Microbial-electrochemical bioremediation and detoxification of dibenzothiophene-polluted soil

Pilot-scale field studies on activated microbial remediation of petroleum-contaminated soil

Soil contamination by petroleum, including crude oil from various sources, is increasingly becoming a pressing global environmental concern, necessitating the exploration of innovative and sustainable remediation strategies. The present field-scale study developed a simple, cost-effective microbial remediation process for treating petroleum-contaminated soil. The soil treatment involves adding microbial activators to stimulate indigenous petroleum-degrading microorganisms, thereby enhancing the total petroleum hydrocarbons (TPH) degradation rate. The formulated microbial activator provided a growth-enhancing complex of nitrogen and phosphorus, trace elements, growth factors, biosurfactants, and soil pH regulators. The field trials, involving two 500 m3 soil samples with the initial TPH content of 5.01% and 2.15%, were reduced to 0.41% and 0.02% in 50 days, respectively, reaching the national standard for cultivated land category II. The treatment period was notably shorter than the commonly used composting and bioaugmentation methods (typically from 8 to 12 weeks). The results indicated that the activator could stimulate the functional microorganisms in the soil and reduce the phytotoxicity of the contaminated soil. After 40 days of treatment, the germination rate of rye seeds increased from 20 to 90%, indicating that the microbial activator could be effectively used for rapid on-site remediation of oil-contaminated soils.

Passive electrobioremediation approaches for enhancing hydrocarbons biodegradation in contaminated soils

Electrobioremediation technologies hold considerable potential for the treatment of soils contaminated by petroleum hydrocarbons (PH), since they allow stimulating biodegradation processes with no need for subsurface chemicals injection and with little to no energy consumption. Here, a microbial electrochemical snorkel (MES) was applied for the treatment of a soil contaminated by hydrocarbons. The MES consists of direct coupling of a microbial anode with a cathode, being a single conductive, non-polarized material positioned suitably to create an electrochemical connection between the anoxic zone (the contaminated soil) and the oxic zone (the overlying oxygenated water). Soil was also supplemented with electrically conductive particles of biochar as a strategy to construct a conductive network with microbes in the soil matrix, thus extending the radius of influence of the snorkel. The results of a comprehensive suite of chemical, microbiological and ecotoxicological analyses evidenced that biochar addition, rather than the presence of a snorkel, was the determining factor in accelerating PH removal from contaminated soils, possibly accelerating syntrophic and/or cooperative metabolisms involved in the degradation of PH. The enhancement of biodegradation was mirrored by an increased abundance of anaerobic and aerobic microorganisms known to be involved in the degradation of PH and related functional genes. Plant ecotoxicity assays confirmed a reduction of soils toxicity in treatments receiving electrically conductive biochar.

Review on microbial fuel cells applications, developments and costs

The microbial fuel cell (MFC) technology has attracted significant attention in the last years due to its potential to recover energy in a wastewater treatment. The idea of using an MFC in industry is very attractive as the organic wastes can be converted into energy, reducing the waste disposal costs and the energy needs while increasing the company profit. However, taking aside these promising prospects, the attempts to apply MFCs in large-scale have not been succeeded so far since their lower performance and high costs remains challenging. This review intends to present the main applications of the MFC systems and its developments, particularly the advances on configuration and operating conditions. The diagnostic techniques used to evaluate the MFC performance as well as the different modeling approaches are described. Towards the introduction of the MFC in the market, a cost analysis is also included. The development of low-cost materials and more efficient systems, with high higher power outputs and durability, are crucial towards the application of MFCs in industrial/large scale. This work is a helpful tool for discovering new operation and design regimes.

