Ultrasound assisted mixed azo dye adsorption by chitosan–graphene oxide nanocomposite

Incorporation of copper ion promoted adsorption of anionic dye (Acid Yellow 36) by acrolein-crosslinked polyethyleneimine/chitosan hydrogel: Adsorption, dynamics, and mechanisms

In this study, a novel adsorbent, A-PEI/CS-Cu2+, was developed by crosslinking polyethyleneimine/chitosan hydrogel with acrolein and loading it with copper ions. The adsorption process of A-PEI/CS-Cu2+ on the anionic dye acid yellow 36 (AY36) was investigated by kinetic, isothermal and thermodynamic modeling. It was noteworthy that A-PEI/CS-Cu2+ exhibited rapid adsorption with a 90 % removal rate achieved within just 5 min, which was much faster than the adsorption rate of A-PEI/CS without load of copper ions and showed its potential for rapid adsorption applications. The maximum adsorption capacity for AY36 could reach up to 3114 mg g-1. In addition, the high concentration of saline wastewater was found to have almost no effect on the adsorption reaction in the salt effect test experiment. In five desorption-regeneration cycle experiments, the sample exhibited good recyclability and regeneration performance. The driving force of the adsorption process mainly originated from the electrostatic interaction, hydrogen bonding, and intermolecular interaction, in which the addition of copper ions led to the enhancement of the electrostatic interaction and chelation between A-PEI/CS-Cu2+ and AY36. Overall, the findings suggest the excellent potential of A-PEI/CS-Cu2+ for rapid and efficient adsorption, as well as its suitability for practical applications in wastewater treatment.

Ultrasonic treatment of dye chemicals in wastewater: A review

The existence of pollutants, such as toxic organic dye chemicals, in water and wastewater raises concerns as they are inadequately eliminated through conventional water and wastewater treatment methods, including physicochemical and biological processes. Ultrasonic treatment has emerged as an advanced treatment process that has been widely applied to the decomposition of recalcitrant organic contaminants. Ultrasonic treatment has several advantages, including easy operation, sustainability, non-secondary pollutant production, and saving energy. This review examines the elimination of dye chemicals and categorizes them into cationic and anionic dyes based on the existing literature. The objectives include (i) analyzing the primary factors (water quality and ultrasonic conditions) that influence the sonodegradation of dye chemicals and their byproducts during ultrasonication, (ii) assessing the impact of the different sonocatalysts and combined systems (with ozone and ultraviolet) on sonodegradation, and (iii) exploring the characteristics-based removal mechanisms of dyes. In addition, this review proposes areas for future research on ultrasonic treatment of dye chemicals in water and wastewater.

Wastewater purification from Rhodamine B and Gemifeloxacine by graphene oxide/pectin/ferrite nanocomposite: A novel molecular dynamics simulation for experimental contaminants removing

In this study, the synthesized nanocomposite was evaluated novel graphene oxide/pectin/ferrite (GOPF) adsorbent to the adsorption of Rhodamine B (RhB) and Gemifloxacin (GEM) from wastewater. Theoretical studies were carried out using quantum simulation via the Forcite module in Material Studio 2017. The simulation results demonstrated RhB and GEM adsorption over other dyes and drugs. The synthesized nanocomposite was identified by BET, TGA, FT-IR, FE-SEM, XRD, VSM, and EDS. The nanocomposite's ability to effectively take RhB and GEM from an aqueous solution was checked by performing a series of experiments based on the effect of adsorbent dose, initial condensation, contact time, pH, and temperature. The nanocomposite kinetics follow a PSO. The Freundlich isotherm model was applied for maximum adsorption capacity of GEM (124.37 mg/g) and RhB (86.60 mg/g) on GOPF nanocomposite. According to the antibacterial activity test, the synthesized nanocomposite can kill bacteria 5 mm in diameter. Also, the anti-cancer test of nanocomposite was done with 75% viability in high concentrations of nanocomposite. Thus, GOPF application results are not only suitable for dyes but only satisfying for drugs. PRACTITIONER POINTS: GOPF nanocomposite was fabricated for adsorption dye and drug and characterized. The effect of different process parameters, pH, catalyst dosage, contact time, and temperature effect was surveyed. The MD simulation were investigated to adsorb various dyes and drugs. The equilibrium isotherm and adsorption kinetic follow from Freundlich and pseudo-second-order kinetics; GOPF nanocomposite was used for about six cycles. The antibacterial activity and anticancer test of GOPF nanocomposite were investigated by satisfying results.

