Morphology-controlled hydrothermal synthesis and photocatalytic Cr(VI) reduction properties of α-Fe2O3

Aerobic Fe transformation induced decrease in the adsorption and enhancement in the reduction of Cr(VI) by humic acid-ferric iron coprecipitates

Humic substance (HS)-ferric iron (Fe(III)) coprecipitates are widespread organo-mineral associations in soils and aquifers and have the capacity to immobilize and detoxify Cr(VI). These coprecipitates undergo transformation owing to their thermodynamic instability; however, the effects of this transformation on their environmental behaviors remain unclear, particularly in aerobic environments. In this study, the aerobic transformation of humic acid (HA)-Fe(III) coprecipitates, a representative of HS-Fe(III) coprecipitates, was simulated. The environmental effect was then evaluated after conducting an adsorption-reduction batch experiment toward Cr(VI). The aerobic transformation characteristics, as well as the adsorption/reduction capacity of HA-Fe(III) coprecipitates, were found to depend strongly on their structures. In ferrihydrite (Fh)-like coprecipitates, amorphous Fh is readily transformed into crystalline hematite and goethite at aerobic environments, leading to a much lower specific surface area and adsorption capacity. However, this increasing degree of crystallization enhanced the inductive reduction ability towards Cr(VI) owing to the more significant shift of electron pairs in the FeOC bond toward the HA direction. In HS-like coprecipitates, Fe(III) always serves as a cation bridge connecting HA molecules, but can be reduced to Fe(II) by the associated HA after aerobic transformation. The produced Fe(II), therefore, drove the reduction of the adsorbed Cr(VI). These findings emphasize the pivotal role of aerobic transformation in enhancing the reduction capacity for Cr(VI), which opens a new avenue for the development of in-situ remediation agents for Cr(VI)-contaminated sites.

The corncobs-loaded iron nanoparticles enhanced mechanism of denitrification performance in microalgal-bacterial aggregates system when treating low COD/TN wastewater

To improve denitrification efficiency of microalgal-bacterial aggregates (MABAs) when treating low carbon to nitrogen (C/N) ratio wastewater, CK (the biological control), C1 (untreated corncobs), C2 (alkali-treated corncobs), CFe1 (C1 loaded iron nanoparticles) and CFe2 (C2 loaded iron nanoparticles) five groups of experiments were installed under artificial light (1600 lm). After 36 h of experiment, NO3--N was almost completely converted in CFe1 following by CFe2 when the initial concentration was 60.1 mg/L, whose NO3--N conversion rates were 6.2 and 3.4 times faster than the CK group, respectively. The result showed that the corncobs-loaded iron nanoparticles (CFe1, CFe2) had the potential to promote denitrification process and the CFe1 was more effective. Meanwhile, the CFe1 and CFe2 resulted in a decreased content in extracellular polymeric substances (EPS) secretion because iron nanoparticles (Fes) promoted electron transport and alleviated the nitrate stress. Moreover, the electrochemical analysis of EPS showed that the corncobs and corncobs-loaded iron nanoparticles improved the electron transport rate and redox active substances production. The increase in electron transport activity (ETSA), adenosine triphosphate (ATP) and nicotinamide adenine dinucleotide (NADH) also indicated that the CFe1 and CFe2 promoted microbial metabolic activity and the electron transport rate in MABAs. In addition, the CFe1 group enhanced the enrichment of Proteobacteria, Patescibacteria, Chlorophyta and Ignavibacteriae, which was contributed to the nitrogen removal performance of MABAs. In summary, the enhancement mechanism of corncobs-loaded iron nanoparticles on denitrification process of MABAs was depicted through EPS secretion, electrochemical characteristics, microbial metabolic activity and microbial community. The article provides a viable program for enhancing the denitrification performance of MABAs when treating low C/N wastewater.

