Engineering of CdTe/SiO2 nanocomposites: Enhanced signal amplification and biocompatibility for electrochemiluminescent immunoassay of alpha-fetoprotein

Electrochemiluminescence of Ultrasmall Silica Nanoparticles from Size Modulation and Multipath Surface State Adjustment for Ultrasensitive HIV-DNA Fragment Detection

Here, ultrasmall SiO2 nanoparticles (u-SiO2 NPs, <5 nm) with obvious electrochemiluminescence (ECL) phenomenon, which was absent for conventional silica nanoparticles (c-SiO2 NPs), were reported. In a finite ultrasmall volume, the u-SiO2 NPs exhibited increasing ground state energy and higher optical absorption strength due to the electron-hole confinement model and favored catalyzing the reaction through the rapid diffusion of bulk charge, resulting in apparent ECL emission. Then, Zn2+-induced u-SiO2 nanoaggregates (Zn/u-SiO2-Ov nAGG) were synthesized and exhibited improved ECL performance via multipath surface state adjustment of u-SiO2 from several aspects, including aggregation-induced ECL, the generation of oxygen vacancy (Ov), and more positive surface charge. In addition, an ECL biosensor was constructed for ultrasensitive human immunodeficiency virus-related deoxyribonucleic acid detection from 100 aM to 1 nM with a low limit of 50.48 aM, combining the ECL luminescence of Zn/u-SiO2-Ov nAGG with three-dimensional DNA nanomachine-mediated multioutput amplification for enhanced accuracy and sensitivity compared to the single-output method. Therefore, exploring the ECL of ultrasmall nanoparticles via the adjustment of size and surface state provided a valuable indication to a wider investigation and application of novel ECL materials for clinical diagnostic.

Application and outlook of electrochemical technology in single-cell analysis

Cellular heterogeneity, especially in some important diseased cells like tumor cells, acts as an invisible driver for disease development like cancer progression in the tumor ecosystem, contributing to differences in the macroscopic and microscopic detection of disease lesions like tumors. Traditional analysis techniques choose group information masked by the mean as the analysis sample, making it difficult to achieve precise diagnosis and target treatment, on which could be shed light via the single-cell level determination/bioanalysis. Hence, in this article we have reviewed the special characteristic differences among various kinds of typical single-cell bioanalysis strategies and electrochemical techniques, and then focused on the recent advance and special bio-applications of electrochemiluminescence and micro-nano electrochemical sensing mediated in single-cell bioimaging & bioanalysis. Especially, we have summarized the relevant research exploration of the possibility to establish the in-situ single-cell electrochemical methods to detect cell heterogeneity through determination of specific biomolecules and bioimaging of some important biological processes. Eventually, this review has explored some important advances of electrochemical single-cell detection techniques for the real-time cellular bioimaging and diagnostics of some disease lesions like tumors. It raises the possibility to provide the specific in-situ platform to exploit the versatile, sensitive, and high-resolution electrochemical single-cell analysis for the promising biomedical applications like rapid tracing of some disease lesions or in vivo bioimaging for precise cancer theranostics.

Electrochemiluminescence of Semiconductor Quantum Dots and Its Biosensing Applications: A Comprehensive Review

Electrochemiluminescence (ECL) is the chemiluminescence triggered by electrochemical reactions. Due to the unique excitation mode and inherent low background, ECL has been a powerful analytical technique to be widely used in biosensing and imaging. As an emerging ECL luminophore, semiconductor quantum dots (QDs) have apparent advantages over traditional molecular luminophores in terms of luminescence efficiency and signal modulation ability. Therefore, the development of an efficient ECL system with QDs as luminophores is of great significance to improve the sensitivity and detection flux of ECL biosensors. In this review, we give a comprehensive summary of recent advances in ECL using semiconductor QDs as luminophores. The luminescence process and ECL mechanism of semiconductor QDs with various coreactants are discussed first. Specifically, the influence of surface defects on ECL performance of semiconductor QDs is emphasized and several typical ECL enhancement strategies are summarized. Then, the applications of semiconductor QDs in ECL biosensing are overviewed, including immunoassay, nucleic acid analysis and the detection of small molecules. Finally, the challenges and prospects of semiconductor QDs as ECL luminophores in biosensing are featured.