A visible-light-responsive molecularly imprinted polyurethane for specific detection of dibenzothiophene in gasoline

Dibenzothiophene and its derivatives in gasoline and diesel would release sulfur oxides during combustion, and this is harmful to human health and the environment. This paper reports a method based on a visible-light-responsive molecularly imprinted polyurethane (VMIPU) to monitor trace dibenzothiophene in gasoline. The VMIPU was prepared by a polyaddition reaction using N,N-bis-(2-hydroxyethyl)-4-phenylazoaniline as the functional monomer, dibenzothiophene as the template molecule, diphenylmethane diisocyanate as the crosslinker and castor oil as the chain extender. The VMIPU showed good visible-light-response and specific adsorption for dibenzothiophene. The trans → cis photoisomerization rate constant of azobenzene chromophores in the VMIPU shows a linear relationship with the dibenzothiophene concentration in the range of 0-20 μmol L^-1. This was used to estimate trace dibenzothiophene in spiked gasoline with recoveries of 95.7-101.0% and relative standard deviations of 7.0-12.7%.

Microbial approaches for remediation of pollutants: Innovations, future outlook, and challenges

Environmental contamination with persistent organic pollutants has emerged as a serious threat of pollution. Bioremediation is a key to eliminate these harmful pollutants from the environment and has gained the interest of researchers during the past few decades. Scientific knowledge upon microbial interactions with individual pollutants over the past decades has helped to abate environmental pollution. Traditional bioremediation approaches have limitations for their applications; hence, it is essential to discover new bioremediation approaches with biotechnological interventions for best results. The developments in various methodologies are expected to increase the efficiency of bioremediation techniques and provide environmentally sound strategies. This paper deals with the profiling of microorganisms present in polluted sites using various techniques such as culture-based approaches and omics-based approaches. Besides this, it also provides up-to-date scientific literature on the microbial electrochemical technologies which are nowadays considered as the best approach for remediation of pollutants. Detailed information about future outlook and challenges to evaluate the effect of various treatment technologies for remediation of pollutants has been discussed.

Recent advances in soil microbial fuel cells for soil contaminants remediation

The cost-effective and eco-friendly approaches are needed for decontamination of polluted soils. The bio-electrochemical system, especially microbial fuel cells (MFCs) offer great promise as a technology for remediation of soil, sediment, sludge and wastewater. Recently, soil MFCs (SMFCs) have been attracting increasing amounts of interest in environmental remediation, since they are capable of providing a clean and inexhaustible source of electron donors or acceptors and can be easily controlled by adjusting the electrochemical parameters. In this review, we comprehensively covered the principle of SMFCs including the mechanisms of electron releasing and electron transportation, summarized the applications for soil contaminants remediation by SMFCs with highlights on organic contaminants degradation and heavy metal ions removal. In addition, the main factors that affected the performance of SMFCs were discussed in details which would be helpful for performance optimization of SMFCs as well as the efficiency improvement for soil remediation. Moreover, the key issues need to be addressed and future perspectives are presented.

A Novel Design Portable Plugged-Type Soil Microbial Fuel Cell for Bioelectricity Generation

Soil microbial fuel cells (SMFCs) are a promising cost-effective power source for on-demand electricity generation applications. So far, reported SMFC configurations are usually bulky and hard to setup. In this study, a low-cost portable plugged-type SMFC (PSMFC) was designed and fabricated for on-demand micropower generation. The PSMFC can be activated just by plugging into natural wet soil, which is easy to access in the natural condition. The PSMFC uses carbon-based electrodes for cost-effectiveness. After setting the PSMFC into the soil to activate, it started to produce electricity after 1 h and reached the power density of 7.3 mW/m2 after 48 h. The proposed PSMFC can potentially generate electricity for remote sensors or soil sensing systems.

