Simultaneous degradation of the anticancer drugs 5-fluorouracil and cyclophosphamide using a heterogeneous photo-Fenton process based on copper-containing magnetites (Fe3-xCuxO4)

Temperature-Induced Irreversible Structural Transition in Fe1.1Mn1.9O4 Nanoparticles Synthesized by Combustion Method

Fe_1.1Mn_1.9O₄ nanoparticles were successfully synthesized using a combustion method. The influence of the heating temperature on the evolution of the structural and magnetic properties has been studied using various methods. The structural analysis results revealed that as-synthesized nanoparticles have a tetragonal structure with an average size of ~24 nm. The magnetic measurements of the sample showed its ferrimagnetic nature at room temperature with hysteresis at low fields. Temperature-dependent magnetization measurements allowed for the conclusion that the Curie temperature for Fe_1.1Mn_1.9O₄ nanoparticles was ~465 °C. After high-temperature magnetic measurements, during which the samples were heated to various maximum heating temperatures (T_max.heat.) in the range from 500 to 900 °C, it was found that the structure of the samples after cooling to room temperature depended on the heating temperature. Herewith, when the heating temperature was 600 < T_max.heat. < 700 °C, an irreversible structural phase transition occurred, and the cooled samples retained a high-temperature cubic structure. The results of the magnetic analysis showed that the samples, following high-temperature magnetic measurements, demonstrated ferrimagnetic behavior.

Magnetite Nanoparticles as Solar Photo-Fenton Catalysts for the Degradation of the 5-Fluorouracil Cytostatic Drug

Heterogeneous catalysts based on magnetite nanoparticles, Fe3O4, were prepared by the chemical coprecipitation method using iron (III) chloride as a salt precursor. The physicochemical properties of the nanoparticles were determined by different techniques and the efficiency was evaluated for the degradation of the cytostatic drug, 5-fluorouracil (5-FU), in aqueous solution by photo-Fenton process under simulated solar radiation. The most influential parameters, namely pH of the solution, catalyst load, H2O2 dosage, and use of radiation, were studied and optimized in the degradation process. The optimal conditions to achieve a 100% degradation of 5-FU (10 mg L-1) and a high mineralization degree (76%) were established at the acidic pH of 3.0, 100 mg L-1 of catalyst loading, and 58 mM of H2O2 under simulated solar radiation. The contribution of iron leaching to the catalyst deactivation, the role of the dissolved iron ions on homogenous reactions, and the stability of the catalyst were assessed during consecutive reaction cycles.

Ca and Cu doped LaFeO3 to promote coupling of photon carriers and redox cycling for facile photo-Fenton degradation of bisphenol A

Enhancements in the light response and hydrogen peroxide utilization are critical to the catalytic performance of heterogeneous Fenton-like perovskites. Here, in this research, oxygen vacancy-enriched La_0.9Ca_0.1Cu_0.5Fe_0.5O_3-δ was prepared by a co-precipitation method with Cu substitution and Ca doping and demonstrated excellent performance for the degradation of bisphenol A. Both total organic carbon (TOC) removal and hydrogen peroxide utilization were close to 90% within 120 min at pH 3-7, where the TOC removal and hydrogen peroxide utilization were 2.5 times and 5.5 times of LaFeO₃ in the absence of Ca and Cu doping. It demonstrated excellent stability to light irradiation and oxidation with respect to cycling and metal ion leaching. This revealed that oxygen vacancies were enriched in the catalyst with the substitution of Ca and Cu and contributed to the recombination of photogenerated electrons, thereby increasing the reduction efficiency of copper ions and accelerating the redox cycling of iron ions.

Trends in Fenton and photo-Fenton processes for degradation of antineoplastic agents in water matrices: current knowledge and future challenges evaluation using a bibliometric and systematic analysis