Nanostructured Materials for Water Purification: Adsorption of Heavy Metal Ions and Organic Dyes

Chemical water pollution poses a threat to human beings and ecological systems. The purification of water to remove toxic organic and inorganic pollutants is essential for a safe society and a clean environment. Adsorption-based water treatment is considered one of the most effective and economic technologies designed to remove toxic substances. In this article, we review the recent progress in the field of nanostructured materials used for water purification, particularly those used for the adsorption of heavy metal ions and organic dyes. This review includes a range of nanostructured materials such as metal-based nanoparticles, polymer-based nanomaterials, carbon nanomaterials, bio-mass materials, and other types of nanostructured materials. Finally, the current challenges in the fields of adsorption of toxic materials using nanostructured materials are briefly discussed.

Graphene Oxide-Chitosan Aerogels: Synthesis, Characterization, and Use as Adsorbent Material for Water Contaminants

Porous aerogels, formed by subjecting precursor hydrogels using a freeze-drying process, are certainly one of the most studied and synthetized soft materials, thanks to their important features such as elasticity, swelling behavior, softness, and micro and nanosized pores, which guarantee their applicability in various fields. Typically, these systems are synthetized working with natural or synthetic polymers, but in the last years great interest has been given to proper formulated aerogels able to combine polymeric structures with other moieties such as graphene or graphene oxide. This working strategy can be pivotal in many cases to tune important properties of the final system such as toughness, porosity, elasticity, electrical conductivity, or responsive behavior. In this work we propose the synthesis of chitosan graphene oxide aerogels obtained through self-assembly of graphene oxide sheets and chitosan chains. These three-dimensional systems were chemically characterized with IR and XRD technique and their inner structure was investigated through the scanning electron microscopy (SEM). Moreover, we mechanically characterized the material through dynamic mechanical analysis, showing the stability of these systems. Finally, the adsorption ability of these soft materials has been demonstrated using model molecules to simulate water contaminants showing the efficacy of those graphene-based systems even for the removal of anionic dyes. Complete removal of contaminants was obtained at low concentration of dyes in solution (100 mg/L), while with a higher amount of pollutant in the solution (350 mg/L) high sorption capacity (q > 200 mg/g) was observed.

Chitosan-based hybrid materials for adsorptive removal of dyes and underlying interaction mechanisms

Environmental pollution by dyes molecules has become a subject of intensive research in recent years due to their hazardous effects on human health, organisms, and animals. Effective treatment and removal of dye molecules from the environmental matrices and water sources are of supreme concern. The deployment of cheap, safe, green, sustainable, and eco-friendly materials to remove these pollutants from water is the main challenge during the last decades. Chitosan and its derivatives/composites, as a cheap, easily available, and environmentally friendly sorbent, have attracted increasing attention for the removal of dye molecules. This review article focuses on the application of chitosan and chitosan-based smart adsorbents for the removal of dyes. Recent methods for the preparation of chitosan-based composites and their application in the removal of dyes are discussed. Moreover, the possible mechanisms for the interaction of chitosan and chitosan-based adsorbents with dyes molecules were evaluated. Finally, future prospects of using chitosan as an adsorbent for the removal of dye molecules are directed.

Polymer Nanocomposites for Photocatalytic Degradation and Photoinduced Utilizations of Azo-Dyes

Specially designed polymer nanocomposites can photo-catalytically degrade azo dyes in wastewater and textile effluents, among which TiO2-based nanocomposites are outstanding and extensively explored. Other nanocomposites based on natural polymers (i.e., chitosan and kaolin) and the oxides of Al, Au, B, Bi, Fe, Li, and Zr are commonly used. These nanocomposites have better photocatalytic efficiency than pure TiO2 through two considerations: (i) reducing the hole/electron recombination rate by stabilizing the excited electron in the conducting band, which can be achieved in TiO2-nanocomposites with graphene, graphene oxide, hexagonal boron nitride (h-BN), metal nanoparticles, or doping; (ii) decreasing the band energy of semiconductors by forming nanocomposites between TiO2 and other oxides or conducting polymers. Increasing the absorbance efficiency by forming special nanocomposites also increases photocatalytic performance. The photo-induced isomerization is exploited in biological systems, such as artificial muscles, and in technical fields such as memory storage and liquid crystal display. Heteroaryl azo dyes show remarkable shifts in photo-induced isomerization, which can be applied in biological and technical fields in place of azo dyes. The self-assembly methods can be employed to synthesize azo-dye polymer nanocomposites via three types of interactions: electrostatic interactions, London forces or dipole/dipole interactions between azo dyes, and photo alignments.

