Fabrication of three-dimensional porous β-cyclodextrin/chitosan functionalized graphene oxide hydrogel for methylene blue removal from aqueous solution

Hydrogels Based on Chitosan and Nanoparticles and Their Suitability for Dyes Adsorption from Aqueous Media: Assessment of the Last-Decade Progresses

Water is one of the fundamental resources for the existence of humans and the environment. Throughout time, due to urbanization, expanding population, increased agricultural production, and intense industrialization, significant pollution with persistent contaminants has been noted, placing the water quality in danger. As a consequence, different procedures and various technologies have been tested and used in order to ensure that water sources are safe for use. The adsorption process is often considered for wastewater treatment due to its straightforward design, low investment cost, availability, avoidance of additional chemicals, lack of undesirable byproducts, and demonstrated significant efficacious potential for treating and eliminating organic contaminants. To accomplish its application, the need to develop innovative materials has become an essential goal. In this context, an overview of recent advances in hydrogels based on chitosan and nanocomposites and their application for the depollution of wastewater contaminated with dyes is reported herein. The present review focuses on (i) the challenges raised by the synthesis process and characterization of the different hydrogels; (ii) the discussion of the impact of the main parameters affecting the adsorption process; (iii) the understanding of the adsorption isotherms, kinetics, and thermodynamic behavior; and (iv) the examination of the possibility of recycling and reusing the hydrogels.

Bioadsorbent nanocellulose aerogel efficiency impregnated with spent coffee grounds

Due to growing environmental concerns for better waste management, this study proposes developing a composite aerogel using cellulose nanofibers (CNF) and spent coffee grounds (SCG) through an eco-friendly method for efficient methylene blue (MB) adsorption. Adding SCG to the CNF aerogel altered the physical properties: it increases the volume (4.14 cm3 to 5.25 cm3) and density (0.018 to 0.022 g/cm3) but decrease the water adsorption capacity (2064 % to 1635 %). FTIR spectrum showed distinct functional groups in both all aerogels, showing hydroxyl, glyosidic bonds, and aromatic compounds. Additionally, SCG improved thermal stability of the aerogels. In term of adsorption efficacy, CNF-SCG40% aerogel as exceptionally well. According to Langmuir isotherm models, the adsorption of MB happened in a monolayer, with CNF-SCG40% showing a maximum adsorption capacity of 113.64 mg/g, surpassing CNF aerogel (58.82 mg/g). The study identified that the pseudo-second-order model effectively depicted the adsorption process, indicating a chemical-like interaction. This investigation successfully produced a single-use composite aerogel composed of CNF and SCG using an eco-friendly approach, efficiently adsorbing MB. By utilizing cost-effective materials and eco-friendly methods, this approach offers a sustainable solution for waste management, contributes to an eco-friendly industrial environment, and reduces production expenses and management costs.

Tuning the surface functionality of polyethylene glycol-modified graphene oxide/chitosan composite for efficient removal of dye

There has been a lot of attention on water pollution by dyes in recent years because of their serious toxicological implications on human health and the environment. Therefore, the current study presented a novel polyethylene glycol-functionalized graphene oxide/chitosan composite (PEG-GO/CS) to remove dyes from aqueous solutions. Several characterization techniques, such as SEM, TEM, FTIR, TGA/DTG, XRD, and XPS, were employed to correlate the structure-property relationship between the adsorption performance and PEG-GO/CS composites. Taguchi's (L25) approach was used to optimize the batch adsorption process variables [pH, contact time, adsorbent dose, and initial concentration of methyl orange (MO)] for maximal adsorption capacity. pH = 2, contact time = 90 min, adsorbent dose = 10 mg/10 mL, and MO initial concentration = 200 mg/L were found to be optimal. The material has a maximum adsorption capacity of 271 mg/g for MO at room temperature. With the greatest R2 = 0.8930 values, the Langmuir isotherm model was shown to be the most appropriate. Compared to the pseudo-first-order model (R2 = 0.9685), the pseudo-second-order model (R2 = 0.9707) better fits the kinetic data. Electrostatic interactions were the dominant mechanism underlying MO sorption onto the PEG/GO-CS composite. The as-synthesized composite was reusable for up to three adsorption cycles. Thus, the PEG/GO-CS composite fabricated through a simple procedure may remove MO and other similar organic dyes in real contaminated water.

