Investigation of silicon carbon nitride nanocomposite films as a wear resistant layer in vitro and in vivo for joint replacement applications

Multifunctional hydrogels based on photothermal therapy: A prospective platform for the postoperative management of melanoma

Preventing the recurrence of melanoma after surgery and accelerating wound healing are among the most challenging aspects of melanoma management. Photothermal therapy has been widely used to treat tumors and bacterial infections and promote wound healing. Owing to its efficacy and specificity, it may be used for postoperative management of tumors. However, its use is limited by the uncontrollable distribution of photosensitizers and the likelihood of damage to the surrounding normal tissue. Hydrogels provide a moist environment with strong biocompatibility and adhesion for wound healing owing to their highly hydrophilic three-dimensional network structure. In addition, these materials serve as excellent drug carriers for tumor treatment and wound healing. It is possible to combine the advantages of both of these agents through different loading modalities to provide a powerful platform for the prevention of tumor recurrence and wound healing. This review summarizes the design strategies, research progress and mechanism of action of hydrogels used in photothermal therapy and discusses their role in preventing tumor recurrence and accelerating wound healing. These findings provide valuable insights into the postoperative management of melanoma and may guide the development of promising multifunctional hydrogels for photothermal therapy.

Characteristics of Si (C,N) Silicon Carbonitride Layers on the Surface of Ni-Cr Alloys Used in Dental Prosthetics

Chromium- and cobalt-based alloys, as well as chrome-nickel steels, are most used in dental prosthetics. Unfortunately, these alloys, especially nickel-based alloys, can cause allergic reactions. A disadvantage of these alloys is also insufficient corrosion resistance. To improve the properties of these alloys, amorphous Si (C,N) coatings were deposited on the surfaces of metal specimens. This paper characterizes coatings of silicon carbide nitrides, deposited by the magnetron sputtering method on the surface of nickel-chromium alloys used in dental prosthetics. Depending on the deposition parameters, coatings with varying carbon to nitrogen ratios were obtained. The study analyzed their structure and chemical and phase composition. In addition, a study of surface wettability and surface roughness was performed. Based on the results obtained, it was found that amorphous coatings of Si (C,N) type with thicknesses of 2 to 4.5 µm were obtained. All obtained coatings increase the value of surface free energy. The study showed that Si (C,N)-type films can be used in dental prosthetics as protective coatings.

Properties of SiCN Films Relevant to Dental Implant Applications

The application of surface coatings is a popular technique to improve the performance of materials used for medical and dental implants. Ternary silicon carbon nitride (SiCN), obtained by introducing nitrogen into SiC, has attracted significant interest due to its potential advantages. This study investigated the properties of SiCN films deposited via PECVD for dental implant coatings. Chemical composition, optical, and tribological properties were analyzed by adjusting the gas flow rates of NH3, CH4, and SiH4. The results indicated that an increase in the NH3 flow rate led to higher deposition rates, scaling from 5.7 nm/min at an NH3 flow rate of 2 sccm to 7 nm/min at an NH3 flow rate of 8 sccm. Concurrently, the formation of N-Si bonds was observed. The films with a higher nitrogen content exhibited lower refractive indices, diminishing from 2.5 to 2.3 as the NH3 flow rate increased from 2 sccm to 8 sccm. The contact angle of SiCN films had minimal differences, while the corrosion rate was dependent on the pH of the environment. These findings contribute to a better understanding of the properties and potential applications of SiCN films for use in dental implants.

Sprayable β-FeSi2 composite hydrogel for portable skin tumor treatment and wound healing

The development of a rapid-forming in-situ sprayable hydrogel with the functions of tumor treatment and wound healing is essential for eliminating residual tumor tissue and promoting wound healing caused by surgical resection. On account of its semiconductor properties, β-FeSi₂ (FS) was widely explored as a thermoelectric material. In this work, FS was first applied as a bioactive material for the application of tissue engineering. Excitedly, we found that FS could be used as a novel antitumor agent. It exhibited excellent photothermal performance, and the released Fe ions could generate •OH under the acidic conditions and excessive H₂O₂ in the tumor microenvironment. Moreover, the sprayable β-FeSi₂-incorporated sodium alginate (FS/SA) hydrogel was prepared as an instant gelation after spraying in situ, contributing to timely tumor-induced skin wound healing and efficiently suppressing tumors through photothermal and chemodynamic therapy (PTT and CDT). Furthermore, the released bioactive Fe and Si ions could promote the migration and differentiation of endothelial cells and the pro-angiogenesis of skin wounds. Accordingly, such sprayable hydrogel played an effective role in emergency wound treatment with the advantage of convenience and portability. Overall, with incorporation of FS into the sprayable FS/SA hydrogel, the composite hydrogel possessed dual functions of tumor therapy and skin wound healing.

