Preparation and characterization of crosslinked chitosan/gelatin scaffolds by ice segregation induced self-assembly

Effects of the green cross-linking agent tannic acid and its oxidation on the properties of porcine plasma protein superabsorbent materials

Tannic acid is a natural polyphenol capable of strongly interacting with proteins, with good antioxidant and antibacterial properties. Thus, tannic acid (TA) or oxidized tannic acid (oxTA) may be used as cross-linking agents in the development of reinforced and fully protein-based superabsorbent materials (SAMs). oxTA was produced so that reactive quinone groups were generated, which are expected to increase its reactivity. In this study, porcine plasma protein (PPP) and glycerol (gly) were used in a 50/50 PPP/gly ratio to obtain SAMs through twin screw mixing and injection molding. The results showed that both TA and oxTA increased the storage modulus and the loss tangent of blends and bioplastics due to the physical interactions established between TA or oxTA and PPP. The mechanical properties, particularly the Young's modulus and tensile strength, were generally enhanced as well. Water absorption was strongly influenced by the addition of TA, resulting in a decrease in the amount of water absorbed. However, samples containing oxTA resulted in a greater water absorption capacity, retaining a higher proportion of the superabsorbent properties of the reference composition. Moreover, systems containing oxTA generally possess better mechanical properties than those of equivalent TA formulations, especially those containing 5 % and 10 % oxTA.

Composite biopolymer foams fabricated from natural aldehyde functionalized chitosan-whey protein amyloid fibrils: Application for removal of phthalate esters from water

In this work, composite biopolymer foams from chitosan and whey isolate protein amyloid fibrils were prepared for the removal of phthalate esters from water. Natural aldehyde functionalization enhanced the affinity for dibutyl phthalate (DBP), with citral being the most effective. The citral-grafted foams (WCGC) had tunable hydrophobicity, strong mechanical properties, and good water stability. WCGC1.5 foam exhibited a high removal efficiency (96.06 %) of DBP. The adsorption process reached adsorption equilibrium rapidly within 8 h and could be described by pseudo-second-order kinetic and Freundlich isotherm models, indicating a non-homogeneous and chemisorptive sorption process. The maximum adsorption capacity for DBP reached 332.42 mg/g. Moreover, DBP adsorption could be enhanced in alkaline environment and the removal efficiency increased to 98.27 % at pH 10. The removal efficiency of DBP by WCGC1.5 remained above 85 % after the five adsorption-desorption cycles. WCGC1.5 also showed broad-spectrum adsorption behavior, with strong affinity and removal efficiency for six common plasticizers, including DIBP (85.97 %), DPP (91.7 %), DHXP (99.1 %), DEHP (99.09 %), DNOP (91.6 %) and BBP (89.88 %).

Fabrication of highly flexible biopolymeric chitosan/agarose based bioscaffold with Matricaria recutita herbal extract for antimicrobial wound dressing applications

A flexible biopolymer-based antimicrobial wound dressing has the potential to alleviate the burden of bacterial infections in wounds by enhancing antimicrobial effectiveness and promoting faster wound healing. This study focuses on the development of a highly flexible chitosan-agarose (CS-AG) bioscaffold, incorporating Matricaria recutita chamomile flower extract (CH) through a conventional casting method. The flexible CS-AG bioscaffold's physiochemical properties were confirmed by FTIR, indicating secondary interactions, and XRD, showing its crystalline structure. The addition of CH to the optimized CS-AG bioscaffold resulted in significant tensile strength (17.28 ± 0.33 MPa), distinctive structural morphology (SEM), surface roughness (AFM), contact angle, improved thermal properties (DSC), and enhanced thermal stability (TGA). Furthermore, the CH-infused bioscaffold significantly increased swelling capacity (~81.09 ± 1.74 % over 48 h), and degradation profile (~52 % over 180 h). The release studies of CS-AG-CH bioscaffold demonstrate controlled release of CH with in the bioscaffold at different pH conditions. The bioscaffold demonstrated effective antibacterial activity against S. aureus and E. coli strains. Additionally, cytotoxicity assays indicated that the bioscaffold supports better cell viability and proliferation in fibroblast (NIH 3T3) cell lines. Consequently, this antimicrobial bioscaffold shows promise as a drug release system and biocompatible wound dressing suitable for tissue engineering applications.

Gelatin-chitosan interactions in edible films and coatings doped with plant extracts for biopreservation of fresh tuna fish products: A review

The preservation of tuna fish products, which are extremely perishable seafood items, is a substantial challenge due to their instantaneous spoilage caused by microbial development and oxidative degradation. The current review explores the potential of employing chitosan-gelatin-based edible films and coatings, which are enriched with plant extracts, as a sustainable method to prolong the shelf life of tuna fish products. The article provides a comprehensive overview of the physicochemical properties of chitosan and gelatin, emphasizing the molecular interactions that underpin the formation and functionality of these biopolymer-based films and coatings. The synergistic effects of combining chitosan and gelatin are explored, particularly in terms of improving the mechanical strength, barrier properties, and bioactivity of the films. Furthermore, the application of botanical extracts, which include high levels of antioxidants and antibacterial compounds, is being investigated in terms of their capacity to augment the protective characteristics of the films. The study also emphasizes current advancements in utilizing these composite films and coatings for tuna fish products, with a specific focus on their effectiveness in preventing microbiological spoilage, decreasing lipid oxidation, and maintaining sensory qualities throughout storage. Moreover, the current investigation explores the molecular interactions associated with chitosan-gelatin packaging systems enriched with plant extracts, offering valuable insights for improving the design of edible films and coatings and suggesting future research directions to enhance their effectiveness in seafood preservation. Ultimately, the review underscores the potential of chitosan-gelatin-based films and coatings as a promising, eco-friendly alternative to conventional packaging methods, contributing to the sustainability of the seafood industry.

Tough gelatine hydrogels reinforced with silk fibroin nanofiber

Gelatine hydrogels exhibit potential as biomaterials such as wound-healing materials, artificial organs, scaffolds for cell culture and drug delivery systems because of their good biocompatibility. However, their practical applications are limited by their poor mechanical properties and high degradability. In this study, mechanically fibrillated silk fibroin (fibroin nanofibers; FNF) was used to reinforce gelatine hydrogels. The resulting gelatine hydrogels with FNF exhibited enhanced toughness compared to those reinforced with conventional aqueous regenerated fibroin (RF), which were prepared by treatment with a highly concentrated LiBr solvent or a neat gelatine hydrogel while retaining their softness. The average pore size of the gelatine hydrogel was 2.2 μm, while the gelatine hydrogel containing 25 % FNF expanded to 6.7 μm. A web-like network was formed between the pores. The addition of FNF increased the relative β-sheet contents in the hydrogels to 60.3 %, suggesting that this may have caused structural changes such as increased crystallinity for gelatine-derived proteins. Furthermore, the addition of FNF inhibited the rapid enzymatic degradation of gelatine hydrogels. FNF, which can be easily prepared in water, is a safe material for both the environment and living organisms and holds promise as a biomaterial in the future.