Cost-effective one-spot hydrothermal synthesis of graphene oxide nanoparticles for wastewater remediation: AI-enhanced approach for transition metal oxides

This investigation presents a cost-efficient hydrothermal synthesis technique for producing graphene oxide nanoparticles (GO-NPs) that exhibit promising potential in wastewater treatment. The synthesis process involves a facile and expandable hydrothermal reactor that can be regulated using an AI-empowered methodology. The generated GO-NPs were characterised using X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, Raman spectroscopy, and transmission electron microscopy (TEM), confirming their successful synthesis and high quality. The high degree of crystallinity observed in the GO-NPs can be attributed to the favourable reaction conditions facilitated by the hydrothermal synthesis. The TEM analysis showed that the GO-NPs had a homogeneous dispersion pattern and a consistent size distribution of approximately 10 nm. Carboxylation was employed to functionalize the GO-NPs, enhancing their reactivity towards diverse contaminants present in wastewater. The remediation potential of the GO-NPs for transition metal oxides, which are frequently found in wastewater, was assessed. The GO-NPs exhibited notable efficacy in remediating the transition metal oxides that were subjected to testing. The heightened efficacy of remediation can be attributed to the substantial surface area and elevated reactivity of the GO-NPs, in addition to their functionalization using carboxylic groups. The cost-effective and efficient synthesis method, coupled with the high remediation potential of the GO-NPs, makes them a highly promising contender for employment in wastewater remediation applications. The use of AI in regulating the hydrothermal synthesis procedure enables accurate manipulation of the reaction parameters, thereby augmenting the quality and uniformity of the resultant GO-NPs. The proposed method exhibits scalability potential for large-scale production of GO-NPs, presenting a viable remedy for the challenges associated with wastewater remediation.

Chemical modification of β-cyclodextrin towards hydrogel formation

β-CD is a cyclic oligosaccharide, which has trunked cone like structure. The unique structure makes it efficient for numerous applications. Though, the native β-CD has many issues like low solubility, absence of sufficient functionalities and lower complexation ability with guest molecules. One of the most effective paths to increase the efficiency of cyclodextrins is the generation of polycyclodextrins. In this perspective article, we have summarized the recent reports on the synthetic methods towards the modification of β-CD. Besides, this article reviews the current improvements of two types of β-CD centered supramolecular hydrogels: one is supramolecular hydrogels prepared from CD-based poly(pseudo)rotaxanes and the other is supramolecular hydrogels developed through the host-guest interaction between small guest molecules and CDs. The Polycyclodextrins have established noteworthy applications in several areas ranging from adsorbents for organic pollutants removal to effective carriers of bioactive agents.

Animal sourced biopolymer for mitigating xenobiotics and hazardous materials

Over the past several decades, xenobiotic chemicals have badly affected the environment including human health, ecosystem and environment. Animal-sourced biopolymers have been employed for the removal of heavy metals and organic dyes from the contaminated soil and waste waters. Animal-sourced biopolymers are biocompatible, cost-effective, eco-friendly, and sustainable in nature which make them a favorable choice for the mitigation of xenobiotic and hazardous compounds. Chitin/chitosan, collagen, gelatin, keratin, and silk fibroin-based biopolymers are the most commonly used biopolymers. This chapter reviews the current challenge faced in applying these animal-based biopolymers in eliminating/neutralizing various recalcitrant chemicals and dyes from the environment. This chapter ends with the discussion on the recent advancements and future development in the employability of these biopolymers in such environmental applications.

Temperature-responsive graphene oxide/N-isopropylacrylamide/2-allylphenol nanocomposite for the removal of phenol and 2,4-dichlorophenol from aqueous solution