Bioremediation of oily sludge by solid complex bacterial agent with a combined two-step process

In the present research, a bioremediation process was developed using solid complex bacterial agents (SCBA) through a combined two-step biodegradation process. Four isolated strains showed high efficiency for the degradation of total petroleum hydrocarbons (TPH) and the reduction of COD of the oily sludge, at 96.6% and 92.6%, respectively. The mixed strains together with bran prepared in form of SCBA exhibited improved performance compared to individual strains, all of which had an optimal temperature of around 35 °C. The use of SCBA provided advantages over commonly used liquid media for storage and transportation. The two-step process, consisting of firstly biosurfactant-assisted oil recovery and secondly biodegradation of the remaining TPH with SCBA, demonstrated the capability for treating oily sludge with high TPH content (>10 wt%) and short process period (60 days). The large-scale (5 tons oily sludge) field test, achieving a TPH removal efficiency of 93.8% and COD reduction of 91.5%, respectively, confirmed the feasibility and superiority of the technology for industrial applications.

Biochar enhances bioelectrochemical remediation of pentachlorophenol-contaminated soils via long-distance electron transfer

The soil bioelectrochemical system (SBES) is a promising biotechnology for the remediation of contaminated soils. However, the effective distance of pollutant removal in the SBES was usually limited in a few centimeters near the electrode surface. In this study, we used biochar as the model conductor to construct a conductive network with microbes in the soil matrix to extend the effective distance of pollutant removal in the SBES. Pentachlorophenol (PCP) was used as the representative contaminant to probe long-distance electron transfer facilitated by the networks. The removal of PCP and microbial community analyses at different distances toward the electrode were monitored. The results showed that PCP transformation in the SBES without biochar amendment mainly occurred within 4 cm around the electrode. However, the effective distance of ∼ 16 cm toward the electrode could be achieved for efficient PCP degradation in the SBES amended with highly conductive biochar. Microbial community analysis confirmed the establishment of bacteria-biochar networks, where Desulfitobacterium and Geobacter were enriched and spatially distributed in the biochar-amended SBES. The results demonstrate that long-distance electron transfer can be achieved in the biochar-amended soil matrix, and shed light on the development of bioelectrochemical strategy for efficient organic pollutant degradation in soils.

Isolation and characterization of novel bacterial strains for integrated solar-bioelectrokinetic of soil contaminated with heavy petroleum hydrocarbons

This study investigated the isolation and characterization of three novel bacterial strains; Acinetobacter calcoaceticus, Sphingobacterium multivorum, and Sinorhizobium, isolated form agriculture land. From three hundred strains of bacteria, the three isolates were identified for their superior diesel degradation ability by a series of bench-scale tests. The isolates were further investigated in bench tests for their ability to grow in different diesel fuel concentrations, temperature and pH; degrade diesel fuel in vitro; and for the identification of functional genes. Semi-pilot bioelectrokinetic tests were conducted in three electrokinetic cells. An innovative electrode configuration was adopted to stabilize the soil pH and water content during the test. The genes expressed in the diesel degradation process including Lipases enzymes Lip A, LipB, Alk-b2, rubA, P450, and 1698/2041 were detected in the three isolates. The results showed that the solar panel voltage output is in agreement with the trapezoid model. The temperatures in the cells were found to be 5-7 °C higher than the ambient temperature. The electrode configuration succeeded in stabilizing the soil pH and water content, preventing the development of a pH gradient, important progress for the survival of bacteria. The diesel degradation in the soil after bioelectrokinetic tests were 20-30%, compared to 10-12% in the controls. The study succeeded in developing environmentally friendly technology employing novel bacterial strains to degrade diesel fuel and utilizing solar panels to produce renewable energy for bioelectrokinetics during the winter season.

