Electrochemical detection of nitrite at NiFe2O4 nanoparticles synthesised by solvent deficient method

Ag-CeO2 Based on Electrochemical Sensor for High-Efficient On-Site Detection of Nitrite in Aquaculture Water and Beverages

Nitrite is one of the most common nitrogenous compounds, which is not only an important indicator of aquaculture water but also widely used as a food additive. Its potential toxicity poses a huge threat to aquatic products and human health. Therefore, it is important to develop a convenient and rapid sensor for the high-efficient onsite detection of nitrite. In this work, a novel electrochemical sensor was developed for the qualitative and quantitative analysis of nitrite. The developed nitrite electrochemical detection system is easily applied in onsite detection. The electrochemical working electrode was constructed based on the combination of Ag-CeO2 and conductive carbon paste (CPE) with excellent electrocatalysis activity and rapid electron transfer ability. By the application of the developed system and under the optimal conditions, the linear range was from 40.0 μM to 500.0 μM, and the detection limit was reduced to 4.3 μM. The recovery was between 92.1% and 108.1%, and the relative standard deviations (RSDs) were 0.49%~9.31%. The sensor exhibited superior reproducibility, high stability sensitivity, and anti-interference ability, confirming its effectiveness for nitrite analysis. Finally, the developed electrochemical sensor was successfully applied to detect nitrite in beverages and aquaculture water samples, indicating that this approach has great potential in onsite food testing and environmental monitoring.

Nonmetal catalyst boosting amplification of both colorimetric and electrochemical signal for multi-mode nitrite sensing

Recently, nanozymes as an outstanding alternative to natural enzymes has attracted wide attention because of its high stability performance. In this study, PNC nonmetal nanozymes with high oxidase-like activity was synthesized can specifically catalyze colorless 3,3,5,5-tetramethyl-benzidine(TMB) to form blue oxidized TMB (TMBox). In the presence of nitrite, it further oxidizes TMBox to obtain yellow derivative products attributed to nitrite inducing diazotization reaction in TMBox. Based on this principle, a colorimetric and electrochemical sensing system was developed, and the ultra-sensitive multi-mode detection of nitrite was realized by combining RGB mode of smart phone, UV-Vis spectrum and electrochemical method. Compared with single signal detection, the multi-mode sensing system can realize self-validation to achieve more reliable detection results. What's more, the developed multi-mode sensing could quickly and sensitively detect nitrite in real sample, especially RGB mode of smart phone meeting the equipment limited areas, suggesting a broad application prospects in food safety.

MnCo2O4 Spinel Nanorods for Highly Sensitive Electrochemical Detection of Nitrite

The rational design of nitrite sensors has attracted significant research interest due to their widespread use and the associated risks of methemoglobinemia and carcinogenicity. The undisclosed nitrite-sensing performance of the spinel cobaltite MnCo2O4 (MCO) prepared by an oxalate-assisted coprecipitation method is reported in this study. Spectroscopy and microscopy investigations revealed the formation of uniform MCO nanorods with a high aspect ratio. The electrocatalytic nitrite oxidation at the MCO-coated glassy carbon electrode (MCO/GCE) indicated the promising performance of the synthesized material for nitrite sensing. MCO/GCE detects nitrite in a concentration range of 5 μM to 3 mM and has a limit of detection of 0.95 μM with a higher sensitivity of 857 μA mM-1 cm-2 in a response time of 4 s. In MCO, the mixed-valence states of Co2+/Co3+ confer a high electrical conductivity, and higher valent redox couples of Mn and Co impart remarkable electrocatalytic activity toward nitrite oxidation. MCO spinel undergoes facile and ultrafast faradaic reactions to mediate nitrite oxidation. Additionally, the mesopores of MCO nanorods facilitate the rapid diffusion of electrolyte and nitrite ions. Employing the electrode in sensing nitrite in milk, lake, and tap water samples further validates its potential application in real-life testing. MCO spinel nanorods showcase promising scope for utilization in the electrochemical sensing of nitrite and inspire further exploration of transition-metal oxide-based mixed-spinel materials.

Ti3C2 Nanosheets Functionalized with Ferritin-Biomimetic Platinum Nanoparticles for Electrochemical Biosensors of Nitrite

Nitrites widely exist in human life and the natural environment, but excessive contents of nitrites will result in adverse effects on the environment and human health; hence, sensitive and stable nitrite detection systems are needed. In this study, we report the synthesis of Ti3C2 nanosheets functionalized with apoferritin (ApoF)-biomimetic platinum (Pt) nanoparticle (Pt@ApoF/Ti3C2) composite materials, which were formed by using ApoF as a template and protein-inspired biomineralization. The formed nanohybrid exhibits excellent electrochemical sensing performance towards nitrite (NaNO2). Specifically, the Pt@ApoF catalyzes the conversion of nitrites into nitrates, converting the chemical signal into an electrical signal. The prepared Pt@ApoF/Ti3C2-based electrochemical NaNO2 biosensors demonstrate a wide detection range of 0.001-9 mM with a low detection limit of 0.425 μM. Additionally, the biosensors possess high selectivity and sensitivity while maintaining a relatively stable electrochemical sensing performance within 7 days, enabling the monitoring of NaNO2 in complex environments. The successful preparation of the Pt@ApoF/Ti3C2 nanohybrid materials provides a new approach for constructing efficient electrochemical biosensors, offering a simple and rapid method for detecting NaNO2 in complex environments.

