Biofunctionalization of PAMAM-montmorillonite decorated poly (Ɛ-caprolactone)-chitosan electrospun nanofibers for cell adhesion and electrochemical cytosensing

Electrospun nanofibers electrostatically adsorb heterotrophic nitrifying and aerobic denitrifying bacteria to degrade nitrogen in wastewater

Nanofibers were prepared by electrospinning a mixture of polycaprolactone and silica, and modified to improve the hydrophilicity and stability of the material and to degrade nitrogenous wastewater by adsorbing heterotrophic nitrifying aerobic denitrifying (Ochrobactrum anthropic). The immobilized bacteria showed highly efficient simultaneous nitrification-denitrification ability, which could convert nearly 90 % of the initial nitrogen into gaseous nitrogen under aerobic conditions, and the average TN removal rate reached 5.59 mg/L/h. The average ammonia oxidation rate of bacteria immobilized by modified nanofibers was 7.36 mg/L/h, compared with 6.3 mg/L/h for free bacteria and only 4.23 mg/L/h for unmodified nanofiber-immobilized bacteria. Kinetic studies showed that modified nanofiber-immobilized bacteria complied with first-order degradation kinetics, and the effects of extreme pH, temperature, and salinity on immobilized bacteria were significantly reduced, while the degradation rate of free bacteria produced larger fluctuations. In addition, the immobilized bacterial nanofibers were reused five times, and the degradation rate remained stable at more than 80 %. At the same time, the degradation rate can still reach 50 % after 6 months of storage at 4 °C. It also demonstrated good nitrogen removal in practical wastewater treatment.

Biomedical applications of electrospun polycaprolactone-based carbohydrate polymers: A review

Carbohydrate used in biomedical applications is influenced by numerous factors. One of the most appealing characteristic of carbohydrates is their ability to reproduce from natural resources which makes them ecologically friendly. Due to their abundance, biocompatibility, and no contamination by residual initiators, the desire for polysaccharides in medical uses is growing. Research on fiber-based materials, with a variety of medical applications including bio-functional scaffolds, continues to yield novel and intriguing findings. Almost all biopolymers of diverse structural compositions are electrospun to fulfill biomedical usage criteria, and the electrospinning technique is widely employed in biomedical technologies for both in-vivo and in-vitro therapies. Due to its biocompatibility and biodegradability, polycaprolactone (PCL) is employed in medical applications like tissue engineering and drug delivery. Although PCL nanofibers have established effects in vitro, more research is needed before their potential therapeutic application in the clinic. Here we tried to focus mainly on the carbohydrate incorporated PCL-based nanofibers production techniques, structures, morphology, and physicochemical properties along with their usage in biomedicine.

Retention of Phthalates in Wine Using Nanomaterials as Chemically Modified Clays with H20, H30, H40 Boltron Dendrimers

The presence of phthalic acid esters in wines presents a major risk to human health due to their very toxic metabolism. In this paper, aluminosilicate materials were used, with the aim of retaining various pollutants and unwanted compounds in wine. The pollutants tested were di-butyl and di-ethyl hexyl phthalates. They were tested and detected using the gas chromatography-mass spectrometry (CG-MS) analytical technique. Nanomaterials were prepared using sodium bentonite, and were chemically modified via impregnation using three types of Boltron dendrimers of second, third and fourth generations (NBtH20, NBtH30 and NBtH40). The synthesized nanomaterials were characterized using the Brunauer-Emmett-Teller (BET) method, Fourier-transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analysis. In this paper, two aspects were addressed: the first related to the retention of phthalate-type pollutants (phthalic acid esters-PAEs) and the second related to the protein and polyphenol levels in the white wine of the Aligoté grape variety. The results obtained in this study have a major impact on PAEs in wine, especially after treatment with NBtH30 and NBtH40 (volumes of 250-500 μL/10 mL wine), with the retention of the pollutants being up to 85%.

