2D and 3D graphene materials: Preparation and bioelectrochemical applications

Electrochemical and Plasmonic Detection of Myocardial Infarction Using Microfluidic Biochip Incorporated with Mesoporous Nanoscaffolds

This paper reports a microfluidic device for the electrochemical and plasmonic detection of cardiac myoglobin (cMb) and cardiac troponin I (cTnI) with noticeable limits of detection (LoD) as low as a few picograms per milliliter (pg/mL) ranges, achieved in a short detection time. The device features two working electrodes, each with a mesoporous Ni3V2O8 nanoscaffold grafted with reduced graphene oxide (rGO) that improves the interaction of diffusing analyte molecules with the sensing surface by providing a high surface area and reaction kinetics. Electrochemical studies reveal sensitivities as high as 9.68 μA ng/mL and a LoD of 2.0 pg/mL for cTnI, and 8.98 μA ng/mL and 4.7 pg/mL for cMb. Additionally, the surface plasmon resonance (SPR) studies demonstrate a low-level LoD of 8.8 pg/mL for cMb and 7.3 pg/mL for cTnI. The dual-modality sensor enables dynamic tracking of kinetic antigen-antibody interactions during sensing, self-verification through providing signals of two modes, and reduced false readout. This study demonstrates the complementary nature of the electrochemical and SPR modes in biosensing, with the electrochemical mode being highly sensitive and the SPR mode providing superior tracking of molecular recognition behaviors. The presented sensor represents a significant innovation in cardiovascular disease management and can be applied to monitor other clinically important biomolecules.

Easy cleaning plus stable activation of glassy carbon electrode surface by oxygen plasma

Glassy carbon (GC) electrodes are widely used in electroanalytical applications especially in bioelectrochemistry. Their use starts with an efficient surface cleaning and activation protocol, mostly based on surface polishing steps. We studied the use of an oxygen plasma exposure of GC electrodes to replace common polishing procedures. The cyclic voltammetry (CV) responses of ferrocyanide and ferrocene-dimethanol were used to compare brand new, surface-polished and plasma-treated GC electrodes. Plasma treatment induces CV responses with improved features, close to theoretical values, as compared to other methods. The plasma effects were quasi-stable over a week when electrodes were stored in water, this being explained by increased surface energy and hydrophilicity. Furthermore, when electroreduction of diazonium was performed on GC electrodes, the surface blockade could be removed by the plasma. Thus, a short oxygen plasma treatment is prone to replace polishing protocols, that display person-dependent efficiency, in most of the experiments with GC electrodes.

Graphene derivatives-based electrodes for the electrochemical determination of carbamate pesticides in food products: A review

Graphene (GR) composites have great potential for the determination of carbamates pesticides (CPs) by electrochemical methods. Since the beginning of the 20th century, GR has shown remarkable promise as electrode material for various sensors. The contamination of food products with harmful CPs is a major problem as they do not always damage human health immediately, but can be harmful after prolonged exposure. A range of advantages can be gained from their electrochemical determination, such as high sensitivity, reasonably selectivity, rapid detection, low limit of detection, and easy electrode fabrication. Furthermore, these electrochemical techniques are robust, reproducible, user-friendly, and conform to both "green" and "white" analytical chemistry. This review is focused on results published in the last ten years in the field of electrochemical determination of CPs in food products using GR and its derivatives.

Electrochemical Co-reduction of N2 and CO2 to Urea Using Bi2S3 Nanorods Anchored to N-Doped Reduced Graphene Oxide

Producing "green urea" using renewable energy, N₂, and CO₂ is a long-considered challenge. Herein, an electrocatalyst, Bi₂S₃/N-reduced graphene oxide (RGO), was synthesized by loading the Bi₂S₃ nanorods onto the N-RGO via a hydrothermal method. The Bi₂S₃/N-RGO composites exhibit the highest yield of urea (4.4 mmol g^-1 h^-1), which is 12.6 and 3.1 times higher than that of Bi₂S₃ (0.35 mmol g^-1 h^-1) and that of N-RGO (1.4 mmol g^-1 h^-1), respectively. N-RGO, because of its porous and open-layer structure, improves the mass transfer efficiency and stability, while the basic groups (-OH and -NH₂) promote the adsorption and activation of CO₂. Bi₂S₃ promotes the absorption and activation of inert N₂. Finally, the defect sites and the synergistic effect on the Bi₂S₃/N-RGO composites work simultaneously to form urea from N₂ and CO₂. This study provides new insights into urea synthesis under ambient conditions and a strategy for the design and development of a new material for green urea synthesis.

