Synthesis and characterization of a novel cellulose-g-poly(acrylic acid-co-acrylamide) superabsorbent composite based on flax yarn waste

Preparation of superabsorbent composite(s) based on dialdehyde cellulose extracted from banana fiber waste

The study focus is the valorization of banana agriculture by products by the extraction and derivatization of cellulose and its incorporation in formulations to produce superabsorbent materials endowed with high water absorption performances. The extracted cellulose (BP) was subjected to a controlled oxidation by sodium periodate to convert it to cellulose dialdehyde (DAC) with controlled aldehyde content. The cellulosic materials were incorporated into a suspension containing acrylic acid (AA) and itaconic acid (IA) to produce composite hybrid hydrogels (SA-BP/SA-DAC) by radical chain polymerization in water, using N,N-methylene-bis-acrylamide (MBA) as a cross-linking agent and potassium persulfate (KPS) as an initiator. The prepared materials were characterized using techniques such as Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and rheological analysis. Additionally, the absorption and re-swelling capacities of the superabsorbent composites (SAPs) were assessed through kinetic studies in water and NaCl solution. Notably, dialdehyde cellulose (DAC), due to its low crystallinity index, hydrophilicity (attributed to aldehyde and hemiacetal functions), and high polarity, holds promise for enhancing the swelling and water retention capacity of the hydrogel. A water absorption capacity as high as 1240±60 g.g-1 was obtained for SA-DAC with a DAC content of 5 %wt. Additionally, the reusability of the SAPs was evidenced.

Recent Advances in Superabsorbent Hydrogels Derived from Agro Waste Materials for Sustainable Agriculture: A Review

Superabsorbent hydrogels made from agro waste materials have the potential to promote sustainable agriculture and environmental sustainability. These hydrogels not only help reduce water consumption and increase crop yields but also contribute to minimizing waste and lowering greenhouse gas emissions. Recent research on superabsorbent hydrogels derived from agro wastes has focused on the preparation of hydrogels based on natural polymers isolated from agro wastes, such as cellulose, hemicellulose, and lignin. This review provides an in-depth examination of hydrogels developed from raw agro waste materials and natural polymers extracted from agro wastes, highlighting that these studies start with raw wastes as the main materials. The utilization strategies for specific types of agro wastes are comprehensively described. This review outlines different methods utilized in the production of these hydrogels, including physical cross-linking techniques such as dissolution-regeneration and freeze-thawing, as well as chemical cross-linking methods involving various cross-linking agents and graft polymerization techniques such as free radical polymerization, microwave-assisted polymerization, and γ radiation graft polymerization. Specifically, this review explores the applications of agro waste-based superabsorbent hydrogels in enhancing soil properties such as water retention and slow-release of fertilizers for sustainable agriculture.

Effect of chain structures of monomer on hydroxyethyl cellulose-based superabsorbent properties and improvement of chickpeas plant growth of water deficit-stressed

The aim of this research was evaluation of the influence of distance between zwitterionic monomer ions on the performance of superabsorbents. For this purpose, two zwitterionic monomers 4-(3-aminopropyl) amino-4-oxo-2-butenoic acid (APOB) and 4-(6-aminohexyl) amino-4-oxo-2-butenoic acid (AHOB) were prepared and applied for synthesis of two new superabsorbents through graft copolymerization onto hydroxyethyl cellulose (HEC) in the presence of acrylic acid (AA). In synthesis of superabsorbents factors such as the highest water absorbency capacity, absorbency rate, gel strength, and environmental problems should be resolved or improved. The results demonstrated that the water absorbency capacity and rate parameters (τ) of HEC-g-p(AA-co-APOB) and HEC-g-p(AA-co-AHOB) in distilled water were 986.62, 664.38 g/g, and 98.04, 140.84 min, respectively. The biodegradability of HEC-g-p(AA-co-APOB) was approximately 4 times more than HEC-g-p(AA-co-AHOB). However, based on the rheological analyses (G'/G″) HEC-g-p(AA-co-AHOB) was stronger than the other. Additionally, studies of water retention on soil containing HEC-g-p(AA-co-AHOB) superabsorbent (soil with 0.25 wt% material) showed that the after 30 days has ≤5 % water while soil in the absence of superabsorbent after 10 days completely dried. Studies of the growth of plants in soil demonstrated in the presence of HEC-g-p(AA-co-AHOB) the average length of shoots was 36 cm while without superabsorbent were 25 cm.

Advancements in Cellulose-Based Superabsorbent Hydrogels: Sustainable Solutions across Industries

The development of superabsorbent hydrogels is experiencing a transformative era across industries. While traditional synthetic hydrogels have found broad utility, their non-biodegradable nature has raised environmental concerns, driving the search for eco-friendlier alternatives. Cellulose-based superabsorbents, derived from sustainable sources, are gaining prominence. Innovations include biodegradable polymer hydrogels, natural cellulose-chitosan variants, and cassava starch-based alternatives. These materials are reshaping agriculture by enhancing soil fertility and water retention, serving as potent hemostatic agents in medicine, contributing to pollution control, and providing eco-friendly construction materials. Cellulose-based hydrogels also offer promise in drug delivery and hygiene products. Advanced characterization techniques aid in optimizing their properties, while the shift towards circular economy practices further highlights sustainability. This manuscript provides a comprehensive overview of these advancements, highlighting their diverse applications and environmental benefits.