Fabrication, characterization, and oxidation resistance of gelatin/egg white protein cryogel-templated oleogels through apple polyphenol crosslinking

Cryogel-templated oleogels (CTO) were fabricated via a facile polyphenol crosslinking strategy, where apple polyphenol was utilized to crosslink the gelatin/egg white protein conjugates without forming hydrogels. After freeze-drying, cryogel templates were obtained and used to construct CTO by oil absorption. Apple polyphenol crosslinking improved the emulsion-related properties with appearance changes on samples, and infrared spectroscopy further confirmed the interactions between proteins and apple polyphenol. The crosslinked cryogels presented porous microstructures (porosity of over 96 %), enhanced thermal/mechanical stabilities, and could absorb a high content of oil (14.41 g/g) with a considerable oil holding capacity (90.98 %). Apple polyphenol crosslinking also influenced the rheological performances of CTO, where the highly crosslinked samples owned the best thixotropic recovery of 85.88 %. Moreover, after the rapid oxidation of oleogels, the generation of oxidation products was effectively inhibited by crosslinking (POV: 0.48 nmol/g, and TBARS: 0.53 mg/L). The polyphenol crosslinking strategy successfully involved egg white protein and gelatin to fabricate CTO with desired physical/chemical properties. Apple polyphenol acted as both a crosslinker and an antioxidant, which provided a good reference for fabricating pure protein-based CTO.

Design of Collagen and Gelatin-based Electrospun Fibers for Biomedical Purposes: An Overview

Collagen and gelatin are essential natural biopolymers commonly utilized in biomaterials and tissue engineering because of their excellent physicochemical and biocompatibility properties. They can be used either in combination with other biomacromolecules or particles or even exclusively for the enhancement of bone regeneration or for the development of biomimetic scaffolds. Collagen or gelatin derivatives can be transformed into nanofibrous materials with porous micro- or nanostructures and superior mechanical properties and biocompatibility using electrospinning technology. Specific attention was recently paid to electrospun mats of such biopolymers, due to their high ratio of surface area to volume, as well as their biocompatibility, biodegradability, and low immunogenicity. The fiber mats with submicro- and nanometer scale can replicate the extracellular matrix structure of human tissues and organs, making them highly suitable for use in tissue engineering due to their exceptional bioaffinity. The drawbacks may include rapid degradation and complete dissolution in aqueous media. The use of gelatin/collagen electrospun nanofibers in this form is thus greatly restricted for biomedicine. Therefore, the cross-linking of these fibers is necessary for controlling their aqueous solubility. This led to enhanced biological characteristics of the fibers, rendering them excellent options for various biomedical uses. The objective of this review is to highlight the key research related to the electrospinning of collagen and gelatin, as well as their applications in the biomedical field. The review features a detailed examination of the electrospinning fiber mats, showcasing their varying structures and performances resulting from diverse solvents, electrospinning processes, and cross-linking methods. Judiciously selected examples from literature will be presented to demonstrate major advantages of such biofibers. The current developments and difficulties in this area of research are also being addressed.

Graphene-silymarin-loaded chitosan/gelatin/hyaluronic acid hybrid constructs for advanced full-thickness burn wound management

Burn wounds (BWs) with extensive blood loss, along with bacterial infections and poor healing, may become detrimental and pose significant rehabilitation obstacles in medical facilities. Therefore, the freeze-drying method synthesized novel hemocompatible chitosan, gelatin, and hyaluronic acid infused with graphene oxide-silymarin (CGH-SGO) hybrid constructs for application as a BW patch. Most significantly, synthesized hybrid constructs exhibited an interconnected-porous framework with precise pore sizes (≈118.52 µm) conducive to biological functions. Furthermore, the FTIR and XRD analyses document the constructs' physiochemical interactions. Similarly, enhanced swelling ratios, adequate WVTR (736 ± 78 g m-2 hr-1), and bio-degradation rates were seen during the physiological examination of constructs. Following the in vitro investigations, SMN-GO added to constructs improved their anti-bacterial (against E.coli and S. aureus), anti-oxidant, hemocompatible, and bio-compatible characteristics in conjunction with prolonged drug release. Furthermore, in vivo, implanting constructs on wounds exhibited significant acceleration in full-thickness burn wound (FT-BW) healing on the 14th day (CGH-SGO: 95 ± 2.1 %) in contrast with the control (Gauze: 71 ± 4.2 %). Additionally, contrary to gauze, the in vivo rat tail excision model administered with constructs assured immediate blood clotting. Therefore, CGH-SGO constructs with an improved porous framework, anti-bacterial activity, hemocompatibility, and biocompatibility could represent an attractive option for healing FT-BWs.

Recent advances on enhancing 3D printing quality of protein-based inks: A review

3D printing is an additive manufacturing technology that locates constructed models with computer-controlled printing equipment. To achieve high-quality printing, the requirements on rheological properties of raw materials are extremely restrictive. Given the special structure and high modifiability under external physicochemical factors, the rheological properties of proteins can be easily adjusted to suitable properties for 3D printing. Although protein has great potential as a printing material, there are many challenges in the actual printing process. This review summarizes the technical considerations for protein-based ink 3D printing. The physicochemical factors used to enhance the printing adaptability of protein inks are discussed. The post-processing methods for improving the quality of 3D structures are described, and the application and problems of fourth dimension (4D) printing are illustrated. The prospects of 3D printing in protein manufacturing are presented to support its application in food and cultured meat. The native structure and physicochemical factors of proteins are closely related to their rheological properties, which directly link with their adaptability for 3D printing. Printing parameters include extrusion pressure, printing speed, printing temperature, nozzle diameter, filling mode, and density, which significantly affect the precision and stability of the 3D structure. Post-processing can improve the stability and quality of 3D structures. 4D design can enrich the sensory quality of the structure. 3D-printed protein products can meet consumer needs for nutritional or cultured meat alternatives.

Recent advances and biomedical application of 3D printed nanocellulose-based adhesive hydrogels: A review

Nanocellulose-based tissue adhesives show promise for achieving rapid hemostasis and effective wound healing. Conventional methods, such as sutures and staples, have limitations, prompting the exploration of bioadhesives for direct wound adhesion and minimal tissue damage. Nanocellulose, a hydrolysis product of cellulose, exhibits superior biocompatibility and multifunctional properties, gaining interest as a base material for bioadhesive development. This study explores the potential of nanocellulose-based adhesives for hemostasis and wound healing using 3D printing techniques. Nanocellulose enables the creation of biodegradable adhesives with minimal adverse effects and opens avenues for advanced wound healing and complex tissue regeneration, such as skin, blood vessels, lungs, cartilage, and muscle. This study reviews recent trends in various nanocellulose-based 3D printed hydrogel patches for tissue engineering applications. The review also introduces various types of nanocellulose and their synthesis, surface modification, and bioadhesive fabrication techniques via 3D printing for smart wound healing.