Antineoplastic agents present potential hazards to human health and the environment. For this reason, these compounds have attracted a great deal of attention from researchers in the environmental sciences field. In order to help guide future research, it is important to understand the current state of investigation of the occurrence of these microcontaminants and methods for their removal, especially focusing on Fenton and photo-Fenton processes applied to various aqueous matrices in which this class of pharmaceuticals is present. For this purpose, a systematic review of these topics was performed by bibliometric analysis of articles published during the last decade and available in the Scopus and Web of Science databases. This study enables visualization of the current panorama and trends in this field, providing a guide for future collaborative research and exchange of knowledge. Various strategies have been suggested to improve the efficiency of Fenton and photo-Fenton processes, mainly by means of the application of multiples additions of iron, the use of heterogeneous catalysts, and/or the use of chelating agents. Some studies have evaluated different radiation sources employed for photo-Fenton processes, such as solar and/or artificial radiation. In turn, the identification of transformation products generated by Fenton and photo-Fenton treatments, together with their evaluation by in silico (Q)SAR predictions or experimental toxicological bioassays, are related subjects that have been less reported in published works and that should be studied in depth. These subjects can support treatment evaluations that are more realistic, considering their limitations or potentials.

Investigation of the Degradation Behavior of Cyclophosphamide by Catalytic Ozonation Based on Mg(OH)2

Metal hydroxides, owing to their catalytic active sites for the decomposition of O3 to Reactive Oxygen Species (ROS), have been adapted for catalytic ozonation of micropollutants in wastewater. In this study, commercial Mg (OH)2 was used for the degradation of cyclophosphamide (CYP) by ozone. The crystal phase was confirmed by X-ray powder Diffraction (XRD). Percent degradation of 10 ppm CYP after 30 min by O3 and Mg (OH)2/O3 was 56 and 93, respectively, suggesting enhanced decomposition of O3 to ROS by the catalyst. The presence of ROS was further confirmed using pCBA as a probe, which showed that the concentration of ROS was eight times higher in the presence of Mg (OH)2/O3 than O3 alone. Catalytic ozonation experiments in the presence of scavengers showed that OH· radicals play a significant role in the degradation of CYP. The catalyst was found to be reusable for at least three cycles without significant loss in degradation efficiency. To study the compatibility of Mg (OH)2 for wastewater treatment applications, synthetic effluent was spiked with CYP and subjected to ozonation by Mg(OH)2/O3. The TOC of CYP before and after the treatment showed that Mg (OH)2/O3 not only degrades CYP but also mineralizes to a certain extent unlike O3 alone.

Heterogeneous Advanced Oxidation Processes: Current Approaches for Wastewater Treatment

Nowadays, water pollution is one of the most dangerous environmental problems in the world. The presence of the so-called emerging pollutants in the different water bodies, impossible to eliminate through conventional biological and physical treatments used in wastewater treatment plants due to their persistent and recalcitrant nature, means that pollution continues growing throughout the world. The presence of these emerging pollutants involves serious risks to human and animal health for aquatic and terrestrial organisms. Therefore, in recent years, advanced oxidation processes (AOPs) have been postulated as a viable, innovative and efficient technology for the elimination of these types of compounds from water bodies. The oxidation/reduction reactions triggered in most of these processes require a suitable catalyst. The most recent research focuses on the use and development of different types of heterogeneous catalysts, which are capable of overcoming some of the operational limitations of homogeneous processes such as the generation of metallic sludge, difficult separation of treated water and narrow working pH. This review details the current advances in the field of heterogeneous AOPs, Fenton processes and photocatalysts for the removal of different types of emerging pollutants.

Comparative degradation of 5-fluorouracil in aqueous solution by using H2O2-modified subcritical water, photocatalytic oxidation and electro-Fenton processes

This study investigated the degradation of the antineoplastic agent 5-fluorouracil (5-FU) widely applied to treat different cancers using different advanced oxidation processes such as electro-Fenton (EF), photocatalysis with TiO_2, and H₂O₂-modified subcritical water oxidation. The treatment with the EF process was the most efficient compared to others. Interestingly, in the EF process, the oxidative degradation of 5-FU behaved differently depending on the anode used. At low currents (20 and 40 mA), Pt and DSA anodes performed better than BDD and Ti₄O₇ anodes. In contrast, at the higher current of 120 mA, the production of heterogeneous hydroxyl radicals (M(^•OH)) became important and contributed significantly to the oxidation of 5-FU in addition to homogeneous ^•OH generated in the bulk solution. These latter have high O₂-evolution overpotential leading to the high amount of physisorbed M(^•OH) compared to Pt and DSA. The oxidative degradation of 5-FU was then performed by titanium dioxide-based photocatalytic oxidation and subcritical water oxidation processes, both of which showed a lower degradation efficiency and failed to achieve complete mineralization. Finally, a comparison was performed in laboratory-scale, taking into account the following performance indicators: the degradation efficiency, the mineralization power, the cost of equipment and reagents, and the energy required for the treatment of 5-FU.

