A reusable ratiometric electrochemical biosensor on the basis of the binding of methylene blue to DNA with alternating AT base sequence for sensitive detection of adenosine

A novel ratiometric electrochemical sensing platform combined with molecularly imprinted polymer and Fe-MOF-NH2/CNTs-NH2/MXene composite for efficient detection of ofloxacin

BACKGROUND

Ofloxacin (OFL) is often abused in medicine and animal husbandry, which poses a great threat to human health and ecological environment. Therefore, it is necessary to establish efficient method to detect OFL. Electrochemical sensor has attracted widespread attention due to the advantages of low cost and fast response. However, most electrochemical sensors usually use one response signal to detect the target, which makes it sensitive to the variable background noise in the complex environment, resulting in low robustness and selectivity. The ratio detection mode and employing molecularly imprinted polymer (MIP) are two strategies to solve these problems.

RESULTS

A novel molecular imprinting polymer-ratiometric electrochemical sensor (MIP-RECS) based on Fe-MOF-NH2/CNTs-NH2/MXene composite was prepared for the rapid and sensitive detection of OFL. The positively charged Fe-MOF-NH2 and CNTs-NH2 as interlayer spacers were introduced into the negatively charged MXene through a simple electrostatic self-assembly technique, which effectively prevented the agglomeration of MXene and increased the electrocatalytic activity. A glass carbon electrode was modified by the composite and a MIP film was electropolymerized on it using o-phenylenediamine and β-cyclodextrin as bifunctional monomers and OFL as template. Then a MIP-RECS was designed by adding dopamine (DA) into the electrolyte solution as internal reference, and OFL was quantified by the response current ratio of OFL to DA. The current ratio and the concentration of OFL displayed a satisfying linear relationship in the range of 0.1 μM-100 μM, with a limit of detection (LOD) of 13.2 nM.

SIGNIFICANCE

Combining molecular imprinting strategy and ratio strategy, the MIP-RECS has impressive selectivity compared with the non-imprinted polymer-RECS, and has better repeatability and reproducibility than non-ratiometric sensor. The MIP-RECS has high sensitivity and accuracy, which was applied for the detection of OFL in four different brands of milk and was verified by HPLC method with satisfactory results.

Boronate crosslinking-based ratiometric electrochemical assay of glycated albumin

As a product of nonenzymatic glycation, glycated albumin (GA) is a promising serum marker for the short-term glycemic monitoring in patients with diabetes. On the basis of the boronate crosslinking (BCL)-enabled direct labeling of ferrocene (Fc) tags to the nonenzymatically glycated (NEG) sites, we report herein a novel aptamer-based ratiometric electrochemical (apt-REC) platform for the point-of-care (POC) assay of GA. This apt-REC platform is based on the recognition of GA proteins by the methylene blue (MB)-modified aptamer receptors and the labeling of the Fc tags to the NEG sites via the BCL. Using MB as the reference tag and Fc as the quantification tag, the ratio of the oxidation currents (i.e., IFc/IMB) can serve as the yardstick for the ratiometric assay of GA. Due to the presence of tens of the NEG sites, each GA protein can be labeled with tens of quantification tags, permitting the amplified assay in a simple, time-saving, and low-cost manner. The ratiometric signal exhibited a good linear response over the range from 0.1 to 100 μg/mL, with a detection limit of 45.5 ng/mL. In addition to the superior reproducibility and robustness, this apt-REC platform is highly selective (capable of discriminating GA against human serum albumin (HSA)) and applicable to GA assay in serum samples. Due to its low cost, high reproducibility and robustness, simple operation, and high sensitivity and selectivity, this apt-REC platform holds great promise in the POC assay of GA for diabetes management.

Electrostatic Nanocage-Confined Probe for Electrochemical Detection of CA19-9 in Human Serum

Prompt and accurate detection of CA19-9 in human serum has great clinical significance for the early diagnosis and disease monitoring of cancer. Herein, we develop a convenient and antifouling electrochemical sensor for CA19-9 determination by immobilization of both an electrochemical redox probe [methylene blue (MB)] and immunorecognition element (CA19-9 antibody) on an electrostatic nanocage consisting of bipolar silica nanochannel array (bp-SNA). bp-SNA is composed of a negatively charged inner layer (n-SNA) and positively charged outer layer (p-SNA), which could be stably prepared on indium tin oxide (ITO) in several seconds using a two-step electrochemically assisted self-assembly approach and display asymmetric surface charges for confinement and enrichment of cationic MB into the inner n-SNA layer through electrostatic interaction. Modification of the CA19-9 antibody on the top surface of bp-SNA confers the sensing interface with specific recognition capacity. An antibody-antigen complex formed at the as-prepared immunosensor causes the decreased electrochemical signals of MB, achieving sensitive determination of CA19-9 with a wider linear dynamic range from 10 μU/mL to 50 U/mL and a low detection limit (3 μU/mL). Furthermore, accurate and feasible analysis of the CA19-9 amount in human serum samples by our proposed probe-integrated electrochemical immunosensor is realized.

