Filler characteristics of modern dental resin composites and their influence on physico-mechanical properties

3D micro-CT and O-PTIR spectroscopy bring new understanding of the influence of filler content in dental resin composites

BACKGROUND

Dental resin composites' performance is intricately linked to their polymerisation shrinkage characteristics. This study compares polymerisation shrinkage using advanced 3D micro-computed tomography (micro-CT) and traditional 2D linear assessments. It delves into the crucial role of filler content on shrinkage and the degree of conversion in dental resin composites, providing valuable insights for the field.

METHODS

Five experimental dental composite materials were prepared with increasing filler contents (55-75 wt%) and analysed using either 3D micro-CT for volumetric shrinkage or a custom-designed linometer for 2D linear shrinkage. The degree of conversion was assessed using Optical Photothermal Infrared (O-PTIR) and Fourier-Transform Infrared (FTIR) spectroscopy. Light transmittance through a 2-mm layer was evaluated using a NIST-calibrated spectrometer. Scanning Electron Microscopy (SEM) and Energy-Dispersive X-ray Spectroscopy (EDX) examined surface morphology and elemental distribution. Correlation between the investigated parameters was determined using Spearman correlation analyses.

RESULTS

The study found significant differences in polymerisation-related properties among different filler content categories, with volumetric shrinkage consistently demonstrating higher mean values than linear shrinkage across most groups. Volumetric shrinkage decreased with increasing curing depth, showing no direct correlation between filler content and shrinkage levels at different curing depths. The results highlighted a strong negative correlation between filler content and degree of conversion, volumetric and linear shrinkage, as well as maximum shrinkage rate. Light transmittance showed a moderate correlation with the filler content and a weak correlation with other tested parameters.

CONCLUSIONS

This study underscores the importance of considering both volumetric and linear shrinkage in the design and analysis of dental composite materials. The findings advocate optimising filler content to minimise shrinkage and enhance material performance. Integrating micro-CT and O-PTIR techniques offers novel insights into dental composites' polymerisation behaviour, providing a foundation for future research to develop materials with improved clinical outcomes.

Surface and bulk viscoelastic stability of solvent-stored bulk-fill resin-based composite

OBJECTIVE

Investigate the effect of solvent-storage on surface hardness and bulk creep of fast photo-cured bulk-fill resin-based composite (RBC) compared to conventionally irradiated bulk-fill RBCs.

METHODS

Three bulk-fill RBCs were studied: Tetric® PowerFill (fast photo-cured bulk-fill RBC) (TPF), Tetric EvoCeram® (EVO), and GrandioSO® x-tra (GSOx) (conventional). Disk-shaped specimens of clinically realistic thickness (4 mm) were prepared from each material for: Group A: surface measurements (18 mm diameter) and Group B: 4 mm diameter for bulk compressive creep measurements. Group A disks were light-cured from the upper 'occlusal' surface for either 3 s or 20 s according to the manufacturer's recommendation. Martens hardness (HM) of both top and bottom surfaces of each specimen were measured. Group B: 4 × 4 mm cylindrical specimens were fully cured to measure bulk creep (CB). A 20 MPa static compressive stress was applied for 2 h, followed by 2 h of unloading. Strain deformation was recorded continuously for 4 h. Both Martens and bulk creep studies were performed under the following storage conditions at 37 °C: (i) dry at 24 h post curing (baseline), and (ii) after 7 and 30 d of storage in two different media: distilled water (DW) and 75 % ethanol/water (75 % E/W).

RESULTS

At baseline, HM for all materials ranged from 587 to 439 N/mm2 (top) and 398 to 342 N/mm2 (bottom). After 30 d of solvent-storage, more pronounced HM changes were observed, with the bottom surface being more affected. Normalised HM for TPF decreased by 44 % after 30 d in 75 % E/W. Maximum creep strain ranged from 1.1 % to 2.1 % at baseline, and after 30 d in 75 % E/W this increased from 1.9 % to 2.9 %. Depending on the material and storage condition, the percentage creep strain recovery after 30 d ranged between 65.2 % and 80 %. Increased filler loading in the bulk-fill RBCs decreased the creep strain magnitude and increased the surface hardness.

SIGNIFICANCE

Solvent storage decreased the Martens hardness of both upper and lower surfaces and increased the bulk creep characteristics of bulk-fill RBCs. Nevertheless, there was a similar relative stability in surface hardness and viscoelastic stability of fast-cured PowerFill compared to conventionally irradiated RBCs.

On the suitability of photocuring-assisted DIW for manufacturing complex prosthesis from commercial dental composites

A 3-D printing method to produce dental prostheses of complex shapes from a commercial, photocurable resin-ceramic slurry is developed and optimized. The microstructure, mechanical properties and wear behavior of the resulting material are evaluated and compared with a conventional/control sample and other ceramic-polymer dental composites. Commercial resin-ceramic dental slurries can be successfully extruded and appropriately photocured in a low cost 3-D printing system to produce cost-efficient complex dental parts that could be used in indirect restorations. The printing process does not appreciably introduce defects in the material and the 3-D printed composites exhibit mechanical properties (hardness, elastic modulus) and wear resistance comparable to the control material and analogous, conventional dental composites. The main wear mechanisms under sliding contact against a hard antagonist are plastic deformation at the asperity level and ceramic particle pull-out due to filler/matrix interfacial weakness.

The effect of different liquids on the surface roughness and color stability of single shade and nanohybrid resin composites: An AFM and SEM analysis

The aim of this study is to evaluate the surface roughness (SR) and color changes of single-shade and nanohybrid resin-based restorative materials (RBC) after immersion in liquids at different pH values. For RBCs, a total of 120 specimens, 30 for each material, were prepared using 10 mm diameter and 2 mm thick molds. For flowable bulk fill RBC, a total of 40 specimens, 10 for each material, were prepared using 10 mm diameter and 4 mm thick molds (n = 10). After initial color and SR measurements, samples were stored in the liquids for 14 days and all of the measurements were repeated on 14th days. Scanning electron microscopy and atomic force microscopy analyzes were performed in all groups. When SR results are examined; among all liquids, the highest SR value was observed in the Carisma Diamond One (CDO) group, while the lowest SR value was observed in the Omnichroma Flow Bulk (OMF) group (p < .05). When the color changes (ΔE) results are examined; it was observed that CDO group had highest color change and OMF group had the lowest values. It has been observed that among the liquids, the liquids that affect the ΔE values of the materials the most are coffee and cola. When the ΔE values of the subgroups of the materials were examined, there was a statistically significant difference in all subgroups of RBCs (p < .05). While acidic liquids increased the SR of RBCs, coffee more affected the color change of RBCs. RESEARCH HIGHLIGHTS: Clinicians should keep in mind that the RBCs tested may change their surface properties and colors when exposed to various liquids. People who have RBCs should pay attention to the consumption of acidic and highly pigmented liquids.

An in vitro evaluation of the fatigue behavior of resin composite materials as part of a translational research cycle

PURPOSE

This study aimed to reproduce and translate clinical presentations in an in vitro set-up and evaluate laboratory outcomes of mechanical properties (flexural strength, fatigue resistance, wear resistance) and link them to the clinical outcomes of the employed materials in the Radboud Tooth Wear Project (RTWP).

MATERIALS AND METHODS

Four dental resin composites were selected. 30 discs (Ø12.0 mm, 1.2 mm thick) were fabricated for each of Clearfil TM AP-X (AP), Filtek TM Supreme XTE (FS), Estenia TM C&B (ES), and Lava Ultimate (LU). Cyclic loading (200 N, 2 Hz frequency) was applied concentrically to 15 specimens per group with a spherical steatite indenter (r = 3.18 mm) in water in a contact-load-slide-liftoff motion (105 cycles). The wear scar was analysed using profilometry and the volume loss was digitally computed. Finally, all specimens were loaded (fatigued specimens with their worn surface loaded in tension) until fracture in a biaxial flexure apparatus. The differences in volume loss and flexural strength were determined using regression analysis.

RESULTS

Compared to AP and FS, ES and LU showed a significantly lower volume loss (p < 0.05). Non-fatigued ES specimens had a similar flexural strength compared to nonfatigued AP, while non-fatigued FS and LU specimens had a lower flexural strength (p < 0.001; 95 %CI: -80.0 - 51.8). The fatigue test resulted in a significant decrease of the flexural strength of ES specimens, only (p < 0.001; 95 %CI: -96.1 - -54.6).

CLINICAL RELEVANCE

These outcomes concur with the outcomes of clinical studies on the longevity of these composites in patients with tooth wear. Therefore, the employed laboratory test seems to have the potential to test materials in a clinically relevant way.

