Functional chitosan/glycidyl methacrylate-based cryogels for efficient removal of cationic and anionic dyes and antibacterial applications

Preparation of poly(l-lactic acid) antibacterial film based on surface grafting of modified chitosan and its preservation effect on chilled beef

Chilled beef is a perishable food product. Due to the broad-spectrum antimicrobial properties of chitosan, and the biodegradability of PLLA, chitosan and PLLA are introduced double bonding groups to obtain Chitosan-graft-Glycidyl methacrylate (Cs-g-GMA) and Poly(L-lactic acid)-co-poly(butylene itaconate) (PLBI), respectively. Cs-g-GMA is then grafted onto the surface of PLBI films by UV curing to produce PLBI/Cs-g-GMA films with non-migratory, broad-spectrum antimicrobial, biodegradable, and possess good oxygen barrier properties, compared to current antimicrobial films. Antimicrobial tests in vitro confirmed that PLBI/Cs-g-GMA film could effectively inhibit the growth and reproduction of P. fluorescens, S. aureus, and E. coli. The PLBI/Cs-g-GMA films were further used for the packaging of chilled beef during 15 days of refrigerated storage. The microbiological (total viable counts (TVC), microbial diversity analysis), physicochemical (pH, total volatile basic nitrogen (TVB-N), drip loss, color) and sensory of beef were measured to evaluate the preservation effect. The results showed that PLBI/Cs-g-GMA films can significantly inhibit Pseudomonas and Aeromonas at the phylum and genus levels, respectively. Based on the good results of the preservation index, PLBI/Cs-g-GMA film could delay the quality deterioration of chilled beef by 3 to 9 days, suggesting that its considerable prospects for maintaining the storage quality of chilled beef.

Experimental and computational study of removal of methyl green and eosin yellow from aqueous solutions using novel sulfamic and sulfanilic acid grafted chitosan-epichlorohydrin -Fe2O3 nanocomposites

Two novel chitosan-based adsorbents, sulfamic acid-chitosan-epichlorohydrin-Fe2O3 (HK-1) and sulfanilic acid-chitosan-epichlorohydrin-Fe2O3 (HK-2), were successfully synthesized and characterized by XRD, TGA, DSC, BET, and SEM techniques. The ability of the synthesized adsorbents for removing cationic Methyl Green (MG) and anionic Eosin Yellow (EY) from aqueous solutions was investigated at different solution pHs, adsorbent dosages, and contact times. The results showed a removal efficiency of 93.5 % and 96.8 % for adsorbing cationic MG respectively by HK-1 and HK-2 at pH = 8. The removal efficiency for adsorbing anionic EY by HK-1 and HK-2 was respectively 90.8 % and 94.6 % at pH = 3. The results also showed that >50 % of MG was adsorbed within the first 30 min of contact with HK-1 and HK-2, but it took about 75 and 45 min to adsorb 50 % of EY respectively by HK-1 and HK-2. DFT calculations confirmed the spontaneous adsorption of EY and MG on the surface of HK-1 and HK-2. These promising results suggest that HK-1 and HK-2 can be used to remove other cationic and anionic dyes from aqueous solutions.

A novel macroporous carboxymethyl chitosan/sodium alginate sponge dressing capable of rapid hemostasis and drug delivery

Carboxymethyl chitosan (CMCS) and sodium alginate (SA), which are excellent polysaccharide-based hemostatic agents, are capable of forming polyelectrolyte complexes (PEC) through electrostatic interactions. However, CMCS/SA PEC sponges prepared by the conventional sol-gel process exhibited slow liquid absorption rate and poor mechanical properties post-swelling. In this work, a novel strategy involving freeze casting followed by acetic acid vapor treatment to induce electrostatic interactions was developed to fabricate novel PEC sponges with varying CMCS/SA mass ratios. Compared to sol-gel process sponge, the novel sponge exhibited a higher density of electrostatic interactions, resulting in denser pore walls that resist re-gelation and swelling according to FTIR, XRD, and SEM analyses. Additionally, the liquid absorption kinetics, as well as compression and tension tests, demonstrated that the novel sponge had significantly improved rapid blood absorption capacity and mechanical properties. Furthermore, in vitro coagulation and drug release studies showed that the novel sponge had a lower blood clotting index and clotting time, along with a slower drug release rate after loading with berberine hydrochloride, showcasing its potential as a rapid hemostatic dressing with controlled drug release capabilities.