In vivo biocompatibility of diamond-like carbon films containing TiO2 nanoparticles for biomedical applications

Hybrid diamond-like carbon (DLC) with incorporated titanium dioxide (TiO₂) nanoparticle coatings have low friction coefficient, high wear resistance, high hardness, biocompatibility, and high chemical stability. They could be employed to modify biomedical alloys surfaces for numerous applications in biomedical engineering. Here we investigate for the first time the in vivo inflammatory process of DLC coatings with incorporated TiO₂ nanoparticles. TiO₂-DLC films were grown on AISI 316 stainless-steel substrates using plasma-enhanced chemical vapor deposition. The coated substrates were implanted in CF1 mice peritoneum. The in vivo cytotoxicity and biocompatibility of the samples were analyzed from macrophage lavage. Analysis in the first weeks after implantation could be helpful to evaluate the acute cytotoxicity generated after a possible inflammatory process. The in vivo results showed no inflammatory process. A significant increase in nitric oxide production on the uncoated substrates was confirmed through cytometry, and the coated substrates demonstrated biocompatibility. The presence of TiO₂ nanoparticles enhanced the wound healing activity, due to their astringent and antimicrobial properties. DLC and TiO₂-DLC coatings were considered biocompatible, and the presence of TiO₂ nanoparticles reduced the inflammatory reactions, increasing DLC biocompatibility.

Si-Fe-C-N Coatings for Biomedical Applications: A Combinatorial Approach

Ceramic coatings may prolong the lifetime of joint implants. Certain ions and wear debris may however lead to negative biological effects. SiN-based materials may substantially reduce these effects, but still need optimization for the application. In this study, a combinatorial deposition method enabled an efficient evaluation of a range of Si-Fe-C-N coating compositions on the same sample. The results revealed compositional gradients of Si (26.0-33.9 at.%), Fe (9.6-20.9 at.%), C (8.2-13.9 at.%) and N (39.7-47.2 at.%), and low oxygen contaminations (0.3-0.6 at.%). The mechanical properties varied with a hardness (H) ranging between 13.7-17.3 GPa and an indentation modulus (M) between 190-212 GPa. Both H and M correlated with the Si (H and M increased as Si increased) and Fe (H and M decreased as Fe increased) content. A slightly columnar morphology was observed in cross-sections, as well as a surface roughness in the nm range. A cell study revealed adhering pre-osteogenic MC3T3 cells, with a morphology similar to that of cells seeded on a tissue culture plastic control. The investigated coatings could be considered for further investigation due to the ability to tune their mechanical properties while maintaining a smooth surface, together with their promising in vitro cell response.

In vitro and in vivo biocompatibility and bio-tribological properties of the calcium/amorphous-C composite films for bone tissue engineering application

Carbon-and diamond-like-carbon coated Ti alloys hold great promise for tissue engineering applications. Unfortunately, their strong intrinsic stress leads to the adhesion failure of the films. Herein, a series of a-C films with different Ca content were prepared on Ti₆Al₄V via co-sputtering deposition technology. Homogeneous spherical Ca nanoclusters, with an inner diameter of 2-6 nm, were formed in an amorphous carbon matrix. The addition of Ca induced indistinctive variation in either phase composition or topography. However, the introduction of Ca not only improved the mechanical properties of a-C film but also significantly strengthened its adhesion to osteoblasts. The bio-tribological properties of Ca/a-C films were also assessed using a tribometer in FBS solution. The Ca/a-C films exhibited a low friction coefficient of 0.083 and a low wear rate of 1.02-1.24×10^-6 mm³/Nm. The low coefficient of friction (COF) of the Ca/a-C films indicates their superior mechanical properties, making them the promising target of nanocomposite films used in bio-tribological applications. Well-stretched cells and the developed actin filaments were distinctly observed on the Ca/a-C films in the osteoblast cell adhesion experiments. In addition, the Ca/a-C films promoted cell proliferation and showed high cell viability. After being implanted for 4 weeks, the Ca/a-C implant material still adhered well to the muscle tissue, without inducing hyperergic or inflammatory reactions. Collectively, our results suggest that the Ca/a-C film is an ideal mounting material for bone tissue engineering.

