Bubble-free rapid microfluidic PCR

Complete Prevention of Bubbles in a PDMS-Based Digital PCR Chip with a Multifunction Cavity

In a chamber-based digital PCR (dPCR) chip fabricated with polydimethylsiloxane (PDMS), bubble generation in the chambers at high temperatures is a critical issue. Here, we found that the main reason for bubble formation in PDMS chips is the too-high saturated vapor pressure of water at an elevated temperature. The bubbles should be completely prevented by reducing the initial pressure of the system to under 13.6 kPa to eliminate the effects of increased-pressure water vapor. Then, a cavity was designed and fabricated above the PCR reaction layer, and Parylene C was used as a shell covering the chip. The cavity was used for the negative generator in sample loading, PDMS degassing, PCR solution degassing in the digitization process and water storage in the thermal reaction process. The analysis was confirmed and finally achieved a desirable bubble-free, fast-digitization, valve-free and no-tubing connection dPCR.

A roadmap to high-speed polymerase chain reaction (PCR): COVID-19 as a technology accelerator

The limit of detection (LOD), speed, and cost of crucial COVID-19 diagnostic tools, including lateral flow assays (LFA), enzyme-linked immunosorbent assays (ELISA), and polymerase chain reactions (PCR), have all improved because of the financial and governmental support for the epidemic. The most notable improvement in overall efficiency among them has been seen with PCR. Its significance for human health increased during the COVID-19 pandemic, when it emerged as the commonly used approach for identifying the virus. However, because of problems with speed, complexity, and expense, PCR deployment in point-of-care settings continues to be difficult. Microfluidic platforms offer a promising solution by enabling the development of smaller, more affordable, and faster PCR systems. In this review, we delve into the engineering challenges associated with the advancement of high-speed microfluidic PCR equipment. We introduce criteria that facilitate the evaluation and comparison of factors such as speed, LOD, cycling efficiency, and multiplexing capacity, considering sample volume, fluidics, PCR reactor geometry and materials, as well as heating/cooling methods. We also provide a comprehensive list of commercially available PCR devices and conclude with projections and a discussion regarding the current obstacles that need to be addressed in order to progress further in this field.

Local Microbubble Removal in Polydimethylsiloxane Microchannel by Balancing Negative and Atmospheric Pressures

Long-term experiments using organoids and tissues are crucial for drug development. Microfluidic devices have been regularly used in long-term experiments. However, microbubbles often form in these devices, and they may damage and starve cells. A method involving the application of negative pressure has been reported to remove microbubbles from microfluidic devices composed of polydimethylsiloxane; however, negative pressure affects the cells and tissues in microfluidic devices. In this study, a local microbubble removal method was developed using a microfluidic device with 0.5 mm thin polydimethylsiloxane sidewalls. The thin sidewalls counterbalanced the negative and atmospheric pressures, thereby localizing the negative pressure near the negatively pressurized chamber. Microbubbles were removed within 5 mm of the negatively pressurized chamber; however, those in an area 7 mm and more from the chamber were not removed. Using the local removal method, a long-term perfusion test was performed, and no contact was confirmed between the bubbles and the simulated tissue for 72 h.

Gas transport mechanisms through gas-permeable membranes in microfluidics: A perspective

Gas-permeable membranes (GPMs) and membrane-like micro-/nanostructures offer precise control over the transport of liquids, gases, and small molecules on microchips, which has led to the possibility of diverse applications, such as gas sensors, solution concentrators, and mixture separators. With the escalating demand for GPMs in microfluidics, this Perspective article aims to comprehensively categorize the transport mechanisms of gases through GPMs based on the penetrant type and the transport direction. We also provide a comprehensive review of recent advancements in GPM-integrated microfluidic devices, provide an overview of the fundamental mechanisms underlying gas transport through GPMs, and present future perspectives on the integration of GPMs in microfluidics. Furthermore, we address the current challenges associated with GPMs and GPM-integrated microfluidic devices, taking into consideration the intrinsic material properties and capabilities of GPMs. By tackling these challenges head-on, we believe that our perspectives can catalyze innovative advancements and help meet the evolving demands of microfluidic applications.

Application of microfluidic technologies in forensic analysis

The application of microfluidic technology in forensic medicine has steadily expanded over the last two decades due to the favorable features of low cost, rapidity, high throughput, user-friendliness, contamination-free, and minimum sample and reagent consumption. In this context, bibliometric methods were adopted to visualize the literature information contained in the Science Citation Index Expanded from 1989 to 2022, focusing on the co-occurrence analysis of forensic and microfluidic topics. A deep interpretation of the literature was conducted based on co-occurrence results, in which microfluidic technologies and their applications in forensic medicine, particularly forensic genetics, were elaborated. The purpose of this review is to provide an impartial evaluation of the utilization of microfluidic technology in forensic medicine. Additionally, the challenges and future trends of implementing microfluidic technology in forensic genetics are also addressed.

Bubble-free diatoms polymerase chain reaction

Polymerase chain reaction (PCR) in small fluidic systems not only improves speed and sensitivity of deoxyribonucleic acid (DNA) amplification but also achieves high-throughput quantitative analyses. However, air bubble trapping and growth during PCR has been considered as a critical problem since it causes the failure of DNA amplification. Here we report bubble-free diatom PCR by exploiting a hierarchically porous silica structure of single-celled algae. We show that femtoliters of PCR solution can be spontaneously loaded into the diatom interior without air bubble trapping due to the surface hydrophilicity and pore structure of the diatom. We discover that a large pressure gradient between air bubbles and nanopores rapidly removes residual air bubbles through the periodically arrayed nanopores during thermal cycling. We demonstrate the DNA amplification by diatom PCR without air bubble trapping and growth. Finally, we successfully detect DNA fragments of SARS-CoV-2 with as low as 10 copies/μl by devising a microfluidic device integrated with diatoms assembly. We believe that our work can be applied to many PCR applications for innovative molecular diagnostics and provides new opportunities for naturally abundant diatoms to create innovative biomaterials in real-world applications.