Cellulose-citric acid-chitosan@metal sulfide nanocomposites: Methyl orange dye removal and antibacterial activity

In this study, to develop efficient adsorbents in removing water pollution, new cellulose-citric acid-chitosan@metal sulfide nanocomposites (CL-CA-CS@NiS and CL-CA-CS@CuS) were synthesized by one-pot reaction at mild conditions and characterized using X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscope (SEM), Energy Dispersive X-ray (EDX) and Brunauer-Emmett-Teller (BET) isotherm. The results of characterization techniques confirm that the desired compounds have been successfully synthesized. The as-prepared composites were applied for the removal of methyl orange (MO) dye from aqueous solutions using a batch technique, and the effect of key factors such as initial pH, shaking time, MO concentration, temperature and adsorbent dose were investigated and discussed. Adsorption results exhibited positive impact of temperature, shaking time and adsorbent dose on the MO removal percent. The MO removal percent has been increased over a wide range of pH from 2 (27.6 %) to 6 (98.8 %). Also, almost being constant over a wide range of MO concentration (10-70 mg/L). The results demonstrated that the maximum removal percentage of MO dye (98.9 % and 93.4 % using CL-CA-CS@NiS and CL-CA-CS@CuS, respectively) was achieved under the conditions of pH 6, shaking time of 120 min, adsorbent dose of 0.02 g, MO concentration of 70 mg/L and temperature of 35 °C. The pseudo-second-order (PSO) and Langmuir models demonstrated the best fit to the kinetic and equilibrium data. Also, the thermodynamic results showed that the MO removal process is endothermic and spontaneous in nature. The MO adsorption can be happened by different electrostatic attraction, n-π and π-π stacking and also hydrogen bonding interaction. In addition, antibacterial activity of CL-CA-CS@NiS and CL-CA-CS@CuS nanocomposites exhibited a superior efficiency against S. aureus.

Environmentally Benign Freeze-dried Biopolymer-Based Cryogels for Textile Wastewater Treatments: A review

Motivated by sustainability and environmental protection, great efforts have been paid towards water purification and attaining complete decolorization and detoxification of polluted water effluent. Textile effluent, the main participant in water pollution, is a complicated mixture of toxic pollutants which seriously impact human health and the entire ecosystem. Developing effective materials for potential removal of the water contaminants is urgent. Recently, cryogels have been applied in wastewater sectors due to their unique physiochemical attributes(e.g. high surface area, lightweight, porosity, swelling-deswelling, and high permeability). These features robustly affected the cryogel's performance, as adsorbent material, particularly in wastewater sectors. This review serves as a detailed reference to the cryogels derived from biopolymers and applied as adsorbents for the purification of textile drainage. We displayed an overview of: the existing contaminants in textile effluents (dyes and heavy metals), their sources, and toxicity; advantages and disadvantages of the most common treatment techniques (biodegradation, advanced chemical oxidation, membrane filtration, coagulation/flocculation, adsorption). A simple background about cryogels (definition, cryogelation technique, significant features as adsorbents, and the adsorption mechanisms) is also discussed. Finally, the bio-based cryogels dependent on biopolymers such as chitosan, xanthan, cellulose, PVA, and PVP, are fully discussed with evaluating their maximum adsorption capacity.