High electrochemical active Au-NP/2D zinc-metal organic frameworks heterostructure-based ECL sensor for the miRNA-522 detection in triple negative breast cancer

In this work, a novel electrochemiluminescence (ECL) sensor has been developed to detect the miRNA-522 in the tumor tissues of triple-negative breast cancer (TNBC) patients. Au NPs/Zn MOF heterostructure was obtained by in situ growth and used as novel luminescence probe. Firstly, zinc-metal organic framework nanosheets (Zn MOF NSs) were synthesized with Zn²⁺ as the central metal ion and 2-aminoterephthalic acid (NH₂-BDC) as the ligand. 2D MOF nanosheets with ultra-thin layered structure and relatively large specific surface areas can enhance the catalytic activity in the ECL generation. Furthermore, the electron transfer capacity and the electrochemical active surface area of MOF were greatly improved by the growth of Au NPs. Therefore, Au NPs/Zn MOF heterostructure showed the significant electrochemical activity in the sensing process. In addition, the magnetic Fe₃O₄@SiO₂@Au microspheres were used as capture units in the magnetic separation step. The magnetic spheres with hairpin aptamer H1 can capture target gene. Then the captured miRNA-522 triggered the target catalyzed hairpin assembly (CHA) sensing process and linked Au NPs/Zn MOF heterostructure. The concentration of miRNA-522 can be quantified by the ECL signal enhancement of the Au NPs/Zn MOF heterostructure. Due to the high catalytic activity of Au NPs/Zn MOF heterostructure and their unique structural and electrochemical properties, the prepared ECL sensor achieved high-sensitive detection of miRNA-522 in the range of 1 fM to 0.1 nM with the detection limit of 0.3 fM. This strategy can provide a potential alternative for miRNA detection in medical research and clinical diagnosis of triple negative breast cancer.

Luminophore-Surface-Engineering-Enabled Low-Triggering-Potential and Coreactant-Free Electrochemiluminescence for Protein Determination

Coreactant-free electrochemiluminescence (ECL) is promising for removing the exogenous effects of coreactant and simplify the operation procedures and setups of commercialized ECL bioassays. Herein, an electrosterically involved strategy for achieving a low-triggering-potential (+0.21 V vs Ag/AgCl) and coreactant-free ECL from dual-stabilizer-capped CdTe nanocrystals (NCs) is proposed with mercaptopropionic acid (MPA) and hexametaphosphate (HMP) as the capping agents of luminophores. Upon employing the CdTe NCs as the ECL tag for the immunoassay, all the tags in the bioconjugates of the CdTe NCs and the secondary antibody (Ab₂|CdTe) as well as in the final achieved sandwich-type immunocomplexes can exhibit efficient coreactant-free ECL with an electrosterically involved triggering potential nature. The bioconjugates of Ab₂|CdTe with Ab₂ no more than 30 kDa, such as the thyroid stimulating hormone (30 kDa) and the recombinant pro-gastrin releasing peptide (ProGRP, 14 kDa), merely exhibit coreactant-free ECL around +0.24 V, while bioconjugates of Ab₂|CdTe with an Ab₂ beyond 30 kDa only give off coreactant-free ECL around +0.82 V. Due to the further enhanced electrosteric effect in sandwich-type immunocomplexes, only the ECL immunosensor with ProGRP as the target can give off coreactant-free ECL around +0.24 V. The electrosterically involved and coreactant-free ECL of CdTe NCs is consequently utilized to sensitively and selectively determine the molecular protein ProGRP, which demonstrates a wide linearity range from 0.1 to 2000 pg/mL and a low limit of detection at 0.05 pg/mL (S/N = 3). This low-triggering-potential and coreactant-free combined ECL platform indicates that engineering the surface of CdTe NCs with a protein can improve the performance of ECL tags in a protein-weight-involved electrosterical way.

