Natural and engineered clays and clay minerals for the removal of poly- and perfluoroalkyl substances from water: State-of-the-art and future perspectives

Aminated clay-polymer composite as soil amendment for stabilizing the short- and long-chain per- and poly-fluoroalkyl substances in contaminated soil

Soils contaminated with per- and poly- fluoroalkyl substances (PFAS) require immediate remediation to protect the surrounding environment and human health. A novel animated clay-polymer composite was developed by applying polyethyleneimine (PEI) solution onto a montmorillonite clay-chitosan polymer composite. The resulting product, PEI-modified montmorillonite chitosan beads (MMTCBs) were characterized as an adsorptive soil amendment for immobilizing PFAS contaminants. The MMTCBs exhibited good efficiency to adsorb the PFAS, showing adsorption capacities of 12.2, 16.7, 18.5, and 20.8 mg g-1 for PFBA, PFBS, PFOA, and PFOS, respectively, which were higher than those obtained by granular activated carbon (GAC) (i.e., an adsorbent used as a reference). Column leaching tests demonstrated that amending soil with 10% MMTCBs resulted in a substantial decrease in the leaching of PFOA, PFOS, PFBA, and PFBS by 90%, 100%, 64%, and 68%, respectively. These reductions were comparable to the values obtained for GAC-modified soil, particularly for long-chain PFAS. Incorporating MMTCBs into the soil not only preserved the structural integrity of the soil matrix but also enhanced its shear strength (kPa). Conversely, adding GAC to the soil resulted in a reduction of the soil's mechanical properties.

Natural mineral and industrial solid waste-based adsorbent for perfluorooctanoic acid and perfluorooctane sulfonate removal from surface water: Advances and prospects

PER: and polyfluorinated alkyl substances, especially perfluorooctanoic acid and perfluorooctane sulfonic acid (PFOX), have attracted considerable attention lately because of their widespread occurrence in aquatic environment and potential biological toxicity to animals and human beings. The development of economical, efficient, and engineerable adsorbents for removing PFOX in water has become one of the research focuses. This review summarized the recent progress on natural mineral and industrial solid based adsorbent (NM&ISW-A) and removal mechanisms concerning PFOX onto NM&ISW-A, as well as proposed the current challenges and future perspectives of using NM&ISW-A for PFOX removal in water. Kaolinite and montmorillonite are usually used as model clay minerals for PFOX removal, and have been proved to adsorb PFOX by ligand exchange and electrostatic attraction. Fe-based minerals, such as goethite, magnetite, and hematite, have better PFOX adsorption capacity than clay minerals. The adsorbent prepared from industrial solid waste by high temperature roasting has great potential application prospects. Fabricating nanomaterials, amination modification, surfactant modification, fluorination modification, developing versatile composites, and designing special porous structure are beneficial to improve the adsorption performance of PFOX onto NM&ISW-A by enhancing the specific surface area, positive charge, and hydrophobicity. Electrostatic interaction, hydrophobic interaction, hydrogen bond, ligand and ion exchange, and self-aggregation (formation of micelle or hemimicelle) are the main adsorption mechanisms of PFOX by NM&ISW-A. Among them, electrostatic and hydrophobic interactions play a considerable role in the removal of PFOX by NM&ISW-A. Therefore, NM&ISW-A with electrostatic functionalities and considerable hydrophobic segments enables rapid, efficient, and high-capacity removal of PFOX. The future directions of NM&ISW-A for PFOX removal include the preparation and regeneration of engineerable NM&ISW-A, the development of coupling technology for PFOX removal based on NM&ISW-A, the in-depth research on adsorption mechanism of PFOX by NM&ISW-A, as well as the development of NM&ISW-A for PFOX alternatives removal. This review paper would be helpful the comprehensive understanding of NM&ISW-A potential for PFOX removal and the PFOX removal mechanisms, and identifies the gaps for future research and development.

Highly efficient mica-incorporated graphene oxide-based membranes for water purification and desalination

Graphene oxide (GO) has become the most attractive material for membrane technology owing to its potential application as a nanofiller in water treatment, purification, and desalination. In this study, we incorporated mica as a cross-linking reagent to increase the interlayer spacing and stability of GO sheets and fabricated a mica/GO (MGO) membrane for the first time. The MGO membrane (260 ± 10 nm) exhibits 100% rejection for biomolecules such as tannic acid (TA) and bovine serum albumin (BSA) and >99% rejection for multiple probe molecules, such as methylene blue, methyl orange, congo red, and rhodamine B. The high rejection of membranes can be attributed to the surface interaction of mica with GO nanosheets through covalent interaction, which enhances the stability and separation efficiency of the membranes for probe ions and molecules. This ultrathin MGO membrane also exhibits much better water permeability at 870 ± 5 L m-2 h-1 bar-1, which is 10-100 times greater than that reported for pure GO and GO-based composite membranes. Additionally, the membrane shows high rejection for salt ions (70%). Furthermore, the stability of the MGO membranes was evaluated under various conditions, and the membranes demonstrated remarkable stability for up to 60 days in a neutral environment.

Adsorption of per- and poly-fluoroalkyl substances (PFAS) on Ni: A DFT investigation

Electrocatalytic destruction of per- and polyfluoroalkyl substances (PFAS) is an emerging approach for treatment of PFAS-contaminated water. In this study, a systematic ab initio investigation of PFAS adsorption on Ni, a widely used electrocatalyst, was conducted by means of dispersion-corrected Density Functional Theory (DFT) calculations. The objective of this investigation was to elucidate the adsorption characteristics and charge transfer mechanisms of different PFAS molecules on Ni surfaces. PFAS adsorption on three of the most thermodynamically favorable Ni surface facets, namely (001), (110), and (111), was investigated. Additionally, the role of PFAS chain length and functional group was studied by comparing the adsorption characteristics of different PFAS compounds, namely perfluorooctanesulfonic acid (PFOS), perfluorooctanoic acid (PFOA), perfluorobutanesulfonic acid (PFBS), and perfluorobutanoic acid (PFBA). For each PFAS molecule-Ni surface facet pair, different adsorption configurations were considered. Further calculations were carried out to reveal the effect of solvation, pre-adsorbed atomic hydrogen (H), and surface defects on the adsorption energy. Overall, the results revealed that the adsorption of PFAS on Ni surfaces is energetically favorable, and that the adsorption is primarily driven by the functional groups. The presence of preadsorbed H and the inclusion of solvation produced less exothermic adsorption energies, while surface vacancy defects showed mixed effects on PFAS adsorption. Taken together, the results of this study suggest that Ni is a promising electrocatalyst for PFAS adsorption and destruction, and that proper control for the exposed facets and surface defects could enhance the adsorption stability.