Controllable assembly of three-dimensional porous graphene-Au dual aerogels and its application for high-efficient bioelectrocatalytic O2 reduction

Aerogels derived from the colloidal nanoparticles featured with hierarchical interconnected pore-rich networks guarantee their great potentials in various applications. Herein, the controllable assembly of three-dimensional aerogels based on Au nanoparticles (Au NPs) and reduced graphene oxide (rGO) nanosheets as building blocks via a bottom-up approach have been systematically clarified. The difference of building blocks and their assembly sequence were crucially to the final aerogel morphologies and electrochemical properties. Specifically, the highly porous graphene-gold dual aerogels (rGO-Au DAGs) with interconnected rGO nanosheets and Au nanowires showed high conductivity, large surface area and good biocompatibility. Thus, it was employed as an excellent matrix to immobilize enzyme for high-efficient bioelectrocatalysis. Taking bilirubin oxidase as an example, a more positive on-set potential (0.60 V) and a larger catalytic current density (0.77 mA cm^-2@0.40 V) than those of other rGO-Au assemblies were achieved for direct bioelectrocatalytic O₂ reduction. This study will provide an efficient strategy for unique dual-structural aerogels design and shed light to develop new functional materials for bioelectrocatalytic applications such as biosensors and biofuel cells.

Anode modification of sediment microbial fuel cells (SMFC) towards bioremediating mariculture wastewater

Remediation of mariculture wastewater is of great practical importance. In this study, sediment microbial fuel cells (SMFCs) were adopted and carbon felt anodes were modified to enhance COD and ammonia removal in mariculture system. The results showed that the SMFC anode with 5 % (w/w) graphene oxide (GO) coating performed best in pollutants removal and electricity generation. The maximum power density approached 132 mW/m², nearly 4.5 times higher than the unmodified anode. The removal efficiency of COD and ammonia reached 82.1 % and 95.8 % respectively, both improved compared with the control and chemical modification. The modified anode effectively enriched the electrogenic Sulfurovum and Lactobacillus and thus led to a significant improvement in the electrochemical performance of SMFC. This study demonstrates the successful application of SMFCs with GO modified anodes in the in-situ removing pollutants and SMFCs present obvious remediation potential on the contaminated mariculture inhabitant.

Advances in analysis of pharmaceuticals by using graphene-based sensors

Safe and effective use of drugs relies on proper pharmaceutical analysis. Graphene has been extensively used to construct sensors for this purpose. Over the years, a large variety of pharmaceutical sensors have been developed from graphene or its derivatives. This articles reviews the current status of sensor development from graphene and its derivatives, and discusses the use of graphene-based sensors in pharmaceutical analysis. It is hoped that this article cannot only offer a snapshot of recent advances in the fabrication and use of graphene-based sensors, but can also provide insights into future engineering and optimization of the sensors for effective pharmaceutical analysis.

Recent Advances in Electrochemical Sensing of Hydrogen Peroxide (H2O2) Released from Cancer Cells

Cancer is by far the most common cause of death worldwide. There are more than 200 types of cancer known hitherto depending upon the origin and type. Early diagnosis of cancer provides better disease prognosis and the best chance for a cure. This fact prompts world-leading scientists and clinicians to develop techniques for the early detection of cancer. Thus, less morbidity and lower mortality rates are envisioned. The latest advancements in the diagnosis of cancer utilizing nanotechnology have manifested encouraging results. Cancerous cells are well known for their substantial amounts of hydrogen peroxide (H₂O₂). The common methods for the detection of H₂O₂ include colorimetry, titration, chromatography, spectrophotometry, fluorimetry, and chemiluminescence. These methods commonly lack selectivity, sensitivity, and reproducibility and have prolonged analytical time. New biosensors are reported to circumvent these obstacles. The production of detectable amounts of H₂O₂ by cancerous cells has promoted the use of bio- and electrochemical sensors because of their high sensitivity, selectivity, robustness, and miniaturized point-of-care cancer diagnostics. Thus, this review will emphasize the principles, analytical parameters, advantages, and disadvantages of the latest electrochemical biosensors in the detection of H₂O₂. It will provide a summary of the latest technological advancements of biosensors based on potentiometric, impedimetric, amperometric, and voltammetric H₂O₂ detection. Moreover, it will critically describe the classification of biosensors based on the material, nature, conjugation, and carbon-nanocomposite electrodes for rapid and effective detection of H₂O₂, which can be useful in the early detection of cancerous cells.

Construct α-FeOOH-Reduced Graphene Oxide Aerogel as a Carrier for Glucose Oxidase Electrode

A promising α-FeOOH-reduced graphene oxide aerogel (FeOOH-GA) has been prepared for the assembly of an enzyme electrode. The α-FeOOH-reduced graphene oxide aerogel was characterized by X-ray powder diffraction, field emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, Raman, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results reveal that graphene oxide is reduced by Fe²⁺ ion and α-FeOOH nanorods anchored on the reduced graphene oxide sheet through the Fe-O-C bond. Analyses using scanning electron microscopy and the Brunauer–Emmett–Teller method show that FeOOH-GA displays a various and interconnected pore structure. The FeOOH-GA was used as a support material on the glass carbon electrode (GCE) for glucose oxidase (GOD). Electrochemistry properties and bioelectrocatalytic activities of Nafion/GOD/FeOOH-GA/GCE were achieved from cyclic voltammetry and electrochemical impedance spectroscopy. The results show that Nafion/GOD/FeOOH-GA/GCE maintains outstanding catalytic activity and electrochemical properties. The FeOOH-GA could immobilize GOD through the hydrophobicity of the reduced graphene oxide and hydroxide radical of α-FeOOH. Appropriate α-FeOOH and diversified pore structure are beneficial for electron transfer, enzyme electrode storage, and interfacial electron transfer rate. All results indicated that the α-FeOOH-reduced graphene oxide aerogel as a carrier could effectively immobilize the tested enzyme.