Scalable Processing of Cyclic Olefin Copolymer (COC) Microfluidic Biochips

Microfluidics evolved with the appearance of polydimethylsiloxane (PDMS), an elastomer with a short processing time and the possibility for replication on a micrometric scale. Despite the many advantages of PDMS, there are well-known drawbacks, such as the hydrophobic surface, the absorption of small molecules, the low stiffness, relatively high cost, and the difficulty of scaling up the fabrication process for industrial production, creating a need for alternative materials. One option is the use of stiffer thermoplastics, such as the cyclic olefin copolymer (COC), which can be mass produced, have lower cost and possess excellent properties. In this work, a method to fabricate COC microfluidic structures was developed. The work was divided into process optimization and evaluation of material properties for application in microfluidics. In the processing step, moulding, sealing, and liquid handling aspects were developed and optimized. The resulting COC devices were evaluated from the point of view of molecular diffusion, burst pressure, temperature resistance, and susceptibility to surface treatments and these results were compared to PDMS devices. Lastly, a target DNA hybridization assay was performed showing the potential of the COC-based microfluidic device to be used in biosensing and Lab-on-a-Chip applications.

Micro- and nanosystems for the detection of hemorrhagic fever viruses

Hemorrhagic fever viruses (HFVs) are virulent pathogens that can cause severe and often fatal illnesses in humans. Timely and accurate detection of HFVs is critical for effective disease management and prevention. In recent years, micro- and nano-technologies have emerged as promising approaches for the detection of HFVs. This paper provides an overview of the current state-of-the-art systems for micro- and nano-scale approaches to detect HFVs. It covers various aspects of these technologies, including the principles behind their sensing assays, as well as the different types of diagnostic strategies that have been developed. This paper also explores future possibilities of employing micro- and nano-systems for the development of HFV diagnostic tools that meet the practical demands of clinical settings.

Advances in Simple, Rapid, and Contamination-Free Instantaneous Nucleic Acid Devices for Pathogen Detection

Pathogenic pathogens invade the human body through various pathways, causing damage to host cells, tissues, and their functions, ultimately leading to the development of diseases and posing a threat to human health. The rapid and accurate detection of pathogenic pathogens in humans is crucial and pressing. Nucleic acid detection offers advantages such as higher sensitivity, accuracy, and specificity compared to antibody and antigen detection methods. However, conventional nucleic acid testing is time-consuming, labor-intensive, and requires sophisticated equipment and specialized medical personnel. Therefore, this review focuses on advanced nucleic acid testing systems that aim to address the issues of testing time, portability, degree of automation, and cross-contamination. These systems include extraction-free rapid nucleic acid testing, fully automated extraction, amplification, and detection, as well as fully enclosed testing and commercial nucleic acid testing equipment. Additionally, the biochemical methods used for extraction, amplification, and detection in nucleic acid testing are briefly described. We hope that this review will inspire further research and the development of more suitable extraction-free reagents and fully automated testing devices for rapid, point-of-care diagnostics.

Mini-thermal platform integrated with microfluidic device with on-site detection for real-time DNA amplification

The recent cases of COVID-19 have brought the prospect of and requirement for point-of-care diagnostic devices into the limelight. Despite all the advances in point-of-care devices, there is still a huge requirement for a rapid, accurate, easy-to-use, low-cost, field-deployable and miniaturized PCR assay device to amplify and detect genetic material. This work aims to develop an Internet-of-Things automated, integrated, miniaturized and cost-effective microfluidic continuous flow-based PCR device capable of on-site detection. As a proof of application, the 594-bp GAPDH gene was successfully amplified and detected on a single system. The presented mini thermal platform with an integrated microfluidic device has the potential to be used for the detection of several infectious diseases.

Toward Rapid and Accurate Molecular Diagnostics at Home

The global outbreaks of infectious diseases have significantly driven an imperative demand for rapid and accurate molecular diagnostics. Nucleic acid amplification tests (NAATs) feature high sensitivity and high specificity; however, the labor-intensive sample preparation and nucleic acid amplification steps remain challenging in order to carry out rapid and precision molecular diagnostics at home. This review discusses the advances and challenges of automatic solutions of sample preparation integrated with on-chip nucleic acid amplification for effective and accurate molecular diagnostics at home. The sample preparation methods of whole blood, urine, saliva/nasal swab, and stool on chip are examined. Then, the repurposable integrated sample preparation on a chip using various biological samples is investigated. Finally, the on-chip NAATs that can be integrated with automated sample preparation are evaluated. The user-friendly approaches with combined sample preparation and NAATs can be the game changers for next-generation rapid and precision home diagnostics.

Nucleotide detection mechanism and comparison based on low-dimensional materials: A review

The recent pandemic has led to the fabrication of new nucleic acid sensors that can detect infinitesimal limits immediately and effectively. Therefore, various techniques have been demonstrated using low-dimensional materials that exhibit ultrahigh detection and accuracy. Numerous detection approaches have been reported, and new methods for impulse sensing are being explored. All ongoing research converges at one unique point, that is, an impetus: the enhanced limit of detection of sensors. There are several reviews on the detection of viruses and other proteins related to disease control point of care; however, to the best of our knowledge, none summarizes the various nucleotide sensors and describes their limits of detection and mechanisms. To understand the far-reaching impact of this discipline, we briefly discussed conventional and nanomaterial-based sensors, and then proposed the feature prospects of these devices. Two types of sensing mechanisms were further divided into their sub-branches: polymerase chain reaction and photospectrometric-based sensors. The nanomaterial-based sensor was further subdivided into optical and electrical sensors. The optical sensors included fluorescence (FL), surface plasmon resonance (SPR), colorimetric, and surface-enhanced Raman scattering (SERS), while electrical sensors included electrochemical luminescence (ECL), microfluidic chip, and field-effect transistor (FET). A synopsis of sensing materials, mechanisms, detection limits, and ranges has been provided. The sensing mechanism and materials used were discussed for each category in terms of length, collectively forming a fusing platform to highlight the ultrahigh detection technique of nucleotide sensors. We discussed potential trends in improving the fabrication of nucleotide nanosensors based on low-dimensional materials. In this area, particular aspects, including sensitivity, detection mechanism, stability, and challenges, were addressed. The optimization of the sensing performance and selection of the best sensor were concluded. Recent trends in the atomic-scale simulation of the development of Deoxyribonucleic acid (DNA) sensors using 2D materials were highlighted. A critical overview of the challenges and opportunities of deoxyribonucleic acid sensors was explored, and progress made in deoxyribonucleic acid detection over the past decade with a family of deoxyribonucleic acid sensors was described. Areas in which further research is needed were included in the future scope.

