Polysaccharide-based adsorbents prepared in ionic liquid with high performance for removing Pb(II) from aqueous systems

Co-precipitation fabrication of cellulose/chitosan-aniline grafted composites for efficient removal of Pb2+ ions from aqueous solution

Heavy metal ions, are non-biodegradable, high toxic tendency, and have serious hazardous effects on the health of humans. Then, removing them from the environment using different techniques is necessary. Several routes are expensive, low-efficient, and require a long time to achieve adsorption equilibrium. In this paper, novel chitosan-based composites CS/CL@An-1 and CS/CL@An-2 were synthesized, characterized by FT-IR, DSC, XRD, and SEM, and applied as new adsorbents in batch experiments for the removal of Pb2+ ions from aqueous solution. The effect of important parameters such as initial pH solution (2-7), adsorbent dose (0.005, 0.01, and 0.02 g), adsorption contact time (0-240 min), initial Pb2+ metal ion (25-200 mg/L) and ionic strength on their adsorption behavior was investigated. The adsorption results at best conditions (pH solution = 6, adsorbent dose = 0.02 g, contact time = 180 min and initial ion concentration = 100 mg/L) predicted that the maximum removal percentage (adsorption capacity) of Pb2+ metal ion using CS/CL@An-1 and CS/CL@An-2 is 95.6 % (239 mg/g) and 98.8 % (247 mg/g), respectively, much higher than other chitosan-based adsorbents. The absorption kinetic results confirmed that the adsorption of Pb2+ showed the best fit with the pseudo-second-order (PSO) model as a chemisorption process. The absorption mechanism was regulated by the coordination and n-π attractions of Pb2+ ions with the active sites on the surface of adsorbents. The adsorption of Pb2+ was well-fitted by a homogeneous monolayer Langmuir isotherm model. Finally, the reusability of adsorbents was examined after five adsorption-desorption cycles, and the results show that the adsorption efficiency still reaches >90 %. Therefore, the compounds were potentially new adsorbents for removing Pb2+ ions from aqueous solution.

Specific nickel recovery using screen-printed carbon electrode electrografted with ionic liquid

This study presents an innovative electrochemical method for selectively extracting nickel ions from aquatic solutions, employing electrodes enhanced with electrografted ionic liquids. Specifically, a styrenyl-imidazolium ionic liquid (SI-IL) was synthesized, featuring a double bond for immobilization and an imidazole group targeting nickel ions. The electrografting process ensured uniform SI-IL distribution on the electrode's surface, as confirmed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). SI-IL-treated electrodes exhibited notable selectivity towards nickel ions, efficiently recovering them as nanoparticles while reducing the required reduction potential. In pH conditions similar to industrial wastewater, SI-IL modified electrodes demonstrated substantial enhancement in nickel recovery rates compared to unmodified electrodes.

NiFe2O4/g- C3N4 modified chitosan Schiff base composite for efficient removal of Cu(II) and Hg(II) ions from the aquatic environment and its antibacterial properties

Modification of chitosan has been achieved by the reaction of chitosan with 4- nitro-benzaldehyde via the sol-gel method, resulting in a Schiff base. A novel magnetic Graphitic Carbon Nitride/chitosan-Schiff base/NiFe2O3 (SBIV@NiFe/g-C3N4) adsorbent was synthesized by hydrothermal route for the adsorption of Cu(II) and Hg(II) ions from the aquatic environment. The synthesized SBIV@NiFe/g-C3N4 was characterized using infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), vibrating sample magnetometer (VSM), and Brunauer-Emmett-Teller (BET), with a surface area of approximately 13.657 m2/g. It was anticipated by the results that magnetic SBIV@NiFe/g-C3N4 would be effectively synthesized. On Cu(II) and Hg(II) adsorption, the impacts of significant variables, including pH solution, contact duration, metal ion concentration, adsorbent dosage, and co-existing ions, were examined. Under ideal circumstances, the optimum adsorption capacities of Cu(II) and Hg(II) ions were 889.76 mg/g and 703.21 mg/g, respectively. Furthermore, the SBIV@NiFe/g-C3N4 material exhibited the beneficial property of simple separation, permitting the continuation of high removal effectiveness for heavy metals like Cu (II) and Hg(II) despite experiencing many reuse cycles. In summary, there are a lot of opportunities for the effective elimination of Cu (II) and Hg (II) from different water sources shortly with the use of SBIV@NiFe/g-C3N4, a new adsorbent. The as-synthesized SBIV@NiFe/g-C3N4 displayed better antibacterial activity against highly lethal bacteria like S. aureus and P. vulgaris.