Graphene Oxide and Biomolecules for the Production of Functional 3D Graphene-Based Materials

Graphene and its derivatives have been widely employed in the manufacturing of novel composite nanomaterials which find applications across the fields of physics, chemistry, engineering and medicine. There are many techniques and strategies employed for the production, functionalization, and assembly of graphene with other organic and inorganic components. These are characterized by advantages and disadvantages related to the nature of the specific components involved. Among many, biomolecules and biopolymers have been extensively studied and employed during the last decade as building blocks, leading to the realization of graphene-based biomaterials owning unique properties and functionalities. In particular, biomolecules like nucleic acids, proteins and enzymes, as well as viruses, are of particular interest due to their natural ability to self-assemble via non-covalent interactions forming extremely complex and dynamic functional structures. The capability of proteins and nucleic acids to bind specific targets with very high selectivity or the ability of enzymes to catalyse specific reactions, make these biomolecules the perfect candidates to be combined with graphenes, and in particular graphene oxide, to create novel 3D nanostructured functional biomaterials. Furthermore, besides the ease of interaction between graphene oxide and biomolecules, the latter can be produced in bulk, favouring the scalability of the resulting nanostructured composite materials. Moreover, due to the presence of biological components, graphene oxide-based biomaterials are more environmentally friendly and can be manufactured more sustainably compared to other graphene-based materials assembled with synthetic and inorganic components. This review aims to provide an overview of the state of the art of 3D graphene-based materials assembled using graphene oxide and biomolecules, for the fabrication of novel functional and scalable materials and devices.

Rapid detection of SARS-CoV-2 using graphene-based IoT integrated advanced electrochemical biosensor

Unique characteristics like large surface area, excellent conductivity, functionality, ease of fabrication, etc., of graphene and its derivatives, have been extensively studied as potential candidates in healthcare applications. They have been utilized as a potential nanomaterial in biosensor fabrication for commercialized point-of-care (POC) devices. This review concisely provided innovative graphene and its derivative-based-IoT (Internet-of-Things) integrated electrochemical biosensor for accurate and advanced high-throughput testing of SARS-CoV-2 in POC setting.

Thin-film nanocomposite NF membrane with GO on macroporous hollow fiber ceramic substrate for efficient heavy metals removal

The ceramic membrane has been widely used in the wastewater treatment based on the chemical resistance and superior separation performance. A robust and defect-free thin-film nanocomposite (TFN) nanofiltration (NF) membrane on the macroporous hollow fiber ceramic (HFC) substrate was novelly developed for heavy metals removal. Before interfacial polymerization (IP), the aqueous solution of graphene oxide (GO) grafted with ethylenediamine (EDA) was deposited on the HFC substrate by vacuum filtration. Then, a thin polyamide (PA) film was fabricated by EDA and 1,3,5-trimesoyl chloride (TMC), followed by heat treatment. The effects of GO content and EDA concentration on the performance of the NF membrane have been systematically investigated. The results showed that when the GO content was 0.015 mg·mL^-1 and the EDA concentration was 0.75 wt.%, the as-prepared eGO₃/PA-HFC membrane had a rejection rate of 94.12% for MgCl₂ and a pure water flux of 18.03 L·m^-2·h^-1. Additionally, the removal ability of eGO₃/PA-HFC membranes for heavy metal ions was satisfactory (93.33%, 92.73%, 90.45% and 88.35% for Zn²⁺, Cu²⁺, Ni²⁺ and Pb²⁺, respectively). The study explored further that it was efficient and stable for heavy metal ions removal during 30 h in the simulated tap water and mining wastewater, which indicated that the eGO/PA-HFC membrane has great application potential in wastewater treatment.

Molybdenum-containing polypyrrole self-supporting hollow flexible electrode for hydrogen peroxide detection in living cells

A flexible electrode based on polypyrrole-supported free-standing molybdenum oxide-molybdenum disulfide/polypyrrole nanostructure (MoO₃-MoS₂/PPy) was synthesized. The petal-like MoO₃-MoS₂ sheets grown on PPy were prepared step by step through simple electrodeposition and hydrothermal methods. The corresponding surface morphological and structural characterizations were characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The results showed that the prepared petal MoO₃-MoS₂ hybrid nanomaterials were uniformly distributed on the PPy skeleton and exhibited a three-dimensional porous network structure. The flexible electrode was used for non-enzymatic detection of hydrogen peroxide (H₂O₂), and the developed MoO₃-MoS₂/PPy nanomaterials exhibited high electrochemical sensing performance in the range of 0.3-150 μM, with the detection limit of 0.18 μM (S/N = 3). The excellent detection properties enabled the MoO₃-MoS₂/PPy flexible electrode to detect H₂O₂ released by living cells. The resulting MoO₃-MoS₂/PPy flexible electrode also has the advantages of customizable shape and adjustability, which provides a potential platform for constructing clinically diagnosed in vivo portable instruments and real-time environmental monitoring.

