Bimetallic iron cobalt oxide self-supported on Ni-Foam: An efficient bifunctional electrocatalyst for oxygen and hydrogen evolution reaction

Altering electronic structure of nickel foam supported CoNi-based oxide through Al ions modulation for efficient oxygen evolution reaction

Developing highly active and durable non-precious metal-based electrocatalysts for the oxygen evolution reaction (OER) is crucial in achieving efficient energy conversion. Herein, we reported a CoNiAl0.5O/NF nanofilament that exhibits higher OER activity than previously reported IrO2-based catalysts in alkaline solution. The as-synthesized CoNiAl0.5O/NF catalyst demonstrates a low overpotential of 230 mV at a current density of 100 mA cm-2, indicating its high catalytic efficiency. Furthermore, the catalyst exhibits a Tafel slope of 26 mV dec-1, suggesting favorable reaction kinetics. The CoNiAl0.5O/NF catalyst exhibits impressive stability, ensuring its potential for practical applications. Detailed characterizations reveal that the enhanced activity of CoNiAl0.5O/NF can be attributed to the electronic modulation achieved through Al3+ incorporation, which promotes the emergence of higher-valence Ni metal, facilitating nanofilament formation and improving mass transport and charge transfer processes. The synergistic effect between nanofilaments and porous nickel foam (NF) substrate significantly enhances the electrical conductivity of this catalyst material. This study highlights the significance of electronic structures for improving the activity of cost-effective and non-precious metal-based electrocatalysts for the OER.

Crystal Structure Regulation of CoSe2 Induced by Fe Dopant for Promoted Surface Reconstitution toward Energetic Oxygen Evolution Reaction

Most nonoxide catalysts based on transition metal elements will inevitably change their primitive phases under anodic oxidation conditions in alkaline media. Establishing a relationship between the bulk phase and surface evolution is imperative to reveal the intrinsic catalytic active sites. In this work, it is demonstrated that the introduction of Fe facilitates the phase transition of orthorhombic CoSe2 into its cubic counterpart and then accelerates the Co-Fe hydroxide layer generation on the surface during electrocatalytic oxygen evolution reaction (OER). As a result, the Fe-doped cubic CoSe2 catalyst exhibits a significantly enhanced activity with a considerable overpotential decrease of 79.9 and 66.9 mV to deliver 10 mA·cm-2 accompanied by a Tafel slope of 48.0 mV·dec-1 toward OER when compared to orthorhombic CoSe2 and Fe-doped orthorhombic CoSe2, respectively. Density functional theory (DFT) calculations reveal that the introduction of Fe on the surface hydroxide layers will tune electron density around Co atoms and raise the d-band center. These findings will provide deep insights into the surface reconstitution of the OER electrocatalysts based on transition metal elements.

Effective construction of a CuCo MOF@graphene functional electrocatalyst for hydrogen evolution reaction

Electrochemical water splitting is considered a green and sustainable method of producing hydrogen energy. Herein, to pursue a highly efficient hydrogen evolution reaction, we fabricated high-performance electrocatalysts, by utilizing a bimetallic (Cu and Co) metal-organic framework to modify rGO through a one-step in situ approach. The synthesized CuCoOC@rGO presents a highly ordered structure with a defect-rich porous surface for the hydrogen evolution reaction (HER). Specifically, the appropriate adjustment of metal (Cu and Co), 1,3,5-benzenetricarboxylic acid (H3BTC), and rGO ratios leads to a well-defined morphology, which creates a defect-rich porous surface. Characterized by XRD, SEM, EDS, FT-IR spectroscopy, Raman spectroscopy, XPS, and BET, the morphology exposes more active sites, strong evidence for the promotion of electrocatalytic efficiency. Upon the analysis of the experimental data, the obtained CuCoOC@rGO catalyst exhibits excellent activity in alkaline media with a low overpotential of 120 mV at a current density of 10 mA cm-2, and a Tafel slope of 124 mV dec-1 for the hydrogen evolution reaction (HER). Guided by the structure-activity relationship, the superior HER activity of CuCoOC@rGO in alkaline electrolyte could originate from many sources, including: (1) as a self-supported substrate, CuCoOC@rGO not only leads to profitable electrical contact and mechanical stability but also firmly roots into the rGO without extra binders. (2) The highly ordered structure provides smooth ion and electron transport channels, which are conducive to electrolyte infiltration and gas release. (3) The abundance of defective pores on the surface of the nanoarrays, which offers more active sites for the catalytic process. This study provides new prospects for the rational design and fabrication of advanced hierarchical functional electrocatalysts for application in electrochemical energy devices.

