A novel photoelectrochemical sensor based on molecularly imprinted polymer modified TiO2 nanotubes and its highly selective detection of 2,4-dichlorophenoxyacetic acid

Wavelength-dependent photoelectrochemical response demonstrated by the determination of acetaminophen and rutin in differential molecularly imprinted polymers strategy

Herein, the excitation wavelength-dependent responses of the molecularly imprinted polymer (MIP) photoelectrochemical (PEC) sensors were investigated, using acetaminophen (AP), rutin (RT) and perfluorooctanoate (PFOA) as the model templates, pyrrole as functional monomer, CuInS2@ZnS/TiO2 NTs as the basic photoelectrode. With wavelength λ > 240 nm, the photocurrent of MIPPFOA enhanced at higher concentrations of PFOA. With increasing AP concentration, the photocurrents of MIPAP could decline with λ < 271 nm, not change at λ = 270 nm, or increase with λ > 270 nm. As RT concentration increased, the photocurrents of MIPRT could decrease (λ < 431 nm), not change (λ = 431 nm) or increase (λ > 431 nm). The PEC responses depend on the comprehensive interaction of two contrary mechanisms from the template molecules within the MIP membrane. The photocurrent is enhanced by the role of the electron donor for photo-generated holes but attenuated due to the steric hindrance effect and the excitation light intensity loss via absorption or scattering. The apparent molar absorption coefficient of AP and RT within MIP membranes are 9.1-19.4 folds of those measured from dilute solutions. By using a routine UV lamp as the light source, the photocurrents of MIPRT at 254 nm and MIPAP at 365 nm were used to determine RT and AP, with the detection limits of 5.3 and 16 nM, respectively. The interference from the non-specific adsorption of interferents on the surfaces of MIPAP and MIPRT was reduced by one order of magnitude via a differential strategy.

Unveiling the Latest Developments in Molecularly Imprinted Photocatalysts: A State-of-the-Art Review

Responding to the growing concerns about environmental pollutants, scientists are increasingly turning to innovative solutions rooted in the field of environmental science. One such promising avenue combines the robustness of traditional photocatalysis with the precision of molecular imprinting, leading to the proposition of molecularly imprinted photocatalysts (MIPCs). These MIPCs hold the potential to specifically target and eliminate environmental pollutants, marking them as a promising tool in modern environmental remediation. As researchers delve deeper into this field, the design and optimization of MIPCs have become hotbeds for scientific inquiry. This comprehensive overview delves into the multifaceted approaches to MIPC design, elucidating on aspects like the selection of appropriate photocatalytic bases, the pivotal role of templates, the choice of monomeric building blocks, and the integration of effective cross-linking agents. However, as with all burgeoning technologies, the development of MIPCs is not without its challenges. These potential impediments to the successful innovation and implementation of MIPCs are also explored.

Au/TiO2-based molecularly imprinted photoelectrochemical sensor for dibutyl phthalate detection

A photoelectrochemical molecular imprinting sensor based on Au/TiO₂ nanocomposite was constructed for the detection of dibutyl phthalate. Firstly, TiO₂ nanorods were grown on fluorine-doped tin oxide substrate by hydrothermal method. Then, gold nanoparticles were electrodeposited on TiO₂ to fabricate Au/TiO₂. Finally, molecular imprinted polymer was electropolymerized on the Au/TiO₂ surface to construct MIP/Au/TiO₂ PEC sensor for DBP. The conjugation effect of MIP accelerates the electron transfer between TiO₂ and MIP, which can greatly improve the photoelectric conversion efficiency and sensitivity of the sensor. In addition, MIP can also provide sites for highly selective recognition of dibutyl phthalate molecules. Under optimal experimental conditions, the prepared photoelectrochemical sensor was used for the quantitative determination of DBP and the results showed a wide linear range (50 to 500 nM), a low limit of detection (0.698 nM), and good selectivity. The sensor was used in a study of real water samples to show that it has promising applications in environmental analysis.