Cellulose-Based Metallogels-Part 2: Physico-Chemical Properties and Biological Stability

Metallogels represent a class of composite materials in which a metal can be a part of the gel network as a coordinated ion, act as a cross-linker, or be incorporated as metal nanoparticles in the gel matrix. Cellulose is a natural polymer that has a set of beneficial ecological, economic, and other properties that make it sustainable: wide availability, renewability of raw materials, low-cost, biocompatibility, and biodegradability. That is why metallogels based on cellulose hydrogels and additionally enriched with new properties delivered by metals offer exciting opportunities for advanced biomaterials. Cellulosic metallogels can be either transparent or opaque, which is determined by the nature of the raw materials for the hydrogel and the metal content in the metallogel. They also exhibit a variety of colors depending on the type of metal or its compounds. Due to the introduction of metals, the mechanical strength, thermal stability, and swelling ability of cellulosic materials are improved; however, in certain conditions, metal nanoparticles can deteriorate these characteristics. The embedding of metal into the hydrogel generally does not alter the supramolecular structure of the cellulose matrix, but the crystallinity index changes after decoration with metal particles. Metallogels containing silver (0), gold (0), and Zn(II) reveal antimicrobial and antiviral properties; in some cases, promotion of cell activity and proliferation are reported. The pore system of cellulose-based metallogels allows for a prolonged biocidal effect. Thus, the incorporation of metals into cellulose-based gels introduces unique properties and functionalities of this material.

Synthesis of carboxymethyl cellulose-g-poly (acrylic acid-co-acrylamide)/polyvinyl alcohol sponge as a fast absorbent composite and its application in coral sand soil

To improve the rapid absorption capacity of coral sand soil for rainfall, a composite of carboxymethyl cellulose-g-poly (acrylic acid-co-acrylamide)/polyvinyl alcohol sponge (CMC-g-P(AA-co-AM)/PVA) was designed and synthesized by coupling CMC-g-P(AA-co-AM) granules with a PVA sponge. The results showed that the rapid water absorption of CMC-g-P (AA-co-AM)/PVA in distilled water in 1 h was 26.45 g/g, twice that of CMC-g-P(AA-co-AM) and the PVA sponge, which is suitable for short-term rainfall. In addition, the cation had a slight influence on the water absorption capacity of CMC-g-P (AA-co-AM)/PVA, which were 29.5 and 18.9 g/g in 0.9 wt% NaCl and CaCl₂ solutions, respectively, indicating the great adaptability of CMC-g-P (AA-co-AM)/PVA to high‑calcium coral sand. With the addition of 2 wt% CMC-g-P (AA-co-AM)/PVA, the water interception ratio of the coral sand increased from 13.8 % to 23.7 %, and 54.6 % of the total interception water remained after 15-day evaporation. Moreover, pot experiments demonstrated that 2 wt% CMC-g-P(AA-co-AM)/PVA in coral sand enhanced plant development under water scarcity, suggesting that CMC-g-P (AA-co-AM)/PVA is a promising soil amendment for coral sand soils.

Synthesis and property of superabsorbent polymer based on cellulose grafted 2-acrylamido-2-methyl-1-propanesulfonic acid

An eco-friendly superabsorbent polymer (SAP) was prepared by grafting 2-acrylamido-2-methyl-1-propanesulfonic acid onto microcrystalline cellulose in lithium chloride/N, N-dimethylacetamide system. The synthesized SAP (cellulose-g-PAMPS) was characterized by FTIR, TGA, SEM, ¹H NMR, ¹³C NMR and XRD. The water absorption equilibrium of cellulose-g-PAMPS could be achieved within 10 min in distilled water. Moreover, the maximum water absorption capacities of cellulose-g-PAMPS in distilled water, 0.9 wt% NaCl solution and 3.2 wt% Na₂CO₃ solution were 648.9, 298.4 and 207.3 g·g^-1, respectively. The water absorption behavior of cellulose-g-PAMPS was interpreted by the pseudo-second-order model. Furthermore, cellulose-g-PAMPS could be used in some extreme conditions due to its high acid and alkali resistance. The water retention rate of cellulose-g-PAMPS could be maintained above 90 % at 25 °C for 6 h. As a consequence, the synthesized SAP can be applied to increase the plant growth and survival time under drought conditions, even under saline alkali conditions.