Antenna-enhanced mid-infrared detection of extracellular vesicles derived from human cancer cell cultures

BACKGROUND

Extracellular Vesicles (EVs) are sub-micrometer lipid-bound particles released by most cell types. They are considered a promising source of cancer biomarkers for liquid biopsy and personalized medicine due to their specific molecular cargo, which provides biochemical information on the state of parent cells. Despite this potential, EVs translation process in the diagnostic practice is still at its birth, and the development of novel medical devices for their detection and characterization is highly required.

RESULTS

In this study, we demonstrate mid-infrared plasmonic nanoantenna arrays designed to detect, in the liquid and dry phase, the specific vibrational absorption signal of EVs simultaneously with the unspecific refractive index sensing signal. For this purpose, EVs are immobilized on the gold nanoantenna surface by immunocapture, allowing us to select specific EV sub-populations and get rid of contaminants. A wet sample-handling technique relying on hydrophobicity contrast enables effortless reflectance measurements with a Fourier-transform infrared (FTIR) spectro-microscope in the wavelength range between 10 and 3 µm. In a proof-of-principle experiment carried out on EVs released from human colorectal adenocarcinoma (CRC) cells, the protein absorption bands (amide-I and amide-II between 5.9 and 6.4 µm) increase sharply within minutes when the EV solution is introduced in the fluidic chamber, indicating sensitivity to the EV proteins. A refractive index sensing curve is simultaneously provided by our sensor in the form of the redshift of a sharp spectral edge at wavelengths around 5 µm, where no vibrational absorption of organic molecules takes place: this permits to extract of the dynamics of EV capture by antibodies from the overall molecular layer deposition dynamics, which is typically measured by commercial surface plasmon resonance sensors. Additionally, the described metasurface is exploited to compare the spectral response of EVs derived from cancer cells with increasing invasiveness and metastatic potential, suggesting that the average secondary structure content in EVs can be correlated with cell malignancy.

CONCLUSIONS

Thanks to the high protein sensitivity and the possibility to work with small sample volumes-two key features for ultrasensitive detection of extracellular vesicles- our lab-on-chip can positively impact the development of novel laboratory medicine methods for the molecular characterization of EVs.

Development of an IoT-integrated multiplexed digital PCR system for quantitative detection of infectious diseases

For rapid detection of the COVID-19 infection, the digital polymerase chain reaction (dPCR) with higher sensitivity and specificity has been presented as a promising method of point-of-care testing (POCT). Unlike the conventional real-time PCR (qPCR), the dPCR system allows absolute quantification of the target DNA without a calibration curve. Although a number of dPCR systems have previously been reported, most of these previous assays lack multiplexing capabilities. As different variants of COVID-19 have rapidly emerged, there is an urgent need for highly specific multiplexed detection systems. Additionally, the advances in the Internet of Things (IoT) technology have enabled the onsite detection of infectious diseases. Here, we present an IoT-integrated multiplexed dPCR (IM-dPCR) system involving sample compartmentalization, DNA amplification, fluorescence imaging, and quantitative analysis. This IM-dPCR system comprises three modules: a plasmonic heating-based thermal cycler, a multi-color fluorescence imaging set-up, and a firmware control module. Combined with a custom-developed smartphone application built on an IoT platform, the IM-dPCR system enabled automatic processing, data collection, and cloud storage. Using a self-priming microfluidic chip, 9 RNA groups (e.g., H1N1, H3N2, IFZ B, DENV2, DENV3, DENV4, OC43, 229E, and NL63) associated with three infectious diseases (e.g., influenza, dengue, and human coronaviruses) were analyzed with higher linearity (>98%) and sensitivity (1 copy per μL). The IM-dPCR system exhibited comparable analytical accuracy to commercial qPCR platforms. Therefore, this IM-dPCR system plays a crucial role in the onsite detection of infectious diseases.

Permeation-Enhanced Degassing Method Based on Xylem Embolism Repair and Gas Permeable Materials

Microfluidic devices have developed a wide range of applications in the fields of biomedicine, chemistry, and analytical science. But it is easy to form and accumulate bubbles in microfluidic devices. These bubbles could decrease the detection sensitivity, cause inaccurate analysis results, and even damage the functional region of the device. Inspired by the embolism repair mechanism of angiosperms and the permeability of gas permeable materials, this work proposes a bioinspired permeation-enhanced degassing method. Bionic redundant pits are used in this method to keep bubbles from spreading between microchannels and maintain the continuity of the flow. A hydrophobic gas permeable material is used to enhance the bubble capture capability and accelerate the degassing process. This method can eliminate bubbles automatically and continuously in real time without auxiliary equipment. Compared to the bubble removal only depending on solution in water, the degassing effect of the permeation-enhanced degassing method shows about 1.6 times improvement in the same conditions, and the capability of trapping bubbles is improved by 1.33 times. In this paper, this method was integrated into a concentration gradient generator and a cell culture device. The results show that the concentration gradient generator with degassing structures can dissolve bubbles in a rapid way and reach the stability of the concentration gradient within 5-15 min. The degassing method can run for a long time and improve the cell density and cell viability of HeLa cells up to 2.64 and 1.12 times, respectively. The method has a broad application prospect in microfluidic fields including biomedical fluid processing, virus detection, and microscale reactor operation.

