All cellulose composites prepared by hydroxyethyl cellulose and cellulose nanocrystals through the crosslink of polyisocyanate

Construction of greenly biodegradable bacterial cellulose/UiO-66-NH2 composite separators for efficient enhancing performance of lithium-ion battery

The disposal of waste lithium batteries, especially waste separators, has always been a problem, incineration and burial will cause environmental pollution, therefore, the development of degradable and high-performance separators has become an important challenge. Herein, UiO-66-NH2 particles were successfully anchored onto bacterial cellulose (BC) separators by epichlorohydrin (ECH) as a crosslinker, then a BC/UiO-66-NH2 composite separator was prepared by vacuum filtration. The ammonia groups (-NH2) from UiO-66-NH2 can form hydrogen bonds with PF6- in the electrolyte, promoting lithium-ion transference. Additionally, UiO-66-NH2 can store the electrolyte and tune the porosity of the separator. The lithium ion migration number (0.62) of the battery assembled with BC/UiO-66-NH2 composite separator increased by 50 % compared to the battery assembled with commercial PP separator (0.45). The discharge specific capacity of the battery assembled with BC/UIO-66-NH2 composite separator after 50 charge and discharge cycles is 145.4 mAh/g, which is higher than the average discharge specific capacity of 114.3 mAh/g of the battery assembled with PP separator. When the current density is 2C, the minimum discharge capacity of the battery assembled with BC/UiO-66-NH2 composite separator is 85.3 mAh/g. The electrochemical performance of the BC/UiO-66-NH2 composite separator is significantly better than that of the commercial PP separator. In addition, -NH2 can offer a nitrogen source to facilitate degradation of the BC separators, whereby the BC/UiO-66-NH2 composite separator could be completely degraded in 15 days.

Self-healing, environmentally stable and adhesive hydrogel sensor with conductive cellulose nanocrystals for motion monitoring and character recognition

Conductive hydrogel-based sensors offer diverse applications in artificial intelligence, wearable electronic devices and character recognition management. However, it remains a significant challenge to maintain their satisfactory performances under extreme climatic conditions. Herein, a stretchable, self-adhesive, self-healing and environmentally stable conductive hydrogel was developed through free radical polymerization of hydroxyethyl acrylate (HEA) and poly(ethylene glycol) methacrylate (PEG) as the skeleton, followed by the incorporation of polyaniline-coated cellulose nanocrystal (CNC@PANI) as the conductive and reinforced nanofiller. Encouragingly, the as-prepared hydrogel (CHP) exhibited decent mechanical strength, satisfactory self-adhesion, prominent self-healing property (95.04 % after 60 s), excellent anti-freezing performance (below -60 °C) and outstanding moisture retention. The assembled sensor derived from CHP hydrogel possessed a low detection limit (0.5 % strain), high strain sensitivity (GF = 1.68) and fast response time (96 ms). Remarkably, even in harsh environmental temperatures from -60 °C to 80 °C, it reliably detected subtle and large-scale human motion for a long-term process (>10,000 cycles), manifesting its exceptional environmental tolerance. More interestingly, this hydrogel-based sensor could be assembled into a "writing board" for accurate handwritten numeral recognition. Therefore, the as-obtained multifunctional hydrogel could be a promising material applied in human motion detection and character recognition platforms even in harsh surroundings.

Valorization of edible films based on chitosan/hydroxyethyl cellulose/olive leaf extract and TiO2-NPs for preserving sour cream

Biodegradable edible films for sour cream packaging were developed based on chitosan (CS), hydroxyethyl cellulose (HEC), Olive leaf extract (OE), and titanium dioxide nanoparticles (TiO2-NPs). The prepared CS/HEC/TiO2-OE bionanocomposite films were evaluated for their antimicrobial and antioxidant activities as well as using FT-IR, mechanical, permeability, and contact angle. The effect of developed films on the lipid oxidation, microbiological load, and chemical properties of sour cream was investigated. The fabricated films had an antimicrobial impact against all tested strains. The film containing 8 % OE showed effective protection against fat oxidation, with a peroxide value of 3.21 meq O2/kg, a para-anisidine value 5.40, and free fatty acids of 0.82 mg KOH/kg. The films with OE 4 % and 8 % have a good effect on the microbiological load of sour cream for 90 days. These films did not influence the chemical composition of sour cream and therefore can be used in this sort of dairy product.

