Brass wires with different surface wettability used for in-tube solid-phase microextraction

A functionalized glass fiber as the adsorbent for efficient analysis of endocrine disruptors in aqueous environments

Estrogens and bisphenols are typical endocrine disruptors (EDs) that pose a potential hazard to the human body due to their widespread presence in aqueous environments. In this study, a β-cyclodextrin porous crosslinked polymer (β-CD-PCP) was prepared in-situ on a glass fiber surface by a nucleophilic substitution reaction. An effective and sensitive solid phase microextraction method using functionalized glass fiber with β-CD-PCP coating as the adsorbent was established for the detection of 11 EDs in a water environment. The β-CD-PCP was in-situ prepared on a glass fiber surface by a nucleophilic substitution reaction. The β-CD-PCP successfully separated five estrogens (ESTs) and six bisphenols (BPs) through hydrophobic and π-π interactions. The conditions affecting extraction were optimized. Under the optimized conditions, the ESTs obtained a high enrichment effect (1795-2328), low limits of detection (0.047 µg L-1) and a good linearity range (0.2-15.0 µg L-1). Furthermore, the spiked recoveries of analyte ESTs in aqueous environments were between 82.9-115.7 %. The results indicated that the prepared functionalized glass fibers exhibited good adsorption properties, and the established analytical method was reliable for monitoring trace ESTs and BPs in aqueous environments.

Modified stainless steel wires with superwettability for highly efficient in-tube solid-phase microextraction

Construction of different surface wettability is meaningful for the interaction between the sorbent surface and target components. In the current study, four kinds of stainless-steel wires (SSWs) with different hydrophobic/hydrophilic property were prepared and used as the absorbents to enrich the target compounds with different polarity. Comparative extraction of six non-polar polycyclic aromatic hydrocarbons (PAHs) and six polar estrogens was carried out by in-tube solid phase microextraction (IT-SPME). The results showed that two SSWs with the superhydrophobic surfaces exhibited high extraction capacity to the non-polar PAHs with the superior enrichment factor (EF) in the range of 29-672 and 57-744, respectively. In contrast, the superhydrophilic SSWs demonstrated higher enrichment efficiency for the polar estrogens than other hydrophobic SSWs. On the basis of optimized conditions, a validated analysis method was established using six PAHs as model analytes for IT-SPME-HPLC. Acceptable linear ranges (0.5-10 μg L^-1) and low detection limits (0.0056-0.32 μg L^-1) were achieved using the superhydrophobic wire modified by perfluorooctyl trichlorosilane (FOTS). The relative recoveries spiked at 2, 5 and 10 μg L^-1 in the lake water samples were in the range of 81.5%-113.7%. The relative standard deviation (RSD) of intraday (≤0.8%, n = 3) and interday (≤5.3%, n = 3) tests demonstrated the good extraction repeatability for the same extraction tube. Satisfactory repeatability for the preparation of extraction tubes (n = 3) was also obtained with the RSD values in the range of 3.6%-8.0%.

In-Tube Solid-Phase Microextraction Directly Coupled to Mass Spectrometric Systems: A Review

Since it was introduced in 1997, in-tube solid-phase microextraction (in-tube SPME), which uses a capillary column as extraction device, has been continuously developed as online microextraction coupled to LC systems (in-tube SPME-LC). In the last decade, new couplings have been evaluated on the basis of state-of-the-art LC instruments, including direct coupling of in-tube SPME to MS/MS systems, without chromatographic separation, for high-throughput analysis. In-tube SPME coupling to MS/MS has been possible thanks to the selectivity of capillary column coatings and MS/MS systems (SRM mode). Different types of capillary columns (wall-coated open-tubular, porous-layer open-tubular, sorbent-packed, porous monolithic rods, or fiber-packed) with selective stationary phases have been developed to increase the sorption capacity and selectivity of in-tube SPME. This review focuses on the in-tube SPME principle, extraction configurations, current advances in direct coupling to MS/MS systems, experimental parameters, coatings, and applications in different areas (food, biological, clinical, and environmental areas) over the last years.

Robust Super-Amphiphobic Titanium Surface for Liquid/Liquid Mini Separations

Super-amphiphobic surface with low robustness is not suitable for practical application due to its weak mechanical strength. In this work, an in-site growth of micro-/nanoscale flower-like TiO2 on the surface of a titanium mesh was successfully fabricated through hydrothermal synthesis, followed by chemical modification with low-surface-energy heptadecafluoro-1,1,2,2-tetrahydrodecyl trichlorosilane. The resultant super-amphiphobic coating was highly repellent to all of the ethanol–water mixtures with surface tensions ranging over 26.0–72.8 mN/m, as well as excellent chemical and mechanical durability. After it was irradiated for 8 h with ultraviolet light, it was used for oil/water and oil/oil mini-separation with the help of its Janus characteristic. This was attributed to its unidirectional penetration for liquid droplets with different surface tension values. This kind of smart super-amphiphobic mesh with photochemical activity could potentially gate and sort liquids via surface tensions.