InGaN/GaN nanowires as a new platform for photoelectrochemical sensors - detection of NADH

Quantum Dot/TiO2 Nanocomposite-Based Photoelectrochemical Sensor for Enhanced H2O2 Detection Applied for Cell Monitoring and Visualization

This work exploits the possibility of using CdSe/ZnS quantum dot (QD)-electrodes to monitor the metabolism of living cells based on photoelectrochemical (PEC) measurements. To realize that, the PEC setup is improved with respect to an enhanced photocurrent signal, better stability, and an increased signal-to-noise ratio, but also for a better biocompatibility of the sensor surface on which cells have been grown. To achieve this, a QD-TiO2 heterojunction is introduced with the help of atomic layer deposition (ALD). The heterojunction reduces the charge carrier recombination inside the semiconductor nanoparticles and improves the drift behavior. The PEC performance is carefully analyzed by adjusting the TiO2 thickness and combining this strategy with multilayer immobilizations of QDs. The optimal thickness of this coating is ≈5 nm; here, photocurrent generation can be enhanced significantly (e.g., for a single QD layer electrode by more than one order of magnitude at 0 V vs Ag/AgCl). The resulting optimized electrode is used for hydrogen peroxide (H2O2) sensing with a good sensitivity down to µmolar concentrations, reusability, stability, response rate, and repeatability. Finally, the sensing system is applied to monitor the activity of cells directly grown on top of the electrode surface.

Atomic-Scale Characterization of Planar Selective-Area-Grown InAs/InGaAs Nanowires

Atomic-scale information about the structural and compositional properties of novel semiconductor nanowires is essential to tailoring their properties for specific applications, but characterization at this length scale remains a challenging task. Here, quasi-1D InAs/InGaAs semiconductor nanowire arrays were grown by selective area epitaxy (SAE) using molecular beam epitaxy (MBE), and their subsequent properties were analyzed by a combination of atom probe tomography (APT) and aberration-corrected transmission electron microscopy (TEM). Results revealed the chemical composition of the outermost thin InAs layer, a fine variation in the indium content at the InAs/InGaAs interface, and lightly incorporated element tracing. The results highlight the importance of correlative microscopy approaches in revealing complex nanoscale structures, with TEM being uniquely suited to interrogating the crystallography of InGaAs NWs, whereas APT is capable of three-dimensional (3D) elemental mapping, revealing the subtle compositional variation near the boundary region. This work demonstrates a detailed pathway for the nanoscale structural assessment of novel one-dimensional (1D) nanomaterials.

Tailoring of the photocatalytic activity of CeO2 nanoparticles by the presence of plasmonic Ag nanoparticles

The present study investigates basic features of a photoelectrochemical system based on CeO₂ nanoparticles fixed on gold electrodes. Since photocurrent generation is limited to the absorption range of the CeO₂ in the UV range, the combination with metal nanoparticles has been studied. It can be shown that the combination of silver nanoparticles with the CeO₂ can shift the excitation range into the visible light wavelength range. Here a close contact between both components has been found to be essential and thus, hybrid CeO₂@Ag nanoparticles have been prepared and analyzed. We have collected arguments that electron transfer occurs between both compositional elements of the hybrid nanoparticles.The photocurrent generation can be rationalized on the basis of an energy diagram underlying the necessity of surface plasmon excitation in the metal nanoparticles, which is also supported by wavelength-dependent photocurrent measurements. However, electrochemical reactions seem to occur at the CeO₂ surface and consequently, the catalytic properties of this material can be exploited as exemplified with the photoelectrochemical reduction of hydrogen peroxide. It can be further demonstrated that the layer-by layer technique can be exploited to create a multilayer system on top of a gold electrode which allows the adjustment of the sensitivity of the photoelectrochemical system. Thus, with a 5-layer electrode with hybrid CeO₂@Ag nanoparticles submicromolar hydrogen peroxide concentrations can be detected.

Detection of aflatoxin B1 with a new label-free fluorescence aptasensor based on PVP-coated single-walled carbon nanohorns and SYBR Gold

This paper describes a novel fluorescence label-free aptasensor to detect aflatoxin B₁ (AFB₁) by utilizing SYBR Gold, aptamer, and single-walled carbon nanohorns (SWCNHs). In the presence of AFB₁, the conformation of AFB₁-specific aptamer went through and the spatial structure of this specific aptamer was transformed accordingly. Due to the resistance of the transformed aptamer when adsorbed on the surface of SWCNHs, the protection of the fluorescence of SYBR Gold was accomplished. Consequently, concentrations of AFB₁ showed a strong association with fluorescence intensity. The detection limit (LOD) of AFB₁ was 1.89 ng/mL, while the linear range was 5-200 ng/mL and fluorescence intensity satisfactorily correlated (R² = 0.9919) with the logarithm of AFB₁ concentration.