Synthesis and characterization of chitosan Schiff base grafted with formaldehyde and aminoethanol: As an effective adsorbent for removal of Pb(II), Hg(II), and Cu(II) ions from aqueous media

Grafted chitosan materials show the characteristics of high stability, easy separation and recovery, and good heavy metal adsorption capacity, and have received much attention in the adsorption process. Therefore, in this work, novel grafted chitosan-based adsorbent CS-EHBSB@F-AE was prepared by a one-pot reaction of chitosan (CS), 3-ethoxy-4-hydroxybenzaldehyde (EHB), formaldehyde (F) and aminoethanol (F). The microstructure and morphology of the as-prepared composite CS-EHBSB@F-AE were characterized by FT-IR, TGA, DSC, FE-SEM, and BET analyses. The adsorption performance of the as-prepared CS-EHBSB@F-AE composite on Pb(II), Hg(II), and Cu(II) ions from aqueous was investigated using batch experiment and the effects of the initial pH of the solution, contact time, and initial metal ions concentration and temperature on the adsorption efficiency were investigated and discussed. At the best conditions, CS-EHBSB@F-AE exhibited remarkable adsorption capacity of 246.7 mg/g, 203.9 mg/g, and 234.4 mg/g in absorbing Pb(II), Hg(II), and Cu(II), respectively. The adsorption equilibrium and the kinetic studies confirmed that the ions adsorption process fits well with the Langmuir isotherm and pseudo-second-order (PSO) models. Additionally, the adsorption efficiency of Pb(II), Hg(II), and Cu(II) metal ions by the composite CS-EHBSB@F-AE was reduced by increasing the temperature from 298 K to 318 K. In addition, after the sixth ads/des cycles, the as-prepared adsorbent still exhibited high removal efficiency with a decrease in adsorption efficiency of Pb(II) (5.53 %), Hg(II) (15.43 %) and Cu(II) (8.27 %). Finally, we proposed that the ions adsorption by CS-EHBSB@F-AE has happened using the coordination of active groups containing nitrogen and oxygen atoms on the surface of the adsorbent with the Pb(II), Hg(II), and Cu(II) metal ions.

Effects of different selenium biofortification methods on Pleurotus eryngii polysaccharides: Structural characteristics, antioxidant activity and binding capacity in vitro

The effects of selenium biofortification methods involving sodium selenite and selenium yeast on the structural characteristics, antioxidant activity and binding capacity of Pleurotus eryngii polysaccharides were investigated. Sodium selenite Se-enriched Pleurotus eryngii polysaccharides (Se-SPEP), selenium yeast Se-enriched Pleurotus eryngii polysaccharides (Se-YPEP), and Pleurotus eryngii polysaccharides (PEP) had Se contents of 20.548 ± 1.561, 19.822 ± 0.613, and 0.052 ± 0.016 μg/g, respectively. Compared with PEP, Se-SPEP and Se-YPEP had lower molecular weight and contained the same monosaccharides in varying molar ratios. The results of FT-IR, PS, ZP, and SEM indicated significant alterations in structural characteristics following selenium biofortification. Se-PEPs exhibited superior activity against ABTS, DPPH, and ·OH radicals, as well as the higher binding capacity for Cd2+ and Cu2+ compared to natural polysaccharides. The binding capacity of the polysaccharides for Cd2+ and Cu2+ was higher at pH 6.8 compared to pH 2.0, while the opposite was observed for Pb2+. Furthermore, Se-PEPs exhibited a significantly higher binding capacity for Cd2+ and Cu2+ at both pH levels compared to natural polysaccharides (P < 0.05). Se-YPEP displayed higher antioxidant activity than Se-SPEP, with their binding capacities reversed. These data indicated that selenium biofortification methods have different positive impacts on the structure and activity of polysaccharides compared to natural polysaccharides, making Se-PEPs promising dietary supplements for safeguarding the body against the risks posed by food-derived heavy metals.

