Employing electro-peroxone process for degradation of Acid Red 88 in aqueous environment by Central Composite Design: A new kinetic study and energy consumption

Development of a 10-litre pilot scale micro-nano bubble (MNB)-enhanced photocatalytic system for wastewater treatment

A 10-litre pilot scale micro-nano bubble (MNB)-enhanced photocatalytic degradation system was developed using ZnO as the photocatalyst and salicylic acid (SA) as the model pollutant. The effectiveness of the MNB/ZnO/UV system was systematically compared with those of MNB, UV, MNB/UV, MNB/ZnO and ZnO/UV degradation systems. The effects of process parameters, including catalyst dosage, pollutant concentration, air-intake rate, pH and salt content on the degradation of SA, were comprehensively investigated. Optimum performance was obtained at neutral conditions with a catalyst dosage of 0.3 g/L and an air-intake rate of 0.1 L/min. For the degradation of SA, a kinetic constant of 0.04126/min was achieved in the MNB/ZnO/UV system, which is 4.5 times greater than that obtained in the conventional ZnO/UV system. The substantial increase in the degradation rate can be attributed to that the air MNB not only enhanced the gas-liquid mass transfer efficiency but also elevated the concentration of dissolved oxygen. A 10-litre pilot scale MNB/ZnO/UV system was successfully applied to the purification of lake water and river water, demonstrating great application potential for wastewater treatment.

Integration of RCA-Based DNA Nanoscaffold with Target Triggered RNA-Cleaving DNAzyme for Sensitive Detection of miRNA21

Cascaded amplification showed promising potential for detection of trace target miRNAs in molecular diagnosis and prevention of many diseases. In this study, miRNA21 was chosen as the target, and rolling circle amplification (RCA)-based DNA nanoscaffold was integrated with target triggered RNA-cleaving DNAzyme for sensitive detection of miRNA21. That is, the H1 probe was bound with the long-chain product of RCA to self-assemble into DNA nanoscaffold. Target miRNA21 triggered the hybridization chain reaction (HCR) located on the nanoscaffold, and led to rapid proximity of DNAzyme fragments modified at both ends of the H2 probe, which realized the cyclic cleavage of self-quenching substrate probe efficiently, and the fluorescence signal was restored. The results demonstrated that the proposed assay was sensitive, 0.76 pM of miRNA21 can be detected. The proposed assay was specific; only one-base mismatched miRNA21 can be effectively recognized, other nucleic acid sequence and the serum matrix did not cause any interference. The proposed assay was accurate; recoveries from 82.1 to 115.0% can be obtained in the spiked fetal bovine serum (FBS). The flexible and programmable characteristics of DNA nanoscaffold and DNAzyme provide a confident and robust strategy for more sensitive nucleic acid detection, and can be developed to be a universal sensing platform for detecting other miRNAs just needing modification on the corresponding sequence of H1 probe in HCR.

Deep eutectic solvent-based ferrofluid for highly efficient preconcentration and determination of metronidazole by vortex-assisted liquid-phase microextraction under experimental design optimization

To determine metronidazole in water samples, we developed an environmentally friendly, efficient, and straightforward ferrofluid-based liquid-liquid microextraction sample pretreatment technique. It is coupled with a high-performance liquid chromatography-ultraviolet analytical technique known for its sensitivity, speed, and precision. The magnetic separation of metronidazole-containing ferrofluid from the matrix was effortlessly achieved through the application of an external magnetic field, eliminating the need for centrifugation. Response surface optimization was employed to systematically determine the key experimental parameters influencing extraction efficiency, including pH, NaCl concentration, ferrofluid volume, and vortex duration. With a low detection limit (0.116 ng mL-1), a broad linear range between 0.5 and 700 ng mL-1 was achieved at optimal conditions. Additionally, acceptable spiking recoveries (94.3-97.3 %) and RSD values (≤3.7 %) for intra- and inter-day precision were attained in water samples. In conclusion, the effectiveness of the vortex and ferrofluid combination, along with the convenience of collection and elimination of the need for centrifugation, bestows a highly valuable technique for determining metronidazole in water samples.

