Recent developments in MOF and MOF based composite as potential adsorbents for removal of aqueous environmental contaminants

Four three-dimensional rare earth metal - organic framework fluorescent sensor for efficient detection of gentamicin sulfate and Fe3

Excessive use of gentamicin sulfate can cause severe nephrotoxicity and ototoxicity, abnormal levels of Fe3+ intake can also cause serious damage to body. Therefore, establishing a fast and accurate detection method for the above-mentioned substances is of great significance. However, traditional detection methods such as high-performance liquid chromatography still have certain problems such as high cost and complex operation. Fluorescent MOFs are favored by analysts due to their high specific surface area, high porosity, adjustable pore size, and good stability. In this paper, we have synthesized four rare earth MOFs based on the pyridinecarboxylic acid ligand (H2L), which are [Eu(L)1/2H2O]n, [Gd(L)1/2H2O]n, [Sm(L)1/2H2O]n, [Y(L)3/2H2O·DMF]n. The structures of four MOFs were confirmed by single crystal X-ray diffraction, which proved that MOF-1, MOF-2 and MOF-3 were isostructural, and all the four MOFs were three-dimensional structures. In the fluorescence test, gentamicin sulfate and Fe3+ can cause significant fluorescence quenching of MOF-1 and MOF-4 respectively, and show good selectivity and anti-interference performance, as well as low detection limit and wide detection range. This work may provide a possibility for the detection of gentamicin sulfate and iron ions in complex environments.

Adsorption efficiency of chitosan/clinoptilolite (CS/CZ) composite for effective removal of Cd+2 and Cr+6 ions from wastewater effluents of dairy cattle farms

The wastewater effluent is responsible for the major ecological impact of the dairy sectors. To avoid the negative consequences of heavy metal pollution on the ecosystem, creative, affordable, and efficient treatment methods are now required before the effluent flows into the surrounding area. This study was aimed at assessing the effectiveness of three different adsorbents for Cd+2 and Cr+6 ions from wastewater effluents of dairy farms, including chitosan (CS), clinoptilolite zeolite (CZ), and chitosan/clinoptilolite zeolite (CS/CZ) composite. The adsorption kinetics of the CS/CZ composite were established using the effects of the key variables (pH, agitation speed, adsorbent concentrations, and contact durations). The removal (%) and adsorption capacities, qe (mg/g), were calculated using the data from the adsorption kinetics. Wastewater samples (n = 60) were collected from the wastewater effluents of five farms. Cd+2 and Cr+6 ion concentrations in all collected samples were determined. Following the CS/CZ composite creation, it was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (X-RD), and Fourier-transform infrared spectrum (FT-IR). The CS/CZ composite had an adsorption capacity of 92.4 and 96.5 mg/g for both Cd+2 and Cr+6 ions at a concentration of 2.0 g/100 ml, respectively, while the CZ adsorption capacities for the two ions were 87.5 mg/g and 61.0 mg/g, respectively, at 4.0 g/100 ml concentration. The CS was achieved at 55.56 mg/g and 33.3 mg/g, respectively, at the same concentration. The efficiency of heavy metal removal was enhanced by increasing adsorbent concentration, agitation speed, and contact duration. Using CS/CZ composite at 2.0 g/100 ml concentration, 180 min of contact time, and 300 rpm agitation speed, the greatest removal efficiencies for Cd+2 and Cr+6 ions (96.43 and 98.75%, respectively) were demonstrated.

