Platinum-based heterogeneous nanomaterials via wet-chemistry approaches toward electrocatalytic applications

Facile High Throughput Wet-Chemical Synthesis Approach Using a Microfluidic-Based Composition and Temperature Controlling Platform

The wet-chemical technique has been widely applied in material synthesis. In recent years, high throughput (HT) technique has shown its potential in parallel synthesis and the investigation of synthesis parameters. However, traditional ways of HT parallel synthesis require costly equipment and complex operating procedures, restricting their further applications. In this paper, we prepared a cost-effective and timesaving microfluidic-based composition and temperature controlling platform to carry out HT wet-chemical synthesis in a facile and automated workflow. The platform uses a microfluidic chip to generate 20–level concentration gradients of the two reagents and uses 100–channel reactor arrays for wet-chemical synthesis with 5–level temperature gradients. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were applied to characterize Co–Ni bimetallic powder materials synthesized under 100 different reaction conditions. X-ray photoelectron spectroscopy (XPS) was conducted to confirm the oxidation state of the products. This platform not only enables one-step determination of the minimum reaction temperature required for a wet-chemical system but also provides a significant increase in efficiency compared with the traditional wet-chemical approach. The microfluidic-based composition and temperature controlling platform shows promise in facile, efficient, and low-cost HT wet-chemical synthesis of materials.

Facile High Throughput Wet-Chemical Synthesis Approach Using a Microfluidic-Based Composition and Temperature Controlling Platform

The wet-chemical technique has been widely applied in material synthesis. In recent years, high throughput (HT) technique has shown its potential in parallel synthesis and the investigation of synthesis parameters. However, traditional ways of HT parallel synthesis require costly equipment and complex operating procedures, restricting their further applications. In this paper, we prepared a cost-effective and timesaving microfluidic-based composition and temperature controlling platform to carry out HT wet-chemical synthesis in a facile and automated workflow. The platform uses a microfluidic chip to generate 20-level concentration gradients of the two reagents and uses 100-channel reactor arrays for wet-chemical synthesis with 5-level temperature gradients. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were applied to characterize Co-Ni bimetallic powder materials synthesized under 100 different reaction conditions. X-ray photoelectron spectroscopy (XPS) was conducted to confirm the oxidation state of the products. This platform not only enables one-step determination of the minimum reaction temperature required for a wet-chemical system but also provides a significant increase in efficiency compared with the traditional wet-chemical approach. The microfluidic-based composition and temperature controlling platform shows promise in facile, efficient, and low-cost HT wet-chemical synthesis of materials.

Parameter control and property analysis in the preparation of platinum iodide nanocolloids through the electrical spark discharge method

This study employed the electrical spark discharge method to prepare platinum iodide nanocolloids at normal temperature and pressure. Wires composed of 99.5% platinum were applied as the electrodes, and 250 ppm liquid iodine was employed as the dielectric fluid. An electric discharge machine was applied to generate cyclic direct current pulse power between the electrodes. Five sets of turn-on and turn-off time (T on-T off) parameters, namely 10-10, 30-30, 50-50, 70-70, and 90-90 μs, were implemented to identify the optimal nanocolloid preparation conditions. An ultraviolet-visible spectroscope, a Zetasizer, and a transmission electron microscope were used to examine the nanocolloids' properties. The results revealed that the T on-T off parameter set of 10-10 μs was the most ideal setting for platinum iodide nanocolloid preparation. With this parameter set, the characteristic wavelengths of the nanocolloid were 285 and 350 nm, respectively; its absorbance values were 0.481 and 0.425, respectively; and its zeta potential and particle size were -30.3 mV and 61.88 nm, respectively. This parameter set yielded maximized absorbance, satisfactory suspension stability, and minimized nanoparticle sizes for the nanocolloid.

Generation of Cost-Effective Paper-Based Tissue Models through Matrix-Assisted Sacrificial 3D Printing

Due to the combined advantages of cellulose and nanoscale (diameter 20-60 nm), bacterial cellulose possesses a series of attractive features including its natural origin, moderate biosynthesis process, good biocompatibility, and cost-effectiveness. Moreover, bacterial cellulose nanofibers can be conveniently processed into three-dimensional (3D) intertwined structures and form stable paper devices after simple drying. These advantages make it suitable as the material for construction of organ-on-a-chip devices using matrix-assisted sacrificial 3D printing. We successfully fabricated various microchannel structures embedded in the bulk bacterial cellulose hydrogels and retained their integrity after the drying process. Interestingly, these paper-based devices containing hollow microchannels could be rehydrated and populated with relevant cells to form vascularized tissue models. As a proof-of-concept demonstration, we seeded human umbilical vein endothelial cells (HUVECs) into the microchannels to obtain the vasculature and inoculated the MCF-7 cells onto the surrounding matrix of the paper device to build a 3D paper-based vascularized breast tumor model. The results showed that the microchannels were perfusable, and both HUVECs and MCF-7 cells exhibited favorable proliferation behaviors. This study may provide a new strategy for constructing simple and low-cost in vitro tissue models, which may find potential applications in drug screening and personalized medicine.

