Pt nanoparticle-based highly sensitive platform for the enzyme-free amperometric sensing of H2O2

Precursor-Derived Sensing Interdigitated Electrode Microstructures Based on Platinum and Nano Porous Carbon

Interdigital electrodes were prepared using nanoimprint lithography and piezoelectric inkjet printing. These processes are simpler and more cost-effective than the industrially used electron beam lithography because of their purely mechanical process step. For the investigation of material dependence, platinum as well as carbon electrodes were fabricated. Afterwards electrodes with various line widths and spacings were tested for the application as a chemiresistive sensor for ferrocenyl-methanol and the influence of the gap-width and conductor cross-section on the sensitivity was investigated. The general suitability of the systems for the production of such structures could be confirmed. Structures with a limit of detection (LOD) down to 1.2 μM and 35.9 μM could be produced for carbon and platinum, respectively, as well as a response time of 3.6 s was achieved.

Platinum and palladium nanoparticles on boron-doped diamond for the electrochemical detection of hydrogen peroxide: a comparison study

Hydrogen peroxide (H2O2) plays a role in many facets - a household item, an important industrial chemical, a biomarker in vivo, and several others. For this reason, its measurement and quantification in a variety of media are important. While spectroscopic detection is primarily used for H2O2, electrochemical methods offer advantages in versatility, cost, and sensitivity. In this work, we investigate a 2-step surface metal nanoparticle (NP) modification for platinum (Pt) and palladium (Pd) on boron-doped diamond (BDD) electrodes for the detection of H2O2. Several parameters such as the metal salt concentration and electrodeposition charge in the 2-step modification were varied to find an optimum. Using cyclic voltammetry (CV), the BDD-PdNP electrode types were found to yield a sharper, more well-resolved H2O2 oxidation peak compared to the BDD-PtNP electrodes. Both metal NP electrode types significantly improved the response compared to the bare BDD electrode; a 150-200× improvement in sensitivity was observed across all modified electrode types. Calibration experiments were completed at both low and high concentration ranges in stagnant and flow-based solutions. The lowest limit of detection (LOD) obtained was 50 nM (5E-08 M) on a BDD-PdNP electrode modified with 1.0 mM PdCl2 to 5.0 mC in the wet chemical seeding and electrodeposition steps. 0.25 mM PdCl2 to 3.23 mC and 0.25 mM HPtCl6- to 3.23 mC also yielded a sufficient response for low-level H2O2, with LODs around 100 nM (1E-07 M). Overall, this work exemplifies the wide applicability of BDD and achieves sub-μM H2O2 LODs with a non-enzymatic electrode material.

A Non-enzymatic Hydrogen Peroxide Sensor with Enhanced Sensitivity Based on Pt Nanoparticles

The non-enzymatic electrochemical sensing platform for hydrogen peroxide by using Pt-based nanoparticle was investigated. The characterization of PtNiCo-NPs was done by XRD, TEM, HRTEM, EDS, and XPS. A simple drop-casting technique was used to fabricate the nanomaterial on FTO electrode. The amperometric and cyclic voltammetric results illustrated that PtNiCo-NPs on FTO had excellent electrochemical performance over other mono or bimetallic materials. The catalytic performance for H₂O₂ sensing based on PtNiCo-NPs possessed a wide linear range from 5 μM to 16.5 mM with a low detection limit of 0.37 μM and a good sensitivity of 1374.4 μA mM^-1 cm^-2 at a scan rate of 20 mV s^-1 (vs. Ag/AgCl). This work presents a new way to produce a ternary nanomaterial for H₂O₂ sensing with excellent electrochemical performance. In addition, the fabricated nanomaterial showed no interferences for common interfering agents, which indicates the high specificity of the sensor. The PtNiCo-NPs have excellent stability and good reproducibility in real samples.