Innovative soil fluoride estimation method: dual polarimetric saline-associated fluoride for agricultural patches

Fluoride and its constituents in soil affect plant growth and public health. In this study, soil fluoride was measured for the semi-arid regions in southern India, using Sentinel-1 data in conjunction with the dual polarimetric saline-associated fluoride model (also known as fluoride model). A loss angle was estimated from laboratory-based dielectric components of soil samples with strong electrical conductivity under high and low fluoride conditions. The conductivity loss angle and real and imaginary dielectric constants were used to study fluoride salt's dielectric behavior. The imaginary dielectric component sensitive to dielectric loss could predict fluoride across large areas over time. This was statistically analyzed with R2 = 0.86, RMSE = 1.90, and bias = 0.35 showing a promising depiction that C-band SAR data can distinguish fluoride levels over varied clay soil and soil with varying vegetation development. Moreover, the association between biomass and simulated fluoride helped to identify fluoride-tolerant and non-tolerant crops. The study found that Sorghum and Oryza sativa tolerate saline-associated fluoride, whereas Peanut and Allium do not. Furthermore, the model successfully retrieves fluoride from saline salts based on tangent loss.

Progress in the application of ionic liquids and deep eutectic solvents for the separation and quantification of per- and polyfluoroalkyl substances

Per- and polyfluoroalkyl substances (PFASs), often labeled as "forever chemicals," earned this moniker due to their widespread presence in the environment, bioaccumulative tendencies, and resistance to remediation efforts. Employed for decades in various applications, spanning from stain-resistant fabrics to grease-proof food containers and fire-fighting foams, PFASs have evolved into an anthropogenic nightmare. Their adverse impact on human health, including immune dysfunction, infertility, and a spectrum of cancers, is alarming. Conventional water treatment methods, notably in the case of short-chain congeners, struggle to effectively eliminate PFASs, underscoring the pressing need for enhanced adsorbents. In recent years, there has been a prominent surge in the exploration of innovative techniques centered around ionic liquids (ILs) and deep eutectic solvents (DESs) for the removal of PFASs from various sources, including food samples like cooking oil, as well as environmental waters. In this Review, we delve into key advancements and discoveries related to the utilization of ILs and DESs as media for the liquid-liquid extraction of PFASs, as well as their applications as sorbents on solid-state or nanoscale supports. Our exploration encompasses groundbreaking approaches, including the utilization of dicationic ILs for ultra-sensitive mass spectrometric PFAS detection, alongside the innovative application of fluorinated ILs and hydrophobic DESs, enabling highly efficient PFAS sequestration. The landscape of existing PFAS extraction methods is riddled with formidable challenges, including limited selectivity, matrix interferences, subpar extraction efficiency, exorbitant costs, laborious procedures, ecological consequences, and a lack of standardization. Given these challenges, our review unequivocally asserts the pivotal role ILs and DESs will play in shaping the next generation of PFAS remediation strategies. Rigorous characterization of water solubility, toxicity, and biodegradation, along with improved recyclability and thorough techno-economic analyses, are essential for further progress. Future focus must also extend to addressing short-chain PFASs (such as PFBS) and PFAS alternatives (including ADONA, GenX, F-53B), which often pose higher toxicity risks than the compounds they aim to replace. A forward-thinking approach will integrate cutting-edge data-driven techniques, such as machine learning, to enhance our understanding and response to PFAS-related issues. Finally, we advocate seamless integration of PFAS separation with advanced treatment, efficiently isolating and destroying these compounds for a lasting solution to contamination challenges.

A novel montmorillonite clay-cetylpyridinium chloride material for reducing PFAS leachability and bioavailability from soils

Soils contaminated by per- and polyfluoroalkyl substances (PFAS) present a significant threat to both ecological and human health. Extensive research efforts are currently underway to develop effective strategies for immobilizing these chemicals in soils. In this study, calcium montmorillonite was modified with cetylpyridinium chloride (CPC-CM) to enhance its electrostatic and hydrophobic interactions with PFAS. CPC-CM exhibited high adsorption for perfluorooctanoate acid (PFOA), perfluorooctane sulfonate (PFOS) and 8:2 fluorotelomer sulfonic acids (8:2 FTSA) across initial concentrations of 50-1000 μg/L, outperforming both the parent CM and L-carnitine modified CM. Soil leaching tests demonstrated the superior immobilization capabilities of the CPC-CM, maintaining an average PFAS leaching rate below 7% after 120-day incubation. In the context of human exposure scenarios, the in vitro bioaccessibility and in vivo bioavailability of PFAS in soils were measured by gastrointestinal extraction and mouse assay. CPC-CM treatment effectively reduced the bioaccessibility (by up to 84%) and bioavailability (by up to 76%) of PFAS in soils. Furthermore, the safety and efficacy of CPC-CM were evaluated using enteric microorganisms of mice. CPC-CM treatment mitigated PFAS-induced changes in the abundance of Bacteroidetes and Firmicutes, thereby reducing PFAS-induced health risks for humans. Overall, CPC-CM synthesized in this study demonstrated superior adsorption performance and application safety, offering a highly promising approach for remediating PFAS-contaminated soil.

