Diethylenetriaminepentaacetic acid-thiourea-modified magnetic chitosan for adsorption of hexavalent chromium from aqueous solutions

Efficient removal of chromate from wastewater using a one-pot synthesis of chitosan cross-linked ceria incorporated hydrous copper oxide bio-polymeric composite

Remediating hexavalent chromium [Cr(VI)] from contaminated water systems is a significant concern due to its harmful effects on human health, aquatic life, and plants. To tackle this issue, scientists have created a chitosan cross-linked hydrous ceria incorporated cupric oxide bio-polymeric composite (CHCCO) by combining chitosan biopolymer with corresponding metal ions using glutaraldehyde as a cross-linker. The composite was characterized using advanced analytical instruments such as FTIR, p-XRD, SEM, XPS, etc. The synthesized composite (CHCCO) was then tested for its efficiency in removing Cr(VI) from synthetic Cr(VI) aqueous samples. The parameters examined included pH, material dose, contact time, concentration, temperature, and co-existing ions. The experimental data showed that the kinetics and equilibrium data fit well with the pseudo-second-order and the Freundlich isotherm models, respectively. Thermodynamic analysis demonstrated that the investigated surface adsorption process is spontaneous and endothermic. Except for the SO42- ion, no other species imparts adverse influence significantly on the reaction. The CHCCO bio-composite surfaces were refreshed using a dilute NaOH (1.0 M) solution and effectively recycled five times for Cr(VI) adsorption, indicating no significant surface activity deterioration. This study highlights the high effectiveness of CHCCO bio-polymeric composites in Cr(VI) remediation and the potential for this technology as an easy-to-use technique for environmental restoration.

A novel chitosan-alginate@Fe/Mn mixed oxide nanocomposite for highly efficient removal of Cr (VI) from wastewater: Experiment and adsorption mechanism

In this study, the synthesis and experimental theoretical evaluation of a new chitosan/alginate/hydrozyapatite nanocomposite doped with Mn2 and Fe2O3 for Cr removal was reported. The physicochemical properties of the obtained materials were analyzed using the following methods: SEM-EDX, XRD, FTIR, XPS, pH drift measurements, and thermal analysis. The adsorption properties were estimated based on equilibrium and adsorption kinetics measurements. The Langmuir, Freundlich and Temkin isotherms were applied to analyze the equilibrium data. The thermodynamic analysis of adsorption isotherms was performed. A number of equations and kinetic models were used to describe the adsorption rate data, including pseudo-first (PFOE) and pseudo-second (PSOE) order kinetic equations. The obtained test results show that the synthesized biomaterial, compared to pure chitosan, is characterized by greater resistance to high temperatures. Moreover, this biomaterial had excellent adsorption properties. For the adsorption of Cr (VI), the equilibrium state was reached after 120 min, and the sorption capacity was 455.9 mg/g. In addition, DFT calculations and NCI analyses were performed to get more light on the adsorption mechanism of Cr (VI) on the prepared biocomposite.

Degradation of ciprofloxacin by persulfate activated by Fe(III)-doped BiOCl composite photocatalyst