Antimicrobial Composites Based on Methacrylic Acid-Methyl Methacrylate Electrospun Fibers Stabilized with Copper(II)

This study presents fibers based on methacrylic acid-methyl methacrylate (Eudragit L100) as Cu(II) adsorbents, resulting in antimicrobial complexes. Eudragit L100, an anionic copolymer synthesized by radical polymerization, was electrospun in dimethylformamide (DMF) and ethanol (EtOH). The electrospinning process was optimized through a 22-factorial design, with independent variables (copolymer concentration and EtOH/DMF volume ratio) and three repetitions at the central point. The smallest average fiber diameter (259 ± 53 nm) was obtained at 14% w/v Eudragit L100 and 80/20 EtOH/DMF volume ratio. The fibers were characterized using scanning electron microscopy (SEM), infrared spectroscopy in attenuated total reflectance mode (FTIR-ATR), and differential scanning calorimetry (DSC). The pseudo-second-order mechanism explained the kinetic adsorption toward Cu(II). The fibers exhibited a maximum adsorption capacity (qe) of 43.70 mg/g. The DSC analysis confirmed the Cu(II) absorption, indicating complexation between metallic ions and copolymer networks. The complexed fibers showed a lower degree of swelling than the non-complexed fibers. The complexed fibers exhibited bacteriostatic activity against Gram-negative (Pseudomonas aeruginosa) and Gram-positive (Staphylococcus aureus) bacteria. This study successfully optimized the electrospinning process to produce thin fibers based on Eudragit L100 for potential applications as adsorbents for Cu(II) ions in aqueous media and for controlling bacterial growth.

Fabrication of a novel polyvinylpyrrolidone/chitosan-Schiff base/Fe2O3 nanocomposite for efficient adsorption of Pb(II) and Hg(II) ions from aqueous solution

A novel magnetic polyvinylpyrrolidone/chitosan-Schiff base/Fe2O3 (PVP/CS-SB/Fe2O3) adsorbent was prepared by one-pot facile co-precipitation route for adsorption of Pb(II) and Hg(II) ions from aqueous solution. Fourier transform infrared-spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and Brunauer-Emmett-Teller (BET) were used to characterize the synthesized PVP/CS-SB/Fe2O3. The results predicted that the successfully synthesis of magnetic CSSB-PVP@Fe2O3. The effects of important factors such as pH solution, contact time, concentration of metal ions, adsorbent dose and co-existing ions on Pb(II) and Hg(II) adsorption were investigated. The maximum adsorption capacities of Pb(II) and Hg(II) ions at optimal conditions were 120 mg/g and 102.5 mg/g, respectively. The kinetic studies predicted that the adsorption followed the pseudo-second-order (PSO) model as chemisorption using the coordination of active sites of PVP/CS-SB/Fe2O3 with the metal ions and also n-π interactions. Reproducibility results predicted that the excellent regeneration ability after 6 adsorption cycles. According to the results of this work, the PVP/CS-SB/Fe2O3 nanocomposite is promising for Pb(II) and Hg(II) ions adsorption and can be potential as a simple, low-cost, high-efficient adsorbent for decontamination of other heavy metal ions from aqueous solution.

Synthesis and characterization of pendant N,N-dimethylaminobenzaldehyde-functionalized chitosan Schiff base composite (CS@MABA) as a new sorbent for removal of Pb(II) ions from aqueous media

