A randomized controlled 30 years follow up of three conventional resin composites in Class II restorations

The influence of filler load in 3D printing resin-based composites

OBJECTIVE

To evaluate the influence of the barium glass (BG) filler in 3D printing resin-based composites for restorative structures.

METHODS

Experimental 3D printing resin-based composites were formulated with UDMA 70%wt, Bis-EMA 20%wt, and TEGDMA 10%wt. Photoinitiators TPO and DFI (2%wt) were used. BG was incorporated at 40%wt and 50%wt. 0%wt BG was used as negative control and the VarseoSmile Crownplus (Bego) was used as a commercial control. Specimens were printed using a 3D printer. Subsequently, specimens were washed and submitted to post-curing with 405 nm at 60ºC for 2 × 20 min at FormCure (FormLabs). 3D printing resin-based composites were evaluated by flexural strength, degree of conversion, softening in solvent, radiopacity, and cytotoxicity against gingival fibroblasts. Data were statistically analyzed using one-way ANOVA (α = 0.05).

RESULTS

No significant differences in flexural strength were showed between BG40% (90.5 ± 5,4 MPa), BG50% (102.0 ± 11.7 MPa) and VA (105.2 ± 11.7 MPa). Addition of 40% and 50% of BG showed no influence in the degree of conversion compared to VA (p > 0.05). All groups showed softening in solvent after immersion in ethanol (p < 0.05). All groups showed more than 1mmAl of radiopacity. BG50% showed significantly higher radiopacity (2.8 ± 0.3 mmAl) than other groups (p < 0,05). Cytotoxicity evaluation showed gingival cell viability higher than 80% for all groups.

SIGNIFICANCE

Addition of up to 50%wt of barium glass in experimental 3D printing resin-based composites showed promising results for long-term restorative structures.

Flowable bulk-fill versus layering restorative material on Class II restorations: A randomized clinical trial

OBJECTIVE

This study evaluated the clinical performance of Class II restorations made with flowable bulk-fill base versus conventional layering ORMOCER-based restorative material in a split-mouth randomized clinical trial.

METHODS

Thirty patients received two class II restorations (n = 60) performed with different strategies. All preparations received the application of the universal self-etching adhesive system according to the manufacturer's recommendation, followed by the placement of a sectional matrix, wooden wedge, and separation ring. The first restoration was performed using 4 mm of flowable bulk-fill material covered by 2 mm of conventional viscosity restorative material (Bulk-fill technique). The second restoration was performed only with the conventional viscosity material, with a maximum of 2 mm thick increments, up to fill the cavity (Layering technique). After occlusal adjustment, the same polishing system was used for all restorations. Evaluations using the FDI criteria were conducted after 7 days, 12, and 24 months. Data were analyzed with the Fisher's Exact test (α=0.05).

RESULTS

From 30 participants, 24 attended the 24-month recall, and 48 restorations were evaluated. All restorations received acceptable overall scores for esthetic and biological properties after this period, while only 6.66 % of the restorations exhibited unacceptable overall scores for the functional properties in both groups. No significant differences between the tested restorative materials and techniques were found for each FDI criterion assessed. The success rate after 2 years was 93.33 % for both groups.

CONCLUSION

Both restorative materials exhibited good clinical performance for the parameters analyzed with no differences between them after 24-month follow-up.

CLINICAL RELEVANCE

Flowable bulk-fill ORMOCER-based material is a suitable alternative for direct Class II restorations, providing good clinical outcomes and simplifying the restorative procedure.

CLINICAL TRIAL REGISTRATION NUMBER

RBR-6mvp9w.

Long-term clinical comparison of a resin-based composite and resin modified glass ionomer in the treatment of cervical caries lesions

This 72-month study compared the clinical effectiveness of a resin-based composite (RBC) (Spectrum TPH3, Dentsply Sirona) with a resin-modified glass ionomer cement (RMGIC) (Riva Light Cure, SDI) in restoring cervical caries lesions (CCLs). Thirty-three patients, each with at least two CCLs, were enrolled. After caries removal, the dimensions of the cavities were recorded. In a split-mouth study design, a total of 110 restorations were randomly placed. Fifty-five restorations were placed with RBC using an etch-and-rinse adhesive system (Prime&Bond NT, Dentsply Sirona), while the remaining 55 were restored with RMGIC. The restorations were assessed at baseline, 6, 12, 18, 24, 36, 60, and 72 months according to modified USPHS criteria. Statistical analysis included Pearson Chi-square, Friedman tests, Kaplan Meier, and Logistic Regression analysis (p < 0.05). After 72 months, 47 restorations in 19 patients were evaluated (55% follow-up rate). Seventy-five percent of the RBC (n = 26) and 74% (n = 21) of the RMGIC restorations were fully retained. There were no significant differences between materials regarding retention and marginal adaptation (p > 0.05). Cavity dimensions, caries activity, and retention exhibited no correlation (p > 0.05). The increase in marginal staining in both groups over time was significant (p < 0.001). RMGIC restorations exhibited higher discoloration than RBC restorations (p = 0.014). At 72 months, three secondary caries lesions were detected in both restoration groups: two RMGIC and one RBC. There were no reports of sensitivity. After 72 months, both RBC and RMGIC restorations were clinically successful, with similar retention and marginal adaptation scores. However, it is noteworthy that RMGIC restorations tend to discoloration over time compared to RBC. The trial is registered in the database of "Clinical Trials". The registration number is NCT0372-2758, October 29, 2018.

Long-term performance of ceramic in/-onlays vs. cast gold partial crowns - a retrospective clinical study

OBJECTIVES

To assess the long-term clinical performance of ceramic in-/onlays (CIOs) and cast gold partial crowns (CGPCs) in posterior teeth in terms of success, survival, complications (biological, technical) and quality.

MATERIAL AND METHODS

In a retrospective study, a total of 325 patients were recorded after up to 24.8 years (mean 13.9 ± 3.8 years) having (pre-)molars restored with CIO (Empress I, Ivoclar Vivadent, n = 161) and CGPC (Degunorm, DeguDent, n = 164) by supervised undergraduate students. A total of 296 restorations were assessed clinically and radiologically in healthy and endodontically treated teeth using modified United States Public Health Service (USPHS) criteria. Cumulative success and survival rates of the restorations were calculated using Kaplan-Meier estimates. Biological and technical complications were recorded. Status of oral health comprising caries risk and localized periodontitis were assessed.

RESULTS

The cumulative success rates of CIOs were 92.1% and of CGPCs 84.2% after mean service times of 14.5 years. The annual failure rates of total service times were 0.5% in teeth restored with CIO (n = 155) and 0.7% in teeth restored with CGPC (n = 163). The cumulative survival rates of CIOs were 93.9% after a mean service time of 15.2 years and decreased to 91.7% after 23.5 years. The cumulative survival rates of CGPCs were 92.6% after a mean service time of 14.9 years and 91.8% after 23.5 years. Complications in CIOs (n = 149) were ceramic fracture (6.7%), secondary caries (4.7%), endodontic complication (2.7%) and tooth fracture (1.3%) compared to CGPCs (n = 147) with endodontic complication (8.8%), secondary caries (4.8%) and decementation (2.0%). Endodontically treated teeth restored with CIO or CGPC revealed significantly less often success compared with corresponding vital teeth (p = .02). CIOs and CGPCs revealed clinically and radiographically good and excellent qualities with 71.8% (107/149) and 68% (100/147) without any significant differences regarding type of restoration.

CONCLUSIONS

Both CIOs and CGPCs achieved high survival rates up to 24.8 years when performed by supervised undergraduate students. The longevity of the restorations may benefit from the intraoral repair of accessible defects and, in case of pulp infection or necrosis, an adequate endodontic management.

CLINICAL RELEVANCE

CIOs and CGPCs made by supervised undergraduate students are proper restoration types in posterior teeth in the long-term. An adequate preparation design, meticulous care in the inserting technique and constant biofilm removal due to proper oral hygiene combined with professional maintenance care are substantial. The clinical long-term performance was mostly limited by ceramic fractures in CIOs and endodontic complications in CGPCs.

Clinical performance of two ion-releasing bulk-fill composites in class I and class II restorations: A two-year evaluation

OBJECTIVES

This randomized clinical trial evaluated and compared the 2-year clinical performance of two ion-releasing bulk-fill composites (Cention N and Surefil One) with that of a conventional bulk-fill resin composite (Powerfil) in Class I and II cavities.

METHODS

Thirty-two patients, each with 3 Class I and/or Class II cavities under occlusion, were enrolled in this trial. A total of 96 restorations were placed, 32 for each material, as follows: a self-adhesive composite; Surefil-one, alkasite; Cention N, and a bulk-fill resin composite; Powerfil. The restorations were placed by a single operator. Clinical evaluation was performed at baseline (1-week), 6-months, 1-year, and 2-years by two independent examiners using the FDI criteria. Intergroup and intragroup comparisons were analyzed using the Kruskal-Wallis and Friedman Tests. Multiple comparisons between groups were analyzed using the Mann-Whitney and Wilcoxon-rank tests. The level of significance was set at α = 0.05.