Construction of dPCR and qPCR integrated system based on commercially available low-cost hardware

Fluorescent quantitative PCR (qPCR) and digital PCR (dPCR) are two mainstream nucleic acid quantification technologies. However, commercial dPCR and qPCR instruments have a low integration, a high price, and a large footprint. To solve these shortcomings, we introduce a compound PCR system with both qPCR and dPCR functions. All the hardware used in this compound PCR system is commercially available and low-cost, and free software was used to realize the absolute quantification of nucleic acids. The compound PCR provides two working modes. In the qPCR mode, thermal cycling is realized by controlling the reciprocating motion of the x axis. The heating rate is 1.25 °C s^-1 and the cooling rate is 1.75 °C s^-1. We performed amplification experiments of the PGEM-3zf (+)1 gene. The performance level was similar to commercial qPCR instruments. In the dPCR mode, the heating rate is 0.5 °C s^-1 and the cooling rate is 0.6 °C s^-1. We performed the UPE-Q gene amplification and used the sequential actions of the two-dimensional mechanical sliders to scan the reaction products and used the method of regional statistics and back-inference threshold to get test results. The result we got was 1208 copies per μL^-1, which was similar to expectations.

Micro-PCR chip-based multifunctional ultrafast SARS-CoV-2 detection platform

When dealing with infectious pathogens, the point-of-care screening and diagnosis strategy should be low-cost, simple, rapid and accurate. Here, we report a multifunctional rapid PCR platform allowing both simultaneous screening of suspected cases and accurate identification and quantification of the virus. Based on the platform, samples suspected of being infected with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) are screened first, after which subsequent precise quantification of the virus (SARS-CoV-2) can be performed if necessary. This fast screening technique offers a detection limit of 10 nucleic acid copies per test during the entire running time of 15 minutes, with a throughput of 9 samples at a time. Besides, depending on a droplet microfluidic chip, this platform could also provide assays of nucleic acids across four orders of magnitude of concentration within less than 15 minutes. Additionally, we successfully use the platform to quickly distinguish between positive and negative cases in clinical samples and rapidly quantify the viral load in each sample, which is consistent with standard RT-qPCR tests. As such, we demonstrate a promising and versatile rapid PCR platform for point-of-care diagnosis of infectious diseases.

Emergence of debubblers in microfluidics: A critical review

Bubbles in microfluidics-even those that appear to be negligibly small-are pervasive and responsible for the failure of many biological and chemical experiments. For instance, they block current conduction, damage cell membranes, and interfere with detection results. To overcome this unavoidable and intractable problem, researchers have developed various methods for capturing and removing bubbles from microfluidics. Such methods are multifarious and their working principles are very different from each other. In this review, bubble-removing methods are divided into two broad categories: active debubblers (that require external auxiliary equipment) and passive debubblers (driven by natural processes). In each category, three main types of methods are discussed along with their advantages and disadvantages. Among the active debubblers, those assisted by lasers, acoustic generators, and negative pressure pumps are discussed. Among the passive debubblers, those driven by buoyancy, the characteristics of gas-liquid interfaces, and the hydrophilic and hydrophobic properties of materials are discussed. Finally, the challenges and prospects of the bubble-removal technologies are reviewed to refer researchers to microfluidics and inspire further investigations in this field.

A new dynamic deep learning noise elimination method for chip-based real-time PCR

Point-of-care (POC) real-time polymerase chain reaction (PCR) has become one of the most important technologies for many fields such as pathogen detection and water-quality monitoring. POC real-time PCR usually adopts chips with small-volume chambers for portability, which is more likely to produce complex noise that seriously affects the accuracy. Such complex noises are difficult to be eliminated by the traditional fixed area algorithm that is most commonly used at present because they usually have random shape, location, and brightness. To address this problem, we proposed a novel image analysis method, Dynamic Deep Learning Noise Elimination Method (DIPLOID), in this paper. Our new method could recognize and output the mask of the interference by Mask R-CNN, and then subtract the interference and select the maximum valid contiguous area for brightness analysis by dynamic programming. Compared with the traditional method, DIPLOID increased the accuracy, sensitivity, and specificity from 57.9 to 94.6%, 49.1 to 93.9%, and 65.9 to 95.2%, respectively. DIPLOID has great anti-interference, robustness, and sensitivity, which can reduce the impact of complex noise as much as possible from the aspect of the algorithm. As shown in the experiments of this paper, our method significantly improved the accuracy to over 94% under the complex noise situation, which could make the POC real-time PCR have greater potential in the future.

Microfluidic platforms for extracellular vesicle isolation, analysis and therapy in cancer

Extracellular vesicles (EVs) are small lipidic particles packed with proteins, DNA, messenger RNA and microRNAs of their cell of origin that act as critical players in cell-cell communication. These vesicles have been identified as pivotal mediators in cancer progression and the formation of metastatic niches. Hence, their isolation and analysis from circulating biofluids is envisioned as the next big thing in the field of liquid biopsies for early non-invasive diagnosis and patient follow-up. Despite the promise, current benchtop isolation strategies are not compatible with point-of-care testing in a clinical setting. Microfluidic platforms are disruptive technologies capable of recovering, analyzing, and quantifying EVs within clinical samples with limited volume, in a high-throughput manner with elevated sensitivity and multiplexing capabilities. Moreover, they can also be employed for the controlled production of synthetic EVs and effective drug loading to produce EV-based therapies. In this review, we explore the use of microfluidic platforms for the isolation, characterization, and quantification of EVs in cancer, and compare these platforms with the conventional methodologies. We also highlight the state-of-the-art in microfluidic approaches for EV-based cancer therapeutics. Finally, we analyze the currently active or recently completed clinical trials involving EVs for cancer diagnosis, treatment or therapy monitoring and examine the future of EV-based point-of-care testing platforms in the clinic and EV-based therapy production by the industry.