Nanocatalysts for Electrocatalytic Oxidation of Ethanol

The use of ethanol as a fuel in direct alcohol fuel cells depends not only on its ease of production from renewable sources, but also on overcoming the challenges of storage and transportation. In an ethanol-based fuel cell, highly active electrocatalysts are required to break the C-C bond in ethanol for its complete oxidation at lower overpotentials, with the aim of increasing the cell performance, ethanol conversion rates, and fuel efficiency. In recent decades, the development of wet-chemistry methods has stimulated research into catalyst design, reactivity tailoring, and mechanistic investigations, and thus, created great opportunities to achieve efficient oxidation of ethanol. In this Minireview, the nanomaterials tested as electrocatalysts for the ethanol oxidation reaction in acid or alkaline environments are summarized. The focus is mainly on nanomaterials synthesized by using wet-chemistry methods, with particular attention on the relationship between the chemical and physical characteristics of the catalysts, for example, catalyst composition, morphology, structure, degree of alloying, presence of oxides or supports, and their activity for ethanol electro-oxidation. As potential alternatives to noble metals, non-noble-metal catalysts for ethanol oxidation are also briefly reviewed. Insights into further enhancing the catalytic performance through the design of efficient electrocatalysts are also provided.

Size and shape-controlled synthesis of Ru nanocrystals

Mastery over the size/shape of nanocrystals (NCs) enables control of their properties and enhancement of their usefulness for a given application. Within the past decades, the development of wet-chemistry methods leads to the blossom of research in noble metal nanomaterials with tunable sizes and shapes. We herein would prefer to devote this chapter to introduce the solution-based methods for size and shape-controlled synthesis of ruthenium (Ru) NCs, which can be summarized into five categories: (i) Synthesis of spherical Ru NCs; (ii) synthesis of one-dimensional (1D) Ru NCs, e.g. wires and rods; (iii) synthesis of two-dimensional (2D) Ru NCs, e.g. nanoplates; (iv) synthesis of Ru NCs with hollow interiors and (v) synthesis of Ru NCs with other morphologies, e.g. chains, dendrites and branches. We aim at highlighting the synthetic approaches and growth mechanisms of these types of Ru NCs. We also introduce the detailed characterization tools for analysis of Ru NCs with different sizes/shapes. With respect to the creation of great opportunities and tremendous challenges due to the accumulation in noble metal nanomaterials, we briefly make some perspectives for the future development of Ru NCs so as to provide the readers a systematic and coherent picture of this promising field. We hope this reviewing effort can provide for technical bases for effectively designing and producing Ru NCs with enhanced physical/chemical properties.

Graphical Abstract:

Novel Au Catalysis Strategy for the Synthesis of Au@Pt Core-Shell Nanoelectrocatalyst with Self-Controlled Quasi-Monolayer Pt Skin

Design of catalytically active Pt-based catalysts with minimizing the usage of Pt is a major issue in fuel cells. Herein, for the first time, we have developed a Au catalytic reduction strategy to synthesize a Au@Pt core-shell electrocatalyst with a quasi-monolayer Pt skin spontaneously formed from the gold surface catalysis. In the presence of presynthesized gold nanocrystals (used as the catalyst and Au seeds) and 4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid buffer (used as reductant), under the Au surface catalysis, platinum ions can be reduced and deposited on the gold nanocrystals to form a Pt skin surface with a quasi-monatomic thickness. In the present strategy, Pt ions can be reduced only under the catalysis of gold surface and thus when the surface of Au NPs is covered by a monatomic Pt layer, the reduction reaction of Pt ions will be spontaneously turned off. Therefore, the significant advantage of this synthesis strategy is that the formation of quasi-monolayer Pt skin surface can be self-controlled and is completely free of controlling the dosage of platinum ions and the size distribution of Au cores. The synthesized Au@Pt core@shell structure exhibited enhanced electrocatalytic activities for oxygen reduction reaction and methanol oxidation reaction, which are 6.87 and 10.17 times greater than those of Pt/C catalyst, respectively. The present study provides a new strategy for obtaining high-performance bimetallic/multimetallic electrocatalysts with high utilization of precious metals.