RESULTS

Twenty-seven patients with a total of 81 restorations were evaluated at the end of the 2-years with 84.35% recall rates. Clinical success rates were 100%, 100%, and 96.3% for Powerfil, Surefil-one, and Cention N, respectively. Cention N showed a statistically significant (p < 0.05) decreased marginal integrity in comparison with resin composite at the 2-year evaluation. No recurrent decay was detected in any restoration.

CONCLUSIONS

Both ion-releasing bulk-fill composites provided acceptable clinical performance similar to bulk-fill composite in Class I and II restorations over a 2-year period.

CLINICAL RELEVANCE

The results of this trial suggests that there is a promising evidence supporting the use of ion-releasing composites.

Factors influencing the longevity of posterior composite restorations: A dental university clinic study

Objectives

This retrospective study aimed to assess the performance of posterior composite resin restorations (PCRRs) and evaluate the influence of patient-specific factors on restoration outcomes.

Methods

A total of 189 PCRRs were examined in 54 patients, with evaluations based on Modified USPHS criteria. Patient-specific factors were analyzed. Statistical analyses, including chi-square tests, independent samples t-tests, and ANOVA tests, were conducted.

Results

Patients aged over 50 exhibited higher DMFT averages and a higher rate of unsuccessful restorations. Despite higher DMFT scores in females, gender doesn't significantly impact restoration outcomes. Secondary caries correlated with.plaque scores, significantly affecting restoration survival. Marginal adaptation, retention deficiencies, and secondary caries were primary causes of failure. Multi-surface restorations faced higher failure risk due to elevated plaque scores. Class-V restorations showed a higher failure rate, challenging the number of surfaces and longevity correlation.

Conclusions

This study identified key factors influencing posterior composite resin restorations-(PCRRs) in patients over 50, including higher DMFT averages and more unsuccessful restorations. No significant difference was found between brushing; frequency and DMFT rates, possibly due to the absence of non-brushers. Secondary caries; correlated with elevated plaque scores, impacting restoration survival. Primary causes of; failure included marginal adaptation issues, retention deficiencies, and secondary caries, with multi-surface restorations facing a higher risk. However, tooth vitality, beverage and acidic food consumption, and oral hygiene habits did not significantly affect PCRR outcomes.

Clinical significance

Patient-specific factors significantly impact PCRRs' long-term performance. Dentists must tailor strategies, emphasizing regular monitoring and preventive measures for extended survival.

Sixty-month comperative evaluation of a glass hybrid restorative and a composite resin in non-carious cervical lesions of bruxist individuals

OBJECTIVE

To compare the clinical performance of a glass hybrid (GH) restorative and a nano-ceramic composite resin (CR) in the restoration of non-carious cervical lesions (NCCLs) of bruxist individuals in a 60-month randomized clinical trial.

MATERIALS AND METHODS

Twenty-five bruxist candidates having NCCLs were recruited in this clinical study. The depth, height (cervico-incisal), width (mesio-distal), internal angles of the NCCLs, degree of tooth wear (TWI) and gingival index (GI) were measured. One hundred-and-forty-eight NCCLs were restored either with a GH restorative (Equia Forte Fil) or a CR (Ceram.X One Universal). Modified USPHS criteria was used to evaluate restorations after 1 week and 12, 24, 36 and 60 months. Pearson's Chi-Square, Fisher's Exact and Cochran Q tests were run for analysis. Survival rates of the restorations were compared with Kaplan-Meier analysis (p < 0.05).

RESULTS

After 60 months, 97 restorations in 15 patients were examined. The recall rate was 60.0%. Retention rates were 73.5% for CR and 66.7% for GH. A total of 29 restorations were lost (13CR (26.5%), 16GH (33.3%)). There was not a significant difference between tested restoratives in retention (p = 0.464), marginal adaptation (p = 0.856) and marginal discoloration (p = 0.273). There was no relationship between internal angle, depth, height or width and retention of the GH or CR restorations (p > 0.05). The increase in retention loss and marginal discoloration of both restorations over time were significant (p < 0.001). Sensitivity or secondary caries were not detected after 60 months.

CONCLUSION

GH and nano-ceramic CR showed similar clinical performances in NCCLs after 60 months in patients with bruxism.

CLINICAL SIGNIFICANCE

After 60 months, CR and GH materials showed clinically acceptable performances in restoration of NCCLs in patients with bruxism.

Influence of surface sealants on the quality of posterior restorations with bulk-fill composites: A 4-year randomized clinical trial

OBJECTIVES

The aim of this study was to evaluate the clinical performance of surface sealants associated with a bulk-fill composite in posterior restorations after 4 years.

METHODS

A total of 174 posterior restorations were performed on 57 participants using a self-etch adhesive system and a bulk-fill composite. The groups were then divided into the following categories: 1) without surface sealant (NoS), 2) with surface sealant Biscover (Bisco, SBi), and 3) with surface sealant Permaseal (Ultradent, SPe). Restorations were evaluated using FDI criteria at baseline and after 1 and 4 years. Statistical analysis was conducted using Kaplan-Meier survival analysis and the Chi-square test (α = 0.05).

RESULTS

After 4 years, only one restoration was lost (1 in the NoS group). The fracture/retention rate (with 95% confidence interval) was 98% for NoS and 100% for both SBi and SPe (p = 0.76). The majority of secondary outcomes showed minor defects, with no significant differences among the groups (p > 0.05). However, significant differences were observed among the groups in terms of marginal staining and marginal adaptation (p = 0.03). In both items, twelve restorations (nine in NoS, one in SBi, and two in SPe) showed minor marginal discrepancies favoring the sealant groups (SBi and SPe).

SIGNIFICANCE

Regardless of the use of surface sealants, the bulk-fill composite restorations showed excellent clinical performance after 4 years. However, the groups that received sealants showed better marginal adaptation and less marginal discoloration compared to those that did not receive sealants.

Survival analysis of posterior composite restorations in National Dental PBRN general dentistry practices

OBJECTIVE

Quantify the survival of posterior composite restorations (PCR) placed during the study period in permanent teeth in United States (US) general dental community practices and factors predictive of that survival.

METHODS

A retrospective cohort study was conducted utilizing de-identified electronic dental record (EDR) data of patients who received a PCR in 99 general dentistry practices in the National Dental Practice-Based Research Network (Network). The final analyzed data set included 700,885 PCRs from 200,988 patients. Descriptive statistics and Kaplan Meier (product limit) estimator were performed to estimate the survival rate (defined as the PCR not receiving any subsequent treatment) after the first PCR was observed in the EDR during the study time. The Cox proportional hazards model was done to account for patient- and tooth-specific covariates.

RESULTS

The overall median survival time was 13.3 years. The annual failure rates were 4.5-5.8 % for years 1-5; 5.3-5.7 %, 4.9-5.5 %, and 3.3-5.2 % for years 6-10, 11-15, and 16-20, respectively. The failure descriptions recorded for < 7 % failures were mostly caries (54 %) and broken or fractured tooth/restorations (23 %). The following variables significantly predicted PCR survival: number of surfaces that comprised the PCR; having at least one interproximal surface; tooth type; type of prior treatment received on the tooth; Network region; patient age and sex. Based on the magnitude of the multivariable estimates, no single factor predominated.

CONCLUSIONS

This study of Network practices geographically distributed across the US observed PCR survival rates and predictive factors comparable to studies done in academic settings and outside the US.

CLINICAL SIGNIFICANCE

Specific baseline factors significantly predict the survival of PCRs done in US community dental practices.

To etch or not to etch, Part III: On the hydrophobic-rich content and fatigue strength of universal adhesives after long-term ageing

OBJECTIVES

To examine whether dentin-etching extension and/or the hydrophobic-rich content of hybrid layers would affect fatigue strengths of a mild universal adhesive after long-term aging.

METHODS

Twin-bonded resin-dentin interfaces were produced by etching sound midcoronal dentin beams with 32 % ortho-phosphoric acid for 15 s (OPA15s), 3 s (OPA3s) or 10 % meta-phosphoric acid for 15 s (MPA15s). Samples were bonded with a mild universal adhesive with or without additional coating using a solvent-free bisGMA-based bonding resin. Self-etch application served as control. Composite buildups were made with a nanofilled composite. Bar-shaped twin-bonded interfaces (0.9 × 0.9 × 12 mm) were aged for two years in artificial saliva at 37 ℃ and tested under 4-point flexure at quasi-static (n = 16) and cyclic loads (n = 35) until failure. The stress-life fatigue behavior was evaluated using the staircase method at 4 Hz. Crack initiation and fracture patterns were evaluated by SEM. Cyclic-loaded data was analyzed by Kruskal-Wallis on Ranks (α = 0.05).