Balancing mechanical property and swelling behavior of bacterial cellulose film by in-situ adding chitosan oligosaccharide and covalent crosslinking with γ-PGA

Bacterial cellulose (BC) is an ideal candidate material for drug delivery, but the disbalance between the swelling behavior and mechanical properties limits its application. In this work, covalent crosslinking of γ-polyglutamic acid (γ-PGA) with the chitosan oligosaccharide (COS) embedded in BC was designed to remove the limitation. As a result, the dosage, time, and batch of COS addition significantly affected the mechanical properties and the yield of bacterial cellulose complex film (BCCF). The addition of 2.25 % COS at the incubation time of 0.5, 1.5, and 2 d increased the Young's modulus and the yield by 5.65 and 1.42 times, respectively, but decreased the swelling behavior to 1774 %, 46 % of that of native BC. Covalent γ-PGA transformed the dendritic structure of BCCF into a spider network, decreasing the porosity and increasing the swelling behavior by 3.46 times. The strategy balanced the swelling behavior and mechanical properties through tunning hydrogen bond, electrostatic interaction, and amido bond. The modified BCCF exhibited a desired behavior of benzalkonium chlorides transport, competent for drug delivery. Thereby, the strategy will be a competent candidate to modify BC for such potential applications as wound dressing, artificial skin, scar-inhibiting patch, and so on.

Adjustable strength and toughness of dual cross-linked nanocellulose films via spherical cellulose as soft-phase

Nanocellulose films possess numerous merits ascribing to their inherent biocompatibility, non-toxic and biodegradability properties. The potential for practical applications would be improved if their mechanical strength and toughness requirements could be met simultaneously. Herein, dual cross-linked nanocellulose (DC) film was fabricated by the treatments of chemical and physical cross-linking, which was mechanically superior to pure nanocellulose (CNF) films. To further increase the toughness of DC films, spherical cellulose (Sph) was incorporated into DC film (DC-Sph film), and analyzed under different humidity conditions (RH) (from 10 % to 90 %). The changes of functional groups of CNF, DC and DC-Sph films were detected by FTIR and XPS spectrum. The epichlorohydrin and Sph content were optimized, followed by the investigation of RH on the toughness of films. The highest tensile strength (146.6 ± 4.6 MPa) was obtained in DC film at 50 % RH, while the DC-Sph film showed the largest toughness (40.3 ± 3.7 kJ/m2) at 70 % RH. Furthermore, the possible toughening mechanism of DC-Sph film was also discussed.

Ionic Conductive Cellulose-Based Hydrogels with Superior Long-Lasting Moisture and Antifreezing Features for Flexible Strain Sensor Applications

Nowadays, wearable devices derived from flexible conductive hydrogels have attracted enormous attention. Nevertheless, the utilization of conductive hydrogels in practical applications under extreme conditions remains a significant challenge. Herein, a series of inorganic salt-ion-enhanced conductive hydrogels (HPE-LiCl) consisting of hydroxyethyl cellulose, hydroxyethyl acrylate, lithium chloride, and ethylene glycol/water binary solvent were fabricated via a facile one-pot method. Apart from outstanding self-adhesion, high stretchability, and remarkable fatigue resistance, the HPE-LiCl hydrogels possessed especially excellent antifreezing and long-lasting moisture performances, which could maintain satisfactory flexibility and electric conductivity over extended periods of time, even in challenging conditions such as extremely low temperatures (as low as -40 °C) and high temperatures (as high as 80 °C). Consequently, the HPE-LiCl-based sensor could timely and accurately monitor various human motion signals even in adverse environments and after long-term storage. Hence, this work presents a facile strategy for the design of long-term reliable hydrogels as smart strain sensors, especially used in extreme environments.