Machine learning-assisted Te-CdS@Mn3O4 nano-enzyme induced self-enhanced molecularly imprinted ratiometric electrochemiluminescence sensor with smartphone for portable and visual monitoring of 2,4-D

Here, a novel and portable machine learning-assisted smartphone-based visual molecularly imprinted ratiometric electrochemiluminescence (MIRECL) sensing platform was constructed for highly selective sensitive detection of 2,4-Dichlorophenoxyacetic acid (2,4-D) for the first time. Te doped CdS-coated Mn₃O₄ (Te-CdS@Mn₃O₄) with catalase-like activity served as cathode-emitter, while luminol as anode luminophore accompanied H₂O₂ as co-reactant, and Te-CdS@Mn₃O₄ decorated molecularly imprinted polymers (MIPs) as recognition unit, respectively. Molecular models were constructed and MIP band and binding energies were calculated to elucidate the luminescence mechanism and select the best functional monomers. The peroxidase activity and the large specific surface area of Mn₃O₄ and the electrochemical effect can significantly improve the ECL intensity and analytical sensitivity of Te-CdS@Mn₃O₄. 2,4-D-MIPs were fabricated by in-situ electrochemical polymerization, and the rebinding of 2,4-D inhibits the binding of H₂O₂ to the anode emitter, and with the increase of the cathode impedance, the ECL response of Te-CdS@Mn₃O₄ decreases significantly. However, the blocked reaction of luminol on the anode surface also reduces the ECL response. Thus, a double-reduced MIRECL sensing system was designed and exhibited remarkable performance in sensitivity and selectivity due to the specific recognition of MIPs and the inherent ratio correction effect. Wider linear range in the range of 1 nM-100 μM with a detection limit of 0.63 nM for 2,4-D detection. Interestingly, a portable and visual smartphone-based MIRECL analysis system was established based on the capture of luminescence images by smartphones, classification and recognition by convolutional neural networks, and color analysis by self-developed software. Therefore, the developed MIRECL sensor is suitable for integration with portable devices for intelligent, convenient, and fast detection of 2,4-D in real samples.

[Advances in application of molecularly imprinted polymers to the detection of polar pesticide residues]

Polar pesticides can be primarily classified as fungicides, herbicides, and insecticides; their rich variety and low cost have led to their extensive utilization in agriculture. However, the overuse of polar pesticides can lead to environmental contamination, such as water or soil pollution, which can also increase the risk of pesticide exposure among human life directly, or indirectly through contact with animal and plant-derived food. There are considerable differences in the physical and chemical properties of polar pesticides, as well as their trace amounts in complex food and environmental samples, posing immense challenges to their accurate detection. As a kind of artificially prepared selective adsorbent, molecularly imprinted polymers (MIPs) possess specific recognition sites complementary to template molecules in terms of the spatial structure, size, and chemical functional groups. With many advantages such as easy preparation, low cost, as well as good chemical and mechanical stability, MIPs have been widely applied in sample pretreatment and the analysis of polar pesticide residues. MIPs are typically used as adsorption materials in solid phase extraction (SPE) methods, including magnetic solid phase extraction (MSPE), dispersed solid phase extraction (DSPE), and stir bar sorptive extraction (SBSE). To rapidly detect polar pesticide residues with high sensitivity, MIPs are also used in the preparation of fluorescent sensors and electrochemical sensors. Furthermore, MIPs can be employed as the substrate in surface-enhanced Raman spectroscopy and as the substrate for the ion source in mass spectrometry for polar pesticide residue analysis. Thus far, various molecularly imprinted materials have been reported for the efficient separation and analysis of polar pesticide residues in various complex matrices. However, there is no review that summarizes the recent advances in MIPs for the determination of polar pesticides. This review introduces imprinting strategies and polymerization methods for MIPs, and briefly summarizes some new molecular imprinting strategies and preparation technologies. The application of MIPs in recent years (particularly the last five years) to the detection of polar pesticide residues including neonicotinoids, organophosphorus, triazines, azoles, and urea is then systematically summarized. Finally, the future development direction and trends for MIPs are proposed considering existing challenges, with the aim of providing reference to guide future research on MIPs in the field of polar pesticide residue detection.

