Preparation and characterization of starch nanocrystals combining ball milling with acid hydrolysis

Exploring effect of uniform dry ball-milling duration on pasting and rheological properties of pink potato and maize starch mixtures

This study examined the potential effect of ball milling on maize starch (MS), pink potato starch (PPS), and their blends in various ratios (90:10, 80:20, and 70:30) on the pasting and rheological properties. Ball-milling led to changes in the particle size, ranging from 652.9 to 6488 nm, and a decrease in relative crystallinity (RC), as confirmed by XRD. Ball-milling increased amylose concentration in blend with the ratio of 90:10 up to 32.53 %, indicating structural alterations and molecular interactions. FESEM analysis confirms significant changes in the surface and particle sizes and starch gels with honeycomb structures. FTIR and Raman spectroscopy revealed a decrease in the intensity of the 1044 cm-1 and 480 cm-1 bands, respectively, signifying structural changes. Pasting parameters like peak viscosity and gelatinization behavior varied with PPS incorporation. The 80:20 blend had the highest viscosity, demonstrating PPS's capacity for high-viscosity starch paste. Rheological measurements of starch blends exhibited shear-thinning behavior, whereas the viscoelastic properties of the blends are influenced by particle size and the ratio of pink potato starch. Ball-milling treatment affects the granules and causes molecular-level interactions between the particles. This results in unique rheological properties of the starch blends, making them suitable for various applications.

High-efficiency preparation of starch nanocrystals with small size and high crystallinity by ethanol-acid penetration and dry-heating pretreatment

Ethanol-acid penetration and drying-heating treatment was developed to shorten the preparation time and improve the quality of starch nanocrystals (SNCs). After treatment by optimized parameters, including 40 % ethanol solution, 10.6 mM chloric acid, and heating time of 1.5 h or 2.0 h, the starches exhibited weakened internal structure and relatively complete crystalline structure. Compared with the regular preparation of only acid hydrolysis, the regular final yield (8.5 % after 5 days) was reached in 48 h and 12 h of the starch heated at 1.5 h and 2.0 h, respectively. The micromorphology, molecular weight, and crystalline structure evaluation demonstrated that the collected nanoparticles were indeed SNCs with smaller size and higher relative crystallinity than regular SNCs. Further analysis found that the SNCs had better crystalline lamellae, higher thermal stability, and lower proportion of phosphorus and sulfur atoms than regular SNCs. This provided a potential method for the high-efficiency preparation of SNCs.

Pickering emulsions stabilized by starch nanocrystals prepared from various crystalline starches by ultrasonic assisted acetic acid: Stability and delivery of curcumin

Ultrasonic assisted acetic acid hydrolysis was applied to prepare starch nanocrystals (SNCs) from native starches with different crystalline structures (A, B, and C types). The structure properties, morphology, Pickering emulsion stability and curcumin deliver capacity of both SNCs and native starches were investigated and compared. Compared with native starches, SNCs showed smaller size and higher crystallinity. The size of SNCs varied with different crystalline types, with C-type starch exhibiting the smallest SNCs (107.4 nm), followed by A-type (113.8 nm), and B-type displaying the largest particle size (149.0 nm). SNCs-Pickering emulsion showed enhanced stability with smaller emulsion droplets, higher static stability, and denser oil/water interface. SNCs-Pickering emulsions displayed higher curcumin loading efficiency (53.53 %-61.41 %) compared with native starch-Pickering emulsions (13.93 %-19.73 %). During in vitro digestion, SNCs-Pickering emulsions proved to be more proficient in protecting and prolonging the biological activity of curcumin due to their smaller size and better interfacial properties. These findings demonstrated the potential of SNCs for application in Pickering emulsion and delivery of bioactive components.

Starch spectra of Ampelopteris prolifera (Retz.) Copel, a new addition to the existing lexicon and its comparison with a local potato cultivar (Solanum tuberosum L. cv. Kufri Jyoti)

Novel kinds of starch spectra were generated from a lesser-known plant, making this investigation unique. The recent trend of starch characterization shows the establishment of novel bioresources from nonconventional unexplored databases. The present endeavor was made to obtain the starch fingerprint of Ampelopteris prolifera (rhizome) belonging to seedless vascular plants. For comparison, a commercial local cultivar of potato (Kufri Jyoti) was taken. The starch particle of A. prolifera shows much uniqueness depicting its novelty viz., crystallinity index of 60.04 %, powder diffractogram at (2θ scale)17.57° to 39.78°; this diffractogram pattern is reported from this study as newer one i.e. R type(whereas potato starch is CB type); characteristic peak at 2θ = 20.07° suggests starch-lipid complex formation and V type crystallinity (i.e. RS 5 type); FTIR spectra showing the presence of more short chain branching; high gelatinization temperature(84.62 ± 0.10), particle size and zeta value of A. prolifera is 4.00 ± 0.81 μm and - 18.91 ± 3.58 mV respectively. Bragg's peak from the single crystal X-ray diffraction has been generated for the first time of A. prolifera. Extraction of the starch particle was performed in chilled water. Therefore, the present study suggests wide-spectrum commercial utility and cost-effective production.