3D electro-Fenton augmented with iron-biochar particle electrodes derived from waste iron bottle caps and sugarcane bagasse for the remediation of sodium dodecyl sulphate

The present work demonstrates a novel strategy of synthesizing iron-biochar (Fe@BCSB) composite made with the waste iron bottle cap and sugar cane bagasse for implementation in the three-dimensional electro-Fenton (3DEF) process. The catalytic ability of the Fe@BCSB composite was explored to remediate the sodium dodecyl sulphate (SDS) surfactant from wastewater at neutral pH. At the optimum operating condition of Fe@BCSB dose of 1.0 g L-1, current density of 4.66 mA cm-2, and Na2SO4 dose of 50 mM, nearly 92.7 ± 3.1% of 20 mg L-1 of SDS abatement was attained during 120 min of electrolysis time. Moreover, the Fe@BCSB showed significant recyclability up to six cycles. Besides, other organics were successfully treated with more than 85% abatement efficiency in the proposed Fe@BCSB-supported 3DEF process. The total operating cost obtained during SDS treatment was around 0.31 US$ m-3 of wastewater. The phytotoxicity test revealed the positive impact of the 3DEF-treated effluent on the germination of the Vigna radiata. The electron paramagnetic resonance conveyed •OH as the prevailing reactive species for the oxidation of SDS in the 3DEF process. Further, about 81.3 ± 3.8% of SDS and 53.7 ± 4.1% of mineralization efficacy were acquired from the real institutional sewage.

Fabrication and optimization of febuxostat-loaded chitosan nanocarriers for better pharmacokinetics profile

The current research was planned to enhance the bioavailability of hydrophobic drug after oral administration through the development of a nanoparticle drug delivery system (DDS). Therefore, febuxostat-loaded chitosan nanoparticles (FLC NPs) were prepared using a modified ionic gelation method and optimized the reaction conditions through the design of experiments. Design expert software was used to check the desirability of the central composite design and the interactive effects of the independent variables (chitosan concentration, ratio of chitosan to linker, and pH of the medium) on the response variables (size distribution, zeta potential, polydispersity index (PDI), and entrapment efficiency (EE)) of FLC NPs. All ingredients of the optimized formulation (formulation Q) were compatible with each other as evident from FTIR, PXRD, and TGA studies, and displayed 234.7 nm particle size, 0.158 PDI, 25.8 mV zeta potential, and 76.9 % EE. TEM, SEM, and AFM exhibited a smooth, dense, and uniform structure without any visible pores in the structure of FLC NPs. The in vitro and in vivo drug release studies described a sustained release pattern of febuxostat and increased relative bioavailability by 286.63 %. Considering these findings, this chitosan nanoparticle DDS can further be used for improving the EE and bioavailability of hydrophobic drugs.

Process Optimization and Equilibrium, Thermodynamic, and Kinetic Modeling of Toxic Congo Red Dye Adsorption from Aqueous Solutions Using a Copper Ferrite Nanocomposite Adsorbent

