Microfibrillated cellulose enhancement to mechanical and conductive properties of biocompatible hydrogels

Sodium carboxymethyl cellulose and MXene reinforced multifunctional conductive hydrogels for multimodal sensors and flexible supercapacitors

With the growing demand for eco-friendly materials in wearable smart electronic devices, renewable, biocompatible, and low-cost hydrogels based on natural polymers have attracted much attention. Cellulose, as one of the renewable and degradable natural polymers, shows great potential in wearable smart electronic devices. Multifunctional conductive cellulose-based hydrogels are designed for flexible electronic devices by adding sodium carboxymethyl cellulose and MXene into polyacrylic acid networks. The multifunctional hydrogels possess excellent mechanical property (stress: 310 kPa; strain: 1127 %), toughness (206.67 KJ m-3), conductivity (1.09 ± 0.12 S m-1) and adhesion (82.19 ± 3.65 kPa). The multifunctional conductive hydrogels serve as strain sensors (Gauge Factor (GF) = 5.79, 0-700 % strain; GF = 14.0, 700-900 % strain; GF = 40.36, 900-1000 % strain; response time: 300 ms; recovery time: 200 ms) and temperature sensors (Temperature coefficient of resistance (TCR) = 2.5755 °C-1 at 35 °C- 60 °C). The sensor detects human activities with clear and steady signals. A distributed array of flexible sensors is created to measure the magnitude and distribution of pressure and a hydrogel-based flexible touch keyboard is also fabricated to recognize writing trajectories, pressures and speeds. Furthermore, a flexible hydrogel-based supercapacitor powers the LED and exhibits good cyclic stability over 15,000 charge-discharge cycles.

Application of Conductive Hydrogels on Spinal Cord Injury Repair: A Review

Spinal cord injury (SCI) causes severe motor or sensory damage that leads to long-term disabilities due to disruption of electrical conduction in neuronal pathways. Despite current clinical therapies being used to limit the propagation of cell or tissue damage, the need for neuroregenerative therapies remains. Conductive hydrogels have been considered a promising neuroregenerative therapy due to their ability to provide a pro-regenerative microenvironment and flexible structure, which conforms to a complex SCI lesion. Furthermore, their conductivity can be utilized for noninvasive electrical signaling in dictating neuronal cell behavior. However, the ability of hydrogels to guide directional axon growth to reach the distal end for complete nerve reconnection remains a critical challenge. In this Review, we highlight recent advances in conductive hydrogels, including the incorporation of conductive materials, fabrication techniques, and cross-linking interactions. We also discuss important characteristics for designing conductive hydrogels for directional growth and regenerative therapy. We propose insights into electrical conductivity properties in a hydrogel that could be implemented as guidance for directional cell growth for SCI applications. Specifically, we highlight the practical implications of recent findings in the field, including the potential for conductive hydrogels to be used in clinical applications. We conclude that conductive hydrogels are a promising neuroregenerative therapy for SCI and that further research is needed to optimize their design and application.

Exploring the TEMPO-Oxidized Nanofibrillar Cellulose and Short Ionic-Complementary Peptide Composite Hydrogel as Biofunctional Cellular Scaffolds

Multicomponent self-assembly is an emerging approach in peptide nanotechnology to develop nanomaterials with superior physical and biological properties. Inspired by the multicomponent nature of the native extracellular matrix (ECM) and the well-established advantages of co-assembly in the field of nanotechnology, we have attempted to explore the noncovalent interactions among the sugar and peptide-based biomolecular building blocks as an approach to design and develop advanced tissue scaffolds. We utilized TEMPO-oxidized nanofibrillar cellulose (TO-NFC) and a short ionic complementary peptide, Nap-FEFK, to fabricate highly tunable supramolecular hydrogels. The differential doping of the peptide into the TO-NFC hydrogel was observed to tune the surface hydrophobicity, microporosity, and mechanical stiffness of the scaffold. Interestingly, a differential cellular response was observed toward composite scaffolds with a variable ratio of TO-NFC versus Nap-FEFK. Composite scaffolds having a 10:1 (w/w) ratio of TO-NFC and the Nap-FEFK peptide showed enhanced cellular survival and proliferation under two-dimensional cell culture conditions. More interestingly, the cellular proliferation on the 10:1 matrix was found to be similar to that of Matrigel in three-dimensional culture conditions, which clearly indicated the potential of these hydrogels in advanced tissue engineering applications. Additionally, these composite hydrogels did not elicit any significant inflammatory response in Raw cells and supported their survival and proliferation, which further emphasized their ability to form versatile scaffolds for tissue regeneration. This multicomponent assembly approach to construct biomolecular composite hydrogels to access superior physical and biological properties within the scaffold is expected to improve the scope for designing novel ECM-mimicking biomaterials for regenerative medicine.