Recent advances in starch-based coatings for the postharvest preservation of fruits and vegetables

Efficient and low-cost postharvest preservation of fruits and vegetables has always been one of the urgent problems to be solved in the food field. Due to the wide sources, good environmental and human safety, and high biodegradability, starch-based coating preservation method has great application prospects in the postharvest preservation of fruits and vegetables. However, starch materials also have the disadvantages of poor mechanical properties and easy water absorption performance, which makes it difficult to fully meet the requirements in practical production. Therefore, starch is often used in combination with other components to form composite materials. This paper began with an introduction to the preservation principles of edible starch-based coatings, including inherent properties and extra functional properties. Besides, the preservation principles of edible coatings and the recent advances in the field of fruit and vegetable preservation were also comprehensively reviewed, focusing on the preparation and application of starch-based coatings. The information will contribute to the further development of starch-based coatings to improve the postharvest preservation effect of fruits and vegetables.

Comprehensive review on single and dual modification of starch: Methods, properties and applications

Starch is a natural, renewable, affordable, and easily available polymer used as gelling agents, thickeners, binders, and potential raw materials in various food products. Due to these techno-functional properties of starch, food and non-food industries are showing interest in developing starch-based food products such as films, hydrogels, starch nanoparticles, and many more. However, the application of native starch is limited due to its shortcomings. To overcome these problems, modification of starch is necessary. Various single and dual modification processes are used to improve techno-functional, morphological, and microstructural properties, film-forming capacity, and resistant starch. This review paper provides a comprehensive and critical understanding of physical, chemical, enzymatic, and dual modifications (combination of any two single modifications), the effects of parameters on modification, and their applications. The sequence of modification plays a key role in the dual modification process. All single modification methods modify the physicochemical properties, crystallinity, and emulsion properties, but some shortcomings such as lower thermal, acidic, and shear stability limit their application in industries. Dual modification has been introduced to overcome these limitations and maximize the effectiveness of single modification.

Electron beam irradiation-assisted prepare pea starch nanocrystals and characterization of their molecular structure, physicochemical and rheological properties

Electron beam irradiation (EBI) is an environmentally friendly physical modification technology. In this study, pea starch nanocrystals (SNC) were prepared by EBI-assisted pretreatment, and investigated the effects of EBI on the multiscale structure and physicochemical properties of SNC. EBI-assisted pretreatment didn't change the particle morphology, crystalline type and FT-IR spectra of SNC. However, EBI-SNC's relative crystallinity and short-range orderliness index (R1047/1022) significantly increased with increasing irradiation dose (5 KGy-20 KGy). In addition, EBI-assisted pretreatment caused the long chains of SNC's amylopectin to break into short chains. Moreover, EBI-assisted treatment significantly reduced the mean size, molecular weight, apparent amylose content, swelling power and SDS + RS content of SNC, while increasing the solubility, zeta potential and RDS content. Furthermore, the flow properties of the EBI-SNC samples were increased. The results show that EBI effectively changed the structural and functional properties of SNC, and the excellent functional properties are expected to broaden the application range of SNC.

Recent preparation, modification and application progress of starch nanocrystals: A review

Due to the advantages of wide sources, high biocompatibility and favorable biodegradability, starch nanocrystals (SNCs) have gradually attracted attention and have bright development prospects in food, agriculture, materials, medicine and other fields. However, the traditional preparation method of SNCs is time-consuming and inefficient, and the physicochemical properties cannot fully meet the needs of multiple applications. Fortunately, the unique onion-like structure of starch granules and the large number of hydroxyl groups present on the surface entitle SNCs to efficient preparation and modification. This paper comprehensively reviewed the improvement methods of SNCs preparation process in recent years, and the advantages and disadvantages of the two improvement strategies were compared. Besides, the importance of introducing different pretreatment methods into the SNCs preparation process was emphasized. It also focused on the different modification treatment and application progress of SNCs, especially in the starch-based surface coating of fruits and vegetables. The information will contribute to further improve the preparation efficiency and physicochemical properties of SNCs, and ultimately expand the application field.