A photoelectrochemical immunosensing platform for ultrasensitive detection of alpha-fetoprotein based on a signal amplification strategy

For the first time, a PEC immunosensor based on a signal amplification strategy is successfully constructed to quantitatively detect alpha-fetoprotein in serum sample. Three favorable factors explain the ultra-high sensitivity of this method. Firstly, compared with pure BiPO₄, the BiPO₄/BiOBr heterojunction has a narrower band gap, which expands the light absorption range and enables the light energy to be fully utilized. Secondly, the separation of photogenerated electrons and hole pairs during PEC detection is due to the efficient matching of energy levels among BiPO₄, BiOBr and CdS, inhibiting the recombination of photogenerated electrons, which improves the performance of PEC immunosensor. Thirdly, due to the presence of CdS, the light absorption capability of the sensor is enhanced, more electron-hole pairs are generated, and the photocurrent signal is increase. Under the optimal conditions, the PEC immunosensor shows a wide linear range of 0.001-1000 ng/mL for AFP and a low detection limit of 0.82 pg/mL. The PEC immunosensor developed in this experiment has excellent reproducibility, stability and high sensitivity, and also achieves satisfactory results in the analysis of human serum samples, establishing a new analytical method for biomarker detection.

Recent advances in quantum dot-based fluorescence-linked immunosorbent assays

Fluorescence immunoassays have been given considerable attention among the quantitative detection methods in the clinical medicine and food safety testing fields. In particular, semiconductor quantum dots (QDs) have become ideal fluorescent probes for highly sensitive and multiplexed detection due to their unique photophysical properties, and the QD fluorescence-linked immunosorbent assay (FLISA) with high sensitivity, high accuracy, and high throughput has been greatly developed recently. In this manuscript, the advantages of applying QDs to FLISA platforms and some strategies for their application to in vitro diagnostics and food safety are discussed. Given the rapid development of this field, we classify these strategies based on the combination of QD types and detection targets, including traditional QDs or QD micro/nano-spheres-FLISA, and multiple FLISA platforms. In addition, some new sensors based on the QD-FLISA are introduced; this is one of the hot spots in this field. The current focus and future direction of QD-FLISA are also discussed, which provides important guidance for the further development of FLISA.

Recent advances in nanotechnology-enhanced biosensors for α-fetoprotein detection

α-Fetoprotein (AFP) is a kind of fetal protein that is related to tumor, the increasing concentration of which gives birth to a large variety of diseases, such as liver cancer. Therefore, the detection method with super sensitivity, high selectivity, and less time consumption under trace concentrations in early stage of diseases is becoming a necessity. In recent years, nanomaterials have been regarded as significant resources for the exploration of efficient biosensors with high sensitivity, selectivity, speed, as well as simple process, due to their excellent optical, electrical, and chemical properties. In this paper, we reviewed the research progress of AFP biosensors with enhanced sensitivity and selectivity by nanoparticles. Representative examples have also been displayed in this paper to expound the nanotechnologies utilized in the early detection of AFP. Furthermore, challenges of the clinical application of AFP biosensors based on nanotechnology have been elaborated, as well as the development opportunity in this field in the future. This review provides a comprehensive overview on the various nano-biosensor for AFP detection based on functional nanotechnology.

Clinically Applicable Homogeneous Assay for Serological Diagnosis of Alpha-Fetoprotein by Impact Electrochemistry

Tumor protein quantification with high specificity, sensitivity, and efficiency is of great significance to enable early diagnosis and effective treatment. The existing methods for protein analysis usually suffer from high cost, time-consuming operation, and insufficient sensitivity, making them not clinically friendly. In this work, a label-free homogeneous sensor based on the nano-impact electroanalytic (NIE) technique was proposed for the detection of tumor protein marker alpha-fetoprotein (AFP). The detection principle is based on the recovery of current of single PtNP catalyzed hydrazine oxidation due to the release of the pre-adsorbed passivating aptamers on PtNPs from the competition of the stronger binding between the specific interaction of the AFP aptamer and AFP. The intrinsic one-by-one analytical ability of NIE allows highly sensitive detection, which can be further improved by reducing the reaction/incubation volume. Meanwhile, the current sensor avoids a laborious labeling procedure as well as the separation and washing steps due to the in situ characteristic of NIE. Accordingly, the current sensor enables efficient, highly sensitive, and specific AFP analysis. More importantly, the reliable detection of AFP in diluted real sera from hepatocellular carcinoma (HCC) patients is successfully achieved, indicating that the impact electrochemistry-based sensing platform has great potential to be applied in point-of-care devices for HCC liquid biopsy.