Electrodes boost microbial metabolism to mineralize antibiotics in manure

Livestock manures are potential sources of antibiotics in the environment. Sulfamethazine (SMZ), frequently used in veterinary medicine, can enter the environment by using manure as soil fertilizer due to its incomplete absorption in the animal gut and its unmetabolized excretion. The objective of this study was to evaluate the mineralization of ¹⁴C-labelled SMZ in manure under a new redox scenario provided by microbial electrochemical reactors, termed microbial electroremediating cells (MERC). These devices aim to overcome the electron acceptor limitation in bacterial oxidative metabolism by means of using electrodes to enhance the biodegradation of pollutants in the environment. Our results revealed that the total degradation of ¹⁴C-SMZ reached 43.5% in short term batch laboratory scale experiments under reducing conditions (-400 mV vs. Ag/AgCl). Actually, SMZ mineralization was enhanced up to 10-fold in the early stages (after 2 weeks) in comparison with an electrode-free natural attenuation assay. Moreover, mineralization showed a dependence on electrode potential, with negligible results for conditions set to +400 mV vs Ag/AgCl. The impact of merging electrodes and microorganisms for manure bioremediation suggests a promising future for this emerging technology to treat polluted livestock wastes and prevent soil and groundwater pollution.

Recent advances in microbial electrochemical system for soil bioremediation

Soil contamination poses a serious threat to ecosystem and human well-being. Compared to conventional physical and chemical treatment, the microbial electrochemical system (MES) offers a sustainable and environment-friendly solution for soil bioremediation. In principle, soil microbe degrades organic substrate and releases electron in anode region. The electron flows through electric circuit to the cathode and finally is accepted by oxygen or oxidized metals. With various inherent advantages, MES has been applied in petroleum hydrocarbon, chlorinated organics and heavy metals bioremediation in soils. This paper aims to review the recent advances of MES in soil bioremediation, including main mechanisms of contaminant removal with MES, configurations of soil MES and current development in bioremediation of soil contaminated by organic and inorganic pollutants. Moreover, challenges and future prospects of soil MES are discussed.

Optimization of combined in-vessel composting process and chemical oxidation for remediation of bottom sludge of crude oil storage tanks

In this research, removal of petroleum hydrocarbons from oily sludge of crude oil storage tanks was investigated under the optimized conditions of in-vessel composting process and chemical oxidation with H₂O₂ and Fenton. After determining the optimum conditions, the sludge was pre-treated with the optimum state of the oxidation process. Then, the determined optimum ratios of the sludge to immature compost were composted at a C:N:P ratio of 100:5:1 and moisture content of 55% for a period of 10 weeks. Finally, both pre-treated and composted mixtures were again oxidized with the optimum conditions of the oxidants. Results showed that total petroleum hydrocarbons (TPH) removal of the 1:8 and 1:10 composting reactors which were pre-treated with H₂O₂ were 88.34% and 90.4%, respectively. In addition, reduction of TPH in 1:8 and 1:10 composting reactors which were pre-treated with Fenton were 83.90% and 84.40%, respectively. Without applying the pre-treatment step, the composting reactors had a removal rate of about 80%. Therefore, pre-treatment of the reactors increased the TPH removal. However, post-oxidation of both pre-treated and composted mixtures reduced only 13-16% of TPH. Based on the results, remarkable overall removal of TPH (about 99%) was achieved by using chemical oxidation and subsequent composting process. The study showed that chemical oxidation with H₂O₂ followed by in-vessel composting is a viable choice for the remediation of the sludge.

Induced bioelectrochemical metabolism for bioremediation of petroleum refinery wastewater: Optimization of applied potential and flow of wastewater

Hybrid based bioelectrochemical system (BES) configured with embedded anode and cathode electrodes in soil was tested for the bioelectrochemical degradation of petroleum refinery wastewater (PRW). Four applied potentials were studied to optimize under batch mode operation, among which 2 V resulted in higher COD degradation (69.2%) and power density (725 mW/m²) during 7 days of operation. Further studies with continuous mode of operation at optimized potential (2 V) showed that hydraulic retention time (HRT) of 19 h achieved the highest COD removal (37%) and highest power density (561 mW/m²). BES function with respect to treatment efficiencies of other pollutants of PRW was also identified with respect to oil and grease (batch mode, 91%; continuous mode, 34%), total dissolved salts (batch mode, 53%; continuous mode, 24%) and sulfates (batch mode, 59%; continuous mode, 42%). Soil microenvironment in association with BES forms complex processes, providing suitable conditions for efficient treatment of PRW.