Target-Induced Electrochemical Sensor Based on Foldable Aptamer and MoS2@MWCNTs-PEI for Enhanced Detection of AFB1 in Peanuts

Herein, a sensitive and selective electrochemical sensor based on aptamer folding was constructed to detect aflatoxin B1 (AFB1) in peanuts. Specifically, polyethylenimine-functionalized multiwalled carbon nanotubes modified with molybdenum disulfide (MoS2@MWCNTs-PEI) were used as the electrode matrix to enable a large specific surface area, which were characterized by the Randles-Sevcik equation. Additionally, AuNPs were used to immobilize the aptamer via the Au-S covalent bond and provide a favorable microenvironment for signal enhancement. Methylene blue (MB) was modified at the proximal 3' termini of the aptamer as the capture probe, while the signal transduction of the sensor was obtained through changes in conformation and position of MB induced by the binding between AFB1 and the probe. Changes in spatial conformation could be recorded by electrochemical methods more readily. This electrochemical aptasensor demonstrated remarkable sensitivity to AFB1 with an extensive detection range (1 pg/mL to 100 ng/mL) and a lower limit detection (1.0 × 10-3 ng/mL). Moreover, using the constructed aptasensor, AFB1 was identified successfully in peanut samples, with recoveries ranging from 95.83 to 107.53%, illustrating its potential use in determining AFB1 in food.

In-Situ Integration of 3D C-MEMS Microelectrodes with Bipolar Exfoliated Graphene for Label-Free Electrochemical Cancer Biomarkers Aptasensor

The electrochemical label-free aptamer-based biosensors (also known as aptasensors) are highly suitable for point-of-care applications. The well-established C-MEMS (carbon microelectromechanical systems) platforms have distinguishing features which are highly suitable for biosensing applications such as low background noise, high capacitance, high stability when exposed to different physical/chemical treatments, biocompatibility, and good electrical conductivity. This study investigates the integration of bipolar exfoliated (BPE) reduced graphene oxide (rGO) with 3D C-MEMS microelectrodes for developing PDGF-BB (platelet-derived growth factor-BB) label-free aptasensors. A simple setup has been used for exfoliation, reduction, and deposition of rGO on the 3D C-MEMS microelectrodes based on the principle of bipolar electrochemistry of graphite in deionized water. The electrochemical bipolar exfoliation of rGO resolves the drawbacks of commonly applied methods for synthesis and deposition of rGO, such as requiring complicated and costly processes, excessive use of harsh chemicals, and complex subsequent deposition procedures. The PDGF-BB affinity aptamers were covalently immobilized by binding amino-tag terminated aptamers and rGO surfaces. The turn-off sensing strategy was implemented by measuring the areal capacitance from CV plots. The aptasensor showed a wide linear range of 1 pM-10 nM, high sensitivity of 3.09 mF cm-2 Logc-1 (unit of c, pM), and a low detection limit of 0.75 pM. This study demonstrated the successful and novel in-situ deposition of BPE-rGO on 3D C-MEMS microelectrodes. Considering the BPE technique's simplicity and efficiency, along with the high potential of C-MEMS technology, this novel procedure is highly promising for developing high-performance graphene-based viable lab-on-chip and point-of-care cancer diagnosis technologies.

Electrochemistry/Photoelectrochemistry-Based Immunosensing and Aptasensing of Carcinoembryonic Antigen

Recently, electrochemistry- and photoelectrochemistry-based biosensors have been regarded as powerful tools for trace monitoring of carcinoembryonic antigen (CEA) due to the fact of their intrinsic advantages (e.g., high sensitivity, excellent selectivity, small background, and low cost), which play an important role in early cancer screening and diagnosis and benefit people's increasing demands for medical and health services. Thus, this mini-review will introduce the current trends in electrochemical and photoelectrochemical biosensors for CEA assay and classify them into two main categories according to the interactions between target and biorecognition elements: immunosensors and aptasensors. Some recent illustrative examples are summarized for interested readers, accompanied by simple descriptions of the related signaling strategies, advanced materials, and detection modes. Finally, the development prospects and challenges of future electrochemical and photoelectrochemical biosensors are considered.