Fe-BOC-X photocatalyst was successfully prepared by solvothermal method. The photocatalytic activity of Fe-BOC-X was determined by ciprofloxacin (CIP), a typical fluoroquinolone antibiotic. Under sunlight irradiation, all Fe-BOC-X showed better CIP removal performance than original BiOCl. In comparison, the photocatalyst with iron content of 50 wt% (Fe-BOC-3) has excellent structural stability and the best adsorption photodegradation efficiency. The removal rate of CIP (10 mg/L) by Fe-BOC-3 (0.6 g/L) reached 81.4% within 90 min. At the same time, the effects of photocatalyst dosage, pH, persulfate, persulfate concentration, and combinations of different systems (PS, Fe-BOC-3, Vis/PS, Vis/Fe-BOC-3, Fe-BOC-3/PS, and Vis/Fe-BOC-3/PS) on the reaction were systematically discussed. In reactive species trapping experiments, electron spin resonance (ESR) signals revealed that the photogenerated holes (h+), hydroxyl radical (•OH), sulfate radical (•SO4-), and superoxide radical (•O2-) played an important role in CIP degradation; hydroxyl radicals (•OH) and sulfate radicals (•SO4-) play a major role. Various characterization methods have demonstrated that Fe-BOC-X has larger specific surface area and pore volume than original BiOCl. UV-vis DRS indicate that Fe-BOC-X has wider visible light absorption and faster photocarrier transfer and provides abundant surface oxygen absorption sites for effective molecular oxygen activation. Accordingly, a large number of active species were produced and participated in the photocatalytic process, thus effectively promoting the degradation of ciprofloxacin. Based on HPLC-MS analysis, two possible decomposition pathways of CIP were finally proposed. The main degradation pathways of CIP are mainly due to the high electron density of piperazine ring in CIP molecule, which is mainly attacked by various free radicals. The main reactions include piperazine ring opening, decarbonylation, decarboxylation, and fluorine substitution. This study can better open up a new way for the design of visible light driven photocatalyst and provide more ideas for the removal of CIP in water environment.

Sorption enhancement of Cr(VI) from aqueous solution by polyaniline confined in three-dimensional network of composite porous hydrogel

Hexavalent chromium Cr(VI) is a typical harmful pollutant, which is carcinogenic or mutagenic to aquatic animals and humans. In this study, sepiolite/humic acid/polyvinyl alcohol@ polyaniline (SC/HA/PVA@PANI) composite porous hydrogel adsorbent was synthesized by Pickering emulsion template in situ chemical oxidative polymerization for adsorption of Cr(VI) from aqueous solution. The in situ polymerization of aniline at the Pickering emulsion interface and the unique three-dimensional network structure of the hydrogel act as an effective "confinement" for the growth of the polymer. The porous structure of the material acts as a water channel, which effectively accelerates the binding of the adsorbate to the adsorption sites, and significantly improves the adsorption rate and adsorption capacity. The adsorption capacity of PANI for Cr(VI) confined in three-dimensional network of composite porous SC/HA/PVA@PANI hydrogel reached 1180.97 mg/g-PANI, which increased about 27-fold compared the adsorption capacity of pure PANI (43.48 mg/g). It is shown that the experimental design effectively avoids the agglomeration of PANI and improves its potential adsorption performance. In addition, the analysis of FESEM-EDX, FT-IR, and XPS spectra before and after adsorption confirmed that the main adsorption mechanisms of Cr(VI) on SC/HA/PVA@PANI included ion exchange, electrostatic attraction, and redox reaction. In conclusion, SC/HA/PVA@PANI has good stability and excellent adsorption performance, which is a new type of Cr(VI) ion adsorbent with great potential.

Preparation of biochar@chitosan-polyethyleneimine for the efficient removal of uranium from water environment

A novel chitosan-based composite with rich active sites was synthesized by uniformly dispersing biochar into the cross-linked network structure formed by chitosan and polyethyleneimine. Due to the synergistic effect of biochar (minerals) and chitosan-polyethyleneimine interpenetrating network (amino and hydroxyl), the chitosan-based composite possessed an excellent adsorption performance for uranium(VI). It could rapidly (<60 min) achieve a high adsorption efficiency (96.7 %) for uranium(VI) from water and a high static saturated adsorption capacity (633.4 mg/g), which was far superior to other chitosan-based adsorbents. Moreover, the separation for uranium(VI) on the chitosan-based composite was suitable for a variety of actual water environments and the adsorption efficiencies all exceeded 70 % in different water bodies. The soluble uranium(VI) could be completely removed by the chitosan-based composite in the continuous adsorption process, which could meet the permissible limits of the World Health Organization. In sum, the novel chitosan-based composite could overcome the bottleneck of current chitosan-based adsorption materials and become a potential adsorbent for the remediation of actual uranium(VI) contaminated wastewater.