Bridging the gap between development of point-of-care nucleic acid testing and patient care for sexually transmitted infections

The incidence rates of sexually transmitted infections (STIs), including the four major curable STIs - chlamydia, gonorrhea, trichomoniasis and, syphilis - continue to increase globally, causing medical cost burden and morbidity especially in low and middle-income countries (LMIC). There have seen significant advances in diagnostic testing, but commercial antigen-based point-of-care tests (POCTs) are often insufficiently sensitive and specific, while near-point-of-care (POC) instruments that can perform sensitive and specific nucleic acid amplification tests (NAATs) are technically complex and expensive, especially for LMIC. Thus, there remains a critical need for NAAT-based STI POCTs that can improve diagnosis and curb the ongoing epidemic. Unfortunately, the development of such POCTs has been challenging due to the gap between researchers developing new technologies and healthcare providers using these technologies. This review aims to bridge this gap. We first present a short introduction of the four major STIs, followed by a discussion on the current landscape of commercial near-POC instruments for the detection of these STIs. We present relevant research toward addressing the gaps in developing NAAT-based STI POCT technologies and supplement this discussion with technologies for HIV and other infectious diseases, which may be adapted for STIs. Additionally, as case studies, we highlight the developmental trajectory of two different POCT technologies, including one approved by the United States Food and Drug Administration (FDA). Finally, we offer our perspectives on future development of NAAT-based STI POCT technologies.

Continuous polymerase chain reaction microfluidics integrated with a gold-capped nanoslit sensing chip for Epstein-Barr virus detection

We present the first combination of a microfluidic polymerase chain reaction (PCR) with a gold nanoslit-based surface plasmon resonance (SPR) sensor for detecting the DNA sequence of latent membrane protein 1 (LMP1). The PCR microchannel was produced through a laser scribing technique, and the SPR nanoslit chip was manufactured via hot-embossing nanoimprinting lithography. Afterward, the LMP1 DNA probe was adsorbed onto the SPR chip of the integrated device through electrostatic interactions for further detection. The device can complete the analytical procedure in around 36 min, while the traditional machine requires 105 min to achieve similar signals under the same PCR thermal cycles. The calibration curve with serially diluted LMP1 DNA exhibited the accuracy (R² > 0.99) and sensitivity (limit of detection: ∼10^-11 g/mL) of the device. Moreover, extracted DNA from Epstein-Barr virus (EBV)-positive cells were directly detected through the integrated chip. In brief, this all-in-one chip can amplify gene fragments at the front-end and detect them at the back-end, decreasing the time required for the analysis without compromising accuracy or sensitivity. We believe this label-free, real-time, low-cost device has enormous potential for rapid detection of various viruses, such as EBV and COVID-19.

A sample-to-answer DNA detection microfluidic system integrating sample pretreatment and smartphone-readable gradient plasmonic photothermal continuous-flow PCR

We report a microfluidic system integrating sample pretreatment and smartphone-readable gradient plasmonic photothermal continuous-flow PCR, paving the way for low-cost and rapid implementation of PCR diagnostics.

A plasmonic gold nanofilm-based microfluidic chip for rapid and inexpensive droplet-based photonic PCR

Polymerase chain reaction (PCR) is a powerful tool for nucleic acid amplification and quantification. However, long thermocycling time is a major limitation of the commercial PCR devices in the point-of-care (POC). Herein, we have developed a rapid droplet-based photonic PCR (dpPCR) system, including a gold (Au) nanofilm-based microfluidic chip and a plasmonic photothermal cycler. The chip is fabricated by adding mineral oil to uncured polydimethylsiloxane (PDMS) to suppress droplet evaporation in PDMS microfluidic chips during PCR thermocycling. A PDMS to gold bonding technique using a double-sided adhesive tape is applied to enhance the bonding strength between the oil-added PDMS and the gold nanofilm. Moreover, the gold nanofilm excited by two light-emitting diodes (LEDs) from the top and bottom sides of the chip provides fast heating of the PCR sample to 230 °C within 100 s. Such a design enables 30 thermal cycles from 60 to 95 °C within 13 min with the average heating and cooling rates of 7.37 ± 0.27 °C/s and 1.91 ± 0.03 °C/s, respectively. The experimental results demonstrate successful PCR amplification of the alcohol oxidase (AOX) gene using the rapid plasmonic photothermal cycler and exhibit the great performance of the microfluidic chip for droplet-based PCR.

Integrated Point-of-Care Molecular Diagnostic Devices for Infectious Diseases

The global outbreaks of deadly infectious diseases caused by pathogenic microorganisms have threatened public health worldwide and significantly motivated scientists to satisfy an urgent need for a rapid and accurate detection of pathogens. Traditionally, the culture-based technique is considered as the gold standard for pathogen detection, yet it has a long turnaround time due to the overnight culturing and pathogen isolation. Alternatively, nucleic acid amplification tests provide a relatively shorter turnaround time to identify whether pathogens exist in individuals with high sensitivity and high specificity. In most cases, nucleic acid amplification tests undergo three steps: sample preparation, nucleic acid amplification, and signal transduction. Despite the explosive advancement in nucleic acid amplification and signal transduction technologies, the complex and labor-intensive sample preparation steps remain a bottleneck to create a transformative integrated point-of-care (POC) molecular diagnostic device. Researchers have attempted to simplify and integrate the sample preparations for nucleic acid-based molecular diagnostic devices with innovative progress in integration strategies, engineered materials, reagent storages, and fluid actuation. Therefore, understanding the know-how and obtaining truthful knowledge of existing integrated POC molecular diagnostic devices comprising sample preparations, nucleic acid amplification, and signal transduction can generate innovative solutions to achieve personalized precision medicine and improve global health.In this Account, we discuss the challenges of automated sample preparation solutions integrated with nucleic acid amplification and signal transduction for rapid and precise home diagnostics. Blood, nasal swab, saliva, urine, and stool are emphasized as the most commonly used clinical samples for integrated POC molecular diagnostics of infectious diseases. Even though these five types of samples possess relatively correlated biomarkers due to the human body's circulatory system, each shows unique properties and exclusive advantages for molecular diagnostics in specific situations, which are included in this Account. We examine different integrated POC devices for sample preparation, which includes pathogen isolation and enrichment from the crude sample and nucleic acid purification from isolated pathogens. We present the promising on-chip integration approaches for nucleic acid amplification. We also investigate the on-chip integration methods for reagent storage, which is crucial to simplify the manual operation for end-users. Finally, we present several integrated POC molecular diagnostic devices for infectious diseases. The integrated sample preparation and nucleic acid amplification approach reviewed here can potentially impact the next generation of POC molecular home diagnostic chips, which will significantly impact public health, emergency medicine, and global biosecurity.