Surfactants selectively reallocated the bacterial distribution in soil bioelectrochemical remediation of petroleum hydrocarbons

Soil contaminated by aged petroleum hydrocarbons is faced with scarcity of electron acceptors, low activity of functional microbes and inefficient electron transfer, which hinder the bioremediation application. The soil microbial fuel cell (MFC) simultaneously solves these problems with bioelectricity production. In this study, five types of surfactants were introduced to enhance the bioavailability of aged petroleum hydrocarbon in soils. The ampholytic surfactant (lecithos) was optimal due to the highest bioelectricity generation (0.321Cd^-1g^-1) and promoted hydrocarbon degradation (328%), while the nonionic (glyceryl monostearate) and cationic (cetyltrimethylammonium bromide) surfactants were inefficient. The surfactants induced a special microbial enrichment affiliated with Proteobacteria, Firmicutes, Bacteroidetes, Actinobacteria, Chloroflexi, Planctomycetes and Acidobacteria (93%-99% of total) in soil MFCs. The anionic surfactant (sodium dodecyl sulfate) exhibited the strongest selectivity, and α-proteobacteria and γ-proteobacteria abundances decreased while Clostridia increased, much like the result obtained with the biosurfactant β-cyclodextrin. Furthermore, Bacillus abundance was increased in connected soil MFCs, except addition of lecithos in which Clostridium increased to 14.88% from 3.61% in the control. The high correlations among Bacillus, Phenylobacterium, Solibacillus (0.9162-0.9577) and among Alcaligenes, Dysgonomonas, Sedimentibacter (0.9538-0.9966) indicated a metabolic network of microorganisms in the soil bioelectrochemical remediation system.

Silica immobilization of Geobacter sulfurreducens for constructing ready-to-use artificial bioelectrodes

Microbial electrochemical technologies (METs) rely on the control of interactions between microorganisms and electronic devices, enabling to transform chemical energy into electricity. We report a new approach to construct ready-to-use artificial bioelectrodes by immobilizing Geobacter sulfurreducens cells in composite materials associating silica gel and carbon felt fibres. Viability test confirmed that the majority of bacteria (ca. 70 ± 5%) survived the encapsulation process in silica and that cell density did not increase in 96 h. The double entrapment within the silica-carbon composite prevented bacterial release from the electrode but allowed a suitable mass transport (ca. 5 min after electron donor pulse), making the electrochemical characterization of the system possible. The artificial bioelectrodes were evaluated in three-electrode reactors and the maximum current displayed was ca. 220 and 150 μA cm-3 using acetate and lactate as electron donors respectively. Cyclic voltammetry of acetate-fed bioelectrodes revealed a sigmoidal catalytic oxidation wave, typical of more advanced-stage biofilms. The presence of G. sulfurreducens within composites was ascertained by SEM analysis, suggesting that only part of the bacterial population was in direct contact with the carbon fibres. Preliminary analyses of the transcriptomic response of immobilized G. sulfurreducens enlightened that encapsulation mainly induces an osmotic stress to the cells. Therefore, ready-to-use artificial bioelectrodes represent a versatile time- and cost-saving strategy for microbial electrochemical systems.

Opportunities for groundwater microbial electro-remediation

Groundwater pollution is a serious worldwide concern. Aromatic compounds, chlorinated hydrocarbons, metals and nutrients among others can be widely found in different aquifers all over the world. However, there is a lack of sustainable technologies able to treat these kinds of compounds. Microbial electro‐remediation, by the means of microbial electrochemical technologies (MET), can become a promising alternative in the near future. MET can be applied for groundwater treatment in situ or ex situ, as well as for monitoring the chemical state or the microbiological activity. This document reviews the current knowledge achieved on microbial electro‐remediation of groundwater and its applications.