PFAS remediation in soil: An evaluation of carbon-based materials for contaminant sequestration

The presence of per- and poly-fluoroalkyl substances (PFAS) in soils is a global concern as these emerging contaminants are highly resistant to degradation and cause adverse effects on human and environmental health at very low concentrations. Sequestering PFAS in soils using carbon-based materials is a low-cost and effective strategy to minimize pollutant bioavailability and exposure, and may offer potential long-term remediation of PFAS in the environment. This paper provides a comprehensive evaluation of current insights on sequestration of PFAS in soil using carbon-based sorbents. Hydrophobic effects originating from fluorinated carbon (C-F) backbone "tail" and electrostatic interactions deriving from functional groups on the molecules' "head" are the two driving forces governing PFAS sorption. Consequently, varying C-F chain lengths and polar functional groups significantly alter PFAS availability and leachability. Furthermore, matrix parameters such as soil organic matter, inorganic minerals, and pH significantly impact PFAS sequestration by sorbent amendments. Materials such as activated carbon, biochar, carbon nanotubes, and their composites are the primary C-based materials used for PFAS adsorption. Importantly, modifying the carbon structural and surface chemistry is essential for increasing the active sorption sites and for strengthening interactions with PFAS. This review evaluates current literature, identifies knowledge gaps in current remediation technologies and addresses future strategies on the sequestration of PFAS in contaminated soil using sustainable novel C-based sorbents.

Recent advances in the application of magnetic materials for the management of perfluoroalkyl substances in aqueous phases

Perfluoroalkyl substances (PFASs) are a class of artificially synthesised organic compounds extensively used in both industrial and consumer products owing to their unique characteristics. However, their persistence in the environment and potential risk to health have raised serious global concerns. Therefore, developing effective techniques to identify, eliminate, and degrade these pollutants in water are crucial. Owing to their high surface area, magnetic responsiveness, redox sensitivity, and ease of separation, magnetic materials have been considered for the treatment of PFASs from water in recent years. This review provides a comprehensive overview of the recent use of magnetic materials for the detection, removal, and degradation of PFASs in aqueous solutions. First, the use of magnetic materials for sensitive and precise detection of PFASs is addressed. Second, the adsorption of PFASs using magnetic materials is discussed. Several magnetic materials, including iron oxides, ferrites, and magnetic carbon composites, have been explored as efficient adsorbents for PFASs removal from water. Surface modification, functionalization, and composite fabrication have been employed to improve the adsorption effectiveness and selectivity of magnetic materials for PFASs. The final section of this review focuses on the advanced oxidation for PFASs using magnetic materials. This review suggests that magnetic materials have demonstrated considerable potential for use in various environmental remediation applications, as well as in the treatment of PFASs-contaminated water.

Substitution and Orientation Effects on the Crystallinity and PFAS Adsorption of Olefin-Linked 2D COFs

Solid phase adsorbents with high removal affinity for per- and polyfluoroalkyl substances (PFAS) in aqueous environments are sought. We report the synthesis and investigation of COF-I, a new covalent organic framework (COF) with a good affinity for PFAS adsorption. COF-I was synthesized by the condensation reaction between 2,4,6-trimethyl-1,3,5-triazine and 2,3-dimethoxyterephthaldehyde and fully characterized. In addition to the high crystallinity and surface area, COF-I showed high hydrolytic and thermal stability. Further, we converted its hydrophobic surface to a hydrophilic surface by converting the ortho-methoxy groups to hydroxyl derivatives and produced a new hydrophilic olefin-linked two-dimensional (2D) COF. We experimentally measured the crystallinity of both COFs by X-ray diffraction and used atomistic simulations coupled with cross-polarization/magic angle spinning solid-state nuclear magnetic resonance (CP/MAS ssNMR) to determine the relative amounts of AA-stacking and AB-stacking present. COF-I, with its hydrophobic surface and methoxy groups in the ortho positions, showed the best PFAS adsorption. COF-I reduced the concentration of perfluorooctanoic acid from 20 to 0.069 μg L-1 and to 0.052 μg L-1 for perfluorooctanesulfonic acid. These amounts are lower than the U.S. Environmental Protection Agency advisory level (0.070 μg L-1). High efficiency, fast kinetic adsorption, and reusability of COF-I are advantages of COF-I for PFAS removal from water.

Removing polyfluoroalkyl substances (PFAS) from wastewater with mixed matrix membranes

Polyfluoroalkyl and perfluoroalkyl (PFAS) chemicals are fluorinated and exhibit complicated behavior. They are determined and highly resistant to ecological modifications that render plants ecologically robust. Thermal stability and water and oil resistance are examples of material qualities. Their adverse consequences are causing increasing worry due to their bioaccumulative nature in humans and other creatures. Direct data indicates that PFAS exposure in humans causes endocrine system disruption, immune system suppression, obesity, increased cholesterol, and cancer. Several PFASs are present in drinking water at low doses and may harm people. These cancer-causing PFAS have caused concern for water bodies all around the globe. Analytical techniques are used to identify and measure PFAS in an aqueous medium (membrane). Furthermore, a deeper explanation is provided for PFAS removal methods, including mixed matrix membrane (MMM) technology. By removing over 99 % of the PFAS from wastewater, MMMs may effectively remove PFAS from sewage when the support matrix contains adsorbing components. Furthermore, we consider several factors affecting the removal of PFAS and practical sorption methods for PFAS onto various adsorbents.

Surface modifications of biopolymers for removal of per- and polyfluoroalkyl substances from water: Current research and perspectives

Per- and polyfluoroalkyl substances (PFAS) are highly recalcitrant organic contaminants that have attracted ever-increasing attention from the general public, government agencies and scientific communities. To remove PFAS from water, especially the enormous volume of drinking water, stormwater, and groundwater, sorption is the most practical approach. Success of this approach demands green, renewable, and sustainable materials for capturing PFAS at ng/L or µg/L levels. To meet this demand, this manuscript critically reviewed sorbents developed from biopolymers, such as chitosan (CTN), alginate (ALG), and cellulose (CEL) covering the period from 2008 to 2023. The use of different cross-linkers for the surface modifications of biopolymers were described. The underlying removal mechanism of biosorbents for PFAS adsorption from molecular perspectives was discussed. Besides reviewing and comparing the performance of different bio-based sorbents with respect to environmental factors like pH, and sorption kinetics and capacity, strategies for modifying biosorbents for better performance were proposed. Additionally, approaches for regeneration and reuse of the biosorbents were discussed. This was followed by further discussion of challenges facing the development of biosorbents for PFAS removal.

