Dynamic thermomechanical properties and sorption characteristics of two commercial light cured dental resin composites

Evaluation of the Impact of Irradiance Lamps and Storage Media on Elution of TEGDMA from Dental Composites

OBJECTIVES

 The aim of this study was to evaluate and compare the effect of irradiance light and storage media on the elution of triethylene glycol dimethacrylate (TEGDMA) from conventional Filtek Z350XT 3M ESPE and two bulk-fill composites Shofu Beautifil-Bulk and Filtek Bulk fill flowable 3M ESPE using high-performance liquid chromatography (HPLC).

MATERIALS AND METHODS

 Shofu Beautifil-Bulk, Filtek Bulk fill flowable 3M ESPE, and Filtek Z350XT 3M ESPE were the three types of composites used in this study. Disk shaped samples of 4-mm thickness and 10-mm diameter were fabricated using a stainless steel mold and were polymerized using light emitting diode (LED) and quartz tungsten halogen (QTH) lamps. After polymerization, the samples were immersed in ethanol, artificial saliva with betel quid extract, and distilled water for 1, 7, and 30 days, respectively. The elution of monomer TEGDMA was evaluated using HPLC.

STATISTICAL ANALYSIS

 To evaluate the mean concentration difference, mixed way analysis of variance (ANOVA) was applied. Between different light, materials, and within the time duration, Tukey's post hoc test was used. A p value of 0.05 was considered significant.

RESULTS

 During the first day of storage, a significant amount of monomer TEGDMA elution was seen in all the materials. The highest values observed to be in the disks cured with QTH lamp. However, the highest elution was seen when the disks were immersed in ethanol/water solution. While the most stable medium was distilled water, artificial saliva with betel nut extract also had a significant effect on the elution of TEGDMA. The highest value obtained was of Filtek Bulk fill flowable 3M ESPE after 30 days of immersion in both LED and QTH cured disks.

CONCLUSION

 Filtek Bulk fill flowable 3M ESPE shows better properties in relation to the release of monomer TEGDMA as it releases less amount of monomer in the storage media. The release of monomer was highest in ethanol as compared to artificial saliva and distilled water with the passage of time.

Do mouthwashes affect the optical properties of resin cement?

OBJECTIVES

The objective of this study was to evaluate the effect of mouthwashes on the optical properties of resin cement.

MATERIALS AND METHODS

One hundred and 60 resin cement discs (6x2mm) were produced from 4 different brands of resin cement (Panavia V5, Estecem II, RelyX Veneer, NX3) with the help of a Teflon mould. The discs were divided into 4 subgroups, 1 of which served as the control group, to be immersed in mouthwashes after measuring the initial L, a, and b values on white and black backgrounds. Colour measurements were repeated after the 1st and 7th days. The collected data were used to calculate the ∆E00 value to measure colour stability, the translucency parameter (TP00), and the contrast ratio parameter (CR) to compare translucency change. Data were statistically analysed using mixed-design analysis of ANOVA and the Bonferroni-Dunn test. Repeated measures ANOVA was used for dependent results (α = 0.05).

RESULTS

On the ∆E00, TP00, and CR parameters; the joint effect of resin groups, mouthwash groups, and measurement times were found to be statistically significant. The ∆E00 (colour difference) parameter; the joint effect of resin groups, mouthwash groups, and measurement times was found to be statistically significant. The TP00; the joint effect of resin groups, mouthwash groups, and measurement times were found to be statistically significant. The CR parameter; the joint effect of resin groups, mouthwash groups, and measurement times was found to be statistically significant. In the Estecem II (Tokuyama) group, the means of Listerine Cool Mint (Johnson & Johnson) was above acceptable limits in both time periods. In the Panavia V5 (Kuraray Noritake) group, the color change was above acceptable limits in all time periods and in all mouthwash groups. Among the resin materials used, Estecem II (Tokuyama) shows the most color change. Listerine Cool Mint (Johnson & Johnson) caused more color change than other mouthwashes at all times.

CONCLUSIONS

Within the limitations of this study; the colour stability and translucency value of resin cement depend on both the resin cement content and the mouthwash. Long-term use of mouthwash may adversely affect the optical properties of the resin cement.

CLINICAL RELEVANCE

Clinicians should take into account the fact that mouthwash use and the composition of the resin cement employed will have an impact on the colour of laminate veneers.

Influence of Specimen Dimension, Water Immersion Protocol, and Surface Roughness on Water Sorption and Solubility of Resin-Based Restorative Materials

The evaluation of water sorption and solubility is pivotal for the development of new resin-based restorative materials with the potential for clinical application. The purpose of the present study was to evaluate the influence of the specimen dimension, water immersion protocol, and surface roughness on the water sorption and solubility of three resin-based restorative materials. Disk-shaped specimens of 15 mm × 1 mm, 10 mm × 1 mm, and 6 mm × 1 mm were produced with a composite resin (Z100), a resin cement (RelyX ARC), and an adhesive system (Single Bond 2-SB2). The specimens were immersed in distilled water according to four protocols: ISO (all the specimens for each group were vertically immersed in 50 mL); IV-10 (the specimens were individually and vertically immersed in 10 mL); IH-10 (the specimens were individually and horizontally immersed in 10 mL); and IH-2 (the specimens were individually and horizontally immersed in 2 mL). The surface roughness (Sa and Sp) was evaluated using an atomic force microscope, and the degree of conversion was determined using FT-IR spectrometry. The specimen dimension and water immersion protocol had no effect on water sorption and solubility. For the three resin-based restorative materials, Sp was higher than Sa. The degree of conversion was not influenced by the specimen dimension. The variations in the specimen dimension and water immersion protocol compared to those determined by ISO 4049 did not prevent the comparison between the values of water sorption and solubility obtained for a given resin-based restorative material.

