Interfacial tension and phase behavior of surfactant-brine–oil system

Advance of Microemulsion and Application for Enhanced Oil Recovery

With the ongoing advancement in oil exploration, microemulsion, as an innovative oil displacement method, has garnered considerable attention owing to its exceptional physicochemical properties in enhancing crude oil recovery. As such, this study initially delineates the fundamental concepts, classifications, formation mechanisms, advantages, and preparation methodologies of microemulsions. Subsequently, it introduces the selection criteria for microemulsion components, followed by an elucidation of the characterization methods for microemulsions based on these criteria. Furthermore, it examines the factors influencing the efficacy of microemulsions in enhancing oil recovery through two distinct methods, along with the effects of various formulation microemulsions under laboratory and oilfield conditions. Additionally, it outlines prospects, challenges, and future development trends pertaining to microemulsions.

Dynamic Interfacial Tensions of Surfactant and Polymer Solutions Related to High-Temperature and High-Salinity Reservoir

Betaine is a new surfactant with good application prospects in high-temperature and high-salinity reservoirs. The interfacial properties of two kinds of betaine mixtures with a good synergistic effect were evaluated in this paper. On this basis, the effects of temperature-resistant, salt-resistant polymers with different contents of 2-acrylamide-2-methylpropanesulfonic acid (AMPS) on dynamic interfacial tensions (IFTs) against n-alkanes and crude oil were studied. The experimental results show that the IFTs between betaine ASB and n-alkanes can be reduced to ultra-low values by compounding with anionic surfactant petroleum sulfonate (PS) and extended anionic surfactant alkoxyethylene carboxylate (AEC), respectively. ASB@AEC is very oil-soluble with n_min value ≥14, and ASB@PS is relatively water-soluble with n_min value of 10. The water solubility of both ASB@PS and ASB@AEC is enhanced by the addition of water-soluble polymers. The HLB of the ASB@AEC solution becomes better against crude oil after the addition of polymers, and the IFT decreases to an ultra-low value as a result. On the contrary, the antagonistic effect in reducing the IFT can be observed for ASB@PS in the same case. In a word, polymers affect the IFTs of surfactant solutions by regulating the HLB.

Comprehensive review of the interfacial behavior of water/oil/surfactant systems using dissipative particle dynamics simulation

A comprehensive understanding of interfacial behavior in water/oil/surfactant systems is critical to evaluating the performance of emulsions in various industries, specifically in the oil and gas industry. To gain fundamental knowledge regarding this interfacial behavior, atomistic methods, e.g., molecular dynamics (MD) simulation, can be employed; however, MD simulation cannot handle phenomena that require more than a million atoms. The coarse-grained mesoscale methods were introduced to resolve this issue. One of the most effective mesoscale coarse-grained approaches for simulating colloidal systems is dissipative particle dynamics (DPD), which bridges the gap between macroscopic time and length scales and molecular-scale simulation. This work reviews the fundamentals of DPD simulation and its progress on colloids and interface systems, especially surfactant/water/oil mixtures. The effects of temperature, salt content, a water/oil ratio, a shear rate, and a type of surfactant on the interfacial behavior in water/oil/surfactant systems using DPD simulation are evaluated. In addition, the obtained results are also investigated through the lens of the chemistry of surfactants and emulsions. The outcome of this comprehensive review demonstrates the importance of DPD simulation in various processes with a focus on the colloidal and interfacial behavior of surfactants at water-oil interfaces.

Measurement of Interfacial Tension between Liquid Pb and a Molten LiCl-NaCl-KCl Mixture via a Floating Drop Method

The floating drop method has the potential for high-accuracy measurement of liquid–liquid interfacial tension. It was applied here to measure the interfacial tension between liquid Pb and a molten mixture of 8.9% LiCl, 50% NaCl, and KCl (mass%). The heavier Pb droplet floated on the lighter molten salt and enabled the acquisition of data at 673 K, 723 K, and 773 K under vacuum. The results agreed with previous reports. The temperature (T) dependence of the interfacial tension s was given by s = 459–1.27 T mN/m.

In situ micro-emulsification during surfactant enhanced oil recovery: A microfluidic study

HYPOTHESIS

It is generally believed that the improved efficiency of surfactant enhanced oil recovery (EOR) comes from ultra-low interfacial tension (IFT) between oil and surfactant solution owing to the formation of middle-phase microemulsion. However, hindered visibility in underground porous media prevents direct observation of in situ generation of middle-phase microemulsion during surfactant flooding. Thus, direct visualization of the process is vital, and could clarify its contribution to EOR.

EXPERIMENTS

Micro-emulsification of a displacing fluid containing sodium 4-dodecylbenzenesulfonate and alcohol propoxy sulfate with model oil was investigated. Phase diagrams were drawn using salinity scans, and the influence of polymer on emulsification was analyzed. Micro-emulsification was monitored through in situ fluorescent tagging via 2D-microfluidics and ex situ visualization via cryo-electron microscopy and small angle X-ray scattering. Its contribution to the oil recovery factor was quantified by measuring the volume of each phase in the eluates.