Effect of carbon support on the activity of monodisperse Co45Pt55 nanoparticles for oxygen evolution in alkaline media

Oxygen evolution reaction (OER) represents the efficiency-limiting reaction in water electrolyzers, metal-air batteries, and unitized regenerative fuel cells. To achieve high-efficiency OER in alkaline media, we fabricated three novel electrocatalysts by the assembly of as-prepared Co45Pt55 alloy nanoparticles (NPs) on three different carbon-based support materials: reduced graphene oxide (CoPt/rGO), mesoporous graphitic carbon nitride (CoPt/mpg-CN), and commercial Ketjenblack carbon (CoPt/KB). Voltammetry studies revealed that CoPt/rGO electrocatalyst provided lower OER overpotentials accompanied by higher currents and specific current density values than the other two studied materials. Moreover, CoPt/rGO outperformed commercial CoPt/C electrocatalysts in terms of notably higher specific current densities. Additionally, it was found that CoPt/rGO electrocatalyst activity increases with increasing temperature up to 85°C, as suggested by the increase in the exchange current density. Electrochemical impedance spectroscopy studies of three electrocatalysts in OER revealed similar charge transfer resistance, although CoPt/rGO provided a higher current density. The main issue observed during long-term chronoamperometry and chronopotentiometry studies is the materials' instability under OER polarization conditions, which is still to be tackled in future work.

Facile synthesis of efficient Co3O4 nanostructures using the milky sap of Calotropis procera for oxygen evolution reactions and supercapacitor applications

The preparation of Co3O4 nanostructures by a green method has been rapidly increasing owing to its promising aspects, such as facileness, atom economy, low cost, scale-up synthesis, environmental friendliness, and minimal use of hazardous chemicals. In this study, we report on the synthesis of Co3O4 nanostructures using the milky sap of Calotropis procera (CP) by a low-temperature aqueous chemical growth method. The milky sap of CP-mediated Co3O4 nanostructures were investigated for oxygen evolution reactions (OERs) and supercapacitor applications. The structure and shape characterizations were done by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) techniques. The prepared Co3O4 nanostructures showed a heterogeneous morphology consisting of nanoparticles and large micro clusters. A typical cubic phase and a spinel structure of Co3O4 nanostructures were also observed. The OER result was obtained at a low overpotential of 250 mV at 10 mA cm-2 and a low Tafel slope of 53 mV dec-1. In addition, the durability of 45 hours was also found at 20 mA cm-2. The newly prepared Co3O4 nanostructures using the milky sap of CP were also used to demonstrate a high specific capacitance of 700 F g-1 at a current density of 0.8 A g-1 and a power density of 30 W h kg-1. The enhanced electrochemical performance of Co3O4 nanostructures prepared using the milky sap of CP could be attributed to the surface oxygen vacancies, a relatively high amount of Co2+, the reduction in the optical band gap and the fast charge transfer rate. These surface, structural, and optical properties were induced by reducing, capping, and stabilizing agents from the milky sap of CP. The obtained results of OERs and supercapacitor applications strongly recommend the use of the milky sap of CP for the synthesis of diverse efficient nanostructured materials in a specific application, particularly in energy conversion and storage devices.