In this study, a novel thermo-responsive polymer was synthesized with efficient grafting of N-isopropylacrylamide as a thermosensitive polymer onto the graphene oxide surface for the efficient removal of phenol and 2,4-dichlorophenol from aqueous solutions. The synthesized polymer was conjugated with 2-allylphenol. Phenol and 2,4-dichlorophenol were monitored by ultra-performance liquid chromatography system equipped with a photodiode array detector. The nanoadsorbent was characterized by different techniques. The nanoadsorbent revealed high adsorption capacity where the removal percentages of 91 and 99% were found under optimal conditions for phenol and 2,4-dichlorophenol, respectively (for phenol; adsorbent dosage = 0.005 g, pH = 8, temperature= 25 °C, contact time = 60 min; for 2,4-dichlorophenol; adsorbent dosage = 0.005 g, pH = 5, temperature = 25 °C, contact time = 10 min). Adsorption of phenol and 2,4-dichlorophenol onto nanoadsorbent followed pseudo-second-order kinetic and Langmuir isotherm models, respectively. The values of ΔG (average value = - 11.39 kJ mol^-1 for phenol and 13.42 kJ mol^-1 for 2,4-dichlorophenol), ΔH (- 431.72 J mol^-1 for phenol and - 15,721.8 J mol^-1 for 2,4-dichlorophenol), and ΔS (35.39 J mol^-1 K^-1 for phenol and - 7.40 J mol^-1 K^-1 for 2,4-dichlorophenol) confirmed spontaneous and exothermic adsorption. The reusability study indicated that the adsorbent can be reused in the wastewater treatment application. Thermosensitive nanoadsorbent could be used as a low-cost and efficient sorbent for phenol and 2,4-dichlorophenol removal from wastewater samples.

Polymeric biomolecules based nanomaterials: Production strategies and pollutant mitigation as an emerging tool for environmental application

The ever-exploding global population coupled with its anthropogenic impact has imparted unparalleled detrimental effects on the environment and mitigating them has emerged as the prime challenge and focus of the current century. The niche of nanotechnology empowered by composites of biopolymers in the handling of xenobiotics and environmental clean-up has an unlimited scope. The appositeness of biopolymer-nanoparticles (Bp-NPs) for environmental contaminant mitigation has received unique consideration due to its exclusive combination of physicochemical characteristics and other attributes. The current review furnishes exhaustive scrutiny of the current accomplishments in the development of Bp-NPs and biopolymer nanomaterials (Bp-NMs) from various polymeric biomolecules. Special attention was provided for polymeric biomolecules such as cellulose, lignin, starch, chitin, and chitosan, whereas limited consideration on gelatin, alginate, and gum for the development of Bp-NPs and Bp-NMs; together with coverage of literature. Promising applications of tailored biopolymer hybrids such as Bp-NPs and Bp-NMs on environmentally hazardous xenobiotics handling and pollution management are discussed as to their notable environmental applications.

Construction of chitosan-based asymmetric antioxidant and anti-inflammatory repair film for acceleration of wound healing

Oxidative stress damage caused by free radicals around the moist microenvironment of wound has been a clinical challenge in skin tissue healing. Here, a novel chitosan-based bioinspired asymmetric wound repair composite (BAWRC) film was designed by facilitated endogenous tissue engineering strategy through layer-by-layer self-assembly technology for accelerated wound healing. The asymmetric characteristics were skillfully reflected by two different functional layers: hydrophilic chitosan (CS)/silk fibroin (SF) repair layer, and a hydrophobic bacteriostatic tea tree oil (TTO) layer with a rough surface. Simultaneously, sodium ascorbate (SA)-entrapped poly (lactic-co-glycolic acid) (PLGA) microspheres are distributed homogeneously in the hydrophilic layer to induce antioxidant response for skin repair. The distinctive asymmetric structure of BAWRC film endows it with synergistic effects, i.e., protects against the risk of infection from the external environment and facilitates deep skin wound healing. Results show that the minimum inhibition and bactericidal concentration of the BAWRC film were 1.25 and 6.25 mg/mL, respectively, demonstrating good antibacterial properties. The content of biofilm formation was significantly reduced when the concentration of TTO exceeds 5 mg/mL, indicating TTO shows a positive effect on bacteriostasis. In addition, the DPPH rates of BAWRC film were up to 64.7 % after incubation for 12 h, which was ascribed to that the release of SA and TTO as a natural product could accelerate free radical scavenging. The BAWRC film exhibited excellent biocompatibility, and good antibacterial capacity, enhancing adhesion and proliferation of the NIH3T3 cell in vitro, further facilitating the healing of a rat full-thickness skin wounds model. Herein, this versatile asymmetric film possesses great potential for clinical management of wound healing and related soft tissue regeneration.