A Review on Reinforcements and Additives in Starch-Based Composites for Food Packaging

The research of starch as a matrix material for manufacturing biodegradable films has been gaining popularity in recent years, indicating its potential and possible limitations. To compete with conventional petroleum-based plastics, an enhancement of their low resistance to water and limited mechanical properties is essential. This review aims to discuss the various types of nanofillers and additives that have been used in plasticized starch films including nanoclays (montmorillonite, halloysite, kaolinite, etc.), poly-saccharide nanofillers (cellulose, starch, chitin, and chitosan nanomaterials), metal oxides (titanium dioxide, zinc oxide, zirconium oxide, etc.), and essential oils (carvacrol, eugenol, cinnamic acid). These reinforcements are frequently used to enhance several physical characteristics including mechanical properties, thermal stability, moisture resistance, oxygen barrier capabilities, and biodegradation rate, providing antimicrobial and antioxidant properties. This paper will provide an overview of the development of starch-based nanocomposite films and coatings applied in food packaging systems through the application of reinforcements and additives.

Recent advances in access to overcome cancer drug resistance by nanocarrier drug delivery system

Cancer is currently one of the most intractable diseases causing human death. Although the prognosis of tumor patients has been improved to a certain extent through various modern treatment methods, multidrug resistance (MDR) of tumor cells is still a major problem leading to clinical treatment failure. Chemotherapy resistance refers to the resistance of tumor cells and/or tissues to a drug, usually inherent or developed during treatment. Therefore, an urgent need to research the ideal drug delivery system to overcome the shortcoming of traditional chemotherapy. The rapid development of nanotechnology has brought us new enlightenments to solve this problem. The novel nanocarrier provides a considerably effective treatment to overcome the limitations of chemotherapy or other drugs resulting from systemic side effects such as resistance, high toxicity, lack of targeting, and off-target. Herein, we introduce several tumor MDR mechanisms and discuss novel nanoparticle technology applied to surmount cancer drug resistance. Nanomaterials contain liposomes, polymer conjugates, micelles, dendrimers, carbon-based, metal nanoparticles, and nucleotides which can be used to deliver chemotherapeutic drugs, photosensitizers, and small interfering RNA (siRNA). This review aims to elucidate the advantages of nanomedicine in overcoming cancer drug resistance and discuss the latest developments.

Rapid preparation of starch nanocrystals by the mixed acid of sulfuric acid and hydrochloric acid

In this work, waxy maize starch nanocrystals were prepared by mixed acid of sulfuric acid and hydrochloric acid for the first time. Physicochemical properties, crystalline structure, and particle size of starch nanocrystals prepared by mixed acid (HSNC) were measured. The results showed that there was no difference in particle morphology, group structure, and surface elements of HSNC and starch nanocrystals prepared by sulfuric acid (SNC), which was a conventional preparation method. The yield of HSNC was lower than that of SNC. However, the preparation time of HSNC was greatly shortened to 1 h which is only 0.83 % of the time (5 d) to prepare SNC by the sulfuric acid, and HSNC showed higher relative crystallinity and smaller size than those of SNC. In addition, when the ratio of sulfuric acid and hydrochloric acid to provide H ion concentration was 1:1 to hydrolyze starch for >1 h, the crystal pattern of HSNC would be changed to V-typed, while the crystal pattern of SNC was still A-typed. Thus, this work provided efficient method for preparing starch nanocrystals is provided, which can replace sulfuric acid hydrolysis to prepare SNC.

A Comprehensive Study on Starch Nanoparticle Potential as a Reinforcing Material in Bioplastic

Starch can be found in the stems, roots, fruits, and seeds of plants such as sweet potato, cassava, corn, potato, and many more. In addition to its original form, starch can be modified by reducing its size. Starch nanoparticles have a small size and large active surface area, making them suitable for use as fillers or as a reinforcing material in bioplastics. The aim of reinforcing material is to improve the characteristics of bioplastics. This literature study aims to provide in-depth information on the potential use of starch nanoparticles as a reinforcing material in bioplastic packaging. This study also reviews starch size reduction methods including acid hydrolysis, nanoprecipitation, milling, and others; characteristics of the nano-starch particle; and methods to produce bioplastic and its characteristics. The use of starch nanoparticles as a reinforcing material can increase tensile strength, reduce water vapor and oxygen permeability, and increase the biodegradability of bioplastics. However, the use of starch nanoparticles as a reinforcing material for bioplastic packaging still encounters obstacles in its commercialization efforts, due to high production costs and ineffectiveness.

