Brønsted-acid sites promoted degradation of phthalate esters over MnO2: Mineralization enhancement and aquatic toxicity assessment

Insight into the role of reactive species on catalyst surface underlying peroxymonosulfate activation by P-Fe2MnO4 loaded on bentonite for trichloroethylene degradation

In this study, bentonite supporting phosphorus-doped Fe2MnO4 (BPF) was synthesized and applied for PMS activation to degrade TCE. Morphology and structure characterization results indicated the successfully synthesized of BPF, and the BPF/PMS system not only featured high TCE removal (97.4%) but also high reaction rate constant (kobs = 0.0554 min-1) and PMS utilization (70.4%, kobs = 0.0228 min-1). According to the results of various experiments, massive oxygen vacancies on P-Fe2MnO4 alter its charge balance and facilitate the electron transfer process named adjacent transfer (direct electron capture by adsorbed PMS from adjacent TCE). Mn(III) is the main adsorption site for PMS, and the hydroxyl groups on the catalyst (Fe sites of P-Fe2MnO4, Si and Al sites of bentonite) can also offer binding sites for PMS. The hydrogen-bonded PMS on Fe(III) and Mn(III) sites will subsequently accept the discharged electrons to generate free radicals and high-valent metal species. Meanwhile, electron loss of HSO5- that chemically bonded to hydroxyl groups on bentonite will generate SO5•-, which will further produce 1O2 through self-bonding. the active species on the catalyst surface contribute 65% of TCE degradation in the heterogeneous catalytic oxidation system.

Freshwater water quality criteria for phthalate esters and recommendations for the revision of the water quality standards

With increasing urbanization and rapid industrialization, more and more environmental problems have arisen. Phthalates (PAEs) are the foremost and most widespread plasticizers and are readily emitted from these manufactured products into the environment. PAEs act as endocrine-disrupting chemicals (EDCs) and can have serious impacts on aquatic organisms as well as human health. In this study, the water quality criteria (WQC) of five PAEs (dimethyl phthalate (DMP), diethyl phthalate (DEP), dibutyl phthalate (DBP), butyl benzyl phthalate (BBP) and di(2-ethylhexyl) phthalate (DEHP)) for freshwater aquatic organisms were developed using a species sensitivity distribution (SSD) and a toxicity percentage ranking (TPR) approach. The results showed that long-term water quality criteria (LWQC) of PAEs using the SSD method could be 13.7, 11.1, 2.8, 7.8, and 0.53 μg/L, respectively. Criteria continuous concentrations (CCC) of PAEs were derived using the TPR method and determined to be 28.4, 13.1, 1.3, 2.5, and 1.6 μg/L, respectively. The five PAEs are commonly measured in China surface waters at concentrations between ng/L and μg/L. DBP, DEHP, and di-n-octyl phthalate (DnOP) were the most frequently detected PAEs, with occurrence rates ranging from 67% to 100%. The ecological risk assessment results of PAEs showed a decreasing order of risk at the national level, DEHP, DBP, DMP, DEP, DnOP. The results of this study will be of great benefit to China and other countries in revising water quality standards for the conservation of aquatic species.

The inherent nature of N/P heteroatoms in Sargassum fusiforme seaweed biochar enhanced the nonradical activation of peroxymonosulfate for acetaminophen degradation in aquatic environments

This study investigated the catalytic activity of biochar materials derived from algal biomass Sargassum fusiforme (S. fusiforme) for groundwater remediation. A facile single-step pyrolysis process was used to prepare S. fusiforme biochar (SFBCX), where x denotes pyrolysis temperatures (600 °C-900 °C). The surface characterization revealed that SFBC800 possesses intrinsic N and P heteroatoms. The optimum experimental condition for acetaminophen (AAP) degradation (>98.70%) was achieved in 60 min using 1.0 mM peroxymonosulfate (PMS), 100 mg L-1 SFBC800, and pH 5.8 (unadjusted). Moreover, the degradation rate constant (k) was evaluated by the pseudo-first-order kinetic model. The maximum degradation (>98.70%) of AAP was achieved within 60 min of oxidation. Subsequently, the k value was calculated to be 6.7 × 10-2 min-1. The scavenger tests showed that radical and nonradical processes are involved in the SFBC800/PMS system. Moreover, the formation of reactive oxygen species (ROS) in the SFBC800/PMS system was confirmed using electron spin resonance (ESR) spectroscopy. Intriguingly, both radical (O2•-, •OH, and SO4•-) and nonradical (1O2) ROS were formed in the SFBC800/PMS system. In addition, electrochemical studies were conducted to verify the electron transfer process of the nonradical mechanism in the SFBC800/PMS system. The scavenger and electron spin resonance (ESR) spectroscopy showed that singlet oxygen (1O2) is the predominant component in AAP degradation. Under optimal condition, the SFBC800/PMS system reached ∼81% mineralization of AAP within 5 min and continued to ∼85% achieved over 60 min of oxidation. Coexisting ions and different aqueous matrices were investigated to examine the feasibility of the catalyst system, and the SFBC800/PMS system was found to be effective in the remediation of AAP-contaminated groundwater, river water, and effluent water obtained from wastewater treatment plants. Moreover, the SFBC800-activated PMS system demonstrated reusability. Our findings indicate that the SFBC800 catalyst has excellent catalytic activity for AAP degradation in aquatic environments.