Cellulose Modified with Polyethylenimine (PEI) Using Microwave Methodology for Adsorption of Chromium from Aqueous Solutions

A large amount of agricultural waste was used to prepare cellulose (Cel) and then the surface was modified with PEI (Cel-PEI) using the microwave method. To be used as a metal adsorbent, the adsorption of Cr (VI) from an aqueous solution by Cel-PEI was measured using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) techniques. The parameters of Cr (VI) adsorption in solution by the Cel-PEI adsorbent were as follows: the pH of the solution was 3, the concentration of the chromium solution was 100 mg/L, and the adsorption time was 180 min at 30 °C using 0.01 g of adsorbent. Cel-PEI had a Cr (VI) adsorption capacity of 106.60 mg/g, while the unadjusted Cel was 23.40 mg/g and the material recovery showed a decrease in efficiency of 22.19% and 54.27% in the second and third cycles, respectively. The absorption isotherm of chromium adsorption was also observed. The Cel-PEI material conformed to the Langmuir model with an R² value of 0.9997. The kinetics of chromium adsorption showed that under pseudo-second-order analysis, with R² values of 0.9909 and 0.9958 for Cel and Cel-PEI materials, respectively. The G° and H° values of the adsorption process were negative, indicating that the adsorption is spontaneous and that the adsorption process is exothermic. The efficient preparation adsorbent materials for Cr (VI) was achieved using a short microwave method that is low-cost and environmentally friendly for use in the treatment of Cr-contaminated wastewater.

A magnetic MIL-125-NH2@chitosan composite as a separable adsorbent for the removal of Cr(VI) from wastewater

Metal-organic frameworks (MOFs) are gradually used since of their huge specific surface area and superior pore structure. However, there are problems such as easy aggregation and difficult separation in water treatment. In this study, we prepared composite microspheres (FMCS-1) by modifying MIL-125-NH₂ with Fe₃O₄ and chitosan. The structural characterization and performance analysis of the materials showed that the introduction of chitosan effectively prevents the stacking of MOFs. The magnetic test manifested that Fe₃O₄ solved the problem of the difficult separation of MOFs from water. The removal potential of toxic Cr(VI) was tested by adsorption experiments. The isotherm model indicated that FMCS-1 is a single molecular layer adsorbent with a maximum adsorption capacity of 109.46 mg/g at pH = 2. The adsorption kinetics showed that the adsorption of Cr(VI) by FMCS-1 was chemical adsorption. The acid resistance test demonstrated that FMCS-1 can exist stably in acid solutions. The recycling experiments proved that the adsorbent can be reused and the removal percentage still reaches 50 % after 5 cycles. This work expands the application of MOFs in water treatment and also provides an effective adsorbent for Cr(VI) removal.

Study on adsorption of hexavalent chromium by composite material prepared from iron-based solid wastes

A new adsorbent with chromium removal function was synthesized by carbon thermal method using iron-containing waste Fenton sludge and carbon-containing solid waste fly ash to treat high pH scoring wastewater generated from industrial processes. The results showed that the adsorbent used T = 273.15 K, pH = 10, t = 1200 min, C₀ = 100 mg/L, had a removal rate of Cr(VI) of more than 80%, and the adsorption capacity could reach 393.79 mg/g. The characterization results show that the synthesized mesoporous nitrogen-doped composite material has a large specific surface area and mesoporous structure, and the surface of the material is rich in oxygen-containing functional groups and active sites. Compared with other studies, the adsorption capacity of the material is larger, which indicates that the removal effect of Cr(VI) in this study is better. The adsorption kinetic results show that the adsorption follows a pseudo second kinetic model, and the adsorption process is a chemisorption involving electron sharing or electron exchange. This experiment designed a simple method to synthesize mesoporous nitrogen-doped composites using industrial solid waste, with raw materials from cheap and easily available industrial solid waste, and solved the dual problems of heavy metals in wastewater and solid waste, providing a new idea for the resource utilization of Fenton sludge while not producing secondary pollution.