Efficient adsorptive removal of used drugs during the COVID-19 pandemic from contaminated water by magnetic graphene oxide/MIL-88 metal-organic framework/alginate hydrogel beads

Currently, the presence of drugs used in the COVID-19 pandemic in water bodies is worrisome due to their high toxicity, which necessitates their critical removal by developing highly efficient adsorbents. Hence, in this study, alginate hydrogel beads of magnetic graphene oxide@MIL-88 metal-organic framework (GO@Fe3O4@MIL-88@Alg) were prepared for the first time and then utilized as a new absorption system for the removal of COVID-19 drugs such as doxycycline (DOX), hydroxychloroquine (HCQ), naproxen (NAP), and dipyrone (DIP) from aqueous solutions by batch adsorption manner. The effects of different experimental factors, such as adsorbent dosage, contact time, pH, drug concentration, temperature, ionic strength, presence of an external magnetic field (EMF), and magnet distance from the adsorption flask were optimized for the removal of COVID-19 drugs. The adsorption equilibrium isotherm proved that the adsorption process of DOX, HCQ, NAP, and DIP drugs on GO@Fe3O4@MIL-88@Alg hydrogel beads conformed to the Langmuir model and followed the pseudo-second-order adsorption kinetics. The maximum adsorption capacities of DOX, HCQ, NAP, and DIP drugs obtained for GO@Fe3O4@MIL-88@Alg hydrogel beads with the Langmuir model were 131.57, 79.92, 55.55, and 49.26 mg/g at 298 K, respectively. The thermodynamic study suggested a spontaneous endothermic adsorption process. Also, the conclusion from this study confirmed the validity of GO@Fe3O4@MIL-88@Alg hydrogel beads for excellent removal of COVID-19 drugs from water samples. It was also found that the GO@Fe3O4@MIL-88@Alg hydrogel beads could be reused with satisfactory removal efficiency in six cycles. Based on the study, the GO@Fe3O4@MIL-88@Alg hydrogel beads could be considered a sustainable, simple, economical, environmentally friendly absorption system for the removal of pharmaceutical contaminants from water.

Recent trends in wastewater treatment by using metal-organic frameworks (MOFs) and their composites: A critical view-point

Respecting the basic need of clean and safe water on earth for every individual, it is necessary to take auspicious steps for waste-water treatment. Recently, metal-organic frameworks (MOFs) are considered as promising material because of their intrinsic features including the porosity and high surface area. Further, structural tunability of MOFs by following the principles of reticular chemistry, the MOFs can be functionalized for the high adsorption performance as well as adsorptive removal of target materials. However, there are still some major concerns associated with MOFs limiting their commercialization as promising adsorbents for waste-water treatment. The cost, toxicity and regenerability are the major issues to be addressed for MOFs to get insightful results. In this article, we have concise the current strategies to enhance the adsorption capacity of MOFs during the water-treatment for the removal of toxic dyes, pharmaceuticals, and heavy metals. Further, we have also discussed the role of metallic nodes, linkers and associated functional groups for effective removal of toxic water pollutants. In addition to conformist overview, we have critically analyzed the MOFs as adsorbents in terms of toxicity, cost and regenerability. These factors are utmost important to address before commercialization of MOFs as adsorbents for water-treatment. Finally, some future perspectives are discussed to give directions for potential research.

A novel magnetic Ti-MOF/chitosan composite for efficient adsorption of Pb(II) from aqueous solutions: Synthesis and investigation

In this investigation, a composite material comprising Ti-MOF and chitosan, denoted as BD-MOF(Ti)@CS/Fe3O4, was successfully designed for the efficient adsorption of Pb(II) from aqueous solutions. A comprehensive array of characterization techniques, including SEM, XRD, BET, FT-IR, and XPS, were meticulously employed to scrutinize the structural attributes and morphological features of the Pb(II) adsorbent. Notably, the material exhibits adaptability to a broad pH range, with adsorption efficiency reaching 99 % between pH 3 and 6. Kinetic studies reveal that the adsorption process of Pb(II) by BD-MOF(Ti)@CS/Fe3O4 adheres closely to a pseudo-second-order kinetic model. Impressively, within a short duration of 40 min, the adsorption efficiency can reach 85 %. Furthermore, the adsorption isotherm aligns with the Hill isotherm model, signifying cooperative adsorption. This observation underscores the synergistic interplay among the functional groups on the surface of BD-MOF(Ti)@CS/Fe3O4 in capturing Pb(II). As per the Hill model, the theoretical maximum capacity was an impressive 944.9 mg/g. Thermodynamic assessments suggested that the adsorption process was spontaneous, entropy increasing and exothermic. Even in the presence of various interfering ions, BD-MOF(Ti)@CS/Fe3O4 exhibited robust adsorption performance, thereby affirming its utility in complex environments. Moreover, the material demonstrates noteworthy reusability, sustaining effective Pb(II) removal across five consecutive cycles in aqueous solutions.