The physical, mechanical, thermal and barrier properties of starch nanoparticle (SNP)/polyurethane (PU) nanocomposite films synthesised by an ultrasound-assisted process

This article reports on the ultrasound-assisted acid hydrolysis for the synthesis and evaluation of starch nanoparticles (SNP) as nanofillers to improve the physical, mechanical, thermal, and barrier properties of polyurethane (PU) films. During the ultrasonic irradiation, dropwise addition of 0.25 mol L^-1 H₂SO₄ was carried out to the starch dispersion for the preparation of SNPs. The synthesized SNPs were blended uniformly within the PU matrix using ultrasonic irradiation (20 kHz, 220 W pulse mode). The temperature was kept constant during the synthesis (4 °C). The nanocomposite coating films were made with a regulated thickness using the casting method. The effect of SNP content (wt%) in nanocomposite coating films on various properties such as morphology, water vapour permeability (WVP), glass transition temperature (Tg), microbial barrier, and mechanical properties was studied. The addition of SNP to the PU matrix increased the roughness of the surface, and Tg by 7 °C, lowering WVP by 60% compared to the PU film without the addition of SNP. As the SNP concentration was increased, the opacity of the film increased. The reinforcement of the SNP in the PU matrix enhanced the microbial barrier of the film by 99.9%, with the optimal content of SNP being 5%. Improvement in the toughness and barrier properties was observed with an increase in the SNP content of the film.

Characterization of acid hydrolysis based nano-converted mung bean (Vigna radiata L.) starch for morphological, rheological and thermal properties

Mung bean starch nanocrystals (SNC) were fabricated using acid hydrolysis. The resulting nanocrystals were studied for their morphological, thermal, and rheological properties. Irregular or round-shaped nano-scale crystals with average hydrodynamic diameter of 179 nm obtained after acid hydrolysis. The mung bean SNC revealed a C_B-type crystalline pattern with enhanced crystallinity as studied by X-ray diffraction (XRD). Lower negative zeta potential was obtained for mung bean SNC as compared to its native starch. Thermal peaks disappeared for nanocrystals, which indicated an increased thermal instability of mung bean SNC. A shear-thinning behavior, even at high concentrations of SNC in the suspension was noticed. The elastic behavior was observed at all studied concentrations and it was independent of the frequency change.

Acid Hydrolysis and Optimization Techniques for Nanoparticles Preparation: Current Review

Nanostarch is unique in that it is highly soluble, thermally stable, non-toxic and inexpensive. Hence, it is utilized in numerous well-established applications, including drug delivery, cosmetics, textiles, foods, and enhanced oil recovery (EOR). These applications take advantage of the special functions that can be achieved through modifications to the structure and properties of native starch. The most common method for the preparation of nanostarch with a relatively higher crystallinity and stability is acid hydrolysis. Technically, the properties of nanostarch are highly dependent on several factors during the hydrolysis process, such as the acid, concentration of acid, reaction time, reaction temperature, and source of starch. The production of nanostarch with desired properties requires a detailed understanding on each of the factors as they are inevitably affected the physical and chemical properties of nanostarch. Hence, it is vital to incorporate optimization technique into the production process to achieve the full potential of nanostarch. Therefore, the current review comprehensively elaborates on the factors that affect acid hydrolysis as well as the optimization techniques used in the preparation of nanostarch.

Mechanochemical Transformations of Biomass into Functional Materials

Biomass is one of the promising alternatives to petroleum-derived materials and plays a major role in our fight against climate change by providing renewable sources of chemicals and materials. Owing to its chemical and structural complexity, the transformation of biomass into value-added products requires a profound understanding of its composition at different scales and innovative methods such as combining physical and chemical processes. In this context, the use of mechanochemistry in biomass valorization is currently growing owing to its potentials as an efficient, sustainable, and environmentally friendly approach. This review highlights the latest advances in the transformation of biomass (i. e., chitin, cellulose, hemicellulose, lignin, and starch) to functional materials using mechanochemical-assisted methods. We focused here on the methodology of biomass processing, influencing factors, and resulting properties with an emphasis on achieving functional materials rather than breaking down the biopolymer chains into smaller molecules. Opportunities and limitations associated this methodology were discussed accordingly for future directions.