Magnetic soft robotic bladder for assisted urination

The poor contractility of the detrusor muscle in underactive bladders (UABs) fails to increase the pressure inside the UAB, leading to strenuous and incomplete urination. However, existing therapeutic strategies by modulating/repairing detrusor muscles, e.g., neurostimulation and regenerative medicine, still have low efficacy and/or adverse effects. Here, we present an implantable magnetic soft robotic bladder (MRB) that can directly apply mechanical compression to the UAB to assist urination. Composed of a biocompatible elastomer composite with optimized magnetic domains, the MRB enables on-demand contraction of the UAB when actuated by magnetic fields. A representative MRB for a UAB in a porcine model is demonstrated, and MRB-assisted urination is validated by in situ computed tomography imaging after 14-day implantation. The urodynamic tests show a series of successful urination with a high pressure increase and fast urine flow. Our work paves the way for developing MRB to assist urination for humans with UABs.

Progress and Prospects of Electrochemiluminescence Biosensors Based on Porous Nanomaterials

Porous nanomaterials have attracted much attention in the field of electrochemiluminescence (ECL) analysis research because of their large specific surface area, high porosity, possession of multiple functional groups, and ease of modification. Porous nanomaterials can not only serve as good carriers for loading ECL luminophores to prepare nanomaterials with excellent luminescence properties, but they also have a good electrical conductivity to facilitate charge transfer and substance exchange between electrode surfaces and solutions. In particular, some porous nanomaterials with special functional groups or centered on metals even possess excellent catalytic properties that can enhance the ECL response of the system. ECL composites prepared based on porous nanomaterials have a wide range of applications in the field of ECL biosensors due to their extraordinary ECL response. In this paper, we reviewed recent research advances in various porous nanomaterials commonly used to fabricate ECL biosensors, such as ordered mesoporous silica (OMS), metal-organic frameworks (MOFs), covalent organic frameworks (COFs) and metal-polydopamine frameworks (MPFs). Their applications in the detection of heavy metal ions, small molecules, proteins and nucleic acids are also summarized. The challenges and prospects of constructing ECL biosensors based on porous nanomaterials are further discussed. We hope that this review will provide the reader with a comprehensive understanding of the development of porous nanomaterial-based ECL systems in analytical biosensors and materials science.

In situ growth of WO3/BiVO4 nanoflowers onto cellulose fibers to construct photoelectrochemical/colorimetric lab-on-paper devices for the ultrasensitive detection of AFP

In this work, novel dual-mode lab-on-paper devices based on in situ grown WO₃/BiVO₄ heterojunctions onto cellulose fibers, as signal amplification probes, were successfully fabricated by the integration of photoelectrochemical (PEC)/colorimetric analysis technologies into a paper sensing platform for the ultrasensitive detection of alpha-fetoprotein (AFP). Specifically, to achieve an impressive PEC performance of the lab-on-paper device, the WO₃/BiVO₄ heterojunction was in situ grown onto the surface of cellulose fibers assisted with Au nanoparticle (Au NP) functionalization for enhancing the conductivity of the working zone of the device. With the target concentration increased, more immune conjugates could be captured by the proposed paper photoelectrode, which could lead to a quantitative decrease in the photocurrent intensity, eventually realizing the accurate PEC signal readout. To meet the requirement of end-user application, a colorimetric signal readout system was designed for the lab-on-paper device based on the color reaction of 3,3'5,5'-tetramethylbenzidine (TMB) oxidized by WO₃/BiVO₄ nanoflowers in the presence of H₂O₂. Noticeably, it is the first time that the WO₃/BiVO₄ heterojunction is in situ grown onto cellulose fibers, which enhances the sensitivity in view of both their PEC activity and catalytic ability. By controlling the conversion process of hydrophobicity and hydrophilicity on the lab-on-paper device combined with diverse origami methods, the dual-mode PEC/colorimetric signal output for the ultrasensitive AFP detection was realized. Under optimal conditions, the proposed dual-mode lab-on-paper device could enable the sensitive PEC/colorimetric diagnosis of AFP in the linear range of 0.09-100 ng mL^-1 and 5-100 ng mL^-1 with the limit of detection of 0.03 and 1.47 ng mL^-1, respectively.

Quantum dots for electrochemiluminescence bioanalysis - A review

Electrochemiluminescence (ECL) bioanalysis has become increasingly important in various fields from bioanalysis to clinical diagnosis due to its outstanding merits, including low background signal, high sensitivity, and simple instrumentation. Quantum dots (QDs) are a significant theme in ECL bioanalysis since their excellent optical, electrochemical properties, and ease of functionalization endow them with versatile roles and new mechanisms of signal transduction in ECL. Herein, this review details recent advances of QDs-based ECL bioanalysis by using QDs as ECL emitters, coreactants, or ECL resonance energy transfer donors/acceptors, mainly focused on their optical and electrochemical properties and ECL reaction mechanism. In the end, we will discuss the current limitations and future developments in QDs ECL bioanalysis to address the requirement about selectivity, sensitivity, toxicity, and emerging applications.