In this work, new pendant N,N-dimethylaminobenzaldehyde-functionalized chitosan Schiff base composite (CS@MABA) was prepared from the simple and convenient condensation reaction between chitosan (CS) and N,N-dimethylaminobenzaldehyde (MABA) in ethanol-glacial acetic acid (1:1 v/v) and characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), differential scanning calorimetry (DSC) and scanning electron microscope (SEM). The as-prepared composite CS@MABA was applied for the removal of Pb(II) ions, due to the presence of imine, hydroxyl and phenyl groups, and the effects of important parameters such as solution pH, contact time and sorbent dosage on the removal percentage and adsorption capacity were investigated and discussed. The optimum conditions were found to be at pH 5, adsorbent dosage of 0.1 g, Pb(II) concentration of 50 mg/L and contact time of 60 min. The maximum Pb(II) removal percentage was found to be 94.28 % with the high adsorption capacity of 165 mg/g. The adsorption capacity of CS@MABA is remain 87 % after 5 adsorption-desorption cycles. The adsorption kinetic and isotherm studies indicated that the Pb(II) removal by CS@MABA follows a pseudo-first order and Langmuir models, respectively. Compared to similar compounds, the synthesized CS@MABA composite has shown a relatively high yield for removing Pb(II) ions. According to these results, the CS@MABA suggested for the sorption of other heavy metals.

Application of new chitosan 2,4-dihydroxyacetophenone Schiff base @SrFe12O19 nanocomposite for remove of Pb(II) ion from aqueous solution

A new chitosan 2,4-dihydroxyacetophenone Schiff base @SrFe₁₂O₁₉ (Cs-SB@SrFe₁₂O₁₉) nanocomposite was successfully prepared by one-pot reaction and fully characterized for its functional groups, morphology, elemental analysis and thermal behavior by FT-IR, XRD, VSM, DSC, TGA, zeta potential, FE-SEM and EDS techniques. The VSM result showed that Cs-SB@SrFe₁₂O₁₉ has M_s of 11.81 emu/g and H_c of 5488 Oe, known as hard magnetic material. Finally, the as-prepared sample utilized as a new sorbent for the removal of Pb(II) ions from aqueous solution by using batch adsorption experiments. The adsorption of Pb(II) was carried out at different pH, contact time and initial dose of Cs-SB@SrFe₁₂O₁₉. The maximum adsorption capacity was found to be 132 mg/g (99 %) at pH 5 and the contact time of 120 min. Finally, the kinetic studies reveals that the adsorption process of Cs-SB@SrFe₁₂O₁₉ followed by the pseudo second order kinetics model. Also, the sample showed excellent recyclable efficiency up to 5 cycles.

Efficient removal of Pb(II) using modified chitosan Schiff base@Fe/NiFe

A novel modified chitosan Schiff base@Fe₂O₃-NiFe₂O₄ (CsSB@Fe/NiFe) was prepared and characterized using FT-IR, XRD, SEM, EDX, TGA, DSC and VSM. FT-IR and XRD results confirm that the nanoparticles of Fe/NiFe distributed throughout the surface of CS-OH and successfully prepared CsSB@Fe/NiFe. SEM image shows that the Fe/NiFe nanoparticles were assembled in the surface and inside of CS-OH. Coercivity (H_c) of CsSB@Fe/NiFe is ≈ 110 Oe, indicated that it was kind of soft-magnetic materials with saturation magnetization (M_s) of 6.45 emu/g. In addition, CsSB@Fe/NiFe was further explored as an new sorbent for the removal of Pb(II) ion from aqueous solution and the influence of various important parameters such as solution pH, contact time, dosage of adsorbent and initial Pb(II) concentration were studied and optimized. Optimum conditions for Pb(II) removal were found to be pH 5, adsorbent dosage 0.05 g, initial Pb(II) concentration of 75 ppm and contact time of 120 min. The maximum Pb(II) removal percentage was found to be 97%. Also, CsSB@Fe/NiFe shows about 88% Pb(II) removal after five adsorption-desorption cycles. The results suggested that the sorption of Pb(II) onto CsSB@Fe/NiFe was feasible and spontaneous.