Maleic acid as an important monomer in synthesis of stimuli-responsive poly(acrylic acid-co-acrylamide-co-maleic acid) superabsorbent polymer

Poly(acrylic acid-co-acrylamide-co-maleic acid) (p(AA-co-AM-co-MA)) superabsorbent polymer was synthesized from acrylic acid (AA), acrylamide (AM), and maleic acid (MA) via free radical copolymerization. Results showed the presence of maleic acid in structure of superabsorbent has the key and superior role in creating a smart superabsorbent. The structure, morphology, and strength of the superabsorbent were characterized using FT-IR, TGA, SEM, and rheology analysis. The effect of different factors was investigated to determine the ability of water absorbency of the superabsorbent. According to optimized conditions, the water absorbency capacity of the superabsorbent in distilled water (DW) was 1348 g/g and in a solution containing 1.0 wt.% NaCl (SCS) was 106 g/g. The water retention ability of the superabsorbent was also investigated. The kinetic swelling of superabsorbent was identified by Fickian diffusion and Schott's pseudo-second-order model. Furthermore, the reusability of superabsorbent was studied in distilled water and saline solution. The ability of superabsorbent was investigated in simulated urea and glucose solutions, and very good results were obtained. The response ability of the superabsorbent was confirmed by swelling and shrinking behavior against changes of temperature, pH, and ionic strength.

Cellulose/nanocellulose superabsorbent hydrogels as a sustainable platform for materials applications: A mini-review and perspective

Superabsorbent hydrogels (SAH) are crosslinked three-dimensional networks distinguished by their super capacity to stabilize a large quantity of water without dissolving. Such behavior enables them to engage in various applications. Cellulose and its derived nanocellulose can become SAHs as an appealing, versatile, and sustainable platform because of abundance, biodegradability, and renewability compared to petroleum-based materials. In this review, a synthetic strategy that reflects starting cellulosic resources to their associated synthons, crosslinking types, and synthetic controlling factors was highlighted. Representative examples of cellulose and nanocellulose SAH and an in-depth discussion of structure-absorption relationships were listed. Finally, various applications of cellulose and nanocellulose SAH, challenges and existing problems, and proposed future research pathways were listed.

Superabsorbent Polymers as a Soil Amendment for Increasing Agriculture Production with Reducing Water Losses under Water Stress Condition

With an increasing population, world agriculture is facing many challenges, such as climate change, urbanization, the use of natural resources in a sustainable manner, runoff losses, and the accumulation of pesticides and fertilizers. The global water shortage is a crisis for agriculture, because drought is one of the natural disasters that affect the farmers as well as their country's social, economic, and environmental status. The application of soil amendments is a strategy to mitigate the adverse impact of drought stress. The development of agronomic strategies enabling the reduction in drought stress in cultivated crops is, therefore, a crucial priority. Superabsorbent polymers (SAPs) can be used as an amendment for soil health improvement, ultimately improving water holding capacity and plant available water. These are eco-friendly and non-toxic materials, which have incredible water absorption ability and water holding capacity in the soil because of their unique biochemical and structural properties. Polymers can retain water more than their weight in water and achieve approximately 95% water release. SAP improve the soil like porosity (0.26-6.91%), water holding capacity (5.68-17.90%), and reduce nitrogen leaching losses from soil by up to 45%. This review focuses on the economic assessment of the adoption of superabsorbent polymers and brings out the discrepancies associated with the influence of SAPs application in the context of different textured soil, presence of drought, and their adoption by farmers.

A field study on using soybean waste-derived superabsorbent hydrogel to enhance growth of vegetables

Food security is critical and has become a global concern with many of our basic food crops growing in areas with high drought risk. To improve soil water holding capacity, hydrogels are a promising solution. However, the current ones are mostly derived from petroleum products and are environmental unsustainable. In this study, the main objective is to determine if bio-based hydrogel can help in the growth of leafy vegetables while minimizing water use under field conditions. To achieve this, we developed an okara-derived hydrogel (Ok-PAA; OP) from by-products of bean curd and soybean milk production. We incorporated OP into soil and assessed the growth performance of leafy vegetables. We observed that vegetables grown with 0.2% (w/v) OP in soil with a watering frequency of 7 times per week resulted in >60 % and 35 % yield increase for the common Asian leafy vegetables, choy sum (CS) and pak choi (PC), respectively, as compared to without hydrogel supplementation. Both vegetables produced larger leaf areas (20-40 % increment) in the presence of the hydrogel as compared to those without. In addition, with OP amendment, the irrigation water use efficiency improved >60 % and 30 % for CS and PC, respectively. It is estimated that with the use of the hydrogel, a reduction in watering frequency from 21 times to 7 times per week could be achieved, and based on a per hectare estimation, this would result in 196,000 L of water saving per crop cycle. Statistical analysis and modelling further confirmed vegetables grown with 0.2 % (w/v) OP and with a watering frequency of 7 times per week showed the best growth performance and water use efficiency. Such a waste-to-resource approach offers a plant-based soil supplement for crop growers, contributes to waste valorization, and enhances the growth of plants especially under water-limited conditions.