Treatment of malachite green dye containing solution using bio-degradable Sodium alginate/NaOH treated activated sugarcane baggsse charcoal beads: Batch, optimization using response surface methodology and continuous fixed bed column study

In this study, carbonized material was produced using sodium hydroxide treated Sugar cane bagasse (SB), and synthesized materials ware used to prepare Sodium Alginate/SBAC composite beads which were further used as an adsorbent to remove malachite green dye (MG) present in water. Physiochemical characteristics of composite beads were analyzed using FTIR, SEM, TGA, and BET. Adsorption equilibrium data showed excellent fit to the Freundlich model (R² = 0.994) than to the Langmuir model (R² = 0.925). Adsorption kinetics study indicated that the MG removal process would be better described by the pseudo-second-order kinetic model. The thermodynamic study suggested the spontaneous and endothermic nature of MG adsorption. By using response surface methodology, the optimum conditions for MG adsorption on composite beads were found to be 115.43 min, 0.3 g/L and pH 8 for contact time, adsorbent mass, and pH respectively and MG adsorption efficiency was 97.88%. The fixed-bed column data were evaluated using several kinetic models and among them, Thomas model showed the best agreement with investigation results. These results revealed that synthesized composite beads have a high affinity toward MG and it could be reasonable, eco-friendly adsorbent for dye removal from wastewater.

Adsorption of indigo carmine on functional chitosan and β-cyclodextrin/chitosan beads: Equilibrium, kinetics and mechanism studies

The present study was designed to produce novel cross-linked Chitosan and Chitosan/β-Cyclodextrin beads and study the adsorption of Indigo Carmine. Both adsorbents were characterized by SEM and FTIR techniques. Batch experiments were conducted in order to evaluate the effect of initial adsorbent's concentration, dye's initial concentration, initial pH and temperature. In all cases Chitosan/β-Cyclodextrin crosslinked beads exhibited higher removal efficiency of Indigo Carmine. Higher removal rates of Indigo Carmine were observed at low values of dye's initial concentration, pH and temperature, and high concentrations of adsorbent. The equilibrium adsorption data were a good fit for both Langmuir and Freundlich models and maximum adsorption capacity was 500.0 and 1000.0 mg_IC/g_adsorbent for Chitosan and Chitosan/β-Cyclodextrin crosslinked beads, respectively. Adsorption of Indigo Carmine was found to follow the pseudo-second order. The negative values of ΔG^o, ΔH^o and ΔS^o indicate that the adsorption process is exothermic, spontaneous and favorable at low temperatures.

Interfacial separation of concentrated dye mixtures from solution with environmentally compatible nitrogenous-silane nanoparticles modified with Helianthus annuus husk extract

The capacity of an adsorbent to bind and remove dye from solution greatly depends on the type of functionalization present on the nanoparticles surface, and its interaction with the dye molecules. Within this study, nitrogenous silane nanoparticles were hydrothermally synthesized resulting in the formation of rapid and highly efficient adsorbents for concentrated mixed dyes. The amorphous silane nanoparticles exhibited a monolayer based mechanism of mixed dye adsorption with removal capacities between 416.67 and 714.29 mg/g of adsorbent. Dye removal was predominantly due to the electrostatic attraction between the positively charged silane nanoparticles (13.22-8.20 mV) and the negatively charged dye molecules (-54.23 mV). Addition of H. annuus extract during synthesis resulted in three times the surface area and 10 times increased pore volume compared to the positive control. XPS analysis showed that silane treatments had various nitrogen containing functionalities at their surface responsible for binding dye. The weak colloidal stability of silane particles (13.22-8.20 mV) was disrupted following dye binding, resulting in their rapid coagulation and flocculation which facilitated the separation of bound dye molecules from solution. The suitability for environmental applications using these treatments was supported by a bacterial viability assay showing >90% cell viability in treated dye supernatants.

Removal of Cr(VI) by magnetic iron oxide nanoparticles synthesized from extracellular polymeric substances of chromium resistant acid-tolerant bacterium Lysinibacillus sphaericus RTA-01

BACKGROUND

Extracellular polymeric substances (EPS) from Cr(VI) resistant acid-tolerant biofilm forming bacterium (CrRAtBb) Lysinibacillus sphaericus RTA-01 was used for synthesis of magnetic iron oxide nanoparticles (MIONPs) in removal of Cr(VI).