Homogeneous and well-aligned GaN nanowire arrays via a modified HVPE process and their cathodoluminescence properties

In this work, we demonstrate the growth of homogeneous and well-aligned [0001]-oriented 1-D GaN nanoarrays via a modified hydride vapor phase epitaxy (HVPE) process using GaCl₃ and NH₃ as precursors. The density and length of the grown nanowires can be easily controlled by the process parameters. It was found that the growth technique provides Cl-rich growth conditions, which lead to special morphology and optical properties of the GaN nanoarrays. Different from reported GaN nanowires, the as-synthesized GaN nanoarrays in this study exhibit a hollow bamboo-like structure. Also, the cathodoluminescence spectrum shows strong visible luminescence between 400 and 600 nm wavelengths centered at 450 nm, and the disappearance of an intrinsic emission peak, which has been investigated in detail with the assistance of first-principles calculations. The strategy proposed in this work will pave a solid way for the controlled nucleation and growth of well-aligned GaN nanowire arrays which are significant for applications in large-scale integrated optoelectronic nanodevices, functionalized sensors and photoelectrocatalysis.

Photoelectrochemical assay based on CdS nanocrystal\hexagonal carbon-nitrogen tube nanocomposite for detection of silver ions

A photochemical assay was reported based on CdS nanocrystal (NC)\hexagonal carbon-nitrogen tube (HCNT) nanocomposite for the detection of Ag⁺. When CdS NCs were combined with HCNT, the photocurrent intensity was increased extensively. After incubation of Ag⁺ with CdS NC\HCNT nanocomposite-modified electrode, Ag₂S was formed on the electrode by the ion-change reaction. As the band gap of Ag₂S cannot match well with HCNT, the photogenerated electron-hole pairs cannot separate efficiently, so the photocurrent intensity decreases. A good linear relationship between the concentration of Ag⁺ in the range from 0.01 to 3 μM and the corresponding photocurrent intensity was obtained with a detection limit of 3.3 nM (S/N = 3). The assay was employed to detect Ag⁺ in lake water and human serum with satisfactory results, which indicated that it might have a broad application in different areas. Photoelectrochemical assay was reported based on CdS nanocrystal\hexagonal carbon-nitrogen tube nanocomposite for detection of Ag^.

Introducing visible-light sensitivity into photocatalytic CeO2 nanoparticles by hybrid particle preparation exploiting plasmonic properties of gold: enhanced photoelectrocatalysis exemplified for hydrogen peroxide sensing

In this report we combine the catalytic properties of CeO₂ nanoparticles with their transduction ability for photoelectrochemical sensing. This study highlights the usage of CeO₂ providing catalytic activity towards H₂O₂, but only with a limited excitation range in the UV for the construction of a sensing system. In order to improve the photoelectrocatalysis of CeO₂ nanoparticles by extending their excitation to visible light, Au/CeO₂ core/shell hybrid nanoparticles have been synthesized. The hybrid nanoparticles are fixed on electrodes, allowing for the generation of photocurrents, the direction of which can be controlled by the electrode potential (without bias). The application of the hybrid nanoparticles results in an enhanced photocurrent amplitude under white light illumination as compared to the pure CeO₂ nanoparticles. Wavelength-dependent measurements confirm the participation of the Au core in the signal transduction. This can be explained by improved charge carrier generation within the hybrid particles. Thus, by using a plasmonic element the photoelectochemical response of a catalytic nanoparticle (i.e. CeO₂) has been spectrally extended. The effect can be exploited for sensorial hydrogen peroxide detection. Here higher photocatalytic current responses have been found for the hybrid particles fixed to gold electrodes although the catalytic reduction has been comparable for both types of nanoparticles. Thus, it can be demonstrated that Au/CeO₂ core-shell nanoparticles allow the utilization of visible light for photoelectrochemical hydrogen peroxide (H₂O₂) detection with improved sensitivity under white light illumination or application of such particles with only visible light excitation, which is not possible for pure CeO₂. With help of the layer-by-layer (LbL) technique for nanoparticle immobilization, the electrode response can be adjusted and with a 5 layers electrode a low detection limit of about 3 μM H₂O₂ with a linear detection range up to 2000 μM is obtained.