Compressive elasticity of epoxy functionalized Chitosan-based semi-IPN cryobeads of N-alkyl methacrylate esters: Validity of the Hertzian model with experiments

In situ forming poly(dimethylaminoethyl methacrylate-co-glycidylmethacrylate)/Chitosan, P(DMAEMA-co-GMA)/Chitosan, (PDG/CS) cryobeads based on "dropwise freezing into cryogenic liquid method" combined with "blending with polymer method" are promising for applications due to their pH-responsiveness and stability under physiological conditions. Based on classical contact mechanics, Hertzian elasticity of semi-interpenetrated network (semi-IPN) cryobeads was analyzed to examine whether there is a direct correlation between elastic properties of single particle and its macroscopic behavior. A one-step procedure has been proposed to design chitosan-interpenetrated cryobeads with a cationic nature via combination of structural properties as well as functionality of chitosan containing primary and secondary hydroxyl and amino groups. The study is focused on characterization of network formation kinetics in different shapes and how different production variables affect the elasticity/swelling performance of cross-linked system. The elastic properties of semi-IPN cryobeads were improved by both adding chitosan to copolymer PDG structure and lowering the gelation temperature to cryogelation conditions. The results obtained highlighted the importance of composition to modulate elasticity, the influence of preparation temperature and shape of cryobeads on their elasticity. Findings regarding the topography-dependent local elastic properties of chitosan-incorporated semi-IPN gels offer possibilities for modulating the behavior of chitosan-based soft materials.

Biomaterial-based sponge for efficient and environmentally sound removal of bacteria from water

Designing materials capable of disinfecting water without releasing harmful by-products is an ongoing challenge. Here, we report a novel polycationic sponge material synthesized from chitosan derivatives and cellulose fibers, exhibiting antibacterial properties. The design of such material is based on three key principles. First, the formation of a highly porous structure through cryogelation for an extensive surface area. Second, the incorporation of cationic quaternary ammonium moieties onto chitosan to enhance bacterial adsorption and antibacterial activity. Lastly, the reinforcement of mechanical properties through integration of cellulose fibers. The presented sponge materials exhibit up to a 4-log (99.99%) reduction within 6 h against both gram-positive B. subtilis and gram-negative E. coli. Notably, QCHI90/Cell, with the highest surface charge, exhibits a 2-4.5 log reduction within 1 h of incubation time. The eco-friendly synthesis from water and readily available biomaterials, along with cost-effectiveness and simplicity, underscores its versatility and feasibility of upscaling. Together with its outstanding antibacterial activity, this macroporous biomaterial emerges as a promising candidate for water disinfection applications.

Ion-imprinted chitosan prepared without cross-linking agent for efficient selective adsorption of Al(III) from rare earth solution

In the aqueous phase, ion-imprinted materials exhibit excellent selective adsorption properties for specific ions, but their complicated preparation process and large amount of crosslinker consumption limit their application. In this study, ion-imprinted chitosan (IIP-CS) was prepared by a simple one-step hydrothermal method without a cross-linking agent for the efficient adsorption of trace amounts of Al(III) from a rare earth solution. The structures and morphology of IIP-CS were analyzed by FT-IR, SEM, and XRD. The Al(III) adsorption characteristics of IIP-CS were investigated under various preparation processes and adsorption conditions. It was found that the optimum mass ratio of IIP-CS is 3 : 1 and pH is 3 and the adsorption capacity reaches up to 40.36 mg g-1. In addition, three different isothermal models-Temkin, Freundlich, and Langmuir-were used to analyze the equilibrium adsorption of IIP-CS in aqueous solution. The results obtained are consistent with the Langmuir model. The adsorption process of Al(III) on IIP-CS follows a pseudo-secondary kinetic model, suggesting that electron sharing or exchange between IIP-CS and Al(III) is a key factor affecting its adsorption rate. IIP-CS shows high selectivity coefficients for Al(III) in mixtures of La(III), Y(III), and Gd(III), which are 792.50, 163.26, and 55.16, respectively. The mechanism of action is the formation of a complex via amidation between Al(III) and IIP-CS. IIP-CS is an adsorbent with excellent regeneration and selective adsorption performance in aqueous solution.

