Daptomycin-loaded biodegradable thermosensitive hydrogels enhance drug stability and foster bactericidal activity against Staphylococcus aureus

Anionic polysaccharides for stabilization and sustained release of antimicrobial peptides

Chemical and enzymatic in vivo degradation of antimicrobial peptides represents a major challenge for their therapeutic use to treat bacterial infections. In this work, anionic polysaccharides were investigated for their ability to increase the chemical stability and achieve sustained release of such peptides. The investigated formulations comprised a combination of antimicrobial peptides (vancomycin (VAN) and daptomycin (DAP)) and anionic polysaccharides (xanthan gum (XA), hyaluronic acid (HA), propylene glycol alginate (PGA) and alginic acid (ALG)). VAN dissolved in buffer of pH 7.4 and incubated at 37 °C showed first order degradation kinetics with a reaction rate constant k_obs of 5.5 × 10^-2 day^-1 corresponding with a half-life of 13.9 days. However, once VAN was present in a XA, HA or PGA-based hydrogel, k_obs decreased to (2.1-2.3) × 10^-2 day^-1 while k_obs was not affected in an alginate hydrogel and a dextran solution (5.4 × 10^-2 and 4.4 × 10^-2 day^-1). Under the same conditions, XA and PGA also effectively decreased k_obs for DAP (5.6 × 10^-2 day^-1), whereas ALG had no effect and HA even increased the degradation rate. These results demonstrate that the investigated polysaccharides (except ALG for both peptides and HA for DAP) slowed down the degradation of VAN and DAP. DSC analysis was used to investigate on polysaccharide ability to bind water molecules. Rheological analysis highlighted that the polysaccharides containing VAN displayed an increase in G' of their formulations, pointing that the peptides interaction act as crosslinker of the polymer chains. The obtained results suggest that the mechanism of stabilization of VAN and DAP against hydrolytic degradation is conferred by electrostatic interactions between the ionizable amine groups of the drugs and the anionic carboxylate groups of the polysaccharides. This, in turn, results in a close proximity of the drugs to the polysaccharide chain, where the water molecules have a lower mobility and, therefore, a lower thermodynamic activity.

Thermosensitive In Situ Gels for Joint Disorders: Pharmaceutical Considerations in Intra-Articular Delivery

The intra-articular administration of conventional drug solutions or dispersions in joint diseases such as osteoarthritis has a relatively short retention time and, therefore, limited therapeutic effect. Thermosensitive polymer solutions that exhibit a sol-gel phase transition near body temperature after injection can prolong drug retention by providing a depot from which the drug release is sustained while relieving inflammation and preventing degradation of the joint complex. Thermosensitive hydrogels have in recent times garnered considerable attention in the intra-articular therapeutics of joint diseases such as osteoarthritis. Among the stimuli-responsive gelling systems, most research has focused on thermosensitive hydrogels. These gels are preferred over other stimuli-sensitive hydrogels since they have well-controlled in situ gelling properties and are also easier to load with drugs. Temperature-sensitive polymers, such as block copolymers or poloxamers, are frequently used to modify their gelation properties, usually in combination with other polymers. They are compatible with most drugs but may pose formulation challenges in terms of their low-response time, highly fragile nature, and low biocompatibility. The stability and biodegradability of implant hydrogels can control the drug release rate and treatment efficacy. This review stresses the application of thermosensitive gels in joint disorders and summarizes recent developments for intra-articular application, including the incorporation of nanoparticles. The hydrogel composition, drug release mechanisms, and the challenges involved in their formulation and storage are also discussed.