Controllable and Reversible Assembly of Nanofiber from Natural Macromolecules via Protonation and Deprotonation

Nanofiber is the critical building block for many biological systems to perform various functions. Artificial assembly of molecules into nanofibers in a controllable and reversible manner will create "smart" functions to mimic those of their natural analogues and fabricate new functional materials, but remains an open challenge especially for nature macromolecules. Herein, the controllable and reversible assembly of nanofiber (CSNF) from natural macromolecules with oppositely charged groups are successfully realized by protonation and deprotonation of charged groups. By controlling the electrostatic interaction via protonation and deprotonation, the size and morphology of the assembled nanostructures can be precisely controlled. A strong electrostatic interaction contributes to large nanofiber with high strength, while poor electrostatic interaction produces finer nanofiber or nanoparticle. And especially, the assembly, disassembly, and reassembly of the nanofiber occurs reversibly through protonation and deprotonation, thereby paving a new way for precisely controlling the assembly process and structure of nanofiber. The reversible assembly allows the nanostructure to dynamically reorganize in response to subtle perturbation of environment. The as-prepared CSNF is mechanical strong and can be used as a nano building block to fabricate high-strength film, wire, and straw. This study offers many opportunities for the biomimetic synthesis of new functional materials.

Effects of Hydroxyethyl Cellulose and Sulfated Rice Bran Polysaccharide Coating on Quality Maintenance of Cherry Tomatoes during Cold Storage

Cherry tomatoes are easily damaged due to their high moisture content. A composite coating was developed to delay deterioration and prolong storage by mixing antibacterial sulfated rice bran polysaccharides (SRBP) and edible hydroxyethyl cellulose (HEC) with film-forming properties. The effects of HEC, HEC-5% SRBP, and HEC-20% SRBP preservative coatings on the maintenance of the quality of cherry tomatoes (LycopersivonesculentumMill., Xiaohuang F2) during cold storage were investigated. The HEC-20% SRBP coating significantly reduced tomato deterioration and weight loss, delayed firmness loss, decreased polyphenol oxidase activity, and increased peroxidase activity. Furthermore, cherry tomatoes treated with HEC-20% SRBP maintained high levels of titratable acid, ascorbic acid, total phenols, and carotenoids. Cherry tomatoes coated with HEC-SRBP also had higher levels of volatile substances and a greater variety of these substances compared to uncoated tomatoes. In conclusion, the HEC-20% SRBP coating effectively delayed deterioration and preserved cherry tomatoes' nutrient and flavor qualities during postharvest cold storage, suggesting it could be a novel food preservation method.

An evaluation of antibacterial properties and cytotoxicity of UV-curable biocompatible films containing hydroxyethyl cellulose and silver nanoparticles

The present study aimed to develop biocompatible film materials with antibacterial and anticancer properties that can be cured with UV rays depending on the thiol-en click reaction mechanism. The synthesized m-Ag NPs were added to formulations containing acrylate functionality HEC, pentaerythritol tetrarkis(3-mercaptopropionate), and photoinitiator at different rates (0, 20, 40, and 60 parts per hundred (phr)). The antibacterial activity of the films was evaluated against S. aureus, P. aeruginosa and E. coli by the disk diffusion test. The antibacterial effect of the films did not form an inhibition zone for the control formulation (CmAg0) against bacteria whereas the antibacterial property increased as the Ag NPs content increased in formulations containing m-Ag NPs. The strongest resistance film against the three bacterial species was observed in the CmAg60 formulation with 60 phr silver content, and the inhibition zones for S. aureus, P. aeruginosa, and E. coli were measured as 16.5 ± 0.7, 16.5 ± 2.1, and 16 ± 1.4, respectively. The cytotoxicity of the films against healthy cells and breast cancer cell (MCF-7) lines was investigated with MTT, and it was observed that all films did not cause any inhibition in the structure of the living cell but killed the cells at a high rate in the MCF-7 line. It was mainly observed that the CmAg60 formulation showed 95.576 % cell inhibition against MCF-7. According to these results, it has been predicted that the prepared films will play a vital role in the next generation of cancer treatments.

Cellulose nanocrystalline from biomass wastes: An overview of extraction, functionalization and applications in drug delivery

Cellulose nanocrystals (CNC) have been extensively used in various fields due to their renewability, excellent biocompatibility, large specific surface area, and high tensile strength. Most biomass wastes contain significant amounts of cellulose, which forms the basis of CNC. Biomass wastes are generally made up of agricultural waste, and forest residues, etc. CNC can be produced from biomass wastes by removing the non-cellulosic components through acid hydrolysis, enzymatic hydrolysis, oxidation hydrolysis, and other mechanical methods. However, biomass wastes are generally disposed of or burned in a random manner, resulting in adverse environmental consequences. Hence, using biomass wastes to develop CNC-based carrier materials is an effective strategy to promote the high value-added application of biomass wastes. This review summarizes the advantages of CNC applications, the extraction process, and recent advances in CNC-based composites, such as aerogels, hydrogels, films, and metal complexes. Furthermore, the drug release characteristics of CNC-based material are discussed in detail. Additionally, we discuss some gaps in our understanding of the current state of knowledge and potential future directions of CNC-based materials.