Transforming the Electrochemical Behaviors of Cobalt Oxide from "Supercapacitator" to "Battery" by Atomic-Level Structure Engineering for Inspiring the Advance of Co-Based Batteries

Cobalt-based electrodes receive emerging attention for their high theoretical capacity and rich valence variation ability, but state-of-the-art cobalt-based electrodes present performance far below the theoretical value. Herein, the in-depth reaction mechanisms in the alkaline electrolyte are challenged and proven to be prone to the surface-redox pseudocapacitor behavior due to the low adsorption energy to OH. Using the atomic-level structure engineering strategy after substitution metal searching, the adsorption energy is effectively enhanced, and the peak of CoOOH can be observed from in situ characterization for the first time, leading to the successful transition of charge storage behavior from "supercapacitor" to "battery". When used in a Zn-Co battery as a proof of concept, it shows comprehensive electrochemical performance with a flat discharge voltage plateau of ≈1.7 V, an optimal energy density of 506 Wh kg^-1 , and a capacity retention ratio of 85.1% after 2000 cycles, shining among the reported batteries. As a practical demonstration, this battery also shows excellent self-discharge performance with the capacity retention of 90% after a 10 h delay. This work subtly tunes the intrinsic electrochemical properties of the cobalt-based material through atomic-level structure engineering, opening a new opportunity for the advance of energy storage systems.

Ultra-small-sized multi-element metal oxide nanofibers: an efficient electrocatalyst for hydrogen evolution

Compared to noble metals, transition metal oxides (TMOs) have positive development prospects in the field of electrocatalysis, and the synergy between the elements in multi-element TMO-based materials can improve their catalytic activity. However, it is still a challenge to synthesize multi-component TMO-based catalysts and deeply understand the effects of components on the catalytic performance of the catalysts. Here, we demonstrate multi-element ultra-small-sized nanofibers for efficient hydrogen production. The ternary NiFeCoO nanofiber-based electrode reached an overpotential of 82 mV at the current density of 10 mA cm^-2 with a Tafel slope of 56 mV dec^-1 in 1 M KOH, which are close to those of Pt plate (66 mV at 10 mA cm^-2; the Tafel slope is 32 mV dec^-1). In addition, the current density maintained 97% of its initial value after 10 h operation. We used the ternary NiFeCoO nanofiber-based electrode as an efficient counter electrode in photoelectrochemical hydrogen production to demonstrate the versatility of these nanofibers.

Critical Review, Recent Updates on Zeolitic Imidazolate Framework-67 (ZIF-67) and Its Derivatives for Electrochemical Water Splitting

Design and construction of low-cost electrocatalysts with high catalytic activity and long-term stability is a challenging task in the field of catalysis. Metal-organic frameworks (MOF) are promising candidates as precursor materials in the development of highly efficient electrocatalysts for energy conversion and storage applications. This review starts with a summary of basic concepts and key evaluation parameters involved in the electrochemical water-splitting reaction. Then, different synthesis approaches reported for the cobalt-based Zeolitic imidazolate framework (ZIF-67) and its derivatives are critically reviewed. Additionally, several strategies employed to enhance the electrocatalytic activity and stability of ZIF-67-based electrocatalysts are discussed in detail. The present review provides a succinct insight into the ZIF-67 and its derivatives (oxides, hydroxides, sulfides, selenides, phosphide, nitrides, telluride, heteroatom/metal-doped carbon, noble metal-supported ZIF-67 derivatives) reported for oxygen evolution reaction (OER), hydrogen evolution reaction (HER), and overall water splitting applications. Finally, this review concludes with the associated challenges and the perspectives on developing the best economic, durable electrocatalytic materials.