Preparation and applications of chitosan and cellulose composite materials

Chitosan is a natural fiber, chemically cellulose-like biopolymer, which is processed from chitin. Its use as a natural polymer is getting more attention because it is non-toxic, renewable, and biocompatible. However, its poor mechanical and thermal strength, particle size, and surface area restrict its industrial use. Consequently, to improve these properties, cellulose and/or inorganic nanoparticles have been used. This review discusses the recent progress of chitosan and cellulose composite materials, their preparation, and their applications in different industrial sectors. It also discusses the modification of chitosan and cellulose composite materials to allow their use on a large scale. Finally, the recent development of chitosan composite materials for drug delivery, food packaging, protective coatings, and wastewater treatment are discussed. The challenges and perspectives for future research are also considered. This review suggests that chitosan and cellulose nano-composite are promising, low-cost products for environmental remediation involving a simple production process.

Graphene oxide-chitosan hydrogel for adsorptive removal of diclofenac from aqueous solution: preparation, characterization, kinetic and thermodynamic modelling

This work aimed at developing a natural compound-based hydrogel adsorbent to remove diclofenac as a model pharmaceutical from water. First, graphene oxide-chitosan (GO-CTS) and amine graphene oxide-chitosan (AGO-CTS) hydrogel adsorbents were synthesized via a facile mechanical mixing method. The synthesized materials were characterized through Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), scanning and transmission electron microscopy (SEM and TEM), Raman spectroscopy, and thermogravimetric analysis (TGA) techniques. In the second stage, adsorption experiments were conducted to determine the best GO to CTS ratio and find the optimized adsorption parameters, including the initial drug concentration, adsorbent dosage, pH, and temperature. The results showed that the optimal GO to CTS mass ratio is 2 : 5 and thus the same ratio was selected as the AGO to CTS mass ratio to understand the effect of amine-functionalization on removal efficiency. The optimal adsorption parameters were determined to be pH of 5, C _i of 100 ppm and dosage of 1.5 g L^-1, where 90.42% and 97.06% removal was achieved for optimal GO-CTS and AGO-CTS hydrogel adsorbents, respectively. Langmuir and Freundlich isotherms models were employed to investigate the adsorption behavior of diclofenac onto the synthesized hydrogels. The results revealed that the adsorption tends to be of the monolayer type and homogeneous, as the results were in better accordance with the Langmuir model than the Freundlich model. The thermodynamics of adsorption demonstrated that the adsorption is exothermic, exhibiting higher removal efficiency at lower temperatures. Furthermore, Gibb's free energy change of adsorption (ΔG) suggested that the adsorption is spontaneous, being more spontaneous for AGO-CTS than GO-CTS hydrogels. Finally, the regeneration ability of the hydrogel adsorbents was studied in five consecutive cycles. The adsorbent maintained its efficiency at a relatively high level for three cycles but a considerable decrease was observed between the third and the fourth cycle, indicating that the hydrogels were recoverable for three cycles.

Molecular dynamics simulations of hyperbranched poly(ethylene imine)-graphene oxide nanocomposites as dye adsorbents for water purification

Atomistically detailed molecular dynamics simulations were employed to study the adsorption capacity of graphene-oxide-based (GO) aqueous systems for the methylene blue (MB) dye in the presence of branched poly(ethylene imine) (BPEI) polymers. The polymeric component was either freely mixed or chemically attached to GO. The main focus was the elucidation of the effects originating from the presence of BPEI molecules in the association of MB with the formed GO complexes. The effect of temperature was also examined. It was found that the presence of the cationic BPEI molecules results in the formation of a distinct microenvironment characterized by a polymer-mediated interconnected morphology which promotes the development of larger-sized MB clusters. These clusters were found to form in the vicinity of the GO flakes, increasing thus the adsorption capacity of the dye molecules in the polymer-containing systems. Particularly in the system with the BPEI-functionalized GO flakes, a persistent percolated structure is formed, which results in a more restricted diffusion of the MB molecules, increasing thus significantly their residence time close to the GO surface. The clustering behavior of MB was found to be temperature-dependent in the BPEI-based models, providing useful information regarding the conditions for optimal adsorption performance of such membranes, in nanofiltration processes.

