Studies on the rheological properties of amphiphilic nanosilica and a partially hydrolyzed polyacrylamide hybrid for enhanced oil recovery

Development of Novel Silicon Quantum Dots and Their Potential in Improving the Enhanced Oil Recovery of HPAM

Hydrolyzed polyacrylamide (HPAM) is commonly used in polymer flooding, however, it is prone to viscosity reduction at high temperatures and high salinities, weakening its ability to improve oil recovery. In this work, sulfonated modified silicon quantum dots (S-SiQDs) were synthesized and then added to HPAM to study the improvement of rheological properties and enhanced oil recovery performance of HPAM at high temperatures and salinities. It is found that the S-SiQDs with a concentration of only 0.1 wt % can significantly increase the viscosity of HPAM from 28.5 to 39.6 mPa·s at 60 °C and 10,000 mg/L NaCl. Meanwhile, the HPAM/S-SiQDs hybrid solution always possessed higher viscosity and viscoelastic moduli than HPAM, attributed to the hydrogen bonding between HPAM and S-SiQDs. Notably, HPAM/S-SiQDs still maintained elastic behavior at harsh conditions, indicating that they formed a strong network structure. Through oil displacement experiments, it was found that the oil recovery of HPAM/S-SiQDs was higher (28.3%), while that of HPAM was only 17.2%. Thereafter, the utilization sequence of oil during the displacement process was studied with nuclear magnetic resonance experiments. Ultimately, the oil displacement mechanism of HPAM/S-SiQDs was deeply analyzed, including viscosity thickening and wetting reversal.

Functional Gels and Chemicals Used in Oil and Gas Drilling Engineering: A Status and Prospective

Research into functional gels and chemicals and their applications represents a cutting-edge international field of study. For example, investigating how they can be applied in oil and gas drilling (and extraction engineering) and developing novel functional chemical materials for the oil field could provide innovative solutions and technological methods for oil and gas drilling and extraction operations. Through a literature analysis, this paper presents a review of the current research status and application scenarios of different types of functional gels and chemicals, both domestically and internationally. The classification and preparation principles of various functional materials are systematically outlined and the current applications of functional gels and chemicals in oil and gas drilling and extraction engineering are introduced. These applications include drilling and plugging, enhanced oil recovery, water plugging, and profile control. The formation mechanisms and application scenarios of different types of gels and chemicals are also analyzed and summarized, with a discussion of their prospects in oil and gas drilling and extraction engineering. We broaden the scope of functional gels and chemicals by exploring new application fields and promoting the development of different types of gels and chemicals in a more intelligent direction.

Mechanism and Performance Analysis of Nanoparticle-Polymer Fluid for Enhanced Oil Recovery: A Review

With the increasing energy demand, oil is still an important fuel source worldwide. The chemical flooding process is used in petroleum engineering to increase the recovery of residual oil. As a promising enhanced oil-recovery technology, polymer flooding still faces some challenges in achieving this goal. The stability of a polymer solution is easily affected by the harsh reservoir conditions of high temperature and high salt, and the influence of the external environment such as high salinity, high valence cations, pH value, temperature and its own structure is highlighted. This article also involves the introduction of commonly used nanoparticles, whose unique properties are used to improve the performance of polymers under harsh conditions. The mechanism of nanoparticle improvement on polymer properties is discussed, that is, how the interaction between them improves the viscosity, shear stability, heat-resistance and salt-tolerant performance of the polymer. Nanoparticle-polymer fluids exhibit properties that they cannot exhibit by themselves. The positive effects of nanoparticle-polymer fluids on reducing interfacial tension and improving the wettability of reservoir rock in tertiary oil recovery are introduced, and the stability of nanoparticle-polymer fluid is described. While analyzing and evaluating the research on nanoparticle-polymer fluid, indicating the obstacles and challenges that still exist at this stage, future research work on nanoparticle-polymer fluid is proposed.

12012 fundamental mechanisms behind nanotechnology applications in oil and gas: Emerging nano-EOR processes

As the important role of enhanced oil recovery (EOR) in meeting the world’s energy requirement is growing, use of nanoparticles in lieu of, or in combination with, the existing EOR agents to expand EOR’s applicable range is receiving significant attention. Two of the most actively investigated applications are: 1) wettability alteration by addition of nanoparticles into the waterflood injection water, and 2) use of nanoparticle-stabilized Pickering foams and emulsions mainly for EOR process mobility control. As comprehensive reviews are recently available on these topics, two other emerging nanoparticle applications are critically reviewed here: 1) nanoparticle addition for enhanced polymer flooding, and 2) use of magnetic nanoparticles for oil displacement control. Three and five proposed mechanisms of these two applications are critically reviewed, respectively. The most recent progresses are covered, and the challenges and possible future works are discussed.

