Review on recent progress in chitosan-based hydrogels for wastewater treatment application

A novel chitosan/cellulose phosphonate composite hydrogel for ultrafast and efficient removal of Pb(II) and Cu(II) from wastewater

Developing green and high-performance adsorbents to separate heavy metals from wastewater is a challenging task. Biomass hydrogel has the advantages of low cost, renewability, and biodegradability, but it has the problem of low adsorption efficiency. Herein, a novel chitosan/cellulose phosphonate composite hydrogel(CS/MCCP) is fabricated by two steps of reactions including the Phosphorylation reaction and the Mannich reaction. As an excellent chelating group, the phosphonate group greatly enhances the adsorption efficiency of the biomass hydrogel. The CS/MCCP shows ultrafast adsorption rate and excellent adsorption capacity for Pb(II) and Cu(II). The saturated adsorption capacity of Pb(II) and Cu(II) is 211.42 and 74.29 mg·g-1, respectively. The adsorption equilibration time is only 10 min. The adsorption performance of the CS/MCCP is superior to that of the reported cellulose/chitosan hydrogels. Besides, an in-depth analysis of the adsorption mechanism is conducted using X-ray photoelectron spectroscopy(XPS) combined with Density Functional Theory(DFT) calculation. The results reveal that the adsorption mechanism is electrostatic attraction and surface complexation, and there is a synergistic coordination between the phosphonate groups and the amino groups.

Enhanced Sorption and Destruction of PFAS by Biochar-Enabled Advanced Reduction Process

The biochar-enabled advanced reduction process (ARP) was developed for enhanced sorption (by biochar) and destruction of PFAS (by ARP) in water. First, the biochar (BC) was functionalized by iron oxide (Fe3O4), zero valent iron (ZVI), and chitosan (chi) to produce four biochars (BC, Fe3O4-BC, ZVI-chi-BC, and chi-BC) with improved physicochemical properties (specific surface area, pore structure, hydrophobicity, and surface functional groups). Batch sorption experimental results revealed that compared to unmodified biochar, all modified biochars showed greater sorption efficiency, and the chi-BC performed the best for PFAS sorption. The chi-BC was then selected to facilitate reductive destruction and defluorination of PFAS in water by ARP in the UV-sulfite system. Adding chi-BC in UV-sulfite ARP system significantly enhanced both degradation and defluorination efficiencies of PFAS (up to ∼100% degradation and ∼85% defluorination efficiencies). Radical analysis using electron paramagnetic resonance (EPR) spectroscopy showed that sulfite radicals dominated at neutral pH (7.0), while hydrated electrons (eaq-) were abundant at higher pH (11) for the efficient destruction of PFAS in the ARP system. Our findings elucidate the synergies of biochar and ARP in enhancing PFAS sorption and degradation, providing insights into PFAS reductive destruction and defluorination by different reducing radical species at varying pHs.

Recent Advancements in the Field of Chitosan/Cellulose-Based Nanocomposites for Maximizing Arsenic Removal from Aqueous Environment

Water remediation, acknowledged as a significant scientific topic, guarantees the safety of drinking water, considering the diverse range of pollutants that can contaminate it. Among these pollutants, arsenic stands out as a particularly severe threat to human health, significantly compromising the overall quality of life. Despite widespread awareness of the harmful effects of arsenic poisoning, there remains a scarcity of literature on the utilization of biobased polymers as sustainable alternatives for comprehensive arsenic removal in practical concern. Cellulose and chitosan, two of the most prevalent biopolymers in nature, provide a wide range of potential benefits in cutting-edge industries, including water remediation. Nanocomposites derived from cellulose and chitosan offer numerous advantages over their larger equivalents, including high chelating properties, cost-effective production, strength, integrity during usage, and the potential to close the recycling loop. Within the sphere of arsenic remediation, this Review outlines the selection criteria for novel cellulose/chitosan-nanocomposites, such as scalability in synthesis, complete arsenic removal, and recyclability for technical significance. Especially, it aims to give an overview of the historical development of research in cellulose and chitosan, techniques for enhancing their performance, the current state of the art of the field, and the mechanisms underlying the adsorption of arsenic using cellulose/chitosan nanocomposites. Additionally, it extensively discusses the impact of shape and size on adsorbent efficiency, highlighting the crucial role of physical characteristics in optimizing performance for practical applications. Furthermore, this Review addresses regeneration, reuse, and future prospects for chitosan/cellulose-nanocomposites, which bear practical relevance. Therefore, this Review underscores the significant research gap and offers insights into refining the structural features of adsorbents to improve total inorganic arsenic removal, thereby facilitating the transition of green-material-based technology into operational use.

Facile synthesis of eco-friendly alginate-chitosan bio-adsorbent for critical raw materials adsorption: A comprehensive study

Sustainable management of critical raw materials is of paramount importance to ensure a steady supply and reduce environmental impact. The application of newly synthesized and environmentally friendly ALG@CS material as a bio-adsorbent for the effective rare earth elements removal from aqueous solution has been presented. The synthesized material underwent FTIR, XPS, EDX, and SEM analysis to determine its suitability for metal uptake. To evaluate the adsorption capacity of ALG@CS for rare earth elements several factors were taken into consideration. These factors included alginate:chitosan ratios, bead size, pH level, composite mass, interaction time, metal ion concentration, and temperature, being all varied during the batch mode evaluation process. Under the optimal conditions, the maximum adsorption capacities were found to be 145.90 mg La(III)/g, 168.44 mg Ce(III)/g, 132.51 mg Pr(III)/g, 128.40 mg Nd(III)/g, 154.36 mg Sm(III)/g, and 165.10 mg Ho(III)/g. The equilibrium data fits well with non-linear three-parameter Sips and Redlich-Peterson isotherm models. The PSO model finds the highest process suitability. The synthesized ALG@CS bio-adsorbent showed excellent regenerative capacity in ten cycles, making it a suitable adsorbent for rare earth elements uptake. The unique bio-adsorbents combination allows for efficient critical raw materials adsorption providing a promising solution for their recovery and recycling.

Preparation and characterization of cellulose-chitosan/β-FeOOH composite hydrogels for adsorption and photocatalytic degradation of methyl orange

Biopolymer-based hydrogels have received great attention in wastewater treatment due to their excellent properties, e.g., high adsorption capacity, fast kinetics, reusability and ease of operation. In the present work, cellulose-chitosan/β-FeOOH composite hydrogels were prepared via co-dissolution and regeneration process as well as hydrothermal in situ synthesis of β-FeOOH. Effect of β-FeOOH loading on the properties of the composite hydrogels and the removal efficiency of methyl orange (MO) was investigated. Results showed that β-FeOOH was uniformly loaded onto the hydrogel framework, and the nanoporous structure of composite hydrogels could increase not only the effective contact area between β-FeOOH and the pollutants but also the active sites. Moreover, the increased β-FeOOH loading led to the enhanced MO removal rate under light conditions. When the loading time was extended from 6 h to 9 h, the MO removal rate increased by 21%, which can be mainly due to the photocatalytic degradation. In addition, MO removal rate reached 97.75% within 40 min under optimal conditions and attained 80.81% after five repetitions. The trapping experiment and EPR results indicated that the main active species were hydrogel radicals and holes. Consequently, this work provides an effective preparation approach for cellulose-chitosan/β-FeOOH composite hydrogel with high adsorption and photocatalytic degradation, which would hold great promise for wastewater treatment applications.