RESULTS

Significantly higher fatigue life distributions and higher endurance limits were observed for less aggressive etch-and-rinse protocols (OPA3s and MPA15s) after long-term ageing. Hydrophobic-rich coating produced 20-32 % higher endurance limits, prevented micrometer-sized porosities at bonded interfaces, reduced etching-associated variability and lowered crack formation. Significance Long-term hydrolysis produces detrimental effects on the fatigue strength of resin-dentin interfaces. The bond-promotion effect of less aggressive etch-and-rinse protocols and the creation of hybrid layers with higher hydrophobic-rich content are critical to extend the durability of mild universal adhesives. Therefore, current oversimplification trends in adhesive dentistry may limit resin-dentin bonding performance.

Effect of resin composite shade on digital fiber-optic transillumination imaging in vitro

Digital imaging fiber-optic transillumination (DIFOTI) devices have been used to detect caries, a technique without using X-rays. However, the effects of resin composites (RCs) shades on the images acquired with DIFOTI devices have not been investigated. Thus, this study aimed to elucidate the influence of RC shade on the images obtained with DIFOTI technique. Three shades (A1, A3, and Opaque) for each of four flowable RCs were filled on a cavity prepared in a left mandibular first premolar obtained from a donated body. Then, transmission images with a DIFOTI device (DIAGNOcam; KaVo, Biberach, Germany) were acquired, and the average lightness values of the images in the RC and enamel were used to calculate differences between those areas. To clarify the influence of the optical translucency and color on DIFOTI images, the color parameters (L*, a* and b*) of each RC were obtained with black and white backgrounds. The color differences between the backgrounds were calculated as transparency parameter (TP) values. The number of repetitions was set to 10. Differences in the lightness value of the shades varied in each RC. The difference in lightness was significantly associated with the TP value and color parameters of L* (p < 0.01), with negative (R = - 0.81) and positive (R = 0.84) correlations, respectively. In conclusion, DIFOTI images of RCs with high optical translucency resembled those of the natural tooth structure.

Long term clinical performance of 'open sandwich' and 'total-etch' Class II composite resin restorations showing proximal deterioration of glass-ionomer cement

OBJECTIVES

To compare clinical performance of resin composite posterior Class-II restorations placed with etch-and-rinse adhesive or open sandwich technique using glass-ionomer cement.

METHODS

Data on Class II restorations placed by one dentist between 1990 and 2016 were collected from patient files, including caries risk, tooth related variables, applied materials and dates of last check-up visit and restoration placement. Open sandwich restorations were placed before 2001, while after 2001, a total-etch technique using etch-and-rinse 3-step adhesive was used when placing a Class II composite restoration. For statistical analysis, Kaplan-Meier statistics and a multilevel Cox-Regression was conducted (p < 0.05). Annual Failures Rates (AFR) were calculated.

RESULTS

675 Class II restorations were placed in 91 patients, 491 total-etch restorations (observation time 2-18 y), and 184 open sandwich restorations (observation time 19-29 y) showing AFRs at 15 years as 2.9 % for total-etch and 9.7 % for open sandwich restorations. Secondary caries as failure was equally distributed among the 2 groups and 27 % of the failures in the open sandwich group were due to proximal deterioration of glass-ionomer cement. The Cox-regression showed a significant higher risk for failure for the open sandwich technique compared to total-etch class-II composite restorations (HR = 2.9; p < 0.001).

SIGNIFICANCE

Application of glass-ionomer cement using the open sandwich technique cannot be recommended for class-II restorations as being more complex and showing poorer clinical performance.

Study on the Restoration of Class II Carious Cavities by Virtual Methods: Simulation of Mechanical Behavior

The restoration of class II cavities is predominantly carried out with composite materials. Due to the high failure rate in restoring this type of cavity, composite materials with much-improved properties and new application techniques have been promoted. The study aimed to analyze the mechanical behavior of several topical composite materials (nanocomposites, nanohybrids and ormocer) using different application techniques. In a lower second molar, a class II occlusal cavity was prepared. As filling materials, we used the following combinations: Admira Fusion and Admira Fusion Flow, Grandio and Grandio Flow, Filtek Supreme XT and Filtek Supreme Flow. These were applied using a snow plow, injection molded and Bichacho techniques. Three-dimensional scanning of the molar with the prepared cavity was performed, and then scanning of each layer of added composite material was performed, obtaining three-dimensional models. The virtual molar models were analyzed with software specific to the finite element analysis method, where their physical-mechanical properties were entered and assigned to the components of the virtual molar. Simulations at high forces specific to bruxism were then carried out and analyzed, and compared. The values of displacements and strain, for all six analyzed situations, are relatively small (range from 5.25 × 10^-6-3.21 × 10^-5 for displacement, 6.22 × 10^-3-4.34 × 10^-3 for strain), which validates all three methods and the materials used. As far as the stress values are concerned, they are similar for all methods (250-300 MPa), except for the snow plow and injection-molded techniques using Grandio and Grandio Flow composites, where the maximum von Mises stress value was more than double (approximately 700 MPa). When using the combination of Grandio and Grandio Flow materials, the 1 mm thickness of the fluid composite layer was found to have a major influence on occlusal forces damping as opposed to 0.5 mm. Therefore, the Bichacho technique is indicated at the expense of the snow plow and injection-molded techniques. The composite materials used by us in this study are state-of-the-art, with clear indications for restoring cavities resulting from the treatment of carious lesions. However, their association and application technique in the case of Class II cavities is of clinical importance for resistance to masticatory forces.

Five-Year Clinical Performance of Complex Class II Resin Composite and Amalgam Restorations-A Retrospective Study

The aim of this retrospective study was to investigate the clinical performance of posterior complex resin composite (RC) and amalgam (AM) restorations after a five-year period. One hundred and nineteen complex Class II restorations placed by dental students were evaluated using the USPHS criteria. Data were analyzed using Chi-square, Mann-Whitney, and Wilcoxon tests at a 0.05 level of significance. After five years, the percentages of clinically satisfactory complex Class II RC and AM restorations were 78% and 76.8%, respectively. The main reasons for the failure of AM restorations included secondary caries (Bravo-10.1%), defective marginal adaptation (Charlie-8.7%), and fracture of the tooth (Bravo-7.2%). RC restorations presented failures related to the fracture of the restoration (Bravo-16%) and defective marginal adaptation (Charlie-8.2%). There was a significantly higher incidence of secondary caries for AM restorations (AM-10.1%; RC-0%; p = 0.0415) and a higher number of fractures for RC restorations (AM-4.3%; RC-16%; p = 0.05). Regarding anatomy, AM restorations presented a significantly higher number of Alfa scores (49.3%) compared to RC restorations (22.4%) (p = 0.0005). The results of the current study indicate that complex class II RC and AM restorations show a similar five year clinical performance.

Fracture Load of Mesio-Occluso-Distal Composite Restorations Performed with Different Reinforcement Techniques: An In Vitro Study

BACKGROUND

Mesio-occluso-distal (MOD) cavity preparations are often fragile due to the amount of tooth and carious structure removed. MOD cavities can often fracture if left unsupported.

AIM

The study investigated the maximum fracture load of mesi-occluso-distal cavities restored using direct composite resin restorations with various reinforcement techniques.

METHOD

Seventy-two freshly extracted, intact human posterior teeth were disinfected, checked, and prepared according to predetermined standards for mesio-occluso-distal cavity design (MOD). The teeth were assigned randomly into six groups. The first group was the control group restored conventionally with a nanohybrid composite resin (Group I). The other five groups were restored with a nanohybrid composite resin reinforced with different techniques: the ACTIVA BioACTIVE-Restorative and -Liner as a dentin substitute and layered with a nanohybrid composite (Group II); the everX Posterior composite resin layered with a nanohybrid composite (Group III); polyethylene fibers called "Ribbond" placed on both axial walls and the floor of the cavity, and layered with a nanohybrid composite (Group IV); polyethylene fibers placed on both axial walls and the floor of the cavity, and layered with the ACTIVA BioACTIVE-Restorative and -Liner as a dentin substitute and nanohybrid composite (Group V); and polyethylene fibers placed on both axial walls and the floor of the cavity and layered with the everX posterior composite resin and nanohybrid composite (Group VI). All teeth were subjected to thermocycling to simulate the oral environment. The maximum load was measured using a universal testing machine.

RESULTS

The highest maximum load was exhibited by Group III with the everX posterior composite resin, followed by Group IV, Group VI, Group I, Group II, and Group V. A statistically significant difference was demonstrated between groups (p = 0.0023). When adjusting for multiple comparisons, there were statistical differences specific to comparisons between Group III versus I, Group III versus II, Group IV versus II, and Group V versus III.

CONCLUSIONS

Within the limitations of the current study, it can be concluded that a higher maximum load resistance can be achieved (statistically significant) when reinforcing nanohybrid composite resin MOD restorations with everX Posterior.