Pharmaceutical applications of chitosan in skin regeneration: A review

Skin regeneration is the process that restores damaged tissues. When the body experiences trauma or surgical incisions, the skin and tissues on the wound surface become damaged. The body repairs this damage through complex physiological processes to restore the original structural and functional states of the affected tissues. Chitosan, a degradable natural bioactive polysaccharide, has attracted widespread attention partly owing to its excellent biocompatibility and antimicrobial properties; additionally, a modified form of this compound has been shown to promote skin regeneration. This review evaluates the recent research progress in the application of chitosan to promote skin regeneration. First, we discuss the basic principles of the extraction and preparation processes of chitosan from its source. Subsequently, we describe the functional properties of chitosan and the optimization of these properties through modification. We then focus on the existing chitosan-based biomaterials developed for clinical applications and their corresponding effects on skin regeneration, particularly in cases of diabetic and burn wounds. Finally, we explore the challenges and prospects associated with the use of chitosan in skin regeneration. Overall, this review provides a reference for related research and contributes to the further development of chitosan-based products in cutaneous skin regeneration.

Silver-doped hydroxyapatite laden chitosan-gelatin nanocomposite scaffolds for bone tissue engineering: an in-vitro and in-ovo evaluation

Despite the advancements in bone tissue engineering, the majority of implant failures are caused due to microbial contamination. So, efforts are being made to develop biomaterial with antimicrobial property enhancing the regeneration of damaged bone tissue. In the present study, chitosan-gelatin (CG) scaffolds containing silver-doped hydroxyapatite (AgHAP) nanoparticles at 0.5%, 1.0% and 1.5% (w/v) were fabricated by lyophilization technique. The results confirmed the synthesis of AgHAP nanoparticles and showed interconnected porous structure of the nanocomposite scaffolds with 89%-75% porosity. Similarly, the swelling percentage, degradation behavior and compressive modulus of CG-AgHAP nanocomposite scaffolds were 1666%, 40% and 0.7 MPa, respectively. The developed nanocomposite scaffolds revealed better antimicrobial properties and bioactivity. The cell culture studies showed favorable viability of Wharton's jelly stem cells on CG-AgHAP nanocomposite scaffolds. CAM (chorioallantoic membrane) assay determined the angiogenic potential with better visualization of blood vessels in the CAM area. Hence, the obtained results confirmed that CG-AgHAP3 nanocomposite scaffold was the most suitable for bone tissue engineering applications among all scaffolds.

Thermally-activated gelatin-chitosan-MOF hybrid aerogels for efficient removal of ibuprofen and naproxen

Nonsteroidal anti-inflammatory drugs (NSAIDs) are one of the most frequently used drugs and have been frequently detected in aquatic environments. This paper demonstrates a thermally-activated gelatin-chitosan and amine-functionalized metal-organic framework (UiO-66-NH2) aerogel (CGC-MOF), which was successfully synthesized for the efficient removal of ibuprofen (IBP) and naproxen (NPX). Various characterization tools were used to systematically analyze the microstructure and physicochemical properties of the synthesized aerogel. In addition, the effect of key reaction parameters as well as batch and continuous-flow fixed-bed column experiments were carried out to elucidate the adsorption process. Several functional groups in the biopolymer network, combined with excellent MOF properties, synergistically couple to form an adsorbent with great performance. The mesoporous aerogel activated at 200 °C (CGC-MOF200) exhibited a high specific surface area (819.6 m2/g) that is valuable in providing abundant adsorption active sites that facilitate the efficient adsorption of IBP and NPX. CGC-MOF200 exhibited an excellent removal of IBP and NPX, accounting to 99.28 % and 96.39 %, respectively. The adsorption process followed the pseudo-second-order kinetics and the Freundlich isotherm models, suggesting heterogeneous and chemisorption adsorption processes. Overall, this work provides new and valuable insights into the development of a promising biopolymer-MOF composite aerogel for environmental remediation.

Development of hydrogel-based composite scaffolds containing eggshell particles for bone regeneration applications

This study describes the development and characterization of novel composite scaffolds, made of an alginate-chitosan hydrogel matrix containing eggshell (ES) particles, for bone tissue engineering applications. Scaffolds with ES particles, either untreated or treated with phosphoric acid to create a nanotextured particle surface, were compared to scaffolds without particles. Results indicate that the nanotexturing process exposed occluded ES proteins orthologous to those in human bone extracellular matrix. Scaffolds with ES or nanotextured ES (NTES) particles had a higher porosity (81 ± 4% and 89 ± 5%, respectively) than scaffolds without particles (59 ± 5%) (p = .002 and p < .001, respectively). Scaffolds with NTES particles had a larger median pore size (113 μm [interquartile range [IQ]: 88-140 μm]) than scaffolds with ES particles (94 μm [IQ: 75-112 μm]) and scaffolds without particles (99 μm [IQ: 74-135 μm]) (p < .001 and p = .011, respectively). The compressive modulus of the scaffolds with ES or NTES particles remained low (3.69 ± 0.70 and 3.14 ± 0.62 kPa, respectively), but these scaffolds were more resistant to deformation following maximum compression than those without particles. Finally, scaffolds with ES or NTES particles allowed better retention of human mesenchymal stem cells during seeding (53 ± 12% and 57 ± 8%, respectively, vs. 17 ± 5% for scaffolds without particles; p < .001 in both cases), as well as higher cell viability up to 21 days of culture (67 ± 17% and 61 ± 11%, respectively, vs. 15 ± 7% for scaffolds without particles; p < .001 in both cases). In addition, alkaline phosphatase (ALP) activity increased up to 558 ± 164% on day 21 in the scaffolds with ES particles, and up to 567 ± 217% on day 14 in the scaffolds with NTES particles (p = .006 and p = .002, respectively, relative to day 0). Overall, this study shows that the physicochemical properties of the alginate-chitosan hydrogel scaffolds with ES or NTES particles are similar to those of cancellous bone. In addition, scaffolds with particles supported early osteogenic differentiation and therefore represent a promising new bone substitute, especially for non-load bearing applications.