Metabolic and process engineering for biodesulfurization in Gram-negative bacteria

Microbial desulfurization or biodesulfurization (BDS) is an attractive low-cost and environmentally friendly complementary technology to the hydrotreating chemical process based on the potential of certain bacteria to specifically remove sulfur from S-heterocyclic compounds of crude fuels that are recalcitrant to the chemical treatments. The 4S or Dsz sulfur specific pathway for dibenzothiophene (DBT) and alkyl-substituted DBTs, widely used as model S-heterocyclic compounds, has been extensively studied at the physiological, biochemical and genetic levels mainly in Gram-positive bacteria. Nevertheless, several Gram-negative bacteria have been also used in BDS because they are endowed with some properties, e.g., broad metabolic versatility and easy genetic and genomic manipulation, that make them suitable chassis for systems metabolic engineering strategies. A high number of recombinant bacteria, many of which are Pseudomonas strains, have been constructed to overcome the major bottlenecks of the desulfurization process, i.e., expression of the dsz operon, activity of the Dsz enzymes, retro-inhibition of the Dsz pathway, availability of reducing power, uptake-secretion of substrate and intermediates, tolerance to organic solvents and metals, and other host-specific limitations. However, to attain a BDS process with industrial applicability, it is necessary to apply all the knowledge and advances achieved at the genetic and metabolic levels to the process engineering level, i.e., kinetic modelling, scale-up of biphasic systems, enhancing mass transfer rates, biocatalyst separation, etc. The production of high-added value products derived from the organosulfur material present in oil can be regarded also as an economically viable process that has barely begun to be explored.

Bioremediation of storage tank bottom sludge by using a two-stage composting system: Effect of mixing ratio and nutrients addition

The effect of mixing ratio and nutrients addition on the efficiency of a two-stage composting system in removal of total petroleum hydrocarbons (TPH) from storage tank bottom sludge (STBS) was investigated. The system consisted of ten windrow piles as primary composting (PC) followed by four in-vessel reactors as secondary composting (SC). Various initial C/N/P and mixing ratios of STBS to immature compost (IC) were examined in the PC and SC for 12 and 6weeks, respectively. The removal rates of TPH in the two-stage system (93.72-95.24%) were higher than those in the single-stage one. Depending on the experiments, TPH biodegradation fitted to the first- and second-order kinetics with the rate constants of 0.051-0.334d^-1 and 0.002-0.165gkg^-1d^-1, respectively. The bacteria identified were Pseudomonas sp., Bacillus sp., Klebsiella sp., Staphylococcus sp., and Proteus sp. The study verified that a two-stage composting system is effective in treating the STBS.

Bioelectroventing: an electrochemical-assisted bioremediation strategy for cleaning-up atrazine-polluted soils

The absence of suitable terminal electron acceptors (TEA) in soil might limit the oxidative metabolism of environmental microbial populations. Bioelectroventing is a bioelectrochemical strategy that aims to enhance the biodegradation of a pollutant in the environment by overcoming the electron acceptor limitation and maximizing metabolic oxidation. Microbial electroremediating cells (MERCs) are devices that can perform such a bioelectroventing. We also report an overall profile of the ¹⁴ C-ATR metabolites and ¹⁴ C mass balance in response to the different treatments. The objective of this work was to use MERC principles, under different configurations, to stimulate soil bacteria to achieve the complete biodegradation of the herbicide ¹⁴ C-atrazine (ATR) to ¹⁴ CO₂ in soils. Our study concludes that using electrodes at a positive potential [+600 mV (versus Ag/AgCl)] ATR mineralization was enhanced by 20-fold when compared to natural attenuation in electrode-free controls. Furthermore, ecotoxicological analysis of the soil after the bioelectroventing treatment revealed an effective clean-up in < 20 days. The impact of electrodes on soil bioremediation suggests a promising future for this emerging environmental technology.