Building with graphene oxide: effect of graphite nature and oxidation methods on the graphene assembly

During nearly 2 centuries of history in graphene researches, numerous researches were reported to synthesize graphene oxide (GO) and build a proper graphene assembly. However, tons of research prevail without verifying the reproducibility of GO that can be sensitively attributed by the graphite nature, and chemical processes. Here, the structure and chemistry of GO products were analyzed by considering parent graphite sources, and three different oxidation methods based on Hummer's method and the addition of H3PO4. The oxidation level of GO was characterized by monitoring the C/O and sp2 carbon ratio from X-ray photoelectroscopy (XPS) spectra. It was observed that the oxidant intercalation behavior was dependent on the morphological differences of graphite; synthetic and natural flake graphite were compared based on their origins in shape and size from different suppliers. Thermal reduction and exfoliation were applied to GO powders to prepare thermally expanded graphene oxide (TEGO) as a graphene assembly. Gas releases from the reduction of oxygen functional groups split layered GO structure and build a porous structure that varied specific surface area regarding oxidation degrees of GO.

Rational design of electroactive redox enzyme nanocapsules for high-performance biosensors and enzymatic biofuel cell

The potential application of biodevices based on enzymatic bioelectrocatalysis are limited by poor stability and electrochemical performance. To solve the limitation, modifying enzyme with functional polymer to tailor enzyme function is highly desirable. Herein, glucose oxidase (GOx) was chosen as a model enzyme, and according to the chemical structure of GOx cofactor (flavin adenine dinucleotide, FAD), we customize a biomimetic cofactor containing vinyl group (SFAD) for GOx, and prepared an GOx nanocapsule via in-situ polymerization. The characterization of particle size distribution, TEM, fluorescence and electrochemical performance indicated the successful formation of electroactive GOx nanocapsule with SFAD-containing polymeric network (n (GOx-SFAD-PAM)). The network can act as an electronic "highway" to link the active site with electrode, with capability to accelerate electron transfer as well as enhanced GOx stability. Further investigation of bioelectrocatalysis shows that n (GOx-SFAD-PAM)-based biosensor has low detection potential (-0.4 vs. Ag/AgCl), high sensitivity (64.97 μAmM^-1cm^-2), good anti-interference performance, quick response (3⁓5s) and excellent stability, and that n (GOx-SFAD-PAM)-based enzymatic biofuel cell (EBFC) has the high maximum power density (1011.21 μWcm^-2), which is a 385-fold increase over that of native GOx-based EBFC (2.62 μWcm^-2). This study suggests that novel enzyme nanocapsule with electroactive polymeric shell might provide a prospective solution for the performance improvement of enzymatic bioelectrocatalysis-based biodevices.

Advancements in Microfabricated Gas Sensors and Microanalytical Tools for the Sensitive and Selective Detection of Odors

In recent years, advancements in micromachining techniques and nanomaterials have enabled the fabrication of highly sensitive devices for the detection of odorous species. Recent efforts done in the miniaturization of gas sensors have contributed to obtain increasingly compact and portable devices. Besides, the implementation of new nanomaterials in the active layer of these devices is helping to optimize their performance and increase their sensitivity close to humans' olfactory system. Nonetheless, a common concern of general-purpose gas sensors is their lack of selectivity towards multiple analytes. In recent years, advancements in microfabrication techniques and microfluidics have contributed to create new microanalytical tools, which represent a very good alternative to conventional analytical devices and sensor-array systems for the selective detection of odors. Hence, this paper presents a general overview of the recent advancements in microfabricated gas sensors and microanalytical devices for the sensitive and selective detection of volatile organic compounds (VOCs). The working principle of these devices, design requirements, implementation techniques, and the key parameters to optimize their performance are evaluated in this paper. The authors of this work intend to show the potential of combining both solutions in the creation of highly compact, low-cost, and easy-to-deploy platforms for odor monitoring.

A Brief Description of Cyclic Voltammetry Transducer-Based Non-Enzymatic Glucose Biosensor Using Synthesized Graphene Electrodes

The essential disadvantages of conventional glucose enzymatic biosensors such as high fabrication cost, poor stability of enzymes, pH value-dependent, and dedicated limitations, have been increasing the attraction of non-enzymatic glucose sensors research. Beneficially, patients with diabetes could use this type of sensor as a fourth-generation of glucose sensors with a very low cost and high performance. We demonstrate the most common acceptable transducer for a non-enzymatic glucose biosensor with a brief description of how it works. The review describes the utilization of graphene and its composites as new materials for high-performance non-enzymatic glucose biosensors. The electrochemical properties of graphene and the electrochemical characterization using the cyclic voltammetry (CV) technique of electrocatalysis electrodes towards glucose oxidation have been summarized. A recent synthesis method of the graphene-based electrodes for non-enzymatic glucose sensors have been introduced along with this study. Finally, the electrochemical properties such as linearity, sensitivity, and the limit of detection (LOD) for each sensor are introduced with a comparison with each other to figure out their strengths and weaknesses.

