Accelerated anaerobic biodecolorization of sulfonated azo dyes by magnetite nanoparticles as potential electron transfer mediators

Treatment of azo dye-containing wastewater in a combined UASB-EMBR system: Performance evaluation and membrane fouling study

This work investigated the treatment of azo dye-containing wastewater in an upflow anaerobic sludge blanket (UASB) reactor combined with an electro-membrane bioreactor (EMBR). Current densities of 20 A m-2 and electric current exposure mode of 6'ON/30'OFF were applied to compare the performance of the EMBR to a conventional membrane bioreactor (MBR). The results showed that dye (Drimaren Red CL-7B) removal occurred predominantly in the UASB reactor, which accounted for 57% of the total dye removal achieved by the combined system. When the MBR was assisted by electrocoagulation, the overall azo dye removal efficiency increased from 60.5 to 67.1%. Electrocoagulation batch tests revealed that higher decolorization rates could be obtained with a current density of 50 A m-2. Over the entire experimental period, the combined UASB-EMBR system exhibited excellent performance in terms of chemical oxygen demand (COD) and NH4+-N removal, with average efficiencies above 97%, while PO43--P was only consistently removed when the electrocoagulation was used. Likewise, a consistent reduction in the absorption spectrum of aromatic amines was observed when the MBR was electrochemically assisted. In addition to improving the pollutants removal, the use of electrocoagulation reduced the membrane fouling rate by 68% (0.25-0.08 kPa d-1), while requiring additional energy consumption and operational costs of 1.12 kWh m-3 and 0.32 USD m-3, respectively. Based on the results, it can be concluded that the combined UASB-EMBR system emerges as a promising technological approach for textile wastewater treatment.

Harnessing iron materials for enhanced decolorization of azo dye wastewater: A comprehensive review

Highly colored azo dye-contaminated wastewater poses significant environmental threats and requires effective treatment before discharge. The anaerobic azo dye treatment method is a cost-effective and environmentally friendly solution, while its time-consuming and inefficient processes present substantial challenges for industrial scaling. Thus, the use of iron materials presents a promising alternative. Laboratory studies have demonstrated that systems coupled with iron materials enhance the decolorization efficiency and reduce the processing time. To fully realize the potential of iron materials for anaerobic azo dye treatment, a comprehensive synthesis and evaluation based on individual-related research studies, which have not been conducted to date, are necessary. This review provides, for the first time, an extensive and detailed overview of the utilization of iron materials for azo dye treatment, with a focus on decolorization. It assesses the treatment potential, analyzes the influencing factors and their impacts, and proposes metabolic pathways to enhance anaerobic dye treatment using iron materials. The physicochemical characteristics of iron materials are also discussed to elucidate the mechanisms behind the enhanced bioreduction of azo dyes. This study further addresses the current obstacles and outlines future prospects for industrial-scale application of iron-coupled treatment systems.

Insight into the mechanism of chlorinated nitroaromatic compounds anaerobic reduction with mackinawite (FeS) nanoparticles

Anaerobic biotechnology for wastewaters treatment can nowadays be considered as state of the art methods. Nonetheless, this technology exhibits certain inherent limitations when employed for industrial wastewater treatment, encompassing elevated substrate consumption, diminished electron transfer efficiency, and compromised system stability. To address the above issues, increasing interest is being given to the potential of using conductive non-biological materials, e,g., iron sulfide (FeS), as a readily accessible electron donor and electron shuttle in the biological decontamination process. In this study, Mackinawite nanoparticles (FeS NPs) were studied for their ability to serve as electron donors for p-chloronitrobenzene (p-CNB) anaerobic reduction within a coupled system. This coupled system achieved an impressive p-CNB removal efficiency of 78.3 ± 2.9% at a FeS NPs dosage of 1 mg/L, surpassing the efficiencies of 62.1 ± 1.5% of abiotic and 30.6 ± 1.6% of biotic control systems, respectively. Notably, the coupled system exhibited exclusive formation of aniline (AN), indicating the partial dechlorination of p-CNB. The improvements observed in the coupled system were attributed to the increased activity in the electron transport system (ETS), which enhanced the sludge conductivity and nitroaromatic reductases activity. The analysis of equivalent electron donors confirmed that the S2- ions dominated the anaerobic reduction of p-CNB in the coupled system. However, the anaerobic reduction of p-CNB would be adversely inhibited when the FeS NPs dosage exceeded 5 g/L. In a continuous operation, the p-CNB concentration and HRT were optimized as 125 mg/L and 40 h, respectively, resulting in an outstanding p-CNB removal efficiency exceeding 94.0% after 160 days. During the anaerobic reduction process, as contributed by the predominant bacterium of Thiobacillus with a 6.6% relative abundance, a mass of p-chloroaniline (p-CAN) and AN were generated. Additionally, Desulfomonile was emerged with abundances ranging from 0.3 to 0.7%, which was also beneficial for the reduction of p-CNB to AN. The long-term stable performance of the coupled system highlighted that anaerobic technology mediated by FeS NPs has a promising potential for the treatment of wastewater containing chlorinated nitroaromatic compounds, especially without the aid of organic co-substrates.