Enhancing Wastewater Depollution: Sustainable Biosorption Using Chemically Modified Chitosan Derivatives for Efficient Removal of Heavy Metals and Dyes

Driven by concerns over polluted industrial wastewater, particularly heavy metals and dyes, this study explores biosorption using chemically cross-link chitosan derivatives as a sustainable and cost-effective depollution method. Chitosan cross-linking employs either water-soluble polymers and agents like glutaraldehyde or copolymerization of hydrophilic monomers with a cross-linker. Chemical cross-linking of polymers has emerged as a promising approach to enhance the wet-strength properties of materials. The chitosan thus extracted, as powder or gel, was used to adsorb heavy metals (lead (Pb2+) and copper (Cu2+)) and dyes (methylene blue (MB) and crystal violet (CV)). Extensive analysis of the physicochemical properties of both the powder and hydrogel adsorbents was conducted using a range of analytical techniques, including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and scanning electron microscopy (SEM), as well as 1H and 13C nuclear magnetic resonance (NMR). To gain a comprehensive understanding of the sorption process, the effect of contact time, pH, concentration, and temperature was investigated. The adsorption capacity of chitosan powder for Cu(II), Pb(II), methylene blue (MB), and crystal violet (CV) was subsequently determined as follows: 99, 75, 98, and 80%, respectively. In addition, the adsorption capacity of chitosan hydrogel for Cu(II), Pb(II), MB, and CV was as follows: 85, 95, 85, and 98%, respectively. The experimental data obtained were analyzed using the Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. The isotherm study revealed that the adsorption equilibrium is well fitted to the Freundlich isotherm (R2 = 0.998), and the sorption capacity of both chitosan powder and hydrogel was found to be exceptionally high (approximately 98%) with the adsorbent favoring multilayer adsorption. Besides, Dubinin has given an indication that the sorption process was dominated by Van der Waals physical forces at all studied temperatures.

Radiation-Induced Hydrogel for Water Treatment

Along with serving as drug delivery sensors and flexible devices, hydrogels are playing pioneering roles in water purification. Both chemical and radiation methods can produce hydrogels, with the latter method gaining preference for its pure adducts. The water treatment process entails the removal of heavy and toxic metals (above the threshold amount), dyes, and solid wastes from industrial effluents, seawater, and groundwater, as well as sterilization for microorganism destruction. This review analyzed the different types of hydrogels produced by applying various radiations for water treatment. Particularly, we examined the hydrogels created through the application of varying levels of gamma and electron beam radiation from the electron gun and Co-60 sources. Moreover, we discuss the optimized radiation doses, the compositions (monomers and polymers) of raw materials required for hydrogel preparation, and their performance in water purification. We present and predict the current state and future possibilities of radiation-induced hydrogels. We explain and compare the superiority of one radiation method over other radiation methods (UV-visible, X-ray, microwave, etc.) based on water treatment.

Biofilm hydrogel derived from physical crosslinking (self-assembly) of xanthan gum and chitosan for removing Cd2+, Ni2+, and Cu2+ from aqueous solution

This study aimed to fabricate a series of biodegradable hydrogel films by gelating/physically crosslinking a blend of xanthan gum (XG) and chitosan (CS) in various combinations using a facile, green, and low cost solution casting technique. The adsorption of Cd2+, Cu2+ and Ni2+ by the XG/CS biofilm in aqueous solution was studied in batch experiments to determine how the pH of the solution, contact time, dosage of adsorbent, initial metal ion concentration and ionic strength affect its adsorption. A highly pH-dependent adsorption process was observed for three metal ions. A maximum amount of Cd2+, Ni2+, and Cu2+ ions was adsorbable with 50 mg of the adsorbent at pH 6.0 for an initial metal concentration of 50 mg.L-1. An empirical pseudo-second-order model seems to fit the kinetic experimental data reasonably well. It was found that the Langmuir model correlated better with equilibrium isotherm when compared with the Freundlich model. For Cd2+, Ni2+, and Cu2+ ions at 25 °C, the maximum monolayer adsorption capacity was 152.33, 144.79, and 139.71 mg.g-1, respectively. Furthermore, the biofilm was capable of regenerating, allowing metal ions to adsorb and desorb for five consecutive cycles. Therefore, the developed biodegradable film offers the potential for remediation of specified metal ions.

Synthesis of poly(ionic liquid-OH) mediated deacetylated chitin and its hydrogels: A study on their applications in controlled release of paracetamol and urea

Due to the biodegradable and biocompatible nature of chitin and chitosan, they are extensively used in the synthesis of hydrogels for various applications. In this work, deacetylation of chitin is carried out with alkaline poly(dimethyldiallylammonium-hydroxide) that gave a higher amount of water-soluble chitin (with 84 % of the degree of deacetylation = chitosan0.84) compared to deacetylation using NaOH. The water-soluble chitosan0.84 is used as intercalating chains for the preparation of acrylic acid and vinylimidazole-based hydrogels. The quaternization of imidazole groups is done with 1,ω-dibromoalkanes, which sets off the crosslinking in the above polymer network. A set of three chitosan0.84 intercalated hydrogels, namely Cs-C4-hydrogel, Cs-C5-hydrogel, and Cs-C10-hydrogel are prepared bearing butyl, pentyl, and decyl chains as respective crosslinkers. The swell ratios of these intercalated hydrogels are compared with those of non-intercalated hydrogels (C4-hydrogel, C5-hydrogel, and C10-hydrogel). Chitosan0.84 intercalated Cs-C10-hydrogel has excellent swelling properties (2330 % swelling ratio) among six synthesized hydrogels. SEM analysis reveals that decyl crosslinker-bearing hydrogels are highly porous. The multi-functionality of Cs-C10-hydrogel and C10-hydrogel is explored towards -the controlled release of paracetamol/urea, and methyleneblue dye absorption. These studies disclose that chitosan0.84 intercalated hydrogels are showing superior-swelling behavior, high paracetamol/urea loading capacities and better dye entrapment than their non-intercalated counterparts.

A comprehensive review on processing, characteristics, and applications of cellulose nanofibrils/graphene hybrid-based nanocomposites: Toward a synergy between two-star nanomaterials

Nanostructured materials are fascinating since they are promising for intensely enhancing materials' performance, and they can offer multifunctional features. Creating such high-performance nanocomposites via effective and mild approaches is an inevitable requirement for sustainable materials engineering. Nanocomposites, which combine two-star nanomaterials, namely, cellulose nanofibrils (CNFs) and graphene derivatives (GNMs), have recently revealed interesting physicochemical properties and excellent performance. Despite numerous studies on the production and application of such systems, there is still a lack of concise information on their practical uses. In this review, recent progress in the production, modification, properties, and emerging uses of CNFs/GNMs hybrid-based nanocomposites in various fields such as flexible energy harvesting and storage, sensors, adsorbents, packaging, and thermal management, among others, are comprehensively examined and described based on recent investigations. Nevertheless, numerous challenges and gaps need to be addressed to successfully introduce such nanomaterials in large-scale industrial applications. This review will certainly help readers understand the design approaches and potential applications of CNFs/GNMs hybrid-based nanocomposites for which new research directions in this emerging topic are discussed.

Boosting Water Retention in Agriculture: Vine Biochar-Doped Hydrogels' Swelling and Germination Effects

Water scarcity presents a formidable challenge to agriculture, particularly in arid, semiarid, and rainfed settings. In agricultural contexts, hydrogels serve as granular agents for water retention, undergoing considerable expansion upon water exposure. They assume versatile roles encompassing soil-water retention, the dispensation of nutrients and pesticides, seed encapsulation, erosion mitigation, and even food supplementation. This study's objective involves the examination of biochar-infused hydrogels, fashioned by incorporating vine pruning waste-derived biochars, and the assessment of swelling behaviors in various aqueous environments encompassing deionized, tap, and saline water at concentrations of 0.5-1%. Characterizations of the vine-biochars-VB and biochar-incorporated hydrogels-VBHG are executed, with particular attention to their swelling properties across diverse media. As an initial step toward appraising their agricultural relevance, these hydrogels are introduced to a germination medium featuring wheat seeds to discern potential influences on germination dynamics. The maximum swelling capacity of VBHG is recorded in deionized water, tap water at pH 7.0, tap water at pH 9.0, saline water at 0.5%, and saline water at 1%, reaching 352%, 207%, 230%, 522%, and 549%, respectively. Remarkably, the 0.5% VBHG treatment exhibits the most pronounced root elongation. The application of hydrogels in agriculture exhibits promise, particularly within drought-related contexts and potential soilless applications.

Chitosan thermogelation and cascade mineralization via sequential CaCO3 incorporations for wound care

Physically crosslinked hydrogels have shown great potential as excellent and eco-friendly matrices for wound management. Herein, we demonstrate the development of a thermosensitive chitosan hydrogel system using CaCO3 as a gelling agent, followed by CaCO3 mineralization to fine-tune its properties. The chitosan hydrogel effectively gelled at 37 °C and above after an incubation period of at least 2 h, facilitated by the CaCO3-mediated slow deprotonation of primary amine groups on chitosan polymers. Through synthesizing and characterizing various chitosan hydrogel compositions, we found that mineralization played a key role in enhancing the hydrogels' mechanical strength, viscosity, and thermal inertia. Moreover, thorough in vitro and in vivo assessments of the chitosan-based hydrogels, whether modified with mineralization or not, demonstrated their outstanding hemostatic activity (reducing coagulation time by >41 %), biocompatibility with minimal inflammation, and biodegradability. Importantly, in vivo evaluations using a rat burn wound model unveiled a clear wound healing promotion property of the chitosan hydrogels, and the mineralized form outperformed its precursor, with a reduction of >7 days in wound closure time. This study presents the first-time utilization of chitosan/CaCO3 as a thermogelation formulation, offering a promising prototype for a new family of thermosensitive hydrogels highly suited for wound care applications.