Formulation, Configuration, and Physical Properties of Dental Composite Resin Containing a Novel 2π + 2π Photodimerized Crosslinker - Cinnamyl Methacrylate: An In Vitro Research

AIM

To formulate and characterize the chemical structure of a new dental composite with photodimerized cinnamyl methacrylate (PD-CMA) photo-crosslinking comonomer and to evaluate the monomer-to-polymer conversion (MPC) and glass transition temperature (Tg) of the new composite copolymers.

MATERIALS AND METHODS

CMA was PD by ultraviolet C-type (UVC) irradiation. The research groups were a control group C0 without PD-CMA and two trial groups: E10 (10 wt. % PD-CMA substituted in the base comonomers (B) and diluent (D) mixture); E20 (20 wt.% PD-CMA completely replacing the diluent (D) monomer). Infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopies were employed for ascertaining copolymerization (CP). The surface features and composition of the copolymers were explained by field-emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) spectroscopy, respectively. The MPC and Tg of the copolymers were assessed using FTIR and differential scanning calorimetry, respectively. Statistical tests were used to compare the groups.

RESULTS

The configuration of the new copolymers P (BD-Co-CMA) and P(B-Co-CMA) was confirmed. The MPC% and T g of the copolymers were better than the control. PD-CMA at 20 wt. % in the P (B-Co-CMA) copolymer exhibited the highest MPC% and Tg.

CONCLUSION

The incorporation of PD-CMA in the composite resin resulted in new P (BD-Co-CMA) and P (B-Co-CMA) copolymers with improved MPC% and Tg.

CLINICAL SIGNIFICANCE

The substitution with PD-CMA offset the shortcomings of the conventional BD comonomers concerning the mechanical properties and biocompatibility of the restorative composite resin. This might ameliorate the restorations in vivo longevity and serviceability.

Influence of thermal and thermomechanical stimuli on a molar tooth treated with resin-based restorative dental composites

OBJECTIVES

In-vivo experimental techniques to understand the biomechanical behavior of a restored tooth, under varying oral conditions, is very limited because of the invasive nature of the study and complex tooth geometry structure. Therefore, 3D-Finite element analyses are used to understand the behavior of a restored tooth under varying oral conditions. In this study, the distribution of maximum principal stress (MaxPS) and the location of MaxPS on a restored tooth using six different commercially available dental resin composites under the influence of thermal and thermomechanical stimuli are performed.

METHODS

An intact tooth was scanned using µ-CT and segmented to obtain separate geometric models of the tooth, including enamel and dentine. Then, a class II mesial-occlusal-distal (MOD) cavity was constructed for the tooth model. The restored tooth model was further meshed and imported to the commercial Finite Element (FE) software ANSYS. Thermal hot and cold stimuli at 50 °C and 2 °C, respectively, were applied on the occlusal and lingual surface of the tooth model with the tooth's ambient temperature set at 37 °C. A uniform loading of 400 N was applied on the occlusal surface of the tooth to imitate the masticatory forces during the cyclic thermal stimuli.

RESULTS

The results of this study showed that the restorative materials with higher thermal conductivity showed a lower temperature gradient between the restoration and enamel, during the application of thermal stimuli, leading to a higher value of MaxPS on the restoration. Moreover, on applying thermal stimuli, the location of MaxPS at the restoration-enamel junction (REJ) changes based on the value of the coefficient of thermal expansion (CTE). The MaxPS distribution on the application of simultaneous thermal and mechanical stimuli was not only dependent on the elastic modulus of restorative materials but also their thermal properties such as the CTE and thermal conductivity. The weakest part of the restoration was at the REJ, as it experienced the peak stress level during the application of thermomechanical stimuli.

SIGNIFICANCE

The findings from this study suggest that restorative materials with lower values of elastic modulus, lower coefficient of thermal expansion and higher values of thermal conductivity result in lower stresses on the restoration. The outcomes from this study also suggest that the thermal and mechanical properties of a restorative material can have a considerable effect on the selection of restorative materials by dental clinicians over conventional restorative materials.

Thermoanalytical Investigations on the Influence of Storage Time in Water of Resin-Based CAD/CAM Materials

New resin-based composites and resin-infiltrated ceramics are used to fabricate computer-aided design (CAD) and computer-aided manufacturing (CAM)-based restorations, although little information is available on the long-term performance of these materials. The aim of this investigation was to determine the effects of storage time (24 h, 90 days, 180 days) on the thermophysical properties of resin-based CAD/CAM materials. Thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) were used in the study. TGA provided insight into the composition of the resin-based materials and the influence of internal plasticization and water sorption. Resin-based composites showed different decomposition, heat energy and mechanical behavior, which was influenced by storage time in water. Individual materials such as Grandio bloc showed lower influence of water storage while maintaining good mechanical properties.

Influence of artificial aging: mechanical and physicochemical properties of dental composites under static and dynamic compression

OBJECTIVE

The aim of the study was to evaluate the influence of filler content, degradation media and time on the mechanical properties of different dental composites after in vitro aging.

MATERIALS AND METHODS

Specimens (1 mm³) of three commercially available composites (GrandioSO®, Arabesk Top®, Arabesk Flow®) with respect to their filler content were stored in artificial aging media: artificial saliva, ethanol (60%), lactic acid (pH 5) and citric acid (pH 5). Parameters (Vickers microhardness, compressive strength, elastic modulus, water sorption and solubility) were determined in their initial state (control group, n = 3 for microhardness, n = 5 for the other parameters) and after 14, 30, 90 and 180 days (n = 3 for microhardness, n = 5 for the other parameters for each composite group, time point and media). Specimens were also characterized with dynamic-mechanical-thermal analysis (compression tests, F =  ± 7 N; f = 0.5 Hz, 1 Hz and 3.3 Hz; t = 0-170 °C).

RESULTS

Incorporation of fillers with more than 80 w% leads to significantly better mechanical properties under static and dynamic compression tests and a better water sorption behavior, even after chemical degradation. The influence of degradation media and time is of subordinate importance for chemical degradation.

