Alginate-modified biochar derived from rice husk waste for improvement uptake performance of lead in wastewater

Mechanistic investigation of Pb2+ adsorption on biochar modified with sodium alginate composite zeolitic imidazolate framework-8

For the serious situation of heavy metal pollution, the use of cheap, clean, and efficient biochar to immobilize heavy metals is a good treatment method. In this paper, SA@ZIF-8/BC was prepared for the adsorption of Pb2+ in solution using sodium alginate (SA) and zeolitic imidazolate framework-8 (ZIF-8) modified corn cob biochar. The results showed that the specific surface area of modified biochar was greatly improved, with good adsorption capacity for Pb2+, strong anti-interference ability, and good economy. At the optimal adsorption pH of 5, the adsorption model of Pb2+ by SA@ZIF-8/BC was more consistent with the pseudo-second-order kinetic model and Langmuir isotherm model. This indicates that the adsorption of Pb2+ by SA@ZIF-8/BC is chemisorption and monolayer adsorption. The maximum adsorption of modified biochar was 300 mg g-1, which was 2.38 times higher than that of before modified BC (126 mg g-1). The shift in binding energy of functional groups before and after adsorption of SA@ZIF-8/BC was studied by XPS, and it was found that hydroxyl and carboxyl groups played an important role in the adsorption of Pb2+. It was demonstrated that this novel adsorbent can be effectively used for the treatment of Pb pollution in wastewater.

Mitigation of caffeine micropollutants in wastewater through Ag-doped ZnO photocatalyst: mechanism and environmental impacts

Micropollutants, such as caffeine (M-CF), pose a significant threat to ecosystems and human health through water and food sources. The utilization of metal oxide-based photocatalysts has proven to be an effective treatment method for the removal of organic pollutants. This study explores the efficacy of Ag-doped ZnO (Ag/ZnO) for removing M-CF from wastewater. The characterization of Ag/ZnO underscores the crucial role of band gap energy in the photocatalytic degradation process. This parameter influences the separation of electrons and holes (e-/h+) and the generation of reactive radicals. Under solar light, Ag/ZnO demonstrated markedly superior photocatalytic activity, achieving an impressive degradation efficiency of approximately 93.4%, in stark contrast to the 53.2% occurred by ZnO. Moreover, Ag/ZnO exhibited a remarkable degradation efficiency of M-CF in wastewater, reaching 83.5%. A key advantage of Ag/ZnO lies in its potential for recovery and reuse in subsequent treatments, contributing to a reduction in operational costs for industrial wastewater treatment. Impressively, even after five cycles, Ag/ZnO maintained a noteworthy photodegradation rate of M-CF at 78.6%. These results strongly suggest that Ag/ZnO presents a promising solution for the removal of micropollutants in wastewater, with potential scalability for industrial and large-scale applications.

The application of P-modified biochar in wastewater remediation: A state-of-the-art review

Phosphorus modified biochar (P-BC) is an effective adsorbent for wastewater remediation, which has attracted widespread attention due to its low cost, vast source, unique surface structure, and abundant functional groups. However, there is currently no comprehensive analysis and review of P-BC in wastewater remediation. In this study, a detailed introduction is given to the synthesis method of P-BC, as well as the effects of pyrolysis temperature and residence time on physical and chemical properties and adsorption performance of the material. Meanwhile, a comprehensive investigation and evaluation were conducted on the different biomass types and phosphorus sources used to synthesize P-BC. This article also systematically compared the adsorption efficiency differences between P-BC and raw biochar, and summarized the adsorption mechanism of P-BC in removing pollutants from wastewater. In addition, the effects of P-BC composite with other materials (element co-doping, polysaccharide stabilizers, microbial loading, etc.) on physical and chemical properties and pollutant adsorption capacity of the materials were investigated. Some emerging applications of P-BC were also introduced, including supercapacitors, CO2 adsorbents, carbon sequestration, soil heavy metal remediation, and soil fertility improvement. Finally, some valuable suggestions and prospects were proposed for the future research direction of P-BC to achieve the goal of multiple utilization.

Alginate-encapsulated biochar as an effective soil ameliorant for reducing Pb phytoavailability to lettuce (Lactuca sativa L.)