Surface modifications of biopolymers for removal of per- and polyfluoroalkyl substances from water: Current research and perspectives

Per- and polyfluoroalkyl substances (PFAS) are highly recalcitrant organic contaminants that have attracted ever-increasing attention from the general public, government agencies and scientific communities. To remove PFAS from water, especially the enormous volume of drinking water, stormwater, and groundwater, sorption is the most practical approach. Success of this approach demands green, renewable, and sustainable materials for capturing PFAS at ng/L or µg/L levels. To meet this demand, this manuscript critically reviewed sorbents developed from biopolymers, such as chitosan (CTN), alginate (ALG), and cellulose (CEL) covering the period from 2008 to 2023. The use of different cross-linkers for the surface modifications of biopolymers were described. The underlying removal mechanism of biosorbents for PFAS adsorption from molecular perspectives was discussed. Besides reviewing and comparing the performance of different bio-based sorbents with respect to environmental factors like pH, and sorption kinetics and capacity, strategies for modifying biosorbents for better performance were proposed. Additionally, approaches for regeneration and reuse of the biosorbents were discussed. This was followed by further discussion of challenges facing the development of biosorbents for PFAS removal.

NaBiS2 decorated polysaccharide sponges for adsorption-photocatalytic degradation of dye under visible light illumination

Dye is emissions aggravating aquatic ecosystem pollution, and photocatalysis is considered the most appealing option to remove dyes by degradation. However, the current photocatalysts suffer from agglomeration, large bandgaps, high mass transfer resistance, and high operation cost. Herein, we present a facile hydrothermally induced phase separation and in situ synthesis strategy for fabrication of sodium bismuth sulfide (NaBiS₂)-decorated chitosan/cellulose sponges (NaBiCCSs). The NaBiCCSs demonstrate unique polysaccharide cellular structure (150-500 μm), uniformly immobilized NaBiS₂ nanoparticles (70-90 nm), narrow bandgap (1.18 eV), high photocurrent (0.74 μA/cm²), and outstanding compressibility. Benefiting from the characteristics and the high affinity to dyes, the NaBiCCSs provide innovative synergistic adsorption-photocatalytic degradation model for dye removal, attaining a superior methylene blue removal rate of 98.38 % under visible light illumination and offering good reusability. This study offers a sustainable technical solution for dye contaminant removal.

Polyelectrolyte and polyelectrolyte complex-incorporated adsorbents in water and wastewater remediation - A review of recent advances

In recent years, polyelectrolyte-incorporated functional materials have emerged as novel adsorbents for effective remediation of pollutants in water and wastewater. Polyelectrolytes (PEs) are a special class of polymers with long chains of repeating charged moieties. Polyelectrolyte complexes (PECs) are obtained by mixing aqueous solutions of oppositely charged PEs. Herewith, this review discusses recent advances with respect to water and wastewater remediation using PE- and PEC-incorporated adsorbents. The review begins by highlighting some water resources, their pollution sources and available treatment techniques. Next, an overview of PEs and PECs is discussed, highlighting the evolving progress in their processing. Consequently, application of these materials in different facets of water and wastewater remediation, including heavy metal removal, precious metal and rare earth element recovery, desalination, dye and emerging micropollutant removal, are critically reviewed. For water and wastewater remediation, PEs and PECs are mostly applied either in their original forms, as composites or as morphologically-tunable complexes. PECs are deemed superior to other materials owing to their tunability for both cationic and anionic pollutants. Generally, natural and semi-synthetic PEs have been largely applied owing to their low cost, ready availability and eco-friendliness. Except dye removal and desalination of saline water, application of synthetic PEs and PECs is scanty, and hence requires more focus in future research.

A Comprehensive Review on Adsorption, Photocatalytic and Chemical Degradation of Dyes and Nitro-Compounds over Different Kinds of Porous and Composite Materials