Polymyxin and lipopeptide antibiotics: membrane-targeting drugs of last resort

The polymyxin and lipopeptide classes of antibiotics are membrane-targeting drugs of last resort used to treat infections caused by multi-drug-resistant pathogens. Despite similar structures, these two antibiotic classes have distinct modes of action and clinical uses. The polymyxins target lipopolysaccharide in the membranes of most Gram-negative species and are often used to treat infections caused by carbapenem-resistant species such as Escherichia coli, Acinetobacter baumannii and Pseudomonas aeruginosa. By contrast, the lipopeptide daptomycin requires membrane phosphatidylglycerol for activity and is only used to treat infections caused by drug-resistant Gram-positive bacteria such as methicillin-resistant Staphylococcus aureus and vancomycin-resistant enterococci. However, despite having distinct targets, both antibiotic classes cause membrane disruption, are potently bactericidal in vitro and share similarities in resistance mechanisms. Furthermore, there are concerns about the efficacy of these antibiotics, and there is increasing interest in using both polymyxins and daptomycin in combination therapies to improve patient outcomes. In this review article, we will explore what is known about these distinct but structurally similar classes of antibiotics, discuss recent advances in the field and highlight remaining gaps in our knowledge.

Inherent and Composite Hydrogels as Promising Materials to Limit Antimicrobial Resistance

Antibiotic resistance has increased significantly in the recent years, and has become a global problem for human health and the environment. As a result, several technologies for the controlling of health-care associated infections have been developed over the years. Thus, the most recent findings in hydrogel fabrication, particularly antimicrobial hydrogels, could offer valuable solutions for these biomedical challenges. In this review, we discuss the most promising strategies in the development of antimicrobial hydrogels and the application of hydrogels in the treatment of microbial infections. The latest advances in the development of inherently and composite antimicrobial hydrogels will be discussed, as well as hydrogels as carriers of antimicrobials, with a focus on antibiotics, metal nanoparticles, antimicrobial peptides, and biological extracts. The emergence of CRISR-Cas9 technology for removing the antimicrobial resistance has led the necessity of new and performant carriers for delivery of the CRISPR-Cas9 system. Different delivery systems, such as composite hydrogels and many types of nanoparticles, attracted a great deal of attention and will be also discussed in this review.

Advancements in release-active antimicrobial biomaterials: A journey from release to relief

Escalating medical expenses due to infectious diseases are causing huge socioeconomic pressure on mankind globally. The emergence of antibiotic resistance has further aggravated this problem. Drug-resistant pathogens are also capable of forming thick biofilms on biotic and abiotic surfaces to thrive in a harsh environment. To address these clinical problems, various strategies including antibacterial agent delivering matrices and bactericidal coatings strategies have been developed. In this review, we have discussed various types of polymeric vehicles such as hydrogels, sponges/cryogels, microgels, nanogels, and meshes, which are commonly used to deliver antibiotics, metal nanoparticles, and biocides. Compositions of these polymeric matrices have been elaborately depicted by elucidating their chemical interactions and potential activity have been discussed. On the other hand, various implant/device-surface coating strategies which exploit the release-active mechanism of bacterial killing are discussed in elaboration. This article is categorized under: Therapeutic Approaches and Drug Discovery > Nanomedicine for Cardiovascular Disease Implantable Materials and Surgical Technologies > Nanomaterials and Implants Therapeutic Approaches and Drug Discovery > Nanomedicine for Infectious Disease.

Toward Designing of Anti-infective Hydrogels for Orthopedic Implants: From Lab to Clinic

An alarming increase in implant failure incidence due to microbial colonization on the administered orthopedic implants has become a horrifying threat to replacement surgeries and related health concerns. In essence, microbial adhesion and its subsequent biofilm formation, antibiotic resistance, and the host immune system's deficiency are the main culprits. An advanced class of biomaterials termed anti-infective hydrogel implant coatings are evolving to subdue these complications. On this account, this review provides an insight into the significance of anti-infective hydrogels for preventing orthopedic implant associated infections to improve the bone healing process. We briefly discuss the clinical course of implant failure, with a prime focus on orthopedic implants. We identify the different anti-infective coating strategies and hence several anti-infective agents which could be incorporated in the hydrogel matrix. The fundamental design criteria to be considered while fabricating anti-infective hydrogels for orthopedic implants will be discussed. We highlight the different hydrogel coatings based on the origin of the polymers involved in light of their antimicrobial efficacy. We summarize the relevant patents reported in the prevention of implant infections, including orthopedics. Finally, the challenges concerning the clinical translation of the aforesaid hydrogels are described, and considerable solutions for improved clinical practice and better future prospects are proposed.

