and the positive charge on the dissolved methylene blue molecules. The results show that biochar obtained from mixed waste could be employed as a low-cost and effective tool in water treatment for the removal of basic dyes and potentially other organic impurities.

Magnetic activated biochar nanocomposites derived from wakame and its application in methylene blue adsorption

In this work, magnetic wakame biochar nanocomposites for the first time had been synthesized to investigate their adsorption to methylene blue dye. As-prepared magnetic biochar samples were obtained by the impregnation method to load nickel on wakame biochar via one-step carbonization with activation agent KOH at 800 °C. The prepared samples were characterized by BET, XRD, FTIR, Raman, SEM, TEM and so on. The results exhibited that the maximum adsorption capacity of BW(Ni)0.5 to methylene blue could reach 479.49 mg/g at 20 °C. The adsorption behavior was more suitable for Langmuir isotherm equation and the kinetic data were most consistent with the pseudo second-order model. And also, the adsorption reaction was a spontaneous and endothermic process. After five cycles, it was found that BW(Ni)0.5 had a high adsorption capacity for methylene blue (117.58 mg/g). This study demonstrated that wakame biochar could have great potential in dye wastewater treatment.