The radical and non-radical oxidation mechanism of electrochemically activated persulfate process on different cathodes in divided and undivided cell

Electrochemically activated persulfate (PS) employing stainless steel (SS), carbon felt (CF) and carbon black modified CF (CB-CF) as the cathode, in the divided and undivided cell, respectively, for degradation of atrazine (ATZ) was first investigated using novel B, Co-doped TiO₂ nanotubes (B, Co-TNT) anode. In undivided cell, ATZ degradation was followed the order of CF<CB-CF<SS. The main radical for ATZ removal in SS and CF system was ^•OH, while on CB-CF cathode, it was the comprehensive contribution of ^•OH and SO₄^•-. ^•OH in SS system was more inclined to free ^•OH, while in CF and CB-CF systems it was more likely to be surface ^•OH. In divided anode cell, ^•OH was responsible for ATZ degradation in all three cathodes system. However, in divided cathode cell, ^•OH played a major role for ATZ degradation in SS cathode system. In CF and CB-CF cathode systems, the ATZ degradation was the comprehensive effect of ^•OH and SO₄^•- with the contribution of ^•OH and SO₄^•- was 91.7%, 8.3%, and 96.3%, 3.6%, respectively. The quenching studies showed that non-radical oxidation occurred in anode chamber in the presence of PS. Besides, the intermediates in divided and undivided cell were detected by LC-MS, and the possible degradation pathway was proposed.

A Review of Nanocomposite-Modified Electrochemical Sensors for Water Quality Monitoring

Electrochemical sensors play a significant role in detecting chemical ions, molecules, and pathogens in water and other applications. These sensors are sensitive, portable, fast, inexpensive, and suitable for online and in-situ measurements compared to other methods. They can provide the detection for any compound that can undergo certain transformations within a potential window. It enables applications in multiple ion detection, mainly since these sensors are primarily non-specific. In this paper, we provide a survey of electrochemical sensors for the detection of water contaminants, i.e., pesticides, nitrate, nitrite, phosphorus, water hardeners, disinfectant, and other emergent contaminants (phenol, estrogen, gallic acid etc.). We focus on the influence of surface modification of the working electrodes by carbon nanomaterials, metallic nanostructures, imprinted polymers and evaluate the corresponding sensing performance. Especially for pesticides, which are challenging and need special care, we highlight biosensors, such as enzymatic sensors, immunobiosensor, aptasensors, and biomimetic sensors. We discuss the sensors' overall performance, especially concerning real-sample performance and the capability for actual field application.

Microfluidic Affinity Sensor Based on a Molecularly Imprinted Polymer for Ultrasensitive Detection of Chlorpyrifos

The persistent use of pesticides in the agriculture field remains a serious issue related to public health. In the present work, molecularly imprinted polymer thin films were developed using electropolymerization of pyrrole (py) onto gold microelectrodes followed by electrodeposition for the selective detection of chlorpyrifos (CPF). The molecularly imprinted polymer (MIP) was synthesized by the electrochemical deposition method, which allowed in-line transfer of MIP on gold microelectrodes without using any additional adhering agents. Various parameters such as pH, monomer ratio, scan rate, and deposition cycle were optimized for sensor fabrication. The sensor was characterized at every stage of fabrication using various spectroscopic, microscopic, and electrochemical techniques. The sensor requires only 2 μL of the analyte and its linear detection range was found to be 1 μM to 1 fM. The developed sensor's limit of detection (LOD) and limit of quantification (LOQ) were found to be 0.93 and 2.82 fM, respectively, with a sensitivity of 3.98 (μA/(μM)/ mm². The sensor's shelf life was tested for 70 days. The applicability of the sensor in detecting CPF in fruit and vegetable samples was also assessed out with recovery % between 91 and 97% (RSD < 5%). The developed sensor possesses a huge commercial potential for on-field monitoring of pesticides.