A 23-Year Observational Follow-Up Clinical Evaluation of Direct Posterior Composite Restorations

The purpose of this observational follow-up clinical study was to observe the quality of posterior composite restorations more than 23 years after application. A total of 22 patients, 13 male and 9 female (mean age 66.1 years, range 50–84), with a total of 42 restorations attended the first and second follow-up examinations. The restorations were examined by one operator using modified FDI criteria. Statistical analysis was performed with the Wilcoxon Mann–Whitney U test and Wilcoxon exact matched-pairs test with a significance level of p = 0.05. Bonferroni–Holm with an adjusted significance level of alpha = 0.05 was applied. With the exception of approximal anatomical form, significantly worse scores were seen for six out of seven criteria at the second follow-up evaluation. There was no significant difference in the first and second follow-up evaluations in the grades of the restorations with regard to having been placed in the maxilla or mandible, as well as for one-surface or multiple-surface restorations. The approximal anatomical form showed significantly worse grades at the second follow-up when having been placed in molars. In conclusion, the study results show that significant differences regarding FDI criteria in posterior composite restorations occur after more than 23 years of service. Further studies with extended follow-up time and at regular and short time intervals are recommended.

Clinical longevity of extensive direct resin composite restorations after amalgam replacement with a mean follow-up of 15 years

OBJECTIVES

The aim of this retrospective clinical study was to determine the survival of extensive direct resin composite restorations after amalgam replacement on vital molars and premolars after a mean observation period of 15 years.

METHODS

Between January 2007 and September 2013, a total of 117 extensive cusp replacing direct resin composite restorations were placed in 88 patients in a general dental practice. These were indicated for replacement of existing amalgam restorations. Tooth vitality, the absence of at least one cusp in premolars, and at least two cusps in molars were considered for inclusion. The long-term follow-up of the restorations, re-evaluated after up to 17 years using the original evaluation criteria is reported.

RESULTS

81 of 88 patients (92.1%) and 106 of 117 restorations (90.6%) were available for follow-up. The cumulative success rate was 62.0% (95% CI: 47.3-76.2, AFR 2.79%) after a mean observation time of 163.4 months, the cumulative survival rate was 74.7% (95% CI: 59.8-89.6%, AFR: 1.70%) after a mean observation time of 179.1 months. The number of cusps replaced in premolars had a statistically significant influence on the success and survival rate of the restorations (HR of respectively, 2.974 and 3.175, p = <0.0005). Premolars with two cusps replaced had 297% more chance of failure than premolars with one cusp replaced.

CONCLUSIONS

Extensive direct resin composite restorations placed after amalgam replacement showed good survival after a mean observation period of 15 years. The number of cusps involved had a statistically significant influence on the longevity of the restorations in premolars.

CLINICAL SIGNIFICANCE

With good survival and low annual failure rates, direct resin composite restorations are a suitable treatment for repairing extensive defects in posterior teeth involving multiple cusps and surfaces, provided that they are placed by a dentist who has long experience and is skilled in the placement of direct composite materials.

Can composite packaging and selective enamel etching affect the clinical behavior of bulk-fill composite resin in posterior restorations? 24-month results of a randomized clinical trial

OBJECTIVES

This is a double-blind, split-mouth, randomized clinical study that aims to evaluate the influence of bulk-fill composite packaging presented in syringes (BSy) and capsules (BCa), and the effect of selective enamel etching (SEE) on the clinical performance of class I and II bulk-fill resin composite restorations after 24 months.

METHODOLOGY

A total of 295 class I or class II restorations were performed on 70 patients. One universal adhesive was applied in all restorations. SEE was used in 148 restorations and self-etching mode (SET) in 147 restorations. After the adhesive application, cavities were restored with Filtek Bulk-fill Posterior Restorative in syringes (BSy), Filtek One Bulk-fill in capsules (BCa), or Filtek Supreme Ultra in syringes with the incremental technique (In). All restorations were evaluated using the FDI criteria after one week and after six, 12, and 24 months. Kaplan-Meier survival analysis and Pearson's Chi-square test were used (α=0.05) for statistical analysis.

RESULTS

After 24 months, 62 patients were evaluated and four restorations were lost due to fracture (one for SEEBSy, two for SEEIn, and one for SETIn). No significant differences in the fracture and retention rate were found between groups (p>0.05). SEE showed significantly fewer marginal adaptation defects than SET (p<0.05). BCa and BSy groups showed fewer marginal discrepancies compared to In (p<0.05). Restorations performed with BCa showed less color mismatch than BSy or In (p<0.05).

CONCLUSION

Although all restorations exhibited satisfactory clinical performance after 24 months of clinical service, the clinical behavior of class I and II restorations' improved when performed with a bulk-fill composite in capsules, mainly when associated with a universal adhesive applied with SEE.

Longevity of composite restorations is definitely not only about materials

OBJECTIVES

This review study provides an overview of factors that influence the longevity of all types of direct resin composite restorations.

METHODS

A systematic search was performed in PubMed, Scopus, and Web of Science databases for articles reporting data from primary longitudinal clinical studies on composite longevity published 2011-2021. Prospective or retrospective studies with restorations in permanent dentition, with follow-up periods of at least 5 years were included.

RESULTS

In total, 33 articles were included with different study designs, practice settings, datasets, countries of origin, and sample sizes. Annual failure rates of restorations ranged from 0.08% to 6.3%. Survival rates varied between 23% and 97.7%, success rates varied between 43.4% and 98.7%. Secondary caries, fractures, and esthetic compromise were main reasons for failures. Risk factors for reduced restoration durability included patient-level factors (e.g., caries risk, parafunctional habits, number of check-ups per year, socioeconomic status), dentist factors (different operators, operator's experience), and tooth/restoration factors (endodontic treatment, type of tooth, number of restored surfaces). Patient gender and the composite used generally did not influence durability.

SIGNIFICANCE

A number of risk factors are involved in the longevity of composite restorations. Differences between composites play a minor role in durability, assuming that materials and techniques are properly applied by dentists. Patient factors play a major role in longevity. The decision-making process implemented by dentists relative to the diagnosis of aging or failed restorations may also affect the longevity of restorations. Clinicians should treat patients comprehensively and promote a healthy lifestyle to ensure longevity.

Effect of thickness on the degree of conversion of two bulk-fill and one conventional posterior resin-based composites at high irradiance and high temporal resolution

OBJECTIVES

This study: 1) measures the effect of sample thickness and high irradiance on the depth-dependent time delay before photopolymerization reaction onset; 2) determines if exposure reciprocity exists; 3) measures the conversion rate at four irradiance levels; 4) determines the time, t0, at which the maximum DC rate is reached for two bulk-fill and one conventional posterior resin-based composites (RBCs).

METHODS

Tetric PowerFill IVA shade (Ivoclar Vivadent) and Aura bulk-fill ultra universal restorative (SDI), and one conventional posterior resin-based composite (RBC), Heliomolar A3 (Ivoclar Vivadent), that were either 0.2 mm, 2 mm, or 4 mm thick were photocured using a modified Bluephase G4 (Ivoclar Vivadent) light-curing unit (LCU) that delivered a single emission band (wavelength centered at 449 nm). The same radiant exposure of 24 J/cm2 was delivered at irradiances ranging from 0.5 to 3 W/cm2 by adjusting the exposure time. PowerFill was also photocured for 3 s or 6 s using a Bluephase PowerCure LCU (Ivoclar Vivadent) on the 3 s mode setting. The degree of conversion (DC) was measured in real-time at a high temporal resolution at 30 °C using Attenuated Total Reflection (ATR) FTIR spectroscopy with a sampling rate of 13 DC data points per second. The DC data were analyzed using a phenomenological autocatalytic model. The RBC viscosity was measured at 21 °C and 30 °C. Light transmission through the RBC samples at 22 °C was monitored with time to calculate the extinction coefficients of the RBCs.

RESULTS

The time delay before photopolymerization started increased as the RBC thickness increased and the irradiance decreased. An autocatalytic model described the DC data. The time t0 was less than 77 ms for the 0.2 mm thick samples of PowerFill irradiated using the highest irradiance of 3 W/cm2. Among the three RBCs for each sample thickness and irradiance level, the PowerFill had the smallest time t0. There was a time delay of 0.59 s and 1.25 s before the DC started to increase at the bottom of 4 mm thick samples for the PowerFill and Aura, respectively, when an irradiance of 1 W/cm2 was delivered. The time delay increased to 3.65 s for the Aura when an irradiance of 0.5 W/cm2 was delivered. The extinction coefficients near 449 nm were 0.78 mm-1, 0.76 mm-1, and 1.55 mm-1 during the first 2 s after the start of photocuring of PowerFill, Aura, and Heliomolar, respectively. Only PowerFill followed exposure reciprocity. At T = 30 °C, the viscosity was 3400, 17000, and 5200 Paˑs for PowerFill, Aura, and Heliomolar, respectively.

SIGNIFICANCE

The time delay between when photopolymerization starts at the top and bottom of 2- or 4-mm thick RBC restorations may affect the structural integrity of the bond between the tooth and the bottom of the restoration. Only PowerFill followed exposure reciprocity between irradiance levels of 0.5 to 3 W/cm2. Exposure reciprocity did not occur for Aura or Heliomolar, neither of which are optimized for short light exposure or high irradiance conditions.