Novel calcium oxide activated peroxymonosulfate system for methylene blue removal: Identification of key influencing factors, transformation pathway and toxicity assessment

The activation of peroxymonosulfate (PMS) has gained significant interest in the removal of organic pollutants. However, traditional methods usually suffer from drawbacks such as secondary contamination and high energy requirements. In this study, we propose a green and cost-effective approach utilizing calcium oxide (CaO) to activate PMS, aiming to construct a simple and reliable PMS based advanced oxidation processes (AOPs). The proposed CaO/PMS system achieved fast degradation of methylene blue (MB), where the degradation rate of CaO/PMS system (0.24 min-1) was nearly 2.67 times that of PMS alone (0.09 min-1). Under the optimized condition, CaO/PMS system exhibited remarkable durability against pH changes, co-exists ions or organic matters. Furthermore, singlet oxygen (1O2) was identified as the dominant reactive oxygen species by electron paramagnetic resonance (EPR) and quenching tests. Accordingly, the degradation pathways of MB are proposed by combing the results of LC/MS analysis and density functional theory (DFT) calculations, and the predicted ecotoxicity of the generated byproducts evaluated by EOCSAR could provide systematic insights into the fates and environmental risks of MB. Overall, the study provides an eco-friendly and effective strategy for treating dyeing wastewater, which should shed light on the application of PMS based AOPs.

Polydopamine-modified MOF-5-derived carbon as persulfate activator for aniline aerofloat degradation

Residual flotation chemicals in beneficiation wastewater seriously threaten local ecosystems, such as groundwater or soil, and must be treated effectively. Currently, the degradation of organic pollutants using nitrided MOFs-derived carbon to activate persulfate (PDS) has attracted considerable attention. Hence, we developed a new synthetic strategy to load dopamine hydrochloride (PDA) onto MOF-5-derived porous carbon (PC) to form NPC, and the degradation of a typical flotation Aniline aerofloat (AAF) at high salinity by a low dose of the NPC/PDS system was investigated. Several characterization analyses such as TEM, XRD, Raman, FT-IR and XPS demonstrated that the nitrogen-rich indolequinone unit in PDA provided nitrogen to PC during the pyrolysis process. This enabled the core-shell structure of NPC and the synergy among the multiple components to induce the AAF degradation by PDS over a wide pH scale in a short period of time. It was deduced that the degradation of AAF by the NPC-8/PDS system was a non-radical pathway dominated by 1O2, which relied mainly on the conversion of superoxide radicals (O2•-) and surface-bound radicals. Among them, the pyridine N in the sp2 hybrid carbon was considered as a possible active site. This non-radical pathway was resistant to pH changes and background substances in the water, and well overcame the inhibition of the reaction by natural organic substances and inorganic anions in natural water. In this study, A novel approach to the synthesis of homogeneous MOFs nuclear-derived porous carbon was proposed and the application of MOFs-derived porous carbon for AAF remediation of mineral processing wastewater was broadened.

