A novel method for synthesis of polyaniline and its application for catalytic degradation of atrazine in a Fenton-like system

Iron-doped bismuth oxybromides as visible-light-responsive Fenton catalysts for the degradation of atrazine in aqueous phases

Pesticides and its degradation products, being well-known residues in soil, have recently been detected in many water bodies as pollutants of emerging concerns, and thus there is a contemporary demand to develop viable and cost-effective techniques for the removal of related organic pollutants in aqueous phases. Herein, a visible-light-responsive Fenton system was constructed with iron-doped bismuth oxybromides (Fe-BiOBr) as the catalysts. Taking the advantage of sustainable Fe(III)/Fe(II) conversion and optimized H2O2 utilization, the optimal Fe-BiOBr-2 catalyst showed an excellent atrazine removal efficiency of 97.61% in 120 min, which is superior than the traditional homogeneous Fenton and the majority of heterogeneous processes documented in the literature. In this photo-Fenton system, hydroxyl (·OH) and superoxide (·O2-) radicals were dominant active species contributed to the oxidative degradation of atrazine. Due to the production of various active radicals, five degradation pathways were proposed based on the identification of intermediates and degradation products. Overall, this work not only demonstrates a fundamental insight into creating highly efficient and atom economic photo-Fenton systems, but also provides a complementary strategy for the treatment of organic pollutants in water.

Synthesis and Characterization of a Novel Nanosized Polyaniline

Polyaniline (PANI) is a conductive polymer easily converted into a conducting state. However, its limited mechanical properties have generated interest in fabricating PANI composites with other polymeric materials. In this study, a PANI-prevulcanized latex composite film was synthesized and fabricated in two phases following chronological steps. The first phase determined the following optimum parameters for synthesizing nanosized PANI, which were as follows: an initial molar ratio of 1, a stirring speed of 600 rpm, a synthesis temperature of 25 °C, purification via filtration, and washing using dopant acid, acetone, and distilled water. The use of a nonionic surfactant, Triton X-100, at 0.1% concentration favored PANI formation in a smaller particle size of approximately 600 nm and good dispersibility over seven days of observation compared to the use of anionic sodium dodecyl sulfate. Ultraviolet-visible spectroscopy (UV-Vis) showed that the PANI synthesized using a surfactant was in the emeraldine base form, as the washing process tends to decrease the doping level in the PANI backbone. Our scanning electron microscopy analysis showed that the optimized synthesis parameters produced colloidal PANI with an average particle size of 695 nm. This higher aspect ratio explained the higher conductivity of nanosized PANI compared to micron-sized PANI. Following the chronological steps to determine the optimal parameters produced a nanosized PANI powder. The nanosized PANI had higher conductivity than the micron-sized PANI because of its higher aspect ratio. When PANI is synthesized in smaller particle sizes, it has higher conductivity. Atomic force microscopy analysis showed that the current flow is higher across a 5 µm2 scanned area of nanosized PANI because it has a larger surface area. Thus, more sites for the current to flow through were present on the nanosized PANI particles.

Synthesis of β-FeOOH/polyaniline heterogeneous catalyst for efficient photo-Fenton degradation of AOII dye

Discharge of the untreated dye-containing wastewaters will induce water source pollution and further harm aquatic organisms. In this study, the akaganéite/polyaniline catalyst (β-FeOOH/PANI, about 1.0 μm) could be successfully composed by polyaniline (PANI, (C₆H₇N)_n, 200-300 nm) and akaganéite (β-FeOOH, FeO(OH)_1-xCl_x, less than 200 nm), according to the identification and characterization results of XRD, Ramon, FTIR, XPS, SEAD, EDS, and FESEM (or HRTEM). Due to PANI providing more photogenerated electrons, the β-FeOOH/PANI composite (compared with β-FeOOH) in photo-Fenton system had the more highly catalytic degradation capacity to Acid Orange II (AOII) under an optimal condition (7.5 mmol/L of H₂O₂ oxidant, 40 mg/L of AOII, 0.2 g/L of catalyst dosage, and pH 4.0). The AOII degradation kinetics could be well fitted by pseudo-first-order model. In photo-Fenton catalytic process of AOII dye, the ∙OH and h⁺ were the main reaction substances. The AOII in solutions could be gradually mineralized into non-toxic inorganic H₂O molecule and CO₂. The β-FeOOH/PANI catalyst also had a good reusable ability of about 91.4% AOII degradation after 4 runs. These results can provide a reference for synthesis of catalyst used in photo-Fenton system and the applications in degradation removal of organic dye from wastewaters.