Nanocellulose-mediated transparent high strength conductive hydrogel based on in-situ formed polypyrrole nanofibrils as a multimodal sensor

A simple method was provided to prepare a transparent, highly conductive, mechanically reinforced, stretchable, and compressible hydrogel. In this system, pyrrole (Py) monomers were gently polymerized and uniformly deposited on the surface of cellulose nanofiber (CNF) via the improved in-situ polymerization. In the opaque PPy@CNF suspension, acrylamide monomers (AM) were dissolved and radical-polymerized to construct the PPy@CNF-PAM hydrogel with the in-situ formation of PPy nanofibrils in the presence of excess ammonium persulfate (APS). The in-situ formed PPy nanofibrils were well intertwined with the CNF and PAM chains, and a highly conductive path was established and permitted visible light to pass through. The amphipathic CNF took along and dispersed PPy aggregates well, and reinforced the hydrogel after formation of PPy nanofibrils. In view of the improved mechanical compressive, stretchable properties and excellent electrical conductivity (4.5 S/m), the resulting hydrogels could serve as a potential electrical device in a range of applications.

Polypyrrole-doped conductive self-healing multifunctional composite hydrogels with a dual crosslinked network

Soft hydrogel materials can be applied for use in biosensors, wearable electronics, artificial skin, soft robots, and so on. Practical applications require the materials to have various properties such as high conductivity, toughness, self-healing, stretchability, and so on. However, achieving all these features in a single material remains challenging at present. Herein, the fabrication of novel composite carboxymethylcellulose/poly(acrylic acid)/polypyrrole/Al(III) (CMC/PAA/PPy/Al(III)) multifunctional hydrogels using a simple method is described. The mechanical and electrical self-healing properties are attained by multiple dynamic coordinations between Al³⁺ ions and carboxyl groups from CMC and PAA together with the hydrogen bonding between PPy and the -OH of CMC and/or the -COOH of PAA. The electrical conductivity is achieved by the conductive polymer PPy, free ions, and the synergistic effect between the PPy particles and the free ions. Moreover, desirable mechanical properties, such as stretchability (1344%), toughness, and mouldability are realized by establishing a balance between the chemical and physical crosslinking networks, and the nanostructure of PPy. Thus, the resultant hydrogels have potential applications in electronic skin, biomedical implants, and wearable electronic devices in the future.

Polypyrrole-Doped Conductive Self-Healing Composite Hydrogels with High Toughness and Stretchability

In recent years, hydrogels with self-healing capability and conductivity have become ideal materials for the design of electrodes, soft robotics, electronic skin, and flexible wearable devices. However, it is still a critical challenge to achieve the synergistic characteristics of high conductivity, excellent self-healing efficiency without any stimulations, and decent mechanical properties. Herein, we developed a ferric-ion (Fe³⁺) crosslinked acrylic acid and chitosan polymer hydrogel using embedded polypyrrole particles with features of high conductivity (2.61S·m^-1) and good mechanical performances (a tensile strength of 628%, a stress of 0.33 MPa, an elastic modulus of 0.146 MPa, and a toughness of 1.14 MJ·m^-3). In addition, the self-healing efficiency achieved 93% in tensile strength after healing in the air for 9 h without any external stimuli. Therefore, with these outstanding mechanical, self-healing, and conductive abilities all in one, it is possible to fabricate a new kind of soft material with wide applications.