Effects of Colloid Milling and Hot-Water Pretreatment on Physical Properties and Enzymatic Digestibility of Oak Wood

A two-step process using colloid milling (CM) and hot water (HW) treatment was evaluated for its ability to improve xylose recovery and the enzymatic digestibility of oak wood. In the first step, CM pretreatment was applied at a milling (feeding) speed of 100 mL/min with four different milling times (3, 6, 9, and 12 h), and the enzymatic digestibility and physical properties of each substrate were measured. In the second-step, the HW pretreatment was applied to enhance the enzymatic digestibility and xylan recovery at various reaction severities (Log R0) from 2.07 to 4.43 using 12 h colloid-milled (CM-treated) oak wood. Compared with untreated oak wood, CM not only significantly disrupted the structure of oak wood but also increased its Brunauer–Emmett–Teller surface area (42-fold) and pore volume (28-fold). The crystallinity of two-step-treated oak wood was decreased to 34.8, while the enzymatic digestibility of 12 h CM-treated oak wood was increased to 58.1% at enzyme loading of 30 filter paper units (FPU)/g glucan for 96 h. After HW treatment of CM-treated oak wood at Log R0 = 3.83, 80.7% of xylan recovery yield and 91.1% of enzymatic digestibility (with 15 FPU/g glucan at 96 h) was obtained, which was 84.2% higher than the enzymatic digestibility of untreated oak wood (6.9%).

Preparing potato starch nanocrystals assisted by dielectric barrier discharge plasma and its multiscale structure, physicochemical and rheological properties

Non-thermal plasma has increasingly been used for surface modification of various materials as a novel green technology. In this study, we prepared potato starch nanocrystals (SNCs) assisted by dielectric barrier discharge plasma technology and investigated its multiscale structure, physicochemical properties and rheology. Plasma treatment did not change the morphology and crystalline pattern of SNCs but reduced the crystallinity. The amylose content, swelling power, gelatinization temperature, and apparent viscosity of SNCs decreased after the plasma process by depolymerizing the amylopectin branch chains and degrading SNCs molecules. Besides, plasma increased the rapidly digestible starch and resistant starch content. Changes in rheological properties of plasma treated SNCs suggested that the plasma process increased the flowing capacity. The effective structural and functional changes of plasma treated SNCs confirm that plasma technology has great potential for modification of SNCs.

Ferulic acid loaded pickering emulsions stabilized by resistant starch nanoparticles using ultrasonication: Characterization, in vitro release and nutraceutical potential

The use of starch based nanoparticles have gained momentum in stabilizing pickering emulsions for it's numerous advantages. In present study resistant starch (RS) was isolated from lotus stem using enzymatic digestion and subjected to nanoprecipitation and ultrasonication to yield resistant starch nanoparticles (RSN). RSN of varying concentrations (2%, 10% and 20%) were used to stabilize the flax seed-oil water mixture to form pickering emulsions. The emulsions were used to nanoencapsulate ferulic acid (FA) - a well known bioactive via ultrasonication. The emulsions were lyophilized to form FA loaded lyophilized pickering emulsion (FA-LPE). The FA-LPE (2%, 10 % and 20%) were characterized using dynamic light scattering (DLS), light microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM) and attenuated total reflectance fourier transform infra-spectroscopy (ATR-FTIR). AFM showed FA-LPE as spherical droplets embedded in the matrix with maximum peak height of 8.47 nm and maximum pit height of 1.69 nm. SEM presented FA-LPE as an irregular and continuous surface having multiple folds and holes. The ATR-FTIR spectra of all the samples displayed peaks of C = C aromatic rings of FA at 1600 cm^-1 and 1439 cm^-1, signifying successful encapsulation. In vitro release assay displayed more controlled release of FA from FA-LPE (20%). Bioactivity of FA-LPE was evaluated in terms of anti-cancer, anti-diabetic, angiotensin converting enzyme (ACE) inhibition and prevention against oxidative damage under simulated gastro-intestinal conditions (SGID). The bioactivity of FA-LPE (20%) was significantly higher than FA-LPE (2%) and FA-LPE (10%). Key findings reveal that pickering emulsions can prevent FA under harsh SGID conditions and provide an approach to facilitate the design of pickering emulsions with high stability for nutraceutical delivery in food and supplement products.

Nonthermal physical modification of starch: An overview of recent research into structure and property alterations

To tailor the properties and enhance the applicability of starch, various ways of starch modification have been practiced. Among them, physical modification methods (micronization, nonthermal plasma, high-pressure, ultrasonication, pulsed electric field, and γ-irradiation) are highly potential for starch modification considering its safety, environmentally friendliness, and cost-effectiveness, without generating chemical wastes. Thus, this article provides an overview of the recent advances in nonthermal physical modification of starch and summarizes the resulting changes in the multi-level structures and physicochemical properties. While the effect of these techniques highly depends on starch type and treatment condition, they generally lead to the destruction of starch granules, the degradation of molecules, decreases in crystallinity, gelatinization temperatures, and viscosity, increases in solubility and swelling power, and an increase or decrease in digestibility, to different extents. The advantages and shortcomings of these techniques in starch processing are compared, and the knowledge gap in this area is commented on.