Nucleic acid-based electrochemical biosensor: Recent advances in probe immobilization and signal amplification strategies

With the increasing importance of accurate and early disease diagnosis and the development of personalized medicine, DNA-based electrochemical biosensor has attracted broad scientific and clinical interests in the past decades due to its unique hybridization specificity, fast response time, and potential for miniaturization. In order to achieve high detection sensitivity, the design of DNA electrochemical biosensors depends critically on the improvement of the accessibility of target molecules and the enhancement of signal readout. Here, we summarize the recent advances in DNA probe immobilization and signal amplification strategies with a special focus on DNA nanostructure-supported DNA probe immobilization method, which provides the opportunity to rationally control the distance between probes and keep them in upright confirmation, as well as the contribution of functional nanomaterials in enhancing the signal amplification. The next challenge of biosensors will be the fabrication of point-of-care devices for clinical testing. The advancement of multidisciplinary areas, including nanofabrication, material science, and biochemistry, has exhibited profound promise in achieving such portable sensing devices. This article is categorized under: Diagnostic Tools > Biosensing Diagnostic Tools > Diagnostic Nanodevices Biology-Inspired Nanomaterials > Nucleic Acid-Based Structures.

A Methylene Blue Assisted Electrochemical Sensor for Determination of Drug Resistance of Escherichia coli

Due to the abuse of antibiotics in clinical, animal husbandry, and aquaculture, drug-resistant pathogens are produced, which poses a great threat to human and the public health. At present, a rapid and effective drug sensitivity test method is urgently needed to effectively control the spread of drug-resistant bacteria. Using methylene blue as a redox probe, the electrochemical signals of methylene blue in drug-resistant Escherichia coli strains were analyzed by a CV method. Graphene ink has been used for enhancing the electrochemical signal. Compared with the results of the traditional drug sensitivity test, we proposed a rapid electrochemical drug sensitivity test method which can effectively identify the drug sensitivity of Escherichia coli. The sensitivity of four E. coli isolates to ciprofloxacin, gentamicin, and ampicillin was tested by an electrochemical drug sensitivity test. The respiratory activity value %RA was used as an indicator of bacterial resistance by electrochemical method.

A novel ratiometric electrochemical biosensing strategy based on T7 exonuclease-assisted homogenous target recycling coupling hairpin assembly-triggered double-signal output for the multiple amplified detection of miRNA

A novel ratiometric electrochemical biosensing strategy based on T7 exonuclease (T7 Exo)-assisted homogenous target recycling coupling hairpin assembly triggered dual-signal output was proposed for the accurate and sensitive detection of microRNA-141 (miRNA-141). Concretely, in the presence of target miRNA, abundant signal transduction probes were released via the T7 Exo-assisted homogenous target recycling amplification, which could be captured by the specially designed ferrocene-labeled hairpin probe (Fc-H1) on -electrode interface and triggered the nonenzymatic catalytic hairpin assembly (Fc-H1 + MB-H2) to realize the cascade signal amplification and dual-signal output. Through such a conformational change process, the electrochemical signal of Fc (IFc) and MB (IMB) is proportionally and substantially decreased and increased. Therefore, the signal ratio of IMB/IFc can be employed to accurately reflect the true level of original miRNA. Benefiting from the efficient integration of the T7 Exo-assisted target recycle, nonenzymatic hairpin assembly and dual-signal output mode, the proposed sensor could realize the amplified detection of miRNA-141 effectively with a wide detection range from 1 fM to 100 pM, and a detection limit of 200 aM. Furthermore, it exhibits outstanding sequence specificity to discriminate mismatched RNA, acceptable reproducibility and feasibility for real sample. This strategy effectively integrated the advantages of multiple amplification and ratiometric output modes, which could provide an accurate and efficient method in biosensing and clinical diagnosis.

Ratiometric Electrochemistry: Improving the Robustness, Reproducibility and Reliability of Biosensors

Electrochemical biosensors are an increasingly attractive option for the development of a novel analyte detection method, especially when integration within a point-of-use device is the overall objective. In this context, accuracy and sensitivity are not compromised when working with opaque samples as the electrical readout signal can be directly read by a device without the need for any signal transduction. However, electrochemical detection can be susceptible to substantial signal drift and increased signal error. This is most apparent when analysing complex mixtures and when using small, single-use, screen-printed electrodes. Over recent years, analytical scientists have taken inspiration from self-referencing ratiometric fluorescence methods to counteract these problems and have begun to develop ratiometric electrochemical protocols to improve sensor accuracy and reliability. This review will provide coverage of key developments in ratiometric electrochemical (bio)sensors, highlighting innovative assay design, and the experiments performed that challenge assay robustness and reliability.