Electrospun Nanofibers including Organic/Inorganic Nanohybrids: Polystyrene- and Clay-Based Architectures in Immunosensor Preparation for Serum Amyloid A

Diagnostic techniques based on biomolecules have application potential that can be realized in many fields, such as disease diagnosis, bioprocess imaging, food/beverage industries, and environmental pollutant imaging. Successful surface immobilization of biomolecules is critical to increasing the stabilization, sensitivity, and selectivity of biomolecules used in bioassay systems. Nanofibers are good candidates for the immobilization of biomolecules owing to many advantages such as morphology and pore size. In this study, montmorillonite (MMT) clay is modified with poly(amidoamine) (PAMAM) generation 3 (PAMAM_G3) and added to polystyrene (PS) solutions, following which PS/MMT-PAMAM_G3 nanofibers are obtained using the electrospinning method. The nanofibers are obtained by testing PS% (wt%) and MMT-PAMAM_G3% (wt%) ratios and characterized with scanning electron microscopy. Antiserum amyloid A antibody (Anti-SAA) is then conjugated to the nanofibers on the electrode surface via covalent bonds using a zero-length cross linker. Finally, the obtained selective surface is used for electrochemical determination of serum amyloid A (SAA) levels. The linear range of PS/MMT-PAMAM/Anti-SAA is between 1 and 200 ng/mL SAA, and the detection limit is 0.57 ng/mL SAA. The applicability of PS/MMT-PAMAM_G3/Anti-SAA is investigated by taking measurements in synthetic saliva and serum both containing SAA.

Novel Approaches to Enzyme-Based Electrochemical Nanobiosensors

Electrochemistry is a genuinely interdisciplinary science that may be used in various physical, chemical, and biological domains. Moreover, using biosensors to quantify biological or biochemical processes is critical in medical, biological, and biotechnological applications. Nowadays, there are several electrochemical biosensors for various healthcare applications, such as for the determination of glucose, lactate, catecholamines, nucleic acid, uric acid, and so on. Enzyme-based analytical techniques rely on detecting the co-substrate or, more precisely, the products of a catalyzed reaction. The glucose oxidase enzyme is generally used in enzyme-based biosensors to measure glucose in tears, blood, etc. Moreover, among all nanomaterials, carbon-based nanomaterials have generally been utilized thanks to the unique properties of carbon. The sensitivity can be up to pM levels using enzyme-based nanobiosensor, and these sensors are very selective, as all enzymes are specific for their substrates. Furthermore, enzyme-based biosensors frequently have fast reaction times, allowing for real-time monitoring and analyses. These biosensors, however, have several drawbacks. Changes in temperature, pH, and other environmental factors can influence the stability and activity of the enzymes, affecting the reliability and repeatability of the readings. Additionally, the cost of the enzymes and their immobilization onto appropriate transducer surfaces might be prohibitively expensive, impeding the large-scale commercialization and widespread use of biosensors. This review discusses the design, detection, and immobilization techniques for enzyme-based electrochemical nanobiosensors, and recent applications in enzyme-based electrochemical studies are evaluated and tabulated.

Development of an Enzymatic Biosensor Using Glutamate Oxidase on Organic-Inorganic-Structured, Electrospun Nanofiber-Modified Electrodes for Monosodium Glutamate Detection

