The pH dependent surface charging and points of zero charge. IX. Update

Interaction of zinc oxide nanoparticles with soil colloidal suspensions

The properties of soil colloids determine the interaction with nanoparticles, their behavior, and destiny in the soil environment including soil solutions. This study examines how several properties of soil colloids, including pH, phosphorus content, clay minerals, and iron oxyhydroxides, influence the interaction with zinc oxide nanoparticles (ZnO-nps). For the experimental setup, four different soils were selected from the temperate climate of central Europe, in Slovakia, exhibiting pH values ranging from 4.6 to 8.0. Two concentrations of ZnO-nps suspended in water, 20 and 200 mg Zn∙L-1 were applied to the colloidal suspensions extracted from the soils and shaken for 24 h. Then the soil colloids were separated into three fractions, 100-1000 nm in size, 1-100 nm in size, and dissolved. Concentrations of Al, Si, Fe, Mn, P, and Zn were measured in these fractions, providing a comprehensive understanding of ZnO-NP distribution and interaction with soil colloids. The study reveals that soil pH significantly affects the distribution of Zn from ZnO-nps across different size fractions. However, the concentration of Fe, Al, and Si had an even greater impact on the concentration of dissolved Zn. Additionally, behavior of Zn following ZnO-NP application is associated with soil P content, where P may stabilize the ZnO-nps. These findings enhance the knowledge of nanoparticle behavior in various soil matrices and contribute to developing more stable, efficient, and easily useable nanoparticle-based applications in environmental science and agriculture.

Competitive adsorption of arsenate and phosphate on hematite facets: Molecular insights for enhanced arsenic retention

Understanding the competition for adsorption between arsenate and other common oxyanions at mineral-water interfaces is critical for enhancing arsenate retention in the subsurface environment and mitigating exposure risks. This study investigated the competitive adsorption between arsenate and phosphate on hematite facets using batch experiments, together with in-situ infrared spectroscopy, two-dimensional correlation spectroscopy (2D-COS), and ab initio molecular dynamic (AIMD) simulations. This study's findings revealed that hematite exhibited notable selectivity for arsenate over phosphate in both adsorption capacity and rate, with selectivity significantly influenced by the exposed facets of the hematite and reaction concentrations. To wit, the (001) facet exhibited stronger selectivity for arsenate than the (110) facet, and increasing reaction concentration further enhances this selectivity. This selectivity was driven by surface hydroxy structure-mediated complexation, where both surfaces primarily formed stable inner-sphere monodentate complexes with an affinity for arsenate. On the (001) surface, the available Fe2OH featured two close-spaced iron sites (Fe - Fe ≈ 2.86 Å), enabling arsenate to interact with both sites simultaneously, significantly boosting arsenate selectivity. At higher surface loadings, the (110) surface formed partially more selective bidentate binuclear complexes, further enhancing arsenate retention. These findings emphasize the critical role of interfacial complexation, particularly the formation of inner-sphere bidentate complexes and the availability of iron sites, in controlling arsenate retention. By tailoring mineral facets and optimizing reaction conditions to improve iron site availability and promote bidentate complexation, arsenate retention can be significantly enhanced in phosphate-rich aquatic environments, such as rivers and groundwater in agricultural areas.

Photocatalysis of Adsorbed Catechol on Degussa P25 TiO2 at the Air-Solid Interface