New Techniques in Structural Tailoring of Starch Functionality

Inherent characteristics of native starches such as water insolubility, retrogradation and syneresis, and instability in harsh processing conditions (e.g., high temperature and shearing, low pH) limit their industrial applications. As starch properties mainly depend on starch composition and structure, structural tailoring of starch has been important for overcoming functional limitations and expanding starch applications in different fields. In this review, we first introduce the basics of starch structure, properties, and functionalities and then describe the interactions of starch with lipids, polysaccharides, and phenolics. After reviewing genetic, chemical, and enzymatic modifications of starch, we describe current progress in the areas of porous starch and starch-based nanoparticles. New techniques, such as using the CRISPR-Cas9 technique to tailor starch structures and using an emulsion-assisted approach in forming functional starch nanoparticles, are only feasible when they are established based on fundamental knowledge of starch. Expected final online publication date for the Annual Review of Food Science and Technology, Volume 13 is March 2022. Please see http://www.annualreviews.org/page/journal/pubdates for revised estimates.

Application of starch-based nanoparticles and cyclodextrin for prebiotics delivery and controlled glucose release in the human gut: a review

Starches are a major constituent of staple foods and are the main source of energy in the human diet (55-70%). In the gastrointestinal tract, starches are hydrolyzed into glucose by α-amylase and α-glucosidase, which leads to a postprandial glucose elevation. High levels of blood glucose levels over sustained periods may promote type 2 diabetes mellitus (T2DM) and obesity. Increasing consumption of starchy foods with a lower glycemic index may therefore contribute to improved health. In this paper, the preparation and properties of several starch-based nanoparticles (SNPs) and cyclodextrins (CDs) derivatives are reviewed. In particular, we focus on the various mechanisms responsible for the ability of these edible nanomaterials to modulate glucose release and the gut microbiome in the gastrointestinal tract. The probiotic functions are achieved through encapsulation and protection of prebiotics or bioactive components in foods or the human gut. This review therefore provides valuable information that could be used to design functional foods for improving human health and wellbeing.

Resistant starch type 2 from lotus stem: Ultrasonic effect on physical and nutraceutical properties

Resistant starch type 2 (RS) was isolated from lotus stem using enzymatic digestion method. The isolated RS was subjected to ultrasonication (US) at different sonication power (100-400 W). The US treated and untreated RS samples were characterized using dynamic light scattering (DLS), scanning electron microscopy (SEM), light microscopy and Fourier transform infrared spectroscopy (FT-IR). DLS revealed that particle size of RS decreased from 12.80 µm to 413.19 nm and zeta potential increased from -12.34 mV to -26.09 mV with the increase in sonication power. SEM revealed smaller, disintegrated and irregular shaped RS particles after ultrasonication. FT-IR showed the decreased the band intensity at 995 cm-1 and 1047 cm-1 signifying that US treatment decreased the crystallinity of RS and increased its amorphous character. The bile acid binding, anti-oxidant and pancreatic lipase inhibition activity of samples also increased significantly (p < 0.05) with the increase in sonication power. Increase in US power however increased the values of hydrolysis from 23.11 ± 1.09 to 36.06 ± 0.13% and gylcemic index from 52.39 ± 0.38 to 59.50 ± 0.11. Overall, the non-thermal process of ultrasonic treatment can be used to change the structural, morphological and nutraceutical profile of lotus stem resistant starch which can have great food and pharamaceutical applications.

Nanostarch: Preparation, Modification, and Application in Pickering Emulsions

Nanostarch, as a food-grade Pickering emulsion stabilizer, has attracted wide attention owing to its biodegradability, nontoxicity, small size, and large specific surface area. In this review, the preparation, modification, and application of Pickering emulsions incorporating nanostarch are described. At present, methods for nanostarch preparation mainly include acid hydrolysis, acid hydrolysis combined with other treatments, nanoprecipitation, ultrasonication, ball milling, and cross-linking. Nanostarch is a promising Pickering emulsion stabilizer, and its emulsifying ability of nanostarch is significantly improved by hydrophobic modification. The hydrophobicity, charge, size, and content of nanostarch affect the emulsion stability. Future developments in this area of research include the efficient and environmentally friendly preparation of nanostarch as well as the control of its hydrophobicity via modification. Future studies should focus on the digestibility and storage stability of Pickering emulsions stabilized by nanostarch under different conditions.