Engineered magnetic oxides nanoparticles as efficient sorbents for wastewater remediation: a review

The rapid urbanization and industrialization is causing worldwide water pollution, calling for advanced cleaning methods. For instance, pollutant adsorption on magnetic oxides is efficient and very practical due to the easy separation from solutions by an magnetic field. Here we review the synthesis and performance of magnetic oxides such as iron oxides, spinel ferrites, and perovskite oxides for water remediation. We present structural, optical, and magnetic properties. Magnetic oxides are also promising photocatalysts for the degradation of organic pollutants. Antimicrobial activities and adsorption of heavy metals and radionucleides are also discussed.

The treatment of electroplating wastewater using an integrated approach of interior microelectrolysis and Fenton combined with recycle ferrite

Heavy metal ions in chelated forms have aroused great concerns because of their high solubility, poor biodegradation and extreme stability. In this research, an efficient strategy, interior microelectrolysis-Fenton-recycle ferrite (IM-Fenton-RF), was developed to treat simulated electroplating wastewater containing chelated copper at room temperature. The decomplexation of chelated copper was carried out by both interior microelectrolysis and Fenton reactions. IM process can not only partly degrade the complexes of chelated copper via the microelectrolysis reaction but also it produces Fe²⁺ ions for the Fenton reaction. After decomplexation, the IM-Fenton effluent directly flowed into the RF reactor for copper ions removal. Under optimum reaction conditions (reflux ratio = 0.37, Fe²⁺ concentration = 9.20 g/L at pH 10.18), 99.9% copper was removed by the IM-Fenton-RF system. The produced IM-Fenton-RF sludge is based on ferrite precipitate and has several advantages over metal hydroxides sludge. Ferrite sludge is stable owing to the stability of ferrite's crystal structure, while the toxicity characteristic leaching procedure (TCLP) test meets relevant standards. The sedimentation rate and volume of ferrite sludge were 3.86 times faster and 11.0 times lower than those of metal hydroxides sludge. Furthermore, the yielding sludge of ferrite can be recovered and utilized for the synthesis of Fe-C metallic species, the main compound of IM packing for interior microelectrolysis reaction. All these results show that a combination of IM-Fenton and RF is an effective approach to treat wastewater containing chelated copper, showing great potential for industrial applications.

Magnetic copper smelter slag as heterogeneous catalyst for tetracycline degradation: Process variables, kinetics, and characterizations

The treatment of solid wastes and wastewater for sustainable development has been a hot topic. This work proposes a novel process of "waste treating waste" using magnetic copper smelter slag (CSS) as heterogeneous catalyst. The effect of process variables and water matrix was studied on catalytic performance. Under conditions of CSS 10 g/L, H₂O₂ 100 mM, pH 4.4, and temperature 25 °C, tetracycline can be effectively degraded within 30 min. The apparent rate constant is comparable to or higher than previous reports, and the activation energy is 37 kJ/mol. The broad operation pH, slight effect of water matrix, and magnetic property of CSS are favorable for potential application. CSS was characterized by N₂ adsorption-desorption isotherm, SEM-EDS, XRD, XPS, ICP and zeta potential. The dominant components of CSS are fayalite and magnetite, and the major metals of Fe and Cu provide active sites for H₂O₂ activation. Hydroxyl radical generated by H₂O₂ activation is dominant oxidative specie for tetracycline degradation. The plausible mechanism of tetracycline degradation in the solution and on catalyst surface is proposed.

A new approach on synergistic effect and chemical stability of graphene oxide-magnetic nanocomposite in the heterogeneous Fenton degradation of caffeine

Two compositions of graphene oxide-magnetite nanocomposites were studied as catalysts in the heterogeneous Fenton process. Transmission electron microscopy and X-ray diffraction revealed that the graphene oxide sheets were covered with nanoparticles of magnetite, with an average crystallite size of 7 nm. Infrared spectroscopy analysis indicated that the phases interacted through covalent Fe-O-C bonds. The composites presented significantly improved catalytic activity, compared to pure magnetite, with a synergistic effect of up to a factor of 17.1 for the Fenton degradation of caffeine, achieving total removal after 90 min. This synergistic effect was a consequence of the interaction between the phases, resulting in improved mass transfer of caffeine to the catalyst surface, adsorption and efficient degradation, with enhanced HO^• generation. The surface reaction constant increased by up to three orders of magnitude, demonstrating the important role of graphene oxide in the degradation kinetics of the heterogeneous Fenton process. The surface-bonded hydroxyl radicals were responsible for caffeine degradation, achieving 9.4 μmol L^-1. After five degradation cycles, a loss of Fe-O-C bonds and increase in oxygenated groups were associated with a small decrease of caffeine removal efficiency, from 98 to 82%, without significant iron leaching, in the dark, and with low consumption of hydrogen peroxide.

