Synthesis of Cu2O nanocrystals/TiO2 photonic crystal composite for efficient p-nitrophenol removal

Synergistic Effect of Amorphous Ti(IV)-Hole and Ni(II)-Electron Cocatalysts for Enhanced Photocatalytic Performance of Bi2WO6

Bi2WO6 has become a common photocatalyst due to its advantages of simple synthesis and high activity. However, the defects of pure Bi2WO6 such as low light reception hinder its application in photocatalysis. In this study, based on the modification of Bi2WO6 with Ti(IV) as a cavity co-catalyst, new Ni- and Ti-doped nanosheets of Bi2WO6 (Ni/Ti-Bi2WO6) were prepared by a one-step wet thermal impregnation method and used for the photocatalytic degradation of tetracycline. The experimental results showed that the photocatalytic activity of Ni/Ti-Bi2WO6 modified by the two-component catalyst was significantly better than those of pure Bi2WO6 and Ti-Bi2WO6 modified with Ti(IV) only. The photocatalytic effect of Ni/Ti-Bi2WO6 with different Ni/Ti molar ratios was investigated by the degradation of TC. The results showed that 0.4Ni/Ti-Bi2WO6 possessed the best photocatalytic performance, with a degradation rate of 92.9% at 140 min TC. The results of cycling experiments showed that the catalyst exhibited high stability after five cycles. The scavenger experiment demonstrated that the h+ and O2− were the main reactive species. The enhanced photocatalytic activity of Bi2WO6 could be attributed to the synergistic effect between the Ti(IV) as a hole cocatalyst and Ni(II) as an electron cocatalyst, which effectively promoted the separation of photogenerated carriers.

Recent developments in photocatalysis of industrial effluents ։ A review and example of phenolic compounds degradation

Industrial expansion and increased water consumption have created water scarcity concerns. Meanwhile, conventional wastewater purification methods have failed to degrade recalcitrant pollutants efficiently. The present review paper discusses the recent advances and challenges in photocatalytic processes applied for industrial effluents treatment, with respect to phenolic compounds degradation. Key operational parameters including the catalyst loading, light intensity, initial pollutants concentration, pH, and type and concentrations of oxidants are evaluated and discussed. Compared to the other examined controlling parameters, pH has the highest effect on the photo-oxidation of contaminants by means of the photocatalyst ionization degree and surface charge. Furthermore, major phenolic compounds derived from industrial sources are comprehensively presented and the applicability of photocatalytic processes and the barriers in practical applications, including high energy demand, technical challenges, photocatalyst stability, and recyclability have been explored. The importance of energy consumption and operational costs for realistic large-scale processes are also discussed. Finally, research gaps in this area and the suggested direction for improving degradation efficiencies in industrial applications are presented. In the light of these premises, selective degradation processes in real water matrices such as untreated sewage are proposed.

Cu2+doped TiO2-SiO2with photonic crystal structure for synergistic enhancement of photocatalytic degradation under visible light irradiation

The development of visible light photocatalysts with the ability to efficiently degrade pollutants is an important measure to solve environmental problems. In this paper, Cu²⁺doped TiO₂-SiO₂(CTS) with photonic crystal structure composite was successfully synthesized via sol-gel strategy and template method. The prepared materials have abundant pore structure and uniform pore diameter, and the pores were arranged in a periodically hexagonal structure. It showed enhancing synergistic effect of adsorption-photodegradation ability for removing Rhodamine B (RhB). The brilliant adsorption capability of the catalyst is not only due to the addition of silica which can increase surface area that results the increase in adsorption ability, but also related to the rich and ordered porous structure provided by the photonic crystal. The catalyst has a narrow band gap ∼2.92 eV which exhibits the excellent photocatalytic activity for RhB degradation (>95% at 30 min) under visible light irradiation, and possesses higher photocatalytic reaction apparent rate constants (k) which is 7 folds higher than that of pure TiO₂. The excellent photocatalytic performance is attributed to the Cu²⁺doping that narrows the band gap, increases light absorption, and promotes charge separation. Besides, the constructed photonic crystal structure not only further enhances charge transport but also provides more surface activity sites for photocatalytic reactions. More importantly, the ordered pore structure-photonic crystal can prolong the interaction time between light and catalyst through the slow photon effect and the porous scattering effect. Eventually, the photocatalytic degradation efficiency of the catalyst was significantly improved by the synergistic effect of the above mechanisms.