Multiplexed Readout of Enzymatic Reactions by Means of Laterally Resolved Illumination of Quantum Dot Electrodes

Triggering electrochemical reactions with light provides a powerful tool for the control of complex reaction schemes on photoactive electrodes. Here, we report on the light-directed, multiplexed detection of enzymatic substrates using a nonstructured gold electrode modified with CdSe/ZnS quantum dots (QDs) and two enzymes, glucose oxidase (GOx) and sarcosine oxidase (SOx). While QDs introduce visible-light sensitivity into the electrode architecture, GOx and SOx allow for a selective conversion of glucose and sarcosine, respectively. For the QD immobilization to the gold electrode, a linker-assisted approach using trans-4,4'-stilbenedithiol has been used, resulting in the generation of a photocurrent. Subsequently, GOx and SOx have been immobilized in spatially separated spots onto the QD electrode. For the local readout of the QD electrode, a new measurement setup has been developed by moving a laser pointer across the surface to defined positions on the chip surface. The amplitudes of the photocurrents upon illumination of the GOx or SOx spot depend in a concentration-dependent manner on the presence of glucose and sarcosine, respectively. This measurement also allows for a selective detection in the presence of other substances. The setup demonstrates the feasibility of multiplexed measurements of enzymatic reactions using a focused light pointer, resulting in an illumination area with a diameter of 0.3 mm for analyzing spots of different enzymes. Moving the laser pointer in the x- and y-direction and simultaneously detecting the local photocurrent also allow a spatial imaging of enzyme immobilization. Here, not only the spot dimensions but also the activity of the enzyme can be verified.

A Formaldehyde Sensor Based on Molecularly-Imprinted Polymer on a TiO₂ Nanotube Array

Today, significant attention has been brought to the development of sensitive, specific, cheap, and reliable sensors for real-time monitoring. Molecular imprinting technology is a versatile and promising technology for practical applications in many areas, particularly chemical sensors. Here, we present a chemical sensor for detecting formaldehyde, a toxic common indoor pollutant gas. Polypyrrole-based molecularly-imprinted polymer (PPy-based MIP) is employed as the sensing recognition layer and synthesized on a titanium dioxide nanotube array (TiO₂-NTA) for increasing its surface-to-volume ratio, thereby improving the sensor performance. Our sensor selectively detects formaldehyde in the parts per million (ppm) range at room temperature. It also shows a long-term stability and small fluctuation to humidity variations. These are attributed to the thin fishnet-like structure of the PPy-based MIP on the highly-ordered and vertically-aligned TiO₂-NTA.

Visible-light-activated photoelectrochemical biosensor for the detection of the pesticide acetochlor in vegetables and fruit based on its inhibition of glucose oxidase

A new and sensitive photoelectrochemical (PEC) biosensor which is visible-light-activated was fabricated based on acetochlor’s ability to inhibit glucose oxidase (GOx) activity.

Titania nanostructures: a biomedical perspective

A systematic and comprehensive summary of various TNS-based biomedical research with a special emphasis on drug-delivery, tissue engineering, biosensor, and anti-bacterial applications.

Excellent graphitic carbon nitride nanosheets-based photoelectrochemical platform motivated by Schottky barrier and LSPR effect and its sensing application

A visible light responsive photocatalytic hybrid with excellent photoelectrochemical activity was first fabricated via the self-assembly of Au nanorods onto poly(l-cysteine) modified graphitic carbon nitride nanosheets.

Molecular imprinting science and technology: a survey of the literature for the years 2004-2011

Herein, we present a survey of the literature covering the development of molecular imprinting science and technology over the years 2004-2011. In total, 3779 references to the original papers, reviews, edited volumes and monographs from this period are included, along with recently identified uncited materials from prior to 2004, which were omitted in the first instalment of this series covering the years 1930-2003. In the presentation of the assembled references, a section presenting reviews and monographs covering the area is followed by sections describing fundamental aspects of molecular imprinting including the development of novel polymer formats. Thereafter, literature describing efforts to apply these polymeric materials to a range of application areas is presented. Current trends and areas of rapid development are discussed.