Recent advances in the implant-based drug delivery in otorhinolaryngology

The surgical implant is an interdisciplinary therapeutic modality that offers unique advantages in the daily practice of otorhinolaryngology. Some well-known examples include cochlear implants, bone-anchored hearing aids, sinus stents, and tracheostomy tubes. Neuroprotective, osteogenic, anti-inflammatory, and antimicrobial effects are among their established or pursued functions. Implant-based drug delivery affords an efficient and potent approach to enhancing these therapeutic functions. Recent innovations have infiltrated all four elements of a drug-eluting implant. The purpose of this pre-clinical, biotechnology-oriented review is to discuss these developments in terms of the implant biomaterial, loaded medication, delivery pattern, and system fabrication. Cell-mediated neurotrophin release, fabrication of a hydroxyapatite-supported system, biodegradable polymer-based implants, and multiclass and multidrug delivery are some representative advancements. The ultimate goal here is to bridge the gap between biotechnology advances and clinical needs. The review is concluded with a perspective regarding the future opportunities and challenges in this popular and rapidly developing subject of research. STATEMENT OF SIGNIFICANCE: Surgical implants and local drug delivery are representative modern modalities of surgical treatment and medical treatment, respectively. Their synergy offers unique therapeutic advantages, such as minimal systemic side effects, proximity-related high efficiency, and potential absorbability. The applications of implant-based drug delivery have infiltrated otorhinolaryngology and head & neck surgery, which is well known for its related tissue diversity and surgical complexity. Examples discussed here include cochlear implants, bone-anchored hearing aids, sinus stents, and airway tubes. This timely review focuses primarily on the four fundamental components of an implant-based drug delivery system, namely implant biomaterial, loaded medication, delivery pattern, and system fabrication. A particular emphasis is placed upon the in vitro cellular and in vivo animal studies that demonstrate pre-clinical potentials.

Steering the Clinical Translation of Delivery Systems for Drugs and Health Products

Besides the feasibility for industrial scale-up, accelerating the translation from bench to bedside of new technological strategies for controlled delivery and targeting of drugs and other actives relevant for health management, such as medical devices and nutraceuticals, would benefit from an even earlier evaluation in pre-clinical models and clinical settings. At the same time, translational medicine also performs in the opposite direction, incorporating clinical needs and observations into scientific hypotheses and innovative technological proposals. With these aims, the sessions proposed for the 2019 CRS Italy Chapter Workshop will introduce the experience of Italian and worldwide researchers on how to foster the actual work in controlled release and drug delivery towards a reliable pre-clinical and clinical assessment.

Comparison of sonication with chemical biofilm dislodgement methods using chelating and reducing agents: Implications for the microbiological diagnosis of implant associated infection

The diagnosis of implant-associated infections is hampered due to microbial adherence and biofilm formation on the implant surface. Sonication of explanted devices was shown to improve the microbiological diagnosis by physical removal of biofilms. Recently, chemical agents have been investigated for biofilm dislodgement such as the chelating agent ethylenediaminetetraacetic acid (EDTA) and the reducing agent dithiothreitol (DTT). We compared the activity of chemical methods for biofilm dislodgement to sonication in an established in vitro model of artificial biofilm. Biofilm-producing laboratory strains of Staphylococcus epidermidis (ATCC 35984), S. aureus (ATCC 43300), E. coli (ATCC 25922) and Pseudomonas aeruginosa (ATCC 53278) were used. After 3 days of biofilm formation, porous glass beads were exposed to control (0.9% NaCl), sonication or chemical agents. Quantitative and qualitative biofilm analyses were performed by colony counting, isothermal microcalorimetry and scanning electron microscopy. Recovered colony counts after treatment with EDTA and DTT were similar to those after exposure to 0.9% NaCl for biofilms of S. epidermidis (6.3 and 6.1 vs. 6.0 log10 CFU/mL, S. aureus (6.4 and 6.3 vs. 6.3 log10 CFU/mL), E. coli (5.2 and 5.1 vs. 5.1 log10 CFU/mL and P. aeruginosa (5.1 and 5.2 vs. 5.0 log10 CFU/mL, respectively). In contrast, with sonication higher CFU counts were detected with all tested microorganisms (7.5, 7.3, 6.2 and 6.5 log10 CFU/mL, respectively) (p <0.05). Concordant results were observed with isothermal microcalorimetry and scanning electron microscopy. In conclusion, sonication is superior to both tested chemical methods (EDTA and DTT) for dislodgement of S. epidermidis, S. aureus, E. coli and P. aeruginosa biofilms. Future studies may evaluate potential additive effect of chemical dislodgement to sonication.