Synthesis of 3D graphene-based materials and their applications for removing dyes and heavy metals

Contamination of water streams by dyes and heavy metals has become a major problem due to their persistence, accumulation, and toxicity. Therefore, it is essential to eliminate and/or reduce these contaminants before discharge into the natural environment. In recent years, 3D graphene has drawn intense research interests owing to its large surface area, superior charge conductivity, and thermal conductivity properties. Due to their unique surface and structural properties, 3D graphene-based materials (3D GBMs) are regarded as ideal adsorbents for decontamination and show great potential in wastewater or exhaust gas treatment. Here, this minireview summarizes the recent progress on 3D GBMs synthesis and their applications for adsorbing dyes and heavy metals from wastewater based on the structures and properties of 3D GBMs, which provides valuable insights into 3D GBMs' application in the environmental field.

β-Cyclodextrin functionalized 3D reduced graphene oxide composite-based electrochemical sensor for the sensitive detection of dopamine

A three-dimensional reduced graphene oxide nanomaterial with β-cyclodextrin modified glassy carbon electrode (3D-rGO/β-CD/GCE) was constructed and used to detect the electrochemical behavior of dopamine (DA). The nanocomposite materials were characterized by scanning electron microscopy (SEM), infrared spectrometry (FT-IR), Raman spectrogram and thermogravimetric analysis (TGA), which showed that β-CD was well modified on 3D graphene with a porous structure. The electrochemical properties of different modified electrodes were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), proving the highest electron transfer rate of the 3D-rGO/β-CD modified electrode. The experimental conditions such as scan rate, pH, enrichment time and layer thickness were optimized. Under the best experimental conditions, DA was detected by differential pulse voltammetry (DPV) by 3D-rGO/β-CD/GCE with excellent electrocatalytic ability and satisfactory recognition ability, resulting in a wide linear range of 0.5-100 μM and a low detection limit (LOD) of 0.013 μM. The modified electrode based on 3D-rGO/β-CD nanocomposites is promising in the field of electrochemical sensors due to its high sensitivity and other excellent properties.

Cyclodextrin-Cross-Linked Hydrogels for Adsorption and Photodegradation of Cationic Dyes in Aqueous Solution

Possessing three-dimensional porous structures and tunable mechanical strengths, cyclodextrin-containing polymeric hydrogels are one of the most promising water-based adsorbent materials due to their easy availability, simple chemical modification and environmental friendliness. In this work, two kinds of hydrogels were prepared via the copolymerization with acrylic acid and vinyl-derivatized β-cyclodextrins in water. These two gels have showed good adsorption performance towards cationic dyes through the noncovalent interactions with their anionic backbones and porous network. Meanwhile, pseudo-second-order model was selected to clarify the adsorption kinetics process. Moreover, nano-scaled TiO₂ was doped into these resultant cyclodextrins-based hydrogels to achieve efficient degradation of dyes upon light irradiation. The obtained TiO₂ -loaded hydrogels could exhibit improved adsorption performance and make the adsorbed dyes photo-degraded with the decolorization rates above 95%. It can be envisioned that such cyclodextrin-based soft materials may find applications in dye clearance and water treatment.

Graphene-Based Materials Immobilized within Chitosan: Applications as Adsorbents for the Removal of Aquatic Pollutants

Graphene and its derivatives, especially graphene oxide (GO), are attracting considerable interest in the fabrication of new adsorbents that have the potential to remove various pollutants that have escaped into the aquatic environment. Herein, the development of GO/chitosan (GO/CS) composites as adsorbent materials is described and reviewed. This combination is interesting as the addition of graphene to chitosan enhances its mechanical properties, while the chitosan hydrogel serves as an immobilization matrix for graphene. Following a brief description of both graphene and chitosan as independent adsorbent materials, the emerging GO/CS composites are introduced. The additional materials that have been added to the GO/CS composites, including magnetic iron oxides, chelating agents, cyclodextrins, additional adsorbents and polymeric blends, are then described and discussed. The performance of these materials in the removal of heavy metal ions, dyes and other organic molecules are discussed followed by the introduction of strategies employed in the regeneration of the GO/CS adsorbents. It is clear that, while some challenges exist, including cost, regeneration and selectivity in the adsorption process, the GO/CS composites are emerging as promising adsorbent materials.