Spin-Coating Fabrication Method of PDMS/NdFeB Composites Using Chitosan/PCL Coating

This paper verified the possibility of applying chitosan and/or ferulic acid or polycaprolactone (PCL)-based coatings to polydimethylsiloxane/neodymium-iron-boron (PDMS/NdFeB) composites using the spin-coating method. The surface modification of magnetic composites by biofunctional layers allows for the preparation of materials for biomedical applications. Biofunctional layered magnetic composites were obtained in three steps. The spin-coating method with various parameters (time and spin speed) was used to apply different substances to the surface of the composites. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to analyze the thickness and surface topography. The contact angle of the obtained surfaces was tested. Increasing spin speed and increasing process time for the same speed resulted in decreasing the composite's thickness. The linear and surface roughness for the prepared coatings were approximately 0.2 μm and 0.01 μm, respectively, which are desirable values in the context of biocompatibility. The contact angle test results showed that both the addition of chitosan and PCL to PDMS have reduced the contact angle θ from 105° for non-coated composite to θ~59-88° depending on the coating. The performed modifications gave promising results mainly due to making the surface hydrophilic, which is a desirable feature of projected biomaterials.

Enhanced dye sequestration with natural polysaccharides-based hydrogels: A review

Due to the expansion of industrial activities, the concentration of dyes in water has been increasing. The dire need to remove these pollutants from water has been heavily discussed. This study focuses on the reproducible and sustainable solution for wastewater treatment and dye annihilation challenges. Adsorption has been rated the most practical way of the several decolorization procedures due to its minimal initial investment, convenient utility, and high-performance caliber. Hydrogels, which are three-dimensional polymer networks, are notable because of their potential to regenerate, biodegrade, absorb bulky amounts of water, respond to stimuli, and have unique morphologies. Natural polysaccharide hydrogels are chosen over synthetic ones because they are robust, bioresorbable, non-toxic, and cheaply accessible. This study has covered six biopolymers, including chitosan, cellulose, pectin, sodium alginate, guar gum, and starch, consisting of their chemical architecture, origins, characteristics, and uses. The next part describes these polysaccharide-based hydrogels, including their manufacturing techniques, chemical alterations, and adsorption effectiveness. It is deeply evaluated how size and shape affect the adsorption rate, which has not been addressed in any prior research. To assist the readers in identifying areas for further research in this subject, limitations of these hydrogels and future views are provided in the conclusion.

Selective removal of Hg(II) by chitosan derivative covalently modified with double cross-linking agents abundant in N and S atoms

With rapid industrialization and urbanization, numerous wastewater contains elevated concentration of Hg(II), and its concentration must be reduced to the discharge limit, so as not to cause serious pollution to the environment. In this paper, a modified chitosan adsorbent material, AMT-DMTD-CS (CS = chitosan, AMT = 2-amino-5-mercapto-1,3,4-thiadiazole, DMTD = 1,3,4-thiadiazole-2,5-dithiol) was prepared. FT-IR, XPS, elemental analysis, and FE-SEM confirmed that AMT and DMTD were successfully grafted covalently onto CS, with BET analysis showing a specific surface area of 105.55 m2/g for AMT-DMTD-CS. Adsorption study suggests that the optimal pH environment for AMT-DMTD-CS to adsorb Hg(II) is 4.0, and the saturated uptake capacity reaches 687.17 mg/g at 318 K, even after eight regenerations, the removal is still maintained at 80.06 %. Moreover, the adsorption behavior is in perfect agreement with the pseudo-second order kinetic model and the Langmuir isotherm model. In addition, AMT-DMTD-CS shows quite favorable selectivity for Hg(II) in a variety of co-existing metal ions. According to the FT-IR and XPS analysis of AMT-DMTD-CS-Hg(II), the synergistic complexation of -OH, -NH2, -NH, CN, CS and -SH to Hg(II) is considered as the main reason that leading to the elevated adsorption capacity.

Facile preparation of UiO-66-Lys/PAN nanofiber membrane by electrospinning for the removal of Co(II) from simulated radioactive wastewater

In this study, metal-organic framework (MOF) nanofiber membranes (NFMs) UiO-66-Lys/PAN were prepared by electrospinning using polyacrylonitrile (PAN) as the matrix, UiO-66-NH2 as the filler, and lysine (Lys) as the functional monomer. The membranes were subsequently employed to extract cobalt ions from simulated radioactive wastewater. The findings showed that the best performance of the membrane was obtained with a 3 % MOF content (3%UiO-66-Lys/PAN). Specifically, the pure water flux (PWF) of the 3 % UiO-66-Lys/PAN membrane reached 872 L m-2 h-1 with a cobalt ion retention of 45.4 %. In addition, adsorption experiments indicated that the NFMs had a theoretical maximum adsorption capacity of 41.4 mg/g for cobalt ions. The Langmuir isotherm model and the pseudo-second-order kinetic model were observed in the adsorption process, suggesting that the membrane material showed uniform adsorption of cobalt ions on a monolayer level, with an endothermic absorption process. XPS analysis confirmed that 3%UiO-66-Lys/PAN facilitated the adsorption of cobalt ions through a coordination effect, with the N and O atoms serving as coordinating atoms. Moreover, the material displayed excellent radiation stability even when exposed to doses ranging from 20 to 200 kGy. This study validated the stability of the MOF NFMs under real irradiation with radioactive nuclides (60Co) and demonstrated efficient cobalt ion separation. This study has important practical implications for the treatment and disposal of small volumes of 60Co-containing radioactive wastewater for engineering applications.

Recent advances in the application of magnetic materials for the management of perfluoroalkyl substances in aqueous phases

Perfluoroalkyl substances (PFASs) are a class of artificially synthesised organic compounds extensively used in both industrial and consumer products owing to their unique characteristics. However, their persistence in the environment and potential risk to health have raised serious global concerns. Therefore, developing effective techniques to identify, eliminate, and degrade these pollutants in water are crucial. Owing to their high surface area, magnetic responsiveness, redox sensitivity, and ease of separation, magnetic materials have been considered for the treatment of PFASs from water in recent years. This review provides a comprehensive overview of the recent use of magnetic materials for the detection, removal, and degradation of PFASs in aqueous solutions. First, the use of magnetic materials for sensitive and precise detection of PFASs is addressed. Second, the adsorption of PFASs using magnetic materials is discussed. Several magnetic materials, including iron oxides, ferrites, and magnetic carbon composites, have been explored as efficient adsorbents for PFASs removal from water. Surface modification, functionalization, and composite fabrication have been employed to improve the adsorption effectiveness and selectivity of magnetic materials for PFASs. The final section of this review focuses on the advanced oxidation for PFASs using magnetic materials. This review suggests that magnetic materials have demonstrated considerable potential for use in various environmental remediation applications, as well as in the treatment of PFASs-contaminated water.