Island-Type Hybrid Catalysts Applied for Anion Exchange Membrane Water Electrolysis

A rapid, productive, and efficient process was invented to produce hybrid catalysts for transition metal oxide water electrolysis. The microwave-assisted hydrothermal method was applied to synthesize transition metal oxide catalysts by controlling the amount of cobalt and iron. This work solves the cracking problem for the catalytic layer during the water electrolysis. It uses Fe2O3 as the support and covers a catalytic layer outside it and a nanoscale gap between each catalyst, which can help to remove the gas and fill up the water. The unique structure of the catalysts can prevent them from accumulating gas and increasing their efficiency for long-term water electrolysis. By using unique catalysts in the water electrolyzer, the current density reaches higher than 200 mA cm−2 at 2.0 V and does not show a significant decay even after 200 h.

Electrochemically engineered zinc(iron)oxyhydroxide/zinc ferrite heterostructure with interfacial microstructure and hydrophilicity ideal for supercapacitors

Zinc ferrite@nickel foam (ZF@Nf) is a potential commercial supercapacitor electrode due to its large theoretical capacity, abundant elemental composition, excellent conductivity, and stability. However, deficient active sites limit its specific capacitance (SC). Herein, we demonstrate that engineering ZF's interfacial microstructure and hydrophilicity mitigate this limitation. ZF@Nf is used as the working electrode in a 3-electrode cell and subjected to multiple oxygen evolution reaction cycles in potassium hydroxide. Systematic changes in ZF's porosity, crystallinity, hydrophilicity, and composition after each cycle were characterised using spectroscopy, sorption isotherm, microscopy and photography techniques. During cycling, the edges of ZF partially phase-transform into a dense polycrystalline zinc(iron)oxyhydroxide film via semi-reversible oxidation resulting in zinc(iron)oxyhydroxide/ZF interface formation. The maximum ion-accessible zinc(iron)oxyhydroxide film density is obtained after 1000 cycles. Strong ionic interaction at the interface induces high hydrophilicity, this together with the 3-dimensional diffusion channels of the zinc(iron)oxyhydroxide significantly increase electroactive surface area and decrease ion diffusion resistance. Consequently, the SC, energy density, and rate-capability of the interface compare favourably with state-of-the-art electrodes. The strong interfacial interaction and polycrystallinity also ensure long-term electrochemical stability. This study proves the direct correlation between interfacial microstructure and hydrophilicity, and SC which provides a blueprint for future energy-storage electrode design.

Double-wall carbon nanotube assisted phase engineering in CoOxSy complex for efficient oxygen evolution reaction

Sluggish electron kinetics in oxygen evolution reaction (OER) is one of the main factors restricting the development of hydrogen production technology from electrical water splitting, while the key to break...

Facile synthesis of bimetallic-based CoMoO4/MoO2/CoP oxidized/phosphide nanorod arrays electroplated with FeOOH for efficient overall seawater splitting

CoMoO4/MoO2/CoP oxidized/phosphide nanorod arrays are fabricated for high performance in hydrogen evolution reaction, while the further electrodeposition of FeOOH results in excellent catalytic activity for the oxygen evolution reaction.

Microwave-Assisted vs. Conventional Hydrothermal Synthesis of MoS2 Nanosheets: Application towards Hydrogen Evolution Reaction

Molybdenum sulfide (MoS2) has emerged as a promising catalyst for hydrogen evolution applications. The synthesis method mainly employed is a conventional hydrothermal method. This method requires a longer time compared to other methods such as microwave synthesis methods. There is a lack of comparison of the two synthesis methods in terms of crystal morphology and its electrochemical activities. In this work, MoS2 nanosheets are synthesized using both hydrothermal (HT-MoS2) and advanced microwave methods (MW-MoS2), their crystal morphology, and catalytical efficiency towards hydrogen evolution reaction (HER) were compared. MoS2 nanosheet is obtained using microwave-assisted synthesis in a very short time (30 min) compared to the 24 h hydrothermal synthesis method. Both methods produce thin and aggregated nanosheets. However, the nanosheets synthesized by the microwave method have a less crumpled structure and smoother edges compared to the hydrothermal method. The as-prepared nanosheets are tested and used as a catalyst for hydrogen evolution results in nearly similar electrocatalytic performance. Experimental results showed that: HT-MoS2 displays a current density of 10 mA/cm2 at overpotential (−280 mV) compared to MW-MoS2 which requires −320 mV to produce a similar current density, suggesting that the HT-MoS2 more active towards hydrogen evolutions reaction.