Synthesis and Photocatalytic Application of Magnetic CoFe2O4/Conjugated Poly(vinyl chloride) Derivative Nanocomposite

CoFe2O4 has potential for application as a magnetically recoverable visible-light photocatalyst, but its photocatalytic activity is encumbered by the high recombination probability of its photogenerated holes (h+) and electrons (e-). This work was undertaken to boost the photocatalysis of CoFe2O4 through coupling with conjugated poly(vinyl chloride) derivative (CPVC). An easily implementable solvothermal-liquid solid mixing-evaporation of the solvent-pyrolysis method was exploited to synthesize CoFe2O4/CPVC nanocomposites. The photocatalytic capabilities of the products were assessed through photocatalyzing the reduction of Cr(VI) under visible-light (λ > 420 nm). The results demonstrate that the optimal CoFe2O4/CPVC nanocomposite (CoFe2O4/CPVC-2) has markedly heightened photocatalytic activity (3.6 times that of CoFe2O4) and competent reusability and is magnetically recoverable. Furthermore, CoFe2O4/CPVC-2 also shows superior performance toward photocatalytic treatment of the diluted Cr(VI)-containing passivation solution of copper alloys. It is deduced based on the photoelectricity measurement results that the increased photocatalysis of CoFe2O4/CPVC-2 is chiefly attributed to its p-n heterojunction structure, which greatly elevates the h+-e- separation and transfer efficiency. When waste PVC plastic films (replacing the new pure PVC powder) were utilized for the synthesis, the obtained CoFe2O4/CPVC nanocomposite exhibited even better photocatalytic activity (4 times that of CoFe2O4). This work not only has made a new magnetically recoverable, efficient visible-light photocatalyst for decontamination of Cr(VI) in water but also is inspirational for recycling PVC plastic waste to produce high-valued visible-light photocatalysts.

Facile synthesis of highly basic, nanocrystalline Fe2O3-NiO composites as promising and durable catalysts for selective dehydrogenation of 2-butanol

Nanocrystalline Fe2O3-NiO composite catalysts were prepared using a sonication-assisted green preparation method. The prepared catalysts were characterized using different techniques, including thermal analyses (TGA/DTA), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, surface area measurements (SBET), and scanning electron microscopy (SEM). The surface basicity of the prepared catalysts was measured using the temperature-programmed desorption of CO2 (CO2-TPD) as a highly acidic probe molecule. The catalytic activity of all the prepared catalysts was tested at a temperature range of 250-325 °C towards the dehydrogenation of 2-butanol to methyl-ethyl ketone (MEK), which is considered a promising fossil fuel alternative and has several industrial applications. The composite catalysts showed better catalytic activity compared to the pure oxides (i.e., Fe2O3 and NiO) due to the strong synergetic effect between the two oxides. Fe2O3 prevented the coke formation over the surface of NiO by the oxygen-scavenging effect of Fe, which promotes the oxidation of the carbonaceous species and increases the catalyst's resistance to deactivation. The effect of weight hourly space velocity (WHSV) on the catalytic activity was tested over a selected catalyst. In addition, the stability and durability of the catalyst were tested across four successive reaction cycles, demonstrating remarkable performance throughout all the reaction cycles.

Hexavalent Chromium Reduction Mediated by Interfacial Electron Transfer over the Co@NC Nanosheet-Assembled Microflowers

The reductive transformation of Cr(VI) into Cr(III) mediated by formic acid with efficient, stable, and cost-effective catalysts is a promising strategy for remediating Cr(VI) contamination. Herein, we report the facile construction of uniform Co@NC nanosheet-assembled microflowers for the reduction of Cr(VI). Both experimental results and density functional theory (DFT) calculations reveal the vital role of the intensive interfacial electronic interaction between Co nanoparticles and the N-doped carbon layer in facilitating the anchoring and dispersion of Co nanoparticles within the carbon framework. The interfacial electron transfer from Co to NC contributes to the interaction with Cr2O72- ions, promoting the subsequent H-transfer reaction. A Langmuir-Hinshelwood kinetic model has been established for the Cr(VI) reduction catalyzed by the CNCF2 (pyrolyzed at 700 °C), which shows a superior reaction performance. This study provides a facile strategy to delicately design well-assembled heterostructures with rich interfaces and strong interfacial interactions for a series of applications in environmental/thermal catalysis.