Highly efficient photocatalytic overall water splitting on plasmonic Cu6Sn5/polyaniline nanocomposites

A plasmonic Cu₆Sn₅/polyaniline (Cu₆Sn₅/PANI) nanocomposite was synthesized by chemical reduction and hydrothermal methods. The best photocatalytic overall water splitting performance was achieved by the Cu₆Sn₅/PANI_3wt% composite, which contains 3 wt% PANI, which is approximately three times more than that of pure Cu₆Sn₅. Meanwhile, Cu₆Sn₅/PANI_3wt% exhibited excellent photocatalytic stability for water splitting during the stability investigation. The dramatic promotion of the photocatalytic activity performance can be ascribed to the cocatalyst PANI. The existence of PANI can remarkably promote the separation and transfer efficiency of the photoinduced electron-hole pairs, and therefore enhance the photocatalytic activity. Our results also verify that the photogenerated charge comes from plasmonic Cu₆Sn₅ with the surface plasmon resonance (SPR) effect, which is different from traditional semiconductor-based photocatalysts. This work sheds some light on plasmonic photocatalyst development and provides an alternative pathway for photocatalytic reactions.

Effects of iron plaque and fatty acids on the transfer of BDE-209 from soil to rice under iron mineral Fenton-like oxidation condition

To understand the effect mechanisms of iron plaque and fatty acids on the migration of PBDEs from soil to rice (Oryza sativa), pot experiments were conducted in the soil spiked with decabromodiphenyl ether (BDE-209) under the conditions of tourmaline and nano-goethite Fenton-like treatments. The results showed that iron mineral Fenton-like oxidation could effectively remove BDE-209 from rhizosphere soil, the highest removal rate obtained 89.29% with the addition of 0.4 mmol/L H₂O₂ and 8 g nano-goethite (G + 3H group). Iron mineral Fenton-like oxidation could produce iron plaque (IP) on rice roots and accumulate a part of contaminants on the surface of IP, further weakening BDE-209 uptake in the plants. Additionally, the occurrence of fatty acid variation induced by BDE-209 stress, iron mineral Fenton-like oxidation at high concentrations of H₂O₂ with 0.4 mmol/L affected the distribution of fatty acids in plant tissues, especially for C_18:0 fatty acid. While the IP on rice roots prevented the BDE-209 into plant, it was also closely related to the distribution of fatty acids in rice, altering BDE-209 accumulation in the rice. To safely use the iron mineral Fenton-like oxidation in the agricultural soil remediation, the safety of plant cells treated by mineral Fenton-like oxidation was evaluated using the transmission electron microscopy (TEM) and enzyme activity determination, which indicated that iron mineral Fenton-like oxidation would destroy the inner structures of plant cells, especially for G + 3H group.

Enhanced Oxygen Evolution via Electrochemical Water Oxidation using Conducting Polymer and Nanoparticle Composites

Nano-Co₃ O₄ was used for electrocatalytic water oxidation due to its promising features of better performance and low cost. An enhanced electrochemical water oxidation performance of the nanoparticles can be achieved by mixing them with other types of highly conductive nano/micro-structured materials. Conductive polymers would be one of the candidates to achieve this goal. Here, we report our recently developed nano-Co₃ O₄ and polypyrrole composites for enhanced electrochemical water oxidation. We chose polypyrrole as a support of nano-Co₃ O₄ to obtain highly active sites of nano-Co₃ O₄ with high conductivity. Morphological and chemical characterization of the prepared materials were performed using scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). After immobilizing them individually on fluorine doped tin oxide (FTO) substrate, their electrocatalytic properties toward water oxidation were investigated. The optimum composite materials showed significantly higher electrocatalytic properties compared to that of pure nano-Co₃ O₄ and polypyrrole. Electrochemical impedance studies indicated that the composite materials possess significantly less electron transfer resistance toward water oxidation reaction compared to that of only polypyrrole or nano-Co₃ O₄ , while the higher double-layer capacitance and polarization resistance values obtained from fitting of the impedance data represent the faster electrode kinetics in the composite electrocatalyst. Due to the synergetic effect, the optimum nano-Co₃ O₄ and polypyrrole composites could be represent a novel and promising material for water oxidation.

Transformation of tetracyclines induced by Fe(III)-bearing smectite clays under anoxic dark conditions