Facile construction of ratiometric electrochemical immunosensor using hierarchical PtCoIr nanowires and porous SiO2@Ag nanoparticles for accurate detection of septicemia biomarker

Procalcitonin (PCT) is a sensitive and specific biomarker for sepsis diagnosis. In this study, a novel ratio-typed electrochemical immunosensor was constructed for reliable and sensitive assay of PCT based on hierarchical PtCoIr nanowires/polyethylene polyamine-grafted-ferrocene (PtCoIr HNWs/PEPA-Fc) and porous SiO₂@Ag nanoparticles-toluidine blue (porous SiO₂@Ag NPs-TB). Importantly, the PtCoIr HNWs/PEPA-Fc was first modified on the sensing interface, which harvested stable and strong electrochemical signals for readout of Fc due to the enriched anchoring sites created by the PtCoIr HNWs. Meanwhile, porous SiO₂@Ag NPs-TB behaved as the label to conjugate with secondary antibody (Ab₂), which also provided another strong detection signals originated from TB confined in such porous structures. The resulting immunosensor displayed a measurable output of procalcitonin (PCT) in the dynamic scope of 0.001 ~ 100 ng mL^-1 with a low limit of detection (LOD) of 0.46 pg mL^-1 (S/N = 3). Moreover, we exploited this strategy for PCT assay in a diluted human serum sample with acceptable results, exhibiting promising applications in the clinical analysis.

Application of electrochemical methods for the detection of abiotic stress biomarkers in plants

Abiotic stress is the main cause of low productivity in plants. Therefore, it is important to detect stress and respond to it in a timely manner to avoid irreversible damage to plant productivity and health. The application of traditional methods in agriculture is limited by expensive equipment and cumbersome sample processing. More effective detection methods are urgently needed due to the trace amounts and low stabilities of plant biomarkers. Electrochemical detection methods have the unique advantages of high accuracy, a low detection limit, fast response and easy integration with systems. In this review, the application of three types of electrochemical methods to phytohormone assessment is highlighted including direct electrochemical, immunoelectrochemical, and photoelectrochemical methods. Research on electrochemical methods for detecting abiotic stress biomarkers, including various phytohormones, is also summarized with examples. To date, the detection limit of exogenous plant hormones can reach pg/mL or even lower. Nevertheless, more efforts need to be made to develop a portable instrument for in situ online detection if electrochemical sensors are to be applied to the detection of the endogenous hormones or the physiological state of plants. Additionally, plant-wearable sensors that can be directly attached to or implanted into plants for continuous, noninvasive and real-time monitoring are emphasized. Finally, rational summaries of the considered methods and present challenges and future prospects in the field of abiotic stress detection-based electrochemical biosensors are thoroughly discussed.

Recent Advances in Aptamer Sensors

Recently, aptamers have attracted attention in the biosensing field as signal recognition elements because of their high binding affinity toward specific targets such as proteins, cells, small molecules, and even metal ions, antibodies for which are difficult to obtain. Aptamers are single oligonucleotides generated by in vitro selection mechanisms via the systematic evolution of ligand exponential enrichment (SELEX) process. In addition to their high binding affinity, aptamers can be easily functionalized and engineered, providing several signaling modes such as colorimetric, fluorometric, and electrochemical, in what are known as aptasensors. In this review, recent advances in aptasensors as powerful biosensor probes that could be used in different fields, including environmental monitoring, clinical diagnosis, and drug monitoring, are described. Advances in aptamer-based colorimetric, fluorometric, and electrochemical aptasensing with their advantages and disadvantages are summarized and critically discussed. Additionally, future prospects are pointed out to facilitate the development of aptasensor technology for different targets.