Hollow Porous MnFe2 O4 Sphere Grown on Elm-Money-Derived Biochar towards Energy-Saving Full Water Electrolysis

The development of inexpensive and efficient bifunctional electrocatalysts is significant for widespread practical applications of overall water splitting technology. Herein, a one-pot solvothermal method is used to prepare hollow porous MnFe₂ O₄ spheres, which are grown on natural-abundant elm-money-derived biochar material to construct MnFe₂ O₄ /BC composite. When the overpotential is 156 mV for both the oxygen evolution reaction and the hydrogen evolution reaction, the current density reaches up to 10 mA cm^-2 , and its duration is 10 h. At 1.51 V, the overall water decomposition current density of 10 mA cm^-2 can be obtained in 1 m KOH. This work proves that elm-money-derived biochar is a valid substrate for growing hollow porous spheres. MnFe₂ O₄ /BC give a promising general strategy for preparing the effective and stable bifunctional catalysis that can be expand to multiple transition metal oxide.

Vertically stacked bilayer heterostructure CoFe2O4@Ni3S2 on a 3D nickel foam as a high-performance electrocatalyst for the oxygen evolution reaction

The as-obtained CoFe₂O₄@Ni₃S₂/NF can serve as an active and stable water oxidation catalyst under electrochemical reaction conditions.

Electrodeposition at Highly Negative Potentials of an Iron-Cobalt Oxide Catalyst for Use in Electrochemical Water Splitting

Earth-abundant transition metal-based catalysts have been extensively investigated for their applicability in water electrolysers to enable overall water splitting to produce clean hydrogen and oxygen. In this study a Fe-Co based catalyst is electrodeposited in 30 seconds under vigorous hydrogen evolution conditions to produce a high surface area material that is active for both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER). This catalyst can achieve high current densities of 600 mAcm^-2 at an applied potential of 1.6 V (vs RHE) in 1 M NaOH with a Tafel slope value of 48 mV dec^-1 for the OER. In addition, the HER can be facilitated at current densities as high as 400 mA cm^-2 due to the large surface area of the material. The materials were found to be predominantly amorphous but did contain crystalline regions of CoFe₂ O₄ which became more evident after the OER indicating interesting compositional and structural changes that occur to the catalyst after an electrocatalytic reaction. This rapid method of creating a bimetallic oxide electrode for both the HER and OER could possibly be adopted to other bimetallic oxide systems suitable for electrochemical water splitting.

Protic Imidazolium Polymer as Ion Conductor for Improved Oxygen Evolution Performance

Improving the electrocatalytic performance of oxygen evolution reaction (OER) is essential for oxygen-involved electrochemical devices, including water splitting and rechargeable metal–air batteries. In this work, we report that the OER performance of commercial catalysts of IrO₂, Co₃O₄, and Pt-C can be improved by replacing the traditional Nafion^® ionomer with newly synthesized copolymers consisting of protonated imidazolium moieties such as ion conductors and binders in electrodes. Specifically, such an improvement in OER performance for all the tested catalysts is more significant in basic and neutral environments than that under acidic conditions. We anticipate that the results will provide new ideas for the conceptual design of electrodes for oxygen-involved electrochemical devices.