On the adsorption characteristics and mechanism of methylene blue by ball mill modified biochar

In this study, modified biochar (BRB) was prepared from rice straw by ball milling technique and used for the adsorption of methylene blue (MB) in wastewater. The BRB was characterized by SEM, FTIR and XPS, and the adsorption model and Box-Behnken design were used to optimize the five influencing factors. The results showed that the ball milling technique could increase the content of functional groups (-OH, C=C and C-O, etc.) and aromatic structures on the surface of biochar, thus facilitating the removal of MB. The isotherm model was consistent with the Langmuir adsorption model (R2 = 0.947) and the maximum adsorption capacity was 50.27 mg/g. The adsorption kinetics was consistent with the pseudo-second-order kinetic model (R2 = 1) and the adsorption rate was mainly controlled by chemisorption. The thermodynamic model confirmed that the adsorption process was a spontaneous heat absorption reaction. The maximum adsorption efficiency was 99.78% under the optimal conditions (40℃, pH 8, reaction time = 90 min, dosing amount = 0.1 mg), and the adsorption efficiency could be improved by increasing the pH and BRB dosing amount. The surface functional groups and crystal structure properties of BRB were the main determinants of adsorption, and it was clarified that physical adsorption, electrostatic attraction and π-π interaction were the main mechanisms for the adsorption of MB by BRB. The main mechanisms were clarified. Therefore, BRB is an economic, efficient and green adsorption material with good potential for the removal of dye pollutants in the aqueous environment.

A review on artificial water channels incorporated polyamide membranes for water purification: Transport mechanisms and performance

While thin-film composite (TFC) polyamide (PA) membranes are advanced for removing salts and trace organic contaminants (TrOCs) from water, TFC PA membranes encounter a water permeance-selectivity trade-off due to PA layer structural characteristics. Drawing inspiration from the excellent water permeance and solute rejection of natural biological channels, the development of analogous artificial water channels (AWCs) in TFC PA membranes (abbreviated as AWCM) promises to achieve superior mass transfer efficiency, enabling breaking the upper bound of water permeance and selectivity. Herein, we first discussed the types and structural characteristics of AWCs, followed by summarizing the methods for constructing AWCM. We discussed whether the AWCs acted as the primary mass transfer channels in AWCM and emphasized the important role of the AWCs in water transport and ion/TrOCs rejection. We thoroughly summarized the molecular-level mechanisms and structure-performance relationship of water molecules, ions, and TrOCs transport in the confined nanospace of AWCs, which laid the foundation for illustrating the enhanced water permeance and salt/TrOCs selectivity of AWCM. Finally, we discussed the challenges encountered in the field of AWCM and proposed future perspectives for practical applications. This review is expected to offer guidance for understanding the transport mechanisms of AWCM and developing next-generation membrane for effective water treatment.