Metal Nanocomposites Based Electrochemical Sensor Platform for few Emerging Biomarkers

:

Design of high-performance electrochemical sensor and biosensor platforms has attracted much devotion for the sensitive and selective detection of emergent biomarkers. Electrochemical sensor offers numerous advantageous features include cost-effective and ease of miniaturization, rapid and online monitoring, simultaneous detection ability, etc., which have captivated the potential interdisciplinary research. In this review, the advances and challenges towards the electrochemical detection of emergent biomarkers such as hydrogen peroxide, nitric oxide, β-nicotinamide adenine acetaminophen, dinucleotide (NADH) in biofluids are highlighted based on the recent research outcomes. In fact, the effective utility and benefits of transition metal nanocomposites without the utilization of biological materials, including enzymes, antibodies, etc. as electrode materials towards the detection of selected biomarkers in practical biofluids, monitoring early-stage and diagnosis of disease related biomarkers, are also described. These promising metal nanomaterials based electrochemical sensor platforms concrete the tactic for a new generation of sensing devices.

Enhancement of Biosensors by Implementing Photoelectrochemical Processes

Research on biosensors is growing in relevance, taking benefit from groundbreaking knowledge that allows for new biosensing strategies. Electrochemical biosensors can benefit from research on semiconducting materials for energy applications. This research seeks the optimization of the semiconductor-electrode interfaces including light-harvesting materials, among other improvements. Once that knowledge is acquired, it can be implemented with biological recognition elements, which are able to transfer a chemical signal to the photoelectrochemical system, yielding photo-biosensors. This has been a matter of research as it allows both a superior suppression of background electrochemical signals and the switching ON and OFF upon illumination. Effective electrode-semiconductor interfaces and their coupling with biorecognition units are reviewed in this work.

Light-controlled imaging of biocatalytic reactions via scanning photoelectrochemical microscopy for multiplexed sensing

A light-controlled multiplexing platform has been developed on the basis of a quantum dot-sensitized inverse opal TiO₂ electrode with integrated biocatalytic reactions. Spatially resolved illumination enables multiplexed sensing and imaging of enzymatic oxidation reactions at relatively negative applied potentials.

Contact engineering of single core/shell SiC/SiO2 nanowire memory unit with high current tolerance using focused femtosecond laser irradiation

Single nanowire memory units are of particular interest in the design of high-density nanoelectronic circuits, but the performance due to weak contact state remains a major problem. In this paper, bonding between core/shell SiC/SiO2 nanowire and Au electrodes can be improved via local contact engineering with femtosecond (fs) laser irradiation. An optimized heterojunction (Au-SiO2-SiC) is possible since plasmonic enhanced optical absorption can be localized at the metal-oxide (Au-SiO2) interface. Electron transport across the barrier and charge accumulation at the oxide-semiconductor (SiO2-SiC) interface are improved in nanowire circuits. A fast and stable resistance change can be achieved after only one biasing cycle ('write') and the written state can be read/extracted at a low voltage (∼ 0.5 V). Unlike other as-built nanowire circuits, the resistance state can be retained for 10 min in the absence of external power, indicating that these devices can be used for short-term memory units. High current tolerance is also provided in the circuit by the surface oxide shell which acts to protect the inner SiC core. The current density carried by the single SiC/SiO2 nanowire circuit can be as high as ∼3 × 106 A cm-2 before break down, and that breakdown occurs as a two-stage process.

Iron phosphorus trichalcogenide ultrathin nanosheets: enhanced photoelectrochemical activity under visible-light irradiation

Exploiting novel visible-light sensitive materials for the photoelectrochemical (PEC) technique is deeply meaningful for energy conversion and analytic detection. Owing to the tunable bandgap structure and strong absorption of visible light, the rising-star two-dimensional (2D) metal phosphorus trichalcogenide (MPX₃) nanomaterials are expected to be promising photochemical sensitizers toward PEC biosensors. Moreover, guided by DFT calculations, the FePS₃ nanosheets possessed a narrower bandgap than the bulk form, thereby enabling high availability of visible-light absorption for the FePS₃ nanosheets. In this work, 2D FePS₃ nanosheets were successfully synthesized by a facile salt-templated method. By tuning the proportion of the salt template, the thickness of the FePS₃ nanosheets could be manipulated. As a result, the FePS₃ nanosheets exhibited an obviously enhanced photoelectrochemical behavior with visible light and sensitive detection towards glucose. Being the first experimental report regarding the MPS₃ nanosheets toward PEC activity, our finding can be an essential stepping stone in the pursuit of the further exploration of other 2D materials for the PEC technology.