A Pilot-scale Benthic Microbial Electrochemical System (BMES) for Enhanced Organic Removal in Sediment Restoration

A benthic microbial electrochemical systems (BMES) of 195 L (120 cm long, 25 cm wide and 65 cm height) was constructed for sediment organic removal. Sediment from a natural river (Ashi River) was used as test sediments in the present research. Three-dimensional anode (Tri-DSA) with honeycomb structure composed of carbon cloth and supporting skeleton was employed in this research for the first time. The results demonstrated that BMES performed good in organic-matter degradation and energy generation from sediment and could be considered for river sediments in situ restoration as novel method. Community analysis from the soil and anode using 16S rDNA gene sequencing showed that more electrogenic functional bacteria was accumulated in anode area when circuit connected than control system.

Cleaning-up atrazine-polluted soil by using Microbial Electroremediating Cells

Biodegradation of pollutants in soil is greatly limited by the availability of terminal electron acceptors required for supporting microbial respiration. Such limitation can be overcome if soil-buried electrodes accept the electrons released in the microbial metabolism. We propose the term bioelectroventing for such a environmental treatment. The process would be performed in a device so-called Microbial Electroremediating Cell. Indeed, our studies demonstrate that the presence of electrodes as electron acceptors effectively stimulated by 5-fold the biodegradation rate of the herbicide atrazine (2-chloro-4-ethylamino-6-isopropyl amino-1,3,5-triazine) in comparison with soil natural attenuation. Furthermore, a different set of toxicological test using Pseudokirchneriella subcapitata green alga e, Salmonella typhimorium bacteria and Sorghum saccharatum plant seeds respectively, confirm that atrazine-polluted soil can be effectively cleaned-up in short time by the use of MERCs.

Stimulating soil microorganisms for mineralizing the herbicide isoproturon by means of microbial electroremediating cells

The absence of suitable terminal electron acceptors (TEA) in soil might limit the oxidative metabolism of environmental microbial populations. Microbial electroremediating cells (MERCs) consist in a variety of bioelectrochemical devices that aim to overcome electron acceptor limitation and maximize metabolic oxidation with the purpose of enhancing the biodegradation of a pollutant in the environment. The objective of this work was to use MERCs principles for stimulating soil bacteria to achieve the complete biodegradation of the herbicide ¹⁴C‐isoproturon (IPU) to ¹⁴CO₂ in soils. Our study concludes that using electrodes at a positive potential [+600 mV (versus Ag/AgCl)] enhanced the mineralization by 20‐fold respect the electrode‐free control. We also report an overall profile of the ¹⁴C‐IPU metabolites and a ¹⁴C mass balance in response to the different treatments. The remarkable impact of electrodes on the microbial activity of natural communities suggests a promising future for this emerging environmental technology that we propose to name bioelectroventing.

A severe reduction in the cytochrome C content of Geobacter sulfurreducens eliminates its capacity for extracellular electron transfer

The ability of Geobacter species to transfer electrons outside the cell enables them to play an important role in a number of biogeochemical and bioenergy processes. Gene deletion studies have implicated periplasmic and outer-surface c-type cytochromes in this extracellular electron transfer. However, even when as many as five c-type cytochrome genes have been deleted, some capacity for extracellular electron transfer remains. In order to evaluate the role of c-type cytochromes in extracellular electron transfer, Geobacter sulfurreducens was grown in a low-iron medium that included the iron chelator (2,2'-bipyridine) to further sequester iron. Haem-staining revealed that the cytochrome content of cells grown in this manner was 15-fold lower than in cells exposed to a standard iron-containing medium. The low cytochrome abundance was confirmed by in situ nanoparticle-enhanced Raman spectroscopy (NERS). The cytochrome-depleted cells reduced fumarate to succinate as well as the cytochrome-replete cells do, but were unable to reduce Fe(III) citrate or to exchange electrons with a graphite electrode. These results demonstrate that c-type cytochromes are essential for extracellular electron transfer by G. sulfurreducens. The strategy for growing cytochrome-depleted G. sulfurreducens will also greatly aid future physiological studies of Geobacter species and other microorganisms capable of extracellular electron transfer.