Biofriendly molecular and protein release substrate with integrated piezoelectric motivation and anti-oxidative stress capabilities

Self-powered piezoelectrically active molecular or protein delivery devices have provoked great interest in recent years. However, electric fields used to promote delivery or healing may also induce the redox of water or oxygen to generate reactive oxygen species (ROS) and bring unintended oxidative pressure to the organism and harm biological functions. In addition, protein molecules are easily inactivated in the polymer reservoir matrix due to the pull of strong electrostatic effects. In this study, a multifunctional molecular delivery substrate was fabricated by integrating a piezoelectric-dielectric polymeric substrate, nanoscopic polyelectrolyte films and in-film deposited biomimetic porous CaP coating. The piezoelectric substrate promoted molecular release, and the mineralized coating effectively stored molecules or proteins and simultaneously eliminated ROS, reducing the oxidative stress response generated by oxidative pressure. The present work opens a new way for the development of multifunctional and biofriendly drug delivery devices.

Electrochemical sensor based on the Mn3O4/CeO2 nanocomposite with abundant oxygen vacancies for highly sensitive detection of hydrogen peroxide released from living cells

Based on the strategy of increasing the number of oxygen vacancies to improve the catalytic performance, we have developed a novel electrochemical sensor based on the multivalent metal oxides cerium dioxide and manganous oxide (Mn₃O₄/CeO₂) for reliable determination of extracellular hydrogen peroxide (H₂O₂) released from living cells. The Mn₃O₄/CeO₂ nanocomposite was characterized by high-resolution transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The electrochemical performance of the Mn₃O₄/CeO₂ nanocomposite modified glassy carbon electrode (Mn₃O₄/CeO₂/GCE) was investigated. Owing to the abundant oxygen vacancies and strong synergistic effect between the multivalent Ce and Mn, the sensor exhibited excellent catalytic activity and selectivity for the electrochemical detection of H₂O₂ with a low quantitation limit of 2 nM. Moreover, Mn₃O₄/CeO₂/GCE exhibited excellent reproducibility, repeatability, and long-term storage stability. Because of these remarkable analytical advantages, the constructed sensor was able to determine H₂O₂ released from living cells with satisfactory results. The results showed that the Mn₃O₄/CeO₂ sensor is a promising candidate for a nanoenzymatic H₂O₂ sensor with the possibility of applications in physiology and diagnosis.

Nanostructures in Hydrogen Peroxide Sensing

In recent years, several devices have been developed for the direct measurement of hydrogen peroxide (H2O2), a key compound in biological processes and an important chemical reagent in industrial applications. Classical enzymatic biosensors for H2O2 have been recently outclassed by electrochemical sensors that take advantage of material properties in the nano range. Electrodes with metal nanoparticles (NPs) such as Pt, Au, Pd and Ag have been widely used, often in combination with organic and inorganic molecules to improve the sensing capabilities. In this review, we present an overview of nanomaterials, molecules, polymers, and transduction methods used in the optimization of electrochemical sensors for H2O2 sensing. The different devices are compared on the basis of the sensitivity values, the limit of detection (LOD) and the linear range of application reported in the literature. The review aims to provide an overview of the advantages associated with different nanostructures to assess which one best suits a target application.

Smart materials-integrated sensor technologies for COVID-19 diagnosis

After the first case has appeared in China, the COVID-19 pandemic continues to pose an omnipresent threat to global health, affecting more than 70 million patients and leading to around 1.6 million deaths. To implement rapid and effective clinical management, early diagnosis is the mainstay. Today, real-time reverse transcriptase (RT)-PCR test is the major diagnostic practice as a gold standard method for accurate diagnosis of this disease. On the other side, serological assays are easy to be implemented for the disease screening. Considering the limitations of today's tests including lengthy assay time, cost, the need for skilled personnel, and specialized infrastructure, both strategies, however, have impediments to be applied to the resource-scarce settings. Therefore, there is an urgent need to democratize all these practices to be applicable across the globe, specifically to the locations comprising of very limited infrastructure. In this regard, sensor systems have been utilized in clinical diagnostics largely, holding great potential to have pivotal roles as an alternative or complementary options to these current tests, providing crucial fashions such as being suitable for point-of-care settings, cost-effective, and having short turnover time. In particular, the integration of smart materials into sensor technologies leverages their analytical performances, including sensitivity, linear dynamic range, and specificity. Herein, we comprehensively review major smart materials such as nanomaterials, photosensitive materials, electrically sensitive materials, their integration with sensor platforms, and applications as wearable tools within the scope of the COVID-19 diagnosis.