Highly sensitive label-free electrochemical aptasensors based on photoresist derived carbon for cancer biomarker detection

-Label-free electrochemical aptasensors for cancer biomarker detection can be a promising means for early detection of cancer due to their high sensitivity, selectivity, and stability, and low cost. In this study, a highly sensitive and selective label-free electrochemical aptasensor based on carbon microelectromechanical systems (C-MEMS) was developed for the detection of platelet-derived growth factor-BB (PDGF-BB). The active electrodes of the aptasensors were synthesized via carbonization of SU-8 derived electrodes at high temperatures in an oxygen-free furnace. An oxygen-plasma oxidation treatment was used to functionalize the C-MEMS electrodes, which provided efficient covalent immobilization of amino terminated affinity aptamers. The turn-off and turn-on detection strategies-based on capacitance and resistance measurement, respectively-were employed. The capacitance detection strategies exhibited a wide linear response range of 0.01-50 nM, with a high sensitivity of 3.33 mF cm-2 Logc-1 (unit of c, nM) and a low limit of detection of 7 pM (S/N = 3). The resistance detection strategies exhibited an even wider linear response range of 0.005-50 nM, and a lower limit of detection of 1.9 pM (S/N = 3), with a high sensitivity of 1.65 × 103 Ω Logc^-1 (unit of c, nM). Both detection strategies provided high selectivity for PDGF-BB and high stability of 90.34% after 10 days. This research demonstrates that the developed label-free electrochemical C-MEMS based PDGF-BB aptasensor is highly sensitive, selective, and robust. This aptasensor is a promising prospect for the highly demanding task of early detection of cancer biomarkers.

Graphene-family materials in electrochemical aptasensors

The study of graphene-based carbon nanocomposites has remarkably increased in recent years. Functionalized graphene-based nanostructures, including graphene oxide and reduced graphene oxide, have great potential as new innovative electrode materials in the fabrication of novel electrochemical sensors. Electrochemical sensors based on aptamers attracted great attention because of their high sensitivity and selectivity, and simple instrumentation, as well as low production cost. Aptamers as a potent alternative to antibodies are functional nucleic acids with a high tendency to specific analytes. Electrochemical aptasensors show specific recognition ability for a wide range of analytes. Although aptamers are selected in vitro in contrast to antibodies, they are interesting due to advantages like high stability, easy chemical modifications, and the potential to be employed in nanostructured device fabrication or electrochemical sensing devices. Recently, new nanomaterials have shown a significant impact on the production of electrochemical sensors with high efficiency and performance. This review aims to give an outline of electrochemical aptasensors based on the graphene family materials and discuss the detection mechanism in this type of aptasensors. The present review summarizes some of the recent achievements in graphene-based aptasensors and includes their recent electroanalytical applications. Graphical Abstract Graphical Abstract.

Target-triggered "signal-off" electrochemical aptasensor assisted by Au nanoparticle-modified sensing platform for high-sensitivity determination of circulating tumor cells

In this study, we fabricated a high-sensitivity "signal-off" electrochemical aptasensing platform for quantifying circulating tumor cells (CTCs) based on target-triggered signal readout of methylene blue (MB). Au nanoparticles (AuNPs) were introduced to enlarge the specific surface area of the gold electrode (GE), which would immobilize homogeneous and more MB-aptamers. MB-modified and stem-loop-like aptamers were assigned as a recognition element with K562 cells. Thiolated complementary strands hybridized with MB-aptamers to form double-stranded DNA (dsDNA) conformation which were further self-assembled on the surface of AuNP-modified GE, leading to a marked current peak of MB signal. In the presence of K562 cells, the MB-aptamers preferred to recognize and bind with the cells, causing the disassembly of MB-aptamers from the GE surface. Therefore, the reduced value of MB signal was related to the number of K562 cells. With the proposed aptasensor, a dynamic linear range from 1 × 10² to 1 × 10⁶ cells mL^-1 was obtained with a detection limit of 23 cells mL^-1. Moreover, the aptasensor showed good selectivity, stability, and reproducibility as well as potential use in the clinical setting. Meanwhile, characterization techniques such as field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, atomic force microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy were performed to analyze the evolution of the morphology and each fabricated step of the constructed aptasensor. Our proposed aptasensor could be designed as a universal platform for CTC determination by replacing tumor cell-specific aptamers, which is a promising strategy for basic research and clinical applications. Graphical abstract.

Bifunctional MOFs-Based Ratiometric Electrochemical Sensor for Multiplex Heavy Metal Ions

In this study, a ratiometric electrochemical sensor based on metal-organic frameworks (MOFs) was developed for sensing of multiplex metal ions. The bifunctional MOFs were prepared in a way to integrate two signal tags and a detection probe. In the presence of target metal ions, the target metal ions can replace the framework metal-ion center in the original MOFs through an ion-exchange reaction, leading to ratiometric electrochemical signals under different applied potentials. One consisted of the Cu²⁺ signal generated from electroactive MOFs selected as internal reference signals. The other consisted of the signal induced by other target metal ions. Using the I_metal ions/I_Cu²⁺ signal as the output, the prepared ratiometric probe was able to eliminate disturbance caused by the sensing environment. Moreover, the large surface area and abundant active sites in MOFs produced a multiplex ratiometric electrochemical sensor with improved characteristics in terms of reproducibility, stability, and sensitivity. The sensor was also simple without sophisticated instrumentation, amplification processes, or an acid dissolution/preconcentration procedure, hence promising for practical applications.