CONCLUSION

Although the investigated composites have a similar matrix, they showed different degradation behavior. Since dentine and enamel occur only in small layer thickness, a test specimen geometry with very small dimensions is recommended for direct comparison. Moreover, the use of compression tests to determine the mechanical parameters for the development of structure-compatible and functionally adapted composites makes sense as an additional standard. Clinical relevance Preferential use of highly filled composites for occlusal fillings is recommended.

Regional ultimate tensile strength and water sorption/solubility of bulk-fill and conventional resin composites: The effect of long-term water storage

The effect of long-term water storage on the regional ultimate tensile strength (UTS), water sorption (W_sp) and water solubility (W_sl) of conventional and bulk-fill resin composites at various depths was investigated. Composite specimens light-cured from one side were sectioned into beams corresponding to different depths (1-5 mm) and stored in water for 24 h, 1 week, 1 month, 6 months or 1 year. UTS increased during the first week and then gradually decreased over time, especially in deeper regions. Bulk-fill composites initially exhibited similar UTS at all depths, whereas the UTS of conventional composites at 1 mm and 5 mm differed significantly at all time points. W_sp and W_sl increased with depth and storage time, markedly at 3-5 mm after 1 month for conventional composites and after 6 months for bulk-fill composites. The signs of degradation at depths beyond 3 mm suggested that even bulk-fill composites have suboptimal properties in layers more than 3 mm in thickness.

Physical and Mechanical Properties of Resins Blends Containing a Monomethacrylate with Low-polymerization Shrinkage

Objectives  The aim of this study was to evaluate the Knoop hardness (KH), cross-link density (CLD), water sorption (WS), water solubility (WSB), and volumetric shrinkage (VS) of experimental resins blends containing a monomethacrylate with low-polymerization shrinkage.

Materials and Methods  A blend of bisphenol glycidyl methacrylate (BisGMA) as base monomer was formulated with (Bis-GMA)/triethyleneglycol dimethacrylate (TEGDMA), Bis-GMA/isobornyl methacrylate (IBOMA), or Bis-GMA/TEGDMA/IBOMA in different concentrations (40, 50, or 60 wt%). The camphorquinone (CQ)/2-(dimethylamino) ethyl methacrylate (DMAEMA) was used as the photoinitiator system. The KH and CLD were measured at the top surface using an indenter. For WS and WSB, the volume of the samples was calculated in mm ³ . The samples were transferred to desiccators until a constant mass was obtained (m1) and were subsequently immersed in distilled water until no alteration in mass was detected (m2). The samples were reconditioned to constant mass in desiccators (m3). WS and WSB were determined using the equations m2 − m3/V and m1 − m3/V, respectively. VS results were calculated with the density parameters before and after curing.

Statistical Analysis  Data were submitted to ANOVA and Tukey’s test (α = 0.05).

Results  The resins containing IBOMA showed lower VS results. TEGDMA 40% and TEGDMA/IBOMA 20/20 wt% showed higher KH values. The IBOMA groups showed lower CLD, while TEGDMA groups had higher values of CLD. The BisGMA/TEGDMA resin presented the highest values of WS, and for WSB, all groups showed no significant differences among themselves.

Conclusion  The monomethacrylate with low-polymerization shrinkage IBOMA used alone or in combination with TEGDMA may decrease VS, WS, and CLD values.

Microwave assisted urethane grafted nano-apatites for dental adhesives

The objectives were to synthesize urethane grafted nano-apatite in shortest possible time duration using the microwave irradiation method and to utilize them for synthesis of experimental dental adhesives. The structural, morphological, thermal, and mechanical behavior of synthesized grafted nano-apatite were investigated. Then, these grafted nano-apatite particles were incorporated in various concentrations that is, 5wt.%, 10wt.%, and 15wt.% into dimethacrylate resins to develop bioactive adhesives. The weight measurement analysis in deionized water and phosphate buffer saline, Knoop micro-hardness, and degree of conversion were evaluated. The bacterial adhesion was investigated with Streptococcus mutans at 6h, 24h, and 48h. Statistical analysis was conducted using one-way ANOVA. The urethane dimethacrylate was successfully grafted on the nano-apatite surface and spectroscopic analysis confirmed the presence of urethane and phosphate peaks. An inverse relationship was found in both media between the concentration of grafted fillers and weight loss. No significant difference was observed in the micro-hardness and degree of conversion among the groups, whereby the degree of conversion for all groups was in the range of 83% to 86%. The mean number of bacterial colonies was significantly lower in the 15wt.% group compared to 5wt.% and 10wt.%. The grafted nano-apatite presented favorable results for adhesive resin incorporation, where 15wt.% group comparatively showed superior results than other groups.

A Guide through the Dental Dimethacrylate Polymer Network Structural Characterization and Interpretation of Physico-Mechanical Properties

Material characterization by the determination of relationships between structure and properties at different scales is essential for contemporary material engineering. This review article provides a summary of such studies on dimethacrylate polymer networks. These polymers serve as photocuring organic matrices in the composite dental restorative materials. The polymer network structure was discussed from the perspective of the following three aspects: the chemical structure, molecular structure (characterized by the degree of conversion and crosslink density (chemical as well as physical)), and supramolecular structure (characterized by the microgel agglomerate dimensions). Instrumental techniques and methodologies currently used for the determination of particular structural parameters were summarized. The influence of those parameters as well as the role of hydrogen bonding on basic mechanical properties of dimethacrylate polymer networks were finally demonstrated. Mechanical strength, modulus of elasticity, hardness, and impact resistance were discussed. The issue of the relationship between chemical structure and water sorption was also addressed.