Enhancement of electron transfer via magnetite in nitrite-dependent anaerobic methane oxidation system

Nitrite-dependent anaerobic methane oxidation (n-DAMO) is a novel denitrification process that simultaneously further removes and utilizes methane from anaerobic effluent from wastewater treatment plants. However, the metabolic activity of n-DAMO bacteria is relative low for practical application. In this study, conductive magnetite was added into lab-scale sequencing batch reactor inoculated with n-DAMO bacteria to study the influence on n-DAMO process. With magnetite amendment, the nitrogen removal rate could reach 34.9 mg N·L-1d-1, nearly 2.5 times more than that of control group. Magnetite significantly facilitated the interspecies electron transfer and built electrically connected community with high capacitance. Enzymatic activities of electron transport chain were significantly elevated. Functional gene expression and enzyme activities associated with nitrogen and methane metabolism had been highly up-regulated. These results not only propose a useful strategy in n-DAMO application but also provide insights into the stimulating mechanism of magnetite in n-DAMO process.

Stimulating anaerobic digestion to degrade recalcitrant organic pollutants: Potential role of conductive materials-led direct interspecies electron transfer

This review aims to provide a comprehensive understanding of the potential of CMs-dominated DIET in the degradation of recalcitrant organic pollutants in AD. The review covers the mechanisms and efficiencies of recalcitrant organic pollutant degradation by CMs-dominated DIET, the comparison of degradation pathways between DIET and chemical treatment, recent insights on DIET-enhanced degradation, and the evaluation of the potential and future development of CMs-dominated DIET. The review emphasizes the importance of coupled syntrophic microorganisms, electron flux, and physicochemical properties of CMs in enhancing the degradation performance of AD. Additionally, it highlights the advantages of DIET-led syntrophic metabolism over traditional oxidation technologies in terms of environmental friendliness and efficiency. Finally, the review acknowledges the potential risks associated with introducing CMs into AD systems and provides guidance for waste treatment and energy recovery.

Enhanced detoxification of Cr6+ by Shewanella oneidensis via adsorption on spherical and flower-like manganese ferrite nanostructures

Maximizing the safe removal of hexavalent chromium (Cr6+) from waste streams is an increasing demand due to the environmental, economic and health benefits. The integrated adsorption and bio-reduction method can be applied for the elimination of the highly toxic Cr6+ and its detoxification. This work describes a synthetic method for achieving the best chemical composition of spherical and flower-like manganese ferrite (MnxFe3-xO4) nanostructures (NS) for Cr6+ adsorption. We selected NS with the highest adsorption performance to study its efficiency in the extracellular reduction of Cr6+ into a trivalent state (Cr3+) by Shewanella oneidensis (S. oneidensis) MR-1. MnxFe3-xO4 NS were prepared by a polyol solvothermal synthesis process. They were characterised by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), dynamic light scattering (DLS) and Fourier transform-infrared (FTIR) spectroscopy. The elemental composition of MnxFe3-xO4 was evaluated by inductively coupled plasma atomic emission spectroscopy. Our results reveal that the oxidation state of the manganese precursor significantly affects the Cr6+ adsorption efficiency of MnxFe3-xO4 NS. The best adsorption capacity for Cr6+ is 16.8 ± 1.6 mg Cr6+/g by the spherical Mn0.22+Fe2.83+O4 nanoparticles at pH 7, which is 1.4 times higher than that of Mn0.8Fe2.2O4 nanoflowers. This was attributed to the relative excess of divalent manganese in Mn0.22+Fe2.83+O4 based on our XPS analysis. The lethal concentration of Cr6+ for S. oneidensis MR-1 was 60 mg L-1 (determined by flow cytometry). The addition of Mn0.22+Fe2.83+O4 nanoparticles to S. oneidensis MR-1 enhanced the bio-reduction of Cr6+ 2.66 times compared to the presence of the bacteria alone. This work provides a cost-effective method for the removal of Cr6+ with a minimum amount of sludge production.