Adsorption of per- and polyfluoroalkyl substances (PFAS) by ionic liquid-modified clays: Effect of clay composition and PFAS structure

Organically modified clays have been reported as a promising class of adsorbents for the treatment of per- and polyfluoroalkyl substances (PFAS), a group of emerging contaminants of widespread concerns. Here, we reported the development and evaluation of ionic liquid (IL)-modified clays prepared with various natural clays to explore the role of clay substrate in the adsorption of eight persistent perfluoroalkyl acids (PFAAs). Based on detailed adsorption isotherm study, we found that the adsorption capacities of PFAAs were closely related to the cation exchange capacities of the raw clays and correspondingly the IL loadings of the modified clays. Additionally, a positive correlation was observed between the adsorption affinity of PFAAs onto IL-modified clays and the octanol-water distribution coefficient (Dow) of PFAAs. Adsorption free energy analysis suggested that both electrostatic and hydrophobic interactions played important roles in the adsorption of PFAAs onto IL-modified clays. Although electrostatic interactions were more predominant, the contribution of hydrophobic interactions increased with the increasing carbon number of perfluoroalkyl moiety of PFAAs, resulting in more favorable adsorption of long-chain PFAAs than their short-chain homologs. The performance of IL-modified clays was further demonstrated for the removal of PFAA mixtures under environmentally relevant conditions. Overall, results of this work can provide important insights into guiding the design of organically modified clay adsorbents for PFAS treatment.

A critical review of perfluoroalkyl and polyfluoroalkyl substances (PFAS) landfill disposal in the United States

Landfills manage materials containing per- and polyfluoroalkyl substances (PFAS) from municipal solid waste (MSW) and other waste streams. This manuscript summarizes state and federal initiatives and critically reviews peer-reviewed literature to define best practices for managing these wastes and identify data gaps to guide future research. The objective is to inform stakeholders about waste-derived PFAS disposed of in landfills, PFAS emissions, and the potential for related environmental impacts. Furthermore, this document highlights data gaps and uncertainties concerning the fate of PFAS during landfill disposal. Most studies on this topic measured PFAS in liquid landfill effluent (leachate); comparatively fewer have attempted to estimate PFAS loading in landfills or other effluent streams such as landfill gas (LFG). In all media, the reported total PFAS heavily depends on waste types and the number of PFAS included in the analytical method. Early studies which only measured a small number of PFAS, predominantly perfluoroalkyl acids (PFAAs), likely report a significant underestimation of total PFAS. Major findings include relationships between PFAS effluent and landfill conditions - biodegradable waste increases PFAS transformation and leaching. Based on the results of multiple studies, it is estimated that 84% of PFAS loading to MSW landfills (7.2 T total) remains in the waste mass, while 5% leaves via LFG and 11% via leachate on an annual basis. The environmental impact of landfill-derived PFAS has been well-documented. Additional research is needed on PFAS in landfilled construction and demolition debris, hazardous, and industrial waste in the US.

Physicochemical properties and interactions of perfluoroalkyl substances (PFAS) - Challenges and opportunities in sensing and remediation

Per- and polyfluoroalkyl substances (PFAS) is a class of persistent organic pollutants that presents health and environmental risks. PFAS are ubiquitously present in the environment, but current remediation technologies are ineffective in degrading them into innocuous chemicals, especially high energy degradation processes often generate toxic short chain intermediates. Therefore, the best remediation strategy is to first detect the source of pollution, followed by capturing and mineralising or recycling of the compounds. The main objective of this article is to summarise the unique physicochemical properties and to critically review the intermolecular and intramolecular physicochemical interactions of PFAS, and how these interactions can become obstacles; and at the same time, how they can be applied to the PFAS sensing, capturing, and recycling process. The physicochemical interactions of PFAS chemicals are being reviewed in this paper includes, (1) fluorophilic interactions, (2) hydrophobic interactions, (3) electrostatic interactions and cation bridging, (4) ionic exchange and (5) hydrogen bond. Moreover, all the different influential factors to these interactions have also been reported. Finally, properties of these interactions are compared against one another, and the recommendations for future designs of affinity materials for PFAS have been given.

Enhancement of adsorption efficiency of crystal violet and chlorpyrifos onto pectin hydrogel@Fe3O4-bentonite as a versatile nanoadsorbent

The magnetic mesoporous hydrogel-based nanoadsornet was prepared by adding the ex situ prepared Fe₃O₄ magnetic nanoparticles (MNPs) and bentonite clay into the three-dimentional (3D) cross-linked pectin hydrogel substrate for the adsorption of organophosphorus chlorpyrifos (CPF) pesticide and crystal violet (CV) organic dye. Different analytical methods were utilized to confirm the structural features. Based on the obtained data, the zeta potential of the nanoadsorbent in deionized water with a pH of 7 was - 34.1 mV, and the surface area was measured to be 68.90 m²/g. The prepared hydrogel nanoadsorbent novelty owes to possessing a reactive functional group containing a heteroatom, a porous and cross-linked structure that aids convenient contaminants molecules diffusion and interactions between the nanoadsorbent and contaminants, viz., CPF and CV. The main driving forces in the adsorption by the Pectin hydrogel@Fe₃O₄-bentonite adsorbent are electrostatic and hydrogen-bond interactions, which resulted in a great adsorption capacity. To determine optimum adsorption conditions, effective factors on the adsorption capacity of the CV and CPF, including solution pH, adsorbent dosage, contact time, and initial concentration of pollutants, have been experimentally investigated. Thus, in optimum conditions, i.e., contact time (20 and 15 min), pH 7 and 8, adsorbent dosage (0.005 g), initial concentration (50 mg/L), T (298 K) for CPF and CV, respectively, the CPF and CV adsorption capacity were 833.333 mg/g and 909.091 mg/g. The prepared pectin hydrogel@Fe₃O₄-bentonite magnetic nanoadsorbent presented high porosity, enhanced surface area, and numerous reactive sites and was prepared using inexpensive and available materials. Moreover, the Freundlich isotherm has described the adsorption procedure, and the pseudo-second-order model explained the adsorption kinetics. The prepared novel nanoadsorbent was magnetically isolated and reused for three successive adsorption-desorption runs without a specific reduction in the adsorption efficiency. Therefore, the pectin hydrogel@Fe₃O₄-bentonite magnetic nanoadsorbent is a promising adsorption system for eliminating organophosphorus pesticides and organic dyes due to its remarkable adsorption capacity amounts.