Correlation between Dental Composite Filler Percentage and Strength, Modulus, Shrinkage Stress, Translucency, Depth of Cure and Radiopacity

Filler content in dental composites is credited for affecting its physical and mechanical properties. This study evaluated the correlation between the filler percentage and strength, modulus, shrinkage stress, depth of cure, translucency and radiopacity of commercially available high- and low-viscosity dental composites. Filler weight percentage (wt%) was determined through the burned ash technique (800 °C for 15 min). Three-point bend flexural strength and modulus were measured according to ISO 4049 with 2 mm × 2 mm × 25 mm bars. Shrinkage stress was evaluated using a universal testing machine in which composite was polymerized through two transparent acrylic rods 2 mm apart. Shrinkage was measured from the maximum force following 500 s. The translucency parameter (TP) was measured as the difference in color (ΔE00) of 1 mm thick specimens against white and black tiles. The depth of cure was measured according to ISO 4049 in a cylindrical metal mold (4 mm diameter) with a 10 s cure. Radiopacity was measured by taking a digital X-ray (70 kVp for 0.32 s at 400 mm distance) of 1 mm thick specimens and comparing the radiopacity to an aluminum step wedge using image analysis software. The correlation between the filler wt% and properties was measured by Pearson's correlation coefficient using SPSS. There was a positive linear correlation between the filler wt% and modulus (r = 0.78, p < 0.01), flexural strength (r = 0.46, p < 0.01) and radiopacity (r = 0.36, p < 0.01) and negative correlation with translucency (r = -0.29, p < 0.01). Filler wt% best predicts the modulus and strength and, to a lesser extent, the radiopacity and translucency. All but two of the high- and low-viscosity composites from the same manufacturer had statistically equivalent strengths as each other; however, the high-viscosity materials almost always had a statistically higher modulus. For two of the flowable composites measured from the same manufacturer (3M and Dentsply), there was a lower shrinkage stress in the bulk-fill version of the material but not for the other two manufacturers (Ivoclar and Tokuyama). All flowable bulk-fill composites achieved a deeper depth of cure than the flowable composite from the same manufacturer other than Omnichroma Flow Bulk.

Transcriptome changes in humans acutely exposed to nanoparticles during grinding of dental nanocomposites

Aim: Today, there is a lack of research studies concerning human acute exposure to nanoparticles (NPs). Our investigation aimed to simulate real-world acute inhalation exposure to NPs released during work with dental nanocomposites in a dental office or technician laboratory. Methods: Blood samples from female volunteers were processed before and after inhalation exposure. Transcriptomic mRNA and miRNA expression changes were analyzed. Results: We detected large interindividual variability, 90 significantly deregulated mRNAs, and 4 miRNAs when samples of participants before and after dental nanocomposite grinding were compared. Conclusion: The results suggest that inhaled dental NPs may present an occupational hazard to human health, as indicated by the changes in the processes related to oxidative stress, synthesis of eicosanoids, and cell division.

Effect of gastric acids on the mechanical properties of conventional and CAD/CAM resin composites - An in-vitro study

OBJECTIVES

Dental erosion in patients with gastroesophageal reflux disease (GERD) is a current and frequent condition that may compromise the mechanical properties and clinical durability of resin-based composites (RBCs). This study assessed the mechanical properties of conventional and computer-aided design/computer-aided manufacturing (CAD/CAM) RBCs subsequent to simulated gastric acid aging.

MATERIALS AND METHOD

Three conventional and three CAD/CAM composites were assessed. They were divided into an experimental group (exposed to simulated gastric acid aging) and a control group (no aging). Both groups were analyzed for Vickers microhardness (VHN), wear and flexural strength over a period of six months. The failure rate probability for each RBC was calculated through the Weibull cumulative distribution function (m). Statistical analysis was conducted using repeated measures ANOVA, 3-way ANOVA, a non-parametric Kruskal-Wallis and U Mann-Whitney tests (α = 0.05).

RESULTS

The mechanical properties of all the RBCs dropped significantly after aging (p < 0.05). Lower VHN and flexural strength values, along with greater wear values were evident in the experimental groups, though the effects of the treatment varied between RBCs. The Weibull m of all the RBCs decreased over time.

CONCLUSION

Conventional RBCs might show greater reduction in mechanical properties compared to CAD/CAM RBCs when exposed to gastric acid attack. Thus, CAD/CAM composites may represent a suitable choice for the treatment of patients presenting erosive issues.

Evaluation of Shear Bond Strengths of 3D Printed Materials for Permanent Restorations with Different Surface Treatments

The development of high-filled 3D printing resin necessitates a bonding protocol for dental indirect restorations to achieve optimal bond strength after cementation. This study evaluates shear bond strengths of high-filler 3D printed materials for permanent restorations with various surface treatments. Rodin Sculpture 1.0 (50% lithium disilicate fillers) and 2.0 Ceramic Nanohybrid (>60% zirconia and lithium disilicate fillers) were tested, with Aelite All-Purpose Body composite resin as control. Samples were prepared, post-cured, and sandblasted with alumina (25 µm). Surface roughness was analyzed using an optical profilometer. Two bonding protocols were compared. First, groups were treated with lithium disilicate silane (Porcelain Primer) or zirconia primer (Z-Prime Plus) or left untreated without a bonding agent. Beam-shaped resin cement (DuoLink Universal) specimens were bonded and stored in a 37 °C water bath. Second, additional sets of materials were coated with a bonding agent (All-Bond Universal), either followed by silane application or left untreated. These sets were then similarly stored alongside resin cement specimens. Shear bond tests were performed after 24 h. SEM images were taken after debonding. One-Way ANOVA and post hoc Duncan were performed for the statistical analysis. Rodin 1.0 exhibited increased adhesive failure with silane or zirconia primer coating, but significantly improved bond strengths with bonding agent application. Rodin 2.0 showed consistent bond strengths regardless of bonding agent application, but cohesive failure rates increased with bonding agent and filler coating. In all groups, except for Rodin 1.0 without bonding agent, silane coating increased cohesive failure rate. In conclusion, optimal shear bond strength for high-filler 3D printing materials can be achieved with silane coating and bonding agent application.

Comparative Assessments of Dental Resin Composites: A Focus on Dense Microhybrid Materials

The performance of dental resin composites is crucially influenced by the sizes and distributions of inorganic fillers. Despite the investigation of a variety of functional particles, glass fillers and nanoscale silica are still the predominant types in dental materials. However, achieving an overall improvement in the performance of resin composites through the optimization of their formulations remains a challenge. This work introduced a "dense" microhybrid filler system with 85 wt % filler loading, leading to the preparation of self-developed resin composites (SRCs). Comparative evaluations of these five SRCs against four commercial products were performed, including mechanical property, polymerization conversion, and shrinkage, along with water sorption and solubility and wear resistance. The results showed that among all SRC groups, SRC3 demonstrated superior mechanical performance, high polymerization conversion, reduced shrinkage, low water absorption and solubility, and acceptable wear resistance. In contrast to commercial products, this optimal SRC3 material was comparable to Z350 XT in flexural and diametral tensile strength and better in flexural modulus and surface hardness. The use of a "dense" microhybrid filler system in the development of resin composites provides a balance between physicochemical property and wear resistance, which may be a promising strategy for the development of composite products.

Effect of canal medicaments triple antibiotic paste, Bio-C Temp, and Nano-silver gel activated by visible blue light on canal dentin microhardness and extrusion bond strength of AH plus sealer: A SEM and EDX analysis

AIM

Assessment of contemporary canal medicaments (Triple antibiotic paste (TAP), Bio-C Temp, and Nano silver gel activated by visible blue light on the dentin microhardness (MH) and push-out bond strength (PBS) of AH plus endodontic sealer.

METHOD

Sixty extracted premolars were obtained and decontaminated. Canal cleaning and shaping were performed. The samples were randomly allocated into four groups based on the intracanal medicaments. Group 1= CH paste, Group 2= TAP, Group 3= Bio-C Temp, and Group 4= Nano-silver gel activated by visible blue light. MH assessment was performed using a Vickers Microhardness tester. Forty specimens, ten from each group underwent root canal obturation. PBS and failure mode evaluation were performed. ANOVA and Post Hoc Tukey test were utilized to conduct intra and inter-group comparisons.

RESULTS

The maximum outcome of surface hardness was presented by Group-3 (Bio-C Temp®) specimens. However, minimum scores of MH were displayed by Group 1 (CH) treated teeth. The highest outcomes of EBS were exhibited by the cervical third of Group 3 (Bio-C Temp®) samples. The apical section of Group 4 Teeth with Nano Silver gel activated by visible blue light revealed the lowest scores of bond integrity.

CONCLUSION

Bio-C Temp and TAP proved to be better intracanal medicament than other tested groups in terms of the push-out bond strength of the sealer. TAP displayed lower microhardness as compared to the Bio-C Temp.

Repairability of aged dimethacrylate-free ORMOCER-based dental composite resins with different surface roughening methods and intermediate materials

STATEMENT OF PROBLEM

The repair of damaged composite resin restorations has been recommended as a conservative treatment option. However, a reliable protocol for repairing ORMOCER-based restorations is lacking.

PURPOSE

The purpose of this in vitro study was to investigate the effect of different surface roughening methods, repair composite resins, and intermediate materials on the repair bond strength of a dimethacrylate-free ORMOCER-based composite resin.

