Water-processable polypyrrole microparticle modules for direct fabrication of hierarchical structured electrochemical interfaces

Magnetic microsphere sorbent on CaCO3 templates: Simple synthesis and efficient extraction of trace carbamate pesticides in fresh produce

Polypyrrole magnetic microspheres were synthesized and used to extract carbaryl, carbofuran, and methomyl before analysis by a high-performance liquid chromatography with diode array detection. Under optimal conditions, four times the preconcentration was achieved with the use of only 1.2 mL of sample. Good linearity with ranges of 3.0-7.5 × 10³, 6.0-4.5 × 10³, and 15-3.0 × 10³ ng kg^-1 and limits of detection of 1.37 ± 0.10, 4.7 ± 1.2, and 10.1 ± 5.7 ng kg^-1 were obtained, respectively. Good reproducibility (RSDs < 5%) was achieved over 24 cycles of extraction and regeneration. Good accuracy (recoveries 81.6 ± 1.5%-108.3 ± 2.2%) and good precision (RSDs 0.11%-4.5%) were obtained. Carbaryl was detected in apple (2.75 ± 0.23 ng kg^-1), carbofuran in tomato (11.34 ± 0.61 ng kg^-1), and methomyl in watermelon (34.7 ± 1.7 ng kg^-1). The relative expanded uncertainty of the measurement method was less than 14% for all three pesticides.

Tunable 3D nanofibrous and bio-functionalised PEDOT network explored as a conducting polymer-based biosensor

Conducting polymers that possess good electrochemical properties, nanostructured morphology and functionality for bioconjugation are essential to realise the concept of all-polymer-based biosensors that do not depend on traditional nanocatalysts such as carbon materials, metal, metal oxides or dyes. In this research, we demonstrated a facile approach for the simultaneous preparation of a bi-functional PEDOT interface with a tunable 3D nanofibrous network and carboxylic acid groups (i.e. Nano-PEDOT-COOH) via controlled co-polymerisation of EDOT and EDOT-COOH monomers, using tetrabutylammonium perchlorate as a soft-template. By tuning the ratio between EDOT and EDOT-COOH monomer, the nanofibrous structure and carboxylic acid functionalisation of Nano-PEDOT-COOH were varied over a fibre diameter range of 15.6 ± 3.7 to 70.0 ± 9.5 nm and a carboxylic acid group density from 0.03 to 0.18 μmol cm^-2. The nanofibres assembled into a three-dimensional network with a high specific surface area, which contributed to low charge transfer resistance and high transduction activity towards the co-enzyme NADH, delivering a wide linear range of 20-960 μM and a high sensitivity of 0.224 μA μM^-1 cm^-2 at the Nano-PEDOT-COOH50% interface. Furthermore, the carboxylic acid groups provide an anchoring site for the stable immobilisation of an NADH-dependent dehydrogenase (i.e. lactate dehydrogenase), via EDC/S-NHS chemistry, for the fabrication of a Bio-Nano-PEDOT-based biosensor for lactate detection which had a response time of less than 10 s over the range of 0.05-1.8 mM. Our developed bio-Nano-PEDOT interface shows future potential for coupling with multi-biorecognition molecules via carboxylic acid groups for the development of a range of advanced all-polymer biosensors.

The Use of Conducting Polymers for Enhanced Electrochemical Determination of Hydrogen Peroxide

The role of hydrogen peroxide in a wide range of biological processes has led to a steady increase in research into hydrogen peroxide determination in recent years, and conducting polymers have attracted much interest in electrochemistry as promising materials in this area. We present an overview of electrochemical devices for hydrogen peroxide determination using conducting polymers, either as a target or as a byproduct of redox reactions. We describe different combinations of electrode modifications through the incorporation of conducting polymers as the main component along with other materials or nanomaterials. We critically compare the analytical performances cited and highlight some of the future challenges for the feasible application of such devices.

Modulating Electrode Kinetics for Discrimination of Dopamine by a PEDOT:COOH Interface Doped with Negatively Charged Tricarboxylate