Effect of trifluoroethyl methacrylate comonomer on physical properties of Bis-GMA based dental composites

The purpose of this study was to investigate the effect of substituting triethyleneglycol dimethacrylate (TEGDMA) with 2,2,2-trifluoroethyl methacrylate (TFEMA) on water sorption, water solubility, degree of conversion, polymerization shrinkage, fluoride release and flexural strength of bisphenol-A-glycerolate dimethacrylate (Bis-GMA)/TEGDMA/urethane dimethacrylate (UDMA) dental composites. Flexural strength, water sorption and water solubility were measured according to ISO 4049 standard. Degree of conversion was determined by FTIR technique. Fluoride release rate in deionized water at 37°C was determined by using photometric method. One-way ANOVA and Tukey's HSD tests were used for statistical significance analysis (p<0.05). The results demonstrated that TFEMA decreased water solubility and volumetric shrinkage significantly but neither reduced water sorption, enhanced flexural strength nor improved degree of conversion. Partial substitution of TEGDMA with TFEMA in Bis-GMA/TEGDMA/UDMA dental composite had positive effect on its water solubility and volumetric shrinkage quality.

TEGDMA releasing in resin composites with different filler contents and its correlation with mitochondrial mediated cytotoxicity in human gingival fibroblasts

Compositions of resin composite exhibit cytotoxicity, especially Triethylene-glycol-dimethacrylate (TEGDMA), yet the underlying mechanisms and its relationship with filler content are poorly understood. Here, specimens of five composites (VITA LC, VITA ZETA, Z350, Filtek P60, and AP-X), containing different filler size and weight, were immersed into culture medium for 72 h. After TEGDMA quantification, the resin composite eluates were used to incubate HGFs. Cellular viability was evaluated. Total reactive oxygen species (ROS) and mitochondrial ROS were detected to assess oxidative stress. Adenosine triphosphate and cytochrome c oxidase (CcO) activity, mitochondrial membrane potential and morphology, mitochondrial biogenesis regulators were analyzed to evaluate mitochondrial functions. Results showed that TEGDMA release negatively correlated to filler size and weight of tested composites. Although cell viability reduction was not significant, total and mitochondrial ROS production showed a positive relationship with the amount of TEGDMA in composite eluates. Furthermore, the expression of mitochondrial biogenesis markers and mitochondrial fusion protein, were markedly elevated in TEGDMA rich eluates, especially in VITA-LC group, shown as elongated mitochondrial morphology and aberrant mitochondrial functions. Overall, TEGDMA could elute easier from those resin composites with less filler content and cause oxidative stress in HGFs via mitochondria dysregulation. These data can be instructive to optimize the synthesis of resin composites from the perspective of biocompatibility. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 107A: 1132-1142, 2019.

Photopolymerizable and moisture-curable polyurethanes for dental adhesive applications to increase restoration durability

In this study we evaluated dual-cure polyurethanes (PUs) as dental adhesives and investigated their effect on the durability of the resin-dentin bonding interface. Different novel photopolymerizable and moisture-curable PUs based on polyester polyol, polyether polyol, and hydroxyethyl methacrylates (HEMAs) were prepared, and their structural characteristics were evaluated by Fourier transform infrared spectroscopy. The tensile strength, elongation at break, and water sorption/solubility of the PU adhesives and the application for bonding with dentin were evaluated. The water sorption and solubility of the PU adhesives were significantly lower than those of two commercial control groups. The bond strength of the PU adhesives after 30 days of storage increased compared with their immediate bond strength, and the microleakage detection of Class V restorations showed less occurrence of marginal leakage compared with the commercial control groups. Cytotoxicity testing has shown that the PU adhesives have low toxicity to pulp cells. The results of this study may shift the future research focus of composite resin dental restoratives from original rigid bonding of the interface to a flexible bonding based on the use of PU adhesives. This may become a new strategy for decreasing the occurrence of microleakage and improving the durability of the bonding interface.

Fabrication of hybrid crosslinked network with buffering capabilities and autonomous strengthening characteristics for dental adhesives

Ingress of bacteria and fluids at the interfacial gaps between the restorative composite biomaterial and the tooth structure contribute to recurrent decay and failure of the composite restoration. The inability of the material to increase the pH at the composite/tooth interface facilitates the outgrowth of bacteria. Neutralizing the microenvironment at the tooth/composite interface offers promise for reducing the damage provoked by cariogenic and aciduric bacteria. We address this problem by designing a dental adhesive composed of hybrid network to provide buffering and autonomous strengthening simultaneously. Two amino functional silanes, 2-hydroxy-3-morpholinopropyl (3-(triethoxysilyl)propyl) carbamate and 2-hydroxy-3-morpholinopropyl (3-(trimethoxysilyl)propyl) carbamate were synthesized and used as co-monomers. Combining free radical initiated polymerization (polymethacrylate-based network) and photoacid-induced sol-gel reaction (polysiloxane) results in the hybrid network formation. Resulting formulations were characterized with regard to real-time photo-polymerization, water sorption, leached species, neutralization, and mechanical properties. Results from real-time FTIR spectroscopic studies indicated that ethoxy was less reactive than methoxy substituent. The neutralization results demonstrated that the methoxy-containing adhesives have acute and delayed buffering capabilities. The mechanical properties of synthetic copolymers tested in dry conditions were improved via condensation reaction of the hydrolyzed organosilanes. The leaching from methoxy containing copolymers was significantly reduced. The sol-gel reaction provided a chronic and persistent reaction in wet condition-performance that offers potential for reducing secondary decay and increasing the functional lifetime of dental adhesives.

STATEMENT OF SIGNIFICANCE

The interfacial gaps between the restorative composite biomaterial and the tooth structure contributes to recurrent decay and failure of the composite restoration. The inability of the material to increase the pH at the composite/tooth interface facilitates the outgrowth of more cariogenic and aciduric bacteria. This paper reports a novel, synthetic resin that provides buffering capability and autonomous strengthening characteristics. In this work, two amino functional silanes were synthesized and the effect of alkoxy substitutions on the photoacid-induced sol-gel reaction was investigated. We evaluated the neutralization capability (monitoring the pH of lactic acid solution) and the autonomous strengthening property (monitoring the mechanical properties of the hybrid copolymers under wet conditions and quantitatively analyzing the leachable species by HPLC). The novel resin investigated in this study offers the potential benefits of reducing the risk of recurrent decay and prolonging the functional lifetime of dental adhesives.