MATERIAL AND METHODS

Cylindrical composite resin specimens (Admira Fusion) were roughened by using hydrofluoric acid (HF) or a diamond rotary instrument. In both groups, 4 types of intermediate materials were used (Monobond-S, Clearfil SE bond [second bottle], Clearfil Universal bond, GC Composite Primer), and then half of the specimens were repaired with a similar composite resin, and the other half with dimethacrylate composite resin (Clearfil-APX). The specimens (n=20) were then subjected to repair bond strength and failure mode evaluation. The data were analyzed by using the Weibull test, 3-way and 1-way ANOVA, and the Tukey honestly significant difference (HSD) test (α=.05).

RESULTS

All variables, including the surface roughening method, intermediate material, and repair composite resin, had a significant effect on repair bond strength (P<.001). The lowest repair bond strength values were obtained in the group roughened with HF, prepared with Monobond-S, and repaired with Admira Fusion, and the highest values were obtained in the group roughened with a rotary instrument, prepared with GC Composite Primer, and repaired with Clearfil APX (P<.05). All experimental groups had a lower bond strength than the cohesive and control groups (P<.05). In all experimental groups, the predominant failure modes were adhesive and mixed.

CONCLUSIONS

The use of a diamond rotary instrument was a more reliable method of creating roughness, and different intermediate materials based on the clinical situation can be used to repair dimethacrylate-free ORMOCER-based composite resin with similar or different composite resins. However, in general, the highest repair bond strengths were achieved with Clearfil APX-repaired specimens.

Experimental characterization and finite element investigation of SiO2 nanoparticles reinforced dental resin composite

In this study, a commercial dental resin was reinforced by SiO2 nanoparticles (NPs) with different concentrations to enhance its mechanical functionality. The material characterization and finite element analysis (FEA) have been performed to evaluate the mechanical properties. Wedge indentation and 3-point bending tests were conducted to assess the mechanical behavior of the prepared nanocomposites. The results revealed that the optimal content of NPs was achieved at 1% SiO2, resulting in a 35% increase in the indentation reaction force. Therefore, the sample containing 1% SiO2 NPs was considered for further tests. The morphology of selected sample was examined using field emission scanning electron microscopy (FE-SEM), revealing the homogeneous dispersion of SiO2 NPs with minimal agglomeration. X-ray diffraction (XRD) was employed to investigate the crystalline structure of the selected sample, indicating no change in the dental resin state upon adding SiO2 NPs. In the second part of the study, a novel approach called iterative FEA, supported by the experiment wedge indentation test, was used to determine the mechanical properties of the 1% SiO2-dental resin. Subsequently, the accurately determined material properties were assigned to a dental crown model to virtually investigate its behavior under oblique loading. The virtual test results demonstrated that most microcracks initiated from the top of the crown and extended through its thickness.

Influence of Specimen Dimension, Water Immersion Protocol, and Surface Roughness on Water Sorption and Solubility of Resin-Based Restorative Materials

The evaluation of water sorption and solubility is pivotal for the development of new resin-based restorative materials with the potential for clinical application. The purpose of the present study was to evaluate the influence of the specimen dimension, water immersion protocol, and surface roughness on the water sorption and solubility of three resin-based restorative materials. Disk-shaped specimens of 15 mm × 1 mm, 10 mm × 1 mm, and 6 mm × 1 mm were produced with a composite resin (Z100), a resin cement (RelyX ARC), and an adhesive system (Single Bond 2-SB2). The specimens were immersed in distilled water according to four protocols: ISO (all the specimens for each group were vertically immersed in 50 mL); IV-10 (the specimens were individually and vertically immersed in 10 mL); IH-10 (the specimens were individually and horizontally immersed in 10 mL); and IH-2 (the specimens were individually and horizontally immersed in 2 mL). The surface roughness (Sa and Sp) was evaluated using an atomic force microscope, and the degree of conversion was determined using FT-IR spectrometry. The specimen dimension and water immersion protocol had no effect on water sorption and solubility. For the three resin-based restorative materials, Sp was higher than Sa. The degree of conversion was not influenced by the specimen dimension. The variations in the specimen dimension and water immersion protocol compared to those determined by ISO 4049 did not prevent the comparison between the values of water sorption and solubility obtained for a given resin-based restorative material.

Effect of different finishing and polishing systems on surface properties of universal single shade resin-based composites

BACKGROUND

Recently, universal single-shade resin composites have become increasingly available in the dental market. The modification of their composition can have an inadvertent effect on their physical and surface properties, and subsequently determinantal effect on their clinical function and longevity. Therefore, this study aimed to evaluate the effect of different finishing and polishing (F/P) systems on surface roughness (Ra), surface gloss (GU), and Vickers microhardness (VMH) of universal single-shade RBCs.

MATERIALS AND METHODS

Four commercial RBCs were used; the universal single-shade RBCs were Omnichroma, Charisma® Diamond ONE, and Vittra APS Unique, and a conventional nanocomposite Filtek™ Z250 XT was used as a control. The 3 F/P systems were Sof-Lex™ XT, Enhance®/PoGo®, and Diacomp® Plus Twist. A total of 160 discs were used for the 3 F/P system groups for all RBCs (n = 10). After F/P, the Ra, GU, and VMH were assessed. The data were analyzed using 2-way ANOVA at p-value < 0.05.

RESULTS

Significant differences were found among the four RBCs and the 3 F/P systems (p < .000). Omnichroma showed the lowest Ra and acceptable GU, but the lowest VMH. Charisma showed the highest Ra, acceptable GU, and VMH. Vittra showed acceptable Ra, GU, and VMH and Filtek showed the highest GU, VMH, and acceptable Ra.

CONCLUSION

Although conventional nanohybrid RBC (Filtek Z250 XT) showed better GU and VMH values, the universal single-shade RBCs demonstrated comparable surface properties. The highest GU & VMH and lowest Ra were achieved by Diacomp followed by Enhance and Soflex.

A Review of Recent Advances in Human-Motion Energy Harvesting Nanogenerators, Self-Powering Smart Sensors and Self-Charging Electronics

In recent years, portable and wearable personal electronic devices have rapidly developed with increasing mass production and rising energy consumption, creating an energy crisis. Using batteries and supercapacitors with limited lifespans and environmental hazards drives the need to find new, environmentally friendly, and renewable sources. One idea is to harness the energy of human motion and convert it into electrical energy using energy harvesting devices-piezoelectric nanogenerators (PENGs), triboelectric nanogenerators (TENGs) and hybrids. They are characterized by a wide variety of features, such as lightness, flexibility, low cost, richness of materials, and many more. These devices offer the opportunity to use new technologies such as IoT, AI or HMI and create smart self-powered sensors, actuators, and self-powered implantable/wearable devices. This review focuses on recent examples of PENGs, TENGs and hybrid devices for wearable and implantable self-powered systems. The basic mechanisms of operation, micro/nano-scale material selection and manufacturing processes of selected examples are discussed. Current challenges and the outlook for the future of the nanogenerators are also discussed.

Novel low-shrinkage dental resin containing microcapsules with antibacterial and self-healing properties

Dental resin restorations commonly fail because of fractures and secondary caries. The aim of this research was to synthesize a novel low-shrinkage dental resin with antibacterial and self-healing properties. The low-shrinkage dental resin was obtained by incorporating a 20 wt% anti-shrinkage mixture of an expanding monomer 3,9-diethyl-3,9-dimethylol -1,5,7,11-tetraoxaspiro[5,5] undecane and an epoxy resin monomer diallyl bisphenol A diglycidyl ether (1:1, referred as "UE") and different mass fractions of self-healing antibacterial microcapsules (0%, 2.5%, 5%, 7.5%, and 10%) were incorporated into the matrix to prepare multifunctional dental resin. Polymerization shrinkage, mechanical properties, antibacterial activity, self-healing ability, and cytotoxicity of this dental resin were evaluated. The polymerization volumetric shrinkage of resin containing 20 wt% UE and 7.5 wt% microcapsules was reduced by 30.12% (4.13% ± 0.42%) compared with control. Furthermore, it exhibited high antibacterial activity and a good self-healing efficiency of 71% without adversely affecting the mechanical property and cell viability. This novel multifunctional dental resin with low polymerization shrinkage and excellent antibacterial activity and self-healing capability has potential application as a dental resin material to decrease the incidence of fractures and secondary caries.

The influence of pre-heating the restoration and luting agent on the flexural strength of indirect ceramic and composite restorations

Background

This study investigated the impact of luting procedure and restoration thicknesses on the flexural strength of CAD/CAM restorations. Traditional luting agents have been questioned in favor of pre-heated resin composites or flowable composites.

Materials and Methods

400 disc-shaped restorations (lithium disilicate [IPS e.max CAD] or resin composite [Tetric CAD, Ivoclar]) were cemented onto dentin analog discs using different procedures (n = 20): dual-curing resin cement (Panavia V5), light-curing resin cement (Panavia Veneer LC), pre-heated resin composite (Clearfil™ AP-X) with or without pre-heated restoration, and high-filled flowable composite (Clearfil Majesty™ Flow). The biaxial flexural strength was calculated.