Photothermal self-floating aerogels based on chitosan functionalized with polydopamine and carbon nanotubes for removal of arsenic from wastewater

Although wastewater disposal in evaporation ponds may be a cost-effective strategy for wastewater management, it overlooks water recycling and can possibly pose significant threats to the surrounding environment. The development of photothermal materials with functional groups capable of adsorbing toxic contaminants offers a promising opportunity for detoxification and potentially solar-driven recycling of wastewater disposed in evaporation ponds. In this study, ultralight aerogels based on chitosan (Ch), a natural biodegradable polymer, functionalized with mussel-inspired polydopamine (PDA) and carbon nanotubes (CNT) were fabricated through a facile approach and examined for the removal of arsenic from water. Three aerogels, namely chitosan, CNT/Ch, and PDA@CNT/Ch were fabricated and characterized using SEM, FTIR, TGA, XPS, and BET surface area analysis. Adsorption isotherms, thermodynamics, and kinetics were systematically investigated, revealing the feasibility of the fabricated aerogels for arsenic removal from aqueous solutions. The UV-Vis and photothermal analysis indicated excellent light-absorption and light-to-heat conversion performance of the functionalized aerogels. Arsenic adsorption by aerogels occurred rapidly and reached equilibrium within 30 to 60 min and was well-fitted by pseudo second-order kinetics model. The Langmuir model well described the adsorption isotherm, and the maximum adsorption capacities were found to be 31.5, 36.6, and 38.7 mg/g at neutral pH for chitosan, CNT/Ch, and PDA@CNT/Ch, respectively. The adsorption mechanism was studied by FTIR and XPS analysis and the adsorption pathway was evaluated using intraparticle diffusion model. This study broadens the scope of utilizing aerogels for the detoxification and potential recycling of wastewater from diverse sources and effluents disposed in evaporation ponds.

An efficient multi-functional ternary reusable nanocomposite based on chitosan@TiO2@Ag NP immobilized on cellulosic fiber as a support substrate for wastewater treatment

To effectively remove heavy metals, organic contaminants, and pathogenic bacteria from wastewater, an efficient multi-functional ternary nanocomposite based on chitosan (CS), titanium dioxide (TiO2 NP), and silver nanoparticles (Ag NP) was prepared. Different tools were used to confirm the successful synthesis of the CS/TiO2 NP/Ag NP nanocomposite. Then, the CS/TiO2 NP/Ag NPnanocomposite was immobilized on the cellulosic fiber as a support substrate for its easy removal and reuse. On a lab scale, CS/TiO2 NP/Ag NP nanocomposite@cellulosic fiber was used to remove Cu (II) ions, methyl orange (MO), and methylene blue (MB), as well as inhibit microbes. The results demonstrate that the greatest removal of Cu (II) ions was 95 % at a concentration of 50 mg/L, pH 5, a temperature of 25 °C, an agitation speed of 200 rpm with 1 g adsorbent dose, and a contact time of 150 min. The pseudo-second-order model explained the batch adsorption kinetics well, while the Langmuir model explained the adsorption isotherm well with an adsorption capacity of 7.71 mg/g. Adsorption thermodynamic parameters revealed that adsorption is a spontaneous, exothermic, increased randomness, and non-specific chemisorption approach. The photodegradation of MO and MB by CS/TiO2 NP/Ag NP nanocomposite@cellulosic fiber was investigated. The results reveal that at pH 3, the MO dye showed the highest photodegradation percentage (90 %), while the MB dye displayed the highest photodegradation percentage (94 %) at pH 11, after an irradiation time of 120 min under visible light. The rate constants for MO and MB were 0.01218 and 0.01412 min-1, respectively. The results antimicrobial activities showed that the CS/TiO2 NP/Ag NP nanocomposite@cellulosic fiber showed excellent antibacterial activity against S. aureus (95 ± 2 %) and E. coli (93 ± 3 %) as well as good antifungal activity against C. albicans (77 ± 2 %).

Efficacious adsorption of divalent nickel ions over sodium alginate-g-poly(acrylamide)/hydrolyzed Luffa cylindrica-CoFe2O4 bionanocomposite hydrogel

Existing Ni2+ heavy metal ions in an aqueous medium are highly hazardous for living organisms and humans. Therefore, designing low-cost adsorbents with enhanced effectiveness is essential for removing nickel ions to safeguard public health. In this study, a novel green nanocomposite hydrogel was synthesized through the free radical solution and bulk polymerization method, and its capability to remove divalent nickel ions from aqueous media was examined. The bionanocomposite hydrogel named as SA-g-poly(AAm)/HL-CoFe2O4 was produced by grafting polyacrylamide (AAm) onto sodium alginate (SA) in the presence of a magnetic composite recognized as HL-CoFe2O4, where HL represents hydrolyzed Luffa Cylindrica. By employing FT-IR, XRD, VSM, SEM, EDX-Map, BET, DLS, HPLC, and TGA techniques, morphological evaluation and characterization of the adsorbents were carried out. The performance of the adsorption process was studied under varying operational conditions including pH, temperature, contact duration, initial concentration of pollutant ions, and adsorbent dosage. HPLC analysis proved the non-toxic structure of the bionanocomposite hydrogel. The number of unreacted acrylamide monomers within the hydrogel matrix was measured at 20.82 mg/kg. The optimum conditions was discovered to be pH = 6, room temperature, adsorbent dosage of 1 of g.L-1, initial Ni2+ concentration of 10 mg.L-1, and contact time of 100 min, and the maximum adsorption efficiency at optimal state was calculated as 70.09, 90.25, and 93.83 % for SA-g-poly (AAm), SA-g-poly(AAm)/HL, and SA-g-poly(AAm)/HL-CoFe2O4 samples, respectively. Langmuir isotherm model was in good agreement with the experimental data and the maximum adsorption capacity of SA-g-poly(AAm), SA-g-poly(AAm)/HL, and SA-g-poly(AAm)/HL-CoFe2O4 samples was calculated to be 31.37, 43.15, and 45.19 mg.g-1, respectively. The adsorption process, according to kinetic studies, follows a pseudo-second-order kinetic model. Investigations on thermodynamics also demonstrated that the process is exothermic and spontaneous. Exploring the interference effect of co-existing ions showed that the adsorption efficiency has decreased with concentration enhancement of Ca2+ and Na+ cations in aqueous medium. Furthermore, the adsorption/desorption assessments revealed that after 8 consecutive cycles, there had been no noticeable decline in the adsorption effectiveness. Finally, actual wastewater treatment outcomes demonstrated that the bionanocomposite hydrogel successfully removes heavy metal pollutants from shipbuilding industry effluent. Therefore, the findings revealed that the newly fabricated bionanocomposite hydrogel is an efficient, cost-effective, easy-separable, and green adsorbent that could be potentially utilized to remove divalent nickel ions from wastewater.

A review on chitosan/metal oxide nanocomposites for applications in environmental remediation

A cleaner and safer environment is one of the most important requirements in the future. It has become increasingly urgent and important to fabricate novel environmentally-friendly materials to remove various hazardous pollutants. Compared with traditional materials, chitosan is a more environmentally friendly material due to its abundance, biocompatibility, biodegradability, film-forming ability and hydrophilicity. As an abundant of -NH2 and -OH groups on chitosan molecular chain could chelate with all kinds of metal ions efficiently, chitosan-based materials hold great potential as a versatile supporting matrix for metal oxide nanomaterials (MONMs) (TiO2, ZnO, SnO2, Fe3O4, etc.). Recently, many chitosan/metal oxide nanomaterials (CS/MONMs) have been reported as adsorbents, photocatalysts, heterogeneous Fenton-like agents, and sensors for potential and practical applications in environmental remediation and monitoring. This review analyzed and summarized the recent advances in CS/MONMs composites, which will provide plentiful and meaningful information on the preparation and application of CS/MONMs composites for wastewater treatment and help researchers to better understand the potential of CS/MONMs composites for environmental remediation and monitoring. In addition, the challenges of CS/MONM have been proposed.

Efficient removal of ethidium bromide from aqueous solutions using chromatin-loaded chitosan polyvinyl alcohol composites

In this work, a novel chromatin-loaded chitosan polyvinyl alcohol composite was developed as a simple, efficient and environmentally friendly adsorbent for the efficient removal of ethidium bromide (EtBr). SEM images showed that the composites were characterized by dense porous and uniformly distributed morphology. The BET analysis showed the presence of mesopores and macropores in the composites. FTIR and XRD results showed that the chromatin was uniformly dispersed in the chitosan-polyvinyl alcohol carrier through hydrogen bonding. The fluorescence microscopy images showed the change of fluorescence effect before and after the adsorption of the material, which indicated that the chromatin was uniformly distributed in the composites and had a good adsorption effect. The optimal experimental conditions were T = 30℃, t = 120 min, pH = 7.4, m = 0.2 g when the composite with only 5% chromatin content had the ability to adsorb EtBr efficiently (minimum concentration 2 mg·L-1: adsorption rate 99%; maximum concentration 20 mg·L-1: adsorption rate 90%).The adsorption kinetics and thermodynamics showed that the EtBr adsorption kinetics of the composite conformed to the pseudo-second-order kinetic model (0.995 < R2 < 0.999) and the Freundlich isothermal model, and was a spontaneous process (ΔH < 0). This study on the immobilization of chromatin will provide a new way and reference for the application of chromatin in the treatment of EtBr pollutants.