The electrical properties and glass transition of some dental materials after temperature exposure

The physicochemical properties of dental materials will remain stable only when these materials in question are resistant to the changes in the oral cavity. The oral environment is subject to large temperature variations. The aim of the study was the assessment of electrical properties and glass transition of some dental materials after temperature exposure. Composite materials, compomers, materials for temporary prosthetic replacement and resin-based pit and fissure sealants were used in the study. The method used was electric conductivity of materials under changing temperature. The order of materials presenting the best characteristics for insulators was as follows: materials for temporary prosthetic replacement, resin-based pit and fissure sealants, composites, and compomers. Thanks to comparisons made between graphs during I and II heating run, the method could be used to observe changes in the heated material and determine whether the changes observed are reversible or permanent. The graphs also provided temperature values which contain information on glass transition during heating. In the oral cavity the effect of the constant temperature stimulus influences maturity of dental materials and improves their properties. But high temperatures over glass transition temperature can cause irreversible deformation and changes of the materials properties, even in a short time.

The Influence of Water Sorption of Dental Light-Cured Composites on Shrinkage Stress

The contraction stress generated during the photopolymerization of resin dental composites is the major disadvantage. The water sorption in the oral environment should counteract the contraction stress. The purpose was to evaluate the influence of the water sorption of composite materials on polymerization shrinkage stress generated at the restoration-tooth interface. The following materials were tested: Filtek Ultimate, Gradia Direct LoFlo, Heliomolar Flow, Tetric EvoCeram, Tetric EvoCeram Bulk Fill, Tetric EvoFlow, Tetric EvoFlow Bulk Fill, X-tra Base, Venus BulkFil, and Ceram.X One. The shrinkage stress was measured immediately after curing and after: 0.5 h, 24 h, 72 h, 96 h, 168 h, 240 h, 336 h, 504 h, 672 h, and 1344 h by means of photoelastic study. Moreover, water sorption and solubility were evaluated. Material samples were weighted on scale in time intervals to measure the water absorbency and the dynamic of this process. The tested materials during polymerization generated shrinkage stresses ranging from 6.3 MPa to 12.5 MPa. Upon water conditioning (56 days), the decrease in shrinkage strain (not less than 48%) was observed. The decrease in value stress in time is material-dependent.

Full in-vitro analyses of new-generation bulk fill dental composites cured by halogen light

The objective of this study was to investigate the full in-vitro analyses of new-generation bulk-fill dental composites cured by halogen light (HLG). Two types' four composites were studied: Surefill SDR (SDR) and Xtra Base (XB) as bulk-fill flowable materials; QuixFill (QF) and XtraFill (XF) as packable bulk-fill materials. Samples were prepared for each analysis and test by applying the same procedure, but with different diameters and thicknesses appropriate to the analysis and test requirements. Thermal properties were determined by thermogravimetric analysis (TG/DTG) and differential scanning calorimetry (DSC) analysis; the Vickers microhardness (VHN) was measured after 1, 7, 15 and 30days of storage in water. The degree of conversion values for the materials (DC, %) were immediately measured using near-infrared spectroscopy (FT-IR). The surface morphology of the composites was investigated by scanning electron microscopes (SEM) and atomic-force microscopy (AFM) analyses. The sorption and solubility measurements were also performed after 1, 7, 15 and 30days of storage in water. In addition to his, the data were statistically analyzed using one-way analysis of variance, and both the Newman Keuls and Tukey multiple comparison tests. The statistical significance level was established at p<0.05. According to the ISO 4049 standards, all the tested materials showed acceptable water sorption and solubility, and a halogen light source was an option to polymerize bulk-fill, resin-based dental composites.

Synthesis and characterization of a novel resin monomer with low viscosity

OBJECTIVE

In this study, we designed and synthesized a novel macromolecule (tetramethyl bisphenol F acrylate, TMBPF-Ac) with low viscosity, excellent mechanical properties, and good biocompatibility. It could be used as a monomer for dental resin composites, which could reduce the risk of human exposure to bisphenol A derivatives in the oral environment. In addition, the monomer could be used without diluent, thereby avoiding the negative effect of a diluent METHODS: TMBPF-Ac was synthesized by a multistep condensation reaction. Its structure was confirmed by ¹H NMR spectra. Different resin mixtures were prepared, and then a number of performance and cytotoxicity tests were performed on these specimens.

RESULTS

¹H NMR spectra showed that the structure of TMBPF-Ac was in accordance with the design. The viscosity of TMBPF-Ac was obviously lower than that of bisphenol-A diglycidyl methacrylate. The three kinds of resins used in this study were in line with ISO 4049:2009 and ISO 10993-5:2009. TMBPF-Ac-based resin had better physical and biological properties.

Dynamic thermo-mechanical properties of various flowable resin composites

Background

This study compared the storage modulus (E’), the loss modulus (E’’) and the loss tangent (tan δ) of various flowable resin composites.

Material and Methods

Grandio Flow (GRF), GrandioSo Heavy Flow (GHF), Filtek Supreme XTE (XTE) and Filtek Bulk Fill (BUL) flowable resins and Clinpro Sealant (CLI) ultra-flowable pit and fissure sealant resin were used. 25 samples were tested using a dynamical mechanical thermal analysis system in bending mode. Measurements were taken within a temperature range of 10 to 55°C. The results were statistically analyzed using mixed-effect and repeated-measure analysis of variance followed by paired multiple comparisons.

Results

For all the materials, the E’ values decrease with temperature, whereas the tan δ values increase. Irrespective of the temperature, GHF and GRF present E’ and E’’ values significantly higher than all the other materials and CLI presents values significantly lower than all the other materials. Observation of the values for all the materials reveals a linear progression of the tan δ values with temperature.