Uniformly dispersed platinum-cobalt alloy nanoparticles with stable compositions on carbon substrates for methanol oxidation reaction

Alloying platinum (Pt) with suitable transition metals is effective way to enhance their catalytic performance for methanol oxidation reaction, and reduce their cost at mean time. Herein, we report our investigation on the synthesis of bimetallic platinum-cobalt (PtCo) alloy nanoparticles, their activation, as well as the catalytic evaluation for methanol oxidation reaction. The strategy starts with the synthesis of PtCo alloy nanoparticles in an organic medium, followed by loading on carbon substrates. We then remove the capping agent by refluxing the carbon-supported PtCo particles in acetic acid before electrochemical measurements. We emphasize the change in composition of the alloys during refluxing process, and the initial PtCo alloys with Pt/Co ratio of 1/2 turns into stable alloys with Pt/Co ratio of 3/1. The final Pt₃Co particles have uniform distribution on carbon substrates, and exhibit activity with 2.4 and 1.5 times of that for commercial Pt/C and PtRu/C for methanol oxidation reaction.

A selective electrocatalyst-based direct methanol fuel cell operated at high concentrations of methanol

Owing to the serious crossover of methanol from the anode to the cathode through the polymer electrolyte membrane, direct methanol fuel cells (DMFCs) usually use dilute methanol solutions as fuel. However, the use of high-concentration methanol is highly demanded to improve the energy density of a DMFC system. Instead of the conventional strategies (for example, improving the fuel-feed system, membrane development, modification of electrode, and water management), we demonstrate the use of selective electrocatalysts to run a DMFC at high concentrations of methanol. In particular, at an operating temperature of 80°C, the as-fabricated DMFC with core-shell-shell Au@Ag₂S@Pt nanocomposites at the anode and core-shell Au@Pd nanoparticles at the cathode produces a maximum power density of 89.7 mW cm^-2 at a methanol feed concentration of 10 M and maintains good performance at a methanol concentration of up to 15 M. The high selectivity of the electrocatalysts achieved through structural construction accounts for the successful operation of the DMFC at high concentrations of methanol.

Facile synthesis of Pt nanoparticles supported on anatase TiO2 nanotubes with good photo-electrocatalysis performance for methanol

A Pt/TNTs/C catalyst showed enhanced MOR performance under the light illumination.

Fine silver sulfide–platinum nanocomposites supported on carbon substrates for the methanol oxidation reaction

Carbon-supported Ag₂S–Pt nanocomposites with fine sizes and uniform dispersions were synthesized for catalyzing methanol oxidation reaction.

Effect of electronic coupling on the electrocatalytic performance of platinum metal

The relationship between the electronic coupling effect and electrocatalytic property of platinum metal was investigated through a core–shell construction.

Tailoring ruthenium exposure to enhance the performance of fcc platinum@ruthenium core–shell electrocatalysts in the oxygen evolution reaction

Stable and active core–shell bimetallic nanoparticles for the oxygen evolution reaction are rapidly tailored in a scalable continuous-flow reactor.

Facile in situ synthesis and characterization of a novel PANI/Fe3O4/Ag nanocomposite and investigation of catalytic applications

A novel magnetic hybrid nanocomposite was successfully synthesized via in situ polymerization, well characterized by FT-IR, XRD, EDX and FE-SEM analysis, and its catalytic activity shown in the synthesis of pharmaceutically important pyrans.

Sheet-on-sphere structured Ag/AgBr@InVO4 heterojunctions and enhanced visible-light photocatalytic activity

Sheet-on-sphere Ag/AgBr@InVO₄ displayed excellent photocatalytic degradation of RhB, which was attributed to enhanced visible-light absorption and anti-combination of electrons/holes through it's heterostructure.

Ultra-fast microwave-assisted reverse microemulsion synthesis of Fe3O4@SiO2 core–shell nanoparticles as a highly recyclable silver nanoparticle catalytic platform in the reduction of 4-nitroaniline

Highly efficient silver catalytic platform Fe₃O₄@SiO₂ core–shell nanoparticles is synthesized via novel microwave-assisted reverse microemulsion fast methodology.

Two-dimensional iron–tetracyanoquinodimethane (Fe–TCNQ) monolayer: an efficient electrocatalyst for the oxygen reduction reaction

The Fe–TCNQ monolayer exhibit superior catalytic performance for oxygen reduction and can serve as a promising alternative to Pt-based catalysts.