Efficient adsorption of diclofenac sodium in water by a novel functionalized cellulose aerogel

In this work, a novel cellulose aerogel (CNC-PVAm/rGO) was fabricated using cellulose nanocrystalline (CNC) modified with polyvinylamine (PVAm) and reduced graphene oxide (rGO). The resultant CNC-PVAm/rGO was then applied for the adsorption of diclofenac sodium (DCF), a typical non-steroidal anti-inflammatory drug. Characterization using ultra-high-resolution field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and the Brunauer-Emmett-Teller surface area revealed that the obtained CNC-PVAm/rGO displayed an evident 3D porous structure, which had an ultralight weight, good recovery, abundant surface functional groups (e.g., -NH₂ and -OH), and rGO nanosheets. In addition, the material presented a stable crystal structure and large specific surface area (105.73 m² g^-1). During the adsorption of DCF, the CNC-PVAm/rGO aerogel showed a rather excellent adsorption performance, with a maximum adsorption capacity (q_max) of 605.87 mg g^-1, which was approximately 53 times larger than that of the bare CNC aerogel (11.45 mg g^-1). The adsorption performance of CNC-PVAm/rGO was also better than that of other reported adsorbents. The adsorption of DCF to CNC-PVAm/rGO obeyed the Langmuir isotherm and pseudo-second-order kinetic models, and underwent a spontaneous exothermic process. Moreover, DCF was easily desorbed from CNC-PVAm/rGO with sodium hydroxide solution (0.1 mol L^-1), and the absorbent could be reused four times. The introduction of PVAm and rGO to the CNC-PVAm/rGO aerogel also greatly enhanced electrostatic interactions, π-π interactions, and hydrophobic effects. These enhancements significantly promoted the hydrogen bonding interactions between the DCF molecules and CNC-PVAm/rGO, thus resulting in a large improvement in the adsorption performance of the aerogel.

One-pot fabrication of lignin-based aromatic porous polymers for efficient removal of bisphenol AF from water

To remove the bisphenol AF (BPAF) from aqueous solution, two different types of lignin-based aromatic porous polymers (LAPP-1 and LAPP-2) were fabricated via one-pot crosslinking of lignin with 1,4-dichloroxylene and 4,4'-bis(chloromethyl)-1,1'-biphenyl, respectively. The successful synthesis of LAPPs was confirmed by FTIR and XPS, SEM, TEM and N₂ adsorption-desorption analysis. Then, batch adsorption experiments were conducted to investigate adsorption properties toward BPAF. Based on the results, the adsorption processes were in accordance with the pseudo-second-order kinetic model and the Freundlich isotherm model, and the thermodynamic studies showed that the adsorption was a spontaneous and exothermic process. It is remarkable that LAPPs exhibited good adsorption performance in wide ranges of pH and ionic strength as well as in recycling process. Notably, compared to LAPP-1, LAPP-2 exhibited higher adsorption capacity for BPAF, which can be ascribed to its higher porosity and content of aromatic ring. Moreover, the comprehensive analysis of experimental and theoretical results indicated that the π-π interactions and pore adsorption may jointly drive the uptake process of BPAF. Considering the simple fabrication method employed and excellent BPAF adsorption performance, LAPPs provided new insights into the development of advanced lignin-based adsorbents for removal of BPAF from water.

Recent Developments in Chitosan-Based Adsorbents for the Removal of Pollutants from Aqueous Environments

The quality of water is continuously under threat as increasing concentrations of pollutants escape into the aquatic environment. However, these issues can be alleviated by adsorbing pollutants onto adsorbents. Chitosan and its composites are attracting considerable interest as environmentally acceptable adsorbents and have the potential to remove many of these contaminants. In this review the development of chitosan-based adsorbents is described and discussed. Following a short introduction to the extraction of chitin from seafood wastes, followed by its conversion to chitosan, the properties of chitosan are described. Then, the emerging chitosan/carbon-based materials, including magnetic chitosan and chitosan combined with graphene oxide, carbon nanotubes, biochar, and activated carbon and also chitosan-silica composites are introduced. The applications of these materials in the removal of various heavy metal ions, including Cr(VI), Pb(II), Cd(II), Cu(II), and different cationic and anionic dyes, phenol and other organic molecules, such as antibiotics, are reviewed, compared and discussed. Adsorption isotherms and adsorption kinetics are then highlighted and followed by details on the mechanisms of adsorption and the role of the chitosan and the carbon or silica supports. Based on the reviewed papers, it is clear, that while some challenges remain, chitosan-based materials are emerging as promising adsorbents.