Schiff base-functionalized metal-organic frameworks as an efficient adsorbent for the decontamination of heavy metal ions in water

Adsorptive removal of heavy metal ions from water is an energy- and cost-effective water decontamination technology. Schiff base functionalities can be incorporated into the pore cages of metal-organic frameworks (MOFs) via direct synthesis, post-synthetic modification, and composite formation. Such incorporation can efficiently enhance the interactions between the MOF adsorbent and target heavy metal ions to promote the selective adsorption of the latter. Accordingly, Schiff base-functionalized MOFs have great potential to selectively remove a particular metal ion from the aqueous solutions in the presence of coexisting (interfering) metal ions through the binding sites within their pore cages. Schiff base-functionalized MOFs can bind divalent metal ions (e.g., Pb(II), Co(II), Cu(II), Cd (II), and Hg (II)) more strongly than trivalent metal ions (e.g., Cr(III)). The adsorption capacity range of Schiff base-functionalized MOFs for divalent ions is thus much more broad (22.4-713 mg g-1) than that of trivalent metal ions (118-127 mg g-1). To evaluate the adsorption performance between different adsorbents, the two parameters (i.e., adsorption capacity and partition coefficient (PC)) are derived and used for comparison. Further, the possible interactions between the Schiff base sites and the target heavy metal ions are discussed to help understand the associated removal mechanisms. This review delivers actionable knowledge for developing Schiff-base functionalized MOFs toward the adsorptive removal of heavy metal ions in water in line with their performance evaluation and associated removal mechanisms. Finally, this review highlights the challenges and forthcoming research and development needs of Schiff base-functionalized MOFs for diverse fields of operations.

Phosphate adsorption by metal organic frameworks: Insights from a systematic review, meta-analysis, and predictive modelling with artificial neural networks

This comprehensive study analysed 55 articles published between 2011 and 2022 on the use of metal organic frameworks (MOFs) for phosphate adsorption. The study found that the performance of MOFs in phosphate adsorption is influenced by various factors such as the type of MOF, synthesis method, modification/alteration, and operational conditions (initial concentration, adsorbent dose, pH, contact time, and temperature). Most of the MOFs have a wide range of theoretical maximum adsorption capacity for phosphate, but their long-term use in phosphorus recovery may be limited due to the adsorption mechanisms being dominated by inner sphere complexation. The study employed machine learning to construct artificial neural network (ANN) models for predicting phosphate adsorption capacity based on input features from operation and synthesis procedures. The initial phosphate concentration was the most important input from the operational features, while the modulator agent was consistently relevant during MOF synthesis. The models showed strong fitting for most MOF types recorded for the study, such as UIO-66, MIL-100, ZIF-8, Al-MOFs, La-MOFs, and Ce-MOFs. Overall, this study provides valuable insights for the design of MOF adsorbents for phosphate adsorption and offers guidance for future research in this area.

Nanoscale designing of metal organic framework moieties as efficient tools for environmental decontamination

Environmental pollutants, being a major and detrimental component of the ecological imbalance, need to be controlled. Serious health issues can get intensified due to contaminants present in the air, water, and soil. Accurate and rapid monitoring of environmental pollutants is imperative for the detoxification of the environment and hence living beings. Metal-organic frameworks (MOFs) are a class of porous and highly diverse adsorbent materials with tunable surface area and diverse functionality. Similarly, the conversion of MOFs into nanoscale regime leads to the formation of nanometal-organic frameworks (NMOFs) with increased selectivity, sensitivity, detection ability, and portability. The present review majorly focuses on a variety of synthetic methods including the ex situ and in situ synthesis of MOF nanocomposites and direct synthesis of NMOFs. Furthermore, a variety of applications such as nanoabsorbent, nanocatalysts, and nanosensors for different dyes, antibiotics, toxic ions, gases, pesticides, etc., are described along with illustrations. An initiative is depicted hereby using nanostructures of MOFs to decontaminate hazardous environmental toxicants.