The alginate-biochar formulation for metal removal from aquatic environments has been widely tried but its use for lowering phytoavailability of metals in the soil-crop continuum is limited. Biochar has been increasingly used as a soil amendment due to its potential for soil carbon sequestration and sorption capacity. Handling of powdery biochar as a soil top-dressing material is, however, cumbersome and vulnerable to loss by water and wind. In this experiment, biochar powder, which was pyrolyzed from oak trees, was encapsulated into beads with alginate, which is a naturally occurring polysaccharide found in brown algae. Both batch and pot experiments were conducted to examine the effects of the alginate-encapsulated biochar beads (BB), as compared to its original biochar powdery form (BP), on the Pb adsorption capacity and phytoavailability of soil Pb to lettuce (Lactuca sativa L.). The BB treatment improved reactivity about six times due to a higher surface area (287 m2 g-1) and five times due to a higher cation exchange capacity (50 cmolc kg-1) as compared to the BP treatment. The maximum sorption capacity of Pb was increased to 152 from 81 mg g-1 because of surface chemosorption. Adsorption of Pb onto BB followed multiple first-order kinetics and comprised fast and slow steps. More than 60% of the Pb was adsorbed in the fast step, i.e., within 3 h. Also, the BB treatment, up to the 5% level (w/w), increased soil pH from 5.4 to 6.5 and lowered the phytoavailable fraction of Pb in soil from 5.7 to 0.3 mg kg-1. The Pb concentrations in lettuce cultivated at 5% for the BP and BB treatments were similar but 63 and 66% lower, respectively, than those of the control soil. The results showed that the encapsulation of biochar with alginate enhanced adsorption by the biochar.

Sugarcane bagasse-derived granular activated carbon hybridized with ash in bio-based alginate/gelatin polymer matrix for methylene blue adsorption

Sugarcane bagasse (SCB) and sugarcane bagasse ash (SCB-ash) are major agricultural residues from sugar processing industries in Thailand. In this study, SCB-derived activated carbon (SCBAC) with the optimum surface area of 489 m2/g was prepared by steam activation at 900 °C for 1 h. Hybrid granular activated carbons (GACs) were successfully developed by mixing SCBAC with bio-based polymers, alginate and gelatin, at the weight ratio of 3:1 for methylene blue (MB) adsorption. SCB-ash, which was additionally mixed in the GACs, could significantly increase compressive strength of the GACs, but decrease their surface areas and MB adsorption efficiencies. An existence of gelatin up to 30 wt% in the polymer matrix of the GACs showed a slight increase in swelling degree and iodine number, but could not enhance bead strength and MB adsorption efficiency due to its relatively lower bulk density and specific surface area. Maximum MB adsorption capacities of the GACs were found at 290-403 mg/g under this study's experimental condition. MB adsorption efficiencies at above 90 % with no deformation of all of the selected SCB hybrid GACs were finally confirmed after seven consecutive adsorption-desorption cycles using a simple regeneration with ethanol.

Effect of the magnetic core in alginate/gum composite on adsorption of divalent copper, cadmium, and lead ions in the aqueous system

The change of composition of an adsorbent material has been widely used as a method to increase its adsorption capacity, particularly concerning adsorbents made of polysaccharides. Introducing magnetic adsorbents into contaminated water treatment systems is a highly promising strategy, as it promotes the metal ions removal from water. Considering this, gum Arabic (GA) was associated with alginate (Alg), when magnetite nanoparticles were present or absent, to produce beads that were utilised to take up Cu(II), Cd(II), and Pb(II) from aqueous solution. After a complete characterisation (for which Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and swelling were used), the adsorption properties were established using batch and column tests. The magnetic beads (MAlg/GA) demonstrated improved adsorption in comparison with the beads made without magnetite (Alg/GA) under the same conditions. In normal adsorption conditions (pH 6.0, 25 °C, 2.5 g L-1 of adsorbent dosage), the highest uptake capacities recorded for the MAlg/GA beads were: for Cu(II), 1.33 mmol g-1; Cd(II), 1.59 mmol g-1; and for Pb(II), 1.43 mmol g-1. The pseudo-second-order kinetics and Langmuir isotherm models provided good fits for the adsorption of these metals. Overall, ion exchange and physical forces led to the uptake of these metals by both Alg/GA and MAlg/GA; moreover, the functional groups on the beads played crucial roles as binding sites. Additionally, it was observed that flow rates of >2 mL min-1 did not produce noticeable changes in uptake levels over the same flow period. It was found that the efficient eluting agent was HNO3 (0.2 M). In some cases, the metals were not removed fully from the used beads during the first five cycles of regeneration and reuse. The results of this investigation show that these beads are efficient adsorbents for the removal of metal ions from spiked well water samples.