Cyclodextrin Polymers and Cyclodextrin-Containing Polysaccharides for Water Remediation

Chemical pollution of water has raised great concerns among citizens, lawmakers, and nearly all manufacturing industries. As the legislation addressing liquid effluents becomes more stringent, water companies are increasingly scrutinized for their environmental performance. In this context, emergent contaminants represent a major challenge, and the remediation of water bodies and wastewater demands alternative sorbent materials. One of the most promising adsorbing materials for micropolluted water environments involves cyclodextrin (CD) polymers and cyclodextrin-containing polysaccharides. Although cyclodextrins are water-soluble and, thus, unusable as adsorbents in aqueous media, they can be feasibly polymerized by using different crosslinkers such as epichlorohydrin, polycarboxylic acids, and glutaraldehyde. Likewise, with those coupling agents or after substituting hydroxyl groups with more reactive moieties, cyclodextrin units can be covalently attached to a pre-existing polysaccharide. In this direction, the functionalization of chitosan, cellulose, carboxymethyl cellulose, and other carbohydrate polymers with CDs is vastly found in the literature. For the system containing CDs to be used for remediation purposes, there are benefits from a synergy that arises from (i) the ability of CD units to interact selectively with a broad spectrum of molecules, forming inclusion complexes and higher-order supramolecular assemblies, (ii) the functional groups of the crosslinker comonomers, (iii) the three-dimensional structure of the crosslinked network, and/or (iv) the intrinsic characteristics of the polysaccharide backbone. In view of the most recent contributions regarding CD-based copolymers and CD-containing polysaccharides, this review discusses their performance as adsorbents in micropolluted water environments, as well as their interaction patterns, addressing the influence of their structural and physicochemical properties and their functionalization.

In Situ Preparation of Novel Porous Nanocomposite Hydrogel as Effective Adsorbent for the Removal of Cationic Dyes from Polluted Water

The use of some hydrogels as adsorbents for pollutants removal from wastewater is limited due to their high swelling properties and the difficulty in recovering them after the adsorption process. To overcome these problems, a new hydrogel nanocomposite based on chitosan-grafted-polyacrylic acid/oxidized electrospun carbon nanofibers (CT-g-PAA/O-ECNFs) was prepared by an in situ grafting polymerization process. The prepared hydrogel nanocomposite was used as a novel effective and highly reusable adsorbent for the removal of methylene blue (MB) from polluted water with low cost. The morphology and the structure of CT-g-PAA/O-ECNFs were investigated by numerous techniques. The effect of incorporating O-ECNFs on the swelling capability of the prepared hydrogel was explored in distillated water and MB solution at normal pH. The effect of parameters including ratio of O-ECNFs, contact time, pH, initial concentration, and temperature on adsorption process were explored. The adsorption isotherm and kinetic were studied by numerous non-linear models. The obtained results confirmed that the incorporation of O-ECNFs into the hydrogel network decreased the swelling capacity and improved its ability towards MB dye removal. The adsorption process depended on the pH value of the dye solution. Additionally, the adsorption and kinetic results were fitted using the Freundlich isotherm model and pseudo second order model (PSO), respectively. Moreover, the new adsorbents can be recycled for at least five cycles keeping its adsorption capacity and can be easily recovered without loss in its initial weight.

Graphene and graphene-based nanocomposites used for antibiotics removal in water treatment: A review

Due to their extensive application in human and veterinary medicine, antibiotics have been found worldwide and studied as new pollutants in the aquatic environment. In order to remove such pollutants, adsorption and photocatalysis have attracted tremendous attention because of their great potential in antibiotics removal from aqueous solutions. Graphene, as a novel two-dimensional nanomaterial, possesses unique structure and physicochemical properties, which can be used to efficiently adsorb and photodegrade antibiotics. This review provides an overview of the adsorptive and catalytic properties of graphene, and recent advances in adsorption and photodegradation of antibiotics by graphene and its derivatives. The factors that affect the adsorption and photodegradation of antibiotics are reviewed and discussed. Furthermore, the underlying mechanisms of adsorption and photodegradation are summarized and analyzed. Meanwhile, statistical analysis is conducted based on the number of papers and the maximum adsorption and photodegradation ability on various antibiotics removal. Finally, some unsolved problems together with major challenges that exist in the fabrication and application of graphene-based nanocomposites and the development for antibiotics removal is also proposed. This work provides theoretical guidance for subsequent research in the field of adsorption and photocatalytic removal of antibiotics from aqueous solution, especially on influence factors and mechanisms aspects.