Resin Composites in Posterior Teeth: Clinical Performance and Direct Restorative Techniques

Resin composites are the most versatile restorative materials used in dentistry and the first choice for restoring posterior teeth. This article reviews aspects that influence the clinical performance of composite restorations and addresses clinically relevant issues regarding different direct techniques for restoring posterior teeth that could be performed in varied clinical situations. The article discusses the results of long-term clinical trials with resin composites and the materials available in the market for posterior restorations. The importance of photoactivation is presented, including aspects concerning the improvement of the efficiency of light-curing procedures. With regard to the restorative techniques, the article addresses key elements and occlusion levels for restoring Class I and Class II cavities, in addition to restorative strategies using different shades/opacities of resin composites in incremental techniques, restorations using bulk-fill composites, and shade-matching composites.

Randomized clinical split-mouth study on a novel self-adhesive bulk-fill restorative vs. a conventional bulk-fill composite for restoration of class II cavities - results after three years

OBJECTIVES

This randomized prospective split-mouth study evaluated the clinical performance of a novel, tooth-colored, self-adhesive bulk-fill restorative (SABF, 3M) for restoration of class II cavities as compared to a conventional bulk-fill composite (Filtek One, 3M; FOBF) over 36 months. The null-hypothesis was that both materials perform equally regarding clinical success and performance according to the FDI clinical criteria and scoring system.

METHODS

30 patients received one SABF and one FOBF restoration each. For FOBF, Scotchbond Universal (3M) was used as adhesive (self-etch mode), whereas SABF was applied without adhesive. Two blinded examiners evaluated the restorations at baseline, 24 and 36 months using FDI criteria. Data were analyzed non-parametrically (χ²-tests; α=0.05).

RESULTS

29 patients were available for the 24- and 36-month examinations. Clinical success rate was 96.6% for both materials at 36-mo (one restoration failure due to secondary caries each). All other restorations revealed clinically acceptable FDI scores at all recalls. FOBF performed significantly better than SABF at all time points regarding surface lustre (p<0.001) and color match and translucency (p<0.001) and regarding marginal staining at 36-months (p=0.008). Marginal staining and marginal adaptation deteriorated significantly over time for both materials (both p<0.001).

CONCLUSIONS

The null-hypothesis could only partially be rejected. Both materials performed similarly regarding clinical success and performance within 36 months of clinical service, but SABF exhibited significantly inferior, but clinically fully acceptable esthetic properties as compared to FOBF. Both restorative materials showed clinically fully acceptable results over 36 months of clinical service and thus may be recommended for clinical use.

CLINICAL SIGNIFICANCE

The novel tooth-colored self-adhesive bulk-fill restorative exhibited clinically fully acceptable results over 36 months of clinical service, similarly to a conventional bulk-fill restorative used with a universal adhesive, but with slight shortcomings in esthetic properties. Therefore, both restorative materials may be recommended for clinical use.

Marginal integrity of classical and bulk-fill composite restorations in permanent and primary molars

Bulk-fill composites enable timesaving and less technical-sensitive application of restorations. This study investigated and compared the marginal integrity of classical and bulk-fill composite restorations in primary and permanent molars before and after thermo-mechanical loading (TML). Two Class II cavities were prepared in each of 20 primary and 20 permanent molars. The molars were randomised in four groups for each molar type. Groups 1 and 5 were restored with a high-viscous bulk-fill composite (Tetric PowerFill), groups 2 and 6 were restored with a flowable bulk-fill composite (Tetric PowerFlow), groups 3 and 7 were restored with a high-viscous classical composite (Tetric Prime), and groups 4 and 8 were restored with a flowable classical composite (Tetric EvoFlow). In permanent molars, the flowable composites were covered with a 2-mm layer of high-viscous composite (groups 6 and 8). The restorations were subjected to TML in a custom-made chewing machine (5-50 °C, 2 min dwelling time, × 1000; 400 ,000 loading cycles, 1.7 Hz, 49 N), and quantitative marginal analysis was conducted using scanning electron microscopy. Marginal integrity of each restoration was calculated as a percentage of continuous margins before and after TML. The tested high-viscous bulk-fill restoration showed similarly high marginal integrity in primary and permanent molars as the classical restoration. The tested flowable bulk-fill restoration showed the lowest marginal integrity compared to all other restorations after TML. In contrast to flowable bulk-fill restorations, high-viscous bulk-fill restorations show similar marginal integrity as classical hybrid composite restorations after TML, in both primary and permanent molars.

Additional information of bitewings to first time clinical examination of caries and restoration status in permanent dentition

OBJECTIVES

Identifying additional information obtained by X-rays combined with clinical examination concerning primary caries, caries adjacent to restorations and quality of restorations.

MATERIAL AND METHODS

A total of 240 adult patients, equally distributed in gender and six age-groups, were randomly selected from an original study population of 4,402 subjects (DANHES). Clinical and radiographical registrations on occlusal and approximal surfaces in posterior teeth were categorized into unrestored surfaces (sound/primary caries) and restored surfaces (without/with caries adjacent to restorations). Material and quality of restorations were also recorded. Chi-square and Fisher-exact tests were used for statistical analyses.

RESULTS

Of potentially 11,520 surfaces, 3,015 occlusal and 5,112 approximal surfaces were analysed. Occlusal: Of 907 unrestored surfaces, 110 had primary caries and 53% were detected radiographically. A total of 183 of 2,108 restored surfaces had caries adjacent to restorations, and 99% were found radiographically. A total of 190 restorations were over/under-extended, and 89% were registered radiographically. Approximal: Of 2,649 unrestored surfaces 648 had primary caries, and 92% were registered radiographically. A total of 565 of 2,463 restored surfaces had caries adjacent to restorations, and 99% were found radiographically. A total of 638 restorations were over/under-extended, and 98% were found radiographically. For all restorations, material and depth influenced quality of restorations and incidence of caries adjacent to restorations. At least one independent variable (gender/age group/tooth-type/jaw/side/mesial-distal surface) influenced frequencies of primary caries, caries adjacent to restorations and quality of restorations.

CONCLUSIONS

First-time clinical examination must be supplemented with X-rays to obtain a complete impression of caries status in posterior regions regarding diagnostics of caries, assessment of lesion depth and quality of restorations.

One-year clinical results of restorations using a novel self-adhesive resin-based bulk-fill restorative

This prospective study assessed the dual-curing self-adhesive bulk-fill restorative Surefil one. The restorations were placed and reviewed by dental practitioners who are members of a practice-based research network in the United States. Seven practitioners filled 60 cavities (20 class I, 19 class II and 21 class V) in 41 patients with Surefil one without adhesive, according to the manufacturer’s instructions. The restorations were evaluated using modified USPHS criteria at baseline, 3 months, and 1 year. Patients were also contacted to report postoperative hypersensitivity one to four weeks after placement. The only patient that showed moderate hypersensitivity after 1 year had previously reported symptoms that were unlikely associated to the class I molar restoration. One class II restoration in a fractured maxillary molar was partially lost. The remaining restorations were found to be in clinically acceptable condition resulting in an annual failure rate of 2%. Color match showed the lowest number of acceptable scores (88%) revealing significant changes over time (P = 0.0002). No significant differences were found for the other criteria (P > 0.05). The novel self-adhesive bulk-fill restorative showed clinically acceptable results in stress-bearing class I and II as well as non-retentive class V cavities at 1-year recall.

Preparation of Ca doped wrinkled porous silica (Ca-WPS) for the improvement of apatite formation and mechanical properties of dental resins

The purpose of this work was to fabricate and characterize Ca doped wrinkled porous silica (Ca-WPS), and evaluate their effect on the mineralization and mechanical properties of resin composites as functional fillers. Ca-WPS were prepared by sol-gel method and characterized by scanning electron microscopy, transmission electron microscopy and N₂ adsorption-desorption measurements. The mineralization properties of the prepared Ca-WPS particles and the resin composites with different amount of Ca-WPS were evaluated by simulated body fluid (SBF) immersion method. The mechanical properties (flexural strength, flexural modulus, compressive strength and microhardness) of the dental resins containing unimodal Ca-WPS fillers and bimodal Ca-WPS fillers with nonporous silica were evaluated by a universal testing machine. Results showed that after immersing in SBF for 5 d, apatite formed on the surface of Ca-WPS and composites containing Ca-WPS fillers, indicating the excellent mineralization property of the prepared Ca-WPS. The mechanical properties of the dental resins increase with the increase of the proportion of unimodal Ca-WPS fillers. The dental resins with bimodal Ca-WPS fillers showed better mechanical properties than the group with only nonporous fillers at the same filler loading (60 wt%). Among all the samples, the dental composites filled with bimodal fillers (mass ratio of Ca-WPS: nonporous silica = 10:50, total filler loading 60 wt%) exhibited the best mechanical performance. The flexural strength, flexural modulus, compressive strength and microhardness of these samples were 26.96%, 42.75%, 16.04% and 54.1% higher than the composites with solid silica particles alone, respectively. Thus, the prepared Ca-WPS could effectively improve the apatite formation and mechanical properties of resin composites.