Passively driven microfluidic device with simple operation in the development of nanolitre droplet assay in nucleic acid detection

Since nucleic acid amplification technology has become a vital tool for disease diagnosis, the development of precise applied nucleic acid detection technologies in point-of care testing (POCT) has become more significant. The microfluidic-based nucleic acid detection platform offers a great opportunity for on-site diagnosis efficiency, and the system is aimed at user-friendly access. Herein, we demonstrate a microfluidic system with simple operation that provides reliable nucleic acid results from 18 uniform droplets via LAMP detection. By using only micropipette regulation, users are able to control the nanoliter scale of the droplets in this valve-free and pump-free microfluidic (MF) chip. Based on the oil enclosure method and impermeable fabrication, we successfully preserved the reagent inside the microfluidic system, which significantly reduced the fluid loss and condensation. The relative standard deviation (RSD) of the fluorescence intensity between the droplets and during the heating process was < 5% and 2.0%, respectively. Additionally, for different nucleic acid detection methods, the MF-LAMP chip in this study showed good applicability to both genome detection and gene expression analysis.

Rapid PCR powered by microfluidics: A quick review under the background of COVID-19 pandemic

PCR has been widely used in different fields including molecular biology, pathogen detection, medical diagnosis, food detection and etc. However, the difficulty of promoting PCR in on-site point-of-care testing reflects on challenges relative to its speed, convenience, complexity, and even cost. With the emerging state-of-art of microfluidics, rapid PCR can be achieved with more flexible ways in micro-reactors. PCR plays a critical role in the detection of SARS-CoV-2. Under this special background of COVID-19 pandemic, this review focuses on the latest rapid microfluidic PCR. Rapid PCR is concluded in two main features, including the reactor (type, size, material) and the implementation of thermal cycling. Especially, the compromise between speed and sensitivity with microfluidic PCR is explored based on the system ratio of (thermal cycling time)/(reactor size). Representative applications about the detection of pathogens and SARS-CoV-2 viruses based on rapid PCR or other isothermal amplification are discussed as well.

Ultrafast and Real-Time Nanoplasmonic On-Chip Polymerase Chain Reaction for Rapid and Quantitative Molecular Diagnostics

Advent and fast spread of pandemic diseases draw worldwide attention to rapid, prompt, and accurate molecular diagnostics with technical development of ultrafast polymerase chain reaction (PCR). Microfluidic on-chip PCR platforms provide highly efficient and small-volume bioassay for point-of-care diagnostic applications. Here we report ultrafast, real-time, and on-chip nanoplasmonic PCR for rapid and quantitative molecular diagnostics at point-of-care level. The plasmofluidic PCR chip comprises glass nanopillar arrays with Au nanoislands and gas-permeable microfluidic channels, which contain reaction microchamber arrays, a precharged vacuum cell, and a vapor barrier. The on-chip configuration allows both spontaneous sample loading and microbubble-free PCR reaction during which the plasmonic nanopillar arrays result in ultrafast photothermal cycling. After rapid sample loading less than 3 min, two-step PCR results for 40 cycles show rapid amplification in 264 s for lambda-DNA, and 306 s for plasmids expressing SARS-CoV-2 envelope protein. In addition, the in situ cyclic real-time quantification of amplicons clearly demonstrates the amplification efficiencies of more than 91%. This PCR platform can provide rapid point-of-care molecular diagnostics in helping slow the fast-spreading pandemic.

Quantitative Analysis of Fluorescence Detection Using a Smartphone Camera for a PCR Chip

Most existing commercial real-time polymerase chain reaction (RT-PCR) instruments are bulky because they contain expensive fluorescent detection sensors or complex optical structures. In this paper, we propose an RT-PCR system using a camera module for smartphones that is an ultra small, high-performance and low-cost sensor for fluorescence detection. The proposed system provides stable DNA amplification. A quantitative analysis of fluorescence intensity changes shows the camera’s performance compared with that of commercial instruments. Changes in the performance between the experiments and the sets were also observed based on the threshold cycle values in a commercial RT-PCR system. The overall difference in the measured threshold cycles between the commercial system and the proposed camera was only 0.76 cycles, verifying the performance of the proposed system. The set calibration even reduced the difference to 0.41 cycles, which was less than the experimental variation in the commercial system, and there was no difference in performance.

Point-of-Care PCR Assays for COVID-19 Detection

Molecular diagnostics has been the front runner in the world's response to the COVID-19 pandemic. Particularly, reverse transcriptase-polymerase chain reaction (RT-PCR) and the quantitative variant (qRT-PCR) have been the gold standard for COVID-19 diagnosis. However, faster antigen tests and other point-of-care (POC) devices have also played a significant role in containing the spread of SARS-CoV-2 by facilitating mass screening and delivering results in less time. Thus, despite the higher sensitivity and specificity of the RT-PCR assays, the impact of POC tests cannot be ignored. As a consequence, there has been an increased interest in the development of miniaturized, high-throughput, and automated PCR systems, many of which can be used at point-of-care. This review summarizes the recent advances in the development of miniaturized PCR systems with an emphasis on COVID-19 detection. The distinct features of digital PCR and electrochemical PCR are detailed along with the challenges. The potential of CRISPR/Cas technology for POC diagnostics is also highlighted. Commercial RT-PCR POC systems approved by various agencies for COVID-19 detection are discussed.