Natural carbohydrate-based thermosensitive chitosan/pectin adsorbent for removal of Pb(II) from aqueous solutions

Biodegradable and eco-friendly adsorbents composed of natural carbohydrates have been used to replace carbon-based materials. This study presents a natural carbohydrate-based chitosan/pectin (CS/Pec) hydrogel adsorbent to remove Pb(II) from aqueous solutions. The physical CS/Pec hydrogel was prepared by blending aqueous CS and Pec solutions at 65 °C, preventing the use of toxic chemistries (crosslinking agents). The thermosensitive CS/Pec hydrogel was quickly created by cooling CS/Pec blend at room temperature. The used strategy created stable CS/Pec hydrogel against disintegration and water dissolution. The as-prepared hydrogel was characterized by infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The adsorbent had 1.688 mmol -COO^- for each gram. These ionized sites bind Pb(II) ions, promoting their adsorption. The adsorption kinetic and equilibrium studies indicated that the Elovich and pseudo-second-order models adjusted well to the experimental data, respectively. The maximum removal capacities (q_m) predicted by the Langmuir and Sips isotherms achieved 108.2 and 97.55 mg/g at 0.83 g/L adsorbent dosage (pH 4.0). The hydrogel/Pb(II) pair was characterized by scanning electron microscopy (SEM), X-ray dispersive energy (EDS), and differential scanning calorimetry (DSC). The chemisorption seems to play an essential role in the Pb(II) adsorption. Therefore, the adsorbent was not recovered, showing low potential for reusability.

Effective removal of levofloxacin drug and Cr(VI) from water by a composed nanobiosorbent of vanadium pentoxide@chitosan@MOFs

Wastewaters is generally polluted with various inorganic and organic contaminants which require effective multipurpose purification technology. In this respect, a novel V₂O₅@Ch/Cu-TMA nanobiosorbent was constructed via encapsulation of nanoscale metal organic frameworks (Cu-TMA) into vanadium pentoxide-imbedded-chitosan matrix to comprehensively investigate its efficiency in removal of levofloxacin drug (LEVO) (e.g., organic pollutant) and chromium (VI) (e.g., inorganic pollutant) from water. Both LEVO drug and Cr(VI) adsorptions were correlated to pseudo-second order (R² = 1) and Langmuir isotherm (R² = 0.9924 for LEVO and R² = 0.9815 for Cr(VI)). Adsorption of Cr(VI) was confirmed to be spontaneous and endothermic reactions, while LEVO was found to proceed via spontaneous and exothermic reactions based on the thermodynamic parameters. The emerged V₂O₅@Ch/Cu-TMA is regarded as an excellent nanobiosorbent for removal of inorganic contaminant as Cr(VI) from all natural water samples (tap, sea and wastewater) with percentages range 92.43%-96.95% and organic contaminant as LEVO drug from tap and wastewater (91.99%-97.20%).

Adsorption of benzene and toluene from aqueous solution using a composite hydrogel of alginate-grafted with mesoporous silica

Hydrogels are often claimed as optimal adsorbents for water treatment; however, their efficiency towards the removal of hydrophobic pollutants is still limited. As an alternative, hydrogels prepared from polymers functionalized with siliceous materials can overcome this issue. Here, a composite hydrogel (denoted as GEL-SBA15) was prepared using alginate grafted with mesoporous silica (SBA15) and poly(vinyl alcohol) for benzene and toluene adsorption from aqueous solutions. Adsorption studies demonstrated that a low dosage of GEL-SBA15 (10 mg) has a high adsorption capacity for benzene (1482.8 mg/g) and toluene (596.6 mg/g) under mild experimental conditions (pH 7.0, at 25 °C). Besides, the adsorption capacities of GEL-SBA15 for both pollutants were enhanced compared to the conventional hydrogel. Kinetic analysis showed that the adsorption of benzene and toluene follows a pseudo-second order model, while the experimental adsorption data were well-fitted by the Freundlich isotherm. According to this isotherm, the adsorption occurs via a collaborative process, and weak physical forces (π-π interactions, van der Waals and hydrophobic) are involved. Hence, the post-utilized GEL-SBA15 can be recycled and reused up to 6 times without losing adsorption performance. Although hydrogels are not common adsorbents for aromatic hydrocarbons, the results reported here rank GEL-SBA15 as a promising adsorbent for the removal of these pollutants from water.