Implementation in restorative treatments in public health: a 10-year analysis of resin composite procurement in Brazil

This study aims to assess the resin composite purchases in a public health system and understand the variables associated with its cost and with the decision-making process over a period of 10 years. Secondary data collection was performed using the Brazilian Healthcare Prices Database (BDHP) from 2010 to 2019. All conventional and bulk-fill composites were selected. Date of purchase, institution type and location, procurement modality, number of purchased items, manufacture, and unit prices were collected. A multiple linear regression model assessed the influence of price in the procurement variables, while a multinomial logistic regression compared purchase probabilities between the materials. In total, 18,138 observations were collected with 2,129,294 purchased units and a total cost of USD 43,504,260.00. Conventional composites appeared in 98.5% of the procurement process. Nanofilled conventional composites were the most purchased materials, with an increased probability of purchase over time, despite its higher prices. An increase in prices was predicted for bulk-fill materials when compared to conventional ones. The odds of purchasing this category increased by 3.14x for every price increase over the years. Sociodemographic and type of institution influences the prices and the probability of procurement in the healthcare system. Nanofilled and bulk-fill resin are increasingly included in clinical practice. These findings highlight possible modifications to the standard-of-care in restorative treatments and how the translation of knowledge may occur from the development of new materials to the clinical application considering the economic impact of these modifications.

[Laboratory methods for measuring adhesive bond strength between restoration materials and hard tooth tissues]

THE AIM OF THE STUDY

Was to review laboratory methods measuring the bond strength of adhesive dental materials to hard tooth tissues. The paper points out the impact of test conditions on the measured strength of adhesive bond to dentine and enamel. Various in vitro studies are discussed, including the analyses of fracture surfaces and test-induced stresses. These studies are found to be helpful to identify particularities, advantages, and limitations of each approach. We present a systematic picture of available bond-strength data aimed at revealing general trends in adhesive performance. No clear superiority of any particular method for determining the bond strength between restoration materials and tooth tissues can be identified on the basis of reviewed literature. Therefore, no single universal approach can be at present proposed for determining the strength of adhesive bond.

In vitro evaluation of marginal adaptation in medium- and large size direct class II restorations using a bulk-fill or layering technique

OBJECTIVES

to test if cavity dimensions and restorative protocol have potential to influence in-vitro adaptation of class II restoration after simulated thermo-occlusal stressing.

METHODS

A total of 32 prepared teeth were randomly assigned to one of the 4 experimental groups depending on cavity size, composite system and filling technique; group 1: small cavity and multi-layered conventional restorative composite (Tetric Evo-ceram: TEC), group 2: small cavity and flowable bulk-filled composite (SDRFlow: SDR) + one single occlusal layer of conventional restorative composite (TEC), group 3: large cavity and multilayered conventional restorative composite (TEC) and group 4: large cavity and bulk-filled flowable composite (SDR) + one single occlusal layer conventional restorative composite (TEC). All specimens were submitted to 500'000 cycles of thermomechanical loading (50 N, 5 to 55 °C). The proximal tooth-restoration interface was analyzed quantitatively by SEM, prior and after thermomechanical loading.

RESULTS

Before loading, continuous enamel adaptation varied from 61.49% (Gr 1) to 68.39% (Gr 4) proximally and from 50.93% (Gr2) to 68.65% (Gr1) cervically, with no statistical difference among groups for both segments. After thermomechanical loading, continuous enamel adaptation varied from 36.6% (Gr2) to 46.6% (Gr1) proximally, without significant difference, and from 20.2% (Gr4) to 51.3% (Gr1) cervically; statistical differences in cervical enamel adaptation were found in-between groups 1 and 2 (p = 0.0479), 1 and 4 (P = 0.0116), 2 and 3 (p = 0.0028) and 3 and 4 (p = 0.001). Before loading, dentin continuous adaptation varied from 55.32% (Gr3) to 81.82% (Gr4) with statistical difference in-between those groups (p = 0.045); after loading, dentin continuous adaptation varied from 31.56% (gr2) to 51% (Gr4) with a statistical difference between those 2 groups (p = 0.019). The drop in adaptations values after loading was significant in all groups and segments.

CONCLUSIONS

The impact of the restorative technique and cavity size on marginal adaptation appeared essentially after simulated fatigue for enamel adaptation. Cervical enamel and dentin continuous adaption of small and large bulk-filled restorations dropped significantly while the change was lower in layered restorations made of conventional restorative composite.

CLINICAL SIGNIFICANCE

Restorations made with bulk-filled flowable composite behaved differently from layered ones using conventional resin composite, according to cavity size and loading.

Real-Time Feedback of the Applied Light-Curing Technique and Its Impact on Degree of Conversion of Composite Restorations-A Study with Undergraduate Dental Students

The objective of this study was to investigate the effect of individual instructions and training of dental students on the amount of applied light irradiance before and after training using a patient simulator with integrated visual feedback. Furthermore, the effect on the degree of conversion of composite restorations placed by the dental students was assessed. Forty-two dental students, split into two groups, light-cured a simulated restoration in tooth 27 of a dental patient simulator for 20 s. The irradiance (mW/cm²) received by the detector was measured in real-time before and after individual instructions and training, and the energy delivered (J/cm²) was calculated for each student. The degree of conversion at the bottom of incrementally placed composite restorations prior to individual instructions (group 1) and after individual instructions (group 2) was assessed using Fourier-transform infrared (FTIR) spectroscopy. The irradiance and degree of conversion measurements were re-assessed after all students received individual instructions. Data were analyzed using Wilcoxon signed-rank test and Mann-Whitney U-test at an overall level of significance of α = 0.05. A significant increase (p < 0.001) in applied light irradiance could be observed after individual instructions for both groups, with notably reduced data scattering. However, no significant difference was detected for the degree of conversion of placed composite restorations before or after instruction and training. Neither gender nor age of the dental students affected the obtained results. Consistent light energy delivered by dental students could be achieved through individual instructions and training with a patient simulator, also leading to less scattered irradiance results. However, the improved light-curing performance after the training did not affect the degree of conversion of the placed class II composite restorations.

Compliance of randomized controlled trials in posterior restorations with the CONSORT statement: a systematic review of methodology

OBJECTIVES

This study aims to investigate the compliance of randomized controlled trials (RCTs) in posterior restorations with the Consolidated Standards of Reporting Trials Statement (CONSORT) statement and to analyze the risk of bias (RoB) of these studies.

METHODS

A systematic search was performed in PubMed, Scopus, Web of Science, LILACS/BBO, and Cochrane Library. Only RCTs published in peer-reviewed journals were included. The compliance with the CONSORT was evaluated in a 0-2 scale where 0 = no description, 1 = poor description and 2 = adequate description. Descriptive analyses of the CONSORT mean score by journal, country, and RoB were performed. The RoB in RCTs was evaluated by using the Cochrane Collaboration's tool version 1.0.

RESULTS

A total of 15,476 studies were identified after duplicates removal. O only 202 meet the eligibility criteria, among which 31 were follow-up studies. Concerning the overall RoB, only 29 out of 171 were classified as low risk of bias. The overall mean CONSORT score was 19 ± 5.4 points, which means compliance of approximately 59%. Significant differences among countries, publication period, and RoB were observed (p < 0.001). The journal's impact factor was not correlated with the overall CONSORT score (p = 0.36).

CONCLUSIONS

The adherence of RCTs conducted in posterior restorations to the CONSORT Statement is still low. In addition, most studies were classified as at unclear risk of bias. These results call up an urgent need for improvement.

CLINICAL RELEVANCE

Most RCTs conducted in posterior teeth have poor reporting and are mainly classified as having an unclear risk of bias.

Polymerization Shrinkage of Short Fiber Reinforced Dental Composite Using a Confocal Laser Analysis

The purpose of this study was to investigate the polymerization shrinkage of short fiber reinforced composite (SFRC) using a multicolor confocal displacement laser that can measure the polymerization shrinkage with high accuracy. The three types of SFRCs used in this study were XD (Ever X Flow Dentin), XB (Ever X Flow Bulk), and XP (EverX Posterior). In addition, CF (Clearfil majesty ES Flow) with hybrid type filler was used as a control. The measured values of the final polymerization shrinkage rate and amount of polymerization shrinkage rate when the polymerization shrinkage rate became constant (less than 0.1 µm/s) were approximated for all SFRCs. XP had a large aspect ratio of glass fiber filler and showed a significant difference from XD with a small aspect ratio (p < 0.05). There was no significant difference in the measured value of time when the polymerization contraction reached a constant speed (0.1 µm/s or less) for all SFRCs (p > 0.05). There was no significant difference in the measured values of polymerization shrinkage rate after the polymerization shrinkage reached a constant rate for all SFRCs (p > 0.05). These results show that glass fiber with large aspect ratio can alleviate polymerization shrinkage stress. The polymerization behavior of SFRC was found to be dependent on the amount of glass fiber filler, aspect ratio, and orientation.