Wet-spinnability and crosslinked Fiber properties of alginate/hydroxyethyl cellulose with varied proportion for potential use in tendon tissue engineering

Researchers have examined different bio-inspired materials in tissue engineering and regenerative medicine to fabricate scaffolds to address tendon regeneration requirements. We developed fibers based on alginate (Alg) and hydroxyethyl cellulose (HEC) by wet-spinning technique to mimic the fibrous sheath of ECM. Various proportions (25:75, 50:50, 75:25) of 1 % Alg and 4 % HEC were blended to this aim. Two steps of crosslinking with different concentrations of CaCl₂ (2.5 and 5 %) and glutaraldehyde (2.5 %) were used to improve physical and mechanical properties. The fibers were characterized by FTIR, SEM, swelling, degradation, and tensile tests. The in vitro proliferation, viability, and migration of tenocytes on the fibers were also evaluated. Moreover, the biocompatibility of implanted fibers was investigated in an animal model. The results showed ionic and covalent molecular interactions between the components. In addition, by properly maintaining surface morphology, fiber alignment, and swelling, lower concentrations of HEC in the blending provided good degradability and mechanical features. The mechanical strength of fibers was in the range of collagenous fibers. Increasing the crosslinking led to significantly different mechanical behaviors in terms of tensile strength and elongation at break. Because of good in vitro and in vivo biocompatibility, tenocyte proliferation, and migration, the biological macromolecular fibers could serve as desirable tendon substitutes. This study provides more practical insight into tendon tissue engineering in translational medicine.

A Comparison of Unmodified and Sawdust Derived-Cellulose Nanocrystals (CNC)-Modified Polyamide Membrane Using X-ray Photoelectron Spectroscopy and Zeta Potential Analysis

Cellulose nanocrystals (CNC) obtained from waste sawdust were used to modify the polyamide membrane fabricated by interfacial polymerization of m-phenylene-diamine (MPDA) and trimesoyl chloride (TMC). The efficiency of the modification with sawdust-derived CNC was investigated using zeta potential and X-ray photoelectron spectroscopy (XPS). The effect of the modification on membrane mechanical strength and stability in acidic and alkaline solutions was also investigated. Results revealed that the negative zeta potential decreased at a high pH and the isoelectric point shifted into the acidic range for both modified and unmodified membranes. However, the negative charges obtained on the surface of the modified membrane at a pH lower than 8 were higher than the pristine membrane, which is an indication of the successful membrane modification. The XPS result shows that the degree of crosslinking was lowered due to the presence of CNC. Enhanced stability in solution in all pH ranges and the increase in mechanical strength, as indicated by higher Young's modulus, maximum load, and tensile strength, confirmed the robustness of the modified membrane.

Development of functional hydroxyethyl cellulose-based composite films for food packaging applications

Cellulose-based functional composite films can be a good substitute for conventional plastic packaging to ensure food safety. In this study, the semi-transparent, mechanical strengthened, UV-shielding, antibacterial and biocompatible films were developed from hydroxyethyl cellulose Polyvinyl alcohol (PVA) and ε-polylysine (ε-PL) were respectively used as reinforcing agent and antibacterial agent, and chemical cross-linking among these three components were constructed using epichlorohydrin The maximum tensile strength and elongation at break were 95.9 ± 4.1 MPa and 148.8 ± 2.6%, respectively. TG-FTIR and XRD analyses indicated that chemical structure of the composite films could be well controlled by varying component proportion. From UV-Vis analysis, the optimum values of the percentage of blocking from UV-A and UV-B and ultraviolet protection factor values were 98.35%, 99.99% and 60.25, respectively. Additionally, the composite films exhibited good water vapor permeability, swelling behavior, antibacterial activity and biocompatibility. In terms of these properties, the shelf life of grapes could be extended to 6 days after packing with the composite film.