Alendronate loaded graphene oxide functionalized collagen sponge for the dual effects of osteogenesis and anti-osteoclastogenesis in osteoporotic rats

Graphene Oxide (GO)-related hydrogels have been extensively studied in hard tissue repair, because GO can not only enhance the mechanical properties of polymers but also promote osteogenic differentiation of mesenchymal stem cells. However, simple GO-related hydrogels are not ideal for the repair of osteoporotic bone defects as the overactive osteoclasts in osteoporosis. Alendronate (Aln) is known to inhibit osteoclasts and may bind to GO through covalent connection. Therefore, delivering Aln in GO-related hydrogels may be effective to repair osteoporotic bone defects. Here, we developed a control-released system which is constructed by collagen (Col)-GO sponges loaded with Aln (Col-GO-Aln) for osteoporotic bone defect repair. In vitro, Col-GO-Aln sponges prolonged the release period of Aln, and the sponge containing 0.05% (w/v) GO released Aln faster than sponge with 0.2% GO. Furthermore, tartrate-resistant acid phosphatase (TRAP) and F-actin staining demonstrated that Col-GO-Aln sponges effectively inhibited osteoclastogenesis of monocyte-macrophages. In vivo, micro-CT scan showed that the volume of newborn bone in defect site by 0.05% GO sponge was nearly three times larger than that of other groups. Moreover, the CT and histological examinations of rat femur proved that Col-GO-Aln sponges decreased the number of osteoclasts and suppressed the systemic bone loss in osteoporotic rats. These findings reveal that the application of GO as carriers of anti-osteoporosis drugs is a viable treatment for osteoporosis. The results also underscore the potential of GO-related hydrogels with Aln-releasing capacity for bone regeneration in osteoporosis.

•

Alendronate-loading graphene oxide modified collagen sponge (Col-GO-Aln) exhibit a sustained drug delivery.

•

Col-GO-Aln sponge showed active anti-osteoclastogenesis and osteogenesis ability in vitro and in situ repair.

•

Col-GO-Aln sponge achieved a potential systemic resistance to bone loss in osteoporotic rats.

Direct Fabrication of Ultra-Sensitive Humidity Sensor Based on Hair-Like Laser-Induced Graphene Patterns

Three-dimensional (3-D) porous graphitic structures have great potential for sensing applications due to their conductive carbon networks and large surface area. In this work, we present a method for facile fabrication of hair-like laser induced graphene (LIG) patterns using a laser scribing system equipped with a 355 nm pulsed laser. The polyimide (PI) film was positioned on a defocused plane and irradiated at a slow scanning speed using a misaligned laser beam. These patterns have the advantages of a large surface area and abundant oxidation groups. We have applied the hair-like LIG patterns to a humidity sensor. The humidity sensor showed good sensitivity characteristics and a large amount of electronic carriers can be stored.

Function of c-type cytochromes of Shewanella xiamenensis in enhanced anaerobic bioreduction of Cr(VI) by graphene oxide and graphene oxide/polyvinyl alcohol films

Graphene-based materials have been demonstrated to facilitate electron extracellular transfer (EET) of Shewanella. In this study, compared to group lacking graphene oxide (GO)-based materials, GO films-added group and graphene oxide/polyvinyl alcohol (GO/PVA) film-added group delivered 2.67- and 3.13-fold increases in the Cr(VI) reduction by Shewanella xiamenensis, respectively. The whole reduction process could be divided into three stages, including microbial Cr(VI) reduction and GO reduction stage, microbial GO reduction stage and microbial Cr(VI) reduction mediated by reduced graphene oxide (rGO) stage. Moreover, gene analysis revealed that addition of GO and GO/PVA films stimulated overexpression of several c-type cytochrome (c-Cyts) genes, including mtrA, mtrB, mtrC, mtrD, mtrE, mtrF, omcA, petC and SO-4047. Specifically, appreciable Cr(VI) reduction by the strains that overexpressed mtrA, mtrB, mtrC, mtrD, mtrE, mtrF and omcA further confirmed that overexpression of c-Cyts genes indeed enhanced the efficiency of Cr(VI) reduction. Based on these results, the specific function of every c-Cyt was clearly found in Cr(VI) reduction by the induction of GO-based materials. Our finding has disclosed a synergetic mechanism stimulated by GO-based materials to enhance Cr(VI) bioreduction that was not only mediated through the modification of material but also upregulated the expression of functional genes.