Base Materials' Influence on Fracture Resistance of Molars with MOD Cavities

The aim of this study was to compare fracture resistance of teeth presenting medium-sized mesial-occlusal-distal (MOD) cavities using different base materials. Thirty-six extracted molars were immersed for 48 h in saline solution (0.1% thymol at 4 °C) and divided into six groups. In group A, the molars were untouched, and in group B, cavities were prepared, but not filled. In group C, we used zinc polycarboxylate cement, in group D—conventional glass ionomer cement, in group E—resin modified glass ionomer cement, and in group F—flow composite. Fracture resistance was tested using a universal loading machine (Lloyd Instruments) with a maximum force of 5 kN and a crosshead speed of 1.0 mm/min; we used NEXYGEN Data Analysis Software and ANOVA Method (p < 0.05). The smallest load that determined the sample failure was 2780 N for Group A, 865 N for Group B, 1210 N for Group C, 1340 N for Group D, 1630 N for Group E and 1742 N for Group F. The highest loads were 3050 N (A), 1040 N (B), 1430 N (C), 1500 N (D), 1790 N (E), and 3320 N (F), the mean values being 2902 ± 114 N (A), 972 ± 65 N (B), 1339 ± 84 N (C), 1415 ± 67 N (D), 1712 ± 62 N (E), and 2334 ± 662 N (F). A p = 0.000195 shows a statistically significant difference between groups C, D, E and F. For medium sized mesial-occlusal-distal (MOD) cavities, the best base material regarding fracture resistance was flow composite, followed by glass ionomer modified with resin, conventional glass ionomer cement and zinc polycarboxylate cement. It can be concluded that light-cured base materials are a better option for the analyzed use case, one of the possible reasons being their compatibility with the final restoration material, also light-cured.

The "Pre-Finishing" Approach in Direct Anterior Restorations. A Case Series

In esthetic restorations of anterior teeth the clinician has to manage several aspects in order to have a predictable outcome. A deep knowledge of the anatomy as well as the adhesive procedures and the optical properties of resin-based composites are mandatory to achieve esthetic results. Contemporary restorative materials present either several shades and different translucency properties and therefore they are able to mimic teeth’s optical behavior thus providing a natural aspect to anterior restorations. The wrong thickness of different composite layers may provide unpleasant results such as low value (grayish) restorations that often requires reintervention. A precise step-by-step procedure is therefore mandatory to provide the proper shade at the correct place. There is therefore the need of some corrections and adjustments during the layer procedure in order to avoid errors in shade positioning that could affect final result. The authors present a case series (six clinical cases) treated with the proposed technique with up to five years follow-up.

Effect of Operator Experience on Ability to Place Sequential, 2-mm-thick Increments of Composite

Because an operator has only about one chance out of three to place a composite increment within this clinically acceptable range, clinicians are advised to use an instrument (e.g., a periodontal probe with a 2-mm mark) to estimate the thickness of each increment of composite they place.

SUMMARY

Objective: To measure and compare the effect of operator experience in their ability to place composite in increments that are 2 mm thick.Methods and Materials: Fifteen volunteers from each class of freshmen, sophomores, juniors, and senior dental students and 15 clinical faculty (total number of volunteers = 75) were asked to restore a Class I preparation that was 5 mm in diameter and 8 mm deep from the cusp tips using three increments of composite that were each to be 2 mm thick. Once completed, the models were sectioned, and the thickness of each increment was measured. A repeated-measures analysis of variance (pre-set α=0.05) was used to compare the mean increment thickness with respect to operator experience level and increment sequence number. In addition, the proportion of operators placing clinically acceptable increments (between 1.75 and 2.25 mm thick), as well as the proportions from each group who placed increments that either were thinner or thicker than this range, was determined using nonparametric analyses.Results: Overall, there was an increasing trend for groups with a higher experience level to provide mean incremental thickness values close to 2 mm. However, the likelihood of placing an increment that was thicker or thinner than the manufacturer-recommended thickness was not significantly different. Regardless of the increment value, only about one-third of the increments placed fell within the desired range of 1.75 to 2.25 mm.Conclusions: Operator experience had no overwhelming significant influence on the ability to place increments of composite that were between 1.75 and 2.25 mm thick. An operator has only about one chance out of three to place a composite increment within this clinically acceptable range when using no external measurement system.

One-year results of a novel self-adhesive bulk-fill restorative and a conventional bulk-fill composite in class II cavities-a randomized clinical split-mouth study

Objectives

In the context of the phase-down of amalgam, development of easily applicable, permanent restorative materials is of high clinical interest. Aim of this study was to evaluate the clinical performance of a novel, tooth-colored, self-adhesive bulk-fill restorative (SABF, 3M Oral Care) and a conventional bulk-fill composite (Filtek One, 3M Oral Care; FOBF) for restoring class II cavities. The null-hypothesis tested was that both materials perform similar regarding clinical performance.

Materials and methods

In this randomized split-mouth study, 30 patients received one SABF and one FOBF restoration each. Scotchbond Universal (3M Oral Care) was used as adhesive for FOBF (self-etch mode), while SABF was applied directly without adhesive. Restorations were evaluated by two blinded examiners at baseline, 6 months and 12 months employing FDI criteria. Non-parametric statistical analyses and χ²-tests (α = 0.05) were applied.

Results

Thirty patients (60 restorations) were available for the 6- and 12-month recalls exhibiting 100% restoration survival. All restorations revealed clinically acceptable FDI scores at all time points and for all criteria. Only regarding esthetic properties, FOBF performed significantly better than SABF regarding surface lustre (A1) and color match and translucency (A3) at all time points and marginal staining (A2b) at 12 months.

Conclusions

The null-hypothesis could not be rejected. Both materials performed similarly regarding clinical performance within the first year of clinical service. SABF exhibited slightly inferior, but clinically fully acceptable esthetic properties as compared to FOBF.

Clinical relevance

Within the limitations of this study, the self-adhesive bulk-fill restorative showed promising results and may be recommended for clinical use.

Effect of Accelerated Aging on Some Mechanical Properties and Wear of Different Commercial Dental Resin Composites

The aim of current in vitro research was to determine the effect of hydrothermal accelerated aging on the mechanical properties and wear of different commercial dental resin composites (RCs). In addition, the effect of expiration date of the composite prior its use was also evaluated. Five commercially available RCs were studied: Conventional RCs (Filtek Supreme XTE, G-aenial Posterior, Denfil, and >3y expired Supreme XTE), bulk-fill RC (Filtek Bulk Fill), and short fiber-reinforced RC (everX Posterior). Three-point flexural test was used for determination of ultimate flexural strength (n = 8). A vickers indenter was used for testing surface microhardness. A wear test was conducted with 15,000 chewing cycles using a dual-axis chewing simulator. Wear pattern was analyzed by a three-dimensional (3D) noncontact optical profilometer. Degree of C=C bond conversion of monomers was determined by FTIR-spectrometry. The specimens were either dry stored for 48 h (37 °C) or boiled (100 °C) for 16 h before testing. Scanning electron microscopy (SEM) was used to evaluate the microstructure of each material. Data were analyzed using ANOVA (p = 0.05). Hydrothermal aging had no significant effects on the surface wear and microhardness of tested RCs (p > 0.05). While flexural strength significantly decreased after aging (p < 0.05), except for G-aenial Posterior, which showed no differences. The lowest average wear depth was found for Filtek Bulk Fill (29 µm) (p < 0.05), while everX Posterior and Denfil showed the highest wear depth values (40, 39 µm) in both conditions. Passing the expiration date for 40 months did not affect the flexural strength and wear of tested RC. SEM demonstrated a significant number of small pits on Denfil’s surface after aging. It was concluded that the effect of accelerated aging may have caused certain weakening of the RC of some brands, whereas no effect was found with one brand of RC. Thus, the accelerated aging appeared to be more dependent on material and tested material property.

Vertical Bite Rehabilitation of Severely Worn Dentitions with Direct Composite Restorations: Clinical Performance up to 11 Years

Our aim was to evaluate the clinical performance of direct composite restorations placed in patients with severely worn dentitions at an increased vertical dimension of occlusion, after up to 11 years. One hundred and sixty-four teeth in 13 patients with severely worn dentitions had been reconstructed with either microhybrid (first cohort; n = 59) or nanofilled (second cohort; n = 105) composite restorations at increased vertical dimension of occlusion using a wax-up-based template-aided placement technique. From the dental records, information about repair and replacement of restorations was obtained. Patients were clinically examined after a mean follow-up time of 10.7 years (first cohort) or 5.2 years (second cohort) using United States Public Health Service (USPHS) criteria. Subjective patient satisfaction was also recorded using visual analogue scales (VAS). The overall quality of the restorations was good with predominantly 'Alpha' and 'Bravo' scores, respectively. Nanofilled composite showed less surface degradation and better margin qualities than microhybrid composite. Of the 59 restored teeth in the first cohort, 13 restorations showed unfavorable events after 10.7 years, of which ten could be repaired. In the second cohort, 23 of 105 restorations showed unfavorable events, which could all be repaired. VAS scores revealed high patient satisfaction with the treatment approach. In conclusion, direct composite restorations placed at an increased vertical dimension of occlusion show good clinical long-term performance in patients with severe tooth wear.