Adsorption of heavy metals on natural zeolites: A review

Water pollution has jeopardized human health, and a safe supply of drinking water has been recognized as a worldwide issue. The increase in the accumulation of heavy metals in water from different sources has led to the search for efficient and environmentally friendly treatment methods and materials for their removal. Natural zeolites are promising materials for removing heavy metals from different sources contaminating the water. It is important to know the structure, chemistry, and performance of the removal of heavy metals from water, of the natural zeolites to design water treatment processes. This review focuses on critical analyses of the application of distinct natural zeolites for the adsorption of heavy metals from water, specifically, arsenic (As(III), As(V)), cadmium (Cd(II)), chromium (Cr(III), Cr(VI)), lead (Pb(II)), mercury(Hg(II)) and nickel (Ni(II)). The reported results of heavy-metal removal by natural zeolites are summarized, and the chemical modification of natural zeolites by acid/base/salt reagent, surfactants, and metallic reagents has been analyzed, compared, and described. Furthermore, the adsorption/desorption capacity, systems, operating parameters, isotherms, and kinetics for natural zeolites were described and compared. According to the analysis, clinoptilolite is the most applied natural zeolite to remove heavy metals. It is effective in removing As, Cd, Cr, Pb, Hg, and Ni. Additionally, an interesting fact is a variation between the natural zeolites from different geological origins regarding the sorption properties and capacities for heavy metals suggesting that natural zeolites from different regions of the world are unique.

Hierarchical Mesoporous Metal-Organic Frameworks with Boric Acid Sites on the Inner Surface of Small Mesopores for the Extraction of Nucleotides in Human Plasma Samples

In this work, a boronate affinity-functionalized hierarchical mesoporous metal-organic framework adsorbent with boronate sites only in the small mesopore has been structured based on UiO-66@Fe₃O₄. The introduction of large mesopores in the adsorbent can promote the diffusion of small cis-diol-containing compounds (cis-diols) into small mesopore channels, and the removal of the adsorption sites on the external surface of materials and in large mesopores can enhance the size-exclusion effect of the adsorbent. In addition, the adsorbent has faster adsorption kinetics and excellent selectivity to small cis-diols. Finally, a magnetic dispersive solid-phase extraction coupled with high-performance liquid chromatography was established for the enrichment and detection of nucleotides in plasma. Four nucleotides achieve the recoveries from 93.25 to 118.79%, the limits of detection from 0.35 to 1.26 ng·mL^-1, and the intra-day and inter-day relative standard deviations of less than 10.2%. In conclusion, this method can be directly used for the detection of small cis-diol targets in complex biological samples without protein precipitation prior to the extraction.

Facile solvent-free radical polymerization to prepare itaconate-functionalized hydrochar for efficient sorption of methylene blue and Pb(II)

An itaconate-functionalized hydrochar (IFHC) was prepared from one-step solvent-free radical copolymerization of bamboo hydrochar, itaconic acid, ammonium persulphate and sodium hydroxide in solvent-free environment, and was employed to absorb methylene blue (MB) and Pb(II) from wastewater. Characterizations show IFHC has rich carboxylate and tends to adsorb cationic contaminants. The largest adsorbed quantities of MB and Pb(II) by IFHC are up to 1036 and 291.8 mg·g^-1 at 298 K respectively as per the Langmuir isotherm. Sorption of MB and Pb(II) onto IFHC can be expressed well by Langmuir isotherm and pseudo-2nd-order kinetics equations. The high sorption performance depends on the rich carboxylate, which can adsorb MB/Pb(II) through an electrostatic interaction/inner-surface complexation mechanism. The sorptive capacity of regenerated IFHC decreased below 10% after 5 desorption-resorption cycles. Thus, the solvent-free free radical copolymerization is an environmentally-friendly strategy to synthesize novel efficient sorbents that can clean cationic contaminants from wastewater.