Formation and characterization of mechanochemically generated free lignin radicals from olive seeds

In this study, formation and quantification of mechanochemically generated free radicals of lignin were evaluated after the extraction of lignin from olive seeds and detailed lignin characterization was performed. Lignin was extracted from crushed olive seeds as an insoluble solid using Klason method. Isolated lignin was mechanochemically grinded under cryo conditions using Cryomill and particlesizes were determined by using Zeta Sizer, structural changes were followed by XRD and FTIR-ATR; thermal stabilities were tracked by TGA and DSC. In order to enable solubility demanding studies (such as ¹H‑NMR and GPC), acylation of lignin was accomplished. ESR measurements were completed to prove the nature of the radicals. Free radicals cavenging activity of olive seed lignin was determined and quantified using 2-diphenyl-1-picrylhydrazyl (DPPH) method. Number of created mechanoradicals (per gram of olive seed lignin) was calculated from the corresponding UV‑Vis spectra. Finally, morphological changes of the lignin over cryomilling was evaluated using SEM.

Novel approach on the synthesis of starch betainate by transesterification

Transesterification of starch with methyl betainate was studied for the first time, both in aprotic media and in solid state, and both under alkaline and acidic conditions. Betaine hydrochloride was first esterified in methanol, attaining a conversion of 86%. Starch was then converted into starch betainate in either N,N-dimethylformamide or dimethyl sulfoxide, and using sulfuric acid as catalyst or pre-activating the polymer in NaOH/ethanol. Furthermore, solid-state transesterification was carried out in a ball mill, for which sulfuric acid was replaced with the less corrosive sulfamic acid. Cationic starch esters were characterised by ¹H and ¹³C NMR spectroscopy, infrared spectroscopy, thermogravimetric analysis, viscometry, optical microscopy (in water) and scanning electron microscopy (dry). In solution, the process attained degrees of substitution up to 0.4. No by-products, dehydration, oxidation or colouring were detected, but starch underwent severe depolymerization in wet media. In solid state, whilst the resulting degree of substitution was lower, degradation was minimal. In any case, transesterification, with its variety of possibilities, yields cationic starches that offer a promising alternative to conventional ethers.

Synthesis of Starch Nanoparticles and Their Applications for Bioactive Compound Encapsulation

In recent years, starch nanoparticles (SNPs) have attracted growing attention due to their unique properties as a sustainable alternative to common nanomaterials since they are natural, renewable and biodegradable. SNPs can be obtained by the breakdown of starch granules through different techniques which include both physical and chemical methods. The final properties of the SNPs are strongly influenced by the synthesis method used as well as the operational conditions, where a controlled and monodispersed size is crucial for certain bioapplications. SNPs are considered to be a good vehicle to improve the controlled release of many bioactive compounds in different research fields due to their high biocompatibility, potential functionalization, and high surface/volume ratio. Their applications are frequently found in medicine, cosmetics, biotechnology, or the food industry, among others. Both the encapsulation properties as well as the releasing processes of the bioactive compounds are highly influenced by the size of the SNPs. In this review, a general description of the different types of SNPs (whole and hollow) synthesis methods is provided as well as on different techniques for encapsulating bioactive compounds, including direct and indirect methods, with application in several fields. Starches from different botanical sources and different bioactive compounds are compared with respect to the efficacy in vitro and in vivo. Applications and future research trends on SNPs synthesis have been included and discussed.

Pharmaceutical applications of starch nanoparticles: A scoping review

Starch nanoparticles (SNPs) have been applied to different areas of material sciences, especially in pharmaceuticals due to their characteristics such as small particle size, high surface ratio-volume, and biological compatibility. However, in pharmaceutical sciences, there are no records of a scoping review that had extensively mapped all available information about SNPs. A scoping review was performed here by searching electronic databases (Pubmed and Science Direct) to identify studies published previous to June 2020. From 699 total records, 37 matched the criteria for inclusion. The findings showed that SNPs have been used, not only for the development of different active pharmaceutical ingredient delivery systems, but also as an enzyme inhibitor, adsorption, and DNA precipitation agent. In conclusion, by combining different starch sources and methods SNPs show a remarkable diversity in pharmaceutical applications. Future studies should explore SNPs safety and provide information about variables that may affect important properties for this kind of application.