All-Cellulose Composite Laminates Made from Wood-Based Textiles: Effects of Process Conditions and the Addition of TEMPO-Oxidized Nanocellulose

All-cellulose composites (ACCs) are manufactured using only cellulose as a raw material. Biobased materials are more sustainable alternatives to the petroleum-based composites that are used in many technical and life-science applications. In this study, an aquatic NaOH-urea solvent system was used to produce sustainable ACCs from wood-based woven textiles with and without the addition of TEMPO-oxidized nanocellulose (at 1 wt.-%). This study investigated the effects of dissolution time, temperature during hot press, and the addition of TEMPO-oxidized nanocellulose on the mechanical and thermal properties of the composites. The results showed a significant change in the tensile properties of the layered textile composite at dissolution times of 30 s and 1 min, while ACC elongation was the highest after 2 and 5 min. Changes in hot press temperature from 70 °C to 150 °C had a significant effect: with an increase in hot press temperature, the tensile strength increased and the elongation at break decreased. Incorporating TEMPO-oxidized nanocellulose into the interface of textile layers before partial dissolution improved tensile strength and, even more markedly, the elongation at break. According to thermal analyses, textile-based ACCs have a higher storage modulus (0.6 GPa) and thermal stabilization than ACCs with nanocellulose additives. This study highlights the important roles of process conditions and raw material characteristics on the structure and properties of ACCs.

Nanoengineering and green chemistry-oriented strategies toward nanocelluloses for protein sensing

As one of the most important functional organic macromolecules of life, proteins not only participate in the cell metabolism and gene regulation, they also earnestly protect the body's immunity system, leading to a powerful biological shield and homeostasis. Advances in nanomaterials are boosting the significant progress in various applications, including the sensing and examination of proteins in trace amount. Nanocellulose-oriented protein sensing is at the forefront of this revolution. The inherent feature of high biocompatibility, low cytotoxicity, high specific area, good durability and marketability endow nanocellulose with great superiority in protein sensing. Here, we highlight the recent progress of protein sensing using nanocellulose as the biosensor in trace amount. Besides, various kinds of construction strategies for nanocelluloses-based biosensors are discussed in detail, to enhance the agility and accuracy of clinical/medical diagnostics. Finally, several challenges in the approbatory identification of new approaches for the marketization of biomedical sensing that need further expedition in the future are highlighted.

Intelligent high-tech coating of natural biopolymer layers

Polymeric materials play a vital role in our daily life, but the growing concern for the environment demands economical and natural biopolymers that can be cross-linked to create technologically innovative lightweight materials. Their cellular matrix with extreme flexibility makes them highly acceptable for application prospects in material science, engineering, and biomedical applications. Furthermore, their biocompatibility, mechanical properties, and structural diversity provide a gateway to research them to form technologically important materials. In the light of the same, the review covers cellulose derivatives. The first section of the study covers the general properties and applications of cellulose and its derivatives. Then, the biopolymers are characterised based on their dielectric properties, crystallinity, rheology, and mechanical properties. An in-depth analysis of the diffuse process of swelling and dissolution followed by a brief discussion on diffusion and diffusion of crosslinking has been done. The review also covers a section on swelling and swelling kinetics of carboxymethyl cellulose (CMC) and hydroxyethyl cellulose (HEC). The examination of all the aforementioned parameters gives an insight into the future aspects of the biopolymers. Lastly, the study briefly covers some preferred choices of cross-linking agents and their effect on the biopolymers.

Drug Delivery Platforms Containing Thermoresponsive Polymers and Mucoadhesive Cellulose Derivatives: A Review of Patents

Nowadays, the development of mucoadhesive systems for drug delivery has gained keen interest, with enormous potential in applications through different routes. Mucoadhesion characterizes an attractive interaction between the pharmaceutical dosage form and the mucosal surface. Many polymers have shown the ability to interact with mucus, increasing the residence time of local and/or systemic administered preparations, such as tablets, patches, semi-solids, and micro and nanoparticles. Cellulose is the most abundant polymer on the earth. It is widely used in the pharmaceutical industry as an inert pharmaceutical ingredient, mainly in its covalently modified forms: methylcellulose, ethylcellulose, hydroxyethyl cellulose, hydroxypropyl cellulose, hydroxypropyl methylcellulose, and carboxymethylcellulose salts. Aiming to overcome the drawbacks of oral, ocular, nasal, vaginal, and rectal routes and thereby maintaining patient compliance, innovative polymer blends have gained the interest of the pharmaceutical industry. Combining mucoadhesive and thermoresponsive polymers allows for simultaneous in situ gelation and mucoadhesion, thus enhancing the retention of the system at the site of administration and drug availability. Thermoresponsive polymers have the ability to change physicochemical properties triggered by temperature, which is particularly interesting considering the physiological temperature. The present review provides an analysis of the main characteristics and applications of cellulose derivatives as mucoadhesive polymers and their use in blends together with thermoresponsive polymers, aiming at platforms for drug delivery. Patents were reviewed, categorized, and discussed, focusing on the applications and pharmaceutical dosage forms using this innovative strategy. This review manuscript also provides a detailed introduction to the topic and a perspective on further developments.