Conclusions

A variation in temperature within a physiological range generates modifications in mechanical properties without damaging the material, however. Filler content in volume terms appears to be the crucial parameter in the mechanical behavior of tested materials.

Key words:Dynamic mechanical thermal analysis, elastic modulus, filler content, flowable resin composites, loss modulus, loss tangent.

Preparation of a Bis-GMA-Free Dental Resin System with Synthesized Fluorinated Dimethacrylate Monomers

With the aim of reducing human exposure to Bisphenol A (BPA) derivatives in dentistry, a fluorinated dimethacrylate monomer was synthesized to replace 2,2-bis[4-(2-hydroxy-3-methacryloy-loxypropyl)-phenyl]propane (Bis-GMA) as the base monomer of dental resin. After mixing with reactive diluent triethyleneglycol dimethacrylate (TEGDMA), fluorinated dimethacrylate (FDMA)/TEGDMA was prepared and compared with Bis-GMA/TEGDMA in physicochemical properties, such as double bond conversion (DC), volumetric shrinkage (VS), water sorption (WS) and solubility (WSL), flexural strength (FS) and modulus (FM). The results showed that, when compared with Bis-GMA based resin, FDMA-based resin had several advantages, such as higher DC, lower VS, lower WS, and higher FS after water immersion. All of these revealed that FDMA had potential to be used as a substitute for Bis-GMA. Of course, many more studies, such as biocompatibility testing, should be undertaken to prove whether FDMA could be applied in clinic.

Cytotoxicity of Experimental Resin Composites on Mesenchymal Stem Cells Isolated from Two Oral Sources

Resin composite materials that are used to restore tooth cervical lesions associated with gingival recessions can hamper healing after root coverage surgeries. This study evaluates the in vitro cytotoxic effect of five resin composites (two commercial and three experimental) on oral mesenchymal stem cells (MSCs) and the persistence of stemness properties in high passage MSCs. Sorption and solubility tests were made for all materials. MSCs were isolated from re-entry palatal and periodontal granulation tissues and were characterized and cultured on composite discs. Cytotoxicity of the materials was evaluated by the Alamar Blue viability test, by Paul Karl Horan (PKH) labeling, and by immunocytochemical staining for actin. Water and saliva sorption and solubility data revealed that two of the experimental materials behaved comparable with the marketed resin composites. The Alamar Blue viability test shows that both cell lines grew well on composite discs that seemed to induce no apparent toxic effects. No signs of disruption of cytoskeleton organization was seen. Experimental resin composites can be recommended for further investigation for obtaining approval for use. The standard minimal criteria were fulfilled for high passage MSCs. Palatal tissue regains its regenerative properties in terms of MSC presence in the re-entry area after 6 months of healing.

Preparation and characterization of Bis-GMA free dental resin system with synthesized dimethacrylate monomer TDDMMA derived from tricyclo[5.2.1.0(2,6)]-decanedimethanol

As a substitute for 2,2-bis[4-(2-hydroxy-3- methacryloxypropoxy)phenyl] propane (Bis-GMA) in dental materials, a new dimethacrylate monomer TDDMMA without bisphenol-A structure was synthesized through the reaction between tricyclo[5.2.1.0(2,6)]- decanedimethanol and 2-isocyanatoethyl methacrylate. The TDDMMA was mixed with triethylene glycol dimethacrylate (TEGDMA) to prepare Bis-GMA free dental resin. Physicochemical properties, such as double bond conversion (DC), polymerization shrinkage (VS), water sorption (WS) and solubility (SL), flexural strength (FS) and modulus (FM) and fracture energy of TDDMMA/TEGDMA resin system were investigated. Bis-GMA/TEGDMA resin system was used as a control. The results showed that, compared with Bis-GMA/TEGDMA resin system, TDDMMA/TEGDMA resin system had comparable VS and several advantages like higher DC, lower SL and better mechanical properties after water immersion.

Compositional design and optimization of dentin adhesive with neutralization capability

OBJECTIVES

The objective of this work was to investigate the polymerization behavior, neutralization capability, and mechanical properties of dentin adhesive formulations with the addition of the tertiary amine co-monomer, 2-N-morpholinoethyl methacrylate (MEMA).

METHODS

A co-monomer mixture based on HEMA/BisGMA (45/55, w/w) was used as a control adhesive. Compared with the control formulation, the MEMA-containing adhesive formulations were characterized comprehensively with regard to water miscibility of liquid resin, water sorption and solubility of cured polymer, real-time photopolymerization kinetics, dynamic mechanical analysis (DMA), and modulated differential scanning calorimetry (MDSC). The neutralization capacity was characterized by monitoring the pH shift of 1mM lactic acid (LA) solution, in which the adhesive polymers were soaked.

RESULTS

With increasing MEMA concentrations, experimental copolymers showed higher water sorption, lower glass transition temperature and lower crosslinking density compared to the control. The pH values of LA solution gradually increased from 3.5 to about 6.0-6.5 after 90 days. With the increase in crosslinking density of the copolymers, the neutralization rate was depressed. The optimal MEMA concentration was between 20 and 40 wt%.

CONCLUSIONS

As compared to the control, the results indicated that the MEMA-functionalized copolymer showed neutralization capability. The crosslinking density of the copolymer networks influenced the neutralization rate.

Sorption characteristics of oral/food simulating liquids by the dental light-cured nanohybrid composite Kalore GC

OBJECTIVE

This work presents the results obtained from the study of sorption/desorption process of some food/oral simulating liquids (FSLs) by the new marketed dental light-cured nanohybrid composite Kalore GC.

METHODS

The sorption/desorption process followed is recommended by ISO 4049:2009. The samples were immersed in various liquids proposed by ADA as FSLs, such as H2O, artificial saliva, EtOH, EtOH/H2O solution (75vol%) or C7H16, while the mass change for totally 30 days was recorded on defined time intervals. Afterwards the samples were put in dry desiccators at 37°C for the study of desorption process.