Preparation of chitosan-based ternary nanocomposite hydrogel film by loading graphene oxide nanosheets as adsorbent for enhanced methylene blue dye removal

Our objective in this study is to fabricate a novel chitosan-based ternary nanocomposite hydrogel film by incorporating graphene oxide (GO) nanosheets into a chitosan/partially hydrolyzed polyacrylamide (PHPA) network to boost adsorption efficiency through one step self-assembly process in water. Basically, H-bonding interactions drive the formation of a crosslinking network structure. The Batch adsorption experiments evaluated the hydrogel nanocomposite's MB adsorption performance. By loading GO, surface roughness, swelling percentage (from 21,200 % to 35,800 %), elastic modulus of up to 73.7 Pa, and adsorption characteristics (from 282 mg/g to 468 mg/g) were enhanced. The nanocomposite displayed outstanding thermally/pH responsiveness properties. MB adsorption equilibrium was reached after 45 min and the adsorption capacity was 476.19 mg.g-1 when the initial concentration was 100 mg/L. The MB adsorption kinetics and isotherms by the nanocomposite were well correlated by the PSO and the Langmuir models (R2 > 0.99), respectively. The loaded nanocomposite was shown to be regenerative for five cycles through desorption studies. Thermodynamic analysis indicated that MB adsorption occurred spontaneously (ΔG°: -16.47 kJ/mol, 303 K) and exothermically (ΔH°: -79.49 kJ/mol). A plausible adsorption mechanism was proposed for the nanocomposite developed for MB removal. Our results can contribute to the design and fabrication of nanocomposite adsorbents to treat wastewater.

Cost-effective removal of toxic methylene blue dye from textile effluents by new integrated crosslinked chitosan/aspartic acid hydrogels

Chitosan/aspartic acid hydrogels were synthesized for MB dye removal from textile aqueous effluents with different ratios by gelation of chitosan with non-toxic gelling agent, crosslinker, glutaraldehyde (Glu). The obtained hydrogels were characterized by spectral and morphological techniques. The characterization techniques confirmed successful preparations and MB dye adsorption. Batch experiments were done to investigate the effects of adsorbent dose, pH, contact time, temperature, and initial MB dye concentration. The optimum conditions were: adsorbent dose 0.1 g, pH 5, contact time 30 min, and temperature 25 °C for Chitosan-Aspartic Acid Hydrogel 1 (CSAA-HG1) and adsorbent dose 0.4 g, pH 2, contact time 60 min, temperature 25 °C for Chitosan-Aspartic Acid Hydrogel 2 (CSAA-HG2). Adsorption capacity of newly hydrogels CSAA-HG1,2 was compared with each other. Adsorption efficiencies reached 99.85 % for CSAA-HG1 and 99.88 % for CSAA-HG2. MB dye adsorption on CSAA-HG1,2 followed Freundlich isotherm model (R2 = 0.94 and 0.92, respectively). Both adsorbents exhibited pseudo-second-order kinetics for MB dye adsorption (R2 = 1). The negative ΔHo indicated that the MB dye adsorption was exothermic, negative ΔGo confirmed that MB dye adsorption process was spontaneous and low values of ∆So indicated low degree of freedom, ordered MB dye molecules on CSAA-HG1,2 surfaces.

Prospects of Using Chitosan-Based Biopolymers in the Treatment of Peripheral Nerve Injuries

Peripheral nerve injuries are common neurological disorders, and the available treatment options, such as conservative management and surgical repair, often yield limited results. However, there is growing interest in the potential of using chitosan-based biopolymers as a novel therapeutic approach to treating these injuries. Chitosan-based biopolymers possess unique characteristics, including biocompatibility, biodegradability, and the ability to stimulate cell proliferation, making them highly suitable for repairing nerve defects and promoting nerve regeneration and functional recovery. Furthermore, these biopolymers can be utilized in drug delivery systems to control the release of therapeutic agents and facilitate the growth of nerve cells. This comprehensive review focuses on the latest advancements in utilizing chitosan-based biopolymers for peripheral nerve regeneration. By harnessing the potential of chitosan-based biopolymers, we can pave the way for innovative treatment strategies that significantly improve the outcomes of peripheral nerve injury repair, offering renewed hope and better prospects for patients in need.

Chitosan Hydrogels for Water Purification Applications

Chitosan-based hydrogels have gained significant attention for their potential applications in water treatment and purification due to their remarkable properties such as bioavailability, biocompatibility, biodegradability, environmental friendliness, high pollutants adsorption capacity, and water adsorption capacity. This article comprehensively reviews recent advances in chitosan-based hydrogel materials for water purification applications. The synthesis methods, structural properties, and water purification performance of chitosan-based hydrogels are critically analyzed. The incorporation of various nanomaterials into chitosan-based hydrogels, such as nanoparticles, graphene, and metal-organic frameworks, has been explored to enhance their performance. The mechanisms of water purification, including adsorption, filtration, and antimicrobial activity, are also discussed in detail. The potential of chitosan-based hydrogels for the removal of pollutants, such as heavy metals, organic contaminants, and microorganisms, from water sources is highlighted. Moreover, the challenges and future perspectives of chitosan-based hydrogels in water treatment and water purification applications are also illustrated. Overall, this article provides valuable insights into the current state of the art regarding chitosan-based hydrogels for water purification applications and highlights their potential for addressing global water pollution challenges.

Removal of Phosphate by Adsorption with 2-Phenylimidazole-Modified Porous ZIF-8: Powder and Chitosan Spheres

Due to rapid socioeconomic development, increased phosphorus concentrations can cause eutrophication of water bodies, with devastating effects on environmental sustainability and aquatic ecosystems. In this study, ZIF-8-PhIm was prepared for phosphorus removal using 2-phenylimidazole via the solvent-assisted ligand exchange (SALE) method. The structure and composition of ZIF-8-PhIm were characterized by various methods, including X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), 1H nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) analysis. Compared to the ZIF-8 material, it exhibited a multistage pore structure with larger pore capacity and pore size, increased hydrophilicity, exposure of more adsorption sites, and also stronger electrostatic interaction. Under optimized conditions (T = 298 K, C0 = 150 mg/L, dose = 0.2 g/L), the adsorption capacity of ZIF-8-PhIm reached 162.93 mg/g, which was greater than that of the ZIF-8 material (92.07 mg/g). The Langmuir isotherm and pseudo-second-order kinetic models were suitable for describing the phosphate adsorption of ZIF-8-PhIm. The main effects of ZIF-8-PhIm on phosphate adsorption were Zn-O-P bonding and electrostatic interactions. It also had good regeneration properties. The ZIF-8-PhIm/CS spheres were prepared using chitosan (CS) as the cross-linking agent. The results of dynamic adsorption experiments on the spheres showed a saturation capacity of 85.69 mg/g and a half-penetration time of 514.15 min at 318 K according to the fitted results.

Chitosan Oligomer as a Raw Material for Obtaining Polyurethane Foams

Decreasing oil extraction stimulates attempts to use biologically available sources to produce polyols, which are the basic components for obtaining polyurethane foams. Plants are inexhaustible source of oils, sugars, starches, and cellulose. Similar substrates to obtain polyols are chitosans. Commercially available modified chitosans are soluble in water, which gives them the possibility to react with hydroxyalkylating agents. We used a water-soluble chitosan previously to obtain polyols suitable for producing rigid polyurethane foams. Here, we described hydroxyalkylation of a low-molecular-weight chitosan (oligomeric chitosan) with glycidol and ethylene carbonate to obtain polyols. The polyols were isolated and studied in detail by IR, ¹H-NMR, and MALDI-ToF methods. Their properties, such as density, viscosity, surface tension, and hydroxyl numbers, were determined. The progress of the hydroxyalkylation reaction of water-soluble chitosan and chitosan oligomer with glycidol was compared in order to characterize the reactivity and mechanism of the process. We found that the hydroxyalkylation of chitosan with glycidol in glycerol resulted in the formation of a multifunctional product suitable for further conversion to polyurethane foams with favorable properties. The straightforward hydroxyalkylation of chitosan with glycidol was accompanied by the oligomerization of glycidol. The hydroxyalkylation of chitosan with glycidol in the presence of ethylene carbonate was accompanied by minor hydroxyalkylation of chitosan with ethylene carbonate. The chosen polyols were used to obtain rigid polyurethane foams which were characterized by physical parameters such as apparent density, water uptake, dimension stability, heat conductance, compressive strength, and heat resistance at 150 and 175 °C. The properties of polyurethane foams obtained from chitosan-oligomer and water-soluble-chitosan sources were compared. Polyurethane foams obtained from polyols synthesized in the presence of glycerol had advantageous properties such as low thermal conductivity, enhanced thermal resistance, dimensional stability, low water uptake, and high compressive strength, growing remarkably upon thermal exposure.