Gold nanoparticles plated porous silicon nanopowder for nonenzymatic voltammetric detection of hydrogen peroxide

A voltammetric approach was developed for the selective and sensitive determination of hydrogen peroxide using Au plated porous silicon (PSi) nanopowder modified glassy carbon electrode (GCE). The AuNPs-PSi hybrid structure was synthesized via stain etching procedure followed by an immersion plating method to deposit AuNPs onto PSi via a simple galvanic displacement reaction with no external reducing agent to convert Au³⁺ to Au⁰. The as-fabricated AuNPs-PSi catalyst was successfully characterized by XRD, Raman, FTIR, XPS, SEM, TEM and EDS techniques. Well crystalline nature of the as-fabricated hybrid structure with AuNPs size ranging from 5 to 40 nm was observed. The specific surface area and total pore volume for both PSi and AuNPs plated PSi were evaluated using N₂ adsorption isotherm technique. Cyclic voltammetry and electrochemical impedance spectroscopy techniques were applied to investigate the catalytic efficiency of AuNPs-PSi modified electrode compared to pure PSi/GCE and unmodified GCE. The sensing performance of the active material modified GCE was thoroughly examined with linear sweep voltammetry (LSV) and square wave voltammetry (SWV) techniques. The AuNPs-PSi/GCE exhibited a remarkable linear dynamic range between 2.0 and 13.81 mM (for LSV) and 0.5-6.91 mM for (SWV) with high sensitivity and low detection limit of 10.65 μAmM^-1cm^-2 and 14.84 μM for LSV, whereas 10.41 μAmM^-1cm^-2 and 15.16 μM using SWV techniques, respectively. The fabricated sensor electrode showed excellent anti-interfering ability in the presence of several common biomolecules as well as demonstrated good operational stability and reproducibility with low relative standard deviation. Moreover, the modified electrode showed acceptable recovery of H₂O₂ in a real sample analysis. Thus, the developed AuNPs-PSi hybrid nanomaterial represents an excellent electrocatalyst for the efficient detection and quantification of H₂O₂ by the electrochemical approach.

Enzyme-like electrocatalysis from 2D gold nanograss-nanocube assemblies

Nanotechnology's rapid development of nanostructured materials with disruptive material properties has inspired research for their use as electrocatalysts to potentially substitute enzymes. Herein, a novel electrocatalytic nanomaterial was constructed by growing gold nanograss (AuNG) on 2D nanoassemblies of gold nanocubes (AuNC). The resulting structure (NG@NC) was used for the detection of H₂O₂via its electrochemical reduction. The NG@NC electrode displayed a large active surface area, resulting in improved electron transfer efficiency. On the nanoscale, AuNG maintained its structure, providing high stability and reproducibility of the sensing platform. Our nanostructured electrode showed excellent catalytic activity towards H₂O₂ at an applied potential of -0.5 V vs Ag/AgCl. This facilitated H₂O₂ detection with excellent selectivity in an environment like human urine, and a linear response from 50 µM to 30 mM, with a sensitivity of 100.66 ± 4.0 μA mM^-1 cm^-2. The NG@NC-based sensor hence shows great potential in nonenzymatic electrochemical sensing.