RESULTS

The weight percentage of sorption of the above mentioned FSLs by Kalore GC was determined; also the wt% of the desorbed liquid, the diffusion coefficient of sorption and desorption, the wt% solubility and the % volume increase due to the liquid sorption.

SIGNIFICANCE

The sorption characteristics of a dental composite depend both on composite structure and liquid. Ethanol/water and ethanol showed the highest effect on the determined characteristics. Then, the water and SAGF(®) saliva follows and finally the heptane solvent.

Effect of Beverages on Viscoelastic Properties of Resin-Based Dental Composites

The viscoelastic properties of three commercially available resin-based composites (Filtek™ P60, Filtek™ Supreme, and Filtek™ Z250; 3M ESPE, Bracknell, UK) were measured to determine the effect of beverages on their storage moduli and damping ratios. Rectangular samples of the three hybrid composites were immersed in three beverages at 37 °C for 1, 7, 30, and 60 days. At each time interval, these samples were subjected to three-point bend tests in temperature mode using a Perkin Elmer DMA7 Dynamic Mechanical Analyzer (Perkin Elmer Corp., Waltham, MA, USA) to measure the storage modulus and damping ratio. The immersion time had significant influence on the viscoelastic property of composites and it was found that generally for all samples the storage modulus was reduced, whereas damping values increased with immersion time. The viscoelastic behavior of tested materials seems to be related to the pH environment, hydrophilicity and the chemical composition of composites.

A dual role for β1 integrin in an in vitro Streptococcus mitis/human gingival fibroblasts co-culture model in response to TEGDMA

AIM

To evaluate the effect of TEGDMA on human gingival fibroblasts (HGFs) in vitro co-cultured with Streptococcus mitis, focusing on the signalling pathways underlying cell tissue remodelling and inflammatory response processes.

METHODOLOGY

β1 integrin expression was evaluated by means of imaging flow cytometry. The Western blot technique was used to investigate the expression of protein kinase C (PKC), extracellular signal-regulated kinase (ERK), matrix metalloproteinase 9 (MMP9) and 3 (MMP3). RT-PCR was performed to quantify nuclear factor-kb subunits (Nf-kb1, ReLa), IkB kinase β (IkBkB), cyclooxygenase II (COX-2) and tumour necrosis factor-α (TNF-α) mRNA levels. Statistical analysis was performed using the analysis of variance (anova).

RESULTS

When HGFs are co-cultured with S. mitis, β1 integrin intensity, phosphorylated PKC (p-PKC), activated ERK (p-ERK), IkBkB mRNA level and MMP9 expression increased (for all molecules P < 0.05 HGFs versus HGFs co-cultured with S. mitis). A higher level of MMP3 in HGFs treated with TEGDMA was recorded (P < 0.05 HGFs versus HGFs exposed to TEGDMA). COX-2 inflammatory factor mRNA level appeared higher in HGFs exposed to 1 mmol L(-1) TEGDMA (P < 0.01 HGFs versus HGFs exposed to TEGDMA), whereas TNF-α gene expression was higher in HGFs co-cultured with S. mitis (P < 0.05 HGFs versus HGFs co-cultured with S. mitis).

CONCLUSIONS

β1 integrin triggered the signalling pathway, transduced by p-PKCα and involving ERK 1 and 2 and MMPs. This pathway resulted in an unbalanced equilibrium in tissue remodelling process, along with inflammatory response when HGFs are exposed to bacteria or biomaterial alone. On the contrary, the TEGDMA/S. mitis combination restored the balance between extracellular matrix deposition and degradation and prevented an inflammatory response.

Preparation of low shrinkage methacrylate-based resin system without Bisphenol A structure by using a synthesized dendritic macromer (G-IEMA)

With the growing attention on estrogenic effect of Bisphenol A (BPA), the application of BPA derivatives like Bis-GMA in dental materials has also been doubted. In this research, new BPA free dental resin systems were prepared with synthesized dendritic macromer G-IEMA, UDMA, and TEGDMA. Physicochemical properties, such as double bond conversion, polymerization shrinkage, flexural strength and modulus, fracture energy, water sorption and solubility of BPA free resin formulations were investigated. Bis-GMA/TEGDMA resin system was used as a control. Results showed that the prepared BPA free resins could have higher double bond conversion, comparable or lower polymerization shrinkage and water sorption, and lower water solubility, when compared with Bis-GMA/TEGDMA resin. Though flexural strength and modulus of prepared BPA free polymers were lower than those of Bis-GMA/TEGDMA polymer, BPA free polymers had higher fracture energies and showed plastic deformation prior to fracture, all of these two phenomena showed that BPA free polymers in this research might have higher fracture toughness which would be good for the service life of dental materials.

Do new matrix formulations improve resin composite resistance to degradation processes?

The aim of this study was to determine the degradation resistance of three new formulations-silorane-, Ormocer- and dimer-acid-based materials-and compare them to the traditional dimethacrylate-based materials. One silorane- (Filtek P90, P90), one Ormocer- (Ceram-X, CX), one dimer-acid- (N'Durance, ND) and two dimethacrylate-based (Filtek P60, P60; Tetric Ceram, TC) materials were investigated. Water sorption (Wsp) and solubility (Wsl) were determined after the materials were immersed in water for 28 days. Knoop hardness (KH) was determined before and after 24 h immersion in pure ethanol. The flexural-strength (FS) was determined by the bending test after one-week storage in a dry environment or after one-week immersion in pure ethanol. Data were submitted to analysis of variance (ANOVA) and Tukey's test (95%). The three new formulations showed lower Wsp than the dimethacrylate-based formulation. CX (0.50 ± 0.17%) and ND (0.72 ± 0.19%) exhibited the lowest Wsp, whereas P90 (0.02 ± 0.03%) and P60 (0.04 ± 0.03%) showed the lowest Wsl. All resins showed reduced Knoop hardness number (KHN) after ethanol immersion. P60 presented the lowest decrease in KH value (19 ± 5%). TC (48 ± 3%) and P90 (39 ± 9%) showed the highest KHN decrease after ethanol storage. The FS of CX, ND and TC were affected by ethanol storage. The new formulations did not improve the degradation resistance, as compared with the traditional methacrylate-based materials.