A self-calibrating electrochemical aptasensing platform: Correcting external interference errors for the reliable and stable detection of avian influenza viruses

Conventional electrochemical biosensing systems rely on a single output signal, which limits their certain practical application, specifically from the viewpoint of external interference factors causing electrochemical signal errors. This study reports a self-calibrating dual-electrode based electrochemical aptasensor for the reliable and independent detection of avian influenza viruses (AIVs), which are the primary cause of highly contagious respiratory diseases, under external interference factors. Both electrodes were fabricated using tungsten rods surface-modified with a 3D nanostructured porous silica film (3DNRE). Subsequently, methylene blue (MB) was loaded as a redox-active material into the pores and capped with corresponding aptamer. One electrode was capped with an anti-AIV nucleoprotein (NP) aptamer (Apt_AIV-MB@3DNRE) allowing target-specific binding, resulting in changes in electrochemical signal upon diffusional release of the loaded redox molecules. The other electrode was capped with a control aptamer (Apt_con-MB@3DNRE), serving as a reference to correct false responses generated by nonspecific aptamer detachment and MB release under environmental changes in pH and ion strength and presence of nontarget molecules from cell lysis debris. In the dual-electrode platform, Apt_con-MB@3DNRE provides a corrected baseline for the fluctuating original output signals from Apt_AIV-MB@3DNRE. Consequently, this dual-electrode platform exhibits excellent output-signal stability (relative standard deviation, RSD: 5.86%) compared to a conventional single-electrode platform (RSD: 30.13%) at equivalent concentrations of AIV NP samples under different reaction buffer conditions. Moreover, no further purification and washing steps were required, indicating that the strategy may represent a universal and reliable platform for the electrochemical aptamer-based detection of various biomolecules.

Simultaneous electrochemical determination of ochratoxin A and fumonisin B1 with an aptasensor based on the use of a Y-shaped DNA structure on gold nanorods

A complementary DNA (cDNA) was designed to simultaneously hybridize with the ochratoxin A (OTA) aptamer and the fumonisin B1 (FB1) aptamer to form a unique Y-shaped DNA structure and to achieve simultaneous detection. Gold nanorods (AuNRs) were used to immobilize thionine (Th), thiolated ferrocene (Fc), thiolated OTA aptamer (Apt1), and thiolated FB1 aptamer (Apt2), to form an amplified signal element and a recognition element. The Apt1-AuNRs-Th complex and the Apt2-AuNRs-Fc complex hybridize with cDNA to form a unique Y-DNA structure on a gold electrode. This produces two initial electrochemical signals [with 177 μΑ cm^-2 near -0.2 V, and 3121 μΑ cm^-2 near +0.46 V (vs. Ag/AgCl)] by differential pulse voltammetry. Upon addition of 0.1 ng mL^-1 OTA and 0.1 ng mL^-1 FB1, the aptamers bind the two toxins. This results in the release of Apt1-AuNRs-Th and Apt2-AuNRs-Fc, so the peak currents densities decrease to 115 μΑ cm^-2 and 209 μΑ cm^-2. The assay allows simultaneous determination of OTA and FB1 in the 1.0 pg·mL^-1 to 100 ng·mL^-1 concentration ranges, with LODs of 0.47 and 0.26 pg·mL^-1. The assay is reproducible, stable and specific. It was applied to the determination of OTA and FB1 in spiked beer, with recoveries between 89.0% and 102.0%. Graphical abstractSchematic representation of OTA and FB₁ detection based on Apt₂-AuNRs-Fc/Apt₁-AuNRs-Th/cDNA/AuE. (AuNRs: Gold nanorods; Th: thionine; Fc: ferrocene; SH: thiol; BSA: Bovine serum albumin; cDNA: Complementary DNA; Apt₁: Aptamer1; Apt₂: Aptamer2; OTA: Ochratoxin A; FB₁: Fumonisin B₁).

A multifunctional ratiometric electrochemical sensor for combined determination of indole-3-acetic acid and salicylic acid

For the first time, a multifunctional ratiometric electrochemical sensor was developed for quantifying IAA and SA simultaneously.