Adsorption mechanism of Pt, Ag, Al, Au on GaAs nanowire surfaces from first-principles

The electronic and optical properties of metal (M) atoms adsorbed GaAs nanowires are systemically investigated utilizing first-principles calculations based on density functional theory. Different materials (M  =  Pt, Ag, Al and Au) and different coverages (1M, 2M, 3M and 4M) are considered to construct surface adsorption models. The calculations show that all metal-adsorbed GaAs nanowire surfaces are stable, and the difficulty of metal atom adsorption on nanowire surfaces follows the rule of Ag  >  Au  >  Al  >  Pt. In addition, the layer distance variation of nanowire surfaces after metal atom adsorption mainly take place near the outmost layer region. In 1M coverage case, the work function is reduced by Pt, Ag, Al adsorption, while increased by Au adsorption. Specially, Pt- and Al-adsorbed GaAs nanowire surfaces are direct band gap semiconductors, but Ag- and Au-adsorbed surfaces are indirect band gap. The adsorption of metals on GaAs nanowire surfaces are via chemisorption. Moreover, metal atom adsorption can enlarger the absorption coefficient of GaAs nanowires, which are gradually enhanced with increasing the coverage of metal atoms.

Polyoxometalate-like sub-nanometer molybdenum(vi)-oxo clusters for sensitive, selective and stable H2O2 sensing

Polyoxometalate-like sub-nanometer molybdenum(vi)-oxo clusters supported on mesoporous carbon are stably deposited on glassy carbon and screen-printed electrodes suitable for selective, sensitive and stable H₂O₂ sensing.

A self-powered delivery substrate boosts active enzyme delivery in response to human movements

Stimulated drug releases in response to human movements are highly appealing in medical therapy and various daily uses. However, the design of a mechanically responsive substrate that presents high delivery capacities and can also preserve the activities of sensitive molecules such as enzymes is still challenging. Taking advantage of the recent development in effective piezoelectric flexible films and in molecular delivery devices, we propose a composite delivery substrate that preserves enzyme activities and enhances molecular delivery in response to human movements such as finger presses or massages. The substrate is achieved by combining two parts, which are the energy converting unit and the molecular loading and releasing unit. The energy converting unit is a piezoelectric-dielectric flexible composite film that produces enhanced electricity and preserves the electricity longer compared to a pure piezoelectric polymer. The molecular delivery unit is a layer-by-layer multilayer containing mesoporous silica particles that are assembled at pH 9 but used in neutral solutions. The releases of molecules including small molecules, peptides, and proteins are all accelerated in response to finger presses irrespective of the signs or densities of their charges. More importantly, the enzyme CAT preserves its activity after release from the composite substrates, meaning that the CAT-loaded (PAH/MS)n(PAH/DAS)n@rGO-TFB/PVDF-HFP composite substrate holds promise as a self-powered soothing pad that effectively removes residue H2O2.

Amperometric hydrogen peroxide sensor using a glassy carbon electrode modified with a nanocomposite prepared from ferumoxytol and reduced graphene oxide decorated with platinum nanoparticles

A high-performance electrochemical H₂O₂ sensor was prepared by constructing multiple interfaces using platinum nanoparticles (Pt NPs), ferumoxytol (Fer) and reduced graphene oxide (rGO) on a glassy carbon electrode (GCE). The morphology of Fer/rGO and Fer/rGO-Pt was characterized by field emission scanning electron microscopy and energy-dispersive X-ray spectroscopy. Cyclic voltammetry and chronoamperometry were adopted to characterize the electrochemical properties of the sensor. Because of the synergistic catalytic effect of the compositions (rGO, Fer and Pt NPs) on the multiple interfaces, the sensor exhibits particularly high electrocatalytic activity toward the reduction of H₂O₂ with a low detection limit (~0.38 μM), a linear range (0.0004-0.01, 0.0075-4.3 and 4.9-10.8 mM), and a high sensitivity (340 μA mM^-1 cm^-2, n = 4) operated at a typical working voltage of +0.1 V (vs. Ag/AgCl). The electrode is selective and long-term stable. It was successfully applied to the determination of H₂O₂ in (spiked) milk samples. Graphical abstract Schematic presentation of an electrochemical H₂O₂ sensor using platinum nanoparticles (Pt NPs), ferumoxytol (Fer) and reduced graphene oxide (rGO) nanocomposites modified glassy carbon electrode (GCE). The sensor was applied to the determination of H₂O₂ in (spiked) milk samples.