Characterization of chitosan-gelatin cryogel templates developed by chemical crosslinking and oxidation resistance of camellia oil cryogel-templated oleogels

In this study, chitosan-gelatin conjugates were prepared by chemical crosslinking of tannic acid. The cryogel templates were developed through freeze-drying and immersed in camellia oil to construct cryogel-templated oleogels. Chemical crosslinking resulted in apparent colour changes and improved emulsion-related/rheological properties on conjugates. The cryogel templates with different formulas exhibited different microstructures with high porosities (over 96 %), and crosslinked samples might have higher hydrogen bonding strength. Tannic acid crosslinking also led to enhanced thermal stabilities and mechanical properties. Cryogel templates could reach a considerable oil absorption capacity of up to 29.26 g/g and prevent oil from leaking effectively. The obtained oleogels with high tannic acid content possessed outstanding antioxidant abilities. After 8 days of rapid oxidation at 40 °C, Oleogels with a high degree of crosslinking owned the lowest POV and TBARS values (39.74 nmol/kg, and 24.40 μg/g, respectively). This study indicates that the involvement of chemical crosslinking would favor the preparation and the application potential of cryogel-templated oleogels, and the tannic acid in the composite biopolymer systems could act as both the crosslinking agent and the antioxidant.

Aligned Ice Templated Biomaterial Strategies for the Musculoskeletal System

Aligned pore structures present many advantages when conceiving biomaterial strategies for treatment of musculoskeletal disorders. Aligned ice templating (AIT) is one of the many different techniques capable of producing anisotropic porous scaffolds; its high versatility allows for the formation of structures with tunable pore sizes, as well as the use of many different materials. AIT has been found to yield improved compressive properties for bone tissue engineering (BTE), as well as higher tensile strength and optimized cellular alignment and proliferation in tendon and muscle repair applications. This review evaluates the work that has been done in the last decade toward the production of aligned pore structures by AIT with an outlook on the musculoskeletal system. This work describes the fundamentals of the AIT technique and focuses on the research carried out to optimize the biomechanical properties of scaffolds by modifying the pore structure, categorizing by material type and application. Related topics including growth factor incorporation into AIT scaffolds, drug delivery applications, and studies about immune system response will be discussed.

The marriage of immunomodulatory, angiogenic, and osteogenic capabilities in a piezoelectric hydrogel tissue engineering scaffold for military medicine

BACKGROUND

Most bone-related injuries to grassroots troops are caused by training or accidental injuries. To establish preventive measures to reduce all kinds of trauma and improve the combat effectiveness of grassroots troops, it is imperative to develop new strategies and scaffolds to promote bone regeneration.

METHODS

In this study, a porous piezoelectric hydrogel bone scaffold was fabricated by incorporating polydopamine (PDA)-modified ceramic hydroxyapatite (PDA-hydroxyapatite, PHA) and PDA-modified barium titanate (PDA-BaTiO₃, PBT) nanoparticles into a chitosan/gelatin (Cs/Gel) matrix. The physical and chemical properties of the Cs/Gel/PHA scaffold with 0-10 wt% PBT were analyzed. Cell and animal experiments were performed to characterize the immunomodulatory, angiogenic, and osteogenic capabilities of the piezoelectric hydrogel scaffold in vitro and in vivo.

RESULTS

The incorporation of BaTiO₃ into the scaffold improved its mechanical properties and increased self-generated electricity. Due to their endogenous piezoelectric stimulation and bioactive constituents, the as-prepared Cs/Gel/PHA/PBT hydrogels exhibited cytocompatibility as well as immunomodulatory, angiogenic, and osteogenic capabilities; they not only effectively induced macrophage polarization to M2 phenotype but also promoted the migration, tube formation, and angiogenic differentiation of human umbilical vein endothelial cells (HUVECs) and facilitated the migration, osteo-differentiation, and extracellular matrix (ECM) mineralization of MC3T3-E1 cells. The in vivo evaluations showed that these piezoelectric hydrogels with versatile capabilities significantly facilitated new bone formation in a rat large-sized cranial injury model. The underlying molecular mechanism can be partly attributed to the immunomodulation of the Cs/Gel/PHA/PBT hydrogels as shown via transcriptome sequencing analysis, and the PI3K/Akt signaling axis plays an important role in regulating macrophage M2 polarization.

CONCLUSION

The piezoelectric Cs/Gel/PHA/PBT hydrogels developed here with favorable immunomodulation, angiogenesis, and osteogenesis functions may be used as a substitute in periosteum injuries, thereby offering the novel strategy of applying piezoelectric stimulation in bone tissue engineering for the enhancement of combat effectiveness in grassroots troops.

Direct Integration of 3D Printing and Cryogel Scaffolds for Bone Tissue Engineering

Cryogels, known for their biocompatibility and porous structure, lack mechanical strength, while 3D-printed scaffolds have excellent mechanical properties but limited porosity resolution. By combining a 3D-printed plastic gyroid lattice scaffold with a chitosan-gelatin cryogel scaffold, a scaffold can be created that balances the advantages of both fabrication methods. This study compared the pore diameter, swelling potential, mechanical characteristics, and cellular infiltration capability of combined scaffolds and control cryogels. The incorporation of the 3D-printed lattice demonstrated patient-specific geometry capabilities and significantly improved mechanical strength compared to the control cryogel. The combined scaffolds exhibited similar porosity and relative swelling ratio to the control cryogels. However, they had reduced elasticity, reduced absolute swelling capacity, and are potentially cytotoxic, which may affect their performance. This paper presents a novel approach to combine two scaffold types to retain the advantages of each scaffold type while mitigating their shortcomings.

Cerium oxide nanoparticles disseminated chitosan gelatin scaffold for bone tissue engineering applications

Cell-free and cell-loaded constructs are used to bridge the critical-sized bone defect. Oxidative stress at the site of the bone defects is a major interference that slows bone healing. Recently, there has been an increase in interest in enhancing the properties of three-dimensional scaffolds with free radical scavenging materials. Cerium oxide nanoparticles (CNPs) can scavenge free radicals due to their redox-modulating property. In this study, freeze-drying was used to fabricate CG-CNPs nanocomposite scaffolds using gelatin (G), chitosan (C), and cerium oxide nanoparticles. Physico-chemical, mechanical, and biological characterization of CG-CNPs scaffolds were studied. CG-CNPs scaffolds demonstrated better results in terms of physicochemical, mechanical, and biological properties as compared to CG-scaffold. CG-CNPs scaffolds were cyto-friendly to MC3T3-E1 cells studied by performing in-vitro and in-ovo studies. The scaffold's antimicrobial study revealed high inhibition zones against Gram-positive and Gram-negative bacteria. With 79 % porosity, 45.99 % weight loss, 178.25 kPa compressive modulus, and 1.83 Ca/P ratio, the CG-CNP₂ scaffold displays the best characteristics. As a result, the CG-CNP₂ scaffolds are highly biocompatible and could be applied to repair bone defects.