Surface ion-imprinted brewer's spent grain with low template loading for selective uranyl ions adsorption from simulated wastewater

Efficient removal of uranyl ions from wastewater requires excellent selectivity of the adsorbents. Herein, we report a new strategy using a high monomer/template molar ratio of 500:1 to prepare surface ion-imprinted brewer's spent grain (IIP-BSG) for selective U(VI) removal using binary functional monomers (2-hydroxyethyl methacrylate and diethyl vinylphosphonate) with high site accessibility and easy template removal. IIP-BSG exhibits a maximum U(VI) adsorption capacity of 165.7 mg/g, a high selectivity toward U(VI) in the presence of an excess amount of Eu(III) (Eu/U molar ratio = 20), a good tolerance of salinity, and a high reusability. In addition, mechanism studies have revealed electrostatic interaction and a coordination of uranyl ions by carboxyl and phosphoryl groups, the predominant contribution of high-energy (specific) sites during selective adsorption, and internal mass transfer as the rate-controlling step of U(VI) adsorption. Furthermore, IIP-BSG shows great potentials to separate U(VI) from lanthanides in simulated nuclear wastewater (pH₀ = 3.5) and selectively concentrate U(VI) from simulated mine water (pH₀ = 7.1). This study proves that the ion-imprinting effect can be achieved using a very low template amount with reduced production cost and secondary pollution, which benefits large-scale promotion of the ion-imprinted materials for selective uranyl ions removal.

One-pot synthesis of brewer's spent grain-supported superabsorbent polymer for highly efficient uranium adsorption from wastewater

High-efficient and fast adsorption of uranium is important to reduce the hazards caused by the uranium contamination of water environment due to the increased human activities. Herein, brewer's spent grain (BSG)-supported superabsorbent polymers (SAP) with different cross-linking densities are prepared as cheap and eco-friendly adsorbents for the first time via one-pot swelling and graft polymerization. A 7 wt% NaOH solution is used to swell BSG before grafting and subsequently neutralize the acrylic acid to control the reaction rate without producing alkaline wastewater. Compared with the traditional methods, swelling improves the grafting density and the utilization of raw materials due to the increased disorder degree of the BSG fibers. This results in the grafting of abundant carboxyl and amide groups onto the BSG backbone, forming a strongly hydrophilic polymer network of the BSG-SAP. Compared with the reference polymers without BSG, BSG-SAP presents higher adsorption capacity and enhanced reusability. The highly cross-linked BSG-SAP (BSG-SAP-H) shows an outstanding adsorption capacity of U(VI) (1465 mg/g at pH₀ = 4.6), a fast adsorption rate (81% of equilibrium adsorption capacity in 15 min), and a high selectivity in the presence of competing ions. Adsorption mechanism studies reveal the involvement of amide groups, a bidentate binding structure between UO₂²⁺ and the carboxyl groups, and a cation exchange between Na⁺ and UO₂²⁺. More importantly, the adsorption capacity of BSG-SAP-H reaches 254.4 mg/g in the fixed-bed column experiment at a low initial concentration (c₀(U) = 30 mg/L) and keeps 80% of the adsorption capacity after four cycles, indicating a great potential for uranium removal from wastewater. This work shows a suitable approach to explore the untreated biomass to prepare SAP with enhanced adsorption performance via a general and low-cost strategy.

Degradation of Hydrogels Based on Potassium and Sodium Polyacrylate by Ionic Interaction and Its Influence on Water

Hydrogels are a very useful type of polymeric material in several economic sectors, acquiring great importance due to their potential applications; however, this type of material, similarly to all polymers, is susceptible to degradation, which must be studied to improve its use. In this sense, the present work shows the degradation phenomena of commercial hydrogels based on potassium and sodium polyacrylate caused by the intrinsic content of different types of potable waters and aqueous solutions. In this way, a methodology for the analysis of this type of phenomenon is presented, facilitating the understanding of this type of degradation phenomenon. In this context, the hydrogels were characterized through swelling and FTIR to verify their performance and their structural changes. Likewise, the waters and wastewaters used for the swelling process were characterized by turbidity, pH, hardness, metals, total dissolved solids, electrical conductivity, DLS, Z-potential, and UV-vis to determine the changes generated in the types of waters caused by polymeric degradation and which are the most relevant variables in the degradation of the studied materials. The results obtained suggest a polymeric degradation reducing the swelling capacity and the useful life of the hydrogel; in addition, significant physicochemical changes such as the emergence of polymeric nanoparticles are observed in some types of analyzed waters.