Peroxymonosulfate Activation by Cu-OMS-2 Nanofibers for Efficient Degradation of N-Containing Heterocycles in Aquatic Solution

In this research, the degradation of different types of N-containing heterocycle (NHC) contaminants by Cu-OMS-2 via peroxymonosulfate (PMS) activation in an aqueous environment was investigated. First, the effects of different reaction parameters were optimized using benzotriazole (BTR) as the model contaminant, and the optimal reaction conditions were 8 mM PMS, 0.35 g/L Cu-OMS-2, and 30 °C. Nine different types of NHC contaminants were effectively degraded under these reaction conditions, and the degradation efficiencies and the mineralization rates of those NHCs were more than 68 and 46%, respectively. Moreover, the Cu-OMS-2/PMS process presented excellent performance at a wide pH ranging from 3.0 to 11.0 and in the presence of some representative anions (NO3- and SO42-) and dissolved organic matter (fumaric acid). The inhibition sequence of anions on BTR removal during the Cu-OMS-2/PMS process was H2PO4- > HCO3- > Cl- > CO32- > NO3- > SO42-. It was also found that 74.5 and 71.3% BTR degradation rates were achieved in actual water bodies, such as tap water and Yellow River water, respectively. Besides, the Cu-OMS-2 heterogeneous catalyst had excellent stability and reusability, and the degradation rate of BTR was still at 77.0% after 5 cycles. Finally, electron paramagnetic resonance analysis and scavenging tests showed that 1O2 and SO4- • were the primary reactive oxygen species. Accordingly, Cu-OMS-2 nanomaterial was an efficient and sustainable heterogeneous catalyst to activate PMS for the decontamination of BTR in water remediation.

Magnetized algae catalyst by endogenous N to effectively trigger peroxodisulfate activation for ultrafast degraded sulfathiazole: Radical evolution and electron transfer

An innovative Fe-N co-coupled catalyst MN-2 was prepared from waste spirulina by co-pyrolysis as a highly active carbon-based catalyst for the activation of peroxydisulfate (PDS) for the degradation of sulfathiazole (ST). The protein-rich raw material Spirulina provided sufficient N during the pyrolysis process, thus achieving N doping without an additional nitrogen source, optimizing the interlayer structure of the biochar material and effectively inhibiting the leaching of the ligand metal Fe. MN-2 showed highly efficient catalytic activity for peroxydisulfate (PDS), with a degradation efficiency of 100% for ST within 30 min and a kinetic constant (kobs) reached 0.306 min-1, benefiting from the excellent adsorption ability of MN-2 forming MN-2-PDS* complexes and the electron transfer process generated by Fe3+ and Fe2+ cycling, oxygen-containing functional groups. The effects of PDS dosage, initial pH and coexisting anions on the oxidation process were also investigated. Free radical quenching, electron paramagnetic resonance and electrochemical measurements were employed to explain the hydroxyl (·OH) and sulfate (SO4·-) as the dominant active species and the electron transfer effect on the removal of ST. MN-2 maintained a ST removal rate of 84% after four recycling experiments, showing a high reusability performance. This work provides a simple way to prepare magnetized N-doped biochar, a novel catalyst (MN-2) for efficient activation of PDS for ST degradation, and a feasible method for removing sulfanilamide antibiotics in water environment.

Harnessing the power of natural minerals: A comprehensive review of their application as heterogeneous catalysts in advanced oxidation processes for organic pollutant degradation

The release of untreated wastewater into water bodies has become a significant environmental concern, resulting in the accumulation of refractory organic pollutants that pose risks to human health and ecosystems. Wastewater treatment methods, including biological, physical, and chemical techniques, have limitations in achieving complete removal of the refractory pollutants. Chemical methods, particularly advanced oxidation processes (AOPs), have gained special attention for their strong oxidation capacity and minimal secondary pollution. Among the various catalysts used in AOPs, natural minerals offer distinct advantages, such as low cost, abundant resources, and environmental friendliness. Currently, the utilization of natural minerals as catalysts in AOPs lacks thorough investigation and review. This work addresses the need for a comprehensive review of natural minerals as catalysts in AOPs. The structural characteristics and catalytic performance of different natural minerals are discussed, emphasizing their specific roles in AOPs. Furthermore, the review analyzes the influence of process factors, including catalyst dosage, oxidant addition, pH value, and temperature, on the catalytic performance of natural minerals. Strategies for enhancing the catalytic efficiency of AOPs mediated by natural minerals are explored, mainly including physical fields, reductant addition, and cocatalyst utilization. The review also examines the practical application prospects and main challenges associated with the use of natural minerals as heterogeneous catalysts in AOPs. This work contributes to the development of sustainable and efficient approaches for organic pollutant degradation in wastewater.