Effective elimination of hexavalent chromium and lead from solution by the modified biochar with MgMn2O4 nanoparticles: adsorption performance and mechanism

Heavy metal pollution is one of the environmental problems that need to be solved urgently. The adsorption method is thought as the most effective and economical treatment technology. Nature biochar usually showed unsatisfactory adsorption capacity due to its relatively small adsorption capacity and slow adsorption rate. The metal of Mn has been widely applied in the modification of biochar, which could effectively improve the adsorption capacity of biochar. However, leaching of Mn2+ on the adsorbent materials would appear during the adsorption process. And it would increase the risk of secondary pollution. The multifunctional binary modified biochar could improve the adsorption capacity of environmental pollutant removal. In addition, it could also act as a metal support carrier, reducing the risk of secondary pollution. A novel effective biochar loaded by Mg-Mn binary oxide nanoparticles (MgMn2O4@Biochar) was prepared and applied for the Cr(VI) and Pb(II) removal in aqueous solution. The characteristic of MgMn2O4@Biochar was analyzed by SEM, TEM, FTIR, and XRD. The irregular and somewhat flaky shaped particles of different shape and sizes clustered on the surface of MgMn2O4@Biochar appeared. Abundant functional groups of O-H, -C-OH, C-O, and C-OOH could be observed on the surface of MgMn2O4@Biochar. The elements of Mg and Mn elements besides of C, O, and Si elements were presented on the surface of MgMn2O4@Biochar. The wt% of C, O, Mg, Mn, and Si were 42.82%, 48.99%, 2.83%, 4.44%, and 0.93%, respectively. The operational parameters had an important influence on adsorption capacity of Cr(VI) and Pb(II) removal. The results showed that the adsorption capacity of MgMn2O4@Biochar for Cr(VI) and Pb(II) would reach 33.5 mg/g and 536 mg/g, respectively, within 360 min. Additionally, the adsorption processes of Cr(VI) and Pb(II) in solution could be described with pseudo-second-order. For Cr(VI), the Langmuir model was suitable to the adsorption process. However, the adsorption process of Pb(II) in solution could be described with Freundlich model. Furthermore, it could be concluded that the possible mechanism of Cr(VI) and Pb(II) removal by MgMn2O4@Biochar was physical adsorption, surface complexation reaction, and electrostatic adsorption.

Photoluminescence Investigations and Band Gap Engineering in Environment Friendly ZnO Nanorods: Enhanced Water Treatment Application and Defect Model

The inadvertent discharge of industrial effluents, mainly textile, contributes to the complex contamination load in water bodies. Textile dyes are the critical effluents and recalcitrant to traditional remediation procedures. Therefore, energy viable and environment friendly solutions are needed. In this study, we have synthesized zinc oxide nanorods (NRs) at various temperatures using modified thermal decomposition and evaluated its photocatalytic activities. Field effect scanning electron microscopy has confirmed rod-like morphology till TS = 500 °C and spherical morphology from TS = 600 °C onward. Photoluminescence spectra have shown a prominent defect peak in the synthesized ZnO, except for the NRs synthesized at 300 °C. Synthesized ZnO NRs and NPs have been employed to degrade crystal violet (CV) and congo red (CR) dyes. ZnO NRs have shown impressive photocatalytic performance with faster treatment time as compared to the earlier reports. Synthesis parameters are well correlated with the observed high efficiency and the band gap tailoring. Based on our findings, for the first time, we have proposed (i) defect model correlating synthesis parameters with defect states, (ii) systematic correlation of defect states with photocatalytic efficiency, and (iii) ZnO nanorods synthesized at 300 °C via an improved synthesis method as a promising photocatalytic solution to degrade the CV and CR dyes in contaminated water.