Macroporous Cell-Laden Gelatin/Hyaluronic Acid/Chondroitin Sulfate Cryogels for Engineered Tissue Constructs

Cryogels are a unique macroporous material for tissue engineering. In this work, we study the effect of hyaluronic acid on the physicochemical properties of cryogel as well as on the proliferation of a 3D model of mesenchymal stem cells. The functional groups of the synthesized cryogels were identified using Fourier transform infrared spectroscopy. With an increase in the content of hyaluronic acid in the composition of the cryogel, an increase in porosity, gel content and swelling behavior was observed. As the hyaluronic acid content increased, the average pore size increased and more open pores were formed. Degradation studies have shown that all cryogels were resistant to PBS solution for 8 weeks. Cytotoxicity assays demonstrated no toxic effect on viability of rat adipose-derived mesenchymal stem cells (ADMSCs) cultured on cryogels. ADMSC spheroids were proliferated on scaffolds and showed the ability of the cryogels to orient cell differentiation into chondrogenic lineage even in the absence of inductive agents. Thus, our results demonstrate an effective resemblance to extracellular matrix structures specific to cartilage-like microenvironments by cryogels and their further perspective application as potential biomaterials.

Passivator-Free Microwave–Hydrothermal Synthesis of High Quantum Yield Carbon Dots for All-Carbon Fluorescent Nanocomposite Films

Based on the self-passivation function of chitosan, an efficient, and green synthesis strategy was applied to prepare chitosan carbon dots (CDs). The quantum yield of carbon dots reached 35% under the conditions of hydrothermal temperature of 200 °C, hydrothermal time of 5 h, and chitosan concentration of 2%. Moreover, the obtained carbon dots had high selectivity and sensitivity to Fe3+. Based on the Schiff base reaction between the aldehyde groups of dialdehyde cellulose nanofibrils (DNF) and the amino groups of CDs, a chemically cross-linked, novel, fluorescent composite film, with high transparency and high strength, was created using one-pot processing. Knowing that the fluorescence effect of the composite film on Fe3+ had a linear relationship in the concentration range of 0–100 μM, a fluorescent probe can be developed for quantitative analysis and detection of Fe3+. Owing to their excellent fluorescent and mechanical properties, the fluorescent nanocomposite films have potential applications in the fields of Fe3+ detection, fluorescent labeling, and biosensing.

Dialdehyde Starch Nanocrystals as a Novel Cross-Linker for Biomaterials Able to Interact with Human Serum Proteins

In recent years, new cross-linkers from renewable resources have been sought to replace toxic synthetic compounds of this type. One of the most popular synthetic cross-linking agents used for biomedical applications is glutaraldehyde. However, the unreacted cross-linker can be released from the materials and cause cytotoxic effects. In the present work, dialdehyde starch nanocrystals (NDASs) were obtained from this polysaccharide nanocrystal form as an alternative to commonly used cross-linking agents. Then, 5-15% NDASs were used for chemical cross-linking of native chitosan (CS), gelatin (Gel), and a mixture of these two biopolymers (CS-Gel) via Schiff base reaction. The obtained materials, forming thin films, were characterized by ATR-FTIR, SEM, and XRD analysis. Thermal and mechanical properties were determined by TGA analysis and tensile testing. Moreover, all cross-linked biopolymers were also characterized by hydrophilic character, swelling ability, and protein absorption. The toxicity of obtained materials was tested using the Microtox test. Dialdehyde starch nanocrystals appear as a beneficial plant-derived cross-linking agent that allows obtaining cross-linked biopolymer materials with properties desirable for biomedical applications.

Tubular TPU/SF nanofibers covered with chitosan-based hydrogels as small-diameter vascular grafts with enhanced mechanical properties

Native grafts such as internal mammary artery and saphenous vein are the main choice for coronary artery bypass graft. However, due to the limitations associated with their availability and rapid failure caused by hyperplasia, small diameter tissue-engineered vascular grafts (TEVGs) with sufficient post-implantation patency are urgently demanded as artificial alternatives. In our previous work, we innovatively fabricated a bilayer vascular graft providing appropriate structural and biological properties using electrospinning and freeze-drying methods. It was proved that the mechanical properties of the proposed graft enhanced in comparison with using either of methods individually. Here, we adopted the same methods and incorporated an anticoagulant internal layer (inner diameter 4 mm), comprised of co-electrospun fibers of silk fibroin (SF) and heparinized thermoplastic polyurethane (TPU), and an external highly porous hydrogel fabricated by freeze-drying method. The electrospun layer exhibited strong mechanical properties including superior elastic modulus (4.92 ± 0.11 MPa), suture retention force (6.73 ± 0.83 N), elongation at break (196 ± 4%), and comparable burst pressure (1140 ± 12 mmHg) while the external hydrogel provided SMCs viability. The heparin was released in a sustain manner over 40 days, and the cytocompatibility and blood compatibility of scaffold were approved using MTT assay and platelet adhesion test. Thus, the proposed graft has a potential to be used as an artificial blood vessel scaffold for later in-vivo transplantation.

Development of Cellulose Nanofibril/Casein-Based 3D Composite Hemostasis Scaffold for Potential Wound-Healing Application

Excessive bleeding in traumatic hemorrhage is the primary concern for natural wound healing and the main reason for trauma deaths. The three-dimensional (3D) bioprinting of bioinks offers the desired structural complexity vital for hemostasis activity and targeted cell proliferation in rapid and controlled wound healing. However, it is challenging to develop suitable bioinks to fabricate specific 3D scaffolds desirable in wound healing. In this work, a 3D composite scaffold is designed using bioprinting technology and synergistic hemostasis mechanisms of cellulose nanofibrils (TCNFs), chitosan, and casein to control blood loss in traumatic hemorrhage. Bioinks that consist of casein bioconjugated TCNF (with a casein content of 104.5 ± 34.1 mg/g) using the carbodiimide cross-linker chemistry were subjected to bioprinting for customizable 3D scaffold fabrication. Further, the 3D composite scaffolds were in situ cross-linked using a green ionic complexation approach. The covalent conjugation among TCNF, casein, and chitosan was confirmed by Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE), and X-ray diffraction (XRD) studies. The in vitro hemostasis activity of the 3D composite scaffold was analyzed by a human thrombin-antithrombin (TAT) assay and adsorption of red blood cells (RBCs) and platelets. The 3D composite scaffold had a better swelling behavior and a faster whole blood clotting rate at each time point than the 3D TCNF scaffold and commercial cellulose-based dressings. The TAT assay demonstrated that the 3D composite scaffold could form a higher content of thrombin (663.29 pg/mL) and stable blood clot compared to a cellulosic pad (580.35 pg/mL), 3D TCNF (457.78 pg/mL), and cellulosic gauze (328.92 pg/mL), which are essential for faster blood coagulation. In addition, the 3D composite scaffold had a lower blood clotting index (23.34%) than the 3D TCNF scaffold (41.93%), suggesting higher efficiencies for RBC entrapping to induce blood clotting. The in vivo cytocompatibility was evaluated by a 3D cell culture study, and results showed that the 3D composite scaffold could promote growth and proliferation of NIH 3T3 fibroblast cells, which is vital for wound healing. Cellulase-based in vitro deconstruction of the 3D composite scaffold showed significant weight loss (80 ± 5%) compared to the lysozyme hydrolysis (22 ± 5%) after 28 days of incubation, suggesting the biodegradation potential of the composite scaffold. In conclusion, this study proposes efficient prospects to develop a 3D composite scaffold from bioprinting of TCNF-based bioinks that can accelerate blood clotting and wound healing, suggesting its potential application in reducing blood loss during traumatic hemorrhage.