NMR studies on oligonucleotide - Methylene blue conjugates targeting double-helical nucleic acids

Methylene blue (MB) - nucleic acid interactions are of considerable interest due to the photosensitizing activity of the dye with potential applications in medicine and biotechnology. Covalent attachment of the MB to an oligonucleotide through a flexible heptamethylene linker enabled a positioning of the dye moiety to specific sites through triplex formation with a target duplex. NMR studies demonstrated interactions of MB with the nucleic acids. In sequences with the MB moiety facing the triplex-duplex junction with an alternating CG duplex overhang next to a T·A·T triple-helical tract, proton resonances experienced severe linebroadening upon MB binding and point to kinetically labile complexes with exchange among different binding modes. For sequences with the MB moiety facing a terminal T·A·T base triad of the triplex tract, structural heterogeneity decreased when compared to a triplex without MB attached to the third strand. Also, the thermal stability of the latter construct increased significantly in the presence of MB, indicating external end stacking as predominant binding mode. Without any obvious disruptions of sequential imino-imino NOE contacts within the triplex and duplex tracts, a most favorable intercalation between T·A·T base triples or CG base pairs is not supported by the present data under our experimental conditions.

Ratiometric electrochemical aptasensor for ultrasensitive detection of Ochratoxin A based on a dual signal amplification strategy: Engineering the binding of methylene blue to DNA

A novel ratiometric electrochemical aptasensor was developed for Ochratoxin A (OTA) detection based on the binding of methylene blue (MB) to DNA with a dual signal amplification strategy. The formation of dsDNA structures between ferrocene-labeled complementary DNA (Fc-cDNA), the OTA aptamer, and complementary helper DNA (hDNA) caused Fc away from the electrode, and allowed dsDNA to bind with a certain amount of MB. Here, a small oxidation current of Fc (I_Fc) and a large oxidation current of MB (I_MB) were obtained. In the presence of OTA, its specific recognition with the aptamer induced the release of aptamer and hDNA from the electrode and subsequently the formation of hairpin structure for cDNA, which caused Fc close to the electrode and a weaker binding ability with MB. Then, an increased I_Fc and a decreased I_MB were obtained. Based on this principle, OTA could be accurately quantified by measuring the ratiometric signal of I_Fc/I_MB. Herein, the dual signal amplification strategy of the introduction of hDNA and the binding with MB after the OTA recognition was exploited to amplify the response signal. The obtained aptasensor showed a linear detection range from 10 pg mL^-1 to 10 ng mL^-1 and a detection limit of 3.3 pg mL^-1. The aptasensor was successfully applied to determine OTA in wheat, and the results were validated through HPLC-MS. Furthermore, by changing the target aptamers, this strategy could be universally used for the determination of various mycotoxins, showing promising potential applications for mycotoxins monitoring in agricultural products and foods.

Nanotechnology and nanomaterial-based no-wash electrochemical biosensors: from design to application

Nanotechnology and nanomaterial based electrochemical biosensors (ECBs) have achieved great development in many fields, such as clinical diagnosis, food analysis, and environmental monitoring. Nowadays, the single-handed pursuit of sensitivity and accuracy cannot meet the demands of detection in many in situ and point-of-care (POC) circumstances. More and more attention has been focused on simplifying the operation procedure and reducing detection time, and thus no-wash assay has become one of the most effective ways for the continuous development of ECBs. However, there are many challenges to realize no-wash detection in the real analysis, such as redox interferences, multiple impurities, non-conducting protein macromolecules, etc. Furthermore, the complex detection circumstance in different application fields makes the realization of no-wash ECBs more complicated and difficult. Thanks to the updated nanotechnology and nanomaterials, in-depth analysis of the obstacles in the detection process and various methods for fabricating no-wash ECBs, most issues have been largely resolved. In this review, we have systematically analyzed the nanomaterial based design strategy of the state-of-the-art no-wash ECBs in the past few years. Following that, we summarized the challenges in the detection process of no-wash ECBs and their applications in different fields. Finally, based on the summary and analysis in this review, we also evaluated and discussed future prospects from the design to the application of ECBs.