Characterization of Bio-Inspired Electro-Conductive Soy Protein Films

Protein-based conductive materials are gaining attention as alternative components of electronic devices for value-added applications. In this regard, soy protein isolate (SPI) was processed by extrusion in order to obtain SPI pellets, subsequently molded into SPI films by hot pressing, resulting in homogeneous and transparent films, as shown by scanning electron microscopy and UV-vis spectroscopy analyses, respectively. During processing, SPI denatured and refolded through intermolecular interactions with glycerol, causing a major exposition of tryptophan residues and fluorescence emission, affecting charge distribution and electron transport properties. Regarding electrical conductivity, the value found (9.889 × 10⁻⁴ S/m) is characteristic of electrical semiconductors, such as silicon, and higher than that found for other natural polymers. Additionally, the behavior of the films in contact with water was analyzed, indicating a controlled swelling and a hydrolytic surface, which is of great relevance for cell adhesion and spreading. In fact, cytotoxicity studies showed that the developed SPI films were biocompatible, according to the guidelines for the biological evaluation of medical devices. Therefore, these SPI films are uniquely suited as bioelectronics because they conduct both ionic and electronic currents, which is not accessible for the traditional metallic conductors.

Extrusion-Based Bioprinting of Multilayered Nanocellulose Constructs for Cell Cultivation Using In Situ Freezing and Preprint CaCl2 Cross-Linking

Extrusion-based bioprinting with a preprint cross-linking agent and an in situ cooling stage provides a versatile method for the fabrication of 3D structures for cell culture. We added varying amounts of calcium chloride as a precross-linker into native nanofibrillated cellulose (NFC) hydrogel prior to 3D bioprinting to fabricate structurally stable multilayered constructs without the need for a separate cross-linking bath. To further enhance their stability, we bioprinted the multilayered structures onto an in situ temperature-controlled printing stage at 25, 0, and -10 °C. The extruded and subsequently freeze-dried volumetric constructs maintained their structures after being immersed into a cell culture medium. The ability to maintain the shape after immersion in cell media is an essential feature for the fabrication of stem cell-based artificial organs. We studied the viability and distribution of mouse embryonic fibroblast cells into the hydrogels using luminescence technique and confocal microscopy. Adding CaCl2 increased the stability of the multilayered nanocellulose structures, making them suitable for culturing cells inside the 3D hydrogel environment. Lower stage temperature considerably improved the structural stability of the 3D printed structures, however, had no effect on cell viability.

From waste of marine culture to natural patch in cardiac tissue engineering

Sea squirt, as a highly invasive species and main biofouling source in marine aquaculture, has seriously threatened the biodiversity and aquaculture economy. On the other hand, a conductive biomaterial with excellent biocompatibility, and appropriate mechanical property from renewable resources is urgently required for tissue engineering patches. To meet these targets, we presented a novel and robust strategy for sustainable development aiming at the marine pollution via recycling and upgrading the waste biomass-sea squirts and serving as a renewable resource for functional bio-scaffold patch in tissue engineering. We firstly demonstrated that the tunic cellulose derived natural self-conductive scaffolds successfully served as functional cardiac patches, which significantly promote the maturation and spontaneous contraction of cardiomyocytes both in vitro and enhance cardiac function of MI rats in vivo. We believe this novel, feasible and “Trash to Treasure” strategy to gain cardiac patches via recycling the waste biomass must be promising and beneficial for marine environmental bio-pollution issue and sustainable development considering the large-scale consumption potential for tissue engineering and other applications.

•

Fouling sea squirts used as scaffold materials can effectively solve the pollution problem of marine aquaculture.

•

The natural electrical conductivity of the sea squirts derived scaffold is similar to that of natural myocardial tissue.

•

Cellulose scaffold from sea squirts has a good orientation, and its structure is similar to natural myocardial tissue.

•

Sea squirts cellulose derived natural self-conductive scaffolds were successfully served as the functional cardiac patches.

Fabrication of nanochitosan incorporated polypyrrole/alginate conducting scaffold for neural tissue engineering