Microbial and thermal treatment techniques for degradation of PFAS in biosolids: A focus on degradation mechanisms and pathways

Per- and polyfluoroalkyl substances (PFAS) are persistent organic chemicals detected in biosolids worldwide, which have become a significant concern for biosolids applications due to their increasing environmental risks. Hence, it is pivotal to understand the magnitude of PFAS contamination in biosolids and implement effective technologies to reduce their contamination and prevent hazardous aftermaths. Thermal techniques such as pyrolysis, incineration and gasification, and biodegradation have been regarded as impactful solutions to degrade PFAS and transform biosolids into value-added products like biochar. These techniques can mineralize PFAS compounds under specific operating parameters, which can lead to unique degradation mechanisms and pathways. Understanding PFAS degradation mechanisms can pave the way to design the technology and to optimize the process conditions. Therefore, in this review, we aim to review and compare PFAS degradation mechanisms in thermal treatment like pyrolysis, incineration, gasification, smouldering combustion, hydrothermal liquefaction (HTL), and biodegradation. For instance, in biodegradation of perfluorooctane sulfonic acid (PFOS), firstly C-S bond cleavage occurs which is followed by hydroxylation, decarboxylation and defluorination reactions to form perfluoroheptanoic acid. In HTL, PFOS degradation is carried through OH^-catalyzed series of nucleophilic substitution and decarboxylation reactions. In contrast, thermal PFOS degradation involves a three-step random-chain scission pathway. The first step includes C-S bond cleavage, followed by defluorination of perfluoroalkyl radical, and radical chain propagation reactions. Finally, the termination of chain propagation reactions produces very short-fluorinated units. We also highlighted important policies and strategies employed worldwide to curb PFAS contamination in biosolids.

Influence of grain size, organic carbon and organic matter residue content on the sorption of per- and polyfluoroalkyl substances in aqueous film forming foam contaminated soils - Implications for remediation using soil washing

A soil that was historically contaminated with Aqueous Film Forming Foam (AFFF) was dry sieved into size fractions representative of those produced during soil washing. Batch sorption tests were then conducted to investigate the effect of soil parameters on in situ per- and polyfluoroalkyl substances (PFAS) sorption of these different size fractions: < 0.063 mm, 0.063 to 0.5 mm, 0.5 to 2 mm, 2 to 4 mm, 4 to 8 mm, and soil organic matter residues (SOMR). PFOS (513 ng/g), 6:2 FTS (132 ng/g) and PFHxS (58 ng/g) were the most dominant PFAS in the AFFF contaminated soil. Non-spiked, in situ K_d values for 19 PFAS ranged from 0.2 to 138 L/Kg (log K_d -0.8 to 2.14) for the bulk soil and were dependant on the head group and perfluorinated chain length (spanning C₄ to C₁₃). The K_d values increased with decreasing grain size and increasing organic carbon content (OC), which were correlated to each other. For example, the PFOS K_d value for silt and clay (< 0.063 mm, 17.1 L/Kg, log K_d 1.23) were approximately 30 times higher compared to the gravel fraction (4 to 8 mm, 0.6 L/Kg, log K_d -0.25). The highest PFOS K_d value (116.6 L/Kg, log K_d 2.07) was found for the SOMR fraction, which had the highest OC content. K_oc values for PFOS ranged from 6.9 L/Kg (log K_oc 0.84) for the gravel fraction to 1906 L/Kg (log K_oc 3.28) for the silt and clay, indicating that the mineral composition of the different size fractions also influenced sorption. The results here emphasize the need to separate coarse-grained fractions and fine-grained fractions, and in particular the SOMR, to optimize the soil washing process. Higher K_d values for the smaller size fractions indicate that coarser soils are better suited for soil washing.

Surface-modified biopolymers for removing mixtures of per- and polyfluoroalkyl substances from water: Screening and removal mechanisms

Green, renewable, and sustainable materials are needed for removing per- and polyfluoroalkyl substances (PFASs) in water. Herein, we synthesized and tested alginate (ALG) and chitosan (CTN) based and polyethyleneimine (PEI) functionalized fibers/aerogels for the adsorption of mixtures of 12 PFASs (9 short- and long-chain PFAAs, GenX, and 2 precursors) from water at an initial concentration of 10 μg/L each. Out of 11 biosorbents, ALGPEI-3 and GTH CTNPEI aerogels had the best sorption performance. Through detailed characterization of the sorbents before and after PFASs sorption, it was revealed that hydrophobic interaction was the dominant mechanism controlling PFASs sorption while electrostatic interactions played a minor role. As a result, both aerogels had fast and superior sorption of relatively hydrophobic PFASs from pH 2 to 10. Even at extreme pH conditions, the aerogels retained their shape perfectly. Based upon the isotherms, the maximum adsorption capacity of ALGPEI-3 and GTH-CTNPEI aerogels towards total PFASs removal was 3045 and 12,133 mg/g, respectively. Although the sorption performance of the GTH-CTNPEI aerogel toward short chain PFAS was less than satisfactory and varied between 70 and 90% in 24 h, it may find its use in removing relatively hydrophobic PFAS at high concentrations in complex and extreme environments.