Increased electrode activity during geosmin oxidation provided by Pt nanoparticle-embedded nanocarbon film

The musty odor compound geosmin was electrochemically detected by using Pt nanoparticle (PtNP)-embedded nanocarbon (Pt-C) films formed with unbalanced magnetron (UBM) co-sputtering. The sputtered Pt components formed NPs (typically 1.53-4.75 nm in diameter) spontaneously in the carbon films, owing to the poor intermiscibility of Pt with carbon. The surface concentrations of PtNPs embedded in the nanocarbon film were widely controllable (Pt = 4.8-35.9 at%) by regulating the target powers of the Pt and carbon individually. The obtained film had a flat surface (Ra = 0.17-0.18 nm) despite the fact the PtNPs were partially exposed at the surface. Compared with a Pt film electrode, some Pt-C films exhibited higher electrode activity against geosmin although the surface Pt concentrations of these Pt-C films were much lower than that of the Pt film electrode, thanks to the wider potential window and lower background current that resulted from the ultraflat and stable carbon-based film prepared by UBM co-sputtering. Computational experiments revealed that the theoretical oxidation potential (Eox) value for geosmin was relatively similar to that obtained in electrochemical experiments using our Pt-C film electrode. Moreover, we also theoretically estimated the possible oxidation site of geosmin molecules and the advantage of the NP shape of the electroactive Pt parts as regards the electrochemical oxidation of geosmin. We successfully used the Pt-C film (10.6 at%) electrode to detect geosmin in combination with HPLC at a low detection limit of 100 ng L-1.

Magnetic microspheres with polydopamine encapsulated ultra-small noble metal nanocrystals as mimetic enzymes for the colorimetric detection of H2O2 and glucose

A novel sandwich-structured magnetic microsphere with ultra-small noble metal nanocrystals as a mimetic enzyme for the colorimetric detection of H₂O₂ and glucose.

Au nanoparticle in situ decorated RGO nanocomposites for highly sensitive electrochemical genosensors

A novel hybrid nanocomposite formed by RGO flakes, surface functionalized by 1-pyrene carboxylic acid (PCA), densely and uniformly in situ decorated by Au NPs, is reported, for miRNA detection.

MoS2/Pt nanocomposite-functionalized microneedle for real-time monitoring of hydrogen peroxide release from living cells

This work describes the adaptive use of a conventional stainless steel acupuncture needle as the electrode substrate for construction of a molybdenum disulfide (MoS₂) and platinum nanoparticles (PtNPs) layer-modified microneedle sensor for real-time monitoring of hydrogen peroxide (H₂O₂) release from living cells. To construct the nanocomposite-functionalized microneedle, the needle surface was first coated with a gold film by ion sputtering to enhance the conductivity. Subsequently, an electrochemical deposition method was successfully employed to deposit MoS₂ nanosheet and Pt nanoparticles on the needle tip as the sensing interface. Electrochemical study demonstrated that the MoS₂/PtNPs nanocomposite-modified needle exhibited excellent catalytic performance and low over-potential toward the reduction of H₂O₂. Not only did the microneedle achieve a wide linear range from 1 to 100 μmol L^-1 with a limit of detection down to 0.686 μmol L^-1, but it also realized the highly specific detection of H₂O₂. Owing to these remarkable analytical advantages, the prepared microneedle was applied to determine H₂O₂ release from living cells with satisfactory results. The MoS₂/PtNPs nanocomposite-functionalized microneedle sensor is simple and affordable, and can serve as a promising electrochemical nonenzymatic sensing platform. Moreover, this superfine needle sensor shows great potential for real-time monitoring of reactive oxygen species in vivo with minimal damage.