Dual Engineering Interface-Driven Complementary Graphene Oxide-Protein Dimer Supramolecular Architecture Enables Nucleus Imaging and Therapy

Seeking a versatile nanoplatform for multimodal nucleus imaging and therapy is a challenging task. General complementary bottom-up bionanotechnology for controlling a 3D supramolecular coassembly is proposed. The dual engineering interface proof-of-concept of the supramolecular architecture can be demonstrated via a genetically engineered protein dimer and plasmonically engineered graphene oxide (GO). Incorporation of anisotropic plasmonic nanoparticles as an intercalation layer among the GO 3D supramolecular architecture can provide covalent conjugation sites and simultaneously endow tunable optical properties of GO, ranging from the ultraviolet-to-near-infrared region. Interestingly, the precise design of a specific two-site mutation of the plasmid is favorable for giving an organized coassembly instead of random networks of GO, which contributes to giving continuous distinguishable enhanced Raman imaging for tracking cancer cells. Unexpectedly, penetration into the cell nucleus via the submicro 3D supramolecular coassembly exhibits an excellent nucleus therapeutic potential of cancer cells.

Applications of three-dimensional graphenes for preconcentration, extraction, and sorption of chemical species: a review

This review (with 115 refs) summarizes applications of 3-dimensional graphene (3DGs) and its derivatives in the fields of preconcentration, extraction, and sorption. Following an introduction into the field (including a definition of the materials treated here), the properties and synthetic strategies for 3DGs are described. The next section covers applications of 3DG-based adsorbents in solid phase extraction of organic species including drugs, phthalate esters, chlorophenols, aflatoxins, insecticides, and pesticides. Another section treats applications of 3DGs in solid phase microextraction of species such as polycyclic aromatic hydrocarbons, alcohols, and pesticides. We also describe how the efficiency of assays may be improved by using these materials as a sorbent. A final section covers conclusions and perspectives. Graphical abstract Graphical abstract contains poor quality and small text inside the artwork. Please do not re-use the file that we have rejected or attempt to increase its resolution and re-save. It is originally poor, therefore, increasing the resolution will not solve the quality problem. We suggest that you provide us the original format. We prefer replacement figures containing vector/editable objects rather than embedded images. Preferred file formats are eps, ai, tiff and pdf.Tiff file of graphical abstract was attached. Schematic presentation of synthesis of three-dimensional graphene (3DG) from two-dimensional graphene (2DG) with self-assembly, template-assisted and direct deposition methods. Application of 3DG-based nanoadsorbents in direct immersion-solid phase microextraction (DI-SPME), headspace-SPME (HS-SPME), magnetic-solid phase extraction (Magnetic-SPE), dispersive-SPE, and magnetic sheet-SPE.

Biomarkers-based Biosensing and Bioimaging with Graphene for Cancer Diagnosis

At the onset of cancer, specific biomarkers get elevated or modified in body fluids or tissues. Early diagnosis of these biomarkers can greatly improve the survival rate or facilitate effective treatment with different modalities. Potential nanomaterial-based biosensing and bioimaging are the main techniques in nanodiagnostics because of their ultra-high selectivity and sensitivity. Emerging graphene, including two dimensional (2D) graphene films, three dimensional (3D) graphene architectures and graphene hybrids (GHs) nanostructures, are attracting increasing interests in the field of biosensing and bioimaging. Due to their remarkable optical, electronic, and thermal properties; chemical and mechanical stability; large surface area; and good biocompatibility, graphene-based nanomaterials are applicable alternatives as versatile platforms to detect biomarkers at the early stage of cancer. Moreover, currently, extensive applications of graphene-based biosensing and bioimaging has resulted in promising prospects in cancer diagnosis. We also hope this review will provide critical insights to inspire more exciting researches to address the current remaining problems in this field.

Polystyrene as Graphene Film and 3D Graphene Sponge Precursor

Polystyrene as a thin film on arbitrary substrates or pellets form defective graphene/graphitic films or powders that can be dispersed in water and organic solvents. The materials were characterized by visible absorption, Raman and X-ray photoelectron spectroscopy, electron and atomic force microscopy, and electrochemistry. Raman spectra of these materials showed the presence of the expected 2D, G, and D peaks at 2750, 1590, and 1350 cm⁻¹, respectively. The relative intensity of the G versus the D peak was taken as a quantitative indicator of the density of defects in the G layer.

A review on graphene-based nanocomposites for electrochemical and fluorescent biosensors

Biosensors with high sensitivity, selectivity and a low limit of detection, reaching nano/picomolar concentrations of biomolecules, are important to the medical sciences and healthcare industry for evaluating physiological and metabolic parameters.

Three-Dimensional Graphene Foams: Synthesis, Properties, Biocompatibility, Biodegradability, and Applications in Tissue Engineering

Presently, clinical nanomedicine and nanobiotechnology have impressively demanded the generation of new organic/inorganic analogues of graphene (as one of the intriguing biomedical research targets) for stem-cell-based tissue engineering. Among different shapes of graphene, three-dimensional (3D) graphene foams (GFs) are highly promising candidates to provide conditions for mimicking in vivo environments, affording effective cell attachment, proliferation,and differentiation due to their unique properties. These include the highest biocompatibility among nanostructures, high surface-to-volume ratio, 3D porous structure (to provide a homogeneous/isotropic growth of tissues), highly favorable mechanical characteristics, and rapid mass and electron transport kinetics (which are required for chemical/physical stimulation of differentiated cells). This review aims to describe recent and rapid advances in the fabrication of 3D GFs, together with their use in tissue engineering and regenerative nanomedicine applications. Moreover, we have summarized a broad range of recent studies about the behaviors, biocompatibility/toxicity,and biodegradability of these materials, both in vitro and in vivo. Finally, the highlights and challenges of these 3D porous structures, compared to the current polymeric scaffold competitors, are discussed.