Synthesis and characterization of PCN-222 metal organic framework and its application for removing perfluorooctane sulfonate from water

Poly- and perfluoro alkyl substances (PFAS) are a group of man-made, notoriously persistent, and highly toxic contaminants in the environment reported worldwide. Many adsorbents including granular activated carbon, graphene, biochar, zeolites, and clay minerals have been tested for PFAS removal from water, but most of these materials suffer from high cost and/or poor removal performance. Here, we synthesized, characterized, and examined the efficiency of PCN-222(Fe), a new porous metal organic framework (MOF) with high water stability, for adsorptive removal of a frequently occurring PFAS, perfluorooctane sulfonate (PFOS), from water. The adsorption isotherm and kinetic studies revealed high PFOS adsorption capacity of PCN-222 (2257 mg/g), with rapid PFOS removal rate (within 30 min). The structure of PCN-222 was unaffected in water in the pH range of 2-10 but disintegrated and lost its PFOS removal ability at pH > 10. The PFOS adsorption on PCN-222 was an endothermic reaction. Electrostatic attraction was a dominant mechanism for PFOS adsorption at < 1694 mg/g PFOS concentration, while hydrophobic interaction accompanied with hydrogen-bonding was responsible at ≥ 1694 mg/g PFOS concentration. The interlayer morphology of PCN-222 did not change due to increasing PFOS loading. The findings of this study demonstrated superior features of PCN-222 over other conventional adsorbents for its potential application in removing PFOS from contaminated water to reduce PFOS transfer from water to living organisms.

A mechanistic insight into the shrinkage and swelling of Ca-montmorillonite upon adsorption of chain-like ranitidine in an aqueous system

Adsorption behavior of ranitidine hydrochloride (RT) on a Ca-montmorillonite (SAz-1) was studied in aqueous system through batch experiments. The adsorption kinetics revealed that the equilibrium reached within 0.25 h and the data fitted well to the pseudo-second order kinetic equation (R² = 0.98). The maximum RT adsorption capacity of SAz-1 was 369.2 mg/g and the adsorption isotherm data followed the Langmuir model (R² = 0.99). The adsorption of RT and desorption of exchangeable cations from the clay mineral were linearly correlated, suggesting that cation exchange was the dominant mechanism of RT adsorption. The XRD examination of RT-adsorbed SAz-1 samples (unsaturated/saturated) after heating enabled the calculation of RT occupied area in the interlayer of the clay mineral. The results suggested that adsorbed-RT at low loading rate could lay on the internal surfaces in a free style to reduce the basal spacing (d₀₀₁ value) of SAz-1. When the RT loading rate was increased, a limited surface space enforced more RT molecules to lay in a tilted style and caused interlayer swelling of SAz-1 increasing the d₀₀₁ value. The trend of rising decomposition temperature of RT with increasing RT loading rates confirmed intercalation of RT molecules in SAz-1. Infrared spectral analysis revealed the participation of amide and furan groups of RT in binding between RT and SAz-1. Thus, this study indicated that SAz-1 is an efficient adsorbent to remove RT from contaminated water, and the chain-like molecular structure of RT could cause an irregular change in the basal spacing of swelling type clay minerals.

Sorptive removal of per- and polyfluoroalkyl substances from aqueous solution: Enhanced sorption, challenges and perspectives

Per- and polyfluoroalkyl substances (PFASs) have garnered attention globally given their ubiquitous occurrence, toxicity, bioaccumulative potential, and environmental persistence. Sorption is widely used to remove PFASs given its simplicity and cost-effectiveness. This article reviews recently fabricated sorbents, including carbon materials, minerals, polymers, and composite materials. The characteristics and interactions of the sorbents with PFASs are discussed to better understand sorptive processes. Various sorbents have exhibited high removal rates for legacy perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS). Novel polymers with special design better remove long- and short-chain PFASs than other sorbents. Although hydrophobic and electrostatic interactions mainly drive the sorption of anionic, cationic, and zwitterionic PFASs, enhancing PFAS sorption on designed sorbents has mainly depended on improving electrostatic interactions. Pearson correlation analysis showed that PFOS sorption capacity of sorbents is positively correlated with their specific surface area. Newly discovered pathways, including the air-water interfacial adsorption, F-F fluorophilic interactions, and (hemi) micelle formation, can enhance PFAS sorption to a certain extent. In addition to PFOA and PFOS, the sorption of emerging PFASs, including aqueous film-forming foam-relevant PFASs, constitutes a new research direction. The functionalization methods for enhancing PFAS sorption and challenges of PFAS sorption are also discussed to provide scope for future research. The discussions herein may contribute to developing efficient sorption technologies to remove PFASs.

Recent advances in the remediation of perfluoroalkylated and polyfluoroalkylated contaminated sites

Per- and polyfluoroalkyl substances (PFASs) are compounds used since 1940 in various formulations in the industrial and consumer sectors due to their high chemical and thermal stability. In recent years, PFASs have caused global concern due to their presence in different water and soil matrices, which threatens the environment and human health. These compounds have been reported to be linked to the development of serious human diseases, including but not limited to cancer. For this reason, PFASs have been considered as persistent organic compounds (COPs) and contaminants of emerging concern (CECs). Therefore, this work aims to present the advances in remediation of PFASs-contaminated soil and water by addressing the current literature. The performance and characteristics of each technique were addressed deeply in this work. The reviewed literature found that PFASs elimination studies in soil and water were carried out at a laboratory and pilot-scale in some cases. It was found that ball milling, chemical oxidation and thermal desorption are the most efficient techniques for the removal of PFASs in soils, however, phyto-microbial remediation is under study, which claims to be a promising technique. For the remediation of PFASs-contaminated water, the processes of electrocoagulation, membrane filtration, ozofractionation, catalysis, oxidation reactions - reduction, thermolysis and destructive treatments with plasma have presented the best results. It is noteworthy that hybrid treatments have also proved to be efficient techniques in the removal of these contaminants from soil and water matrices. Therefore, the improvisation and implication of existing techniques on a field-scale are greatly warranted to corroborate the yields obtained on a pilot- and laboratory-scale.