METHODS

MIONPs synthesized in EPS matrix were characterized by UV-Vis, DLS, ATR-FTIR, XRD, FESEM, HRTEM and VSM. Primarily, the synthesis of MIONPs was established by the formation of black-colored precipitate through surface plasmon resonance (SPR) peak in between 330 and 450 nm.

RESULTS

The size of the spherical MIONPs with diameter range 13.75-106 nm was confirmed by DLS, XRD and FESEM analysis. HRTEM study confirmed the size of the MIONPs in the range of 10-65 nm. Moreover, the EDX and SAED confirmed the purity and polycrystalline nature of MIONPs. The ATR-FTIR peaks below 1000 cm-1 designated the synthesis of MIONPs. Also, the magnetic property of MIONPs was confirmed for separation from the aqueous solution. MIONPs were further checked for the adsorption of Cr(VI) with initial concentration range of 50-200 mg L-1. An adsorption isotherm and thermodynamic study were also carried out and the experimental data was best fitted in Langmuir isotherm model with maximum adsorption percent of 1052.63 mg g-1 of Cr(VI). Post interaction with Cr(VI), the surface characteristic of MIONPs in EPS matrix was evaluated by zeta potential, EDX, ATR-FTIR and XRD.

CONCLUSION

This study ascertained the adsorption of Cr(VI) over EPS stabilized MIONPs whereas the zeta potential and XRD analysis confirmed the presence of reduced Cr(IV) on the adsorbent surface.

Preparation of Graphene Oxide/Chitosan Pellets and Their Adsorption Properties for Congo Red

A facile and easily separated adsorbent, graphene oxide (GO) pellets wrapped by chitosan (GOP) were prepared. Batch adsorption studies were carried out to study the adsorption properties of congo red onto GOP by varying the experimental parameters such as the contact time, the initial concentration of congo red, the solution pH, the adsorbent dose, and the temperature. The kinetic studies showed that the adsorption data fitted a pseudo-second-order model well. The isotherm analysis showed that the adsorption data fitted the Freundlich model well. The adsorption mechanism was mainly attributed to electrostatic interactions, [Formula: see text]–[Formula: see text] stacking interaction, hydrogen bond, and van der Waals force. Thermodynamic studies indicated that the adsorption process was endothermic and spontaneous.

Optimization of dye adsorption capacity and mechanical strength of chitosan aerogels through crosslinking strategy and graphene oxide addition

Chitosan (CS) aerogels were prepared by freeze-drying as potential adsorbents for water purification, and the effect of the strategy of crosslinking was investigated by varying the amount of crosslinker (glutaraldehyde) and the sequence of steps for the preparation of the aerogel. Two procedures were compared, in which the crosslinking step was carried out before or after the freeze-drying of the starting CS solution. When crosslinking was postponed after the freeze-drying step, the adsorption capacity towards an anionic dye, such as indigo carmine, considerably increased (up to +45%), reaching values as high as 534.4 ± 30.5 mg g^-1. The same crosslinking strategy ensured a comparable improvement also in nanocomposite aerogels containing graphene oxide (GO), which was added to enhance the mechanical strength and provide adsorption capacity towards cationic dyes. Besides possessing good mechanical strength (compressive modulus higher than 1 MPa), the CS/GO aerogels were able to bind also cationic pollutants such as methylene blue. The maximum uptake capacity increased from 4.3 ± 1.6 to 168.6 ± 9.6 mg of cationic dye adsorbed per gram of adsorbent with respect to pristine CS aerogels.

A review on agro-industrial waste (AIW) derived adsorbents for water and wastewater treatment

There is a large amount of studies surrounding the usage of agro-industrial waste (AIW) for the adsorptions of organic pollutants (dyes) and inorganic pollutants (heavy metals) in water/wastewater. This method is normally treated as an alternative approach to the conventional water/wastewater treatment. However, there are some increasing interests for investigators to identify novel adsorption materials for pollutants removal. It is particularly noteworthy that most AIW wastes are not currently used at the original state, but modified in a variety of ways to reinforce the porosity and adsorption surface area of the material. Nanostructuring, activation, carbonization, and grafting are some common modification technologies of agricultural waste adsorbents. Besides, the characteristic, preparation and application of adsorbents from various industrial wastes, including natural materials and biosorbents, were summarized. Additionally, the challenges and perspectives for future researches of waste-derived adsorbents were studied. This review provides an important insight on using AIWs as precursor materials for preparing adsorbents in water/wastewater treatment.