Simple synthesis and photoelectrochemical characterizations of polythiophene/Pd/TiO2 composite microspheres

We report here a simple, effective, and low cost method to synthesize polythiophene/Pd/TiO2 (PTh/Pd/TiO2) ternary composite microspheres and apply such a composite to photoelectrochemical (PEC) sensing. TiO2 spherical aggregates of 200 nm diameter, consisting of nanoscale building blocks of TiO2, have been prepared by hydrolysis of tetrabutyl titanate in a water-in-oil emulsion system (Vwater/Vacetone=1/100). Pd species and PTh layer were decorated onto TiO2 microspherical substrates by reduction of Pd salts and polymerization of thiophene, respectively. The high surface area, effective charge transfer, and enhanced light absorption of the ternary composite could improve PEC performance under simulated sunlight. The sensitivity, selectivity, and stability of PEC sensor for detecting l-cysteine were much higher than those of the traditional electrochemical sensor. The detection limit of l-cysteine was 9.24 μM in the linear range of 0.31-5.30 mM. Moreover, the results also indicated a good anti-interference and acceptable accuracy in practical application, providing a rapid and sensitive detection method.

A highly selective photoelectrochemical biosensor for uric acid based on core-shell Fe3O4@C nanoparticle and molecularly imprinted TiO2

Combining the surface modification and molecular imprinting technique, a novel photoelectrochemical sensing platform with excellent photochemical catalysis and molecular recognition capabilities was established for the detection of uric acid based on the magnetic immobilization of Fe3O4@C nanoparticles onto magnetic glassy carbon electrode (MGCE) and modification of molecularly imprinted TiO2 film on Fe3O4@C. The developed biosensor was highly sensitive to uric acid in solutions, with a linear range from 0.3 to 34µM and a limit of detection of 0.02μM. Furthermore, the biosensor exhibited outstanding selectivity while used in coexisting systems containing various interferents with high concentration. The practical application of the biosensor was also realized for the selective detection of uric acid in spiked samples. The study made a successful attempt in the development of highly selective and sensitive photoelectrochemical biosensor for urine monitoring.

Construction of photoelectrochemical thrombin aptasensor via assembling multilayer of graphene-CdS nanocomposites

A photoelectrochemical (PEC) aptasensor for highly sensitive and specific detection of thrombin was developed by using graphene–CdS nanocomposites multilayer as photoactive species and electroactive mediator hexaammineruthenium(III) chloride (Ru(NH(3))(6)(3+)) as signal enhancer. Graphene–CdS nanocomposites (G–CdS) were synthesized by one-pot reduction of oxide graphene and CdCl2 with thioacetamide. The photoactive multilayer was prepared by alternative assembly of the negatively charged 3-mercaptopropionic acid modified graphene–CdS nanocomposites (MPA-G–CdS) and the positively charged polyethylenimine (PEI) on ITO electrode. This layer-by-layer assembly method enhanced the stability and homogeneity of the photocurrent readout of G–CdS. Thrombin aptamer was covalently bound to the multilayer by using glutaraldehyde as cross-linking. Electroactive mediator (Ru(NH(3))(6)(3+)) could interact with the DNA phosphate backbone and thus facilitated the electron transfer between G–CdS multilayer and electrode and enhanced the photocurrent. Hybridizing of a long complementary DNA with thrombin aptamer could increase the adsorption amount of (Ru(NH(3))(6)(3+)), which in turn boosted the signal readout. In the presence of target thrombin, the affinity interaction between thrombin and its aptamer resulted in the long complementary DNA releasing from the G–CdS multilayer and decreasing of photocurrent signal. On the basis of G–CdS multilayer as the photoactive species, (Ru (NH(3))(6)(3+)) as an electroactive mediator, and aptamer as a recognition module, a high sensitive PEC aptasensor for thrombin detection was proposed. The thrombin aptasensor displayed a linear range from 2.0 pM to 600.0 pM and a detection limit of 1.0 pM. The present strategy provided a promising ideology for the future development of PEC biosensor.