Poly- and Perfluoroalkyl Substances (PFAS) in Landfills: Occurrence, Transformation and Treatment

Landfills have served as the final repository for > 50 % municipal solid wastes in the United States. Because of their widespread uses and persistence in the environment, per- and polyfluoroalkyl substances (PFAS) (>4000 on the global market) are ubiquitously present in everyday consumer, commercial and industrial products, and have been widely detected in both closed (tens ng/L) and active (thousands to ten thousands ng/L) landfills due to disposal of PFAS-containing materials. Along with the decomposition of wastes in-place, PFAS can be transformed and released from the wastes into leachate and landfill gas. Consequently, it is critical to understand the occurrence and transformation of PFAS in landfills and the effectiveness of landfills, as a disposal alternative, for long-term containment of PFAS. This article presents a state-of-the-art review on the occurrence and transformation of PFAS in landfills, and possible effect of PFAS on the integrity of modern liner systems. Based on the data published from 10 countries (250 + landfills), C4-C7 perfluoroalkyl carboxylic acids were found predominant in the untreated landfill leachate and neutral PFAS, primarily fluorotelomer alcohols, in landfill air. The effectiveness and limitations of the conventional leachate treatment technologies and emerging technologies were also evaluated to address PFAS released into the leachate. Among conventional technologies, reverse osmosis (RO) may achieve a high removal efficiency of 90-100 % based on full-scale data, which, however, is vulnerable to the organic fouling and requires additional disposal of the concentrate. Implications of these knowledge on PFAS management at landfills are discussed and major knowledge gaps are identified.

Pollutant source or sink? Adsorption and mobilization of PFOS and PFOA from sediments in a large shallow lake with extended reed belt

In this study, we i) assessed the occurrence of perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) in sediments, pore water, and bulk water from three different areas in Lake Neusiedl, Austria, and ii) investigated mechanisms regulating adsorption and remobilization of these substances under different conditions via multiple lab-scale experiments. The adsorption capacity was mainly influenced by sediments' organic matter content, oxide composition, and pre-loading. Results suggest that a further increase of PFAS-concentrations in the open lake can be partly buffered by sediment transport to the littoral zone and adsorption to sediments in the extended reed belt. But, under current conditions, the conducted experiments revealed a real risk for mobilization of PFOS and PFOA from reed belt sediments that may lead to their transport back into the lake. The amount of desorbed PFAS is primarily dependent on water/sediment- or pore water/water-ratios and the concentration gradient. In contrast, water matrix characteristics and oxygen levels played a minor role in partitioning. The highest risk for remobilizing PFOS and PFOA was observed in experiments with sediments taken near the only major tributary to the lake (river Wulka), which had the highest pre-loading. The following management advice for water transport between high and low polluted areas can be derived based on the results. First, to reduce emissions into Lake waters from polluted tributaries like the Wulka river, we recommend diffuse pathways through the reed belt in the lake's littoral to reduce pollutant transport into the Lake and avoid high local sediment loadings. Second, water exchange with dried-up areas with probable higher loadings should be carefully handled and monitored to avoid critical back transport in the open lake. And third, general work in the reed belt or generally in the reed should be accompanied by monitoring to prevent uncontrolled remobilization in the future.

PFOS Mass Flux Reduction/Mass Removal: Impacts of a Lower-Permeability Sand Lens within Otherwise Homogeneous Systems

Perfluorooctane sulfonic acid (PFOS) is one of the most common per- and polyfluoroalkyl substances (PFAS) and is a significant risk driver for these emerging contaminants of concern. A series of two-dimensional flow cell experiments was conducted to investigate the impact of flow field heterogeneity on the transport, attenuation, and mass removal of PFOS. A simplified model heterogeneous system was employed consisting of a lower-permeability fine sand lens placed within a higher-permeability coarse sand matrix. Three nonreactive tracers with different aqueous diffusion coefficients, sodium chloride, pentafluorobenzoic acid, and β-cyclodextrin, were used to characterize the influence of diffusive mass transfer on transport and for comparison to PFOS results. The results confirm that the attenuation and subsequent mass removal of the nonreactive tracers and PFOS were influenced by mass transfer between the hydraulically less accessible zone and the coarser matrix (i.e., back diffusion). A mathematical model was used to simulate flow and transport, with the values for all input parameters determined independently. The model predictions provided good matches to the measured breakthrough curves, as well as to plots of reductions in mass flux as a function of mass removed. These results reveal the importance of molecular diffusion and pore water velocity variability even for systems with relatively minor hydraulic conductivity heterogeneity. The impacts of the diffusive mass transfer limitation were quantified using an empirical function relating reductions in contaminant mass flux (MFR) to mass removal (MR). Multi-step regression was used to quantify the nonlinear, multi-stage MFR/MR behavior observed for the heterogeneous experiments. The MFR/MR function adequately reproduced the measured data, which suggests that the MFR/MR approach can be used to evaluate PFOS removal from heterogeneous media.