Results

There were significant effects of material, thickness, and luting procedure on flexural strength (p < 0.001). Resin composite specimens exhibited lower flexural strength (90 MPa) compared to lithium disilicate specimens (571 MPa), with thicker restorations (338 MPa) being stronger than thinner ones (323 MPa). Light-curing cement showed the highest strength (408.8 MPa)A, followed by dual-curing cement (362 MPa)B, pre-heated cement with pre-heated composite (318 MPa)C, pre-heated composite (304 MPa)C, and flowable resin composite (259 MPa)D. The light-curing cement yielded similar results to the pre-heated resin composite associated or not with the pre-heated crown for the thicker lithium disilicate specimens, whereas for the thinner lithium disilicate specimens all luting procedures performed similarly. Thin resin composite discs showed higher flexural strength when luted with light-curing cement, whereas the luting procedure had less influence for the thicker restorations.

Conclusion

Luting procedures impact the flexural strength of CAD/CAM lithium disilicate and resin composite restorations. Pre-heated resin composite, with or without pre-heated restoration, can replace dual-curing cement. Nevertheless, light-curing cement is superior for resin composite and 1.5 mm lithium disilicate restorations.

In Vitro Effect of Mouthrinses on the Microhardness of Three Different Nanohybrid Composite Resins

Introduction

Daily use of different mouthrinses at home or in the dental office can alter the properties of resin hardness. The present study aimed to compare Vickers microhardness (VHN) in vitro of nanohybrid composite resins (NCRs) immersed in mouthrinses.

Materials and Methods

In total, 120 discs (10 ⨯ 2 mm) were prepared from three NCR shade A2 (n = 40/group) with FiltekTM Z350 XT (Z350XT), Tetric EvoCeram (TEC), and Polofil NHT (PNHT). The specimens were incubated in artificial saliva (37°C ⨯ 24 hr). Specimens were distributed into four mouthrinses (n = 10/group) of artificial saliva (control), chlorhexidine (CHX 0.12%, pH 5.6), cetylpyridine chloride (CPC 0.075%, pH 5.84), and CHX 0.12% + CPC 0.05% (pH 6.2) (2 times/day, 2' ⨯ 12 hr). The VHN (300 gf/10") was measured after 24 hr, 14, and 21 days. Data were analyzed by three-way analysis of variance, followed by post hoc Tukey analysis at 0.05 level of significance.

Results

The results revealed a global effect of the interaction of the mouthrinses ⨯ time between NRC evaluated (P=0.001). Baseline VHN in PNHT and Z350XT was higher than TEC. Within each group of NCR, VHN of CHX + CPC > other mouthrinses (PNHT/14 days; Z350XT/21 days), and >CPC (Z350XT/14 days). In mouthrinses-intragroups, VHN of PNHT and Z350XT decreased at 14 days (CHX, CPC) and was maintained over time in NCR (CHX + CPC). VHN-TEC was similar among groups.

Conclusion

Microhardness showed differences due to the interaction of the type of NCR, the composition of the mouthrinses, and time. VHN decreased after 14 days and was more affected in composite resins with lower filler content and in mouthrinses with a lower pH.

The Depth of Cure, Sorption and Solubility of Dual-Cured Bulk-Fill Restorative Materials

This study aimed to examine depth of cure (DoC), mass change, water sorption and solubility of dual-cured bulk-fill restorative materials (Surfil One and Activa) in comparison with a light-cured bulk-fill composite (Filtek One Bulk-Fill) and a resin-modified glass ionomer (Fuji II LC). Twenty specimens were prepared of each material using stainless steel molds designed with a slot (8 × 4 × 2 mm) and irradiated for either 20 or 40 s. The Vickers hardness (VHN) was measured at every 0.5 mm to assess the DoC after 24 h of storage at 37 °C. The depth of cure was reported as the depth corresponding to 80% of the maximum Vickers hardness. Disc-shaped specimens were prepared of each material (n = 5) to investigate mass change, sorption and solubility after 4 months of water storage. The data were analyzed using a two-way and one-way analysis of variance (ANOVA) followed by the Tukey post hoc test (p ≤ 0.05). Fuji II LC had the greatest DoC while Activa had the lowest. The two different irradiation times did not demonstrate a significant difference in DoC for all dual-cured materials (p > 0.05). Fuji II LC had the highest sorption while Filtek One showed the lowest. Surefil One and Fuji II LC had a negative solubility. This study concluded that dual-cured materials showed different depth of cure values despite having the same setting reaction. Both materials exhibited a high water sorption, which might jeopardize their dimensional stability and effect their clinical performance.

Plasmonic Effect of Gold-Patchy Silica Nanoparticles on Green Light-Photopolymerizable Dental Resin

A low ratio of polymerization is a major problem in resin-based composites. In this paper, the plasmonic effect of gold-covered silica nanoparticles on the physicochemical and mechanical properties of bisphenol A diglycidyl dimethacrylate (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA) green light-photopolymerizable dental resin was investigated at an intensity of 1.4 mW/cm2 for 40 s. Transmission electron microscopy (TEM) showed silica of about 350 nm covered with 12-15 nm gold nanoparticles (Au NPs) at 100% nominal coverage. Five different concentrations of bare and patchy silica particles were used; in the latter composite, the calculated Au wt% were 0.0052 wt%, 0.0104 wt%, 0.0208 wt%, 0.04160 wt%, and 0.0823 wt%. The plasmon peak of patchy silica-filled nanocomposite overlapped with the absorption of Irgacure 784 photoinitiator and green LED light emission peak. The effect of plasmon-enhanced polymerization achieved with green light illumination was analyzed using diametral tensile strength (DTS), differential scanning calorimetry (DSC), surface plasmon resonance imaging (SPRi), and degree of conversion (DC) based on Raman spectroscopy. The values of the Au NP with 0.0208 wt% was found to be maximum in all the measured data. Based on our result, it can be concluded that the application of patchy silica particles in dental resin can improve the polymerization ratio and the mechanical parameters of the composite.

Effect of inorganic fillers on the light transmission through traditional or flowable resin-matrix composites for restorative dentistry

OBJECTIVES

The aim of this in vitro study was to evaluate the light transmission through five different resin-matrix composites regarding the inorganic filler content.

METHODS

Resin-matrix composite disc-shaped specimens were prepared on glass molds. Three traditional resin-matrix composites contained inorganic fillers at 74, 80, and 89 wt. % while two flowable composites revealed 60 and 62.5 wt. % inorganic fillers. Light transmission through the resin-matrix composites was assessed using a spectrophotometer with an integrated monochromator before and after light curing for 10, 20, or 40s. Elastic modulus and nanohardness were evaluated through nanoindentation's tests, while Vicker's hardness was measured by micro-hardness assessment. Chemical analyses were performed by FTIR and EDS, while microstructural analysis was conducted by optical microscopy and scanning electron microscopy. Data were evaluated using two-way ANOVA and Tukey's test (p < 0.05).

RESULTS

After polymerization, optical transmittance increased for all specimens above 650-nm wavelength irradiation since higher light exposure time leads to increased light transmittance. At 20- or 40-s irradiation, similar light transmittance was recorded for resin composites with 60, 62, 74, or 78-80 wt. % inorganic fillers. The lowest light transmittance was recorded for a resin-matrix composite reinforced with 89 wt. % inorganic fillers. Thus, the size of inorganic fillers ranged from nano- up to micro-scale dimensions and the high content of micro-scale inorganic particles can change the light pathway and decrease the light transmittance through the materials. At 850-nm wavelength, the average ratio between polymerized and non-polymerized specimens increased by 1.6 times for the resin composite with 89 wt. % fillers, while the composites with 60 wt. % fillers revealed an increased ratio by 3.5 times higher than that recorded at 600-nm wavelength. High mean values of elastic modulus, nano-hardness, and micro-hardness were recorded for the resin-matrix composites with the highest inorganic content.

CONCLUSIONS

A high content of inorganic fillers at 89 wt.% decreased the light transmission through resin-matrix composites. However, certain types of fillers do not interfere on the light transmission, maintaining an optimal polymerization and the physical properties of the resin-matrix composites.

CLINICAL SIGNIFICANCE

The type and content of inorganic fillers in the chemical composition of resin-matrix composites do affect their polymerization mode. As a consequence, the clinical performance of resin-matrix composites can be compromised, leading to variable physical properties and degradation.

Effect of Fibres on Physico-Mechanical Properties of Bulk-Fill Resin Composites

OBJECTIVE

To measure the flexural strength (FS) of bulk-fill resin composites and assess their long-term water absorption and solubility properties with and without the inclusion of short glass fibres.

METHODS

One resin composite, everX Flow with fibres, and four commercially available bulk-fill composites without fibres, namely, PALFIQUE, Activa, SDR Plus, and Filtek Bulk Fill One, were tested. Six specimens (2 × 2 × 25 mm) were fabricated for each material and stored in water for 1 day and 30 days to measure the flexural strength using a three-point bending test. To evaluate water absorption and solubility, circular disks measuring 15 × 2 mm (n = 5) were immersed in water for 60 days, and their weights were recorded periodically. After 60 days, the specimens were dried for an additional 21 days to determine solubility.