Application of a polyelectrolyte complex based on biocompatible polysaccharides for colorectal cancer inhibition

Strategies for incorporating water-insoluble photosensitisers (PS) in drug delivery systems have been extensively studied. In this work, we evaluate the formation, characterisation, drug sorption studies, and cytotoxicity of chitosan (CHT)/chondroitin sulphate (CS) polyelectrolyte complexes (PECs) coated with polystyrene-block-poly(acrylic acid) (PS-b-PAA) nanoparticles (NPs) loaded with chloroaluminum phthalocyanine (AlClPc). The PECs were characterised by infrared spectroscopy (FTIR), differential scanning calorimetric (DSC), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The PS-b-PAA NPs on the PEC surface was confirmed by scanning electron microscopy (SEM). Additionally, optical images distinguished the PEC structures containing PS-b-PAA or PS-b-PAA/AlClPc from the unloaded PEC. Kinetic and equilibrium studies investigate the sorption capacity of the PEC/PS-b-PAA toward AlClPc. The encapsulation efficiency reached 95% at 190 μg mL^-1 AlClPc after only 15 min. The Brunauer-Emmett-Teller (BET) isotherm and pseudo-second-order kinetic fitted well to the experimental data. The PS-b-PAA NPs on the PEC surfaces increase the AlClPc bioavailability and the PEC structure stabilizes the PS-b-PAA/AlClPc nanostructures. The materials were cytocompatible upon healthy VERO (kidney epithelial cells), and cytotoxic against colorectal cancerous cells (HT-29 cells). For the first time, we associate PS-b-PAA/AlClPc with a hydrophilic and cytocompatible polysaccharide matrix. We suggest the use of these materials in strategies to treat cancer by using photodynamic therapy.

Protein and Polysaccharide-Based Fiber Materials Generated from Ionic Liquids: A Review

Natural biomacromolecules such as structural proteins and polysaccharides are composed of the basic building blocks of life: amino acids and carbohydrates. Understanding their molecular structure, self-assembly and interaction in solvents such as ionic liquids (ILs) is critical for unleashing a flora of new materials, revolutionizing the way we fabricate multi-structural and multi-functional systems with tunable physicochemical properties. Ionic liquids are superior to organic solvents because they do not produce unwanted by-products and are considered green substitutes because of their reusability. In addition, they will significantly improve the miscibility of biopolymers with other materials while maintaining the mechanical properties of the biopolymer in the final product. Understanding and controlling the physicochemical properties of biopolymers in ionic liquids matrices will be crucial for progress leading to the ability to fabricate robust multi-level structural 1D fiber materials. It will also help to predict the relationship between fiber conformation and protein secondary structures or carbohydrate crystallinity, thus creating potential applications for cell growth signaling, ionic conductivity, liquid diffusion and thermal conductivity, and several applications in biomedicine and environmental science. This will also enable the regeneration of biopolymer composite fiber materials with useful functionalities and customizable options critical for additive manufacturing. The specific capabilities of these fiber materials have been shown to vary based on their fabrication methods including electrospinning and post-treatments. This review serves to provide basic knowledge of these commonly utilized protein and polysaccharide biopolymers and their fiber fabrication methods from various ionic liquids, as well as the effect of post-treatments on these fiber materials and their applications in biomedical and pharmaceutical research, wound healing, environmental filters and sustainable and green chemistry research.

Removal of Cu(II) from aqueous solutions imparted by a pectin-based film: Cytocompatibility, antimicrobial, kinetic, and equilibrium studies

To obtain pectin-based films is challenging due to the aqueous instability of polyelectrolyte mixtures. We overcome this issue by blending chitosan to pectin of high O-methoxylation degree (56%), followed by solvent evaporation. A durable film containing 74 wt% pectin content was produced and used as an adsorbent material toward Cu(II) ions. Kinetic and adsorption equilibrium studies showed that the pseudo-second-order and Sips isotherm models adjusted well to the experimental data, respectively. Langmuir isotherm indicated a maximum adsorption capacity (q_m) for Cu(II) removal of 29.20 mg g^-1. Differential scanning calorimetry, contact angle measurements, and X-ray photoelectron spectroscopy confirm the adsorption. The chemisorption plays an essential role in the process; thereby, the film reusability is low. After adsorption, the cytocompatible film/Cu(II) pair prevents the proliferation of Escherichia coli.