Graphene-Based Electrochemical Sensor for Detection of Hepatocellular Carcinoma Markers

Hepatocellular carcinoma (HCC) is a group of highly lethal malignant tumors that seriously threaten human health. The main way to improve the survival quality and reduce the mortality of HCC is early diagnosis and treatment. Therefore, it will be of great significance to explore new quantitative detection methods for HCC markers. With the rapid development of electrochemical biosensors and nanomaterials, electrochemical sensors based on graphene can detect tumor markers, with the advantages of simple operation, high detection sensitivity, and specificity. Combined with the published literature in recent years, the article briefly reviews the application of graphene-based electrochemical biosensors in the detection of HCC markers, including alpha-fetoprotein (AFP), Golgi protein-73 (GP73), exosomes, and microRNA-122 (miR-122).

Cytotoxicity and transcriptome changes triggered by CuInS2/ZnS quantum dots in human glial cells

As a newly developed cadmium-free quantum dot (QD), CuInS₂/ZnS has great application potential in many fields, but its biological safety has not been fully understood. In this study, the in vitro toxicity of CuInS₂/ZnS QDs on U87 human glioma cell line was explored. The cells were treated with different concentrations of QDs (12.5, 25, 50 and 100 μg/mL), and the uptake of QDs by the U87 cells was detected by fluorescence imaging and flow cytometry. The cell viability was observed by MTT assay, and the gene expression profile was analyzed by transcriptome sequencing. These results showed that QDs could enter the cells and mainly located in the cytoplasm. The uptake rate was over 90 % when the concentration of QDs reached 25 μg/mL. The cell viability (50 and 100 μg/mL) increased at 24 h (P < 0.05), but no significant difference after 48 h and 72 h treatment. The results of differential transcription showed that coding RNA accounted for the largest proportion (62.15 %), followed by long non-coding RNA (18.65 %). Total 220 genes were up-regulated and 1515 genes were down-regulated, and significantly altered gene functions included nucleosome, chromosome-DNA binding, and chromosome assembly. In conclusion, CuInS₂/ZnS QDs could enter U87 cells, did not reduce the cell viability, but would obviously alter the gene expression profile. These findings provide valuable information for a proper understanding of the toxicity risk of CuInS₂/ZnS QD and promote the rational utilization of QDs in the future.

Deoxynivalenol-induced cell apoptosis monitoring using a cytochrome c-specific fluorescent probe based on a photoinduced electron transfer reaction

Deoxynivalenol (DON) is considered a mycotoxin that is toxic to the agricultural environment and human body. It is necessary to study the pathophysiological mechanism of DON toxicity at the cellular level. Cytochrome c (Cyt c), as an important biomarker of DON-induced apoptosis that may lead to a bipartite 'point-of-no return' event, is of great significance to be detected using cell imaging. Herein, we synthesized a DON-deactivated emission fluorescent probe, the molecularly imprinted polymer-coated quantum dots (CdTe@MIP), for monitoring the Cyt c level with a photoinduced electron transfer strategy. The CdTe@MIP probe can be easily loaded into cells and perform well due to its great sensitivity and selectivity and its fluorescence was gradually quenched with the increasing concentration (0-10 μM) and incubation time (0-7.5 h) of DON. Cell imaging results of apoptosis induced by DON was consistent with that of the cell counting kit-8 assay and flow cytometry technique. The developed method can be used to monitor DON-induced apoptosis and provide an early-warning system for the contaminant toxicity.