RESULTS

Flexural strength values ranged from 101.7 to 149.1 MPa. Significant distinctions were observed among the resin composites at the onset of the study (p < 0.05). The highest FS value was identified in everX Flow, while ACT exhibited the lowest (p < 0.05). However, the flexural strength values exhibited a significant decrease with increased storage time (p < 0.05), except for ACT, which demonstrated a noteworthy increase. Concerning water absorption and solubility, ACT displayed the highest absorption, while the range of solubility varied from -0.88 to 5.8 μg/mm3. ACT also had the highest solubility, whereas everX Flow exhibited negative solubility.

SIGNIFICANCE

The addition of short fibres, along with potential differences in matrix composition, enhanced the flexural strength of everX Flow. However, the substantial reduction in flexural strength observed in everX Flow and SDR following exposure to water corroborates the manufacturers' recommendation to apply a conventional resin composite cap on these materials.

Proposition of New Testing Procedure for the Mechanical Properties of Bulk-Fill Materials

This study analysed flexural properties, microhardness, and the degree of conversion (DC) of five bulk-fill composites under clinically relevant conditions (4 mm thick specimens) in comparison to 2 mm specimens according to ISO 4049. Additionally, the effect of rapid polymerisation on 4 mm specimens was evaluated after accelerated aging. DC was measured using Fourier transform infrared spectrometry at 2 and 4 mm thick layers, while flexural properties and Vickers microhardness were tested using 16 × 2 × 2 mm or 16 × 2 × 4 mm specimens. Three polymerisation protocols were used: (I) "ISO": 2 mm thickness, 1000 mW/cm², double-sided; (II) "10 s": 4 mm thickness, 1000 mW/cm², one-sided; and (III) "3 s": 4 mm thickness, 2600 mW/cm², one-sided. Mechanical properties were tested after 1 day, after 10,000 thermocycles, and after 10,000 thermocycles followed by a 7-day immersion in absolute ethanol. The "ISO" protocol produced a higher DC and microhardness of all materials. Elastic modulus was significantly higher for the "ISO" protocol compared to the 4 mm specimens. The differences in flexural strength for all polymerisation protocols were equalised after thermocycling and immersion in absolute ethanol. All tested materials met the ISO 4049 flexural strength requirement (80 MPa) for all polymerisation methods and all aging conditions. Rapid polymerisation achieved nearly optimal properties (ISO), except for elastic modulus, which was significantly reduced in 4 mm samples.

Effects of Dental Bleaching Agents on the Surface Roughness of Dental Restoration Materials

Background and Objectives: This study aimed to evaluate the surface roughness evolution of several finished and polished composites when bleaching materials are applied. The research was conducted on four microhybrid or nanofilled composites that are used in dental restorations. Materials and Methods: For each composite type, 5 samples were selected for control, 5 samples were subjected to the bleaching protocol "office bleach" with 40% hydrogen peroxide, and 5 other samples were subjected to the "home bleach" protocol with 16% carbamide peroxide, resulting in a total number of 60 samples. The surfaces of all the samples were tested for roughness, and the values of the most relevant parameter (Ra), were collected. Comparisons between composites and samples were performed using one-way ANOVA (in Statistical Package for Social Sciences). Results: After the bleaching protocol with 40% hydrogen peroxide gel, it was found that the roughness of the group increased considerably compared to the control group, so the highest roughness was found at GC Gradia direct anterior group, and the lowest value was registered for the 3M ESPE Valux Plus group. Following the bleaching protocol with 16% carbamide peroxide (home bleach), it was noted that the sample surfaces were not as affected. In this case, the lowest roughness was found at 3M ESPE Valux Plus group, and the highest roughness was registered for the GC G-aenial anterior group. Following the interpretation of the results, all four types of dental composites tested showed significant surface roughness differences between the groups subjected to bleaching protocols and those kept as control (p < 0.05). Conclusions: The surfaces of the samples were affected by the bleaching protocols by increasing the roughness compared to the control samples.

Surface hardness and flexural strength of dual-cured bulk-fill restorative materials after solvent storage

BACKGROUND

This study aimed to evaluate the surface hardness (VHN) and biaxial flexural strength (BFS) of dual-cured bulk-fill restorative materials after solvent storage.

METHODS

Two dual-cured bulk-fill composites (Surefil One® and Activa™ Bioactive), a light-cured bulk-fill composite (Filtek One Bulk-Fill) and a resin-modified glass ionomer (Fuji II LC) were investigated. Surefil One and Activa were used in the dual-cure mode, all materials were handled according to manufacturer's instructions. For VHN determination, 12 specimens were prepared from each material and measured after 1 h (baseline), 1 d, 7 d and 30 d of storage in either water or 75% ethanol-water. For BFS test, 120 specimens were prepared (n = 30/material) and stored in water for either 1, 7 or 30 d before testing. Repeated measures MANOVA, two-way and one-way ANOVA followed by the Tukey post hoc test (p ≤ 0.05) were used to analyze the data.

RESULTS

Filtek One had the highest VHN, while Activa had the lowest. All materials exhibited a significant increase in VHN after 1d of storage in water, except for Surefil One. After 30 d of storage, VHN increased significantly in water except for Activa, while ethanol storage caused a significant time-dependent reduction in all tested materials (p ≤ 0.05). Filtek One showed the highest BFS values (p ≤ 0.05). All the materials, except for Fuji II LC, exhibited no significant differences between 1 and 30 d BFS measurements (p > 0.05).

CONCLUSIONS

Dual-cured materials had significantly lower VHN and BFS compared to the light-cured bulk-fill material. The low results of Activa VHN and Surefil One BFS, indicate that these materials should not be recommended in posterior stress-bearing areas.

Effect of monomer composition and filler fraction on surface microhardness and depth of cure of experimental resin composites

This study evaluated microhardness profiles and calculated depths of cure at 80% of the surface microhardness of experimental dental resin composites having different base monomer compositions and different filler fractions. Composites were prepared using four different base monomers (bisphenol A-glycidyl methacrylate [Bis-GMA], urethane dimethacrylate [UDMA], ethoxylated bisphenol-A dimethacrylate [Bis-EMA], and Fit-852) with triethylene glycol dimethacrylate (TEGDMA) used as a co-monomer at three filler:resin matrix weight percent fractions (50:50, 60:40, and 70:30). Uncured material was placed in 3D printed molds and light cured for 40 s from the top surface only. Knoop microhardness was measured at the top of the specimen, and at every 0.5 mm up to 4 mm in depth. Microhardness at the surface increased in all experimental composites as the filler fraction increased. When comparing base monomers, microhardness was the highest in UDMA-based composites, while Bis-GMA-based composites showed the lowest values. When comparing depth of cure as a function of base monomer type, both Bis-GMA and Bis-EMA showed significantly lower values than UDMA or Fit-852. Composites having 50 wt% filler showed a significantly higher depth of cure than those with 60 and 70 wt% filler. Base monomer and filler fraction significantly influence microhardness and depth of cure in these experimental composites.

In Silico Finite Element Analysis of Implant-Supported CAD-CAM Resin Composite Crowns

PURPOSE

The aim of this study was to evaluate the mechanical behavior of an implant-supported crown made using computer-aided design and computer-aided manufacturing (CAD-CAM) resin composite (RC) blocks in the posterior region.

MATERIAL AND METHODS

Four commercially available CAD-CAM RC blocks were used in this study: Cerasmart 300 (CS300; GC, Tokyo, Japan), Katana Avencia P Block (KAP; Kuraray Noritake Dental, Niigata, Japan); KZR HR3 Gamma Theta (HR3; Yamakin, Osaka, Japan), and Estelite P block (ESP; Tokuyama Dental, Tokyo, Japan). Katana Zirconia STML (ST; Kuraray Noritake Dental) was used as the control group. The elastic moduli of each material were determined by a three-point bending test. After the CAD models were designed, two different loading scenarios (oblique, vertical) were created. 3D finite element analysis was conducted with the prepared models.

RESULTS

The elastic modulus of the material utilized for the implant restorations did not cause any change in the stresses transmitted to the implant or peripheral bone. An important difference was detected in the abutment-crown junction area. The minimum von Mises value at the abutment-crown interface was obtained in ST, which has the closest elastic modulus to the titanium abutment.

CONCLUSIONS

The 3D finite element model designed in this study was used to demonstrate that implant-supported crowns fabricated with four different CAD-CAM RCs showed no critical stress concentrations in the bone or implant under all loading conditions. These results suggest that CAD-CAM RC blocks could be used as an alternative material for implant-supported restorations in the posterior region in terms of stress distribution.

3D Printing of CNT- and YSZ-Added Dental Resin-Based Composites by Digital Light Processing and Their Mechanical Properties

This study demonstrates the successful 3D printing of dental resin-based composites (DRCs) containing ceramic particles using the digital light processing (DLP) technique. The mechanical properties and oral rinsing stability of the printed composites were evaluated. DRCs have been extensively studied for restorative and prosthetic dentistry due to their clinical performance and aesthetic quality. They are often subjected to periodic environmental stress, and thus can easily undergo undesirable premature failure. Here, we investigated the effects of two different high-strength and biocompatible ceramic additives, carbon nanotube (CNT) and yttria-stabilized zirconia (YSZ), on the mechanical properties and oral rinsing stabilities of DRCs. Dental resin matrices containing different wt.% of CNT or YSZ were printed using the DLP technique after analyzing the rheological behavior of slurries. Mechanical properties such as Rockwell hardness and flexural strength, as well as the oral rinsing stability of the 3D-printed composites, were systematically investigated. The results indicated that a DRC with 0.5 wt.% YSZ exhibits the highest hardness of 19.8 ± 0.6 HRB and a flexural strength flexural strength of 50.6 ± 6 MPa, as well as reasonable oral rinsing steadiness. This study provides a fundamental perspective for designing advanced dental materials containing biocompatible ceramic particles.