In the present investigation of copper ferrite, a CuFe2O4 nanocomposite adsorbent was synthesized using the sol-gel method, and its relevance in the adsorptive elimination of the toxic Congo red (CR) aqueous phase was examined. A variety of structural methods were used to analyze the CuFe2O4 nanocomposite; the as-synthesized nanocomposite had agglomerated clusters with a porous, irregular, rough surface that could be seen using FE-SEM, and it also contained carbon (23.47%), oxygen (44.31%), copper (10.21%), and iron (22.01%) in its elemental composition by weight. Experiments were designed to achieve the most optimized system through the utilization of a central composite design (CCD). The highest uptake of CR dye at equilibrium occurred when the initial pH value was 5.5, the adsorbate concentration was 125 mg/L, and the adsorbent dosage was 3.5 g/L. Kinetic studies were conducted, and they showed that the adsorption process followed a pseudo-second-order (PSO) model (regression coefficient, R2 = 0.9998), suggesting a chemisorption mechanism, and the overall reaction rate was governed by both the film and pore diffusion of adsorbate molecules. The process through which dye molecules were taken up onto the particle surface revealed interactions involving electrostatic forces, hydrogen bonding, and pore filling. According to isotherm studies, the equilibrium data exhibited strong agreement with the Langmuir model (R2 = 0.9989), demonstrating a maximum monolayer adsorption capacity (qmax) of 64.72 mg/g at pH 6 and 302 K. Considering the obtained negative ΔG and positive ΔHads and ΔSads values across all tested temperatures in the thermodynamic investigations, it was confirmed that the adsorption process was characterized as endothermic, spontaneous, and feasible, with an increased level of randomness. The CuFe2O4 adsorbent developed in this study is anticipated to find extensive application in effluent treatment, owing to its excellent reusability and remarkable capability to effectively remove CR in comparison to other adsorbents.

Treatment of synthetic textile wastewater containing Acid Red 182 by electro-Peroxone process using RSM

The Azo dyes are primarily utilized in textile industries. Treatment of textile wastewater because of the presence of recalcitrant dyes using conventional processes is greatly challenging and ineffective. So far, no experimental work has been conducted on the decolorization of Acid Red 182 (AR182) in aqueous media. Hence, in this novel experimental work, the treatment of AR182 from the Azo dyes family was explored using the electro-Peroxone (EP) process. For the optimization of operating factors, including AR182 concentration, pH, applied current, and O3 flowrate in the decolorization of AR182, Central Composite Design (CCD) was utilized. The statistical optimization presented a highly satisfactory determination coefficient value and a satisfactory second-order model. The expected optimum conditions by the experimental design were as the following: AR182 concentration at 483.12 mg.L-1, applied current at 0.627,113 A, pH at 8.18284 and O3 flowrate at 1.13548 L min-1. The current density is directly proportional to dye removal. However, increasing the amount of applied current beyond a critical value has a contradictory impact on dye removal performance. The dye removal performance in both acidic and highly alkaline environments was negligible. Hence, ascertaining the optimum pH value and conduction of the experiment at that point is critical. At optimum points, the decolorization performance in predicted and experimental conditions for AR182 were 99 and 98.5%, respectively. The outcomes of this work clearly substantiated that the EP can be successfully utilized for the decolorization of AR182 in textile wastewater.

Use of Chrysosporium/carbon nanotubes for preconcentration of ultra-trace cadmium levels from various samples after extensive studies on its adsorption properties

Carbon nanotubes were used to immobilize Chrysosporium fungus for building an adequate adsorbent to be used as an desirable sorbent for preconcentration and measurement of cadmium ultra-trace levels in various samples. After characterization, the potential of Chrysosporium/carbon nanotubes for the sorption of Cd(II) ions was scrutinized by the aid of central composite design, and comprehensive studies of sorption equilibrium, kinetics and thermodynamic aspects were accomplished. Then, the composite was utilized for preconcentration of ultra-trace cadmium levels, by a mini-column packed with Chrysosporium/carbon nanotubes, before its determination with ICP-OES. The outcomes vouchsafed that (i) Chrysosporium/carbon nanotube has a high tendency for selective and rapid sorption of cadmium ion, at pH 6.1, and (ii) kinetic, equilibrium, and thermodynamic studies showed a high affinity of the Chrysosporium/carbon nanotubes for cadmium ion. Also, the outcomes displayed that cadmium can quantitatively be sorbed at a flow speed lesser than 7.0 mL/min and a 1.0 M HCl solution (3.0 mL) was sufficient to desorbe the analyte. Eventually, preconcentration and measurement of Cd(II) in different foods and waters were successfully accomplished with good accuracy, high precision (RSDs ≤5.65%), and low limit of detection (0.015 μg/L).