One-Step Synthesis of a Mn-Doped Fe2O3/GO Core-Shell Nanocomposite and Its Application for the Adsorption of Levofloxacin in Aqueous Solution

This study describes for the first time the synthesis, characterization, and application of a MnFe₂O₃/GO core-shell nanocomposite as an adsorbent for the removal of levofloxacin (Lev) from real water samples. The formation of the proposed nanocomposite was confirmed using various characterization techniques. The structural techniques revealed a 20 nm average particle size of the MnFe₂O₃/GO core-shell nanocomposite, with a surface area of 70.7 m² g^-1, as shown by the BET results. The most influential parameters (adsorbent dosage, stirring rate, and Lev pH) that affected the adsorption process were optimized using the response surface methodology (RSM) based on a central composite design. The optimum conditions were 0.007 g, 2, and 7 for adsorbent dosage, stirring rate, and Lev pH, respectively. The adsorption behavior of Lev on the MnFe₂O₃/GO core-shell nanocomposite was examined using isotherm models, kinetics, and thermodynamics. The kinetic models demonstrated that the adsorption process was controlled by both intraparticle and outer diffusion. Furthermore, the results obtained revealed that the adsorption of Lev on MnFe₂O₃/GO was dominated by electrostatic interactions. Moreover, Dubinin-Radushkevich and Temkin isotherms confirmed that the sorption mechanism was dominated by electrostatic interactions, while Langmuir and Sips models confirmed a monolayer adsorption process. The maximum adsorption capacity of Lev onto the MnFe₂O₃/GO adsorbent was found to be 129.9 mg g^-1. Furthermore, the thermodynamic data revealed that the adsorption system was spontaneous and exothermic. The synthesized MnFe₂O₃/GO core-shell nanocomposite showed significant recyclability and regenerability properties up to five adsorption-desorption cycles. As a proof of concept, the performance of the prepared adsorbent was evaluated for laboratory-scale purification of spiked real water samples. The prepared adsorbent significantly reduced the concentration of Lev in the real water samples and the removal efficiency ranged from 86 to 97%.

Ecotoxicological effects of per- and polyfluoroalkyl substances (PFAS) and of a new PFAS adsorbing organoclay to immobilize PFAS in soils on earthworms and plants

A novel adsorptive organoclay (Intraplex A®) was developed for the in situ immobilization of per- and polyfluoroalkyl substances (PFAS) in the vadose zone. We provide the first evaluation of the effects of Intraplex A® on earthworms and plants in a PFAS-contaminated soil. Ecotoxicological tests were carried out on control soil with and without Intraplex A® (C + I and C, respectively) and PFAS-contaminated soil with and without Intraplex A® (PFAS + I and PFAS, respectively). We investigated the acute ecotoxicological effects of PFAS and Intraplex A® on the growth, reproduction and survival of earthworms (Eisenia fetida) and on plant growth (oat - Avena sativa and turnip - Brassica rapa L. silvestris). Earthworm lethality was 7.6 lower in PFAS + I than in PFAS soil. Earthworms avoided 100% C + I and PFAS + I soils, and reduced earthworms' reproduction was observed in both these soils. For both plant species, the PFAS + I soil yielded less fresh and dry shoot biomass than the PFAS soil, while root growth remained unaffected (all tests: p < 0.05). Soils with Intraplex A® had some negative effects on plants and earthworms, which must be balanced with its benefits as an in situ PFAS adsorbent.

Adsorption, Structure, and Dynamics of Short- and Long-Chain PFAS Molecules in Kaolinite: Molecular-Level Insights

The ubiquitous presence of poly- and perfluoroalkyl substances (PFAS) in different natural settings poses a serious threat to environmental and human health. Soils and sediments represent one of the important exposure pathways of PFAS for humans and animals. With increasing bioaccumulation and mobility, it is extremely important to understand the interactions of PFAS molecules with the dominant constituents of soils such as clay minerals. This study reports for the first time the fundamental molecular-level insights into the adsorption, interfacial structure, and dynamics of short- and long-chain PFAS molecules at the water-saturated mesopores of kaolinite clay using classical molecular dynamics (MD) simulations. At environmental conditions, all the PFAS molecules are exclusively adsorbed near the hydroxyl surface of the kaolinite, irrespective of the terminal functional groups and metal cations. The interfacial adsorption structures and coordination environments of PFAS are strongly dependent on the nature of the functional groups and their hydrophobic chain length. The formation of large, aggregated clusters of long-chain PFAS at the hydroxyl surface of kaolinite is responsible for their restricted dynamics in comparison to short-chain PFAS molecules. Such comprehensive knowledge of PFAS at the clay mineral interface is critical to developing novel site-specific degradation and mitigation strategies.

A dual grafted fluorinated hydrocarbon amine weak anion exchange resin polymer for adsorption of perfluorooctanoic acid from water

Perfluorooctanoic acid (PFOA) is a persistent and recalcitrant organic contaminant of exceptional environmental concern, and its removal from water has increasingly attracted global attention due to its wide distribution and strong bioaccumulation. Adsorption is considered an effective technique for PFOA removal and more efficient PFOA sorbents are still of interest. This study developed a dual grafted fluorinated hydrocarbon amine weak anion exchange (WAX) polymeric resin (Sepra-WAX-KelF-PEI) for PFOA removal from water. This polymer was synthesized by a two-step amine grafting reaction procedure involving first the reaction of the Sepra-WAX hydrocarbon polymer with poly(vinylidinefluoride-chlorotrifluoroethylene) (Kel-F 800) and then a second reaction with polyethyleneimine (PEI). Characterization of the synthesized polymers was performed using scanning electron microscopy and elemental analysis (F and Cl) by energy dispersive X-ray spectroscopy. The PFOA adsorption performance evaluations were conducted by packed column flow analyses with on-line detection. The results show the breakthrough of the Sepra-WAX-KelF-PEI synthesized with optimum stoichiometry was two times better than the starting anion exchange polymer Sepra-WAX, and six times better than powdered activated carbon, when using the same column size. The adsorption mechanisms of this novel adsorbent including hydrophobic interaction and electrostatic interaction were also clarified in this study. The adsorption kinetic parameters of the two optimum synthesized sorbents were determined using the Thomas model, the Yoon-Nelson model, and batch isotherm studies, and compared with those found with activated carbon and the starting WAX resin. Good agreement of the batch isotherm and column studies with respect to adsorption capacities trends between all three polymers (Sepra-WAX, Sepra-WAX-KelF, and Sepra-WAX-KelF-PEI) were noted.