Can Modification with Urethane Derivatives or the Addition of an Anti-Hydrolysis Agent Influence the Hydrolytic Stability of Resin Dental Composite?

Due to the questionable durability of dental restorations, there is a need to increase the lifetime of composite restoration. The present study used diethylene glycol monomethacrylate/4,4'-methylenebis(cyclohexyl isocyanate) (DEGMMA/CHMDI), diethylene glycol monomethacrylate/isophorone diisocyanate (DEGMMA/IPDI) monomers, and bis(2,6-diisopropylphenyl)carbodiimide (CHINOX SA-1) as modifiers of a polymer matrix (40 wt% urethane dimethacrylate (UDMA), 40 wt% bisphenol A ethoxylateddimethacrylate (bis-EMA), and 20 wt% triethyleneglycol dimethacrylate (TEGDMA)). Flexural strength (FS), diametral tensile strength (DTS), hardness (HV), sorption, and solubility were determined. To assess hydrolytic stability, the materials were tested before and after two aging methods (I-7500 cycles, 5 °C and 55 °C, water and 7 days, 60 °C, 0.1 M NaOH; II-5 days, 55 °C, water and 7 days, 60 °C, 0.1 M NaOH). The aging protocol resulted in no noticeable change (median values were the same as or higher than the control value) or a decrease in the DTS value from 4 to 28%, and a decrease in the FS value by 2 to 14%. The hardness values after aging were more than 60% lower than those of the controls. The used additives did not improve the initial (control) properties of the composite material. The addition of CHINOX SA-1 improved the hydrolytic stability of composites based on UDMA/bis-EMA/TEGDMA monomers, which could potentially extend the service life of the modified material. Extended studies are needed to confirm the possible use of CHINOX SA-1 as an antihydrolysis agent in dental composites.

Synthesis of Submicrometric Chitosan Particles Loaded with Calcium Phosphate for Biomedical Applications

Chitosan particles loaded with dibasic calcium phosphate anhydrous (DCPA) is a promising strategy for combining antimicrobial and osteoconduction properties in regenerative medicine. However, mostly micrometer-sized particles have been reported in the literature, limiting their use and reducing their effect in the biomedical field. We have recently overcome this limitation by developing submicrometer-sized particles with electrospray technique. The objective of this study was to understand how the process parameters control the size and properties of submicrometer chitosan particles loaded with DCPA. Solutions of 10 mg/mL chitosan and 2.5 mg/mL DCPA in a 90% acetic acid were electrosprayed under three distinct flow rate conditions: 0.2, 0.5, and 1.0 mL/h. The particles were crosslinked in a glutaraldehyde atmosphere and characterized in terms of their morphology, inorganic content, zeta potential, and minimum inhibitory concentration (MIC) against S. mutans. All conditions showed particles with two similar morphologies: one small-sized with a spherical shape and another larger-sized with a bi-concave shape. All generated a broad particle size distribution, with a similar mean size of ~ 235 nm. The addition of DCPA decreased the zeta potential for all the samples, but it was above 30 mV, indicating a low aggregation potential. The lower flow rate showed the worst efficacy for DCPA incorporation. Antimicrobial activity was greater in chitosan/DCPA particles with flow rate of 0.5 mL/h. It can be concluded that the flow rate of 0.5 mL/h presents the best compromise solution in terms of morphology, zeta potential, MIC, and inorganic content.

Effect of shelf-storage temperature on degree of conversion and microhardness of composite restorative materials

BACKGROUND

The pre-cure temperature is considered an important parameter that affects the polymerization kinetics and the properties of composite restoration. As dissension exists about the effect of storing composite restorative materials in refrigerator, this study aimed to assess the effect of shelf-storage temperature on degree of conversion (DC) and microhardness of three composite restorative materials with different matrix systems.

METHODS

Three commercially-available composite restorative materials were used in this study; an Ormocer-based composite (Admira Fusion, Voco GmbH), a nanoceramic composite, (Ceram.X SphereTEC One, Dentsply Sirona GmbH), and a nanohybrid composite (Tetric N-Ceram, Ivoclar Vivadent AG). Regarding DC and microhardness tests, 60 disc-shaped composite specimens for each test were randomly divided into 3 groups (n = 20) according to the restorative material used. Each group was divided into 2 subgroups (n = 10) according to the composite storage temperature; stored at room temperature or stored in the refrigerator at 4°-5 °C. DC was evaluated using a Fourier-transform infrared spectrometer coupled to an attenuated total reflectance accessory. Microhardness was evaluated using micro-Vickers hardness tester under a load of 50 g with a dwell time of 10 s. The results were analyzed by ANOVA, post-hoc LSD, and independent t-tests at a significance level of p < 0.05.

RESULTS

Regarding DC test all groups showed statistically significant differences at both storage temperature. The Ormocer-based composite had the highest mean values. There was a statistically significant difference between all room-stored groups and their corresponding groups stored at refrigerator (p < 0.05). For microhardness test, all groups exhibited also statistically significant differences at both storage temperatures with the Ormocer-based composite having the highest mean values. A statistically significant difference between both room-stored and refrigerator-stored groups has been observed also (p < 0.05).

CONCLUSIONS

Refrigeration of resin-composite might have a deleterious effect on DC and microhardness of the tested composite restorative materials with different matrix systems. Moreover, the differences in the formulations of composite matrix have a potential impact on DC and microhardness.

Quasi-static indentation damage mechanics of PU foam core reinforced with fly ash particulate

The fly ash (FA) particulates are used in this study to reinforce the polyurethane foam (PUF) core. The FA particles inclusion improves the mechanical performance of the PUF core under compression by increasing its modulus of elasticity. Low-velocity impacts have damage dynamics that are pretty similar to quasi-static indentation. Consequently, the indentation resistance capability of the PUF core is investigated for three types of indenter nose tips with varied FA wt. Percentages (flat-circular, hemispherical, and conical). The results reveal that the reinforced foam core’s resistance varies with reinforcement percentage under indentation. However, FA reinforcement to PUF does not necessarily improve indentation resistance. The damage mechanism of the PUF core under indentation has been evaluated for each type of indenter. The interaction of crushing, shear, and tear of the damaged surface with the change in indenter nose tip has been explained with 0–20% variation of FA particles. Scanning electron microscope (SEM) images are taken for the analysis of the damaged PUF core cross-section at the indented location. Earlier mechanical findings of the scatter in deformation behavior with the indenter nose tip geometry are substantiated by the SEM studies.

Influence of filler types on wear and surface hardness of composite resin restorations

OBJECTIVE

Wear and surface hardness of resin composites are of relevance from the clinical standpoint. With the incorporation of novel filler system, more studies need to be performed to investigate newly marketed resin composites. The objective of this study was to investigate the abrasive wear and surface hardness of dental restorative with different filler types.

METHODS

Nanohybrid filled Harmonize (HM) and Tetric N-Ceram (TNC), microhybrid filled Filtek Z250 (Z250), nanofilled Filtek Z350 (Z350) were included in the study. Twelve cylindrical resin composites specimens with 10 mm in diameter and 6 mm in thickness were prepared for abrasive wear test. Eight hundred cycles under 17 kg load were conducted for final wear by CW3-1 wear machine. The specimen was cleaned with an ultrasonic unit for 3 min followed with drying procedure. After measurement of weight loss and the density of specimens, the specimens were kept for measurement of surface hardness. Surface hardness was measured using a micro-hardness tester with a Vickers diamond indenter after polishing. Three specimens of each material were observed by scanning electron microscopy (SEM) after the abrasion to evaluate the morphology of the surface. Data were analyzed using one-way analysis of variance (ANOVA), followed by Tukey HSD test (α = .05).

RESULTS

Z250 performed the least volume wear loss (41.1 ± 2.1 mm3), as well as the hardest value (102.7 ± 2.9 HV). There was no significant difference with the volume wear loss (p = 1.000) and surface hardness (p = 0.874) of HM and TNC. SEM images of nanohybrid filled HM and TNC represented smoother surface compared with other types of resin composites.

CONCLUSIONS

Microhybrid Z250 showed the highest wear resistance and surface hardness, nanofilled and nanohybrid resin composites may still face the insufficient of wear and surface hardness quality.