Detection of Hg2+ by a Dual-Fluorescence Ratio Probe Constructed with Rare-Earth-Element-Doped Cadmium Telluride Quantum Dots and Fluorescent Carbon Dots

Quantum dots (QDs) and carbon quantum dots (CDs) are classes of zero-dimensional materials whose sizes can be ≤10 nm. They exhibit excellent optical properties and are widely used to prepare fluorescent probes for qualitative and quantitative detection of test objects. In this article, we used cerium chloride as the cerium source and used the in situ doped cerium (rare-earth element) to develop cadmium telluride (CdTe) quantum dots following the aqueous phase method. CdTe: Ce quantum dots were successfully synthesized. The solution of CdTe:Ce QDs was mixed with the CD solution prepared following the green microwave method to form a ratio fluorescence sensor that can be potentially used for the selective detection of mercury ions (Hg²⁺). We used transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and other microscopy and spectral characterization techniques to validate that Ce had been successfully doped. The test results on the fluorescence performance revealed that Ce doping enhances the predoped fluorescence performance of the CdTe QDs. We have quantitatively detected Hg²⁺ using a ratiometric fluorescence sensor to show that in the range of 10-60 nM, the fluorescence quenching efficiency increases linearly with the increase in Hg²⁺ concentration. The linear correlation coefficient R ² = 0.9978, and its detection limit was found to be 2.63 nM L^-1. It was observed that other interfering ions do not significantly affect the fluorescence intensity of the probe. According to the results of the blank addition experiment, the developed proportional fluorescence probe can be used for the detection of Hg²⁺ in actual samples.

A smartphone-integrated ratiometric fluorescence sensor for visual detection of cadmium ions

A novel fluorescence sensing platform was fabricated for visual detection of cadmium ions (Cd²⁺) with excellent stability and portability. In this protocol, dual-emission ratiometric fluorescence probe were constructed based on silicon oxide-coated copper nanoclusters (CuNCs@SiO₂) as a signal reference and cadmium telluride quantum dots (CdTe QDs) as signal response, thereby greatly improving the accuracy of test results. The level of Cd²⁺ can be reported within a wide linear range from 0.010 mg·L^-1 to 2.0 mg·L^-1 with a sensitive detection limit of 1.1 μg·L^-1 (2.75 μg·kg^-1) and a quick sample-to-answer monitoring time of 6 min, which was quite qualified for regularly monitoring Cd²⁺. Moreover, aiming to attain portable analysis, the smartphone as colorimetric reader and analyzer were also utilized for rapidly analyzing Cd²⁺ by capturing the change in fluorescence color. Additionally, benefiting from the strong combination of 1, 10-phenanthroline (Phen) and Cd²⁺, the fluorescence probe showed excellent anti-interference activities for Cd²⁺ assay in complex oyster matrix. Overall, the sensing platform had significant stability, specificity and sensitivity, offering a promising potential for conveniently evaluating the quality of marine bivalves polluted with Cd²⁺.

Ultrasensitive detection of cyclin D1 by a self-enhanced ECL immunosensor based on Bi2S3 quantum dots

Bismuth sulfide quantum dots (Bi₂S₃ QDs), which have excellent optical and thermoelectric properties, represent a green and non-toxic semiconductor material that has been widely used in catalysis and photoelectric conversion devices. At present, research on this material has gradually expanded into the biological field. Herein, the biomineralization method mediated by bovine serum albumin (BSA) was utilized to synthesize Bi₂S₃ QDs with monodispersity, excellent colloidal stability, and good biocompatibility. This is the first study on the electrochemiluminescence (ECL) characteristics of Bi₂S₃ QDs and related ECL mechanisms in detail. In addition, on the basis of Bi₂S₃ QDs, an ECL immunosensor was used for the ultrasensitive measurement of cyclin D1 (CCND1). The composite material, namely Au@Cu-Bi₂S₃ QDs was used as a high-sensitivity ECL probe, in which AuNPs were connected with Bi₂S₃ QDs through a copper(ii) ion bridge. PDA-AgNPs made of dopamine (DA) and silver nanoparticles (AgNPs) were utilized as a carrier for fixing the primary antibody (Ab₁), ultimately presenting a relatively wide detection range of 10 fg mL^-1-1 μg mL^-1. Moreover, quite a low detection limit (6.34 fg mL^-1) was also obtained for an assay of CCND1. Results indicated that the immunosensor can provide a potential platform with fine stability and creditable reproducibility for clinical diagnosis.