InGaN as a Substrate for AC Photoelectrochemical Imaging

AC photoelectrochemical imaging at electrolyte–semiconductor interfaces provides spatially resolved information such as surface potentials, ion concentrations and electrical impedance. In this work, thin films of InGaN/GaN were used successfully for AC photoelectrochemical imaging, and experimentally shown to generate a considerable photocurrent under illumination with a 405 nm modulated diode laser at comparatively high frequencies and low applied DC potentials, making this a promising substrate for bioimaging applications. Linear sweep voltammetry showed negligible dark currents. The imaging capabilities of the sensor substrate were demonstrated with a model system and showed a lateral resolution of 7 microns.

A boronic acid carbon nanodots/poly(thionine) sensing platform for the accurate and reliable detection of NADH

In this work, a novel electrochemical sensing platform was designed and fabricated by the modification of boronic acid functionalized carbon nanodots (B-CNDs) and poly(thionine) (pTHI) on an electrode surface. B-CNDs can not only accelerate electron transfer but also covalently interact with cis-diol groups of dihydronicotinamide adenine dinucleotide (NADH) through functionalized boronic acid groups. Meanwhile, pTHI served as an inner reference element to provide a built-in correction, which enabled the sensor to detect NADH with high accuracy and reliability based on a ratiometric signal (∆I_NADH/∆I_THI). The electrochemical experimental results demonstrated that the ratiometric strategy-based sensor possessed good selectivity and high sensitivity. A linear range of 5.0 × 10^-7 - 2.0 × 10^-4 mol/L for NADH detection was obtained with a limit of detection of 1.5 × 10^-7 mol/L. The sensor has been applied to analyze NADH in human serum samples with satisfactory results. The simple and effective ratiometric strategy reported here can be further used to prepare electrochemical sensors for selective, sensitive, and reliable detection of other cis-diol compounds.

Multiplexed Readout of Enzymatic Reactions by Means of Laterally Resolved Illumination of Quantum Dot Electrodes

Triggering electrochemical reactions with light provides a powerful tool for the control of complex reaction schemes on photoactive electrodes. Here, we report on the light-directed, multiplexed detection of enzymatic substrates using a nonstructured gold electrode modified with CdSe/ZnS quantum dots (QDs) and two enzymes, glucose oxidase (GOx) and sarcosine oxidase (SOx). While QDs introduce visible-light sensitivity into the electrode architecture, GOx and SOx allow for a selective conversion of glucose and sarcosine, respectively. For the QD immobilization to the gold electrode, a linker-assisted approach using trans-4,4'-stilbenedithiol has been used, resulting in the generation of a photocurrent. Subsequently, GOx and SOx have been immobilized in spatially separated spots onto the QD electrode. For the local readout of the QD electrode, a new measurement setup has been developed by moving a laser pointer across the surface to defined positions on the chip surface. The amplitudes of the photocurrents upon illumination of the GOx or SOx spot depend in a concentration-dependent manner on the presence of glucose and sarcosine, respectively. This measurement also allows for a selective detection in the presence of other substances. The setup demonstrates the feasibility of multiplexed measurements of enzymatic reactions using a focused light pointer, resulting in an illumination area with a diameter of 0.3 mm for analyzing spots of different enzymes. Moving the laser pointer in the x- and y-direction and simultaneously detecting the local photocurrent also allow a spatial imaging of enzyme immobilization. Here, not only the spot dimensions but also the activity of the enzyme can be verified.

Direct imaging of Indium-rich triangular nanoprisms self-organized formed at the edges of InGaN/GaN core-shell nanorods

Higher indium incorporation in self-organized triangular nanoprisms at the edges of InGaN/GaN core-shell nanorods is directly evidenced by spectral cathodoluminescence microscopy in a scanning transmission electron microscope. The nanoprisms are terminated by three 46 nm wide a-plane nanofacets with sharp interfaces forming a well-defined equilateral triangular base in the basal plane. Redshifted InGaN luminescence and brighter Z-contrast are resolved for these structures compared to the InGaN layers on the nanorod sidewalls, which is attributed to at least 4 % higher indium content. Detailed analysis of the inner optical and structural properties reveals luminescence contributions from 417 nm up to 500 nm peak wavelength proving the increasing indium concentration inside the nanoprism towards the nanorod surface.