Polymerization development of "low-shrink" resin composites: Reaction kinetics, polymerization stress and quality of network

OBJECTIVES

To evaluate "low-shrink" composites in terms of polymerization kinetics, stress development and mechanical properties.

METHODS

"Low-shrink" materials (Kalore/KAL, N'Durance/NDUR, and Filtek P90/P90) and one control (Esthet X HD/EHD) were tested. Polymerization stress (PS) was measured using the Instron 5565 tensometer. Volumetric shrinkage (VS) was determined by the ACTA linometer. Elastic modulus (E) and flexural strength (FS) were obtained by a three-point bending test. Degree of conversion (DC) and polymerization rate (Rp) were determined by NIR spectroscopy (6165cm(-1) for dimethacrylates; 4156 and 4071cm(-1) for P90). Photopolymerization was performed at 740mW/cm(2)×27s. Glass transition temperature (Tg), degree of heterogeneity and crosslink density were obtained in a DMA for the fully cured specimens. Analysis of extracts was done by (1)H NMR. Data were analyzed with one-way ANOVA/Tukey's test (α=0.05).

RESULTS

The control presented the highest shrinkage and Tg. P90 showed the highest modulus, and NDUR demonstrated the highest conversion. The polymerization rates were comparable for all materials. NDUR and KAL had the highest and the lowest network homogeneity, respectively. The multifunctional P90 had the highest crosslink density, with no difference between other composites. The control had the greatest stress development, similar to NDUR. Crosslinking density and polymer network homogeneity were influenced by degree of conversion and monomer structure.

SIGNIFICANCE

Not all "low-shrink" composites reduced polymerization stress. P90 and NDUR had no leachable monomers, which was also a function of high crosslinking (P90) and high conversion (NDUR).

Synthesis of a novel tertiary amine containing urethane dimethacrylate monomer (UDMTA) and its application in dental resin

A novel tertiary amine containing urethane dimethacrylate monomer UDMTA was synthesized with the aim of replacing Bis-GMA as one component of dental restorative materials. The structure of UDMTA was confirmed by FT-IR and (1)H-NMR spectra. UDMTA was incorporated into Bis-GMA/TEGDMA (50 wt%/50 wt%) resin system to replace Bis-GMA partly and totally. Double bond conversion, polymerization volumetric shrinkage, water sorption and solubility, flexural strength and modulus of UDMTA containing resin formulations were studied with neat Bis-GMA/TEGDMA resin formulation as a reference. Results showed that UDMTA could be used as a coinitiator in photocurable dental resin, UDMTA containing resin had higher double bond conversion and lower polymerization shrinkage than that of Bis-GMA/TEGDMA resin, and the UDMTA containing copolymer had higher flexural strength and flexural modulus than Bis-GMA/TEGDMA copolymer. When UDMTA was used to replace more than 25 wt% of Bis-GMA, the obtained copolymer had higher water sorption and solubility. The optimized resin composition is by replacing 25 wt% of Bis-GMA in Bis-GMA/TEGDMA (50/50 by wt%), for the prepared resin had the best comprehensive properties.

FT-Raman spectroscopy study of organic matrix degradation in nanofilled resin composite

This in vitro study evaluated the effect of light curing unit (LCU) type, mouthwashes, and soft drink on chemical degradation of a nanofilled resin composite. Samples (80) were divided into eight groups: halogen LCU, HS--saliva (control); HPT--Pepsi Twist®; HLC--Listerine®; HCP--Colgate Plax®; LED LCU, LS--saliva (control); LPT--Pepsi Twist®; LLC--Listerine®; LCP--Colgate Plax®. The degree of conversion analysis and the measure of the peak area at 2,930 cm-1 (organic matrix) of resin composite were done by Fourier-transform Raman spectroscopy (baseline, after 7 and 14 days). The data were subjected to multifactor analysis of variance (ANOVA) at a 95% confidence followed by Tukey's HSD post-hoc test. The DC ranged from 58.0% (Halogen) to 59.3% (LED) without significance. Differences in the peak area between LCUs were found after 7 days of storage in S and PT. A marked increase in the peak intensity of HLC and LLC groups was found. The soft-start light-activation may influence the chemical degradation of organic matrix in resin composite. Ethanol contained in Listerine® Cool Mint mouthwash had the most significant degradation effect. Raman spectroscopy is shown to be a useful tool to investigate resin composite degradation.

Preparation and evaluation of dental resin with antibacterial and radio-opaque functions

In order to prepare antibacterial and radio-opaque dental resin, a methacrylate monomer named 2-Dimethyl-2-dodecyl-1-methacryloxyethyl ammonium iodine (DDMAI) with both antibacterial and radio-opaque activities was added into a 2,2-bis[4-(2-hydroxy-3-methacryloyloxypropyl)-phenyl]propane (Bis-GMA)/methyl methacrylate (MMA) dental resin system. Degree of conversion (DC), flexural strength (FS) and modulus (FM), water sorption (WS) and solubility (WSL), antibacterial activity, and radio-opacity (ROX) of the obtained dental resin system were investigated. Bis-GMA/MMA resin system without DDMAI was used as a control. The results showed that DDMAI could endow BIS-GMA/MMA resin system with good antibacterial (p < 0.05) and radio-opaque function without influencing the DC (p > 0.05). However, incorporating DDMAI into Bis-GMA/MMA resin could reduce mechanical properties (p < 0.05) and increase WS and WSL (p < 0.05), thus further work is needed in order to optimize the resin formulation.