Herein, dendrimer-modified montmorillonite (Mt)-decorated poly-Ɛ-caprolactone (PCL) and chitosan (CHIT)-based nanofibers were prepared. Mt was modified with a poly(amidoamine) generation 1 (PAMAM_G1) dendrimer, and the obtained PAMAM_G1-Mt was incorporated into the PCL-CHIT nanofiber's structure. The PCL-CHIT/PAMAM_G1-Mt nanofibers were conjugated with glutamate oxidase (GluOx) to design a bio-based detection system for monosodium glutamate (MSG). PAMAM_G1-Mt was added to the PCL-CHIT backbone to provide a multipoint binding side to immobilize GluOx via covalent bonds. After the characterization of PCL-CHIT/PAMAM_G1-Mt/GluOx, it was calibrated for MSG. The linear ranges were determined from 0.025 to 0.25 mM MSG using PCL-CHIT/Mt/GluOx and from 0.0025 to 0.175 mM MSG using PCL-CHIT/PAMAMG₁-Mt/GluOx (with a detection limit of 7.019 µM for PCL-CHIT/Mt/GluOx and 1.045 µM for PCL-CHIT/PAMAMG₁-Mt/GluOx). Finally, PCL-CHIT/PAMAMG₁-Mt/GluOx was applied to analyze MSG content in tomato soup without interfering with the sample matrix, giving a recovery percentage of 103.125%. Hence, the nanofiber modification with dendrimer-intercalated Mt and GluOx conjugation onto the formed nanocomposite structures was performed, and the PCL-CHIT/PAMAM_G1-Mt/GluOx system was successfully developed for MSG detection.

3D-printed composite scaffold with gradient structure and programmed biomolecule delivery to guide stem cell behavior for osteochondral regeneration

The fabrication of osteochondral scaffolds with both structural and biochemical cues to regulate endogenous bone marrow-derived mesenchymal stem cells (BMSCs) behavior for cartilage and subchondral bone regeneration is still a challenge. To this end, a composite scaffold (BE-PSA) with gradient structure and programmed biomolecule delivery was prepared by fused deposition modeling (FDM) 3D printing and multi-material-based modification. The 3D-printed polycaprolactone (PCL) scaffold included upper pores of 200 μm for cartilage regeneration and lower pores of 400 μm for bone regeneration. For a sequential modulation of BMSCs behavior, fast-degrading sodium alginate (SA) hydrogel was used to deliver a burst release of E7 peptide to enhance BMSCs migration within 72 h, while a slowly-degrading silk fibroin (SF) porous matrix was used to provide a sustained release of B2A peptide to improve BMSCs dual-lineage differentiation lasting for >300 h, depending on the different degradation rates of SA hydrogel and SF matrix. The BE-PSA scaffold had good biocompatibility and could improve the migration and osteogenic/chondrogenic differentiation of BMSCs. Benefiting from the synergistic effects of spatial structures and programmed biomolecule delivery, the BE-PSA scaffold showed enhanced cartilage and subchondral bone regeneration in rabbit osteochondral defect model. This work not only provides a promising scaffold to guide BMSCs behavior for osteochondral regeneration but also offers a method for the fabrication of tissue engineering biomaterials based on the structural and biochemical modification.

Ionic conductive nanocomposite based on poly(l-lactic acid)/poly(amidoamine) dendrimerelectrospun nanofibrous for biomedical application

The modification of poly (l-lactic acid) (PLLA) electrospun nanofibrous scaffolds was carried out by blending with second-generation poly amidoamine (PAMAM) for enhancement of their ionic conductivity. The samples containing PLLA and various amounts of PAMAM (1%, 3%, 5%, and 7% by wt.) were fabricated by electrospinning techniques. The electrospun fibers were characterized using scanning electron microscopy (SEM), porosity, Fourier-transform infrared (FTIR) spectroscopy, differential scanning calorimetry, contact angle measurement, water uptake measurement, mechanical properties, and electrical properties. Furthermore,in vitrodegradation study and cell viability assay were investigated in biomaterial applications. Creating amide groups through aminolysis reaction was confirmed by FTIR analysis successfully. The results reveal that adding PAMAM caused an increase in fiber diameter, crystallinity percentage, hydrophilicity, water absorption, elongation-at-break, and OE-mesenchymal stem cell viability. It is worth mentioning that this is the first report investigating the conductivity of PLLA/PAMAM nanofiber. The results revealed that by increasing the amount of PAMAM, the ionic conductivity of scaffolds was enhanced by about nine times. Moreover, the outcomes indicated that the presence of PAMAM could improve the limitations of PLLA like hydrophobicity, lack of active group, and poor cell adhesion.