One-step calcination synthesis of 2D/2D g-C3N4/WS2 van der Waals heterojunction for visible light-induced photocatalytic degradation of pharmaceutical pollutants

It is well-documented that accumulation of pharmaceutically active compounds (PhACs), such as antibiotics, in aquatic ecosystems is a prominent environmental hazard. Herein, a series of 2D materials-based heterojunctions, conceptualized based on the integration of graphitic carbon nitride (g-C₃N₄) with tungsten disulfide (WS₂), was fabricated through a facile one-step calcination process, and systematically evaluated for eliminating tetracycline (TC) and sulfamethoxazole (SMX) from aqueous matrices. The microstructure, optical properties, and surface chemistry of the as-prepared composites were examined with a range of microscopy and spectroscopy techniques. In comparison with pristine g-C₃N₄ or bare WS₂, the g-C₃N₄/WS₂ material, with optimal WS₂ loading, showed significantly improved photocatalytic activity, towards degradation of TC (84%) and SMX (96%), under visible light. Free radical scavenging experiments revealed that superoxide anions and hydroxyl radicals were predominantly responsible for the rapid breakdown of the PhACs. In addition, the dissociation intermediates and residues were identified and the plausible photocatalytic degradation pathways of TC and SMX over the as-constructed 2D/2D heterojunction were discussed. Further, the photocatalysis end products were non-toxic, as inferred via the resazurin cell viability assay, employing Escherichia coli as a model organism. Most importantly, the 2D/2D g-C₃N₄/WS₂ architecture was structurally resilient and exhibited a fairly stable cycling performance for persistent usage in wastewater treatment. The outcomes of this study testify that 2D/2D heterojunction of g-C₃N₄ fragments and WS₂ nanosheets holds great promise for destroying antibiotics or their metabolites, usually present in wastewaters.

Efficient photocatalytic degradation of Rhodamine B dye using solar light-driven La-Mn co-doped Fe2O3 nanoparticles

This work aims to develop a highly efficient solar light-induced photocatalyst based on La-Mn co-doped Fe₂O₃ nanoparticles. Pure Fe₂O₃ and La-Mn co-doped Fe₂O₃ nanoparticles were fabricated by a simple co-precipitation method. The photocatalysts were analyzed for their morphological, structural, and magnetic characteristics. Scanning electron microscopy analysis demonstrated the formation of semi-spherical nanoparticles along with small aggregations. The size of nanoparticles was measured using a transmission electron microscope and found in the range of 42-49 nm. The crystalline nature and geometry of synthesized nanoparticles were investigated using X-ray diffraction analysis. Due to the incorporation of La-Mn, the saturation magnetization and remanent magnetization of the nanoparticles decreased from 6.17 to 2.89 emu/g and 1.15 to 0.52 emu/g, respectively, while the coercivity was reduced from 756.72 to 756.67 Oe. The surface area of nanoparticles was increased from 77.93 to 87.45 m²/g as a result of La-Mn co-doping. The photocatalytic performance of the Fe₂O₃, La_0.1Mn_0.3Fe_1.6O₃, and La_0.2Mn_0.2Fe_1.6O₃ catalysts was assessed by their capability to degrade Rhodamine B (RhB) under solar light illumination. La_0.2Mn_0.2Fe_1.6O₃ displayed exceptional degradation performance, degrading RhB to 91.78% in 240 min, in comparison to La_0.1Mn_0.3Fe_1.6O₃ (71.09%) and pristine Fe₂O₃ (58.21%) under specified reaction conditions ((RhB) = 50 ppm; (catalyst) = 40 mg/L; pH = 7; T = 25 °C)). RhB degradation was affected by changing pH, catalytic dosage, dye concentration, and temperature. The degradation of RhB was found to be pseudo-1st order kinetics. The exceptional photocatalytic performance of La_0.2Mn_0.2Fe_1.6O₃ catalysts showed that the synthesized nanoparticles could be effectively utilized to remove organic pollutants from industrial wastewater.