Nanostructured photoelectrochemical biosensor for highly sensitive detection of organophosphorous pesticides

A sensitive photoelectrochemical (PEC) biosensor for detection of organophosphorus pesticides (OPs) using the nanocomposite of CdSe@ZnS quantum dots (QDs) and graphene deposited on the ITO coated glass electrode as a photoactive electrode is presented. The integration of CdSe@ZnS/graphene nanocomposite with biomolecules acetylcholinesterase (AChE) as a biorecognition element yields a novel biosensing platform. Under visible light irradiation, the AChE-CdSe@ZnS/graphene nanocomposite can generate a stable photocurrent and the photocurrent is found to be inversely dependent on the concentration of OPs. Under the optimal experimental conditions, the photocurrents were proportional to the logarithm of paraoxon and dichlorvos within the concentration range of 10(-12)-10(-6) M. The detection limits (LOD) of the proposed biosensor for paraoxon and dichlorvos are as low as 10(-14) M and 10(-12) M. The photoelectrochemical biosensor shows good sensitivity, reproducibility, stability, and could be successfully applied to detection of OPs in real fruit samples.

Nanostructure-based optoelectronic sensing of vapor phase explosives--a promising but challenging method

Optoelectronic sensing of gas phase hazardous chemicals is a newly explored field, which shows great advantages towards low concentration sensing when compared to normal gas sensing in the dark. Here, based on the recent progress on nanostructured vapor phase explosive gas sensors operated in dark conditions, the attractiveness of developing optoelectronic sensors for vapor phase explosive detection was highlighted. Furthermore, we try to propose some new insights to enhance optoelectronic sensing of vapor phase explosives. We suggest employing photocatalysis principles to enhance the sensitivity and employing a molecular imprinting technique (MIT) to enhance the selectivity.

Femtomole level photoelectrochemical aptasensing for mercury ions using quercetin-copper(II) complex as the DNA intercalator

An ultrasensitive and selective photoelectrochemical (PEC) aptasensor for mercury ions was first fabricated based on perylene-3, 4, 9, 10-tetracarboxylic acid/graphene oxide (PTCA/GO) heterojunction using quercetin-copper(II) complex intercalated into the poly(dT)-poly(dA) duplexes. Both the PTCA/GO heterojunction and the quercetin-copper(II) complex are in favor of the sensitivity for the fabricated PEC aptasensor due to band alignment and strong reduction capability, respectively. And they efficiently promote the separation of photoexcited carriers and enhance the photocurrent. The formation of thymine-Hg(2+)-thymine coordination chemistry resulted in the dehybridization of poly(dT)-poly(dA) duplexes and then the intercalator quercetin-copper(II) complex broke away from the surface of the PEC aptasensor. As the concentration of mercury ions increased, the photocurrent gradually decreased. The electrode response for mercury ions detection was in the linear range from 0.01 pmol L(-1) to 1.00 pmol L(-1) with the detection limit of 3.33 fmol L(-1). The label-free PEC aptasensor has excellent performances with ultrasensitivity and good selectivity besides the advantage of economic and facile fabrication. The strategy of quercetin-copper(II) complex as a novel DNA intercalator paves a new way to improve the performances for PEC sensors.

A photoelectrochemical biosensor for o-aminophenol based on assembling of CdSe and DNA on TiO2 film electrode

A novel photoelectrochemical (PEC) biosensing platform was constructed by assembling CdSe quantum dots (QDs) and DNA on liquid phase deposited TiO2 (DNA-CdSe/TiO2) film electrode. The transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis indicated that CdSe QDs were homogeneously assembled on TiO2 film. The UV-visible diffuse reflectance spectra (DRS) showed that CdSe and DNA could effectively enhance the absorption of TiO2 film to visible light. The obtained electrode showed a sensitive PEC response to o-aminophenol (OAP) under visible light irradiation. Due to the interaction between DNA and OAP, the response of OAP was improved by DNA immobilized on the sensing film. Under optimized conditions, the photocurrent was linearly proportional to OAP in the concentration range from 4.0 × 10(-7) to 2.7 × 10(-5) mol L(-1), with a detection limit (3S/N) of 8.0 × 10(-8) mol L(-1). The novel strategy could provide a fast and sensitive method for OAP determination.