Polysaccharides-based bio-nanostructures and their potential food applications

Polysaccharides are omnipresent biomolecules that hold great potential as promising biomaterials for a myriad of applications in various biotechnological and industrial sectors. The presence of diverse functional groups renders them tailorable functionalities for preparing a multitude of novel bio-nanostructures. Further, they are biocompatible and biodegradable, hence, considered as environmentally friendly biopolymers. Application of nanotechnology in food science has shown many advantages in improving food quality and enhancing its shelf life. Recently, considerable efforts have been made to develop polysaccharide-based nanostructures for possible food applications. Therefore, it is of immense importance to explore literature on polysaccharide-based nanostructures delineating their food application potentialities. Herein, we reviewed the developments in polysaccharide-based bio-nanostructures and highlighted their potential applications in food preservation and bioactive "smart" food packaging. We categorized these bio-nanostructures into polysaccharide-based nanoparticles, nanocapsules, nanocomposites, dendrimeric nanostructures, and metallo-polysaccharide hybrids. This review demonstrates that the polysaccharides are emerging biopolymers, gaining much attention as robust biomaterials with excellent tuneable properties.

Pearl millet grain as an emerging source of starch: A review on its structure, physicochemical properties, functionalization, and industrial applications

Pearl millet (Pennisetum glaucum (L.) R.Br.) is a sustainable and underutilized starch source, constituting up to 70 % starch in its grain. Pearl millet could be used as a cheaper source of starch as compared to other cereals for developing functional foods. This review is mainly focused on isolation methods, and chemical composition of the pearl millet starch (PMS). Techno-functional characteristics such as; gelatinization, pasting properties, solubility, swelling power, and digestibility to infer wider application of the PMS critically highlighted in the review. Native starches have limited functionalitiesfor food applications due to the instability in developed pastes and gels. A number of modifications (physical, mechanical and enzymatic) have been developed to increase the functionality and to obtain desired characteristics of PMS thus improving its utilization in food applications. Further, the utilization of native as well as modified PMS is also discussed comprehensively. In addition, a number of recommendations to further improve its functionality and increase its application are also discussed.

The preparation of modified nano-starch and its application in food industry

Starch, which is a carbohydrate polymer with a semicrystalline granular structure, has been the subject of academic research for decades due to its renewable and biodegradable property as well as various applications in food, pharmaceutical and other industries. Nano-starch (NS) is a novel type of starch material with unique physiochemical properties due to its small size. However, the nano-size nature of NS determines its tendency to agglomeration as a natural process to approach a thermodynamically steady state, and the single hydroxyl functional group is also not favorable to its applications in hydrophobic environments. Thus, modified-NS with improved dispersion property, hydrophobicity, and stability is emerging as a new research direction. However, information about modified-NS is sporadic in literature, and a systematic review from its preparation, application, the problem and challenge as well as related health concerns is carried out to further the understanding of modified-NS. It is expected that the theoretical basis and new insight into the development of modified-NS will be improved.

Dual modification of various starches: Synthesis, properties and applications

The problems associated with native starches (NSs) and single modified starches were stated in order to justify dual modification of various starches. Broadly, there are two types of dual modification, i.e., homogeneous dual modification and heterogeneous dual modification. The combination of two physical modifications, e.g., (extrusion/annealing); two chemical modifications, e.g., (succinylation/cross-linking) and two enzymes modification (α-amylase/pullulanase) falls under the former classification and the latter classification is the combination of two of each of the differently stated modifications, e.g., acetylation/annealing, extrusion/succinylation, and microwave-assisted phosphorylation, etc. The classification, synthesis, properties and applications of dually modified starches were discussed. There is an attempt to elucidate the problems of each of the single modification in order to justify dual modifications. In dual modifications, the order of reactions, the reaction conditions, the medium of reaction, and the botanical sources of the various starches are very important parameters.

Engineered Multilayer Microcapsules Based on Polysaccharides Nanomaterials

The preparation of microcapsules composed by natural materials have received great attention, as they represent promising systems for the fabrication of micro-containers for controlled loading and release of active compounds, and for other applications. Using polysaccharides as the main materials is receiving increasing interest, as they constitute the main components of the plant cell wall, which represent an ideal platform to mimic for creating biocompatible systems with specific responsive properties. Several researchers have recently described methods for the preparation of microcapsules with various sizes and properties using cell wall polysaccharide nanomaterials. Researchers have focused mostly in using cellulose nanomaterials as structural components in a bio-mimetic approach, as cellulose constitutes the main structural component of the plant cell wall. In this review, we describe the microcapsules systems presented in the literature, focusing on the works where polysaccharide nanomaterials were used as the main structural components. We present the methods and the principles behind the preparation of these systems, and the interactions involved in stabilizing the structures. We show the specific and stimuli-responsive properties of the reported microcapsules, and we describe how these characteristics can be exploited for specific applications.