The rapidly developing field of conducting polymers in organic electronics has many implications for bioelectronics. For biosensing applications, tailoring the functionalities of the conducting polymer's surface is an efficient approach to improve both sensitivity and selectivity. Here, we demonstrated a facile and economic approach for the fabrication of a high-density, negatively charged carboxylic-acid-group-functionalized PEDOT (PEDOT:COOH) using an inexpensive ternary carboxylic acid, citrate, as a dopant. The polymerization efficiency was significantly improved by the addition of LiClO₄ as a supporting electrolyte yielding a dense PEDOT:COOH sensing interface. The resulting PEDOT:COOH interface had a high surface density of carboxylic acid groups of 0.129 μmol/cm² as quantified by the toluidine blue O (TBO) staining technique. The dopamine response measured with the PEDOT:COOH sensing interface was characterized by cyclic voltammetry with a significantly reduced ΔE_p of 90 mV and a 3-fold increase in the I_pa value compared with those of the nonfunctionalized PEDOT sensing interface. Moreover, the cyclic voltammetry and electrochemical impedance spectroscopy results demonstrated the increased electrode kinetics and highly selective discrimination of dopamine (DA) in the presence of the interferents ascorbic acid (AA) and uric acid (UA), which resulted from the introduction of negatively charged carboxylic acid groups. The negatively charged carboxylic acid groups could favor the transfer, preconcentration, and permeation of positively charged DA to deliver improved sensing performance while repelling the negatively charged AA and UA interferents. The PEDOT:COOH interface facilitated measurement of dopamine over the range of 1-85 μM, with a sensitivity of 0.228 μA μM^-1, which is 4.1 times higher than that of a nonfunctionalized PEDOT electrode (0.055 μA μM^-1). Our results demonstrate the feasibility of a simple and economic fabrication of a high-density PEDOT:COOH interface for chemical sensing, which also has the potential for coupling with other biorecognition molecules via carboxylic acid moieties for the development of a range of advanced PEDOT-based biosensors.

Electrosynthesis of Hydrogen Peroxide Synergistically Catalyzed by Atomic Co-Nx -C Sites and Oxygen Functional Groups in Noble-Metal-Free Electrocatalysts

Hydrogen peroxide (H₂ O₂ ) is a green oxidizer widely involved in a vast number of chemical reactions. Electrochemical reduction of oxygen to H₂ O₂ constitutes an environmentally friendly synthetic route. However, the oxygen reduction reaction (ORR) is kinetically sluggish and undesired water serves as the main product on most electrocatalysts. Therefore, electrocatalysts with high reactivity and selectivity are highly required for H₂ O₂ electrosynthesis. In this work, a synergistic strategy is proposed for the preparation of H₂ O₂ electrocatalysts with high ORR reactivity and high H₂ O₂ selectivity. A Co-N_x -C site and oxygen functional group comodified carbon-based electrocatalyst (named as Co-POC-O) is synthesized. The Co-POC-O electrocatalyst exhibits excellent catalytic performance for H₂ O₂ electrosynthesis in O₂ -saturated 0.10 m KOH with a high selectivity over 80% as well as very high reactivity with an ORR potential at 1 mA cm^-2 of 0.79 V versus the reversible hydrogen electrode (RHE). Further mechanism study identifies that the Co-N_x -C sites and oxygen functional groups contribute to the reactivity and selectivity for H₂ O₂ electrogeneration, respectively. This work affords not only an emerging strategy to design H₂ O₂ electrosynthesis catalysts with remarkable performance, but also the principles of rational combination of multiple active sites for green and sustainable synthesis of chemicals through electrochemical processes.

Positively-charged hierarchical PEDOT interface with enhanced electrode kinetics for NADH-based biosensors

Poly(ethylenedioxythiophene) (PEDOT) has attracted considerable attention as an advanced electrode material for electrochemical sensors and biosensors, due to its unique electrical and physicochemical properties. Here, we demonstrate the facile preparation of a positively-charged and hierarchical micro-structured PEDOT electrochemical interface with enhanced electrode kinetics for the electrooxidation of NADH. Processable PEDOT colloidal microparticles (PEDOT CMs) were synthesised by template-assisted polymerisation and were then utilised as building blocks for the fabrication of hierarchically-structured electrodes with a larger accessible electroactive surface (2.8 times larger than that of the benchmark PEDOT:PSS) and inter-particle space, thus improving electrode kinetics. The intrinsic positive charge of the PEDOT CMs further facilitated the detection of negatively-charged molecules by electrostatic accumulation. Due to the synergistic effect, these hierarchically-structured PEDOT CMs electrodes exhibited improved NADH electrooxidation at lower potentials and enhanced electrocatalytic activity compared to the compact structure of conventional PEDOT:PSS electrodes. The PEDOT CMs electrodes detected NADH over the range of 20-240 μM, with a sensitivity of 0.0156 μA/μM and a limit of detection of 5.3 μM. Moreover, the PEDOT CMs electrode exhibited a larger peak separation from the interferent ascorbic acid, and improved stability. This enhanced analytical performance for NADH provides a sound basis for further work coupling to a range of NAD-dependent dehydrogenases for applications in biosensing, bio-fuel cells and biocatalysis.