Preparation of Three-Dimensional MF/Ti3C2Tx/PmPD by Interfacial Polymerization for Efficient Hexavalent Chromium Removal

Heavy metal pollution is a serious threat to human health and the ecological environment, but adsorption technology based on nano adsorbents can effectively treat the crisis. However, due to the nanoscale effect, nano adsorbents have some crucial shortcomings, such as recycling difficulty and the loss of nanoparticles, which seriously limit their application. The feasible assembly of nano adsorbents is an accessible technology in urgent need of a breakthrough. In this study, three-dimensional (3D) adsorbent (MF/Ti₃C₂T_x/PmPD) with excellent performance and favorable recyclability was prepared by interfacial polymerization with melamine foam (MF) as the framework, two-dimensional (2D) titanium carbide (Ti₃C₂T_x) as the bridge and Poly (m-Phenylenediamine) (PmPD) as the active nano component. The morphology, structure, mechanical property of MF/Ti₃C₂T_x/PmPD and reference MF/PmPD were investigated through a scanning electron microscope (SEM), Fourier transformed infrared spectra (FT-IR), Raman scattering spectra and a pressure-stress test, respectively. Owning to the regulation of Ti₃C₂T_x on the morphology and structure of PmPD, MF/Ti₃C₂T_x/PmPD showed excellent adsorption capacity (352.15 mg/g) and favorable cycling performance. R-P and pseudo-second-order kinetics models could well describe the adsorption phenomenon, indicating that the adsorption process involved a composite process of single-layer and multi-layer adsorption and was dominated by chemical adsorption. In this research, the preparation mechanism of MF/Ti₃C₂T_x/PmPD and the adsorption process of Cr(VI) were systematically investigated, which provided a feasible approach for the feasible assembly and application of nano adsorbents in the environmental field.

Facile synthesis of sodium lignosulfonate/polyethyleneimine/sodium alginate beads with ultra-high adsorption capacity for Cr(VI) removal from water

Chromium (VI) is a widely occurring toxic heavy metal ion in industrial wastewater that seriously impacts the environment. In this study, we used environmentally friendly sodium lignosulfonate (SL), polyethyleneimine (PEI), and sodium alginate (SA) to synthesize SL/PEI/SA beads by employing a simple crosslinking method with to develop a novel absorbent with excellent adsorption capacity and practical application in wastewater treatment. We studied the adsorption performance of SL/PEI/SA through batch adsorption and continuous dynamic adsorption experiments. SL/PEI/SA has ultra-high adsorption capacity (2500 mg·g^-1) at 25 ℃, which is much higher than that of existing adsorbents. Humic acids and coexisting anions commonly found in wastewater have minimal effect on the adsorption performance of SL/PEI/SA. In the column system, 1 g SL/PEI/SA can treat 8.1 L secondary electroplating wastewater at a flow rate of 0.5 mLmin^-1, thereby enabling the concentration of Cr(VI) in secondary electroplating wastewater to meet the discharge standard (< 0.2 mg·L^-1). It is worth noting that the concentration of competitive ions in secondary electroplating wastewater is more than 500 times higher than that of Cr(VI). These results demonstrate that the novel SL/PEI/SA beads can be effectively applied in the removal of Cr(VI) in wastewater.

Chitosan as a Tool for Sustainable Development: A Mini Review

New developments require innovative ecofriendly materials defined by their biocompatibility, biodegradability, and versatility. For that reason, the scientific society is focused on biopolymers such as chitosan, which is the second most abundant in the world after cellulose. These new materials should show good properties in terms of sustainability, circularity, and energy consumption during industrial applications. The idea is to replace traditional raw materials with new ecofriendly materials which contribute to keeping a high production rate but also reducing its environmental impact and the costs. The chitosan shows interesting and unique properties, thus it can be used for different purposes which contributes to the design and development of sustainable novel materials. This helps in promoting sustainability through the use of chitosan and diverse materials based on it. For example, it is a good sustainable alternative for food packaging or it can be used for sustainable agriculture. The chitosan can also reduce the pollution of other industrial processes such as paper production. This mini review collects some of the most important advances for the sustainable use of chitosan for promoting circular economy. Hence, the present review focuses on different aspects of chitosan from its synthesis to multiple applications.