Semiconductor photocatalysis with commercial TiO2 (Degussa P25) has shown significant potential in water treatment of organic pollutants. However, the photoinduced reactions of adsorbed catechol, a phenolic air pollutant from biomass burning and combustion emissions, at the air-solid interface of TiO2 remain unexplored. Herein we examine the photocatalytic decay of catechol in the presence of water vapor, which acts as an electron acceptor. Experiments under variable cut-off wavelengths of irradiation (λcut-off ≥ 320, 400, and 515 nm) distinguish the mechanistic contribution of a ligand-to-metal charge-transfer (LMCT) complex of surface chemisorbed catechol on TiO2. The LMCT complex injects electrons into the conduction band of TiO2 from the highest occupied molecular orbital of catechol by visible light (≥2.11 eV) excitation. The deconvolution of diffuse reflectance UV-visible spectral bands from LMCT complexes of TiO2 with catechol, o-semiquinone radical, and quinone and the quantification of the evolving gaseous products follow a consecutive kinetic model. CO2(g) and CO(g) final oxidation products are monitored by gas chromatography and Fourier-transform infrared spectroscopy. The apparent quantum efficiency at variable λcut-off are determined for reactant loss (Φ- TiO2/catechol = 0.79 ± 0.19) and product growth ΦCO2 = 0.76 ± 0.08). Spectroscopic and electrochemical measurements reveal the energy band diagram for the LMCT of TiO2/catechol. Two photocatalytic mechanisms are analyzed based on chemical transformations and environmental relevance.

Understanding the relationship between pore size, surface charge density, and Cu2+ adsorption in mesoporous silica

This research delved into the influence of mesoporous silica's surface charge density on the adsorption of Cu2+. The synthesis of mesoporous silica employed the hydrothermal method, with pore size controlled by varying the length of trimethylammonium bromide (CnTAB, n = 12, 14, 16) chains. Gas adsorption techniques and transmission electron microscopy characterized the mesoporous silica structure. Surface charge densities of the mesoporous silica were determined through potentiometric titration, while surface hydroxyl densities were assessed using the thermogravimetric method. Subsequently, batch adsorption experiments were conducted to study the adsorption of Cu2+ in mesoporous silica, and the process was comprehensively analyzed using Atomic absorption spectrometry (AAS), Fourier transform infrared (FTIR), and L3 edge X-ray absorption near edge structure (XANES). The research findings suggest a positive correlation between the pore size of mesoporous silica, its surface charge density, and the adsorption capacity for Cu2+. More specifically, as the pore size increases within the 3-4.1 nm range, the surface charge density and the adsorption capacity for Cu2+ also increase. Our findings provide valuable insights into the relationship between the physicochemical properties of mesoporous silica and the adsorption behavior of Cu2+, offering potential applications in areas such as environmental remediation and catalysis.

Removal of malachite green from water: Comparison of adsorption in a residue-derived AC versus photocatalytic oxidation with TiO2 and study of the adsorption-photocatalysis synergy

The literature rarely compiles studies devoted to the removal of pollutants in aqueous media comparing adsorption and photocatalytic degradation, and does not pay enough attention to the analysis of combined adsorption-photocatalytic oxidation processes. In the present manuscript, the removal of malachite green (MG) from aqueous solutions has been investigated in three different sustainable scenarios: i) adsorption on activated carbon (AC) derived from a residue, luffa cylindrica, ii) photocatalytic oxidation under simulated solar light using titanium dioxide (TP) and iii) combined adsorption-photocatalytic oxidation using TP-AC (70/30 wt./wt.) under simulated solar light. The study has revealed that in the three scenarios and studied conditions, the total removal of this endocrine-disrupting dye from the solution takes place in the assayed time, 2 h, in some cases just in a few minutes. MG adsorption in the AC is a very fast and efficient removal method. MG photocatalytic oxidation with TP also occurs efficiently, although the oxidized MG is not totally mineralized. MG removal using the TP-AC composite under simulated solar light occurs only slightly faster to the MG adsorption in the AC, being adsorption the dominating MG removal mechanism for TP-AC. Thus, more than 90% of the removed MG with TP-AC under simulated solar light is adsorbed in this carbon-containing composite. The obtained results highlight the interest in adsorption, being the selection of the most suitable removal method dependent on several factors (i.e., the cost of the AC regeneration, for adsorption, or the toxicity of the intermediate oxidation species, for photooxidation). Paying attention to MG photooxidation with TiO2, comparison of two working photodegradation schemes shows that the direct photodegradation of MG from solution, avoiding any initial dark equilibrium period, is more efficient from a time perspective. The use of scavengers has proved that MG photodegradation occurs via an oxidation mechanism dominated by superoxide anion radicals.