Fabrication of Protein Microparticles and Microcapsules with Biomolecular Tools

Microparticles have attracted much attention for medical, analytical and biological applications. Calcium carbonate (CaCO3) templating method with the advantages of having narrow size distribution, controlled morphology and good biocompatibility that has been widely used for the synthesis of various protein-based microparticles. Despite CaCO3 template is biocompatible, most of the conventional methods to create stable protein microparticles are mainly driven by chemical crosslink reagents which may induce potential harmful effect and remains undesirable especially for biomedical or clinical applications. In this article, we demonstrate the fabrication of protein microparticles and microcapsules with an innovative method using biomolecular tools such as enzymes and affinity molecules to trigger the assembling of protein molecules within a porous CaCO3 template followed by a template removal step. We demonstrated the enzyme-assisted fabrication of collagen microparticles triggered by transglutaminase, as well as the affinity-assisted fabrication of BSA-biotin avidin microcapsules triggered by biotin-avidin affinity interaction, respectively. Based on the different protein assemble mechanisms, the collagen microparticles appeared as a solid-structured particles, while the BSA-biotin avidin microcapsules appeared as hollow-structured morphology. The fabrication procedures are simple and robust that allows producing protein microparticles or microcapsules under mild conditions at physiological pH and temperature. In addition, the microparticle morphologies, protein compositions and the assemble mechanisms were studied. Our technology provides a facile approach to design and fabricate protein microparticles and microcapsules that are useful in the area of biomaterials, pharmaceuticals and analytical chemistry.

Printable Heterostructured Bioelectronic Interfaces with Enhanced Electrode Reaction Kinetics by Intermicroparticle Network

Printable organic bioelectronics provide a fast and cost-effective approach for the fabrication of novel biodevices, while the general challenge is to achieve optimized reaction kinetics at multiphase boundaries between biomolecules and electrodes. Here, we present an entirely new concept based on a modular approach for the construction of heterostructured bioelectronic interfaces by using tailored functional "biological microparticles" combined with "transducer microparticles" as modular building blocks. This approach offers high versatility for the design and fabrication of bioelectrodes with a variety of forms of interparticle spatial organization, from layered-structures to more advance bulk heterostructured architectures. The heterostructured biocatalytic electrodes delivered twice the reaction rate and a six-fold increase in the effective diffusion kinetics in response to a catalytic model using glucose as the substrate, together with the advantage of shortened diffusion paths for reactants between multiple interparticle junctions and large active particle surface. The consequent benefits of this improved performance combined with the simple means of mass production are of major significance for the emerging printed electronics industry.

A stretchable and screen-printed electrochemical sensor for glucose determination in human perspiration

Here we present two types of all-printable, highly stretchable, and inexpensive devices based on platinum (Pt)-decorated graphite for glucose determination in physiological fluids. Said devices are: a non-enzymatic sensor and an enzymatic biosensor, the latter showing promising results. Glucose has been quantified by measuring hydrogen peroxide (H2O2) reduction by chronoamperometry at -0.35V (vs pseudo-Ag/AgCl) using glucose oxidase immobilized on Pt-decorated graphite. The sensor performs well for the quantification of glucose in phosphate buffer solution (0.25M PBS, pH 7.0), with a linear range between 0 mM and 0.9mM, high sensitivity and selectivity, and a low limit of detection (LOD). Thus, it provides an alternative non-invasive and on-body quantification of glucose levels in human perspiration. This biosensor has been successfully applied on real human perspiration samples and results also show a significant correlation between glucose concentration in perspiration and glucose concentration in blood measured by a commercial glucose meter.

Stretchable Biofuel Cells as Wearable Textile-based Self-Powered Sensors

Highly stretchable textile-based biofuel cells (BFCs), acting as effective self-powered sensors, have been fabricated using screen-printing of customized stress-enduring inks. Due to synergistic effects of nanomaterial-based engineered inks and the serpentine designs, these printable bioelectronic devices endure severe mechanical deformations, e.g., stretching, indentation, or torsional twisting. Glucose and lactate BFCs with the single enzyme and membrane-free configurations generated the maximum power density of 160 and 250 µW cm^-2 with the open circuit voltages of 0.44 and 0.46 V, respectively. The textile-BFCs were able to withstand repeated severe mechanical deformations with minimal impact on its structural integrity, as was indicated from their stable power output after 100 cycles of 100% stretching. By providing power signals proportional to the sweat fuel concentration, these stretchable devices act as highly selective and stable self-powered textile sensors. Applicability to sock-based BFC and self-powered biosensor and mechanically compliant operations was demonstrated on human subjects. These stretchable skin-worn "scavenge-sense-display" devices are expected to contribute to the development of skin-worn energy harvesting systems, advanced non-invasive self-powered sensors and wearable electronics on a stretchable garment.