Interpenetrating Hydrogel Networks Enhance Mechanical Stability, Rheological Properties, Release Behavior and Adhesiveness of Platelet-Rich Plasma

Platelet-rich plasma (PRP) has attracted much attention for the treatment of articular cartilage defects or wounds due to its intrinsic content of growth factors relevant for tissue repair. However, the short residence time of PRP in vivo, due to the action of lytic enzymes, its weak mechanical properties and the consequent short-term release of bioactive factors has restricted its application and efficacy. The present work aimed at designing new formulation strategies for PRP, based on the use of platelet concentrate (PC)-loaded hydrogels or interpenetrating polymer networks, directed at improving mechanical stability and sustaining the release of bioactive growth factors over a prolonged time-span. The interpenetrating hydrogels comprised two polymer networks interlaced on a molecular scale: (a) a first covalent network of thermosensitive and biodegradable vinyl sulfone bearing p(hydroxypropyl methacrylamide-lacate)-polyethylene glycol triblock copolymers, tandem cross-linked by thermal gelation and Michael addition when combined with thiolated hyaluronic acid, and (b) a second network composed of cross-linked fibrin. The PC-loaded hydrogels, instead, was formed only by network (a). All the designed and successfully synthesized formulations greatly increased the stability of PRP in vitro, leading to significant increase in degradation time and storage modulus of PRP gel. The resulting viscoelastic networks showed the ability to controllably release platelet derived growth factor and transforming growth factr β1, and to improve the tissue adhesiveness of PRP. The newly developed hydrogels show great potential for application in the field of wound healing, cartilage repair and beyond.

Localized controlled release of bevacizumab and doxorubicin by thermo-sensitive hydrogel for normalization of tumor vasculature and to enhance the efficacy of chemotherapy

In a malignant tumor, overexpression of pro-angiogenic factors like vascular endothelial growth factor (VEGF) provokes the production of pathologic vascular networks characterized by leaky, chaotically organized, immature, thin-walled, and ill-perfused. As a result, hostile tumor environment would be developed and profoundly hinders anti-cancer drug activities and fuels tumor progression. In this study, we develop a strategy of sequential sustain release of anti-angiogenic drug, Bevacizumab (BVZ), and anti-cancer drug, Doxorubicin (DOX), using poly (d, l-Lactide)- Poly (ethylene glycol) -Poly (d, l-Lactide) (PDLLA-PEG-PDLLA) hydrogel as a local delivery system. The release profiles of the drugs from the hydrogel were investigated in vitro which confirmed that relatively rapid release of BVZ (73.56 ± 1.39%) followed by Dox (61.21 ± 0.62%) at pH 6.5 for prolonged period. The in vitro cytotoxicity test revealed that the copolymer exhibited negligible cytotoxicity up to 2.5 mg ml^-1 concentration on HaCaT and HeLa cells. Likeways, the in vitro degradation of the copolymer showed 41.63 ± 2.62% and 73.25 ± 4.36% weight loss within 6 weeks at pH 7.4 and 6.5, respectively. After a single intratumoral injection of the drug-encapsulated hydrogel on Hela xenograft nude, hydrogel co-loaded with BVZ and Dox displayed the highest tumor suppression efficacy for up to 36 days with no noticeable damage on vital organs. Therefore, localized co-delivery of anti-angiogenic drug and anti-cancer drug by hydrogel system may be a promising approach for enhanced chemotherapeutic efficacy in cancer treatment.