Bisphenol A degradation using waste antivirus copper film with enhanced sono-Fenton-like catalytic oxidation

This study investigated the applicability of waste antivirus copper film (CF) as a Fenton-like catalyst. The reaction activity of H₂O₂ and CF in combination was significantly enhanced by ultrasound (US) irradiation, and the synergy factor calculated from bisphenol A (BPA) degradation using CF-H₂O₂-US was 9.64 compare to that of dual factors. Photoluminescence analyses were conducted to compare the generation of hydroxyl radicals during both processes. In this sono-Fenton-like process, BPA degradation was affected by solution pH, temperature, ultrasound power, CF size, H₂O₂ dose, and initial BPA concentration. The BPA degradation curves showed an induction period (first stage) and a rapid degradation period (second stage). Process efficiency was totally and partially enhanced in the presence of chloride and carbonate ions, respectively. Chemical scavenger tests showed that both free and surface-bound hydroxyl radicals participate in BPA degradation under the sono-Fenton-like process using CF. The functional groups and copper crystals on the CF surface remained unchanged after five consecutive reuses, and the BPA degradation efficiency of CF was maintained over 80% during the reuse processes as a sono-Fenton-like catalyst.

Catalytic activity comparison of natural ferrous minerals in photo-Fenton oxidation for tertiary treatment of dyeing wastewater

Natural ferrous minerals are readily available and recyclable catalysts in photo-Fenton-like oxidation for wastewater treatment. In this work, typical ferrous oxide and sulfide minerals including magnetite, chalcopyrite, and pyrrhotite were exploited as catalysts in heterogeneous photo-Fenton oxidation for purification of biological effluent of dyeing wastewater. In a wide initial pH range (3.0~7.5), ferrous mineral-based heterogeneous photo-Fenton-like reactions were proven to be effective on the oxidation of recalcitrant pollutants. COD removals achieved 60.57%, 58.83%, and 57.41% using pyrrhotite, chalcopyrite, and magnetite, respectively, as catalyst under ultraviolet irradiation of 220~275 nm at H₂O₂ concentration of 9.8 mM. The corresponding COD removals were 51.75% and 34.09% with or without ferrous sulfate additions in UV/H₂O₂ systems. Minerals exhibited excellent stability and reusability with photo-catalytic activity reduction of less than 10% in the reuse of 5 cycles. Dissolved iron concentrations were determined to be 1.86 mg L^-1, 4.62 mg L^-1, and 7.53 mg L^-1 for magnetite, chalcopyrite, and pyrrhotite, respectively, at pH 3 and decreased to zero in neutral pH environment, which were much lower than those required for homogenous Fenton reaction. It was deduced that oxidation of recalcitrant pollutants was mainly catalyzed by Fe(II) on the mineral surface. The more reactive oxygen species such as hydroxyl radicals were resulted from the reaction of surface Fe (II) with H₂O₂, H₂O₂ photolysis, and charge separation of minerals under UV irradiation.