Removal of methylene blue by using sodium alginate-based hydrogel; validation of experimental findings via DFT calculations

Removal of commonly used dyes from water bodies has recently gained great interest from the scientific community. Presence of the methylene blue (MB) dye in drinking water poses harmful effects on the human health. The large-scale removal of MB is achievable through highly efficient, inexpensive, renewable, and biodegradable adsorbents. Our research group has recently synthesized a sodium alginate-based hydrogel and explored its application towards the removal of MB. Previous results have shown that the synthesized hydrogel exhibits a high adsorption capacity of 51.34 mg/g under basic conditions. Herein, we employed the density functional theory (DFT) calculations to explore the mechanism of MB removal by using sodium alginate hydrogel at various pH levels. Results of this study have shown that under acidic/neutral conditions the removal of MB is endergonic (ΔG_int = 6.10 kcal/mol). Whereas under basic conditions it is highly exergonic (ΔG_int = -97.58 kcal/mol). Moreover, the QTAIM and NCI analyses have shown that the MB dye is chemisorbed to the absorbent via strong covalent-like interactions between the polymer's carboxylate groups and the hydrogens in MB. Furthermore, preferability of basic conditions have been confirmed by the large charge transfer (0.104 |e|), as compared to no charge being transferred in the acidic/neutral conditions.

Synthesis of New Hydrogels Involving Acrylic Acid and Acrylamide Grafted Agar-Agar and Their Application in the Removal of Cationic Dyes from Wastewater

Polyacrylic Acid grafted Agar-agar (AAc-graf-Agar), and polyacrylamide grafted Agar-Agar (AAm-graf-Agar) have been synthesised by free radical polymerisation route initiated by ammonium peroxodisulphate (APS), the grafted polymers were characterised by FTIR, TGA and SEM methods. The swelling properties were studied in deionised water and saline solution at room temperature. The prepared hydrogels were examined by removing cationic methylene blue (MB) dye from the aqueous solution, in which the adsorption kinetics and isotherms models were also investigated. It was found that the pseudo-second-order and Langmuir equations are the most suitable for the different sorption processes. The maximum dye adsorption capacity was 1035.96 mg∙g^-1 for AAc-graf-Agar in pH medium 12 and 1015.7 mg∙g^-1 for AAm-graf-Agar in neutral pH medium. This indicates that the AAc-graf-Agar hydrogel could be an excellent adsorbent for removing MB from aqueous solutions.

A comprehensive review of chitosan applications in paper science and technologies

Using environmentally friendly biomaterials in different aspects of human life has been considered extensively. In this respect, different biomaterials have been identified and different applications have been found for them. Currently, chitosan, the well-known derivative of the second most abundant polysaccharide in the nature (i.e., chitin), has been receiving a lot of attention. This unique biomaterial can be defined as a renewable, high cationic charge density, antibacterial, biodegradable, biocompatible, non-toxic biomaterial with high compatibility with cellulose structure, where it can be used in different applications. This review takes a deep and comprehensive look at chitosan and its derivative applications in different aspects of papermaking.

Easy separable, floatable, and recyclable magnetic-biochar/alginate bead as super-adsorbent for adsorbing copper ions in water media

This work aimed to develop innovative material by combining properties of magnetic-biochar (derived from peanut shells) and hydrogel bead (MBA-bead) and apply it for adsorbing Cu²⁺ in water. MBA-bead was synthesized by physical cross-linking methods. Results indicated that MBA-bead contained ∼90% water. The diameter of each spherical MBA-bead was approximately 3 mm (wet form) and 2 mm in (dried form). Its specific surface area (262.4 m²/g) and total pore volume (0.751 cm³/g) were obtained from nitrogen adsorption at 77K. X-ray diffraction data confirmed Fe₃O₄ presented in magnetic-biochar and MBA-bead. Its Langmuir maximum adsorption capacity for Cu²⁺ was 234.1 mg/g (30 °C and pH_eq 5.0). The change in standard enthalpy (ΔH°) of the adsorption was 44.30 kJ/mol (dominant physical adsorption). Primary adsorption mechanisms were complexation, ion exchange, and Van der Waals force. Laden MBA-bead can be reused several cycles after desorbing with NaOH or HCl. The cost was estimated for producing PS-biochar (0.091 US$/kg), magnetic-biochar (0.303-0.892 US$/kg), and MBA-bead (1.369-3.865 US$/kg). MBA-bead can serve as an excellent adsorbent for removing Cu²⁺ from water.

Construction of amino-thiol functionalized ion-imprinted chitosan for lead (II) ion removal

Ion-imprinting technique was used to create a lead ion-imprinted sorbent from an amino-thiol chitosan derivative (Pb-ATCS). First, 3-Nitro-4-sulfanylbenzoic acid (NSB) unit's amidized the chitosan, and then the -NO₂-residues were selectively reduced to -NH₂. Imprinting was accomplished by cross-linking with epichlorohydrin and removing the Pb (II) ions from the across-linked polymeric complex formed from the amino-thiol chitosan polymer ligand (ATCS) and Pb (II) ions. The synthetic steps have been investigated by nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR), and the sorbent was tested for its ability to selectively bind Pb (II) ions. The produced Pb-ATCS sorbent had a maximum capacity of roughly 300 mg/g, and it showed a greater affinity for the Pb (II) ions than the control NI-ATCS sorbent particle. The pseudo-2nd-order equation was also consistent with the adsorption kinetics of the sorbent, which were quite rapid. This demonstrated that metal ions were chemo-adsorbed onto the Pb-ATCS and NI-ATCS solid surfaces via coordination with the introduced amino-thiol moieties.

Compressible Cellulose Wood Prepared with Deep Eutectic Solvents and Its Improved Technology

Elastic materials have a wide range of applications in many industries, but their widespread use is often limited by small-scale production methods and the use of highly polluting chemical reagents. In this study, we drew inspiration from research on wood softening to develop an environmentally friendly and scalable approach for producing a new type of compressible wood material called CW from natural wood. To achieve this, we employed a top-down approach using a novel type of “ionic liquid” eutectic solvent (DES) that is cost-effective, environmentally friendly, and recyclable. After treatment with DES, the resulting CW demonstrated good elasticity and durable compressibility, which was achieved by removing some lignin and hemicellulose from the wood and thinning the cell walls, thereby creating a honeycomb structure that allows for sustained compression and rebound. However, we found that the wood treated with a single eutectic solvent showed some softening (CW-1), although there was still room for further improvement of its elasticity. To address this, we used a secondary treatment with sodium hydroxide alkali solution to produce a softer and more elastic wood (CW-2). We conducted a series of comparative analyses and performance tests on natural wood (NW) and CW, including microscopic imaging; determination of chemical composition, mechanical properties, and compressive stress effects; and laser confocal testing. The results show that the DES and sodium hydroxide alkali solution treatments effectively removed some lignin, hemicellulose, and cellulose from the wood, resulting in the thinning of the cell walls and creating a more elastic material with a sustainable compression rebound rate of over 90%. The various properties of CW, including its elasticity, durability, and sustainability, provide great potential for its application in a range of fields, such as sensors, water purification, and directional tissue engineering.