Amorphous CoFe Double Hydroxides Decorated with N-Doped CNTs for Efficient Electrochemical Oxygen Evolution

The development and design of a highly active and affordable nanostructured material as an efficient electrocatalyst for electrochemical oxygen evolution is a pressing necessity to realize industrial production of hydrogen by water electrolysis. Amorphous nanocomposites have recently attracted interest owing to their superior electrocatalytic activity derived from their unique structure. Herein, amorphous CoFe double hydroxides (Am-CFDH) decorated with N-doped carbon nanotubes (NCNTs) is synthesized by a facile and simple one-pot approach under room temperature. Through electrochemical measurement, the bare Am-CFDH nanocomposite already exhibits a comparable oxygen evolution reaction (OER) activity to the commercial IrO₂ catalyst on account of its amorphous nature and the interaction between Co and Fe. The introduced NCNTs can provide better electrical conductivity, more anchoring sites, and functional groups for enhancing the transfer of electrons and reactants, preventing the agglomeration of Am-CFDH to expose more active sites, and improving the synergistic effect between Am-CFDH and NCNTs. Thus, the Am-CFDH/NCNTs hybrid displays favorable durability beyond 20 h and advanced OER activity, owning a small overpotential of 270 mV at 10 mA cm^-2 and a low Tafel slope of 56.88 mV dec^-1 in alkaline medium.

Copper-Doped Cobalt Spinel Electrocatalysts Supported on Activated Carbon for Hydrogen Evolution Reaction

The development of electrocatalysts based on the doping of copper over cobalt spinel supported on a microporous activated carbon has been studied. Both copper–cobalt and cobalt spinel nanoparticles were synthesized using a silica-template method. Hybrid materials consisting of an activated carbon (AC), cobalt oxide (Co₃O₄), and copper-doped cobalt oxide (CuCo₂O₄) nanoparticles, were obtained by dry mixing technique and evaluated as electrocatalysts in alkaline media for hydrogen evolution reaction. Physical mixtures containing 5, 10, and 20 wt.% of Co₃O₄ or CuCo₂O₄ with a highly microporous activated carbon were prepared and characterized by XRD, TEM, XPS, physical adsorption of gases, and electrochemical techniques. The electrochemical tests revealed that the electrodes containing copper as the dopant cation result in a lower overpotential and higher current density for the hydrogen evolution reaction.

Co3 O4 @Cu-Based Conductive Metal-Organic Framework Core-Shell Nanowire Electrocatalysts Enable Efficient Low-Overall-Potential Water Splitting

In the work reported herein, the electrocatalytic properties of Co₃ O₄ in hydrogen and oxygen evolution reactions have been significantly enhanced by coating a shell layer of a copper-based metal-organic framework on Co₃ O₄ porous nanowire arrays and using the products as high-performance bifunctional electrocatalysts for overall water splitting. The coating of the copper-based metal-organic framework resulted in the hybridization of the copper-embedded protective carbon shell layer with Co₃ O₄ to create a strong Cu-O-Co bonding interaction for efficient hydrogen adsorption. The hybridization also led to electronically induced oxygen defects and nitrogen doping to effectively enhance the electrical conductivity of Co₃ O₄ . The optimal as-prepared core-shell hybrid material displayed excellent overall-water-splitting catalytic activity that required overall voltages of 1.45 and 1.57 V to reach onset and a current density of 10 mA cm^-2 , respectively. This is the first report to highlight the relevance of hybridizing MOF-based co-catalysts to boost the electrocatalytic performance of nonprecious transition-metal oxides.

Ultrathin Ti3C2Tx (MXene) Nanosheet-Wrapped NiSe2 Octahedral Crystal for Enhanced Supercapacitor Performance and Synergetic Electrocatalytic Water Splitting