Embedded Au Nanoparticles-Based Ratiometric Electrochemical Sensing Strategy for Sensitive and Reliable Detection of Copper Ions

The ratiometric method allows the measurement of ratio changes between two signals, which can reduce the detection signal fluctuations caused by distinct background conditions and greatly improve the reproducibility and reliability of detection. However, in contrast with the emerging dual excitation or dual emission dyes applied in ratiometric luminescence measurement, only a few internal reference probes have been exploited for ratiometric electrochemical detection. In this paper, a gold nanoparticles@carbonized resin nanospheres composite with thermally reduced graphene oxide as scaffold (AuNPs@CRS-TrGNO) has been fabricated, and the AuNPs embedded in the CRS were first used as an internal reference probe for ratiometric electrochemical detection. The detachment and aggregation of AuNPs is suppressed by embedding in the CRS, so its redox signal is very stable, which provides feasibility for ratiometric detection. Moreover, the embedment of AuNPs, carbonization of resin spheres, and hybridization with TrGNO all have played positive roles in improving the charge transfer rate, which leads to excellent electrochemical performance of the composite. Based on these characteristics of the AuNPs@CRS-TrGNO, a new ratiometric electrochemical detection platform was constructed, and copper ions (Cu²⁺) in simulated seawater were successfully detected. This ratiometric method has the advantages of simple design and convenient operation, and obviously it improves the reproducibility and reliability of the electrochemical sensor.

Electrochemical aptamer-based microsensor for real-time monitoring of adenosine in vivo

In this work, an implantable and minimally invasive micro-aptasensor for adenosine monitoring in vivo, based on flexible integrated electrodes, was developed. Firstly the sensor was made by the modification of a needle-type electrode with reduced graphene oxide and gold nanoclusters (rGO-AuNCs) using two-step electrodeposition. Secondly Sulfhydryl-terminated capture probe (ssDNA1) was immobilized on rGO-AuNCs modified electrode surface by self-assembly, and then it was hybridized with adenosine aptamer (ssDNA2). Lastly methylene blue (MB) as an electrochemical indicator was adsorbed on the aptamer through specific interaction of MB with guanine base. The peak current of MB decreased linearly with increasing adenosine concentration due to the formation of aptamer-adenosine complex and displacement of the aptamer from the modified electrode surface. The sensor showed a low detection limit of 0.1 nM with signal-to-noise ratio equal to 3 as well as a wide linear response range (0.1 nM-1 mM) in vitro. Also, a high selectivity was demonstrated for adenosine in relation to uridine, guanosine, and cytidine. Experiments in vivo demonstrated fast responses for a range of adenosine concentrations. This work demonstrates a promising path for implantable devices for the determination of biomolecules in vivo, thus allowing for health tests, detection of infectious diseases, and other medical conditions.

Low Fouling Protein Detection in Complex Biological Media Supported by a Designed Multifunctional Peptide

The construction of sensitive and selective biosensors capable of detecting specific targets in complex biological samples remains a challenge highly relevant to a range of sensor/diagnostic applications. Herein, we have utilized a multifunctional peptide to present an interface that supports the very specific recruitment of targets from serum. The novel peptide sequence designed contains an anchoring domain (CPPPP-), an antifouling domain (-NQNQNQNQDHWRGWVA), and a human immunoglobulin G (IgG) recognition domain (-HWRGWVA), and the whole peptide was designed to be antifouling. These were integrated into polyaniline nanowire arrays in supporting the quantification of IgG (with a limit of detection of 0.26 ng mL^-1) in neat serum and real clinical samples. The strategy of utilizing multisegment peptide films to underpin highly selective target recruitment is, of course, readily extended to a broad range of targets for which an affinity sequence can be generated.

Advances in the design of nanomaterial-based electrochemical affinity and enzymatic biosensors for metabolic biomarkers: A review

This review (with 340 refs) focuses on methods for specific and sensitive detection of metabolites for diagnostic purposes, with particular emphasis on electrochemical nanomaterial-based sensors. It also covers novel candidate metabolites as potential biomarkers for diseases such as neurodegenerative diseases, autism spectrum disorder and hepatitis. Following an introduction into the field of metabolic biomarkers, a first major section classifies electrochemical biosensors according to the bioreceptor type (enzymatic, immuno, apta and peptide based sensors). A next section covers applications of nanomaterials in electrochemical biosensing (with subsections on the classification of nanomaterials, electrochemical approaches for signal generation and amplification using nanomaterials, and on nanomaterials as tags). A next large sections treats candidate metabolic biomarkers for diagnosis of diseases (in the context with metabolomics), with subsections on biomarkers for neurodegenerative diseases, autism spectrum disorder and hepatitis. The Conclusion addresses current challenges and future perspectives. Graphical abstract This review focuses on the recent developments in electrochemical biosensors based on the use of nanomaterials for the detection of metabolic biomarkers. It covers the critical metabolites for some diseases such as neurodegenerative diseases, autism spectrum disorder and hepatitis.