Triblock Superabsorbent Polymer Nanocomposites with Enhanced Water Retention Capacities and Rheological Characteristics

Superabsorbent polymers (SAPs) are useful polymers in a wide range of application fields ranging from the hygiene industry to construction and agriculture. As versatility and high water absorption capacity are their important merits, SAPs usually suffer from low water retention capacity (fast release) and weak mechanical properties. To address these drawbacks, a set of new superabsorbent polymer-Halloysite nanotube (HNT) nanocomposites was synthesized via free radical polymerization of acrylamide, 2-acrylamido-2-methylpropane-1-sulfonic acid, and acrylic acid in the presence of vinyltrimethoxysilane (VTMS) as the crosslinker. FTIR and TGA characterizations confirm the polymerization of SAP and successful incorporation of HNTs into the SAP polymer matrix. The effect of the HNT nanofiller amount in the nanocomposite polymer matrix was investigated with swelling-release performance tests, crosslink density calculations, and rheology measurements. It was found that equilibrium swelling ratios are correlated and therefore can be tuned via the crosslink densities of nanocomposites, while water retention capacities are governed by storage moduli. A maximum swelling of 537 g/g was observed when 5 wt % HNT was incorporated, in which the crosslink density is the lowest. Among the SAP nanocomposites prepared, the highest storage modulus was observed when 1 wt % of nanofiller was incorporated, which coincides with the nanocomposite with the longest water retention. The water release duration of SAPs was prolonged up to 27 days with 1% HNT addition in parallel with the achieved maximum storage modulus. Finally, three different incorporation mechanisms of the HNT nanofiller into the SAP nanocomposite structure were proposed and confirmed with rheology measurements. This study provides a rapid synthesis method for SAP nanocomposites with enhanced water retention capacities and explains the relationship between swelling and crosslink density and water retention and mechanical properties of SAP nanocomposites.

Preparation and Enzyme Degradability of Spherical and Water-Absorbent Gels from Sodium Carboxymethyl Cellulose

To synthesize a biodegradable alternative to spherical polyacrylic acid absorbent resin, spherical hydrogel particles were prepared from carboxymethyl cellulose (CMC) dissolved in an aqueous solution, using ethylene glycol diglycidyl ether (EGDE) as a crosslinking agent. The effect of varying the initial CMC concentration and feed amount of EGDE on the shape, water absorbency, water-holding capacity, and enzyme degradability of the resultant CMC hydrogels was determined. The reaction solution was poured into fluid paraffin, and spherical hydrogel particles were obtained via the shear force from stirring. The shape and diameter of the spherical hydrogel particles in the swollen state depended on the CMC concentration. The spherical hydrogel particles obtained by increasing the amount of EGDE resulted in a decrease in absorbency. Additionally, all the spherical hydrogel particles were degraded by cellulase. Thus, spherical biodegradable hydrogel particles were prepared from CMC, and the particle size and water absorption of the hydrogel could be controlled in the range of 5–18 mm and 30–90 g·g⁻¹ in the swollen state, respectively. As an alternative to conventional superabsorbent polymers, the spherical CMC hydrogels are likely to be useful in industrial and agricultural applications.

Free Radical Copolymerization of Diallylamine and Itaconic Acid for the Synthesis of Chitosan Base Superabsorbent

Copolymerization of diallylamine (DAA) and itaconic acid (IA) was synthesized using benzoyl peroxide as a free radical initiator, in dioxane as the solvent. The composition of the copolymer was determined by the nitrogen content using Edx. The solubility of the copolymer was also investigated. The water solubility of the synthesized copolymer depends on the comonomers’ ratio. The structure of the copolymer was confirmed by ¹³C-NMR spectroscopy. To increase the water insolubility of the copolymers, and keep their hydrophilicity, the copolymer was allowed to react with chitosan to form a superabsorbent polymeric material (SP). The structure of the synthesized superabsorbent was confirmed using ¹³C-NMR spectroscopy. The thermal property of the (SP) was also investigated by TGA. The investigation of the chitosan-based superabsorbent, as water-retaining agents, was studied. The results revealed that the superabsorbent polymers exhibited a good swelling ability and salt tolerance.

Novel Synthesis, Characterization and Amoxicillin Release Study of pH-Sensitive Nanosilica/Poly(acrylic acid) Macroporous Hydrogel with High Swelling

The effect of SiO₂ nanoparticles on the formation of PAA (poly acrylic acid) gel structure was investigated with seeded emulsion polymerization method used to prepare SiO₂/PAA nanoparticles. The morphologies of the nanocomposite nanoparticles were studied by transmission electron microscopy (TEM). Fourier-transform infrared (FTIR) spectroscopy results indicated that the PAA was chemically bonded to the surface of the SiO₂ nanoparticles. Additionally, the resulting morphology of the nanocomposite nanoparticles confirmed the co-crosslinking role of the SiO₂ nanoparticles in the formation of the 3D structure and hydrogel of PAA. SiO₂/PAA nanocomposite hydrogels were synthesized by in situ solution polymerization with and without toluene. The morphology studies by field emission scanning electron microscopy (FESEM) showed that when the toluene was used as a pore forming agent in the polymerization process, a macroporous hydrogel structure was achieved. The pH-sensitive swelling behaviors of the nanocomposite hydrogels showed that the formation of pores in the gels structure was a dominant factor on the water absorption capacity. In the current research the absorption capacity was changed from about 500 to 4000 g water/g dry hydrogel. Finally, the macroporous nanocomposite hydrogel sample was tested as an amoxicillin release system in buffer solutions with pHs of 3, 7.2, and 9 at 37 °C. The results showed that the percentage cumulative release of amoxicillin from the hydrogels was higher in neutral and basic mediums than in the acidic medium and the amoxicillin release rate was decreased with increasing pH. Additionally, the release results were very similar to swelling results and hence amoxicillin release was a swelling controlled-release system.