Application of Polymers for Chemical Enhanced Oil Recovery: A Review

Polymers play a significant role in enhanced oil recovery (EOR) due to their viscoelastic properties and macromolecular structure. Herein, the mechanisms of the application of polymeric materials for enhanced oil recovery are elucidated. Subsequently, the polymer types used for EOR, namely synthetic polymers and natural polymers (biopolymers), and their properties are discussed. Moreover, the numerous applications for EOR such as polymer flooding, polymer foam flooding, alkali–polymer flooding, surfactant–polymer flooding, alkali–surfactant–polymer flooding, and polymeric nanofluid flooding are appraised and evaluated. Most of the polymers exhibit pseudoplastic behavior in the presence of shear forces. The biopolymers exhibit better salt tolerance and thermal stability but are susceptible to plugging and biodegradation. As for associative synthetic polyacrylamide, several complexities are involved in unlocking its full potential. Hence, hydrolyzed polyacrylamide remains the most coveted polymer for field application of polymer floods. Finally, alkali–surfactant–polymer flooding shows good efficiency at pilot and field scales, while a recently devised polymeric nanofluid shows good potential for field application of polymer flooding for EOR.

Morphological and Structural Properties of Amino-Functionalized Fumed Nanosilica and Its Comparison with Nanoparticles Obtained by Modified Stöber Method

In industry, silica nanoparticles (NPs) are obtained by the fuming and the precipitation method. Fumed silica NPs are commonly used in the preparation of nanocomposites because they have an extremely low bulk density (160-190 kg/m3), large surface area (50-600 m2/g), and nonporous surface, which promotes strong physical contact between the NPs and the organic phase. Fumed silica has fewer silanol groups (Si-OH) on its surface than the silica prepared by the Stöber method. However, the number of -OH groups on the fumed silica surface can be increased by pretreating them with sodium hydroxide (NaOH) before further surface modification. In this study, the effectiveness of the NaOH pretreatment was evaluated on commercial fumed silica NPs with a surface area of 200 m2/g. The number of surface -OH groups was estimated by potentiometric titration. The pretreated fumed NPs, and the precipitated NPs (prepared by the Stöber method) were modified with 3-aminopropyltriethoxysilane (APTES) to obtain A200S and nSiO2-APTES, respectively. The NPs were characterized using electron dispersive scanning (EDS), scanning electron microscopy (SEM), dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), BET (Brunauer-Emmett-Teller) analysis, and ζ-potential. XRD confirmed the presence of the organo-functional group on the surface of both NPs. After the amino-functionalization, the ζ-potential values of the nSiO2 and A200 changed from -35.5 mV and -14.4 mV to +26.2 mV and +11.76 mV, respectively. Consequently, we have successfully synthesized functionalized NPs with interesting, specific surface area and porosity (pore volume and size), which can be attractive materials for chemical and energy industries.

Comparison of an Emulsion- and Solution-Prepared Acrylamide/AMPS Copolymer for a Fluid Loss Agent in Drilling Fluid

Acrylamide polymers were widely used as oilfield chemical treatment agents because of their wide viscosity range and versatile functions. However, with the increased formation complexity, their shortcomings such as poor solubility and low resistance to temperature, salt, and calcium were gradually exposed. In this paper, acrylamide (AM)/2-acrylamide-2-methyl-1-propane sulfonic acid (AMPS) copolymers were synthesized by aqueous solution polymerization and inverse emulsion polymerization, respectively. The aqueous polymer (W-AM/AMPS) and the inverse emulsion polymer (E-AM/AMPS) were characterized by Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (¹H NMR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and particle size analysis. The rheological properties, filtration properties, and sodium ion (Na⁺) and calcium ion (Ca²⁺) resistance were investigated. The results showed that E-AM/AMPS not only had a dissolution speed 4 times faster than that of W-AM/AMPS but also had superior shear-thinning performance both before and after aging. The filtration property of the bentonite system containing 2 wt % E-AM/AMPS was also better than that of the bentonite system containing 2 wt % W-AM/AMPS. In addition, E-AM/AMPS also exhibited extremely high tolerance for Na⁺ and Ca²⁺. The huge difference between rheological and filtration properties of E-AM/AMPS and W-AM/AMPS in drilling fluid can be attributed to the differences in the polymer microstructure caused by the two polymerization methods. Both FTIR and ¹H NMR results showed that more hydrogen bonds were formed between E-AM/AMPS molecular groups and molecular chains, which led to a cross-linked network structure of E-AM/AMPS which was observed by TEM. It was this cross-linked network structure that made E-AM/AMPS have a high viscosity and allowed it to be better adsorbed on bentonite particles, thus exhibiting excellent rheological and filtration behavior. In addition, E-AM/AMPS powder had a high specific surface area so that it can be dissolved in water faster, greatly reducing the time and difficulty of configuring drilling fluid.