Efficient N, Fe Co-Doped TiO2 Active under Cost-Effective Visible LED Light: From Powders to Films

An eco-friendly photocatalytic coating, active under a cost-effective near-visible LED system, was synthesized without any calcination step for the removal of organic pollutants. Three types of doping (Fe, N and Fe + N), with different dopant/Ti molar ratios, were investigated and compared with undoped TiO2 and the commercial P25 photocatalyst. Nano-crystalline anatase-brookite particles were successfully produced with the aqueous sol-gel process, also at a larger scale. All samples displayed a higher visible absorption and specific surface area than P25. Photoactivity of the catalyst powders was evaluated through the degradation of p-nitrophenol in water under visible light (>400 nm). As intended, all samples were more performant than P25. The N-doping, the Fe-doping and their combination promoted the activity under visible light. Films, coated on three different substrates, were then compared. Finally, the photoactivity of a film, produced from the optimal N-Fe co-doped colloid, was evaluated on the degradation of (i) p-nitrophenol under UV-A light (365 nm) and (ii) rhodamine B under LED visible light (395 nm), and compared to undoped TiO2 film. The higher enhancement is obtained under the longer wavelength (395 nm). The possibility of producing photocatalytic films without any calcination step and active under low-energy LED light constitutes a step forward for an industrial development.

Construction of rGO wrapping Cu2O/ZnO heterostructure photocatalyst for PNP and PAM degradation

Copper and zinc composite oxides (Cu₂O/ZnO) were synthesized by an impregnation-reduction-air oxidation method. A series of Cu₂O/ZnO/rGO ternary composites were prepared by coupling with graphene oxide (GO) with different mass fractions in a solvothermal reaction system. The microscopic morphology, crystal structure, and optical characteristics of the photocatalysts were characterized. The degradation of p-Nitrophenol (PNP) and polyacrylamide (PAM) by photocatalytic materials under simulated solar irradiation were studied, and the degradation kinetics were also investigated. The results showed that cubic Cu₂O was modified by ZnO nanorods and distributed on rGO nanosheets. The ternary Cu₂O/ZnO/rGO nanocomposites have stronger simulated solar absorption ability and higher photodegradation efficiency than pure ZnO and binary Cu₂O/ZnO nanocomposites. When the amount of Cu₂O/ZnO/rGO-10 was 0.3 g L^-1, the degradation rate of 10 mg L^-1 PNP reached 98% at 90 min and 99.6% of 100 mg L^-1 PAM at 30 min. The photocatalytic degradation processes of PNP and PAM all followed the pseudo-first-order kinetic model. Free radical trapping experiments showed that superoxide radicals were the main active substances to improve photocatalytic efficiency. In addition, after four recycles, the catalytic efficiency of Cu₂O/ZnO/rGO-10 was still over 90%. It showed that Cu₂O/ZnO/rGO-10 was a promising catalyst for wastewater treatment because of its good photostability and reusability.

AuNPs-Based Thermoresponsive Nanoreactor as an Efficient Catalyst for the Reduction of 4-Nitrophenol

A new AuNPs-based thermosensitive nanoreactor (SiO₂@PMBA@Au@PNIPAM) was designed and prepared by stabilizing AuNPs in the layer of poly(N,N'-methylenebisacrylamide) (PMBA) and subsequent wrapping with the temperature-sensitive poly(N-isopropylacrylamide) (PNIPAM) layer. The new nanoreactor exhibited high dispersibility and stability in aqueous solution and effectively prevented the aggregation of AuNPs caused by the phase transformation of PNIPAM. The XPS and ATR-FTIR results indicated that AuNPs could be well stabilized by PMBA due to the electron transfer between the N atoms of amide groups in the PMBA and Au atoms of AuNPs. The catalytic activity and thermoresponsive property of the new nanoreactor were invested by the reduction of the environmental pollutant, 4-nitrophenol (4-NP), with NaBH₄ as a reductant. It exhibited a higher catalytic activity at 20 °C and 30 °C (below LCST of PNIPAM), but an inhibited catalytic activity at 40 °C (above LCST of PNIPAM). The PNIPAM layer played a switching role in controlling the catalytic rate by altering the reaction temperature. In addition, this nanoreactor showed an easily recyclable property due to the existence of a silica core and also preserved a rather high catalytic efficiency after 16 times of recycling.