Three-dimensional graphene-based polymer nanocomposites: preparation, properties and applications

Motivated by the unique structure and outstanding properties of graphene, three-dimensional (3D) graphene-based polymer nanocomposites (3D-GPNCs) are considered as new generation materials for various multi-functional applications. This review presents an overview of the preparation, properties and applications of 3D-GPNCs. Three main approaches for fabricating 3D-GPNCs, namely 3D graphene based template, polymer particle/foam template, and organic molecule cross-linked graphene, are introduced. A thorough investigation and comparison of the mechanical, electrical and thermal properties of 3D-GPNCs are performed and discussed to understand their structure-property relationship. Various potential applications of 3D-GPNCs, including energy storage and conversion, electromagnetic interference shielding, oil/water separation, and sensors, are reviewed. Finally, the current challenges and outlook of these emerging 3D-GPNC materials are also discussed.

Gold nanorod embedded novel 3D graphene nanocomposite for selective bio-capture in rapid detection of Mycobacterium tuberculosis

Tuberculosis (TB) is a chronic and infectious airborne disease which requires a diagnosing system with high sensitivity and specificity. However, the traditional gold standard method for TB detection remains unreliable with low specificity and sensitivity. Nanostructured composite materials coupled with impedimetric sensing utilised in this study offered a feasible solution. Herein, novel gold (Au) nanorods were synthesized on 3D graphene grown by chemical vapour deposition. The irregularly spaced and rippled morphology of 3D graphene provided a path for Au nanoparticles to self-assemble and form rod-like structures on the surface of the 3D graphene. The formation of Au nanorods were showcased through scanning electron microscopy which revealed the evolution of Au nanoparticle into Au islets. Eventually, it formed nanorods possessing lengths of ~ 150 nm and diameters of ~ 30 nm. The X-ray diffractogram displayed appropriate peaks suitable to defect-free and high crystalline graphene with face centered cubic Au. The strong optical interrelation between Au nanorod and 3D graphene was elucidated by Raman spectroscopy analysis. Furthermore, the anchored Au nanorods on 3D graphene nanocomposite enables feasible bio-capturing on the exposed Au surface on defect free graphene. The impedimetric sensing of DNA sequence from TB on 3D graphene/Au nanocomposite revealed a remarkable wide detection linear range from 10 fM to 0.1 µM, displays the capability of detecting femtomolar DNA concentration. Overall, the novel 3D graphene/Au nanocomposite demonstrated here offers high-performance bio-sensing and opens a new avenue for TB detection.

A mechanism study on toxicity of graphene oxide to Daphnia magna: Direct link between bioaccumulation and oxidative stress

Graphene oxide (GO) possesses versatile applicability and high hydrophilicity, thus may have frequent contact with aquatic organisms. However, the ecological risks of GO in aquatic ecosystems remain largely unexplored currently. This study evaluated the comprehensive toxicological effects of GO on Daphnia magna, a key species in fresh water ecosystem. The results revealed nonsevere acute toxicities, including immobility (72 h EC₅₀: 44.3 mg/L) and mortality (72 h LC₅₀: 45.4 mg/L), of GO on D. magna. To understand the underlying mechanism of GO exposure, changes in superoxide dismutase (SOD) and lipid peroxidation (LPO) of D. magna exposed to GO were correlated, which revealed elevated GO-mediated oxidative stress and damages, especially in the long-time and high-dose exposure groups. The observations of in vivo fluorescence labeled with 2', 7'-dichlorofluorescin further demonstrated that reactive oxygen species were concentrated in daphnia guts, which corresponded with the high bioaccumulation level (5 mg/L, 24 h body burden: 107.9 g/kg) of GO in daphnia guts. However, depuration of GO from daphnia was not difficult. Daphnia almost released all GO within 24 h after it was transferred to clean water. These results hence suggest that GO could accumulate and induce significant oxidative stress in the gut of D. magna, while D. daphnia can also relieve the acute toxicity by depurating GO.