Effect of salinity on removal performance of anaerobic membrane bioreactor treating azo dye wastewater

Membrane bioreactor (MBR) is an attractive option method for treating azo dye wastewater under extreme conditions. The present study assessed the effect of salinity on the performance of anaerobic MBR in treating azo dye wastewater. Increased salinity showed adverse effects on the decolorization efficiency and chemical oxygen demand (COD) removal efficiency. The decolorization efficiency decreased from 95.8% to 82.3% and 73.1% with a stepwise increasing of salinity from 0 to 3% and 5%, respectively. The COD removal efficiency decreased from 80.7% to 71.3% when the salinity increased from 0 to 3% and then decreased to 58.6% at 5% salinity. The volatile fatty acids (VFAs) concentration also increased as the salinity increased. Furthermore, increased salinity led to the elevated production of soluble microbial products (SMP) and extracellular polymeric substances (EPS), which can provide a protective barrier against harsh environments. More serious membrane fouling was observed as the SMP and EPS concentrations increased. The concentration of loosely bound EPS (LB-EPS), tightly bound EPS (TB-EPS), and the polysaccharide/protein (PS/PN) ratios in LB-EPS and TB-EPS all increased when the salinity was elevated. The production of SMP and EPS was caused by the generation of PS in response to the saline environment. Lactobacillus, Lactococcus, Anaerosporobacter, and Pectinatus were the dominant bacteria, and Lactobacillus and Lactococcus were the decolorization bacteria in the MBR. The lack of halophilic bacteria was the main reason for the decreased decolorization efficiency in the salinity environment.

Performance enhancement and population structure of denitrifying phosphorus removal system over redox mediator at low temperature

The development of denitrifying polyphosphate accumulating organisms (DPAOs) presents a strategy to carbon competition between denitrifying bacteria and phosphorus removing bacteria. However, low temperature inhibits the rate of enzyme-catalyzed and substrate diffusion during denitrifying phosphorus removal (DPR). Therefore, the present study assessed the addition of NQS (100 μmol/L) for enhancing the removal of TP and TN in DPR reactors operated at alternating anaerobic and anoxic phases and different influent phosphate concentrations. The results showed that the removal efficiency of TP and TN in NQS-DPR system at 10 °C were 99.9% and 42.0%, respectively, which were 2.1 and 2.0 times higher than that of DPR system. Adding NQS significantly alleviated the increase of pH under anoxic condition and decreased the ORP value of the reactor, which in turn enhanced the PHAs accumulation process. The determination of functional genes (nirK, narG and phoD) showed that Dechloromonas, Lentimicrobium, and Terrimonas were the dominant functional bacteria in NQS-DPR system at 10 °C with the relative abundance of 3.09%, 2.99% and 2.28%, respectively. This study can provide valuable information for the effects of the addition of the redox mediator on denitrifying phosphorus removal technology.