The utilization of conductive polymers for fabrication of neural scaffolds have attracted much interest because of providing a microenvironment which can imitate nerve tissues. In this study, polypyrrole (PPy)-alginate (Alg) composites were prepared using different percentages of alginate and pyrrole by oxidative polymerization method using FeCl3 as an oxidant and electrical conductivity of composites were measured by four probe method. In addition, chitosan-based nanoparticles were synthesized by ionic gelation method and after characterization merged into PPy-Alg composite in order to fabricate a conductive, hydrophilic, processable and stable scaffold. Physiochemical characterization of nanochitosan/PPy-Alg scaffold such as electrical conductivity, porosity, swelling and degradation was investigated. Moreover, cytotoxicity and proliferation were examined by culturing OLN-93 neural and human dermal fibroblasts cells on the Nanochitosan/PPy-Alg scaffold. Due to the high conductivity, the film with ratio 2:10 (PPy-Alg) was recognized more suitable for fabrication of the final scaffold. Results from FT-IR and SEM, evaluation of porosity, swelling and degradation, as well as viability and proliferation of OLN-93 neural and fibroblast cells confirmed cytocompatiblity of the Nanochitosan/PPy-Alg scaffold. Based on the features of the constructed scaffold, Nanochitosan/PPy-Alg scaffold can be a proper candidate for neural tissue engineering.

Preparations of Tough and Conductive PAMPS/PAA Double Network Hydrogels Containing Cellulose Nanofibers and Polypyrroles

To afford an intact double network (sample abbr.: DN) hydrogel, two-step crosslinking reactions of poly(2-acrylamido-2-methylpropanesulfonic acid) (i.e., PAMPS first network) and then poly(acrylic acid) (i.e., PAA second network) were conducted both in the presence of crosslinker (N,N'-methylenebisacrylamide (MBAA)). Similar to the two-step processes, different contents of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) oxidized cellulose nanofibers (TOCN: 1, 2, and 3 wt.%) were initially dispersed in the first network solutions and then crosslinked. The TOCN-containing PAMPS first networks subsequently soaked in AA and crosslinker and conducted the second network crosslinking reactions (TOCN was then abbreviated as T for DN samples). As the third step, various (T-)DN hydrogels were then treated with different concentrations of FeCl3(aq) solutions (5, 50, 100, and 200 mM). Through incorporations of ferric ions into (T-)DN hydrogels, notably, three purposes are targeted: (i) strengthen the (T-)DN hydrogels through ionic bonding, (ii) significantly render ionic conductivity of hydrogels, and (iii) serve as a catalyst for the forth step to proceed with in situ chemical oxidative polymerizations of pyrroles to afford polypyrrole-containing (sample abbr.: Py) hydrogels [i.e., (T-)Py-DN samples]. The characteristic functional groups of PAMPS, PAA, and Py were confirmed by FT-IR. Uniform microstructures were observed by cryo scanning electron microscopy (cryo-SEM). These results indicated that homogeneous composites of T-Py-DN hydrogels were obtained through the four-step process. All dry samples showed similar thermal degradation behaviors from the thermogravimetric analysis (TGA). The T2-Py5-DN sample (i.e., containing 2 wt.% TOCN with 5 mM FeCl3(aq) treatment) showed the best tensile strength and strain at breaking properties (i.e., σTb = 450 kPa and εTb = 106%). With the same compositions, a high conductivity of 3.34 × 10-3 S/cm was acquired. The tough T2-Py5-DN hydrogel displayed good conductive reversibility during several "stretching-and-releasing" cycles of 50-100-0%, demonstrating a promising candidate for bioelectronic or biomaterial applications.

Effect of cellulose size-concentration on the structure of polyvinyl alcohol hydrogels

Microfibrillated cellulose as a reinforcement agent has been investigated extensively due to their unique characteristics, which can reorder the structure of polymers and hydrogels leading to improved mechanical properties with minimal disadvantages in terms of the targeted original applications. However, effect of using a macro- to a micro-fibrillated cellulose onto polyvinyl alcohol hydrogels is still unknown, because of the unique ability for both to be produced as hydrogels from freeze-thawing mechanisms - hydrogen bonding - there is a potential synergism. Therefore, macro and microfibrillated kraft bleached paper was synthesised at various concentrations on polyvinyl alcohol hydrogels. The overall effect presented a strong interaction between both compounds but it was increased with macrofibrillated cellulose. Increase in crystallinity was also observed with a macro-sized fibre without variation on tensile elastic modulus but an overall improvement was perceived on thermal properties and a slower swelling rate with a microfibrillated cellulose.