Photovoltage-triggered electrochromic tablet for visualized photoelectrochemical sensing

In this work, we designed an integrated photoelectrochemical (PEC) analytical system with photovoltage-regulated electrochromic tablet for visualized sensing. The electrochromic tablet consisted of electron-injector (EI) part and colorimetric system, which was functionalized with dye-sensitized titanium dioxide and nickel oxide nanosheet film as the recognition element and signal readout, respectively. Under irradiation of home-built white light, the EI part provided sufficient and stable photovoltage and injected the photoexcited electrons to nickel oxide nanosheet through the conductive inner side of indium tin oxide slide. Thus, the different color states of nickel oxide nanosheet were observed, resulting in a detectable signal by naked eyes for visual analysis. More importantly, the color change was identified to be dependent on the photovoltages generated from EI part. Using copper ions as a model analyte, the electrochromic tablet was successfully applied to visually detect copper ions based on its quenching effect on photovoltage due to the formation of exciton trapping. As a result, the copper ions could be simultaneously determined over a wide range through photovoltage record, average RGB value, and naked eyes. Furthermore, the device exhibited considerable stability and could be reused through simple washing steps. The smart tablet PEC system provides a new avenue to design practical PEC sensor in point-of-care diagnosis.

PVP-coated gold nanoparticles for the selective determination of ochratoxin A via quenching fluorescence of the free aptamer

This paper describes an aptamer/gold nanoparticle-based assay for ochratoxin A (OTA) detection. This assay is based on the use of an aptamer labeled with carboxyfluorescein (FAM) at its 5'-end and gold nanoparticles (AuNPs) that act as quenchers of fluorescence. When OTA is absent in the system, the fluorescently labeled aptamers are adsorbed on the surface of AuNPs. The fluorescence signal of the fluorescein-labeled OTA aptamer generated is quenched by the fluorescence resonance energy transfer effect of AuNPs. When OTA is present in the system, the fluorescently labeled aptamer binds to OTA and forms a folded structure, which can resist the adsorption of AuNPs. Thus, the fluorescent signal can be retained. The detection limit of this sensing platform is 5 nM, and the linear detection range is 10-1000 nM (R2 = 0.994). The procedure was validated by the quantitation of OTA in spiked ginger powder samples and were found to be free of interference by the sample matrix. The recoveries and the relative standard deviation varied from 89.0% to 117.8% and from 1.9% to 6.3%, respectively.

Integration of Enzymes in Polyaniline-Sensitized 3D Inverse Opal TiO2 Architectures for Light-Driven Biocatalysis and Light-to-Current Conversion

Inspired by natural photosynthesis, coupling of artificial light-sensitive entities with biocatalysts in a biohybrid format can result in advanced photobioelectronic systems. Herein, we report on the integration of sulfonated polyanilines (PMSA1) and PQQ-dependent glucose dehydrogenase (PQQ-GDH) into inverse opal TiO₂ (IO-TiO₂) electrodes. While PMSA1 introduces sensitivity for visible light into the biohybrid architecture and ensures the efficient wiring between the IO-TiO₂ electrode and the biocatalytic entity, PQQ-GDH provides the catalytic activity for the glucose oxidation and therefore feeds the light-driven reaction with electrons for an enhanced light-to-current conversion. Here, the IO-TiO₂ electrodes with pores of around 650 nm provide a suitable interface and morphology needed for the stable and functional assembly of polymer and enzyme. The IO-TiO₂ electrodes have been prepared by a template approach applying spin coating, allowing an easy scalability of the electrode height and surface area. The successful integration of the polymer and the enzyme is confirmed by the generation of an anodic photocurrent, showing an enhanced magnitude with increasing glucose concentrations. Compared to flat and nanostructured TiO₂ electrodes, the three-layered IO-TiO₂ electrodes give access to a 24-fold and 29-fold higher glucose-dependent photocurrent due to the higher polymer and enzyme loading in IO films. The three-dimensional IO-TiO₂|PMSA1|PQQ-GDH architecture reaches maximum photocurrent densities of 44.7 ± 6.5 μA cm^-2 at low potentials in the presence of glucose (for a three TiO₂ layer arrangement). The onset potential for the light-driven substrate oxidation is found to be at -0.315 V vs Ag/AgCl (1 M KCl) under illumination with 100 mW cm^-2, which is more negative than the redox potential of the enzyme. The results demonstrate the advantageous properties of IO-TiO₂|PMSA1|PQQ-GDH biohybrid architectures for the light-driven glucose conversion with improved performance.

CsPbBr3 perovskite quantum dots/ZnO inverse opal electrodes: photoelectrochemical sensing for dihydronicotinamide adenine dinucleotide under visible irradiation

All-inorganic perovskite quantum dots (PQDs) have attracted tremendous attention due to their extraordinary optical properties, especially CsPbBr₃ QDs with their high stability and photoluminescence efficiency.