Progress and prospects of applying carbon-based materials (and nanomaterials) to accelerate anaerobic bioprocesses for the removal of micropollutants

Carbon‐based materials (CBM), including activated carbon (AC), activated fibres (ACF), biochar (BC), nanotubes (CNT), carbon xenogels (CX) and graphene nanosheets (GNS), possess unique properties such as high surface area, sorption and catalytic characteristics, making them very versatile for many applications in environmental remediation. They are powerful redox mediators (RM) in anaerobic processes, accelerating the rates and extending the level of the reduction of pollutants and, consequently, affecting positively the global efficiency of their partial or total removal. The extraordinary conductive properties of CBM, and the possibility of tailoring their surface to address specific pollutants, make them promising as catalysts in the treatment of effluents containing diverse pollutants. CBM can be combined with magnetic nanoparticles (MNM) assembling catalytic and magnetic properties in a single composite (C@MNM), allowing their recovery and reuse after the treatment process. Furthermore, these composites have demonstrated extraordinary catalytic properties. Evaluation of the toxicological and environmental impact of direct and indirect exposure to nanomaterials is an important issue that must be considered when nanomaterials are applied. Though the chemical composition, size and physical characteristics may contribute to toxicological effects, the potential toxic impact of using CBM is not completely clear and is not always assessed. This review gives an overview of the current research on the application of CBM and C@MNM in bioremediation and on the possible environmental impact and toxicity.

Enhanced decolorization of dyeing wastewater in a sponges-submerged anaerobic reactor

This study was conducted to assess the potential of a sponges-submerged anaerobic baffled reactor (SS-ABR) for enhancing the processing performance of azo dye-contaminated wastewater. A lab-scale four-compartment SS-ABR, with a total volume of 10 L, was operated at 30 °C for 180 days. A total of 14 polyurethane sponges were added in each compartment to treat synthetic wastewater including a commercial azo dye Hellozol HSR Reactive Black. During the entire operation, in synthetic wastewater, starch was used as a sole carbon source, and the true color level was maintained at 1050 ± 98 Pt/Co. Meanwhile, the hydraulic retention time (HRT) and total COD (T-COD) in the influent were changed to evaluate the SS-ABR treatment performance. After the start-up phase, true color and T-COD removal efficiencies were recorded as 65 ± 3% and 83 ± 2%, 68 ± 5% and 81 ± 4%, and 70 ± 5% and 84 ± 2% for HRT and influent T-COD concentration of 18.6 h and 260 mg L^-1, 14.6 h and 260 mg L^-1, and 14.6 h and 460 mg L^-1, respectively. The microbial community analysis showed that bacterial groups involved in dye degradation, such as Clostridium sp., and sulfate-reducing bacteria Desulfomonile sp. and Desulfovibrio sp. were detected prominently in the SS-ABR. Interestingly, the SS-ABR exhibited the dominance of both Geobacter sp. and Methanosarcina sp., and their occurrences in all columns were proportional to each other, revealing the formation of syntrophic relationships.

Rare earth metal (Sm) doped zinc ferrite (ZnFe2O4) for improved photocatalytic elimination of toxic dye from aquatic system

Wastewater remediation is the serious topic that must be taken into concern which would be a most crucial problem that destroys the natural properties as well as it has some worse effect on living organisms. By doing better wastewater management, the scarcity of water for domestic purposes can be eventually managed. Dyes are main organic pollutant that must be removed from wastewater. Pristine, 1% Sm doped and 2% Sm doped ZnFe₂O₄ were prepared through simple co-precipitation method. The materials were further analyzed for its structure, optical properties, rotational properties and morphology studies. These analyses were investigated with respect to X-ray diffraction, UV-vis spectroscopy, photoluminescence and scanning electron microscopic studies. XRD pattern of Pristine, 1% Sm doped and 2% Sm doped ZnFe₂O₄ was matched with JCPDS Card #89-1012 with cubic phase. Bandgap energy of prepared samples were 1.7 eV, 1.65 eV and 1.47 eV. The prepared cationic dye was degraded with help of visible light irradiation. 2% Sm doped ZnFe₂O₄ nanoparticles easily removed 65% of dye within 1 h duration. 2% Sm doped ZnFe₂O₄ was tested for its reusability and efficiency was stable for more than three cycles. This shows the stability of the sample towards degrading the cationic dye. By the doping of Samarium, ZnFe₂O₄ nanoparticles enthusiastically removed cationic dye and it proves to be an efficient candidate in removing dyes and can help in wastewater treatment in upcoming era.