Nanocatalyst doped bacterial cellulose-based thermosensitive nanogel with biocatalytic function for antibacterial application

Reactive oxygen species (ROS) for treating bacterial infection is an alternative strategy to overcome the drawbacks such as bacterial resistance of commonly used antibiotics. Nanocatalysts have been proved highly effective in regulating intracellular ROS level due to their intrinsic enzymes-mimicking ability. Herein, we prepared a carbon-based nanozyme doped with copper atoms with peroxidase mimetic activity to catalyze the decomposition of bio-safety dosage of H₂O₂ to highly reactive OH radicals for antibacterial treatment. Furthermore, we designed the thermo-responsive nanogels consisting of bacterial cellulose nanowhiskers as the carrier of the nanozyme. The obtained nanogels displayed remarkable intelligent response to temperature change with sol-gel transition temperature of ~33 °C and in situ gel forming ability. Moreover, the nanogels exhibited excellent biocompatibility in vitro, along with remarkable antibacterial efficacy which could inactivate 6.36 log of S. aureus and 6.01 log of E. coli in 3 h, respectively. The findings provide a novel strategy for advancing the development of nanocatalysts-based responsive biomaterials for treating bacterial infections.

Inducing Microscale Structural Order in Phage Nanofilament Hydrogels with Globular Proteins

Biological hydrogels play important physiological roles in the body. These hydrogels often contain ordered subdomains that provide mechanical toughness and other tissue-specific functionality. Filamentous bacteriophages are nanofilaments with a high aspect ratio that can self-assemble into liquid crystalline domains that could be designed to mimic ordered biological hydrogels and can thus find applications in biomedical engineering. We have previously reported hydrogels of pure cross-linked liquid crystalline filamentous phage formed at very high concentrations exhibiting a tightly packed microstructure and high stiffness. In this work, we report a method for inducing self-assembly of filamentous phage into liquid crystalline hydrogels at concentrations that are several orders of magnitude below that of lyotropic liquid crystal formation, thus creating structural order but a less densely packed microstructure. Hybrid hydrogels of M13 phage and bovine serum albumin (0.25 w/v%) were formed and shown to adsorb up to 16× their weight in water. Neither component gelled on its own at the low concentrations used, suggesting synergistic action between the two components in the formation of the hydrogel. The hybrid hydrogels exhibited repetitive self-healing under physiological conditions and at room temperature, autofluorescence in three channels, and antibacterial activity toward Escherichia coli host cells. Furthermore, the hybrid hydrogels exhibited a more than 2× higher ability to pack water compared to BSA-only hydrogels and 2× lower compression modulus compared to tightly packed M13-only hydrogels, suggesting that our method could be used to create hydrogels with tunable mechanical properties and pore structure through the addition of globular proteins, while maintaining bioactivity and microscale structural order.

Multifunctional Gelatin/Chitosan Electrospun Wound Dressing Dopped with Undaria pinnatifida Phlorotannin-Enriched Extract for Skin Regeneration

The similarities of electrospun fibers with the skin extracellular matrix (ECM) make them promising structures for advanced wound dressings. Moreover, infection and resistance in wounds are a major health concern that may be reduced with antibacterial wound dressings. In this work, a multifunctional wound dressing was developed based on gelatin/chitosan hybrid fibers dopped with phlorotannin-enrich extract from the seaweed Undaria pinnatifida. The intrinsic electrospun structure properties combined with the antimicrobial and anti-inflammatory properties of phlorotannin-enrich extract will enhance the wound healing process. Electrospun meshes were produced by incorporating 1 or 2 wt% of extract, and the structure without extract was used as a control. Physico-chemical, mechanical, and biological properties were evaluated for all conditions. Results demonstrated that all developed samples presented a homogenous fiber deposition with the average diameters closer to the native ECM fibrils, and high porosities (~90%) that will be crucial to control the wound moist environment. According to the tensile test assays, the incorporation of phlorotannin-enriched extract enhances the elastic performance of the samples. Additionally, the extract incorporation made the structure stable over time since its in vitro degradation rates decreased under enzymatic medium. Extract release profile demonstrated a longstanding delivery (up to 160 days), reaching a maximum value of ~98% over time. Moreover, the preliminary antimicrobial results confirm the mesh's antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus. In terms of biological characterization, no condition presented cytotoxicity effects on hDNF cells, allowing their adhesion and proliferation over 14 days, except the condition of 2 wt% after 7 days. Overall, the electrospun structure comprising phlorotannins-enriched extract is a promising bioactive structure with potential to be used as a drug delivery system for skin regeneration by reducing the bacterial infection in the wound bed.

Advances in the synthesis and application of self-assembling biomaterials

The present study scrutinized some of the crucial advancements in the synthesis and functionalisation of self-assembling biomaterials for application in biomedicine. The basic concept of self-organization was discussed along with the mechanisms and methods involved in its implementation with biomaterials. Further, several recent applications of this technology in the biological and medical domain, and the avenues for future research and development were presented. This study brought to focus the vast potential of basic and applied research involved, especially in the context of hybrids and composites, as well as the difference in pace of new developments for different types of biomolecular materials. As nanobiotechnology matures, the tools and techniques available for developing and controlling self-assembled biomaterials as well as studying their interaction with biological tissue, will grow exponentially. Presently, self-assembly remains a potent tool for the synthesis of functional biomaterials.

