WO3/rGO nanocomposite-based sensor for the detection and degradation of 4-Chlorophenol

Preparation of W-N-C single atom catalyst and Cu3(HHTP)2 metal-organic framework dual-decorated graphene nanoplatelet flexible electrode arrays for the rapid detection of carbendazim in vegetables

It is highly desirable to develop a low-cost and rapid detection method for trace levels of carbendazim fungicide residues, which would be beneficial for improving human health and mitigating environmental issues. Herein, isolated single tungsten atoms were implanted onto well-organized metal-organic framework (MOF)-derived N-doped carbons to form W-N-C single-site heterojunctions with ultrahigh electrocatalytic activity. The coupling of W-N-C with Cu3(HHTP)2, an electronically conductive MOF with a large surface area and porous structure, exhibited enhanced electrocatalytic performance for the oxidation of carbendazim (CBZ) when they were used for decorating graphene nanoplatelet flexible electrode arrays fabricated via template-assisted scalable filtration. A wide linear range (3.0 nM-50 μM) with an ultra-low detection limit of 0.97 nM and fast response was achieved for CBZ analysis. Moreover, the sensing platform has been utilised to monitor CBZ levels in vegetable samples with satisfactory recovery rates of 97.2-102% and a low relative standard deviation of 1.9%.

Development of tungsten trioxide nano-flakes intercalated on tannic acid-functionalized reduced graphene oxide for flexible acebutolol sensors

Acebutolol (ACE) is commonly used to treat hypertension and high blood pressure. Large doses of ACE can have adverse effects with potentially life-threatening consequences. It is, therefore, essential to develop a simple, low-cost, reliable, and reproducible device for detecting ACE in biofluids. This study explores the potential of unique two-dimensional nano-flakes, such as tungsten trioxide (WO3). Graphene oxide (GO) typically exhibits lower electrical conductivity than pristine graphene due to the presence of oxygen-containing functional groups that interfere with the π-conjugated structure. Functionalizing GO with tannic acid (TA) can partially reinstate the π-conjugation and limit the amount of oxygen, resulting in enhanced electrical conductivity. Ultrasonic techniques were utilized to create WO3 NFs@TA-rGO, and a range of spectroscopic and microscopic methods were applied to examine the formation of the resulting WO3 NFs@TA-rGO nanocomposites. Under optimal conditions, modified sensors resulted in lower limits of detection (0.0055 μM) and good sensitivity (0.40 μA μM-1 cm-2). They also exhibited a broad linear range spanning from 0.009 to 568.6 μM. Fabricated sensors have significant anti-interference properties with high specificity and excellent storage stability (RSD = 4.3 %), reproducibility (RSD = 3.9 %), and repeatability (RSD = 3.3 %). Ultimately, the sensor's efficacy was confirmed through the successful detection of ACE in biological samples (with recoveries ranging from 99.1 to 99.6 %). Lastly, this study highlights the substantial potential of ACE detection and extends its applications in biomedical diagnostics and pharmaceutical research.

Adsorptive removal of benzene and toluene from aqueous solutions by oxygen-functionalized multi-walled carbon nanotubes derived from rice husk waste: A comparative study

One of the current directions for sustainable development is to use waste resources to create materials that reduce environmental pollution. In this study, multi-walled carbon nanotubes (MWCNT) and their oxygen-functionalized forms (HNO₃/H₂SO₄-oxidized MWCNT, NaOCl-oxidized MWCNT, and H₂O₂-oxidized MWCNT) were first synthesized from activated carbon (AC) derived from rice husk waste. A comprehensive comparison of the morphological and structural properties of these materials was conducted using FT-IR, BET, XRD, SEM, TEM, TGA, Raman spectroscopy, and surface charge analysis. The morphology study suggests that the synthesized MWCNTs have an average outer and inner diameter of about 40 and 20 nm, respectively. Additionally, the NaOCl-oxidized MWCNT possesses the largest interspaces between nanotubes, while the HNO₃/H₂SO₄-oxidized CNT has the most oxygen-functional groups, including -COOH, (Ar)-OH, and C-OH. The adsorption capacities of these materials were also compared for the removal of benzene and toluene. Experimental results have shown that while porosity is the primary factor governing the benzene and toluene adsorption onto AC, functionalization degree and surface chemical characteristics are the determining factors in the adsorption capacity of the as-prepared MWCNTs. The adsorption capacity of these aromatic compounds in an aqueous solution increases in the following order: AC < MWCNT < HNO₃/H₂SO₄-oxidized MWCNT < H₂O₂-oxidized MWCNT < NaOCl-oxidized MWCNT, and in all cases, toluene is more readily adsorbed than benzene under similar adsorption conditions. Wherein the uptake of both pollutants by the prepared adsorbents in this study is best described by the Langmuir isotherm and obeys the pseudo-second-order kinetic model. The adsorption mechanism was discussed in a detailed manner.

Graphene and gold nanoparticle-based bionanocomposite for the voltammetric determination of bisphenol A in (micro)plastics

The monitoring of endocrine disruptors in the environment is one of the main strategies in the investigation of potential risks associated with exposure to these chemicals. Bisphenol A is one of the most prevalent endocrine-disrupting compounds and is prone to leaching out from polycarbonate plastic in both freshwater and marine environments. Additionally, microplastics also can leach out bisphenol A during their fragmentation in the water environment. In the quest for a highly sensitive sensor to determine bisphenol A in different matrices, an innovative bionanocomposite material has been achieved. This material is composed of gold nanoparticles and graphene, and was synthesized using a green approach that utilized guava (Psidium guajava) extract for reduction, stabilization, and dispersion purposes. Transmission electron microscopy images revealed well-spread gold nanoparticles with an average diameter of 31 nm on laminated graphene sheets in the composite material. An electrochemical sensor was developed by depositing the bionanocomposite onto a glassy carbon surface, which displayed remarkable responsiveness towards bisphenol A. Experimental conditions such as the amount of graphene, extract: water ratio of bionanocomposite and pH of the supporting electrolyte were optimized to improve the electrochemical performance. The modified electrode displayed a marked improvement in current responses for the oxidation of bisphenol A as compared to the uncovered glassy carbon electrode. A calibration plot was established for bisphenol A in 0.1 mol L^-1 Britton-Robinson buffer (pH 4.0), and the detection limit was determined to equal to 15.0 nmol L^-1. Recovery data from 92 to 109% were obtained in (micro)plastics samples using the electrochemical sensor and were compared with UV-vis spectrometry, demonstrating its successful application with accurate responses.