Interfacial Engineering of Hierarchical Transition Metal Oxide Heterostructures for Highly Sensitive Sensing of Hydrogen Peroxide

Hydrogen peroxide (H₂ O₂ ) is a major messenger molecule in cellular signal transduction. Direct detection of H₂ O₂ in complex environments provides the capability to illuminate its various biological functions. With this in mind, a novel electrochemical approach is here proposed by integrating a series of CoO nanostructures on CuO backbone at electrode interfaces. High-resolution transmission electron microscopy (HRTEM), X-ray diffraction, and X-ray photoelectron spectroscopy demonstrate successful formation of core-shell CuO-CoO hetero-nanostructures. Theoretical calculations further confirm energy-favorable adsorption of H₂ O₂ on surface sites of CuO-CoO heterostructures. Contributing to the efficient electron transfer path and enhanced capture of H₂ O₂ in the unique leaf-like CuO-CoO hierarchical 3D interface, an optimal biosensor-based CuO-CoO-2.5 h electrode exhibits an ultrahigh sensitivity (6349 µA m m^-1 cm^-2 ), excellent selectivity, and a wide detection range for H₂ O₂ , and is capable of monitoring endogenous H₂ O₂ derived from human lung carcinoma cells A549. The synergistic effects for enhanced H₂ O₂ adsorption in integrated CuO-CoO nanostructures and performance of the sensor suggest a potential for exploring pathological and physiological roles of reactive oxygen species like H₂ O₂ in biological systems.

A comparison of nitrogen-doped sonoelectrochemical and chemical graphene nanosheets as hydrogen peroxide sensors

Nitrogen-doped graphene nanosheet (N-SEGN) with pyrrolic nitrogen and 5-9 vacancy defects has been successfully prepared from a hydrothermal reaction of tetra-2-pyridinylpyrazine and sonoelectrochemistry-exfoliated graphene nanosheet, with point defects. Additionally, based on the same reaction using chemically reduced graphene oxide, nitrogen-doped chemically reduced graphene oxide (N-rGO) with graphitic nitrogen was prepared. The N-SEGN and N-rGO were used as a non-enzymatic H₂O₂ sensors. The sensitivity of the N-SEGN was 231.3 μA·mM^-1·cm^-2, much greater than 57.3 μA·mM^-1·cm^-2 of N-rGO. The N-SEGN showed their potential for being a H₂O₂ sensor.

Non-enzymatic sensors based on a glassy carbon electrode modified with Au nanoparticles/polyaniline/SnO2 fibrous nanocomposites for nitrite sensing

A non-enzymatic sensor based on Au nanoparticles (AuNPs)/polyaniline (PANI)/tin oxide (SnO₂) nanocomposites (Au/PANI/SnO₂) was prepared for enhanced electrochemical sensing of nitrite (NO₂⁻).

A novel and simple cell-based electrochemical biosensor for evaluating the antioxidant capacity of Lactobacillus plantarum strains isolated from Chinese dry-cured ham