Polyols and Polyurethane Foams Based on Water-Soluble Chitosan

At present, majority of polyols used in the synthesis of polyurethane foams are of petrochemical origin. The decreasing availability of crude oil imposes the necessity to convert other naturally existing resources, such as plant oils, carbohydrates, starch, or cellulose, as substrates for polyols. Within these natural resources, chitosan is a promising candidate. In this paper, we have attempted to use biopolymeric chitosan to obtain polyols and rigid polyurethane foams. Four methods of polyol synthesis from water-soluble chitosan functionalized by reactions of hydroxyalkylation with glycidol and ethylene carbonate with variable environment were elaborated. The chitosan-derived polyols can be obtained in water in the presence of glycerol or in no-solvent conditions. The products were characterized by IR, 1H-NMR, and MALDI-TOF methods. Their properties, such as density, viscosity, surface tension, and hydroxyl numbers, were determined. Polyurethane foams were obtained from hydroxyalkylated chitosan. The foaming of hydroxyalkylated chitosan with 4,4′-diphenylmethane diisocyanate, water, and triethylamine as catalysts was optimized. The four types of foams obtained were characterized by physical parameters such as apparent density, water uptake, dimension stability, thermal conductivity coefficient, compressive strength, and heat resistance at 150 and 175 °C. It has been found that the obtained materials had most of the properties similar to those of classic rigid polyurethane foams, except for an increased thermal resistance up to 175 °C. The chitosan-based polyols and polyurethane foams obtained from them are biodegradable: the polyol is completely biodegraded, while the PUF obtained thereof is 52% biodegradable within 28 days in the soil biodegradation oxygen demand test.

Chitosan as a Canvas for Studies of Macromolecular Controls on CaCO3 Biological Crystallization

A mechanistic understanding of how macromolecules, typically as an organic matrix, nucleate and grow crystals to produce functional biomineral structures remains elusive. Advances in structural biology indicate that polysaccharides (e.g., chitin) and negatively charged proteoglycans (due to carboxyl, sulfate, and phosphate groups) are ubiquitous in biocrystallization settings and play greater roles than currently recognized. This review highlights studies of CaCO₃ crystallization onto chitinous materials and demonstrates that a broader understanding of macromolecular controls on mineralization has not emerged. With recent advances in biopolymer chemistry, it is now possible to prepare chitosan-based hydrogels with tailored functional group compositions. By deploying these characterized compounds in hypothesis-based studies of nucleation rate, quantitative relationships between energy barrier to crystallization, macromolecule composition, and solvent structuring can be determined. This foundational knowledge will help researchers understand composition-structure-function controls on mineralization in living systems and tune the designs of new materials for advanced applications.

Plasma etching effect on the molecular structure of chitosan-based hydrogels and its biological properties

To reasonably use hydrogels in healthcare field, this study four kinds of chitosan (CTS)-based hydrogels with different molecular structures. With plasma etching, the morphology, chemical groups' proportion, and hydrophilicity of the hydrogel surface were changed. At 40 min of modification, the ratios of CO and NH₂ on the CTS40-based hydrogel surface increased and reached their maximum values of 40.31 % and 89.17 %, respectively. Combined with the changes in hydrophilic chemical groups and the hydrogel's network structure, the hydrogel surface's wettability changed after plasma etching. From the results, CTS40-based hydrogel showed the lowest contact angle (77.40 ± 3.89°) with 80 min modification due to its dense network structure of CTS and appropriate ratio of hydrophilic groups on the surface. With these molecular structural changes, the antibacterial properties of CTS-based hydrogels against Staphylococcus aureus were improved. Moreover, the functional components delivery system coating with these CTS-based hydrogels showed colon-site controlled-release property. The hydrogels also facilitated the growth of Caco2 and Hic cells, which had 72.74 %-453.27 % cell viability of Caco2 cells on the surface. Therefore, the antibacterial property and biocompatibility of plasma modified CTS-based hydrogels have been demonstrated. The mechanism between molecular structure changes of CTS with plasma etching and its properties was discussed, which would provide a promising carrier material for utilizing healthcare field.

Development of Tofacitinib Loaded pH-Responsive Chitosan/Mucin Based Hydrogel Microparticles: In-Vitro Characterization and Toxicological Screening

Tofacitinib is an antirheumatic drug characterized by a short half-life and poor permeability, which necessitates the development of sustained release formulation with enhanced permeability potential. To achieve this goal, the free radical polymerization technique was employed to develop mucin/chitosan copolymer methacrylic acid (MU-CHI-Co-Poly (MAA))-based hydrogel microparticles. The developed hydrogel microparticles were characterized for EDX, FTIR, DSC, TGA, X-ray diffraction, SEM, drug loading; equilibrium swelling (%), in vitro drug release, sol–gel (%) studies, size and zeta potential, permeation, anti-arthritic activities, and acute oral toxicity studies. FTIR studies revealed the incorporation of the ingredients into the polymeric network, while EDX studies depicted the successful loading of tofacitinib into the network. The thermal analysis confirmed the heat stability of the system. SEM analysis displayed the porous structure of the hydrogels. Gel fraction showed an increasing tendency (74–98%) upon increasing the concentrations of the formulation ingredients. Formulations coated with Eudragit (2% w/w) and sodium lauryl sulfate (1% w/v) showed increased permeability. The formulations equilibrium swelling (%) increased (78–93%) at pH 7.4. Maximum drug loading and release (%) of (55.62–80.52%) and (78.02–90.56%), respectively, were noticed at pH 7.4, where the developed microparticles followed zero-order kinetics with case II transport. Anti-inflammatory studies revealed a significant dose-dependent decrease in paw edema in the rats. Oral toxicity studies confirmed the biocompatibility and non-toxicity of the formulated network. Thus, the developed pH-responsive hydrogel microparticles seem to have the potential to enhance permeability and control the delivery of tofacitinib for the management of rheumatoid arthritis.

Introducing Semi-Interpenetrating Networks of Chitosan and Ammonium-Quaternary Polymers for the Effective Removal of Waterborne Pathogens from Wastewaters

The present work aims to study the influence of ammonium-quaternary monomers and chitosan, obtained from different sources, upon the effect of semi-interpenetrating polymer network (semi-IPN) hydrogels upon the removal of waterborne pathogens and bacteria from wastewater. To this end, the study was focused on using vinyl benzyl trimethylammonium chloride (VBTAC), a water-soluble monomer with known antibacterial properties, and mineral-enriched chitosan extracted from shrimp shells, to prepare the semi-IPNs. By using chitosan, which still contains the native minerals (mainly calcium carbonate), the study intends to justify that the stability and efficiency of the semi-IPN bactericidal devices can be modified and better improved. The new semi-IPNs were characterized for composition, thermal stability and morphology using well-known methods. Swelling degree (SD%) and the bactericidal effect assessed using molecular methods revealed that hydrogels made of chitosan derived from shrimp shell demonstrated the most competitive and promising potential for wastewater (WW) treatment.

Biopolymer - A sustainable and efficacious material system for effluent removal

Undesired discharge of various effluents directly into the aquatic ecosystem can adversely affect water quality, endangering aquatic and terrestrial flora and fauna. Therefore, the conceptual design and fabrication of a sustainable system for alleviating the harmful toxins that are discharged into the atmosphere and water bodies using a green sustainable approach is a fundamental standpoint. Adsorptive removal of toxins (∼99% removal efficacy) is one of the most attractive and facile approaches for cleaner technologies that remediate the environmental impacts and provide a safe operating space. Recently, the introduction of biopolymers for the adsorptive abstraction of toxins from water has received considerable attention due to their eclectic accessibility, biodegradability, biocompatibility, non-toxicity, and enhanced removal efficacy (∼ 80-90% for electrospun fibers). This review summarizes the recent literature on the biosorption of various toxins by biopolymers and the possible interaction between the adsorbent and adsorbate, providing an in-depth perspective of the adsorption mechanism. Most of the observed results are explained in terms of (1) biopolymers classification and application, (2) toxicity of various effluents, (3) biopolymers in wastewater treatment and their removal mechanism, and (4) regeneration, reuse, and biodegradation of the adsorbent biopolymer.