Application of response surface methodology in physicochemical removal of dyes from wastewater: A critical review

Response surface methodology (RSM) is a powerful tool in designing the experiments and optimizing different environmental processes. However, when it comes to wastewater treatment and specifically dye-containing wastewater, two questions arise; "Is RSM being used correctly?" and "Are all capabilities of RSM being exploited properly?". The current review paper aims to answer these questions by scrutinizing different physicochemical processes that utilized RSM in dye removal. The literature that applied RSM to adsorption, advanced oxidation processes, coagulation/flocculation and electrocoagulation processes were critically reviewed in this paper. The common errors in applying RSM to physicochemical removal of dyes are identified and some suggestions are made for future studies.

Assessment on the decolourization of textile dye (Reactive Yellow) using Pseudomonas sp. immobilized on fly ash: Response surface methodology optimization and toxicity evaluation

This study focuses on the investigation of removal of textile dye (Reactive Yellow) by a combined approach of sorption integrated with biodegradation using low cost adsorbent fly ash immobilized with Pseudomonas sp. To ensure immobilization of bacterial species on treated fly ash, fly ash with immobilized bacterial cells was characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and fluorescence microscopy. Comparative batch studies were carried out using Pseudomonas sp, fly ash and immobilized Pseudomonas sp on flyash and were observed that immobilized Pseudomonas sp on flyash acted as better decolourizing agent. The optimized pH, temperature, and immobilized adsorbent dosage for highest percentage of dye removal were observed to be pH 6, 303 K, 1.2 g/L in all the cases. At optimum condition, the highest percentage of dye removal was found to be 88.51%, 92.62% and 98.72% for sorption (flyash), biodegradation (Pseudomonas sp) and integral approach (Pseudomonas sp on flyash) respectively. Optimization of operating parameters of textile dye decolourization was done by response surface methodology (RSM) using Design Expert 7 software. Phytotoxicity evaluation with Cicer arietinum revealed that seeds exposed to untreated dye effluents showed considerably lower growth, inhibited biochemical, and enzyme parameters with compared to those exposed to treated textile effluents. Thus this immobilized inexpensive technique could be used for removal of synthetic dyes present in textile wastewater.

Carbon composite lignin-based adsorbents for the adsorption of dyes

Carbon composite lignin-based adsorbent were prepared through hydrothermal method with glucose as carbon source, calcium lignosulfonate and triethylene tetramine as raw materials, respectively. The optimum synthesis conditions were determined by investigating the addition of carbon and triethylene tetramine. The adsorbent was used for the adsorption of azo dyes Congo red and Eriochrome blue black R, and the five factors affecting the adsorption were discussed, including pH of dyes, initial concentration, adsorption time, adsorption temperature and adsorbent dosage. The corresponding adsorption mechanism such as pseudo first order kinetics, pseudo second order kinetics, intraparticle diffusion, Langmuir adsorption isotherm, Freundlich isotherm, Temkin isotherm, Dubinin-Radushkevich adsorption isotherm, thermodynamics were also studied. When the dye concentration is 40 mg L^-1, Congo red and Eriochrome blue black R dye removal rates reach 99%. Moreover, the adsorption process of two kinds of dyes follow the pseudo second order kinetics and the Langmuir adsorption isotherm.

Development of a graphene oxide/chitosan nanocomposite for the removal of picric acid from aqueous solutions: Study of sorption parameters

The functionalization of graphene oxide (GO) with chitosan (Chi) has been investigated to prepare a nanocomposite material (GO-Chi) for the removal of picric acid from aqueous solutions. Materials were characterized by FT-IR, TGA, DTG, FESEM, EDX, XRD and BET. Batch experiments such as solution pH, amount of adsorbents, contact time, concentration of the picric acid and temperature were achieved to study sorption process. Kinetic studies were well described by pseudo-second-order kinetic model for both adsorbents. Isotherm studies showed that the Langmuir isotherm for GO and Freundlich and Halsey models for GO-Chi were found to best represent the measured sorption data. Negative ΔG° values for GO-Chi and positive ones for GO indicated the nature of spontaneous and unspontaneous, respectively for adsorption process. In addition, picric acid molecules can be desorbed from GO-Chi up to 80% at pH=9 and that the consumed GO-Chi could be reutilized up to 5th cycle of regeneration.