Synthesis of a novel superabsorbent with slow-release urea fertilizer using modified cellulose as a grafting agent and flexible copolymer

In this work, a number of glucose unites in polymeric structure of cellulose was converted to 2,4-dihydroxy-3-(1-hydroxy-2-oxoethoxy)butanal (cellulose containing di aldehyde units (CCDAUs)) by oxidation with sodium periodate, followed by condensation with acetone to produce 5,7-dihydroxy-6-((1-hydroxy-4-oxopent-2-en-1-yl)oxy)hept-3-en-2-one unites (cellulose containing di ene units (CCDEUs)). This modified cellulose was characterized by different methods and applied as a copolymer and grafting agent to synthesize an eco-friendly (CCDEUs-g-poly(AA)/urea) superabsorbent with slow-release urea fertilizer. The created double bonds in C₂ and C₃ positions of β-d-glucose units increased the linkage between cellulose and acrylic acid, leading to the formation of a strong network for slow-release urea fertilizer. Also, this modification created an expanded network for storage a high amount of water by increasing the cellulose flexibility. The reaction conditions for modification and synthesis of the superabsorbent, the oxidation degree value of glucose units, kinetics models, the effect of different saline solutions, various pH and reswelling time on the water absorbency, water retention capacity, reusability, biodegradability, and slow-release property were investigated. Also, the effect of synthesized CCDEUs-g-poly(AA)/urea on plant growth was tested and excellent results were obtained.

P. S. AK, Oyekanmi AA, Gideon ON, Abdullah CK, Yahya EB, Alfatah T, Sabaruddin FA, Rahman AA. Cotton Wastes Functionalized Biomaterials from Micro to Nano: A Cleaner Approach for a Sustainable Environmental Application

The exponential increase in textile cotton wastes generation and the ineffective processing mechanism to mitigate its environmental impact by developing functional materials with unique properties for geotechnical applications, wastewater, packaging, and biomedical engineering have become emerging global concerns among researchers. A comprehensive study of a processed cotton fibres isolation technique and their applications are highlighted in this review. Surface modification of cotton wastes fibre increases the adsorption of dyes and heavy metals removal from wastewater. Cotton wastes fibres have demonstrated high adsorption capacity for the removal of recalcitrant pollutants in wastewater. Cotton wastes fibres have found remarkable application in slope amendments, reinforcement of expansive soils and building materials, and a proven source for isolation of cellulose nanocrystals (CNCs). Several research work on the use of cotton waste for functional application rather than disposal has been done. However, no review study has discussed the potentials of cotton wastes from source (Micro-Nano) to application. This review critically analyses novel isolation techniques of CNC from cotton wastes with an in-depth study of a parameter variation effect on their yield. Different pretreatment techniques and efficiency were discussed. From the analysis, chemical pretreatment is considered the most efficient extraction of CNCs from cotton wastes. The pretreatment strategies can suffer variation in process conditions, resulting in distortion in the extracted cellulose's crystallinity. Acid hydrolysis using sulfuric acid is the most used extraction process for cotton wastes-based CNC. A combined pretreatment process, such as sonication and hydrolysis, increases the crystallinity of cotton-based CNCs. The improvement of the reinforced matrix interface of textile fibres is required for improved packaging and biomedical applications for the sustainability of cotton-based CNCs.

Synthesis and application of eco-friendly superabsorbent composites based on xanthan gum and semi-coke

An eco-friendly superabsorbent composites of xanthan gum-g-polyacrylic acid/semi-coke (XG-g-PAA/SC) were fabricated via grafting of polyacrylic acid onto the XG in the presence of SC. The obtained products were characterized in combination with Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). The result indicated that the SC interacted with the polymeric network by hydrogen bond or electrostatic interaction. The swelling ratio of the best sample XG-g-PAA/SC (15 wt%) in distilled water and 0.9 wt% NaCl solution was 410.8 and 61.5 g/g by optimizing the polymerization conditions. In addition, compared with the blank sample (only containing soil), it can be found that adding a certain amount of XG-g-PAA/SC can significantly improve the soil water retention efficiency, which can be further proved by the results of plant pot experiment. Based on the above excellent swelling capacity, water holding capacity and plant growth promoting performance, it can be inferred that the XG-g-PAA/SC is expected to become a water retaining agent or soil regulator for plant growth.