Metal selenides, such as NiSe₂, have exhibited great potentials as multifunctional materials for energy storage and conversation. However, the utilization of pure NiSe₂ as electrode materials is limited by its poor cycling stability, low electrical conductivity, and insufficient electrochemically active sites. To remedy these defects, herein, a novel NiSe₂/Ti₃C₂T_x hybrid with strong interfacial interaction and electrical properties is fabricated, by wrapping NiSe₂ octahedral crystal with ultrathin Ti₃C₂T_x MXene nanosheet. The NiSe₂/Ti₃C₂T_x hybrid exhibits excellent electrochemical performance, with a high specific capacitance of 531.2 F g^-1 at 1 A g^-1 for supercapacitor, low overpotential of 200 mV at 10 mA g^-1, and small Tafel slope of 37.7 mV dec^-1 for hydrogen evolution reaction (HER). Furthermore, greater cycling stabilities for NiSe₂/Ti₃C₂T_x hybrid in both supercapacitor and HER have also been achieved. These significant improvements compared with unmodified NiSe₂ should be owing to the strong interfacial interaction between NiSe₂ octahedral crystal and Ti₃C₂T_x MXene, which provides enhanced conductivity, fast charge transfer as well as abundant active sites, and highlight the promising potentials in combinations of MXene with metal selenides for multifunctional applications such as energy storage and conversion.

Cobalt-Iron Oxide Nanoarrays Supported on Carbon Fiber Paper with High Stability for Electrochemical Oxygen Evolution at Large Current Densities

Here, we demonstrate that nonprecious CoFe-based oxide nanoarrays exhibit excellent electrocatalytic activity and superior stability for electrochemical oxygen evolution reaction (OER) at large current densities (>500 mA cm^-2). Carbon fiber paper (CFP) with three-dimensional macroporous structure, excellent corrosion resistance, and high electrical properties is used as the support material to prevent surface passivation during the long-term process of OER. Through a facile method of hydrothermal synthesis and thermal treatment, vertically aligned arrays of spinel Co _xFe_{3- x}O₄ nanostructures are homogeneously grown on CFP. The morphology and the Fe-doping content of the CoFe oxide nanoarrays can be controlled by the Fe³⁺ concentration in the precursor solution. The arrays of CoFe oxide nanosheets (NSs) grown on CFP (Co_2.3Fe_0.7O₄-NSs/CFP) deliver lower Tafel slope (34.3 mV dec^-1) than CoFe oxide nanowire (NW) arrays grown on CFP (Co_2.7Fe_0.3O₄-NWs/CFP) in alkaline solution, owing to higher Fe-doping content and larger effective specific surface area. The Co_2.3Fe_0.7O₄-NSs/CFP electrode exhibits excellent stability for OER at large current densities in alkaline solution. Moreover, the morphology and structure of CoFeO nanoarrays are well preserved after long-term testing, indicating the high stability for OER.

Doping β-CoMoO4 Nanoplates with Phosphorus for Efficient Hydrogen Evolution Reaction in Alkaline Media

Mass production of hydrogen by electrolysis of water largely hinges on the development of highly efficient and economical electrocatalysts for hydrogen evolution reaction (HER). Though having the merits of high earth abundance, easy availability, and tunable composition, transition-metal oxides are usually deemed as poor electrocatalysts for HER. Herein, we demonstrate that doping β-CoMoO₄ nanoplates with phosphorus can turn them into active electrocatalysts for HER. Theoretical calculation and experimental studies unravel that enhanced electrical conductivity and optimized hydrogen adsorption free energy are major causes for the improvement of intrinsic activity. As a result, only an overpotential of 138 mV is required to drive hydrogen evolving at a current density of 10 mA cm^-2 in 1 M KOH for P-doped β-CoMoO₄, which outstrips many recently reported transition-metal oxides and is just slightly inferior to commercial Pt/C. This work opens a new route to tune the HER performance of transition-metal oxides.