Composite of PLA Nanofiber and Hexadecyl Trimethyl-Ammonium Chloride-Modified Montmorillonite Clay: Fabrication and Morphology

Our research aim is to develop a new composite material via electrospinning and dip coating methodology. Among bioabsorbable polymers, Polylactic acid (PLA) is viewed as a suitable base material for biomedical usages such as drug delivery and wound dressing. Additionally, these bioabsorbable materials can be used for filtration applications in terms of antibacterial activity the integration of hexadecyl trimethyl ammonium chloride-modified montmorillonite (CTAC-MMT) into PLA fibers would improve mechanical and absorption properties of the PLA fibers. This research aimed to investigated a new method of combining electrospun PLA with dip coating of CTAC-MMT solution. Precisely, electrospun PLA nanofibers were treated with methanol and dipped in a CTAC-MMT suspension. The resultant layer composite of PLA nanofibers and CTAC-MMT was then characterized by elemental analysis. For material characterization and morphological structure analysis, we performed FTIR, SEM-EDS, XPS, DSC, and X-ray diffraction. Through mechanical testing and contact angle measurements, it was found that CTAC-MMT shows a slight improvement in mechanical and absorption properties. Results of characterization techniques have shown that CTAC-MMT can be used as a good filler for composites processed through the dip-coating method. Moreover, results also showed that the diameter of microfibers is affected by concentrations of PLA.

A disposable electrochemical sensor based on electrospinning of molecularly imprinted nanohybrid films for highly sensitive determination of the organotin acaricide cyhexatin

Nanofibrous polyporous membranes imprinted with cyhexatin (CYT) were formed via the ordered distribution of the imprints in electrospun nanofibers. The MIPs have a high mass transfer rate and enhanced adsorption capacity. In addition, a printed carbon electrode with enhanced sensitivity was developed via electrochemical fabrication of reduced graphene oxide (rGO) and gold nanoparticles (AuNPs). The molecularly imprinted sensor exhibits excellent selectivity and sensitivity for CYT. The structure and morphology of the nanohybrid films were characterized by using scanning electron microscopy, atomic force microscopy and chronoamperometry. The sensing performances were evaluated by cyclic voltammetry, differential pulse voltammetry and electrochemical impedance spectroscopy by using hexacyanoferrate(IV) as an electrochemical probe. The electrode, best operated at a working potential of around 0.16 V (vs. Ag/AgCl), has a linear response in the 1-800 ng mL^-1 CYT concentration range and a detection limit of 0.17 ng mL^-1 (at S/N = 3). The sensor demonstrated satisfactory recoveries when applied to the determination of CYT in spiked pear samples. Graphical abstract Schematic presentation of the electrochemical sensor for detection of CYT.

Label-free cytosensing of cancer cells based on the interaction between protein and an electron-transfer carbohydrate-mimetic peptide

We used an electron-transfer carbohydrate-mimetic peptide (YYYYC) to construct an electrochemical cytosensing system. Magnetic beads were modified with either asialofetuin (ASF) or soybean agglutinin (SBA) to evaluate the effect on cell sensing. Because SBA binds to the galactose residue that exists at the terminals of the carbohydrate chains in ASF, the target protein was accumulated on the protein magnetic beads. SBA is an example of N-acetylgalactosamine- and galactose-binding proteins that readily combine with YYYYC. When the peptides and protein-immobilized beads competed for a target protein, the peak current of the peptides changed according to the concentration of the protein at the 10^-12 M level. Next, human myeloid leukemia cells (K562 cell) were measured using the peptide and the carbohydrate chains on the cell surface that recognize SBA. The electrode response was linear to the number of K562 cells and ranged from 1.0 × 10² to 5.0 × 10³ cells mL^-1. In addition, detection of a human liver cancer cell (HepG2 cell) was carried out using interactions with the peptide, the ASF receptors in HepG2 cells, and the carbohydrate chains of ASF. The peak currents were proportional and ranged between 5.0 × 10¹ and 1.5 × 10³ cells mL^-1. When the values estimated from an electrochemical process were compared with those obtained by ELISA, the results were within the acceptable range of measurement error.