Translational Research for Orthopedic Bone Graft Development

Designing biomaterials for bone-substitute applications is still a challenge regarding the natural complex structure of hard tissues. Aiming at bone regeneration applications, scaffolds based on natural collagen and synthetic nanohydroxyapatite were developed, and they showed adequate mechanical and biological properties. The objective of this work was to perform and evaluate a scaled-up production process of this porous biocomposite scaffold, which promotes bone regeneration and works as a barrier for both fibrosis and the proliferation of scar tissue. The material was produced using a prototype bioreactor at an industrial scale, instead of laboratory production at the bench, in order to produce an appropriate medical device for the orthopedic market. Prototypes were produced in porous membranes that were e-beam irradiated (the sterilization process) and then analysed by scanning electron microscopy (SEM), confocal laser scanning microscopy (CLSM), dynamic mechanical analysis (DMA), cytotoxicity tests with mice fibroblasts (L929), human osteoblast-like cells (MG63) and human MSC osteogenic differentiation (HBMSC) with alkaline phosphatase (ALP) activity and qPCR for osteogenic gene expression. The prototypes were also implanted into critical-size bone defects (rabbits' tibia) for 5 and 15 weeks, and after that were analysed by microCT and histology. The tests performed for the physical characterization of the materials showed the ability of the scaffolds to absorb and retain water-based solvents, as well as adequate mechanical resistance and viscoelastic properties. The cryogels had a heteroporous morphology with microporosity and macroporosity, which are essential conditions for the interaction between the cells and materials, and which consequently promote bone regeneration. Regarding the biological studies, all of the studied cryogels were non-cytotoxic by direct or indirect contact with cells. In fact, the scaffolds promoted the proliferation of the human MSCs, as well as the expression of the osteoblastic phenotype (osteogenic differentiation). The in vivo results showed bone tissue ingrowth and the materials' degradation, filling the critical bone defect after 15 weeks. Before and after irradiation, the studied scaffolds showed similar properties when compared to the results published in the literature. In conclusion, the material production process upscaling was optimized and the obtained prototypes showed reproducible properties relative to the bench development, and should be able to be commercialized. Therefore, it was a successful effort to harness knowledge from the basic sciences to produce a new biomedical device and enhance human health and wellbeing.

Hybrid Methacrylated Gelatin and Hyaluronic Acid Hydrogel Scaffolds. Preparation and Systematic Characterization for Prospective Tissue Engineering Applications

Hyaluronic acid (HA) and gelatin (Gel) are major components of the extracellular matrix of different tissues, and thus are largely appealing for the construction of hybrid hydrogels to combine the favorable characteristics of each biopolymer, such as the gel adhesiveness of Gel and the better mechanical strength of HA, respectively. However, despite previous studies conducted so far, the relationship between composition and scaffold structure and physico-chemical properties has not been completely and systematically established. In this work, pure and hybrid hydrogels of methacroyl-modified HA (HAMA) and Gel (GelMA) were prepared by UV photopolymerization and an extensive characterization was done to elucidate such correlations. Methacrylation degrees of ca. 40% and 11% for GelMA and HAMA, respectively, were obtained, which allows to improve the hydrogels’ mechanical properties. Hybrid GelMA/HAMA hydrogels were stiffer, with elastic modulus up to ca. 30 kPa, and porous (up to 91%) compared with pure GelMA ones at similar GelMA concentrations thanks to the interaction between HAMA and GelMA chains in the polymeric matrix. The progressive presence of HAMA gave rise to scaffolds with more disorganized, stiffer, and less porous structures owing to the net increase of mass in the hydrogel compositions. HAMA also made hybrid hydrogels more swellable and resistant to collagenase biodegradation. Hence, the suitable choice of polymeric composition allows to regulate the hydrogels´ physical properties to look for the most optimal characteristics required for the intended tissue engineering application.

Development and characterization of a new chitosan-based scaffold associated with gelatin, microparticulate dentin and genipin for endodontic regeneration

OBJECTIVE

An ideal scaffold for endodontic regeneration should allow the predictableness of the new tissue organization and limit the negative impact of residual bacteria. Therefore, composition and functionalization of the scaffold play an important role in tissue bioengineering. The objective of this study was to assess the morphological, physicochemical, biological and antimicrobial properties of a new solid chitosan-based scaffold associated with gelatin, microparticulate dentin and genipin.

METHODS

Scaffolds based on chitosan (Ch); chitosan associated with gelatin and genipin (ChGG); and chitosan associated with gelatin, microparticulate dentin and genipin (ChGDG) were prepared by using the freeze-drying method. The morphology of the scaffolds was analyzed by scanning electron microscopy (SEM). The physicochemical properties were assessed for biodegradation, swelling and total released proteins. The biological aspects of the scaffolds were assessed using human cells from the apical papilla (hCAPs). Cell morphology and adhesion to the scaffolds were evaluated by SEM, cytotoxicity and cell proliferation by MTT reduction-assay. Cell differentiation in scaffolds was assessed by using alizarin red assay. The antimicrobial effect of the scaffolds was evaluated by using the bacterial culture method, and bacterial adhesion to the scaffolds was observed by SEM.

RESULTS

All the scaffolds presented porous structures. The ChCDG had more protein release, adhesion, proliferation and differentiation of hCAPs, and bacteriostatic effect on Enterococcus faecalis than Ch and ChGG (p < 0.05).

SIGNIFICANCE

The chitosan associated with gelatin, microparticulate dentin and genipin has morphological, physicochemical, biological and antibacterial characteristics suitable for their potential use as scaffold in regenerative endodontics.

Development of Inherently Antibacterial, Biodegradable, and Biologically Active Chitosan/Pseudo-Protein Hybrid Hydrogels as Biofunctional Wound Dressings

Developing a new family of hydrogel-based wound dressings that could have a dual biofunctionality of antibacterial and biological responses is highly desirable. In this study, an inherently effective antibacterial and biodegradable hydrogel dressing without the need for impregnated antibiotics was designed, synthesized, characterized, and examined for its effect on macrophages, which initiated inflammatory activity and activated both NO and TNF-α production for the purpose of achieving a better and faster wound healing. The purposes of this research was to develop a novel family of cationic biodegradable hydrogels based on arginine-based poly(ester urea urethane) (Arg-PEUU) and glycidyl methacrylate-modified chitosan (CS-GMA) that has both inherent antibacterial and bioactive functionality as a wound healing dressing for accelerated healing of contaminated or infected wounds. These hybrid hydrogels present a well-defined three-dimensional microporous network structure and have a high water absorption ability, and their biodegradation is effectively accelerated in the presence of lysozymes. The hemolytic activity test, MTT assay, and live/dead assay of these hybrid hydrogels indicated that they had no cytotoxicity toward red blood cells, NIH-3T3 fibroblast cells, and human vascular endothelial cells, thus corroborating their cytocompatibility. Furthermore, these hybrid hydrogels could elevate the release of both produced NO and TNF-α by stimulating and activating RAW 264.7 macrophages, augmenting their antibacterial biological response. The antibacterial assay of these hybrid hydrogels demonstrated their excellent antibacterial activity without the need for impregnated antibacterial agents. Taken together, this new family of biodegradable, antibacterial, and biologically responsive hybrid hydrogels exhibits great potential as biofunctional antibacterial wound dressing candidates for wound healing.