CeO2-x/C/rGO nanocomposites derived from Ce-MOF and graphene oxide as a robust platform for highly sensitive uric acid detection

Developing suitable substrate materials is of significance in constructing electrochemical biosensors for fast and reliable quantification of molecules of chemical and biomedical interest. For practical applications, biosensors working at low negative potentials have the advantage of high selectivity and sensitivity. In this work, CeO_2-x/C/rGO nanocomposites have been synthesized through the pyrolysis of metal organic frameworks with graphene oxide. The CeO_2-x/C/rGO nanocomposites exhibit excellent catalytic properties towards H₂O₂, which is one of the uricase catalyzed intermediates at low working potentials due to the coexistence of Ce³⁺ and reduced graphene oxide (rGO). A novel biosensor based on the CeO_2-x/C/rGO nanocomposites has been developed and utilized for the detection of uric acid, an important molecule in the biological and medical fields. The biosensor based on the CeO_2-x/C/rGO nanocomposites presents a high sensitivity of 284.5 μA cm^-2 mM^-1 at -0.4 V (vs. SCE), a wide linear range between 49.8 and 1050.0 μM and a low detection limit of 2.0 μM. Moreover, it is found that the amperometric responses are free from interference of ascorbic acid and urea, which shows a great potential for practical applications.

Hierarchically porous graphene for batteries and supercapacitors

Hierarchical porous graphene based materials are explored for their application as electrochemical storage devices due to their large specific surface area, high electrical and thermal conductivity, and excellent specific capacity.

Magnetic Nanoparticle-Reduced Graphene Oxide Nanocomposite as a Novel Bioelectrode for Mediatorless-Membraneless Glucose Enzymatic Biofuel Cells

In this work, an enzymatic biofuel cell (EBC) based on a membraneless and mediatorless glucose enzymatic fuel cell system was constructed for operation in physiological conditions (pH 7.0 and temperature 37 °C). The new platform EBC made of nanocomposite, including magnetic nanoparticles (Fe₃O₄ NPs) and reduced graphene oxide (RGO), was used for the immobilization of glucose oxidase (GOD) as bioanode and bilirubin oxidase (BOD) as biocathode. The EBC bioelectrodes were fabricated without binder or adhesive agents for immobilized enzyme and the first EBC using superparamagnetic properties with Fe₃O₄ NPs has been reported. The performance of the EBC was evaluated with promising results. In EBC tests, the maximum power density of the EBC was 73.7 μW cm⁻² and an open circuit voltage (OCV) as +0.63 V with 5 mM of glucose concentration for the physiological condition of humans. The Fe₃O₄-RGO nanocomposite offers remarkable enhancement in large surface areas, is a favorable environment for enzyme immobilization, and facilitates electron transfer between enzymes and electrode surfaces. Fe₃O₄ and RGO have been implied as new promising composite nanomaterials for immobilizing enzymes and efficient platforms due to their superparamagnetism properties. Thus, glucose EBCs could potentially be used as self-powered biosensors or electric power sources for biomedical device applications.

Freestanding and flexible graphene papers as bioelectrochemical cathode for selective and efficient CO2 conversion

During microbial electrosynthesis (MES) driven CO₂ reduction, cathode plays a vital role by donating electrons to microbe. Here, we exploited the advantage of reduced graphene oxide (RGO) paper as novel cathode material to enhance electron transfer between the cathode and microbe, which in turn facilitated CO₂ reduction. The acetate production rate of Sporomusa ovata-driven MES reactors was 168.5 ± 22.4 mmol m⁻² d⁻¹ with RGO paper cathodes poised at −690 mV versus standard hydrogen electrode. This rate was approximately 8 fold faster than for carbon paper electrodes of the same dimension. The current density with RGO paper cathodes of 2580 ± 540 mA m⁻² was increased 7 fold compared to carbon paper cathodes. This also corresponded to a better cathodic current response on their cyclic voltammetric curves. The coulombic efficiency for the electrons conversion into acetate was 90.7 ± 9.3% with RGO paper cathodes and 83.8 ± 4.2% with carbon paper cathodes, respectively. Furthermore, more intensive cell attachment was observed on RGO paper electrodes than on carbon paper electrodes with confocal laser scanning microscopy and scanning electron microscopy. These results highlight the potential of RGO paper as a promising cathode for MES from CO₂.

N+ implantation induce cytocompatibility of shape-controlled three-dimensional self-assembly graphene

AIM

The aim of the present research was to synthesize N⁺ implanted 3D self-assembly graphene (N⁺/3D-SGHs) to overcome the weaknesses of graphene (small sizes and poor hydrophilicity) in tissue engineering scaffolds.

MATERIALS & METHODS

N⁺/3D-SGHs was achieved by ion implantation on one-step hydrothermal synthesized 3D self-assembly graphene (3D-SGHs), and N⁺/3D-SGHs with different doses of nitrogen ions (1 × 10¹⁶ ions/cm², 1 × 10¹⁸ ions/cm² and 1 × 10²⁰ ions/cm²), which adjusted by nitrogen ion beam intensity.

RESULTS

N⁺/3D-SGHs, as scaffolds, provide stereo space and hydrophilic groups for mouse-fibroblast cells (L929) growth and proliferation. Notably, N⁺/3D-SGHs with the N⁺ injected quantity of 1 × 10²⁰ ions/cm² displayed the highest protein-adhesion strength, cell viability and proliferation, which supported its good cytocompatibility.

CONCLUSION

This study demonstrated N⁺/3D-SGHs as a promising and effective tissue scaffold that might have applications in biomedicine.