Synthesis and characterization of hydrogel-based magnetite nanocomposite adsorbents for the potential removal of Acid Orange 10 dye and Cr(VI) ions from aqueous solution

Magnetic responsive hydrogels (CMX-cl-P4VP/M-NPs) were successfully synthesized through in situ co-precipitation procedure and investigated using various techniques. The surface morphology analysis revealed that the M-NPs were uniformly distributed within the hydrogel matrix and had average sizes ranging from 4.98 to 15.02 nm. The graft copolymer containing nanoparticles exhibited a sensitive magnetic response, and their recovery could be facilitated by applying a magnetic field. The purpose of this research is to study the ability of the prepared magnetic hydrogel to remove AO-10 dye and hexavalent chromium ions (Cr(VI)) from the aqueous solution under various factors, namely contact time, pH, amount of adsorbent, coexisting ions and AO-10 and Cr(VI) concentrations. The outcomes of the batch adsorption demonstrated that the adsorbent hydrogel incorporated with a low percentage (10 %) of M-NPs had a strong affinity for the removal of AO-10 dye and Cr(VI) ions at an optimum pH = 3, and the removal percentage reached 99.3 and 97.4 % for 500 mg L^-1 and 300 mg L^-1 of AO-10 dye and Cr(VI) ions within 90, 50 min, respectively. The data were well-fitted by pseudo-first-order kinetics. The maximum adsorption capacities of AO-10 dye and Cr(VI) ions onto adsorbent were 2448 and 574.7 mg g^-1 at 298 K, calculated from the Langmuir model.

Advanced Polymeric Nanocomposite Membranes for Water and Wastewater Treatment: A Comprehensive Review

Nanomaterials have been extensively used in polymer nanocomposite membranes due to the inclusion of unique features that enhance water and wastewater treatment performance. Compared to the pristine membranes, the incorporation of nanomodifiers not only improves membrane performance (water permeability, salt rejection, contaminant removal, selectivity), but also the intrinsic properties (hydrophilicity, porosity, antifouling properties, antimicrobial properties, mechanical, thermal, and chemical stability) of these membranes. This review focuses on applications of different types of nanomaterials: zero-dimensional (metal/metal oxide nanoparticles), one-dimensional (carbon nanotubes), two-dimensional (graphene and associated structures), and three-dimensional (zeolites and associated frameworks) nanomaterials combined with polymers towards novel polymeric nanocomposites for water and wastewater treatment applications. This review will show that combinations of nanomaterials and polymers impart enhanced features into the pristine membrane; however, the underlying issues associated with the modification processes and environmental impact of these membranes are less obvious. This review also highlights the utility of computational methods toward understanding the structural and functional properties of the membranes. Here, we highlight the fabrication methods, advantages, challenges, environmental impact, and future scope of these advanced polymeric nanocomposite membrane based systems for water and wastewater treatment applications.

Adsorption Characteristics for Cu(II) and Phosphate in Chitosan Beads under Single and Mixed Conditions

Chitosan, a natural organic polymer, has shown bifunctional characteristics in the removal of cationic and anionic contaminants from water and wastewater treatment. In particular, cationic Cu(II) and anionic phosphate can simultaneously interact with chitosan owing to the presence of the amino group in the form of NH₂ and NH₃⁺ in chitosan. To gain greater insight into the bifunctional adsorption characteristics of chitosan, its adsorption capacity for Cu(II) and phosphate was tested under single and mixed (co-ion) conditions to investigate the interactions between four types of chitosan beads and NH₂ and NH₃⁺. In the single condition, Cu(II) uptake was reduced from 0.243 to 0.0197 mmol/g due to the crosslinking and drying processes, whereas no significant reduction in phosphate uptake was observed, indicating that the crosslinking agent only interacted with NH₂ to decrease the number of available adsorption sites for Cu(II). Under the mixed condition, the simultaneous presence of the two ions clearly increased the uptake of each other, with the adsorption of phosphate being more influenced than that of Cu(II). The comparison of the rate constant, k₁ or k₂, using pseudo-first- and pseudo-second-order models confirmed that phosphate reached equilibrium faster than Cu(II), suggesting that electrostatic interaction was preferred over coordination. In addition, under mixed conditions, co-ion competition slowed down the adsorption kinetics for both Cu(II) and phosphate.

In Situ Stimulation of Self-Assembly Tunes the Elastic Properties of Interpenetrated Biosurfactant-Biopolymer Hydrogels

Hydrogels are widespread soft materials, which can be used in a wide range of applications. The control over the viscoelastic properties of the gel is of paramount importance. Ongoing environmental issues have raised the consumer's concern toward the use of more sustainable materials, including hydrogels. However, are greener materials compatible with high functionality? In a safe-by-design approach, this work demonstrates that functional hydrogels with in situ responsivity of their elastic properties by external stimuli can be developed from entirely "sustainable" components, a biobased amphiphile and biopolymers (gelatin, chitosan, and alginate). The bioamphiphile is a stimuli-responsive glycolipid obtained by microbial fermentation, which can self-assemble into fibers, but also micelles or vesicles, in water under high dilution and by a rapid variation of the stimuli. The elastic properties of the bioamphiphile-/biopolymer-interpenetrated hydrogels can be modulated by selectively triggering the phase transition of the glycolipid and/or the biopolymer inside the gel by mean of temperature or pH.

Interpenetrated Biosurfactant-Biopolymer Orthogonal Hydrogels: The Biosurfactant's Phase Controls the Hydrogel's Mechanics

Controlling the viscoelastic properties of hydrogels is a challenge for many applications. Low molecular weight gelators (LMWGs) like bile salts and glycolipids and biopolymers like chitosan and alginate are good candidates for developing fully biobased hybrid hydrogels that combine the advantages of both components. Biopolymers lead to enhanced mechanics, while LMWGs add functionality. In this work, hybrid hydrogels are composed of biopolymers (gelatin, chitosan, and alginate) and microbial glycolipid bioamphiphiles, known as biosurfactants. Besides their biocompatibility and natural origin, bioamphiphiles can present chameleonic behavior, as pH and ions control their phase diagram in water around neutrality under strongly diluted conditions (<5 wt%). The glycolipid used in this work behaves like a surfactant (micellar phase) at high pH or like a phospholipid (vesicle phase) at low pH. Moreover, at neutral-to-alkaline pH in the presence of calcium, it behaves like a gelator (fiber phase). The impact of each of these phases on the elastic properties of biopolymers is explored by means of oscillatory rheology, while the hybrid structure is studied by small angle X-ray scattering. The micellar and vesicular phases reduce the elastic properties of the hydrogels, while the fiber phase has the opposite effect; it enhances the hydrogel's strength by forming an interpenetrated biopolymer-LMWG network.

A Novel Approach, Based on the Combined Action of Chitosan Hydrogel and Laccases, for the Removal of Dyes from Textile Industry Wastewaters

Dyes are considered as one the most important classes of contaminants that threaten the environment and human life. The synergy between the adsorption capacity of chitosan hydrogels and the catalytic properties of the enzyme laccase was exploited to improve the removal of contaminants from a liquid stream. The adsorption capacity of a chitosan hydrogel was tested on three different textile dyes. The effect of pH on the adsorption efficiency was dependent on the dye tested: the removal of methylene blue (MB), a cationic dye, was more effective at alkaline values of pH, whereas bromophenol blue (BPB) and Coomassie brilliant blue (BB), both anionic dyes, were more effectively removed under acid environments. The use of laccase immobilized onto chitosan has significantly improved the efficiency of dye removal, exploiting the synergy between the adsorption capacity of chitosan and the catalytic properties of the enzyme. The simultaneous processes of adsorption and enzymatic degradation improved the dye removal whatever the pH value adopted, making the removal efficiency less dependent from the pH changes. The chitosan used as a support for the immobilization of laccases showed good stability under repeated cycles, demonstrating the feasibility of the method developed for the application in wastewater remediation.

Development of Quaternized Chitosan Integrated with Nanofibrous Polyacrylonitrile Mat as an Anion-Exchange Membrane

A two-phase anion-exchange membrane was prepared from quaternized chitosan (QCS) integrated with an electrospun polyacrylonitrile (PAN) scaffold by spin coating. To synthesize QCS, glycidyltrimethylammonium chloride in various amounts was introduced into the structure of CS. The characterization of the cast cross-linked QCS (CQCS) membranes by impedance spectroscopy revealed the ionic conductivity (IC) in the range of 2.8 × 10^-4 to 8.2 × 10^-4 S cm^-1 and the degree of quaternization (DQ) of 26.4-51.0%, where the CQCS film with the DQ of 51.0% showed excellent performance. When CQCS was reinforced with a PAN fiber mat, the newly developed composite membrane demonstrated the highest IC of 34 × 10^-4 S cm^-1 at 80 °C, low swelling, and an almost eightfold increase in tensile strength at a fully hydrated state compared to pristine materials. Moreover, the CQCS/PAN membrane was chemically stable and revealed increasing hydroxide transport during 1 month immersion in alkaline media.