Lateral Degassing Method for Disposable Film-Chip Microfluidic Devices

It is critical to develop a fast and simple method to remove air bubbles inside microchannels for automated, reliable, and reproducible microfluidic devices. As an active degassing method, this study introduces a lateral degassing method that can be easily implemented in disposable film-chip microfluidic devices. This method uses a disposable film-chip microchannel superstrate and a reusable substrate, which can be assembled and disassembled simply by vacuum pressure. The disposable microchannel superstrate is readily fabricated by bonding a microstructured polydimethylsiloxane replica and a silicone-coated release polymeric thin film. The reusable substrate can be a plate that has no function or is equipped with the ability to actively manipulate and sense substances in the microchannel by an elaborately patterned energy field. The degassing rate of the lateral degassing method and the maximum available pressure in the microchannel equipped with lateral degassing were evaluated. The usefulness of this method was demonstrated using complex structured microfluidic devices, such as a meandering microchannel, a microvortex, a gradient micromixer, and a herringbone micromixer, which often suffer from bubble formation. In conclusion, as an easy-to-implement and easy-to-use technique, the lateral degassing method will be a key technique to address the bubble formation problem of microfluidic devices.

Magnetic Bead Chain-Based Continuous-Flow DNA Extraction for Microfluidic PCR Detection of Salmonella

Nucleic acid extraction is crucial for PCR detection of pathogenic bacteria to ensure food safety. In this study, a new magnetic extraction method was developed using 3D printing and magnetic silica beads (MSBs) to extract the target DNA from a large volume of bacterial sample and combined with microfluidic PCR to determine the bacteria. After proteinase K was added into a bacterial sample to lyse the bacteria and release the DNA, it was continuous-flow injected into the serpentine channel of the extraction chip, where magnetic silica bead chains had been formed in advance using a homogeneous magnetic field generated by two concentric semicircle magnets to capture the MSBs. Then, the flowing DNA was captured by the MSB chains, washed with alcohol, dried with gas, and eluted with deionized water to obtain the purified and concentrated DNA. Finally, the extracted DNA templates were injected into a microfluidic PCR chip with lyophilized amplification reagents and determined using a commercial qPCR device. The experimental results showed that the DNA extraction efficiency was more than 90%, and the lower detection limit of Salmonella was 10² CFU/mL. This new Salmonella detection method is promising to provide the rapid, sensitive, and simultaneous detection of multiple foodborne pathogens.

Multiplex Molecular Point-of-Care Test for Syndromic Infectious Diseases

Point-of-care (POC) molecular diagnostics for clinical microbiology and virology has primarily focused on the detection of a single pathogen. More recently, it has transitioned into a comprehensive syndromic approach that employs multiplex capabilities, including the simultaneous detection of two or more pathogens. Multiplex POC tests provide higher accuracy to for actionable decisionmaking in critical care, which leads to pathogen-specific treatment and standardized usages of antibiotics that help prevent unnecessary processes. In addition, these tests can be simple enough to operate at the primary care level and in remote settings where there is no laboratory infrastructure. This review focuses on state-of-the-art multiplexed molecular point-of-care tests (POCT) for infectious diseases and efforts to overcome their limitations, especially related to inadequate throughput for the identification of syndromic diseases. We also discuss promising and imperative clinical POC approaches, as well as the possible hurdles of their practical applications as front-line diagnostic tests.

Carbon Nanomaterials for Biomedical Application

The use of carbon-based nanomaterials (CNs) with outstanding properties has been rising in many scientific and industrial application fields. These CNs represent a tunable alternative for applications with biomolecules, which allow interactions in either covalent or noncovalent way. Diverse carbon-derived nanomaterial family exhibits unique features and has been widely exploited in various biomedical applications, including biosensing, diagnosis, cancer therapy, drug delivery, and tissue engineering. In this chapter, we aim to present an overview of CNs with a particular interest in intrinsic structural, electronic, and chemical properties. In particular, the detailed properties and features of CNs and its derivatives, including carbon nanotube (CNT), graphene, graphene oxide (GO), and reduced GO (rGO) are summarized. The interesting biomedical applications are also reviewed in order to offer an overview of the possible fields for scientific and industrial applications of CNs.

Bioluminescent detection of isothermal DNA amplification in microfluidic generated droplets and artificial cells

Microfluidic droplet generation affords precise, low volume, high throughput opportunities for molecular diagnostics. Isothermal DNA amplification with bioluminescent detection is a fast, low-cost, highly specific molecular diagnostic technique that is triggerable by temperature. Combining loop-mediated isothermal nucleic acid amplification (LAMP) and bioluminescent assay in real time (BART), with droplet microfluidics, should enable high-throughput, low copy, sequence-specific DNA detection by simple light emission. Stable, uniform LAMP–BART droplets are generated with low cost equipment. The composition and scale of these droplets are controllable and the bioluminescent output during DNA amplification can be imaged and quantified. Furthermore these droplets are readily incorporated into encapsulated droplet interface bilayers (eDIBs), or artificial cells, and the bioluminescence tracked in real time for accurate quantification off chip. Microfluidic LAMP–BART droplets with high stability and uniformity of scale coupled with high throughput and low cost generation are suited to digital DNA quantification at low template concentrations and volumes, where multiple measurement partitions are required. The triggerable reaction in the core of eDIBs can be used to study the interrelationship of the droplets with the environment and also used for more complex chemical processing via a self-contained network of droplets, paving the way for smart soft-matter diagnostics.

One-Step Nucleic Acid Purification and Noise-Resistant Polymerase Chain Reaction by Electrokinetic Concentration for Ultralow-Abundance Nucleic Acid Detection

Nucleic acid amplification tests (NAATs)integrated on a chip hold great promise for point-of-care diagnostics. Currently, nucleic acid (NA) purification remains time-consuming and labor-intensive, and it takes extensive efforts to optimize the amplification chemistry. Using selective electrokinetic concentration, we report one-step, liquid-phase NA purification that is simpler and faster than conventional solid-phase extraction. By further re-concentrating NAs and performing polymerase chain reaction (PCR) in a microfluidic chamber, our platform suppresses non-specific amplification caused by non-optimal PCR designs. We achieved the detection of 5 copies of M. tuberculosis genomic DNA (equaling 0.3 cell) in real biofluids using both optimized and non-optimal PCR designs, which is 10- and 1000-fold fewer than those of the standard bench-top method, respectively. By simplifying the workflow and shortening the development cycle of NAATs, our platform may find use in point-of-care diagnosis.