Efficient degradation of phenol by MnOOH-rGO composite with high peroxymonosulfate utilization efficiency

A high-performance, durable, low-cost, and environmentally friendly catalyst is highly desired in advanced oxidation processes (AOPs) for water treatment. Considering the activity of Mn(Ⅲ) and the superior catalytic properties of reduced graphene oxide (rGO) in peroxymonosulfate (PMS) activation, rGO-modified MnOOH nanowires (MnOOH-rGO) were fabricated by a hydrothermal method for phenol degradation. The results showed that the composite synthesized at 120 °C with 1 wt% rGO dopant exhibited the best performance for phenol degradation. Nearly 100% of the phenol was removed by MnOOH-rGO within 30 min, which is higher than the removal rate of pure MnOOH (70%). The effects of catalyst dosages, PMS concentration, pH, temperature, and anions (Cl-, NO3-, HPO42-and HCO3-) on phenol degradation were investigated. The removal rate of chemical oxygen demand (COD) reached 26.4%, with a low molar ratio of PMS to phenol at 5:1 and a high PMS utilization efficiency (PUE) of 88.8%. The phenol removal rate remained more than 90% after five recycle with less than 0.1 mg L-1 leakage of manganese ions. Together with the results of radical quenching experiments, X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance spectroscopy (EPR), electron transfer and 1O2 were proved to dominate the activation process. During the direct electrons transfer process, the electrons transfer from the phenol to PMS by using the Mn(Ⅲ) as the mediate with a stoichiometric ratio between PMS and phenol at 1:2, which mainly contributed to the high PUE. This work provides new insight into a high-performance Mn(Ⅲ) based catalyst on PMS activation with high PUE, good reusability, and environmentally friendly for removing organic pollutants.

Efficient degradation of norfloxacin using a novel biochar-supported CuO/Fe3O4 combined with peroxydisulfate: Insights into enhanced contribution of nonradical pathway

Nonradical persulfate oxidation techniques have evolved as a new contaminated water treatment approach due to its great tolerance to water matrixes. The catalysts of CuO-based composites have received much attention in that aside from SO₄^•-/^•OH radicals, the nonradicals of singlet oxygen (¹O₂) can be also generated during persulfate activation via CuO. However, the issues regarding particles aggregation and metal leaching from the catalysts during the decontamination process remain to be addressed, which could have a remarkable impact on the catalytic degradation of organic pollutants. Accordingly in the present study, a novel biochar-supported bimetallic Fe₃O₄-CuO catalyst (CuFeBC) was facilely developed to activate peroxodisulfate (PDS) for the degradation of norfloxacin (NOR) in aqueous solution. The results showed CuFeBC has a superior stability against metal ions Cu/Fe leaching, and NOR (30 mg L^-1) was degraded at 94.5% within 180 min in the presence of CuFeBC (0.5 g L^-1) and PDS (6 mM) in pH 8.5. The scavenging of reactive oxygen species and electron spin resonance analysis revealed that ¹O₂ dominated the degradation of NOR. Compared with pristine CuO-Fe₃O₄, the interaction between biochar substrate and metal particles could significantly enhance the contribution of the nonradical pathway to NOR degradation from 49.6% to 84.7%. Biochar substrate could efficiently reduce the leaching of metal species from the catalyst, thereby maintaining excellent catalytic activity and lasting reusability of the catalyst. These findings could enlighten new insights into fine-tuning radical/nonradical processes from CuO-based catalysts for the efficient remediation of organic contaminants in polluted water.

Phthalate esters: occurrence, toxicity, bioremediation, and advanced oxidation processes

Phthalic acid esters are emerging pollutants, commonly used as plasticizers that are categorized as hazardous endocrine-disrupting chemicals (EDCs). A rise in anthropogenic activities leads to an increase in phthalate concentration in the environment which leads to various adverse environmental effects and health issues in humans and other aquatic organisms. This paper gives an overview of the research related to phthalate ester contamination and degradation methods by conducting a bibliometric analysis with VOS Viewer. Ecotoxicity analysis requires an understanding of the current status of phthalate pollution, health impacts, exposure routes, and their sources. This review covers five toxic phthalates, occurrences in the aquatic environment, toxicity studies, biodegradation studies, and degradation pathways. It highlights the various advanced oxidation processes like photocatalysis, Fenton processes, ozonation, sonolysis, and modified AOPs used for phthalate removal from the environment.