Cobalt Sulfide/Nickel Sulfide Heterostructure Directly Grown on Nickel Foam: An Efficient and Durable Electrocatalyst for Overall Water Splitting Application

Fabrication of high-performance noble-metal-free bifunctional electrocatalysts for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in water is a promising strategy toward future carbon-neutral economy. Herein, a one-pot hydrothermal synthesis of cobalt sulfide/nickel sulfide heterostructure supported by nickel foam (CoS _x/Ni₃S₂@NF) was performed. The Ni foam acted as the three-dimensional conducting substrate as well as the source of nickel for Ni₃S₂. The formation of CoS _x/Ni₃S₂@NF was confirmed by X-ray diffraction and X-ray photoelectron spectroscopy. The formation of CoS _x/Ni₃S₂@NF facilitated easy charge transport and showed synergistic electrocatalytic effect toward HER, OER, and overall water splitting in alkaline medium. Remarkably, CoS _x/Ni₃S₂@NF showed catalytic activity comparable with that of benchmarking electrocatalysts Pt/C and RuO₂. For CoS _x/Ni₃S₂@NF, overpotentials of 204 and 280 mV were required to achieve current densities of 10 and 20 mA cm^-2 for HER and OER, respectively, in 1.0 M KOH solution. A two-electrode system was formulated for overall water splitting reaction, which showed current densities of 10 and 50 mA cm^-2 at 1.572 and 1.684 V, respectively. The prepared catalyst exhibited excellent durability in HER and OER catalyzing conditions and also in overall water splitting operation. Therefore, CoS _x/Ni₃S₂@NF could be a promising noble-metal-free electrocatalyst for overall water splitting application.

Molybdenum Carbide-Decorated Metallic Cobalt@Nitrogen-Doped Carbon Polyhedrons for Enhanced Electrocatalytic Hydrogen Evolution

Electrocatalytic hydrogen evolution reaction (HER) based on water splitting holds great promise for clean energy technologies, in which the key issue is exploring cost-effective materials to replace noble metal catalysts. Here, a sequential chemical etching and pyrolysis strategy are developed to prepare molybdenum carbide-decorated metallic cobalt@nitrogen-doped porous carbon polyhedrons (denoted as Mo/Co@N-C) hybrids for enhanced electrocatalytic hydrogen evolution. The obtained metallic Co nanoparticles are coated by N-doped carbon thin layers while the formed molybdenum carbide nanoparticles are well-dispersed in the whole Co@N-C frames. Benefiting from the additionally implanted molybdenum carbide active sites, the HER performance of Mo/Co@N-C hybrids is significantly promoted compared with the single Co@N-C that is derived from the pristine ZIF-67 both in alkaline and acidic media. As a result, the as-synthesized Mo/Co@N-C hybrids exhibit superior HER electrocatalytic activity, and only very low overpotentials of 157 and 187 mV are needed at 10 mA cm^-2 in 1 m KOH and 0.5 m H₂ SO₄ , respectively, opening a door for rational design and fabrication of novel low-cost electrocatalysts with hierarchical structures toward electrochemical energy storage and conversion.

Green Synthesis of CoFe2O4 and Investigation of its Catalytic Efficiency for Degradation of Dyes in Aqueous Medium

The catalytic wet oxidation is one the methods used for elimination of dyes from aqueous medium in which various metal based materials can be used as heterogeneous catalysts. Bimetallic oxides as heterogeneous catalysts have gained much attention as bimetallization improve the catalytic properties of the resulting particles. The biosynthetic green method is the most viable and simple method for synthesis of bimetallic oxides nanoparticles. Here, we report the green synthesis of CoFe2O4 particles using Azadirachata indica leaves extract as reducing and stabilizing agent. The synthesized particles were characterized using X-ray diffraction, thermogravimetric analysis, Fourier-transform infrared spectroscopy and scanning electron microscopy. The synthesized CoFe2O4 particles were tested as a catalyst for mineralization of rhodamine B and methylene blue dyes in the presence of hydrogen peroxide in aqueous media. More than 95% dyes degraded in 120 min. The reaction kinetics was described in terms of Langmuir–Hinshelwood mechanism which suggests that molecules of dye and hydrogen peroxide adsorbed surface of CoFe2O4 and then react together.