The analysis of antioxidants in foodstuffs has become an active area of research, leading to the recent development of numerous methods for assessing antioxidant capacity. Here we described the fabrication and validation of a novel and simple cell-based electrochemical biosensor for this purpose. The biosensor is used to assess the antioxidant capacity of cell-free extracts from Lactobacillus plantarum strains isolated from Chinese dry-cured ham. The biosensor relies on the determination of cellular reactive oxygen species (ROS) (the flux of H₂O₂ released from RAW 264.7 macrophage cells) to indirectly assess changes in intracellular oxidative stress level as influenced by L. plantarum strains. A one-step acidified manganese dioxide (a-MnO₂) modified gold electrode (GE) was used to immobilize RAW 264.7 macrophage cells, which were then encapsulated in a 3D cell culture system consisting of alginate/ graphene oxide (NaAlg/GO). The biosensor exhibited a rapid and sensitive response for the detection of H₂O₂ released from RAW264.7 cells. The detection limit was 0.02μM with a linear response from 0.05μM to 0.85μM and the biosensor was shown to have good stability and outstanding repeatability. This technique was then used for evaluating the antioxidant ability of extracts from L. plantarum NJAU-01. According to the electrochemical investigations and assays of SEM, TEM, and ROS, these cell-free extracts effectively reduced the oxidative stress levels in RAW264.7 cells under external stimulation. Extracts from L. plantarum strains at a dose of 10¹⁰CFU/mL showed the highest antioxidant activities with a relative antioxidant capacity (RAC) rate of 88.94%. Hence, this work provides a simple and efficient electrochemical biosensing platform based on RAW264.7 cells for fast, sensitive and quantitative assessment of antioxidant capacity of L. plantarum strains. The method demonstrates its potential for rapid screening for evaluating antioxidant properties of samples.

In-vivo electrochemical monitoring of H2O2 production induced by root-inoculated endophytic bacteria in Agave tequilana leaves

A dual-function platinum disc microelectrode sensor was used for in-situ monitoring of H₂O₂ produced in A. tequilana leaves after inoculation of their endophytic bacteria (Enterobacter cloacae). Voltammetric experiments were carried out from 0.0 to -1.0V, a potential range where H₂O₂ is electrochemically reduced. A needle was used to create a small cavity in the upper epidermis of A. tequilana leaves, where the fabricated electrochemical sensor was inserted by using a manual three-dimensional micropositioner. Control experiments were performed with untreated plants and the obtained electrochemical results clearly proved the formation of H₂O₂ in the leaves of plants 3h after the E. cloacae inoculation, according to a mechanism involving endogenous signaling pathways. In order to compare the sensitivity of the microelectrode sensor, the presence of H₂O₂ was detected in the root hairs by 3,3-diaminobenzidine (DAB) stain 72h after bacterial inoculation. In-situ pH measurements were also carried out with a gold disc microelectrode modified with a film of iridium oxide and lower pH values were found in A. tequilana leaves treated with bacteria, which may indicate the plant produces acidic substances by biosynthesis of secondary metabolites. This microsensor could be an advantageous tool for further studies on the understanding of the mechanism of H₂O₂ production during the plant-endophyte interaction.

Electrochemical hydrogen peroxide sensor based on carbon supported Cu@Pt core-shell nanoparticles

The Cu@Pt/C nanocomposites have been synthesized via two-step reduction method. Electrochemical observations showed that the Cu@Pt/C had better electrocatalytic activity for the reduction of hydrogen peroxide than Pt/C, with a wide linear range between 0.50μM and 32.56mM, a high sensitivity of 351.3μAmM^-1cm^-2, and a low detection limit of 0.15μM (signal/noise=3). Furthermore, the sensor based on Cu@Pt/C has potential applications due to its excellent long-time stability, good reproducibility and acceptable selectivity.

Optical Devices Constructed from Ferrocene-Modified Microgels for H2O2 Sensing

Ferrocene-modified poly(N-isopropylacrylamide)-based microgels were synthesized, characterized, and used to construct optical devices (etalons). The response of the microgels and etalons to H₂O₂ was investigated, and we show that both the microgel diameter and the optical properties of the etalons depend on the solution concentration of H₂O₂ from 0.6 to 35 mM. This behavior is a direct result of the oxidation of ferrocene, which influences the microgel diameter. This was also demonstrated by electrochemical-mediated oxidation/reduction of ferrocene using cyclic voltammetry. We go on to show that these materials could be used to monitor H₂O₂ that is generated from enzymatic reactions. Specifically, we show that the H₂O₂ generated from the oxidation of glucose catalyzed by glucose oxidase could be quantified. Finally, the devices can be reused multiple times via a regeneration process. This investigation illustrates the versatility of the etalon system to detect species of broad relevance and how they could potentially be used to quantify products of biological reactions.