Transformation of non-water sorbing fly ash to a water sorbing material for drought management

Securing water in the soil through suitable amendments is one of the methods for drought management in arid regions. In this study, a poor water sorbing fly ash was transformed into a high water-absorbing material for improving soil water retention during the drought period. The fly ash water absorbent (FAWA) exhibited high water-absorbing capacity (WAC) of 310 g/g at par with commercially available superabsorbent hydrogel (SAH). The FAWA showed excellent re-swelling behavior for more than eight alternate wetting–drying cycles. The WAC of FAWA was sensitive to salt type, pH, and ionic strength of the solution. At maximum salinity level permitted for plant growth, the WAC of FAWA was 80 g/g indicating its suitability for drought management. There was only a marginal WAC variation in the range of pH (5.5–7.5) considered most suitable for plant growth. The drying characteristics of FAWA amended soil exhibited an increase in desaturation time by 3.3, 2.2, and 1.5 times for fine sand, silt loam, and clay loam, respectively. The study demonstrates the success of using a low rate of FAWA for drought management with the advantage of offering a non-toxic and eco-friendly solution to mass utilization of industrial solid waste for agricultural applications.

Superabsorbent Fibers for Comfortable Disposable Medical Protective Clothing

Disposable medical protective clothing for 2019-nCoV mainly consists of stacked layers with nanopore films, polymer coated nonwoven fabrics and melt-blown nonwoven fabrics against anti-microbial and anti-liquid penetration. However, such structures lack moisture permeability and breathability leading to an uncomfortable, stuffy wearing experience. Here, we propose a novel medical protective clothing material with a superabsorbent layer to enhance moisture absorption. Poly(acrylic acid-co-acrylamide)/polyvinyl alcohol superabsorbent fibers (PAAAM/PVA fibers) were prepared via wet spinning. And the superabsorbent composite layer was stacked from PAAAM/PVA fibers, bamboo pulp fibers (BPF) and ethylene-propylene side by side fibers (ESF). The novel disposable medical protective composite fabric was obtained through gluing the superabsorbent layer to the inner surface of strong antistatic polypropylene nonwoven fabric. The resultant composite fabric possesses excellent absorption and retention capacity for sweat, up to 12.3 g/g and 63.8%, and a maximum hygroscopic rate of 1.04 g/h, higher than that of the conventional material (only 0.53 g/h). The moisture permeability of the novel material reached 12,638.5 g/(m2 d), which was 307.6% of the conventional material. The novel material can effectively reduce the humidity inside the protective clothing and significantly improve the comfort of medical staff.

pH-Sensitive Hydrogel from Polyethylene Oxide and Acrylic acid by Gamma Radiation

Hydrogel as a good water absorbent has attracted great research interest. A series of hydrogel based on polyethylene oxide (PEO) and acrylic acid (AAc) was prepared by applying gamma radiation with variation in the concentration of acrylic acid. Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) were used to characterize the PEO/ AAc hydrogel. The properties of the prepared hydrogels such as gel content, swelling behavior, tensile strength, and pH sensitivity were evaluated. The formation of the hydrogels was confirmed from FTIR spectra. SEM images showed the inner porous structure of the hydrogels. The dose of gamma radiation was optimized to get a hydrogel with good swelling property and mechanical strength. The swelling ratio and gel content of the hydrogels were increased with increasing acrylic acid content. The pH of the solutions affected the swelling which indicated the pH-responsive property of the prepared hydrogels. Swelling of the prepared hydrogels in sodium chloride salt solutions decreased with increasing the ionic strength.

Biodegradable Poly(acrylic acid-co-acrylamide)/Poly(vinyl alcohol) Double Network Hydrogels with Tunable Mechanics and High Self-healing Performance

We proposed a novel strategy in the fabrication of biodegradable poly(acrylic acid-co-acrylamide)/poly(vinyl alcohol) (P(AAc-co-Am)/PVA) double network (DN) hydrogels with good mechanical and self-healing properties. In the DN hydrogel system, P(AAc-co-Am) polymers form a network through the ionic coordinates between -COO- and Fe3+ and hydrogen bonding between -COOH and -CONH2, while another network is fabricated by the complexation between PVA and borax. The influences of the composition on the rheological behaviors and mechanical properties of the synthesized DN hydrogels were investigated. The rheological measurements revealed that the viscoelasticity and stiffness of the P(AAc-co-Am)/PVA DN hydrogels increase as the acrylamide and Fe3+ concentrations increase. At 0.05 mmol of Fe3+ and 50% of acrylamide, tensile strength and elongation at break of P(AAc-co-Am)/PVA DN hydrogels could reach 329.5 KPa and 12.9 mm/mm, respectively. These properties arise from the dynamic reversible bonds existed in the P(AAc-co-Am)/PVA DN hydrogels. These reversible bonds also give good self-healing properties, and the maximum self-healing efficiency of P(AAc-co-Am)/PVA DN hydrogels is up to 96.4%. The degradation test of synthesized DN hydrogels was also conducted under simulated physiological conditions and the weight loss could reach 74% in the simulated intestinal fluid. According to the results presented here, the synthesized P(AAc-co-Am)/PVA DN hydrogels have a potential application prospect in various biomedical fields.