Research on in vitro and in vivo biocompatibility of the low-friction Ti+C/amorphous carbon gradient multilayer films for hard tissue engineering

Ti+C/amorphous carbon (a-C) gradient multilayer (GM) films are prepared on the Ti-alloy substrates via physical vapor deposition. Transmission electron microscopy revealed that the Ti atoms combine with the a-C film to form a TiC phase in the inner layer and the sputtering current significantly influences the amount of the TiC phase. Further, the mechanical properties of the Ti+C/a-C GM films were obtained using nanoindentation, and the results denoted the significant improvement in the mechanical properties of the a-C film after adding the Ti+C transition layers. The hardness and elastic modulus of the a-C GM films became approximately 31 and 265 GPa, respectively, which were obviously greater than those of the a-C films. The biotribological properties of the a-C GM films in fetal bovine serum (FBS) were verified. The coefficient of friction (COF) and wear rate of the obtained Ti+C/a-C GM film were 0.057 and (1.06-1.24) × 10^-6 mm³/(N m), respectively, which were lower than those of pure a-C and the bare Ti alloy. The excellent mechanical properties of the Ti+C gradient transition layer and the lubricating effect of the FBS medium caused the low COF of the a-C GM films, indicating the potential biotribology applications of the a-C films. The cell apoptosis tests suggested that the a-C GM films promoted cell proliferation and viability. Meanwhile, the a-C-GM-coated implants and muscle tissue combined, and hyperergic and inflammatory reactions were not observed six weeks after implantation. These data indicate that the Ti+C/a-C GM film exhibits good biocompatibility and is an ideal mounting material for bone tissue engineering.

A conducive bioceramic/polymer composite biomaterial for diabetic wound healing

Diabetic wound is a common complication of diabetes. Biomaterials offer great promise in inducing tissue regeneration for chronic wound healing. Herein, we reported a conducive Poly (caprolactone) (PCL)/gelatin nanofibrous composite scaffold containing silicate-based bioceramic particles (Nagelschmidtite, NAGEL, Ca₇P₂Si₂O₁₆) for diabetic wound healing. NAGEL bioceramic particles were well distributed in the inner of PCL/gelatin nanofibers via co-electrospinning process and the Si ions maintained a sustained release from the composite scaffolds during the degradation process. The nanofibrous scaffolds significantly promoted the adhesion, proliferation and migration of human umbilical vein endothelial cells (HUVECs) and human keratinocytes (HaCaTs) in vitro. The in vivo study demonstrated that the scaffolds distinctly induced the angiogenesis, collagen deposition and re-epithelialization in the wound sites of diabetic mice model, as well as inhibited inflammation reaction. The mechanism for nanofibrous composite scaffolds accelerating diabetic wound healing is related to the activation of epithelial to mesenchymal transition (EMT) and endothelial to mesenchymal transition (EndMT) pathway in vivo and in vitro. Our results suggest that the released Si ions and nanofibrous structure of scaffolds have a synergetic effect on the improved efficiency of diabetic wound healing, paving the way to design functional biomaterials for tissue engineering and wound healing applications.

STATEMENT OF SIGNIFICANCE

In order to stimulate tissue regeneration for chronic wound healing, a new kind of conducive nanofibrous composite scaffold containing silicate-based bioceramic particles (Nagelschmidtite, NAGEL, Ca₇P₂Si₂O₁₆) were prepared via co-electrospinning process. Biological assessments revealed that the NAGEL bioceramic particles could active epithelial to mesenchymal transition (EMT) and endothelial to mesenchymal transition (EndMT) pathway in vitro and in vivo. The new composite scaffold had potential as functional biomaterials for tissue engineering and wound healing applications. The strategy of introducing controllable amount of therapeutic ions instead of loading expensive drugs/growth factors on nanofibrous composite scaffold provides new options for bioactive biomaterials.