Facile Preparation of WO3-x Dots with Remarkably Low Toxicity and Uncompromised Activity as Co-reactants for Clinical Diagnosis by Electrochemiluminescence

The exceptional nature of WO_3-x dots has inspired widespread interest, but it is still a significant challenge to synthesize high-quality WO_3-x dots without using unstable reactants, expensive equipment, and complex synthetic processes. Herein, the synthesis of ligand-free WO_3-x dots is reported that are highly dispersible and rich in oxygen vacancies by a simple but straightforward exfoliation of bulk WS₂ and a mild follow-up chemical conversion. Surprisingly, the WO_3-x dots emerged as co-reactants for the electrochemiluminescence (ECL) of Ru(bpy)₃ ²⁺ with a comparable ECL efficiency to the well-known Ru(bpy)₃ ²⁺ /tripropylamine (TPrA) system. Moreover, compared to TPrA, whose toxicity remains a critical issue of concern, the WO_3-x dots were ca. 300-fold less toxic. The potency of WO_3-x dots was further explored in the detection of circulating tumor cells (CTCs) with the most competitive limit of detection so far.

A ratiometric electrochemiluminescence method using a single luminophore of porous g-C3N4 for the ultrasensitive determination of alpha fetoprotein

In this work, we report a simple ratiometric electrochemiluminescence method for ultra-sensitive immunoanalysis.

Structural, luminescence and geno/cytoxicity study of carbon dots derived from Opuntia ficus-indica (L.) Mill

Carbon dots derived from nopal significantly increase the number of micronuclei in mouse erythrocytes and inhibit mouse bone marrow cell proliferation.

A simple chemiluminescent aptasensor for the detection of α-fetoprotein based on iron-based metal organic frameworks

MIL-100 (Fe) was used to construct a chemiluminescent aptasensing platform based on the electrostatic adsorption of MIL-100 (Fe) and aptamers.

Sandwich-type electrochemical immunosensor for carcinoembryonic antigen detection based on the cooperation of a gold-vertical graphene electrode and gold@silica-methylene blue

In this study, a sandwich-type electrochemical (EC) immunosensor was proposed to detect a carcinoembryonic antigen (CEA) based on Au-graphene and Au@SiO₂-methylene blue (MB). The Au nanoparticles (NPs)-vertical graphene (VG) electrode efficiently amplifies the response signal by immobilizing a large amount of the coating antibody (Ab) and is characterized by excellent electrocatalytic activity. The MB nanodot-loaded Au@SiO₂ carriers with core-shell nanostructure and detection Ab were used to construct the Ab-Au@SiO₂-MB label, which improved the sensitivity due to the high EC signal of MB nanodots and the high labeling effect between the detection Ab and MB probe. A novel double-Ab sandwich strategy was developed to further improve the sensitivity and stability based on the same specificity of the coating and detection Abs for the recognition of CEA. Under optimal conditions, the developed EC sensor exhibited a wide linear range from 1 fg mL^-1 to 100 ng mL^-1, with an ultralow detection limit of 0.8 fg mL^-1 (S/N = 3). The feasibility in the clinical application of the EC sensor was verified by the in vitro detection of CEA in human serum.

Bioactivity-Protected Electrochemiluminescence Biosensor Using Gold Nanoclusters as the Low-Potential Luminophor and Cu2S Snowflake as Co-reaction Accelerator for Procalcitonin Analysis

The expansion of electrochemiluminescence (ECL) technology to immunoassay at the core of care emphasizes all immune molecules will not be inactivated in the analysis process. That poses a major challenge to ECL-based biosensors due to the deoxynucleotide sequences of an antigen or antibody could be oxidized through a route of excessive cyclic potential. Herein, an ultrasensitive ECL biosensor was developed based on a novel bioactivity-protected sensing strategy utilizing Au nanoclusters (Au NCs) as low-potential luminophor for detection of procalcitonin (PCT). Bovine serum albumin (BSA)-templated Au NCs exhibited a low-potential anodic ECL signal in triethylamine (TEA) solution at 0.87 V, where it is suitable for the survival of immune molecules. Taking advantage of good conductivity and high surface area, a Cu₂S snowflake not only functions as a satisfying substrate for connecting immune molecules but also acts as co-reaction accelerator to produce more cationic radicals TEA^•+, which could improve the ECL intensity needed to meet the requirements of trace analysis. Otherwise, HWRGWVC (HC-7) heptapeptide as specific antibody immobilizer for site-oriented fixation was introduced to further maintain the bioactivity of an antibody. In view of the preceding discussion, the obtained biosensor exhibited ultrahigh immune recognition to targets so that the detection limit was as low as an unprecedented value of 2.36 fg/mL, which will be of great significance to the application and development of a biosensor in the future.