Cobalt phosphide nanowires: an efficient electrocatalyst for enzymeless hydrogen peroxide detection

In this letter, we demonstrate for the first time that cobalt phosphide nanowires (CoP NWs) exhibit remarkable catalytic activity toward electrochemical detection of hydrogen peroxide (H2O2). As an enzymeless H2O2 sensor, such CoP NWs show a fast amperometric response within 5 s and a low detection limit of 0.48 μM. In addition, this nonenzymatic sensor displays good selectivity, long-term stability and excellent reproducibility.

pulSED: pulsed sonoelectrodeposition of fractal nanoplatinum for enhancing amperometric biosensor performance

A technique for deposition of fractal nanometal as a transducer in electrochemical sensing is described. The effect(s) of duty cycle and deposition time were explored, and two sensors are demonstrated.

Electrochemical flow injection analysis of hydrazine in an excess of an active pharmaceutical ingredient: achieving pharmaceutical detection limits electrochemically

The quantification of genotoxic impurities (GIs) such as hydrazine (HZ) is of critical importance in the pharmaceutical industry in order to uphold drug safety. HZ is a particularly intractable GI and its detection represents a significant technical challenge. Here, we present, for the first time, the use of electrochemical analysis to achieve the required detection limits by the pharmaceutical industry for the detection of HZ in the presence of a large excess of a common active pharmaceutical ingredient (API), acetaminophen (ACM) which itself is redox active, typical of many APIs. A flow injection analysis approach with electrochemical detection (FIA-EC) is utilized, in conjunction with a coplanar boron doped diamond (BDD) microband electrode, insulated in an insulating diamond platform for durability and integrated into a two piece flow cell. In order to separate the electrochemical signature for HZ such that it is not obscured by that of the ACM (present in excess), the BDD electrode is functionalized with Pt nanoparticles (NPs) to significantly shift the half wave potential for HZ oxidation to less positive potentials. Microstereolithography was used to fabricate flow cells with defined hydrodynamics which minimize dispersion of the analyte and optimize detection sensitivity. Importantly, the Pt NPs were shown to be stable under flow, and a limit of detection of 64.5 nM or 0.274 ppm for HZ with respect to the ACM, present in excess, was achieved. This represents the first electrochemical approach which surpasses the required detection limits set by the pharmaceutical industry for HZ detection in the presence of an API and paves the wave for online analysis and application to other GI and API systems.

Highly Sensitive Electrochemical Biosensor for Evaluation of Oxidative Stress Based on the Nanointerface of Graphene Nanocomposites Blended with Gold, Fe3O4, and Platinum Nanoparticles

High levels of H2O2 pertain to high oxidative stress and are associated with cancer, autoimmune, and neurodegenerative disease, and other related diseases. In this study, a sensitive H2O2 biosensor for evaluation of oxidative stress was fabricated on the basis of the reduced graphene oxide (RGO) nanocomposites decorated with Au, Fe3O4, and Pt nanoparticles (RGO/AuFe3O4/Pt) modified glassy carbon electrode (GCE) and used to detect the released H2O2 from cancer cells and assess the oxidative stress elicited from H2O2 in living cells. Electrochemical behavior of RGO/AuFe3O4/Pt nanocomposites exhibits excellent catalytic activity toward the relevant reduction with high selection and sensitivity, low overpotential of 0 V, low detection limit of ∼0.1 μM, large linear range from 0.5 μM to 11.5 mM, and outstanding reproducibility. The as-prepared biosensor was applied in the measurement of efflux of H2O2 from living cells including healthy normal cells and tumor cells under the external stimulation. The results display that this new nanocomposites-based biosensor is a promising candidate of nonenzymatic H2O2 sensor which has the possibility of application in clinical diagnostics to assess oxidative stress of different kinds of living cells.