Dye and nitro-compound pollution has become a significant issue worldwide. The adsorption and degradation of dyes and nitro-compounds have recently become important areas of study. Different methods, such as precipitation, flocculation, ultra-filtration, ion exchange, coagulation, and electro-catalytic degradation have been adopted for the adsorption and degradation of these organic pollutants. Apart from these methods, adsorption, photocatalytic degradation, and chemical degradation are considered the most economical and efficient to control water pollution from dyes and nitro-compounds. In this review, different kinds of dyes and nitro-compounds, and their adverse effects on aquatic organisms and human beings, were summarized in depth. This review article covers the comprehensive analysis of the adsorption of dyes over different materials (porous polymer, carbon-based materials, clay-based materials, layer double hydroxides, metal-organic frameworks, and biosorbents). The mechanism and kinetics of dye adsorption were the central parts of this study. The structures of all the materials mentioned above were discussed, along with their main functional groups responsible for dye adsorption. Removal and degradation methods, such as adsorption, photocatalytic degradation, and chemical degradation of dyes and nitro-compounds were also the main aim of this review article, as well as the materials used for such degradation. The mechanisms of photocatalytic and chemical degradation were also explained comprehensively. Different factors responsible for adsorption, photocatalytic degradation, and chemical degradation were also highlighted. Advantages and disadvantages, as well as economic cost, were also discussed briefly. This review will be beneficial for the reader as it covers all aspects of dye adsorption and the degradation of dyes and nitro-compounds. Future aspects and shortcomings were also part of this review article. There are several review articles on all these topics, but such a comprehensive study has not been performed so far in the literature.

Effects of degree of deacetylation on hemostatic performance of partially deacetylated chitin sponges

Chitin/chitosan hemostatic materials have long been studied for uncontrolled hemorrhage, an urgent clinical problem due to severe blood-vessel damage or hemophilia. As one of the basic structural parameters of chitin, the degree of deacetylation (DD) significantly affects the material's physical, chemical, as well as biological properties. In this study, partially deacetylated chitins with a wide range of DD (23-81%) were prepared by homogeneous deacetylation, and sponges with these various chitins were fabricated by freeze-drying to study the effects of DD on their hemostatic properties. Among all sponge samples, the chitosan sponge with a DD of 48% showed the highest water absorption, whole blood adsorption, RBC adsorption rate, and the best hemostatic performance in an uncontrolled bleeding model of the rat femoral artery, demonstrating that a certain proportion of acetyl amino and amino groups could also activate the coagulation system and promote the adhesion of platelet and erythrocyte.

Chitosan coated Fe3O4@Cd-MOF microspheres as an effective adsorbent for the removal of the amoxicillin from aqueous solution

In this work, for the first time, a new magnetic cadmium-based MOFs (Fe₃O₄@Cd-MOF) was successfully synthesized in a green way and then modified with chitosan (CS) in the microsphere form (Fe₃O₄@Cd-MOF@CS). The obtained materials were fully characterized by several techniques. In the following, the efficiency of Fe₃O₄@Cd-MOF@CS was explored for the removal of amoxicillin (AMX). The outcome of the adsorption study showed that the removal efficiency is affected by CS and reaches its optimum at pH 8 and contact time of 240 min. Under optimized conditions, over 75% of AMX was removed. The kinetic and the isotherm of the adsorption were fit with the pseudo-second-order model and the Langmuir adsorption isotherm respectively. Eventually, the maximum adsorption capacity was obtained ~103.09 mg/g. Interestingly, these findings convince that the newly prepared Fe₃O₄@Cd-MOF@CS could be proposed as a promising magnetically separable adsorbent for antibiotic contaminants removal from the aqueous solution.

Chitosan Functionalization: Covalent and Non-Covalent Interactions and Their Characterization

Chitosan (CS) is a natural biopolymer that has gained great interest in many research fields due to its promising biocompatibility, biodegradability, and favorable mechanical properties. The versatility of this low-cost polymer allows for a variety of chemical modifications via covalent conjugation and non-covalent interactions, which are designed to further improve the properties of interest. This review aims at presenting the broad range of functionalization strategies reported over the last five years to reflect the state-of-the art of CS derivatization. We start by describing covalent modifications performed on the CS backbone, followed by non-covalent CS modifications involving small molecules, proteins, and metal adjuvants. An overview of CS-based systems involving both covalent and electrostatic modification patterns is then presented. Finally, a special focus will be given on the characterization techniques commonly used to qualify the composition and physical properties of CS derivatives.