FINDINGS

On-chip experiments indicated that in situ micro-emulsification occurred when the prescreened surfactant solution flowed in contact with trapped oil. The aqueous phase initially invaded the residual oil, forming a low mobility microemulsion. This microemulsion was then diluted by subsequent displacing fluid, forming a new driving fluid that caused ultra-low IFT in the trapped oil downstream. Under the synergistic effect of micellar solubilization and trapped-oil mobilization, the recovery factor could be increased by up to 40% over waterflooding and 43% on polymer inclusion in the formulation.

Review on Amphiphilic Ionic Liquids as New Surfactants: From Fundamentals to Applications

The demand for lowering interfacial tension (IFT) in different processes has persuaded researchers to use stable and resistant surfactants with low environmental impact. For this purpose, surface-active ionic liquids (SAILs) have attracted much attention owing to their good amphiphilic nature and prominent properties like recyclability and high performance under harsh conditions. This review initially explains how the IFT and critical micelle concentration of different systems vary in the presence of different SAILs with a variety of alkyl chain lengths, head groups, and counter anions. Towards this aim, some physicochemical properties of SAILs as well as the corresponding theoretical aspects of adsorption are considered. Then, recent advances in utilizing SAILs for reducing IFT of different chemical systems are surveyed. Relevantly, the role of important operating parameters of temperature, pH, presence of electrolytes, and the chemical nature of involved phases are adequately discussed. Further, an overview of different SAILs applications in stabilization, separation, and in petroleum industries is scrutinized. To allow better judgment, precise comparisons between different types of SAILs and conventional surfactants are provided. Finally, challenges and possible directions of future research on SAILs are highlighted.

Bacteria Cell Hydrophobicity and Interfacial Properties Relationships: A New MEOR Approach

For microbial enhanced oil recovery (MEOR), different mechanisms have been introduced. In some of these papers, the phenomena and mechanisms related to biosurfactants produced by certain microorganisms were discussed, while others studied the direct impacts of the properties of microorganisms on the related mechanisms. However, there are only very few papers dealing with the direct impacts of microorganisms on interfacial properties. In the present work, the interfacial properties of three bacteria MJ02 (Bacillus Subtilis type), MJ03 (Pseudomonas Aeruginosa type), and RAG1 (Acinetobacter Calcoaceticus type) with the hydrophobicity factors 2, 34, and 79% were studied, along with their direct impact on the water/heptane interfacial tension (IFT), dilational interfacial visco-elasticity, and emulsion stability. A relationship between the adsorption dynamics and IFT reduction with the hydrophobicity of the bacteria cells is found. The cells with highest hydrophobicity (79%) exhibit a very fast dynamic of adsorption and lead to relatively large interfacial elasticity values at short adsorption time. The maximum elasticity values (at the studied frequencies) are observed for bacteria cells with the intermediate hydrophobicity factor (34%); however, at longer adsorption times. The emulsification studies show that among the three bacteria, just RAG1 provides a good capability to stabilize crude oil in brine emulsions, which correlates with the observed fast dynamics of adsorption and high elasticity values at short times. The salinity of the aqueous phase is also discussed as an important factor for the emulsion formation and stabilization.

The potential impact of using a surfactant and an alcoholic co-surfactant on SRB activity during EOR

Surfactants and co-surfactants play an important role in enhanced oil recovery for they improve petroleum solubility and reduce interfacial tensions between oil, water and the rock formation. Ethanol is receiving renewed attention as potential co-surfactant because of the negative results obtained with the use of salts and alkaline substances. Sulphate-reducing bacteria (SRB) can use surfactants and co-surfactants as carbon sources and, consequently, this can increase the biological accumulation of sulphide (souring). The aim of this research is to correlate SRB activity with different concentrations of co-surfactant (ethanol) as an attempt to quantifying in which concentration such compound can potentially increase or inhibit souring. The results show that the combination of surfactant (lauryl glucoside) and co-surfactant (ethanol) can increase SRB activity to about 2.3-fold. The highest sulphate consumption rate of 591 μg l^-1 h^-1 was observed in experiments with 0.03% and 1.5% (v/v) of surfactant and ethanol, respectively. The experiments indicated that SRB activity is only controlled by ethanol concentrations above 6.5% (v/v). Ethanol can potentially decrease costs with the use of biocides and significantly increase oil recovery ratios. Tests with the model Desulfovibrio vulgaris were not comparable with the results obtained with the SRB consortium.

Properties of Binary Surfactant Mixtures of Anionic Gemini Surfactant and Amphoteric Surfactant

The surface tension of the mixed system of linear alkylated diphenylmethane sulfonate and amphoteric surfactant didodecylmethylcarboxyl betaine along with their different combinations has been investigated in 0.1 M salt solutions at 313 K. The surface chemical parameters of the mixture were also calculated. The results show that the critical micelle concentration (CMC) and γCMC of the mixture are always lower than those of the individual surfactants, which indicates synergistic effects between the surfactant molecules. The interfacial tension of the Chinese Shengli crude oil and the connate water can be reduced to 5 × 10−3 mN · m−1 at 70°C with the mixture of alkylated diphenylmethane sulfonate and didodecylmethylcarboxyl betaine.

Investigation on the interfacial properties of a viscoelastic-based surfactant as an oil displacement agent recovered from fracturing flowback fluid

The utilization of a viscoelastic-based surfactant recovered from fracturing flowback fluid in chemical flooding was investigated in this paper.