Green synthesis of two-electron centre based ZnO/NiCo2S4 QDs-OVs using Punica granatum fruit peel extract for an exceptional visible light photocatalytic degradation of doxycycline and ciprofloxacin

Biosynthesis of nanomaterials using plant extract makes them attractive in the field of photocatalysis as they are environmental friendly. The current study focused on the biosynthesis of ZnO/NiCo₂S₄ QDs (NCs) using Punica granatum fruit peel extract as the reducing agent. The nanomaterials were characterized with XRD, FTIR, Raman, SEM, TEM, UV-vis DRS, BET, PL, EIS, and ESR analysis and were used for photocatalytic degradation of doxycycline (DOX) and ciprofloxacin (CIP). The bandgap of ZnO is 3.2 eV, and the decoration of NiCo₂S₄ QDs aids in narrowing the bandgap (2.8 eV), making the NCs visible light active. The fabricated NCs achieved 99 and 89% degradation of DOX and CIP respectively. The photocatalytic efficiency of ZnO/NiCo₂S₄ QDs was much higher compared to individual ZnO and NiCo₂S₄ QDs. The half-life period of DOX and CIP were evaluated to be 58 and 152 min respectively. The percentage of TOC removal in the photodegraded product of DOX and CIP was estimated to be 99 and 89% respectively, indicating the mineralization of the compounds. The enhanced photocatalytic efficiency of the NCs was attributed to the narrowed visible light active bandgap, synergistic charge transfer across the interface, and lower charge recombination. The intermediates formed during the photocatalytic degradation of DOX and CIP were analyzed using GC-MS/MS analysis, and the photodegradation pathway was elucidated. Also, the toxicity of the intermediates was computationally analyzed using ECOSAR software. The fabricated ZnO/NiCo₂S₄ QDs have excellent stability and reusability, confirmed by XRD and XPS analysis. The reusable efficiency of the NCs for the photocatalytic degradation of DOX and CIP were 98.93, and 99.4% respectively. Thus, the biologically fabricated NCs are shown to be an excellent photocatalyst and have wide applications in environmental remediation.

Synergistic Cr(VI) Reduction and Chloramphenicol Degradation by the Visible-Light-Induced Photocatalysis of CuInS2: Performance and Reaction Mechanism

Despite significant scientific efforts in the field of water treatment, pollution of drinking water by toxic metal ions and synthetic organic compounds is becoming an increasing problem. The photocatalytic capabilities of CuInS₂ nanoparticles were examined in this study for both the degradation of chloramphenicol (CAP) and the reduction of Cr(VI). CuInS₂ nanoparticles were produced using a straightforward solvothermal approach and subsequently characterized by many analysis techniques. Simultaneous photocatalytic Cr(VI) reduction and CAP oxidation by the CuInS₂ nanoparticles under visible-light demonstrated that lower pH and sufficient dissolved oxygen favored both Cr(VI) reduction and CAP oxidation. On the basis of active species quenching experiments, the possible photocatalytic mechanisms for Cr(VI) conversion with synchronous CAP degradation were proposed. Additionally, the CuInS₂ retains a high rate of mixed pollutant removal after five runs. This work shows that organic contaminants and heavy metal ions can be treated concurrently by the visible-light-induced photocatalysis of CuInS₂.

Ag doped Sn3O4 nanostructure and immobilized on hyperbranched polypyrrole for visible light sensitized photocatalytic, antibacterial agent and microbial detection process

Ag doped Sn₃O₄ Nanostructure and immobilized on hyperbranched polypyrrole is investigated in this project. The product was synthesized by the hydrothermal synthesis method. The surface and structural characteristics of the product was studied by different instrumental analysis. The fabricated nanocomposites was utilized as a nano photocatalyst in the removal of methylene blue dye. The crystallography results depicts the triclinic phase of Sn₃O₄ with the crystallite size 36.3 nm. The band gap of the Ag-Sn₃O₄/hyperbranched polypyrrole was found 1.50 eV from kubelka-munk measurements. The specific surface area was increased in the presence of the hyperbranched polypyrrole as compared to Ag-Sn₃O₄ samples. The photo-catalytic activity of composites was found 100.0% degradation of CR in 30 min under visible light irradiation. The catalytic kinetic was followed from the first kinetic model. Moreover, the Ag/Sn₃O₄/hyperbranched polypyrrole was applied as a bactericidal agent against Streptococcus pneumoniae, and Pseudomonas aeruginosa bacteria. Determination of Streptococcus pyogenes as a pathogenic bacteria was investigated by using aptamer/Ag/Sn₃O₄/hyperbranched polypyrrole in peroxidase activity. The detection limit of S. pyogenes was 71.0 CFU/mL by using the nano-aptamer.