Adsorption and photodegradation of micropollutant in wastewater by photocatalyst TiO2/rice husk biochar

With the acceleration of global industrialization, organic pollutants have become a threat to ecological safety and human health. This work prepared TiO2/rice husk biochar (TiO2/BC) for removal of bisphenol A (BA) micropollutant in wastewater. Experiment results revealed a low BA removal efficiency by TiO2/BC was observed at 34.5% under the dark environment. However, the removal rate of BA by UV light-assisted TiO2/BC significantly increased to 97.6% in 1 h. The results also demonstrated that the removal performance of BA using TiO2/BC was 2.1times higher than that of commercial TiO2 (46.4%). Besides, the removal efficiency of BA by reused TiO2/BC after eight cycles slightly decreased by 12.8%, demonstrating the excellent properties of the prepared composite. TiO2/BC also exhibited high removal efficiency of BA (over 89%) from the synthetic wastewater sample, indicating the potential utilization of composite for removing BA in wastewater. This work provides a new way to turn biomass waste into useful material and effective method to remove micropollutant BA.

Removal ibuprofen from aqueous solution by a noval Al-modified biochar

With the increase of organic emissions in production and human life, the pollution control of organic is now an urgent problem in the environmental field. In this study, hydrothermal carbonization rice husk-loaded Al-modified biochar (Al-BC) was synthesized, and the results of scanning electron microscopy could be used to determine that Al oxide composite was loaded on the surface of the material. The specific surface area was 57.049 m2 g-1, pore volume was 0.254 cm3 g-1, and average pore diameter was 8.922 nm for BC and 109.617 m2 g-1, 0.215 cm3 g-1, and 3.969 nm for Al-BC, respectively. The control effects of these two adsorption materials on organic pollutant ibuprofen (IBU) under different pH conditions were also investigated. The research results show that the adsorption capacity of Al-BC (30.24-1.48 mg g-1) is better than BC (19.98-0.92 mg g-1) at pH from 2 to 11. Solution pH plays a crucial role in IBU adsorption from organic solution. The Langmuir fitting results show that at pH = 7, the saturated adsorption capacity of IBU on BC could reach up to 18.68 mg g-1; the adsorption capacity on Al-BC was 60.49 mg g-1. The thermodynamic parameters indicate that the adsorption is spontaneous, endothermic, and increased disorder. The adsorption material prepared in this study could provide a reference for organic pollution control in water.

Sustainable application of rice-waste for fuels and valuable chemicals-a mini review

The global annual production of rice is over 750 million tons, and generates a huge amount of biomass waste, such as straw, husk, and bran, making rice waste an ideal feedstock for biomass conversion industries. This review focuses on the current progress in the transformation of rice waste into valuable products, including biochar, (liquid and gaseous) biofuels, valuable chemicals (sugars, furan derivatives, organic acids, and aromatic hydrocarbons), and carbon/silicon-based catalysts and catalyst supports. The challenges and future prospectives are highlighted to guide future studies in rice waste valorization for sustainable production of fuels and chemicals.

Magnesium oxide nanoparticles modified biochar derived from tea wastes for enhanced adsorption of o-chlorophenol from industrial wastewater

In this work, magnesium oxide nanoparticles supported biochar derived from tea wastes (MgO@TBC) was prepared as an effective adsorbent for removing hazardous o-chlorophenol (o-CP) from industrial wastewater. The surface area, porous structure, surface functional groups and surface charge of tea waste biochar (TBC) significantly enhanced after the modification process. The best uptake performance of o-CP was found at pH = 6.5 and 0.1 g of MgO@TBC adsorbent. According to the adsorption isotherm, the adsorption of o-CP onto MgO@TBC followed the Langmuir model with a maximum uptake capacity of 128.7 mg/g, which was 26.5% higher than TBC (94.6 mg/g). MgO@TBC could be reused for eight cycles with a high o-CP uptake performance (over 60%). Besides, it also exhibited good removal performance of o-CP from industrial wastewater with a removal rate of 81.7%. The adsorption behaviors of o-CP onto MgO@TBC are discussed based on the experimental results. This work may provide information to prepare an effective adsorbent for removing hazardous organic contaminants in wastewater.