Preparation and properties of amphiphilic hydrophobically associative polymer/ montmorillonite nanocomposites

In this research, a novel amphiphilic hydrophobically associative polymer nanocomposite (ADOS/OMMT) was prepared using acrylamide (AM), sodium 4-vinylbenzenesulfonate (SSS), N, N'-dimethyl octadeyl allyl ammonium bromide (DOAAB) and organo-modified montmorillonite (OMMT) through in situ polymerization. Both X-ray diffraction patterns and transmission electron microscopy images verified the dispersion morphology of OMMT in the copolymer matrix. Then, the effect of the introduction of OMMT layers on the copolymer properties was studied by comparing with pure copolymer AM/SSS/DOAAB (ADOS). The thermal degradation results demonstrated that the thermal stability of the ADOS/OMMT were better than pure copolymer ADOS. During the solution properties tests, ADOS/OMMT nanocomposite was superior to ADOS in viscosifying ability, temperature resistance, salt tolerance, shear resistance and viscoelasticity, which was because OMMT contributed to enhance the hydrophobic association structure formed between polymer molecules. Additionally, the ADOS/OMMT nanocomposite exhibited more excellent interfacial activity and crude oil emulsifiability in comparison to pure copolymer ADOS. These performances indicated ADOS/OMMT nanocomposite had good application prospects in tertiary recovery.

Study on the Reducing Injection Pressure Regulation of Hydrophobic Carbon Nanoparticles

The interest in the application of nanofluid in reducing injection pressure has been increasing especially for tight reservoirs. In this work, a new type of hydrophobic carbon nanofluid was prepared and the pressure-reducing performance was investigated. The results of particle size distribution, zeta potential, and transmission electron microscopy image showed that the dispersion of nanofluid was uniform and stable. In addition, the hydrophobic carbon nanofluid showed excellent antitemperature and antisalinity property. The contact angle of oil-wet glass slide can range from 45 to 89° after it adsorbs hydrophobic carbon nanoparticles (HCNPs). The atomic force microscope tests showed that the core surface roughness was reduced about 16.67%. The core flooding tests showed that the pressure-reducing rate of 0.15 wt % HCNP nanofluid can reach 17.00%. HCNPs show good performance in reducing pressure and have a broad application prospect in oil field development.

pH-Switchable IFT variations and emulsions based on the dynamic noncovalent surfactant/salt assembly at the water/oil interface

Additional HCl can facilely control the dynamic noncovalent interaction between anionic surfactant sodium dodecyl benzene sulfonate (SDBS) and additional organic matter, 4,4'-oxydianiline (ODA), at the water/oil interface. At low HCl concentration (ODA/HCl molar ratio (r) = 1 : 1.5, [ODA] = 250 mg L-1), the ODA+ ions effectively enhanced the SDBS ability to reduce the water/oil interfacial tension (IFT) by about two orders of magnitude, while the (SDBS)2/ODA2+ gemini-like surfactants could be constructed at a relatively high HCl concentration (r = 1 : 4, [ODA] = 250 mg L-1), which could largely reduce the IFT to 1.19 × 10-3 mN m-1. Molecular simulation was employed to explore the interfacial activity of ODAn+ (ODA+/ODA2+) ions and the SDBS/ODAn+ interaction. The control experiments used another three surfactants to verify the proposed model. The pH-switchable gradual protonation of amino groups in ODA molecules determined the SDBS/ODA interfacial assembly, which was responsible for the reversal of IFT variations and the related emulsion behaviors.