Tests of Dental Properties of Composite Materials Containing Nanohybrid Filler

Complex composite materials are used in many areas of dentistry. Initially, chemically hardened materials were also used, and in this group nanohybrid composites are highly valued. They are often used today, mainly for the direct reconstruction of damaged hard tooth tissue materials for rebuilding damaged tissues using indirect adhesive techniques. The research was conducted to determine the mechanical properties of materials with nanofillers. The article focuses on methods of important test methods for dental prosthetics: resilience, abrasion, wear test, impact strength, hardness, SEM, and chemical analysis. As part of this work, five different series of hybrid composites with nano-fillers were tested. The mechanical properties of composites, such as compressive strength, microhardness, flexural strength, and modulus of elasticity, depend mainly on the type, particle size, and amount of filler introduced. The obtained test results showed that the type and amount of nanofiller have a significant influence on the mechanical and tribological properties. The introduction of nanofillers allowed us to obtain higher mechanical properties compared to classic materials discussed by other researchers. The study observed a change in vibrations in the IR spectrum, which allowed a comparison of the organic structures of the studied preparations.

Microbiological models for accelerated development of secondary caries in vitro

OBJECTIVES

The current study aimed to compare the efficacy of two in vitro microbiological models based on open and closed systems designed to obtain secondary caries in an accelerated and reproducible way.

METHODS

A conventional resin-based composite (RBC - Majesty ES-2; Kuraray, Japan) and a resin-modified glass-ionomer cement (RMGIC - Ionolux; VOCO, Germany) were used to restore standardized class II cavities (n = 4/tooth, cervical margin in dentin) in 16 human molars. The ability to produce secondary caries with Streptococcus mutans biofilms was tested using either an open-cycle or closed-cycle bioreactor (n = 8 specimens/model). Specimens were scanned before and after the biofilm exposure using micro-CT (Skyscan 1176, 9 µm resolution, 80 kV, 300 mA). Image reconstruction was performed, and demineralization depths (µm) were evaluated at the restoration margins and a distance of 1.0 mm.

RESULTS

Dentin demineralization could be observed in all specimens, and enamel demineralization in 50% of the specimens. The open system bioreactor produced lesions with significantly higher overall demineralization depths (p < .001). However, demineralization depths at a 1.0 mm distance from the restoration margins showed no difference between open and closed systems or materials. In the open system, significantly lower demineralization depths were observed in proximity to RMGIC than RBC (p < .001), which was not significantly different in the closed system (p = .382).

CONCLUSIONS

Both systems produced in vitro secondary caries in an accelerated way. However, the open-cycle bioreactor system confirmed the caries-protective activity exerted by the RMGIC material in contrast to the RBC, better simulating materials' clinical behavior.

CLINICAL SIGNIFICANCE

The possibility of obtaining accelerated and reproducible secondary caries development in vitro is fundamental in testing the behavior of conventional and yet-to-come restorative dental materials. Such systems can provide faster outcomes regarding the performance of dental restorative materials compared to clinical studies, notwithstanding the importance of the latter.

Development of functional fillers as a self-healing system for dental resin composite

OBJECTIVES

To evaluate the incorporation of repairing capsules containing different monomers and polymerization modulators on the self-healing efficiency of an experimental photopolymerizable resin-based composite.

METHODS

Self-healing capsules containing different monomers and polymerization modulators were prepared by emulsion polymerization: TC_DHEPT (TEGDMA and DHEPT), BTC_DHEPT (Bis-GMA, TEGDMA, and DHEPT), and BTC_BPO (Bis-GMA, TEGDMA, and BPO). The capsules were analyzed through Fourier transform infrared spectroscopy and scanning electron microscopy. The capsules were added into experimental photopolymerizable resin composites establishing the following groups: ER (Control without capsules), ER+BPO, ER+BPO+TC_DHEPT, and ER+BTC_BPO+BTC_DHEPT. Filtek Z350 resin composite (3 M ESPE) was used as a commercial reference. The materials were tested for degree of conversion (DC), flexural strength (σf), elastic modulus (Ef), fracture toughness (virgin K_IC), self-healing efficiency (healed K_IC), and roughness. For statistical analysis, the significance value was established at an a = 0.05 level.

RESULTS

When compared to the control material, the incorporation of repairing capsules did not affect DC, σf, and Ef. Fracture toughness was statistically similar between the experimental groups (p ≤ 0.05). Healed K_IC was statistically different between the groups ER+TC_DHEP and ER+BTC_BPO+BTC_DHEPT; the self-healing efficiency was higher for ER+TC_DHEPT. Surface roughness was statistically similar among all groups.

CONCLUSIONS

The use of self-healing capsules promoted repair of the material. Studies with material aging after the self-healing process are necessary to better demonstrate the effectiveness of this system.

CLINICAL SIGNIFICANCE

The self-healing system seemed to be a promising technology to be used in self-repaired restorative materials, which may prevent restoration fractures.

Assessment of Micro-Hardness, Degree of Conversion, and Flexural Strength for Single-Shade Universal Resin Composites

Single-shade universal resin composites (SsURC) are preferred in clinical practice to reduce time for shade selection and obtain good esthetic results. In this study, the static mechanical properties of seven new SsURCs were investigated, their spectral analyzes were performed and scanning electron microscopy (SEM) evaluations were presented. Charisma Diamond One/DO, Admira Fusion x-tra/AFX, Omnichroma/OC, OptiShade/OS, Essentia Universal/EU, Zenchroma/ZC, Vittra APS Unique/VU were used in a three-point bending test to determine flexural strength (FS) and elastic modulus (EM); Vickers micro-hardness (VHN) and hardness-ratio (HR) were performed with a micro-hardness tester from top/bottom after 24-h/15-days of storage in distilled water at 37 °C (±1 °C). The degree of conversion (DC) was assessed by using Fourier transform infrared spectroscopy (FTIR). The structure of the resin matrix and filler content were assessed by SEM. Data were analyzed using IBM SPSS V23 and the R program and the significance level was taken as p < 0.05. The main effect of the tested SsURCs was found to be statistically significant on FS, EM, VHN, and DC values (p < 0.001). Bis-GMA free SsURCs (AFX, DO, VU) showed better DC and HR except for OC. All seven tested SsURCs conform to the requirements of ISO standards for dental resin composites for all tested categories.

TEGDMA-Functionalized Dicalcium Phosphate Dihydrate Resin-Based Composites Prevent Secondary Caries in an In Vitro Biofilm Model

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries, SC). Standardized Class-II cavities were made in sound molars with the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a bisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass and 20 wt.% T-DCPD (RBC-20); or 20 wt.% Ba glass and 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced Streptococcus mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning electron microscopy and energy-dispersive X-ray spectroscopy characterized the specimen surfaces, and antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey’s tests were applied at p < 0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p < 0.0001). Initial enamel demineralization could be observed only around the RBC-0 and RBC-20 restorations. Direct antibiofilm activity can explain SC reduction by RMGIC, whereas a buffering effect on the acidogenicity of biofilm can explain the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

Bulk-fill restorative composites under simulated carious and erosive conditions

Acidic conditions can cause hydrolysis and accelerate degradation of resin composites (RCs). Since there are limited and controversial data on the effect of acids on bulk-fill RCs, this study assessed the surface roughness (SR) and flexural strength (FS) of these RCs under simulated carious and erosion conditions. Bars of Filtek Bulk Fill (FBF, 3M/ESPE), X-tra fil (XTF, Voco), Tetric N-Ceram Bulk Fill (TBF, Ivoclar/Vivadent), and Aura Bulk Fill (ABF, SDI) and a conventional RC [Filtek Z350XT (FZ, 3M/ESPE)] were allocated (n=15) to undergo caries or erosion conditions. The control group was kept in artificial saliva (AS). The bars were evaluated for SR change (final-baseline) and for three-point FS. Data were analyzed using ANOVA and Tukey's test. At the baseline (p <0.001), the SR of RCs ranked as follows: (TBF = XTF) < FBF (none differed from FZ) < ABF. The interplay between RCs and conditions affected SR change (p = 0.025). While after storage in AS, there was no difference among RCs, following carious and erosive conditions, ABF showed higher SR change. For FS (p <0.001), XTF > (FBF = FZ) > (TBF = FZ) > ABF, with no difference among control, carious and erosive conditions (p = 0.148). Depending on the restorative bulk-fill RCs, carious and erosive conditions roughen the surface but do not affect the FS of these materials.

Color stability and surface roughness of ormocer- versus methacrylate-based single shade composite in anterior restoration

Background

The blending ability of universal shade composites and their stability in the oral environment are of great concern in restoring anterior teeth. This study aims to evaluate and compare the color stability and surface roughness of two single-shade composite restorations, ormocer-based composite (OBC) and methacrylate resin-based composite (RBC), after storing them in different staining media.

Materials and methods

In this study, two universal shade composite restorative materials were tested: a nanohybrid OBC (Admira fusion X-tra, Voco) and a supra-nanofilled RBC (Omnichroma, Toukyama). In total, 60 cylindrical centralized cavities (diameter: 5 mm, depth: 2 mm) were prepared in sound extracted-human central incisors and divided into two equal groups according to the restorative material used (n = 30). According to the storage media, the teeth of each group were divided into three subgroups (n = 10): artificial saliva, black tea, and cola. The restoration color was evaluated for all teeth at baseline and after four weeks of storage. The color stability (∆E) was measured using a reflective spectrophotometer (X-Rite, model RM200QC, Neu-Isenburg, Germany). The surface roughness (Ra) was evaluated using three-dimensional optical profilometry (Wyko, Model NT 1100, Veeco, Tucson, USA). Additionally, the extracted data were analyzed using two-way analysis of variance (ANOVA), one-way ANOVA and Student’s t-test.