Smectite clays are widely found in subsurface soils and waters. Although they strongly sequester tetracyclines (TCs), little is known about their reactions with these antibiotics under dark anoxic conditions. This study investigated the interactions between TCs and Fe-bearing smectite clays and the influences of environmental factors. Fe-bearing smectite clays were shown to significantly induce the transformation of TCs, including tautomerization, dechlorination, and dehydration. Moreover, the adsorbed TCs reduced the structural Fe(III) in clay particles to structural Fe(II) through electron transfer. The transformation of TCs was more readily induced by smectite clays with a higher rather than a lower Fe content. Tetrahedral Fe(III), and distorted cis- or trans-octahedral Fe(III), were more reactive as an electron acceptor than cis-octahedral Fe(III), as observed on the Mössbauer and FTIR spectra. A lower pH facilitated the adsorption of TCs through dimethyl-amino, amide, and conjugated -OH functional groups and induced a higher rate of TCs transformation. The transformation of chlortetracycline (CTC) was faster than that of oxytetracycline or tetracycline (TTC) due to -Cl substitution. The major transformation CTC products included keto-CTC, epi-CTC, iso-CTC, anhydro-CTC and TTC. Mixtures of these transformed products were found to have a higher acute toxicity than their parent compounds to Photobacterium phosphoreum T3. Our study revealed several previously overlooked interactions between TCs and clay particles that could cause these antibiotics to become unstable in the subsurface environment, with negative effects on the soil-borne microbial community.

The design of a polyaniline-decorated three dimensional W18O49 composite for full solar spectrum light driven photocatalytic removal of aqueous nitrite with high N2 selectivity

Photocatalysis using solar energy is the most promising green technology for nitrite removal. However, effective photocatalytic performance is often challenged by the limited light absorption, utilization of expensive noble metals and undesired products (nitrate and ammonium). Here, we report for the first time that a full solar light response polyaniline-decorated three dimensional W₁₈O₄₉ composite (PANI@W₁₈O₄₉), a noble metal-free photocatalyst, possesses excellent photocatalytic activity for aqueous nitrite removal with high N₂ selectivity. The prepared sample was thoroughly identified via XRD, Raman, FTIR, SEM, TEM, UV-vis DRS and PL. The catalytic results demonstrated that over 80% N₂ selectivity (initial concentration 1.0 mM) was achieved through the PANI@W₁₈O₄₉ without sacrificial agent under 300 W Xe lamp irradiation for 60 min. Such advantages were attributed to the built-in junction between n-type W₁₈O₄₉ and p-type PANI, offering suitable redox levels of electron-hole pairs for NO₂^- reaction. The modification of PANI also benefited the light harvesting ability and activated carriers migration, the calculated rate constant of PANI@W₁₈O₄₉ is about four times as high as that of W₁₈O₄₉. The current study not only prepared a promising photocatalyst, but also provides new insights into improving the photocatalytic activity and N₂ selectivity for nitrite treatment.

Degradation of atrazine by catalytic ozonation in the presence of iron scraps: performance, transformation pathway, and acute toxicity

Degradation of atrazine by catalytic ozonation in the presence of iron scraps (ZVI/O₃) was carried out. The key operational parameters (i.e., initial pH, ZVI dosage, and ozone dosage) were optimized by the batch experiments, respectively. This ZVI/O₃ system exhibited much higher degradation efficiency of atrazine than the single ozonation, ZVI, and traditional ZVI/O₂ systems. The result shows that the pseudo-first-order constant (0.0927 min^-1) and TOC removal rate (86.6%) obtained by the ZVI/O₃ process were much higher than those of the three control experiments. In addition, X-ray diffraction (XRD) analysis indicates that slight of γ-FeOOH and Fe₂O₃ were formed on the surface of iron scrap after ZVI/O₃ treatment. These corrosion products exhibit high catalytic ability for ozone decomposition, which could generate more hydroxyl radical (HO^•) to degrade atrazine. Six transformation intermediates were identified by liquid chromatography-mass spectrometry (LC-MS) analysis in ZVI/O₃ system, and the degradation pathway of atrazine was proposed. Toxicity tests based on the inhibition of the luminescence emitted by Photobacterium phosphoreum and Vibrio fischeri indicate the detoxification of atrazine by ZVI/O₃ system. Finally, reused experiments indicate the approving recyclability of iron scraps. Consequently, the ZVI/O₃ system could be as an effective and promising technology for pesticide wastewater treatment.

One-step solvothermal fabrication of Cu@PANI core-shell nanospheres for hydrogen evolution

Polyaniline(PANI)-decorated Cu nanoparticles were prepared by a facile solvothermal method. Different reaction temperatures resulted in different morphologies of the Cu/PANI composites, which exhibited good photocatalytic activities. When the mass ratio of PANI increased to 2.5 wt%, the H2 evolution rate reached 1.97 mmol g-1 h-1 in lactic acid solution under solar light irradiation, which is about 2 times higher than that of pure Cu nanoparticles (1.06 mmol g-1 h-1). The introduction of PANI can improve the separation efficiency of the photo-generated electron-hole pairs, where PANI acts as a hole reservoir for trapping holes generated by the Cu NPs and hindering the recombination of the electron-hole pairs. A possible mechanism is presented to explain the photocatalytic process using Cu@PANI core-shell nanospheres as the photocatalyst.