Facile fabrication of three-dimensional nanofibrous foams of cellulose@g-C3N4@Cu2O with superior visible-light photocatalytic performance

Enhancing the Separation Performance of Cellulose Membranes Fabricated from 1-Ethyl-3-methylimidazolium Acetate by Introducing Acetone as a Co-Solvent

Cellulose, a sustainable raw material, holds great promise as an ideal candidate for membrane materials. In this work, we focused on establishing a low-cost route for producing cellulose microfiltration membranes by adopting a co-solvent system comprising the ionic liquid 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc) and acetone. The introduction of acetone as a co-solvent into the casting solution allowed control over the viscosity, thereby significantly enhancing the morphologies and filtration performances of the resulting cellulose membranes. Indeed, applying this co-solvent allowed the water permeability to be significantly increased, while maintaining high rejections. Furthermore, the prepared cellulose membrane demonstrated excellent fouling resistance behavior and flux recovery behavior during a challenging oil-in-water emulsion filtration. These results highlight a promising approach to fabricate high-performance cellulose membranes.

Optimization of methyl orange decolorization by bismuth(0)-doped hydroxyapatite/reduced graphene oxide composite using RSM-CCD

In the current study, the catalyst for the decolorization of methyl orange (MO) was developed HAp-rGO by the aqueous precipitation approach. Then, bismuth(0) nanoparticles (Bi NPs), which expect to show high activity, were reduced on the surface of the support material (HAp-rGO). The obtained catalyst was characterized by scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDX), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques. The parameters that remarkably affect the decolorization process (such as time, initial dye concentration, NaBH4 amount, and catalyst amount) have been examined by response surface methodology (RSM), an optimization method that has acquired increasing significance in recent years. In the decolorization of MO, the optimum conditions were identified as 2.91 min, Co: 18.85 mg/L, NaBH4 amount: 18.35 mM, and Bi/HAp-rGO dosage: 2.12 mg/mL with MO decolorization efficiency of 99.60%. The decolorization process of MO with Bi/HAp-rGO was examined in detail kinetically and thermodynamically. Additionally, the possible decolorization mechanism was clarified. The present work provides a new insight into the use of the optimization process for both the effective usage of Bi/HAp-rGO and the catalytic reduction of dyes.

Facile fabrication of 3D Janus foams of electrospun cellulose nanofibers/rGO for high efficiency solar interface evaporation

Solar-powered interfacial evaporation is one of the most efficient state-of-the-art technologies for producing clean water via desalination. Herein, we report a novel bio-based nanofibrous foam for high efficiency solar interface evaporation. To this end, a hybrid membrane of cellulose nanofibers/graphene oxide (GO) is first fabricated by electrospinning coupled with in situ layer-by-layer self-assembly technique. After that, the membrane is subjected to a foaming process in an aqueous NaBH4, which effectively transforms the 2D membrane into a 3D foam. This structure can improve the photothermal conversion efficiency and also facilitate the water transport at the gas-water interface. In the meantime, the GO is converted to the reduced GO (rGO) with a higher light absorption efficiency. Finally, one side of the foam is hydrophobically modified via spray-coating with a fluorocarbon resin (FR) to obtain the Janus type 3D foam, namely FR@EC/rGO. The resultant 3D foam combines the functions of solar energy absorption in the upper layer and water pumping capability in the lower layer. It exhibits an extraordinary solar vapor conversion efficiency of 94.2 % and a fast evaporation rate of 1.83 kg m-2 h-1, showing high potential in future seawater desalination.

In Situ Polycondensation Synthesis of NiS-g-C3N4 Nanocomposites for Catalytic Hydrogen Generation from NaBH4

The nanocomposites of S@g-C₃N₄ and NiS-g-C₃N₄ were synthesized for catalytic hydrogen production from the methanolysis of sodium borohydride (NaBH₄). Several experimental methods were applied to characterize these nanocomposites such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and environmental scanning electron microscopy (ESEM). The calculation of NiS crystallites revealed an average size of 8.0 nm. The ESEM and TEM images of S@g-C₃N₄ showed a 2D sheet structure and NiS-g-C₃N₄ nanocomposites showed the sheet materials that were broken up during the growth process, revealing more edge sites. The surface areas were 40, 50, 62, and 90 m²/g for S@g-C₃N₄, 0.5 wt.% NiS, 1.0 wt.% NiS, and 1.5 wt.% NiS, respectively. The pore volume of S@g-C₃N₄ was 0.18 cm³, which was reduced to 0.11 cm³ in 1.5 wt.% NiS owing to the incorporation of NiS particles into the nanosheet. We found that the in situ polycondensation preparation of S@g-C₃N₄ and NiS-g-C₃N₄ nanocomposites increased the porosity of the composites. The average values of the optical energy gap for S@g-C₃N₄ were 2.60 eV and decreased to 2.50, 2.40, and 2.30 eV as the NiS concentration increased from 0.5 to 1.5 wt.%. All NiS-g-C₃N₄ nanocomposite catalysts had an emission band that was visible in the 410-540 nm range and the intensity of this peak decreased as the NiS concentration increased from 0.5 to 1.5 wt.%. The hydrogen generation rates increased with increasing content of NiS nanosheet. Moreover, the sample 1.5 wt.% NiS showed the highest production rate of 8654 mL/g·min due to the homogeneous surface organization.