Processing and modification of hydrogel and its application in emerging contaminant adsorption and in catalyst immobilization: a review

Due to the wonderful property of hydrogels, they can provide a platform for a wide range of applications. Recently, there is a growing research interest in the development of potential hydrogel adsorbents in wastewater treatment due to their adsorption ability toward aqueous pollutants. It is important to prepare such a hydrogel that possesses appropriate robustness, adsorption capacity, and adsorption efficiency to meet the need of water treatment. In order to improve the property of hydrogels, much effort has been made by researchers to modify hydrogels, among which incorporating inorganic components into the polymeric networks is the most common method, which can reduce the product cost and simplify the preparation procedure. Not only can hydrogel be applied as adsorbent, but it also can be used as matrix for catalyst immobilization. In this review, the key advancement on the preparation and modification of hydrogels is discussed, with special emphasis on the introduction of inorganic materials into polymeric networks and consequential changes in the properties of mechanical strength, swelling, and adsorption. Besides, hydrogels used as adsorbents for removal of dyes and inorganic pollutants have been widely explored, but their use for adsorbing emerging contaminants from aqueous solution has not received much attention. Thus, this review is mainly focused on hydrogels' application in removing emerging contaminants by adsorption. Furthermore, hydrogels can be also applied in immobilizing catalysts, such as enzyme and photocatalyst, to remove pollutants completely and avoid secondary pollution, so their progress as catalyst matrix is overviewed.

A bioinspired hydrogen bond crosslink strategy toward toughening ultrastrong and multifunctional nanocomposite hydrogels

A bioinspired hydrogen bond crosslink strategy enabled the physical hydrogels to possess exceptional mechanical properties, good self-recoverability, versatile adhesiveness, biocompatibility and antibacterial properties.

Calcium Phosphate Incorporated Bacterial Cellulose-Polyvinylpyrrolidone Based Hydrogel Scaffold: Structural Property and Cell Viability Study for Bone Regeneration Application

This work focuses on the analysis of structural and functional properties of calcium phosphate (CaP) incorporated bacterial cellulose (BC)-polyvinylpyrrolidone (PVP) based hydrogel scaffolds referred to as “CaP/BC-PVP”. CaP is incorporated in the scaffolds in the form of hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) in different concentrations (β-TCP: HA (w/w) = 20:80, 40:60, and 50:50). The scaffolds were characterized on the basis of porosity, thermal, biodegradation, mechanical, and cell viability/cytocompatibility properties. The structural properties of all the hydrogel scaffolds show significant porosity. The biodegradation of “CaP/BC-PVP” scaffold was evaluated following hydrolytic degradation. Weight loss profile, pH change, scanning electron microscopy (SEM), and Fourier Transform Infrared Spectroscopy (FTIR) study confirm the significant degradability of the scaffolds. It is observed that a 50:50_CaP/BC-PVP scaffold has the highest degree of degradation. On the other hand, the compressive strengths of CaP/BC-PVP hydrogel scaffolds are found between 0.21 to 0.31 MPa, which is comparable with the human trabecular bone. The cell viability study is performed with a human osteosarcoma Saos-2 cell line, where significant cell viability is observed in all the hydrogel scaffolds. This indicated their ability to facilitate cell growth and cell proliferation. Considering all these substantial properties, CaP/BC-PVP hydrogel scaffolds can be suggested for detailed investigation in the context of bone regeneration application.

P-Glycoprotein Antibody Decorated Porous Hydrogel Particles for Capture and Release of Drug-Resistant Tumor Cells

Multidrug resistance is one of the leading causes of chemotherapy failure in cancer patients. Early detection and capture of drug-resistant tumor cells can facilitate the monitoring of the therapy process and improve the prognosis of patients. In this study, novel P-glycoprotein (P-gp) antibody modified porous hydrogel particles are proposed for drug-resistant tumor cells capture. The hydrogel particles employ a highly biocompatible hydrogel, methacrylate gelatin (GelMA), as the carrier and replicate from the silica colloidal crystal beads. By the modification of P-gp antibody probes on their surfaces, the hydrogel particles are endowed with the ability to capture drug-resistant tumor cells, which overexpress specific components of P-gp on their membranes. Additionally, the acquired ordered porous nanostructure of the particles can provide not only more surface area for antibody immobilization but also a nanopatterned platform for highly efficient target cell capture. The above advantages make the porous hydrogel particles ideal for efficient capture and detection of the drug-resistant tumor cells, which can be expected to facilitate the point-of-care pharmacotherapy and promisingly improve the patient outcomes.