A review of flotation reagents for bastnäsite-(Ce) rare earth ore

Given the indispensability and immense value of rare earth elements for scientific and technological advancements in the 21st century, extracting high-quality rare earth resources from nature has become a global priority. Bastnäsite-(Ce) is one of the known rare earth minerals with high rare earth content and wide distribution, which occupies a pivotal position in human life and high-end production activities, making its efficient development and utilization crucial. In recent years, research on separating bastnäsite-(Ce) from gangue minerals has focused on the flotation process, with flotation reagents playing a critical role in achieving effective separation. This paper provides a detailed summary of current research on the behavior of bastnäsite-(Ce) flotation agents on minerals, their interaction with mineral surfaces during flotation separation, and outlines future prospects for further research.

The pH dependent surface charging and points of zero charge. X. Update

Surfaces are often characterized by their points of zero charge (PZC) and isoelectric points (IEP). Different authors use these terms for different quantities, which may be equal to the actual PZC under certain conditions. Several popular methods lead to results which are inappropriately termed PZC. This present review is limited to zero-points obtained in the presence of inert electrolytes (halides, nitrates, and perchlorates of the 1st group metals). IEP are reported for all kinds of materials. PZC of metal oxides obtained as common intersection points of potentiometric curves for 3 or more ionic strengths (or by means of equivalent methods) are also reported, while the apparent PZC obtained by mass titration, pH-drift method, etc. are deliberately neglected. The results published in the recent publications and older results overlooked in the previous compilations by the same author are reported. The PZC/IEP are accompanied by information on the temperature and on the nature and concentration of supporting electrolyte (if available). The references to previous reviews by the same author allow to compare the newest results with the PZC/IEP of similar materials from the older literature.

Exploring Alternatives to Polyacrylamide: A Comparative Study of Novel Polymers in the Flocculation and Dewatering of Iron Ore Tailings

Despite being widely used in tailings treatment, polyacrylamide continues to face performance challenges. In this study, two commercial polyacrylamides with different molecular weights were used to flocculate iron ore tailings and their performance was compared with two polymers designed to treat oil sand tailings: poly(vinylbenzyl)trimethylammonium chloride and partially hydrolyzed poly(methyl acrylate) grafted onto ethylene-propylene-diene copolymer backbones. The polyacrylamide with the highest molecular weight performed better than the one with the lowest molecular weight, but its efficiency was still considerably lower than what would be desired for good solid-liquid separation. The new polymer flocculants performed better than the commercially available polyacrylamides but retained high amounts of water in the sediments. This comparison shows that polymers other than polyacrylamide may be used to treat iron ore tailings.

Preparation and Adsorption Behavior of Ce(III)-MOF for Phosphate and Fluoride Ion Removal from Aqueous Solutions

The discharge of inorganic pollutants like phosphate and fluoride is a cause of mounting concern to the world due to the substantial environmental and human health risk. Adsorption is one of the most common and affordable technologies widely utilized for removing inorganic pollutants such as phosphate and fluoride anions. Investigating efficient sorbents for the adsorption of these pollutants is extremely important and challenging. This work aimed at studying the adsorption efficiency of the Ce(III)-BDC metal-organic framework (MOF) for the removal of these anions from an aqueous solution using a batch mode. Powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET), and scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) techniques evidenced the successful synthesis of Ce(III)-BDC MOF in water as a solvent without any energy input within a short reaction time. The outstanding removal efficiency of phosphate and fluoride was exhibited at an optimized pH (3, 4), adsorbent dose (0.20, 0.35 g), contact time (3, 6 h), agitation speed (120, 100 rpm), and concentration (10, 15 ppm) for each ion, respectively. The experiment on the effect of coexisting ions demonstrated that SO₄^2- and PO₄^3- ions are the primary interfering ions in phosphate and fluoride adsorption, respectively, while the HCO₃^- and Cl^- ions were found to have interfered less. Furthermore, the isotherm experiment showed that the equilibrium data fitted well with the Langmuir isotherm model and the kinetic data correlated well with the pseudo-second-order model for both ions. The results of thermodynamic parameters such as ΔH°, ΔG°, and ΔS° evidenced an endothermic and spontaneous process. The regeneration of the adsorbent made using water and NaOH solution showed the easy regeneration of the sorbent Ce(III)-BDC MOF, which can be reused four times, revealing its potential application for the removal of these anions from aqueous environment.