NiMoO4 nanorods photocatalytic activity comparison under UV and visible light

Waste water remediation is the ongoing hot research topic that can reduce the water scarcity all over the world. By reducing the pollutants in the waste water drawn from industries and other sources will be more useful for domestic purposes. To reduce the rate of pollutants in water may also help in improving the aquatic environment and decreases other side effects. Efficient and cost effective catalysts were in search for both dye degradation and water remediation treatment applications. NiMoO4 nanorods were prepared by employing co-precipitation method with different stirrer time (2 h, 4 h and 6 h). The formation of NiMoO4 was substantiated employing X-ray diffractometer analysis (XRD). Vibrational and rotational property of the samples was analyzed by FT-IR spectra and Raman spectra. The optical property was further confirmed by UV-vis spectral studies. Morphological analysis studies revealed growth of nanorods with 6 h stirrer time. The photocatalytic behavior of the obtained product was carried out under both UV light (364 nm) and visible light irradiation. The samples subjected to visible light environment showed better efficiency on degrading the methylene blue (MB) dye. The efficiency obtained under UV irradiation were 20%, 31%, 33%, 41% and efficiency obtained in visible light irradiation were 27%, 42%, 46%, 55% with respect to bare methylene blue (MB), MB with NiMoO4 (2 h), MB with NiMoO4 (4 h), MB with NiMoO4 (6 h) catalyst added. NiMoO4 sample with 6 h stirrer time and fine nanorods growth will be the good candidate for future use.

Multifunctional magnetite nanoparticles for drug delivery: Preparation, characterisation, antibacterial properties and drug release kinetics

Multifunctional nanoparticles (NPs) with magnetic (M) and antibacterial properties were prepared for drug delivery purposes by a method involving co-precipitation synthesis. Partial and complete substitutions of ferrous ions (Fe²⁺) by copper ions (Cu²⁺) were carried out for the preparation of the magnetite NPs, which are designated as Cu_0.5M and CuM, respectively, in this work. In addition, chitosan and ciprofloxacin were hybridized with the NPs from the previous step to achieve multifunctional properties. XRD, TEM, SEM/EDAX, VSM and FTIR were subsequently employed to characterize various properties of the prepared NPs, namely, crystallinity, nanostructure (size), particle morphology, elemental mapping, magnetic strength and chemical composition. Antibacterial properties of the NPs were tested against Bacillus cereus (Gram-positive bacteria), Escherichia coli (Gram-negative bacteria) and Candida albicans (yeast). Efficiency of the ciprofloxacin release was also studied for the drug-loaded NPs. It is demonstrated that the obtained NPs possess mixed phases with crystalline structures that are affected by the degree of Cu ion substitution (5-10 nm (M), 2.5-3.5 nm (Cu_0.5M) and 11-16 nm (CuM)). Saturation magnetization values of the NPs were recorded as 38.7, 3.5 and 1.3 emu/g, respectively. It was also found that the introduction of Cu ions in the NP samples improved the significance of their antibacterial activity, especially against Escherichia coli. Chitosan and ciprofloxacin were found to have stronger effects against Bacillus cereus and Escherichia coli and lesser effects against Candida albicans. However, the samples containing chitosan, ciprofloxacin and the higher Cu ion concentration exhibited strong influence against Candida albicans. During a study period of 30-days, the amounts of released drug from the tested NPs were 85, 26 and 20% of the originally loaded amount, respectively. Owing to the findings in this paper, the developed NPs are considered to have good potential for drug delivery applications and to study them further such as in pre-clinical studies.

Rhodamine B dye is efficiently degraded by polypropylene-based cerium wet catalytic materials

Polypropylene-based cerium wet catalytic materials (Ce/PPNW-g-PAA) were prepared through ultraviolet grafting and ion exchange technology. They were used as effective and reusable heterogeneous catalysts for rhodamine B (RhB) degradation. The physicochemical properties of Ce/PPNW-g-PAA were characterized by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), specific surface area measurements (BET), and X-ray photoelectron spectroscopy (XPS). The catalytic capacity of the Ce/PPNW-g-PAA-H2O2 system for the removal of RhB was tested in comparison with several other systems, which demonstrated that Ce/PPNW-g-PAA effectively promoted the oxidation and degradation of RhB by catalytic wet H2O2 oxidation. The results of the RhB degradation showed that Ce/PPNW-g-PAA exhibited excellent degradation performance by achieving a high removal rate for RhB (97.5%) at an initial RhB concentration of 100 mg L-1, H2O2 dosage of 5.0 mmol, Ce/PPNW-g-PAA dosage of 0.15 g L-1, and initial pH of 5.0 at 298 K. The degradation of RhB by Ce/PPNW-g-PAA conformed to the first-order kinetic reaction model. Consecutive experiments performed with the Ce/PPNW-g-PAA sample showed little activity decay, further confirming the high stability of the catalyst. In addition, the possible degradation mechanism of RhB was also investigated by XPS and electron paramagnetic resonance. The results suggested that Ce3+ and hydroxyl radical played important roles during the RhB degradation process.