Porous adsorbent derived from acid activation of food waste biochar: A sustainable approach for novel removal chlorophenol in wastewater

In this study, porous biochar (PBC) was prepared by acid activation of biochar derived from food waste (FWBC) and used as a suitable approach for the removal of 4-chlorophenol (CP) in wastewater. The characterization of PBC and the influent of different experimental conditions are determined. After the acid activation process, the surface area, porosity, and functional groups of PBC were developed. The removal performances of CP (1 mg/L) by PBC and FWBC were archived at 97.8 and 82.1%, respectively. Adsorption kinetics and isotherms of CP were followed by the second-order and Langmuir models, respectively. The maximum capacities of CP uptake onto mono-layer of FWBC and PBC based on the Langmuir model were determined at 79.8 and 108.7 mg/g, respectively. Besides, PBC could remove more than 89% CP from wastewater within 45 min of reaction time and it is suitable to reuse 8 times with over 60% adsorption efficiency of CP. In addition, the adsorption mechanism and environmental impact were discussed in detail. This work could bring a sustainable approach to the treatment of CP in wastewater as well as the management of food waste in Vietnam.

Improved Cr (VI) adsorption performance in wastewater and groundwater by synthesized magnetic adsorbent derived from Fe3O4 loaded corn straw biochar

This work developed an easy method to utilize corn straw (CS) waste for sustainable development and reduce the volume of waste volume as well as bring value-added. The magnetic adsorbent was prepared by loading Fe₃O₄ onto biochar derived from corn straw (Fe@CSBC), then used for capturing Cr (VI) in groundwater and wastewater samples. The characterization of adsorbents showed that Fe3O4 was successfully loaded on corn straw biochar (CSBC) and contributed to the improvement of the surface area, and surface functional groups like Fe-O, Fe-OOH, CO, and O-H. The presence of iron oxide was further confirmed by XPS and XRD analysis and a magnetization value of 35.6 emu/g was obtained for Fe@CSBC. The highest uptake capacity of Cr (VI) onto Fe@CSBC and CSBC by monolayer were 138.8 and 90.6 mg/g, respectively. By applying magnetic adsorbent Fe@CSBC for the treatment of groundwater and wastewater samples, the chromium could be removed up to 90.3 and 72.6%, respectively. The remaining efficiency of Cr (VI) was found to be 84.5% after four times reused Fe@CSBC, demonstrating the great recyclable ability of the adsorbent. In addition, several interactions between Cr (VI) and Fe@CSBC like ion exchange, complexation, and reduction reaction were discussed in the proposed adsorption mechanism. This study brings an efficient method to turn corn straw biomass into an effective magnetic adsorbent with high adsorption performance and good reusability of Cr (VI) in groundwater as well as in wastewater.

Adsorption Characteristics of Dimethylated Arsenicals on Iron Oxide-Modified Rice Husk Biochar

In this study, the adsorption characteristics of dimethylated arsenicals to rice husk biochar (BC) and Fe/biochar composite (FeBC) were assessed through isothermal adsorption experiments and X-ray absorption spectroscopy analysis. The maximal adsorption capacities (q_m) of inorganic arsenate, calculated using the Langmuir isotherm equation, were 1.28 and 6.32 mg/g for BC and FeBC, respectively. Moreover, dimethylated arsenicals did not adsorb to BC at all, and in the case of FeBC, q_m values of dimethylarsinic acid (DMA(V)), dimethylmonothioarsinic acid (DMMTA(V)), and dimethyldithioarsinic acid (DMDTA(V)) were calculated to be 7.08, 0.43, and 0.28 mg/g, respectively. This was due to the formation of iron oxide (i.e., two-line ferrihydrite) on the surface of BC. Linear combination fitting using As K-edge X-ray absorption near edge structure spectra confirmed that all chemical forms of dimethylated arsenicals adsorbed on the two-line ferrihydrite were DMA(V). Thus, FeBC could retain highly mobile and toxic arsenicals such as DMMTA(V) and DMDTA(V)) in the environment, and transform them into DMA(V) with relatively low toxicity.