Ultrasensitive Stress Biomarker Detection Using Polypyrrole Nanotube Coupled to a Field-Effect Transistor

Stress biomarkers such as hormones and neurotransmitters in bodily fluids can indicate an individual’s physical and mental state, as well as influence their quality of life and health. Thus, sensitive and rapid detection of stress biomarkers (e.g., cortisol) is important for management of various diseases with harmful symptoms, including post-traumatic stress disorder and depression. Here, we describe rapid and sensitive cortisol detection based on a conducting polymer (CP) nanotube (NT) field-effect transistor (FET) platform. The synthesized polypyrrole (PPy) NT was functionalized with the cortisol antibody immunoglobulin G (IgG) for the sensitive and specific detection of cortisol hormone. The anti-cortisol IgG was covalently attached to a basal plane of PPy NT through an amide bond between the carboxyl group of PPy NT and the amino group of anti-cortisol IgG. The resulting field-effect transistor-type biosensor was utilized to evaluate various cortisol concentrations. Cortisol was sensitively measured to a detection limit of 2.7 × 10⁻¹⁰ M (100 pg/mL), with a dynamic range of 2.7 × 10⁻¹⁰ to 10⁻⁷ M; it exhibited rapid responses (<5 s). We believe that our approach can serve as an alternative to time-consuming and labor-intensive health questionnaires; it can also be used for diagnosis of underlying stress-related disorders.

Ultrafast Photonic PCR Based on Photothermal Nanomaterials

Over the past few decades, PCR has been the gold standard for detecting nucleic acids (NAs) in various biomedical fields. However, there are several limitations associated with conventional PCR, such as complicated operation, need for bulky equipment, and, in particular, long thermocycling time. Emerging nanomaterials with photothermal effects have shown great potential for developing a new generation of PCR: ultrafast photonic PCR. Here, we review recent applications of photothermal nanomaterials in ultrafast photonic PCR. First, we introduce emerging photothermal nanomaterials and their light-to-heat energy conversion process in photonic PCR. We then review different photothermal nanomaterial-based photonic PCRs and compare their merits and drawbacks. Finally, we summarize existing challenges with photonic PCR and hypothesize its promising future research directions.

A microfluidic alternating-pull-push active digitization method for sample-loss-free digital PCR

Digital polymerase chain reaction (dPCR) is a powerful tool for genetic analysis, providing superior sensitivity and accuracy. In many applications that demand minuscule reaction volumes, such as single cell analysis, efficient and reproducible sample handling and digitization is pivotal for accurate absolute quantification of targets, but remains a significant technical challenge. In this paper, we described a robust and flexible microfluidic alternating-pull-push active digitization (μAPPAD) strategy that confers close to 100% sample digitization efficiency for microwell-based dPCR. Our strategy employs pneumatic valve control to periodically manipulate air pressure inside the chip to greatly facilitate the vacuum-driven partition of solution into microwells, enabling efficient digitization of a small-volume solution with significantly reduced volume variability. The μAPPAD method was evaluated on both tandem-channel and parallel-channel chips, which achieved a digitization efficiency of 99.5 ± 0.3% and 94.6 ± 0.9% within 10.5 min and 2 min, respectively. To assess the analytical performance of the μAPPAD chip, we calibrated it for absolution dPCR quantitation of λDNA across a range of concentrations. The results obtained with our chip matched well with the theoretical curve computed from Poisson statistics. Compared to the existing methods for highly efficient sample digitization, not only does our technology greatly reduce the constraints on microwell geometries and channel design, but also benefits from the intrinsic amenability of the pneumatic valve technique with device integration and automation. Thus we envision that the μAPPAD technology will provide a scalable and widely adaptable platform to promote the development of advanced lab-on-a-chip systems integrating microscale sample processing with dPCR for a broad scope of applications, such as single cell analysis of tumor heterogeneity and genetic profiling of circulating exosomes directly in clinical samples.

Point-of-Care Strategies for Detection of Waterborne Pathogens

Waterborne diseases that originated due to pathogen microorganisms are emerging as a serious global health concern. Therefore, rapid, accurate, and specific detection of these microorganisms (i.e., bacteria, viruses, protozoa, and parasitic pathogens) in water resources has become a requirement of water quality assessment. Significant research has been conducted to develop rapid, efficient, scalable, and affordable sensing techniques to detect biological contaminants. State-of-the-art technology-assisted smart sensors have improved features (high sensitivity and very low detection limit) and can perform in a real-time manner. However, there is still a need to promote this area of research, keeping global aspects and demand in mind. Keeping this view, this article was designed carefully and critically to explore sensing technologies developed for the detection of biological contaminants. Advancements using paper-based assays, microfluidic platforms, and lateral flow devices are discussed in this report. The emerging recent trends, mainly point-of-care (POC) technologies, of water safety analysis are also discussed here, along with challenges and future prospective applications of these smart sensing technologies for water health diagnostics.

Emerging ultrafast nucleic acid amplification technologies for next-generation molecular diagnostics

Over the last decade, nucleic acid amplification tests (NAATs) including polymerase chain reaction (PCR) were an indispensable methodology for diagnosing cancers, viral and bacterial infections owing to their high sensitivity and specificity. Because the NAATs can recognize and discriminate even a few copies of nucleic acid (NA) and species-specific NA sequences, NAATs have become the gold standard in a wide range of applications. However, limitations of NAAT approaches have recently become more apparent by reason of their lengthy run time, large reaction volume, and complex protocol. To meet the current demands of clinicians and biomedical researchers, new NAATs have developed to achieve ultrafast sample-to-answer protocols for the point-of-care testing (POCT). In this review, ultrafast NA-POCT platforms are discussed, outlining their NA amplification principles as well as delineating recent advances in ultrafast NAAT applications. The main focus is to provide an overview of NA-POCT platforms in regard to sample preparation of NA, NA amplification, NA detection process, interpretation of the analysis, and evaluation of the platform design. Increasing importance will be given to innovative, ultrafast amplification methods and tools which incorporate artificial intelligence (AI)-associated data analysis processes and mobile-healthcare networks. The future prospects of NA POCT platforms are promising as they allow absolute quantitation of NA in individuals which is essential to precision medicine.