Equilibrium isotope fractionation factors of H exchange between steam and soil clay fractions

RATIONALE

Steam equilibration overcomes the problem of the traditional measurements of H isotope compositions, which leave an arbitrary amount of adsorbed water in the sample, by controlling for the entire exchangeable H pool, including adsorbed water and hydroxyl-H. However, the use of steam equilibration to determine nonexchangeable stable H isotope compositions in environmental media (expressed as δ² H_n values) by mathematically eliminating the influence of exchangeable H after sample equilibration with waters of known H-isotopic composition requires the knowledge of the equilibrium isotope fractionation factor between steam-H and exchangeable H of the sample (α_ex-w ), which is frequently unknown.

METHODS

We developed a new method to determine the α_ex-w values for clay minerals, topsoil clay fractions, and mica by manipulating the contributions of exchangeable H to the total H pool via different degrees of post-equilibration sample drying. We measured the δ² H values of steam-equilibrated mineral and soil samples using elemental analyzer-pyrolysis-isotope ratio mass spectrometry.

RESULTS

The α_ex-w values of seven clay minerals ranged from 1.071 to 1.140, and those of 19 topsoil clay fractions ranged from 0.885 to 1.216. The α_ex-w value of USGS57 biotite, USGS58 muscovite, and of cellulose was 0.965, 0.871, and 1.175, respectively. The method did not work for kaolinite, because its small exchangeable H pool did not respond to the selected drying conditions. Structurally different mineral groups such as two- and three-layer clay minerals or mica showed systematically different α_ex-w values. The α_ex-w value of the topsoil clay fractions correlated with the soil clay content (r = 0.63, P = 0.004), the local mean annual temperature (r = 0.68, P = 0.001), and the δ² H values of local precipitation (r = 0.72, P < 0.001), likely to reflect the different clay mineralogy under different weathering regimes.

CONCLUSIONS

Our new α_ex-w determination method yielded realistic results in line with the few previously published values for cellulose. The determined α_ex-w values were similar to the widely assumed values of 1.00-1.08 in the literature, suggesting that the adoption of one of these values in steam equilibration approaches is appropriate.

SiO2 nanospheres as surfactant and template in aqueous dispersion polymerizations yielding highly nanoporous resin particles

HYPOTHESIS

High nitrogen containing resins such as poly(melamine-co-formaldehyde) (PMF) are known for their very good adsorption properties. Until now, using an ecofriendly hard-templating approach with SiO₂ nanospheres in water for synthesis, only yielded either highly porous particles with diameters up to 1 µm or non-porous particles with diameters above 1 µm. Small particles cannot be used as fixed bed adsorbents in columns because of the very high pressure occurring.

EXPERIMENTS

To yield particles with high porosity and larger diameters for the use as fixed bed adsorbent, we investigated the influence of several synthesis parameters on porosity and particle morphology.

FINDINGS

From all variations, we proposed a mechanism for the complex interplay between the PMF prepolymer and resin species with SiO₂ nanoparticles acting both as Pickering-like surfactant and template particle. With this knowledge we were able to produce a suitable column material with high specific surface area up to 260 m²/g. We then proved the application of this material for aqueous dichromate adsorption in batch, yielding a maximum capacity of 138 mg/g with recyclability. In column experiments, the contamination of 5 mg/L dichromate in water was reduced to drinking water safe levels for an influent volume equal to over 160 bed volumes.