A Comparative Review of Natural and Synthetic Biopolymer Composite Scaffolds

Tissue engineering (TE) and regenerative medicine integrate information and technology from various fields to restore/replace tissues and damaged organs for medical treatments. To achieve this, scaffolds act as delivery vectors or as cellular systems for drugs and cells; thereby, cellular material is able to colonize host cells sufficiently to meet up the requirements of regeneration and repair. This process is multi-stage and requires the development of various components to create the desired neo-tissue or organ. In several current TE strategies, biomaterials are essential components. While several polymers are established for their use as biomaterials, careful consideration of the cellular environment and interactions needed is required in selecting a polymer for a given application. Depending on this, scaffold materials can be of natural or synthetic origin, degradable or nondegradable. In this review, an overview of various natural and synthetic polymers and their possible composite scaffolds with their physicochemical properties including biocompatibility, biodegradability, morphology, mechanical strength, pore size, and porosity are discussed. The scaffolds fabrication techniques and a few commercially available biopolymers are also tabulated.

Feasibility Study of Gelatin Preparation from the Bioinspired Collagen Aggregates by a "Two-step" Facile Degradation Method

Gelatin is the putative research hotspot of natural products, but gelatin prepared by traditional alkali methods has seriously affected its applications due to the worryingly low molecular weight and poor gel strength. Herein, we took the lead to extract the distinct gelatin from a kind of bioinspired collagen aggregate (CA) by a two-step controlled degradation method. Structural analysis suggested that the CA better preserves the natural aggregated structure of nature collagen (typical D-periodic cross-striated pattern). Compared with the gelatin gelatinized by the conventional alkali method (G-Al) and commercial gelatin (CG), the gelatin (G-CA) from CA had a wide molecular weight distribution range, high transparency, high viscosity, and strong gel strength as expected. Meanwhile, the G-CA film exhibited better mechanical performance and thermostability than CG and G-Al films, and water vapor permeability was also higher in the G-CA film, whereas water solubility was higher in the CG and G-Al films. Thus, the G-CA film is more conducive to the use of food packaging or edible films, exhibiting more potential market application prospects. Notably, G-CA based on CA from waste hide offal provides a way to reuse leather waste resources and further realize green and clean production in leather industry.

Filamentous Phages as Building Blocks for Bioactive Hydrogels

Filamentous bacteriophages (bacterial viruses) are semiflexible proteinous nanofilaments with high aspect ratios for which the surface chemistry can be controlled with atomic precision via genetic engineering. That, in addition to their ability to self-propagate and replicate a nearly monodisperse batch of biologically and chemically identical nanofilaments, makes these bionanofilaments superior to most synthetic nanoparticles and thus a powerful tool in the bioengineers' toolbox. Furthermore, filamentous phages form liquid crystalline structures at high concentrations; these ordered assemblies create hierarchically ordered macro-, micro-, and nanostructures that, once cross-linked, can form hierarchically ordered hydrogels, hydrated soft material with a variety of physical and chemical properties suitable for biomedical applications (e.g., wound dressings and tissue engineering scaffolds) as well as biosensing, diagnostic assays. We provide a critical review of these hydrogels of filamentous phage, and their physical, mechanical, chemical, and biological properties and current applications, as well as an overview of limitations and challenges and outlook for future applications. In addition, we present a list of design parameters for filamentous phage hydrogels to serve as a guide for the (bio)engineer and (bio)chemist interested in utilizing these powerful bionanofilaments for designing smart, bioactive materials and devices.

Synthesis and characterization of scaffolds produced under mild conditions based on oxidized cashew gums and carboxyethyl chitosan

This study describes the development of scaffolds based on carboxyethyl chitosan (CEC) and different oxidized cashew gums (CGOx) for tissue engineering (TE) applications. After the physico-chemical characterizations of CEC and CGOx (oxidation degree of 20, 35 and 50%), these macromolecules were used for producing the CGOx-CEC hydrogels through a Schiff base reaction, in the absence of any crosslinking agent. The CGOx-CEC scaffolds obtained after a freeze-drying process were characterized for their morphology, mechanical properties, swelling ability, degradation, and porosity. Those revealed to be highly porous (25-65%), and showed a stable swelling behavior, as well as degradation properties in the absence of enzymes. The use of the cashew gum with higher degree of oxidation led to scaffolds with higher crosslinking densities and increased compressive modulus. None of the hydrogels show cytotoxicity during the 14 days of incubation. Considering all the properties mentioned, these scaffolds are excellent candidates for soft tissue regeneration, owing to the use of eco-friendly starting materials and the easy tuning of their properties.

Recent Advances in Porous 3D Cellulose Aerogels for Tissue Engineering Applications: A Review

Current approaches in developing porous 3D scaffolds face various challenges, such as failure of mimicking extracellular matrix (ECM) native building blocks, non-sustainable scaffold fabrication techniques, and lack of functionality. Polysaccharides and proteins are sustainable, inexpensive, biodegradable, and biocompatible, with structural similarities to the ECM. As a result, 3D-structured cellulose (e.g., cellulose nanofibrils, nanocrystals and bacterial nanocellulose)-based aerogels with high porosity and interconnected pores are ideal materials for biomedical applications. Such 3D scaffolds can be prepared using a green, scalable, and cost-effective freeze-drying technique. The physicochemical, mechanical, and biological characteristics of the cellulose can be improved by incorporation of proteins and other polysaccharides. This review will focus on recent developments related to the cellulose-based 3D aerogels prepared by sustainable freeze-drying methods for tissue engineering applications. We will also provide an overview of the scaffold development criteria; parameters that influenced the aerogel production by freeze-drying; and in vitro and in vivo studies of the cellulose-based porous 3D aerogel scaffolds. These efforts could potentially help to expand the role of cellulose-based 3D scaffolds as next-generation biomaterials.

Chitosan-Based Bioactive Glass Gauze: Microstructural Properties, In Vitro Bioactivity, and Biological Tests

Passive commercial gauzes were turned into interactive wound dressings by impregnating them with a chitosan suspension. To further improve healing, and cell adhesion and proliferation, chitosan/bioactive glass wound dressings were produced with the addition of (i) 45S5, (ii) a Sr- and Mg-containing bioactive glass, and (iii) a Zn-containing bioactive glass to the chitosan suspension. SEM and FTIR analyses evidenced positive results in terms of incorporation of bioactive glass particles. Bioactivity was investigated by soaking chitosan-based bioactive glass wound dressings in simulated body fluid (SBF). Cell viability, proliferation, and morphology were investigated using NIH 3T3 (mouse embryonic fibroblast) cells by neutral red (NR) uptake and MTT assays. Furthermore, the wound-healing rate was evaluated by means of the scratch test, using NIH 3T3. The results showed that bioactive glass particles enhance cell adhesion and proliferation, and wound healing compared to pure chitosan. Therefore, chitosan-based bioactive glass wound dressings combine the properties of the organic matrix with the specific biological characteristics of bioactive glasses to achieve chitosan composites suitable for healing devices.