Synthesis of superabsorbent polymers based on chitosan derivative graft acrylic acid-co-acrylamide and its property testing

A new kind of eco-friendly superabsorbent polymer was successfully synthesized using (2-pyridyl) acetyl chitosan chloride (PACS), acrylic acid (AA) and acrylamide (AM) in aqueous solution by a free radical polymerization. The effect of different reaction conditions, such as the initiator content, crosslinker content and PACS content were investigated. And the water retention, salt tolerance and reuse ability were investigated too. The chemical structure and morphological characterizations of the superabsorbent polymer were investigated by Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), Thermogravimetric analysis (TGA) and Scanning electron microscope (SEM). The results showed that the novel superabsorbent polymer exhibits excellent water absorbency, which can absorb distilled water 615 g/g and 0.9% NaCl solution 44 g/g. At the same time, this product showed excellent water retention and reusability. The antibacterial properties of the superabsorbent polymers were tested too. The introduction of antibacterial groups also enhances antibacterial properties against Escherichia coli and Staphylococcus aureus. This kind of superabsorbent polymer has a broad application prospect.

Slow release fertilizer hydrogels: a review

Slow release fertilizer hydrogels combine fertilizer and hydrogel into one system.

Morphology and thermal properties of clay based biocomposites

Carboxymethylcellulose/poly(ethylene glycol) (CMC/PEG) blend and CMC/PEG/montmorillonite (MMT) nanocomposites were produced by the solvent casting method. The clay, a sodium MMT, was incorporated in the polymer matrix at low weight loadings (from 1 wt% to 7 wt%). The MMT dispersion in the matrix was evaluated by X-ray diffraction, which revealed an intercalated structure of the nanocomposites. Different levels of intercalation have been detected. The changes in morphology caused by the addition of layered silicate on CMC/PEG blend were investigated by scanning electron microscopy (SEM). The SEM images of CMC/PEG blend containing 5% of MMT displayed more homogenous morphology than CMC/PEG blend. The compatibilizing performance of the filler was investigated using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and Fourier transform infrared (FTIR) spectroscopy. The effect of the introduction of the clay on the crystallization temperature, melting temperature and crystallization degree of CMC/PEG revealed that clay behaved as a nucleating agent and enhanced the crystallization rate of PEG. Furthermore, it was demonstrated that the addition of a small percentage of montmorillonite (1%) was enough to improve the thermal stability of the nanocomposites.

Nanoscale Homogeneous Energetic Copper Azides@Porous Carbon Hybrid with Reduced Sensitivity and High Ignition Ability

Research on green primary explosives with lead-free and excellent ignition performance is of significance for practical applications. In this work, we have developed a novel, green, and facile strategy for synthesizing copper azide@porous carbon hybrids (CA@PC) based on ionic cross-linked hydrogel with low-cost cellulose derivatives as the starting material, in which the CA nanoparticles are uniformly distributed in the porous carbon skeletons. The detailed characterizations and control experiments demonstrated that such an outstanding performance originates from the excellent electric conductivity of nanoscale carbon cages. With the favorable unique structures, the as-prepared hybrids can greatly benefit a new type of energetic materials, which exhibit a very low electrostatic sensitivity of 1.06 mJ. Interestingly, the hybrids possess a high ignition ability, and the flame sensitivity can even achieve 47 cm, superior to those well-developed CA-based materials reported previously. This work paves the way toward the design and development of next-generation highly efficient energetic materials.

Cellulose-Based Absorbent Production from Bacterial Cellulose and Acrylic Acid: Synthesis and Performance

Cellulose-based superabsorbent was synthesized by bacterial cellulose (BC) grafting acrylic acid (AA) in the presence of N,N′-methylenebisacrylamide (NMBA) as a crosslinker and ammonium persulfate (APS) as an initiator. The influence of different factors on composite synthesis, including the weight ratio of the monomer to BC, initiator content, crosslinker content, AA neutralization degree, reaction temperature, and reaction time on the water absorbency of the composite, were systematically learned. Under the optimized conditions, the maximum water absorbency of the composite was 322 ± 23 g/g distilled water. However, the water absorbency was much less for the different salt solutions and the absorption capacity of the composite decreased as the concentration of the salt solutions increased. The pH value had a significant influence on water absorption performance, and with the increase of temperature, the water retention rate of the composite decreased. Additionally, the structure of this composite was characterized with nuclear magnetic resonance (NMR), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The results of NMR and FT-IR provided evidence that the composite was synthesized by BC and AA, and the microstructure showed that it had good performance for water absorption. In addition, the composite possessed suitable thermal stability, and that it could be used in a few high-temperature environments. Overall, this composite is promising for application in water absorption.