5-Fluorouracil-Loaded PLGA Nanoparticles: Formulation, Physicochemical Characterisation, and In VitroAnti-Cancer Activity

The major goal of this investigation was to prepare a drug delivery of polymeric nanoparticles (NPs) from 5-fluorouracil (FU) that could be delivered intravenously and improve the therapeutic index of the FU. In order to achieve this, interfacial deposition method was used to prepare FU entrapped poly-(lactic-co-glycolic acid) nanoparticles (FU-PLGA-NPs). The influence of various experimental settings on the effectiveness of FU integration into the NPs was assessed. Our findings show that the technique used to prepare the organic phase and the ratio of the organic phase to the aqueous phase had the greatest impact on the effectiveness of FU integration into NPs. The results show that the preparation process produced spherical, homogenous, negatively charged particles with a nanometric size of 200 nm that are acceptable for intravenous delivery. A quick initial release over 24 h and then slow and steady release of FU from the formed NPs, exhibiting a biphasic pattern. Through the human small cell lung cancer cell line (NCI-H69), the in vitro anti-cancer potential of the FU-PLGA-NPs was evaluated. It was then associated to the in vitro anti-cancer potential of the marketed formulation Fluracil®. Investigations were also conducted into Cremophor-EL (Cre-EL) potential activity on live cells. The viability of NCI-H69 cells was drastically reduced when they were exposed to 50 µg·mL-1 Fluracil®. Our findings show that the integration of FU in NPs significantly increases the drug cytotoxic effect in comparison to Fluracil®, with this potential effect being particularly important for extended incubation durations.

Water Structure in the Electrical Double Layer and the Contributions to the Total Interfacial Potential at Different Surface Charge Densities

The electric double layer governs the processes of all charged surfaces in aqueous solutions; however, elucidating the structure of the water molecules is challenging for even the most advanced spectroscopic techniques. Here, we present the individual Stern layer and diffuse layer OH stretching spectra at the silica/water interface in the presence of NaCl over a wide pH range using a combination of vibrational sum frequency generation spectroscopy, heterodyned second harmonic generation, and streaming potential measurements. We find that the Stern layer water molecules and diffuse layer water molecules respond differently to pH changes: unlike the diffuse layer, whose water molecules remain net-oriented in one direction, water molecules in the Stern layer flip their net orientation as the solution pH is reduced from basic to acidic. We obtain an experimental estimate of the non-Gouy-Chapman (Stern) potential contribution to the total potential drop across the insulator/electrolyte interface and discuss it in the context of dipolar, quadrupolar, and higher order potential contributions that vary with the observed changes in the net orientation of water in the Stern layer. Our findings show that a purely Gouy-Chapman (Stern) view is insufficient to accurately describe the electrical double layer of aqueous interfaces.

Molybdate Recovery by Adsorption onto Silica Matrix and Iron Oxide Based Composites

Aggressive industrial development over the last century involved different heavy metals being used, including high quantities of molybdenum, which need to be treated before discharge in industrial waters. Molybdenum’s market price and industrial applicability make its recovery a big challenge. In the present study the possibility to recover molybdenum ions from aqueous solutions by adsorption on a composite material based on silica matrix and iron oxides—SiO₂FexOy—was evaluated. Tests were performed in order to determine the influence of adsorbent material dose, initial solution pH, contact time and temperature over adsorption capacity of synthesized adsorbent material. For better understanding of the adsorption process, the obtained experimental data were modelled using Langmuir, Freundlich and Sips adsorption isotherms. Based on the obtained data, it can proved that the Sips isotherm was describing with better orderliness the studied process, obtaining a maximum adsorption capacity of 10.95 mg MoO42− for each gram of material. By modelling the studied adsorption process, it was proven that the pseudo-second order model is accurately describing the adsorption process. By fitting experimental data with Weber-Morris model, it was proven that MoO42− adsorption is a complex process, occurring in two different steps, one controlled by diffusion and the second one controlled by mass transfer. Further, studies were performed in order to determine the optimum pH value needed to obtain maximum adsorption capacity, but also to determine which are the adsorbed species. From pH and desorption studies, it was proven that molybdate adsorption is a physical process. In order to establish the adsorption mechanism, the thermodynamic parameters (ΔG0, ΔH0 and ΔS0) were determined.