Fabrication of super-high transparent cellulose films with multifunctional performances via postmodification strategy

A transparent versatile cellulose platform film was prepared from Eucalyptus pulp in this work. Based on such cellulose platform, multifunctional cellulose films with ultraviolet-shielding, photochromism, and strong mechanical strength were fabricated via nucleophilic postmodification strategy by introducing a versatile spiropyran moiety into cellulose molecules. The fabricated cellulose films exhibited super-high transmittance up to 96% and performed notable ultraviolet-shielding capacity at 200-400 nm. Moreover, the photochromic performance of cellulose films with color changes could be clearly observed by the naked eyes, and the fluorescent blue could be excited. Besides, the tensile stress of multi-functional cellulose film was about 80 MPa, which was almost 8 times stronger than that of the commercial polyethylene film at the same thickness. It is noteworthy that these superior performances promote such a cellulose platform to be a versatile precursor for fabricating various multi-functional cellulose used in the fields of out-door coating, transparent packaging, optical screen,etc.

Preparation and Characterization of a Sol–Gel AHEC Pore-Sealing Film Prepared on Micro Arc Oxidized AZ31 Magnesium Alloy

The purpose of this study was to improve the cellular compatibility and corrosion resistance of AZ31 magnesium alloy and to prepare a biodegradable medical material. An aminated hydroxyethyl cellulose (AHEC) coating was successfully prepared on the surface of a micro-arc oxide +AZ31 magnesium alloy by sol–gel spinning. The pores of the micro-arc oxide coating were sealed. A polarization potential test analysis showed that compared to the single micro-arc oxidation coating, the coating after sealing with AHEC significantly improved the corrosion resistance of the AZ31 magnesium alloy and reduced its degradation rate in simulated body fluid (SBF). The CCK-8 method and cell morphology experiments showed that the AHEC + MAO coating prepared on the AZ31 magnesium alloy had good cytocompatibility and bioactivity.

Improved mechanical and ultraviolet shielding performances of hydroxyethyl cellulose film by using aramid nanofibers as additives

Recently, aramid nanofibers (ANFs) have drawn the attention of scientist due to the high mechanical strength, high-temperature resistance, and high electrical and thermal insulation properties. In this work, we aimed at improving the mechanical and ultraviolet shielding properties of hydroxyethyl cellulose (HEC) film by using ANFs as additives. Mechanical results show that the 1.0 % ANFs could improve the tensile strength of pure HEC film by 176.6 %. Meanwhile, the ANFs additives can also enable the HEC film excellent ultraviolet (UV) shielding and visible light transmittance, as well as high UV radiation resistance ability. It is believed that the high mechanical strength of the HEC/ANFs composites is derived from the rearrangement of HEC chains along the tensile direction after the addition of hard ANFs and the enhanced hydrogen bonds between HEC and ANFs.

Highly compressible, heat-insulating and self-extinguishing cellulose nanofiber/aramid nanofiber nanocomposite foams

Foam as a kind of burgeoning materials with laminated porous 3D structure was realized multifunctional application in diversified fields. In this work, we aimed to prepare a highly compressible and self-extinguishing multifunctional nanocomposite foam with anisotropic porous 3D structure through a green aqueous freeze-drying method. In order to address the inflammable property and brittleness issue of high-loading cellulose nanofiber foam, aramid nanofiber was incorporated into cellulose nanofiber framework, forming the multicomponent and multilevel honeycomb structure of the nanocomposite foam. Herein, the compression cycle properties of the nanocomposite foam could be significantly improved by adding 50 wt.% aramid nanofiber and at 20% stress recovered by 100 % even if cyclically compressed 200 times. The total heat release of the nanocomposite foam was as low as 2.12 MJ/m² which also had low thermal conductivity about 28.8 mW/m · K. The ANF improved the flame retardancy of the composite foam.