Highly defective copper-based metal-organic frameworks for the efficient adsorption and detection of organophosphorus pesticides: An experimental and computational investigation

Organophosphorus pesticide (OP) residues pose a serious threat to human health, motivating the search for novel adsorbents and detection methods. Herein, defective copper-based metal organic frameworks (Cu-MOFs) were synthesized by the reaction of Cu²⁺ ions and 1,3,5-benzenetricarboxylate linkers in the presence of acetic acid. As the amount of acetic acid increased, the crystallization kinetics and morphology of the Cu-MOFs changed, leading to mesoporous Cu-MOFs with many large surface pores (defects). Adsorption studies of OPs revealed the defective Cu-MOFs showed faster pesticide adsorption kinetics and higher pesticide adsorption capacities. Density functional theory calculations showed that pesticide adsorption in the Cu-MOFs was mainly electrostatic. A dispersive solid phase extraction method was developed based on a defective Cu-MOF-6 for rapidly extracting pesticides from food samples. The method allowed pesticide detection over a wide linear concentration range, low limits of detection (0.0067-0.0164 µg L^-1) and good recoveries in pesticide-spiked samples (81.03-109.55%).

Olive mill wastewater from a liquid biological waste to a carbon/oxocalcium composite for selective and efficient removal of methylene blue and paracetamol from aqueous solution

In this study, a Carbon/Oxocalcium was prepared from olive mill wastewater and successfully applied to the removal of paracetamol and methylene blue (MB) from an aqueous medium. The optimized composite (0.3 % CaO) is rich in anionic sites, porous and has a specific surface area of about 1383 m².g^-1. Adsorption tests showed significant adsorption capacities up to 1141 mg.g^-1. The adsorption of MB and paracetamol is well described by the Redlich-Peterson and Dubinin-Radushkevich isotherm, respectively. Moreover, the adsorption kinetics fitted to pseudo-second order. The π -π interactions, hydrogen bonds and electrostatic interactions were responsible for the adsorption of paracetamol and MB substrates. This work develops by a single, easy and simple action a new effective and selective material for the removal of emerging pollutants, a new method for the development of more stable carbon composites and a cost-effective method for the valorization of olive mill wastewater.

Facile Conversion of Polystyrene Waste into an Efficient Sorbent for Water Purification

In this work, we convert a plastic waste, i.e., polystyrene (PS), into a sorbent by a simple sulfonation process. The sulfonation time was optimized and the structures of the resulting sulfonated polystyrene (SPS) was characterized by field emission scanning electron microscopy, energy-dispersive X-ray and contact angle tests. The results showed that the sulfonation time of 7 h can introduce abundant sulfonic groups and preserve the self-standing structure. Additionally, the SPS has a three-dimensional porous structure and hydrophilic surface because of the presence of numerous sulfonic groups, which could serve as effective binding sites for immobilizing varying pollutants. Furthermore, as a proof-of-concept, the adsorption performance of the SPS foams was evaluated using three pollutants, namely Pb²⁺, lysozyme and methylene blue. The adsorption isotherms were fitted by the Langmuir and Freundlich models, while the kinetics of the adsorption processes were analyzed using the pseudo-first-order, pseudo-second-order and intraparticle diffusion equations. It was found that the adsorption isotherms of Pb²⁺ and lysozyme can be better described by the Langmuir model, leading to maximum equilibrium adsorption uptakes of 10.5 and 15.7 mg g⁻¹ for the adsorption of Pb²⁺ and lysozyme, respectively. Importantly, the pollutant-saturated SPS is readily regenerated by acid washing, and the recovered sorbents exhibit outstanding cyclic performance. The abundant availability of feedstock, facile preparation and regeneration processes render the SPS foams a promising sorbent for practical applications.

Three novel Co(II)-based MOFs: Syntheses, structural diversity, and adsorption properties

In this paper, three new cobalt-based metal organic frameworks (MOFs) with different topologies, namely {[Co(HL)(tib)(H2O)]·2H2O}n (1), [Co3(L)2(bibp)4(H2O)2]n (2) and [Co2(L)(bip)(μ3-OH)]n (3) (H3L = 3-(3,5-dicarboxylphenoxy)-6-carboxylpyridine, tib = 1,3,5-tirs(1-imidazolyl)benzene, bibp = 4,4'-bis(imidazolyl)biphenyl,...