Interfacial Stress and Bond Strength of Bulk-Fill or Conventional Composite Resins to Dentin in Class II Restorations

The aim was to evaluate the microtensile bond strength (mTBS) to dentin and interfacial stress in a class II cavity restored with bulk-fill or conventional composite resins and the margin interfaces. Vertical slot class II cavities in the mesial face, with the gingival end in dentin, were prepared in 72 third molars, being divided into groups (n=24): G1-Tetric N-Ceram; G2-Tetric N-Ceram Bulk-Fill; G3-SonicFill. Clearfil SE Bond adhesive system was used in all groups. Half of the teeth in each group (n=12) were submitted to thermo-mechanical cycling (TMC). Restored teeth (n=9) were cut perpendicular to obtain beams, which were submitted to a mTBS test in an EMIC machine. The cervical margins in dentin of the restored teeth (n=3) were assessed using SEM through epoxy resin replicas as well as the section of the restoration. Interfacial stresses after load application were calculated by 2D finite element analysis. The mTBS means-MPa followed by different letters represent statistical difference by ANOVA and Games-Howell's test (p<0.05): Without TMC: G1-15.68±6.10a; G2-10.08±5.21ab; G3-7.98±3.76b. With TMC: G1-9.70±5.52a; G2-5.79±1.42a; G3-4.37±1.87a. Interfacial stress (MPa) was 4.4 for SonicFill, 3.9 for Tetric N-Ceram, and 3.5 for Tetric N-Ceram Bulk-Fill. SEM images showed continuous margins for all composite resin restorations. It was possible to conclude that SonicFill obtained a slightly higher interfacial stress and lower bond strength to dentin in comparison with Tetric N-Ceram and Tetric N-Ceram Bulk-Fill. Continuous margin interfaces were obtained for Tetric N-Ceram, Tetric N-Ceram Bulk-Fill, and SonicFill. However, voids were observed in the SonicFill restorations.

Current perspectives on dental adhesion: (2) Concepts for operatively managing carious lesions extending into dentine using bioactive and adhesive direct restorative materials

This article reviews the current concepts for operatively managing carious lesions extending into dentine with minimal removal of tooth structure and restoring with dentine adhesives and direct composite resin. It looks sequentially at the operative steps involved including remineralisation with bioactive cements, bonding to caries-affected dentine including smear-layer modification using HOCl, creation of an acid-base resistance zone,steps to optimise the performance of all-in-one adhesives, and incremental placement of direct composite resin to improve bond strengths to cavity floor dentine. It explores how understanding the phenomenon of colour-shifting at the composite resin-enamel/dentine restoration borders can help in creating near "invisible" restoration margins through a "chameleon" effect. With the increased risks of transmission of Covid-19 when aerosol generating procedures are carried out in Dentistry, following a minimally invasive approach to managing dental caries should be given serious consideration.

Nano-CT as tool for characterization of dental resin composites

Technological advances have made it possible to examine dental resin composites using 3D nanometer resolution. This investigation aims to characterize existing dental nano-hybrid and micro-hybrid resin composites through comparing and contrasting nano-computed tomography (nano-CT) with micro-CT and high-resolution SEM images. Eight commercially available and widely used dental resin composites, 2 micro-hybrid and 6 nano-hybrid were researched. Cured samples were examined and characterized using nano-CT (resolution 450 nm) and compared with micro-CT images (resolution 2 µm). Acquired images were reconstructed and image analysis was carried out to determine porosity and pore morphology. A comprehensive comparison of scanning micrograph images unsurprisingly revealed that the nano-CT images displayed greater detail of the ultrastructure of cured dental resin composites. Filler particle diameters and its volumes were lower when measured using nano-CT, porosity being higher where analysed at higher resolution. There were large variations between the examined materials. Fewer voids were found in Tetric EvoCeram and IPS Empress Direct, the smallest pores being found in Universal XTE and Tetric EvoCeram. Nano-CT was successfully used to investigate the morphology of dental resin composites and showed that micro-CT gives a lower porosity and pore size but overestimates filler particle size. There were large discrepancies between the tested composites. Evidence of porosities and pores within a specimen is a critical finding and it might have a detrimental effect on a material’s clinical performance.

Treatment options for large posterior restorations: a systematic review and network meta-analysis

BACKGROUND

The best treatment option for large caries in permanent posterior teeth is still a matter of uncertainty in dental literature. The authors conducted a network meta-analysis to address the challenges related to rehabilitation of these teeth.

TYPES OF STUDIES REVIEWED

The authors selected prospective and retrospective studies that compared at least 2 different treatment alternatives for permanent teeth with a minimum of 5 years of follow-up. The authors searched databases from MEDLINE, Scopus, Cochrane Library, and Web of Science in October 2019 without language or year of publication restrictions.

RESULTS

From 11,263 studies identified, 43 studies fulfilled the eligibility criteria and were included in the final review. Only 13 studies were randomized controlled trials and were classified as low risk of bias. Gold (annual failure rate of 0.29%) and metal ceramic (annual failure rate of 0.52%) crowns performed better for indirect restorations and direct resin composite performed better for direct restorations (annual failure rate of 2.19%). The most substantial comparisons were between feldspathic and glass ceramics, followed by direct resin composite and amalgam; there were no statistically significant differences between these interventions. Results of the pairwise meta-analysis showed mainly glass ionomer as significantly more prone to failure than amalgam and direct composite resin.

CONCLUSIONS AND PRACTICAL IMPLICATIONS

Reference standard direct and indirect materials except for glass ionomer can be used for restorations of large posterior caries.

Young's modulus and Poisson ratio of composite materials: Influence of wet and dry storage

In the oral environment dental materials are subject to a wet condition what might in time change their elastic properties. In this article, we evaluated the influence of the storage condition (dry versus wet) on the Young's modulus and the Poisson ratio in compression of three composite materials. The data of the Young's modulus and Poisson ratio published of dental composite materials are not always comparable, due to different test methods and sample dimensions influencing the results. Therefore, we established the degree of exactness of the results out of the test set-up used. Since the present study depicted differences of the properties after dry and wet storage, the elastic properties should be measured after wet storage. The bonding between the matrix and the filler particles showed to have an influence on the elastic properties and on the influence of a wet environment.

Spatial Distribution of the Micro-Mechanical Properties in High-Translucent CAD/CAM Resin-Composite Blocks

Industrially cured, high-translucent computer-aided design/computer-aided manufacturing (CAD/CAM) resin-based composites (RBC) are the most recently launched dental restoratives. Clinical treatments and laboratory tests are based on a homogeneous distribution of properties within CAD/CAM blocks to obtain constant and reproducible results. The study therefore aims to determine the spatial distribution of various micro-mechanical parameters (Vickers hardness, Martens hardness, indentation modulus, creep, elastic and total indentation work) in five representative CAD/CAM RBCs. The properties of the tooth structure were evaluated under similar conditions. Filler size and shape were analyzed by scanning electron microscopy. A multivariate analysis (general linear model) identified a very strong influence of the material on all measured properties (p < 0.001; partial eta squared η_P² > 0.943), whereby the most sensitive parameters when identifying differences within regions were the indentation modulus and the elastic indentation work. CAD/CAM RBC blocks show gradually varying properties that can increase or decrease from central to peripheral areas regardless of the chemical composition of the materials or the inorganic filler fraction. The degree of variation in the measured properties is material-specific and less than 8.7%. Clinical applications and in vitro study designs should consider slight inhomogeneity in CAD/CAM RBC blocks, while the location of the regions with best mechanical performance depends on the material.

In vitro wear of dual-cured bulkfill composites and flowable bulkfill composites

OBJECTIVES

The objective of this study is to test the wear of dual-cured bulkfill and flowable bulkfill composites.

MATERIALS AND METHODS

Six dual-cured bulkfill composites, Cention, Cention-Exp, Activa, Fill-up, Hyperfil Injectafill, and two flowable bulkfill composites Tetric Evoflow BulkFill and G-aenial Universal Flo were tested in this study (n = 8). Each composite was applied into an aluminum sample holder and cured with a Valo Grand (1230 mW/cm² ) or self-cured according to manufacturer's recommendations, and stored in water for 3 weeks. The samples were subjected to 120 000 load cycles of 49 N (CS-4) against spherical steatite antagonists and simultaneously subjected to 4440 thermocycles (5°C-55°C). At intervals between load cycles, polyvinyl siloxane impressions were taken and scanned with a True Definition Laser Scanner. The volumetric wear was calculated using image software (Geomagic). Microscopic images of selected wear facets and their corresponding worn antagonists were obtained using SEM. All data were analyzed using analysis of variance (ANOVA) and Tukey post hoc test for multiple comparison (α = .05; β = .2).

RESULTS

The load cycles volumetric wear-increase was linear. Two-way ANOVA showed significant main effects (material and light-cured) and significant interactions. Self-cured materials (mean = 0.38 mm³ ) showed more wear than light-cured materials (mean = 0.35mm³ ).

CONCLUSIONS

The bioactive materials except Activa light-cured showed significantly more wear than the flowable composites.

CLINICAL SIGNIFICANCE

This study demonstrated that most of the dual-cured composites, if light-cured, showed the same wear as the flowable composites used as control. Therefore, to obtain adequate wear resistance the dual-cured composites should be routinely light-cured.