Results

In the baseline evaluation, there were no statistically significant differences with respect to color matching or surface roughness results between the two studied restorative materials. However, the differences were statistically significant after storing them in different media.

Conclusion

Universal composites showed satisfactory color matching with different teeth colors and accepted surface smoothness, whereas the aging procedure exerted a negative effect on their color stability and surface characteristics.

Martens Hardness of CAD/CAM Resin-Based Composites

(1) Background: The properties of CAD/CAM resin-based composites differ due to differences in their composition. Instrumented indentation testing can help to analyze these differences with respect to hardness, as well as energy-converting capabilities due to viscoelastic behavior. (2) Methods: Eleven materials were investigated using instrumented indentation testing. Indentation depth (hr), Martens hardness (HM), indentation hardness (HIT), indentation modulus (EIT), the elastic part of indentation work (ηIT), and indentation creep (CIT) were investigated, and statistical analysis was performed using one-way ANOVA, Bonferroni post-hoc test, and Pearson correlation (α = 0.05). (3) Results: All of the investigated parameters revealed differences between the analyzed materials. Besides the differences in hardness-associated parameters (hr, HM, and HIT), instrumented indentation testing demonstrated differences in energy-converting properties. The subsequent one-way ANOVA revealed significant differences (p < 0.001). A significant (p < 0.01, Pearson correlation >0.576) correlation between the materials and HM, HIT, or EIT was identified. (4) Conclusions: Due to the differences found in the energy-converting properties of the investigated materials, certain CAD/CAM resin-based composites could show superior stress-breaking capabilities than others. The consequential reduction in stress build-up may prove to beneficial, especially for implant-retained restorations or patients suffering from parafunctions.

Effects of the crosslinking of chitosan/DCPA particles in the antimicrobial and mechanical properties of dental restorative composites

The development of restorative materials containing antibacterial agents is an alternative to reduce the progression of caries lesions.

OBJECTIVE

to compare the influence of the degree of crosslinking of chitosan particles loaded with dibasic calcium phosphate (DCPA) on the mechanical properties, degree of conversion (DC), and antimicrobial properties of experimental composites.

METHODS

Chitosan/DCPA particles were synthesized by the electrospraying, crosslinked by 0, 8, or 16 h in glutaraldehyde, and characterized by zeta potential and minimum inhibitory concentration (MIC) against S. mutans. Experimental resin composites of Bis-GMA and TEGDMA and 59.5% of barium glass were synthesized, chitosan/DCPA particles were added at 0 or 0.5 wt% with the different crosslinking time. The materials were subject to DC analysis, three-point bending test at 24 h and 7 days, and antimicrobial assays. Data were submitted to one-way ANOVA and Tukey test (α = 0.05).

RESULTS

The particles with longer crosslinking time presented higher zeta potential and MIC, and the composite containing these particles showed significantly higher biofilm inhibition than the control group. The other two groups were similar to each other and the control. The composite containing particles with 88 h crosslinking time showed the lowest flexural strength at 7 days in water, and materials with non-crosslinked particles and longer crosslinking time presented flexural strength similar to control. The flexural modulus and DC showed no statistical difference among groups.

SIGNIFICANCE

composite resin containing 0.5% chitosan/DCPA particles crosslinked by 16 h showed a reduction of biofilm formation without affecting the mechanical properties in relation to the control.

Influence of silane coupling agent on the mechanical performance of flowable fibre-reinforced dental composites

OBJECTIVES

This experimental investigation explored the optimisation of silane treatment of surface-modified S-2 Glass fibres in restorative dental composites for improved mechanical performance. The influence of optimum amount of silane to improve the interfacial adhesion at the fibre-matrix interfaces and its effect on the mechanical properties of the restorative composites were explored.

METHODS

S-2 Glass fibres of 5 μm diameter and 250 μm length were surface modified using the acid etching technique. The etched fibres were then treated with either 3-methacryloxypropyltrimethoxysilane (3-MPS), 3-Glycidoxipropyltrimethoxysilane (3-GPS) or 8-methacryloxyoctyltrimethoxysilane (8-MOTS) at varying molar % / wt% concentrations. Fibres that were not silanised with any silane coupling agents were used as the control sample. The silanol content of each mixed silane was observed using Fourier transform infrared (FT-IR) spectroscopy analysis. Fibres (5 wt%) with optimised molar% / wt% silane coupling concentration were added to UDMA/TEGDMA dental resin. Mechanical properties such as flexural strength, flexural modulus, and the breaking energy of the materials were evaluated using a comprehensive experimental programme.

RESULTS

FTIR spectrum of glass fibre silanised with each silane coupling agent revealed many peaks from 3800 to 1400 cm^-1, indicative of -CH₃, -CH_2, and CO bonding, suggesting the proper silanization of the fibre. The contact angle test revealed that optimum wt% concentration of 3-MPS, 3-GPS and 8-MOTS were 0.5%, 0.8% and 1.4% respectively. The flexural strength of the fibre-reinforced with optimum concentration of 3-MPS (DC-3-MPS_0.5%) increased by 7.0% compared to those of the 2 wt% concentration of 3-MPS fibre-reinforced composite (DC-3-MPS_2.0%). While the flexural strength of optimum concentration 8-MOTS grafted dental resin composites (DC-8-MOTS_1.4%) were 9.9% higher than that of 2 wt% concentration 8-MOTS grafted dental resin composite (DC-8-MOTS_2.0%) and the flexural strength of optimum concentration of 3-GPS (DC-3-GPS_0.8%) was 7.5% higher when compared to that of 2 wt% concentration 3-GPS grafted dental resin composites (DC-3-GPS_2.0%). A concurrent trend was found while investigating the fracture behaviour of the dental composite with optimum wt% concentration of each silane coupling agent against its corresponding higher wt% concentrations. The ANOVA results showed that the optimum fibre-reinforced dental composites grafted with 8-MOTS showed better mechanical behaviour when compared to 3-GPS and 3-MPS.

SIGNIFICANCE

The interfacial adhesion between the fibre and the resin due to silane coupling agents has helped to improve the mechanical properties of the fibre-reinforced dental composite. This is the first experimental study to provide a thorough investigation into the significance of the optimal use of silane coupling agents to treat the S-2 Glass fibres and subsequently the influence on the mechanical performance of the fibre-reinforced flowable dental composites.

Developments in resin-based composites

With the phasing down of dental amalgam use in response to the Minamata Convention, it is likely that resin-based composite restoratives will be the dental material of choice for the direct restoration of compromised dentition in the UK, at least for the foreseeable future. The current materials have a finite lifespan, with failures predominately due to either secondary caries or fracture. Consequently, there is considerable in vitro research reported each year with the intention of producing improved materials. This review describes the recent research in materials designed to have low polymerisation shrinkage and increased mechanical properties. Also described is research into materials that are either antimicrobial or are designed to release ions into the surrounding oral environment, with the aim of stimulating remineralisation of the surrounding dental tissues. It is hoped that by describing this recent research, clinicians will be able to gain some understanding of the current research that will potentially lead to new products that they can use to improve patient treatment in the future.

Provides an overview of recent research developments aimed at improving the performance of resin-based composites.

Details the recent developments in monomers and fillers to produce resin-based composites that either have lower polymerisation shrinkage or better mechanical properties compared to current commercially available products.

Describes recent research on developing resin-based composites that can act as potential sources of antimicrobial or remineralising agents.

The Influence of Low-Molecular-Weight Monomers (TEGDMA, HDDMA, HEMA) on the Properties of Selected Matrices and Composites Based on Bis-GMA and UDMA

Bisphenol A-glycidyl methacrylate (bis-GMA) and urethane dimethacrylate (UDMA) are usually combined with low-viscosity monomers to obtain more desirable viscosity, handling characteristics and general properties. The present study determined the flexural strength (FS), flexural modulus (FM), diametral tensile strength (DTS), and hardness (HV) of five matrices and composites based on these resins. The polymerization shrinkage stress (PSS) was also studied for the composites. The polymer matrices were formed using bis-GMA and UDMA. TEGDMA, HEMA and HDDMA acted as co-monomers. The composites had 45 wt.% of filler content. The highest FS and FM were obtained from the UDMA/bis-GMA/TEGDMA/HEMA matrix and the composite (matrix + filler). The best DTS values were obtained from the UDMA/bis-GMA/HEMA matrix and the composite. One of the lowest values of FS, FM, and DTS was obtained from the UDMA/bis-GMA/HDDMA matrix and the composite. All the composites demonstrated similar hardness values. The lowest polymerization shrinkage stress was observed for the UDMA/bis-GMA/TEGDMA/HEMA composite, and the highest PSS was observed for the UDMA/bis-GMA/TEGDMA/HDDMA composite. The addition of HEMA had a positive effect on the properties of the tested materials, which may be related to the improved mobility of the bis-GMA and UDMA monomers.