Chitin and Chitosans: Characteristics, Eco-Friendly Processes, and Applications in Cosmetic Science

Huge amounts of chitin and chitosans can be found in the biosphere as important constituents of the exoskeleton of many organisms and as waste by worldwide seafood companies. Presently, politicians, environmentalists, and industrialists encourage the use of these marine polysaccharides as a renewable source developed by alternative eco-friendly processes, especially in the production of regular cosmetics. The aim of this review is to outline the physicochemical and biological properties and the different bioextraction methods of chitin and chitosan sources, focusing on enzymatic deproteinization, bacteria fermentation, and enzymatic deacetylation methods. Thanks to their biodegradability, non-toxicity, biocompatibility, and bioactivity, the applications of these marine polymers are widely used in the contemporary manufacturing of biomedical and pharmaceutical products. In the end, advanced cosmetics based on chitin and chitosans are presented, analyzing different therapeutic aspects regarding skin, hair, nail, and oral care. The innovative formulations described can be considered excellent candidates for the prevention and treatment of several diseases associated with different body anatomical sectors.

Isothermal Microcalorimetry Detects the Presence of Persister Cells in a Staphylococcus aureus Biofilm After Vancomycin Treatment

Staphylococcus aureus biofilm plays a major role in implant-associated infections. Here, the susceptibility of biofilm S. aureus to daptomycin, fosfomycin, vancomycin, trimethoprim/sulfamethoxazole, linezolid, and rifampicin was investigated by isothermal microcalorimetry (IMC). Moreover, the persister status of cells isolated from S. aureus biofilm after treatment with vancomycin was also analyzed. S. aureus biofilm was tolerant to all the antibiotics tested [minimum biofilm bactericidal concentration (MBBC) > 256 μg/ml], except to daptomycin [MBBC and minimum biofilm eradicating concentration (MBEC) = 32 μg/ml] and rifampin (MBBC and MBEC = 128 μg/ml). After the treatment of MRSA biofilm with 1024 μg/ml vancomycin, ∼5% cells survived, although metabolically inactive (persisters). Interestingly, IMC revealed that persister bacteria reverted to a normal-growing phenotype when inoculated into fresh medium without antibiotics. A staggered treatment of MRSA biofilm with vancomycin to kill all the metabolically active cells and daptomycin to kill persister cells eradicated the whole bacterial population. These results support the use in the clinical practice of a therapeutic regimen based on the use of two antibiotics to kill persister cells and eradicate MRSA biofilms. IMC represents a suitable technique to characterize in real-time the reversion from persister to metabolically-active cells.

Antimicrobial photodynamic therapy alone or in combination with antibiotic local administration against biofilms of Fusobacterium nucleatum and Porphyromonas gingivalis

Antimicrobial photodynamic therapy (aPDT) kills several planktonic pathogens. However, the susceptibility of biofilm-derived anaerobic bacteria to aPDT is poorly characterized. Here, we evaluated the effect of Photodithazine (PDZ)-mediated aPDT on Fusobacterium nucleatum and Porphyromonas gingivalis biofilms. In addition, aPDT was tested with metronidazole (MTZ) to explore the potential antimicrobial effect of the treatment. The minimum inhibitory concentration (MIC) of MTZ was defined for each bacterial species. Single-species biofilms of each species were grown on polystyrene plates under anaerobic conditions for five days. aPDT was performed by applying PDZ at concentrations of 50, 75 and 100 mg/L, followed by exposure to 50 J/cm² LED light (660 nm) with or without MTZ. aPDT exhibited a significant reduction in bacterial viability at a PDZ concentration of 100 mg/L, with 1.12 log₁₀ and 2.66 log₁₀ reductions for F. nucleatum and P. gingivalis in biofilms, respectively. However, the antimicrobial effect against F. nucleatum was achieved only when aPDT was combined with MTZ at 100× MIC. Regarding P. gingivalis, the combination of PDZ-mediated aPDT at 100 mg/L with MTZ 100× MIC resulted in a 5 log₁₀ reduction in the bacterial population. The potential antimicrobial effects of aPDT in combination with MTZ for both single pathogenic biofilms were confirmed by live/dead staining. These results suggest that localized antibiotic administration may be an adjuvant to aPDT to control F. nucleatum and P. gingivalis biofilms.