Phosphorus-doped synergy of phase change in heterogeneous catalysts of NiS-NiS2 for efficient electrocatalysis of Pb(II)

A fundamental understanding of the electroanalytical activity of transition metal sulfide electrocatalysts, especially the origin of the electrocatalytic reactivity on the surface sites of heterostructures with multiple crystalline phases, is essential for the design of low-cost and highly efficient nonprecious metal electrocatalysts for further scientific and technological achievements. Herein, we injected P into NiS and occupied the S sites through a doping strategy. The redistributed electronic structure induced the construction of heterostructures, which significantly improved the structure and chemical state of electrochemically inert NiS. The phase-change mechanism between NiS and NiS2 synergistically catalyzes Pb(II), while the P and S sites jointly lose electrons. Moreover, the constructed heterojunction sensor shows the a sensitivity of 83.43 μA μM-1 to Pb(II) with a theoretical limit of detection of 48 nM, as well as excellent stability, reproducibility, and anti-interference ability. The accurate detection in real water further reveals the potential of this sensor for practical applications. This study provides a guiding strategy for improving electrochemically inert materials to design highly active electrocatalytic interfaces, which has important implications for the development of highly efficient electrode-sensitive materials similar to precious metals to achieve accurate electrical analysis.

Electrochemical Sensors Based on Transition Metal Materials for Phenolic Compound Detection

Electrochemical sensors have been recognized as crucial tools for monitoring comprehensive chemical information, especially in the detection of a significant class of molecules known as phenolic compounds. These compounds can be present in water as hazardous analytes and trace contaminants, as well as in living organisms where they regulate their metabolism. The sensitive detection of phenolic compounds requires highly efficient and cost-effective electrocatalysts to enable the development of high-performance sensors. Therefore, this review focuses on the development of advanced materials with excellent catalytic activity as alternative electrocatalysts to conventional ones, with a specific emphasis on transition metal-based electrocatalysts for the detection of phenolic compounds. This research is particularly relevant in diverse sectors such as water quality, food safety, and healthcare.

Investigations of Structural, Magnetic, and Electrochemical Properties of NiFe2O4 Nanoparticles as Electrode Materials for Supercapacitor Applications

Magnetic nanoparticles of NiFe₂O₄ were successfully prepared by utilizing the sol-gel techniques. The prepared samples were investigated through various techniques such as X-ray diffraction (XRD), transmission electron microscopy (TEM), dielectric spectroscopy, DC magnetization and electrochemical measurements. XRD data analysed using Rietveld refinement procedure inferred that NiFe₂O₄ nanoparticles displayed a single-phase nature with face-centred cubic crystallinity with space group Fd-3m. Average crystallite size estimated using the XRD patterns was observed to be ~10 nm. The ring pattern observed in the selected area electron diffraction pattern (SAED) also confirmed the single-phase formation in NiFe₂O₄ nanoparticles. TEM micrographs confirmed the uniformly distributed nanoparticles with spherical shape and an average particle size of 9.7 nm. Raman spectroscopy showed characteristic bands corresponding to NiFe₂O₄ with a shift of the A_1g mode, which may be due to possible development of oxygen vacancies. Dielectric constant, measured at different temperatures, increased with temperature and decreased with increase in frequency at all temperatures. The Havrilliak-Negami model used to study the dielectric spectroscopy indicated that a NiFe₂O₄ nanoparticles display non-Debye type relaxation. Jonscher's power law was utilized for the calculation of the exponent and DC conductivity. The exponent values clearly demonstrated the non-ohmic behaviour of NiFe₂O₄ nanoparticles. The dielectric constant of the nanoparticles was found to be >300, showing a normal dispersive behaviour. AC conductivity showed an increase with the rise in temperature with the highest value of 3.4 × 10^-9 S/cm at 323 K. The M-H curves revealed the ferromagnetic behaviour of a NiFe₂O₄ nanoparticle. The ZFC and FC studies suggested a blocking temperature of ~64 K. The saturation of magnetization determined using the law of approach to saturation was ~61.4 emu/g at 10 K, corresponding to the magnetic anisotropy ~2.9 × 10⁴ erg/cm³. Electrochemical studies showed that a specific capacitance of ~600 F g^-1 was observed from the cyclic voltammetry and galvanostatic charge-discharge, which suggested its utilization as a potential electrode for supercapacitor applications.

Bismuth-Decorated Honeycomb-like Carbon Nanofibers: An Active Electrocatalyst for the Construction of a Sensitive Nitrite Sensor

The existence of carcinogenic nitrites in food and the natural environment has attracted much attention. Therefore, it is still urgent and necessary to develop nitrite sensors with higher sensitivity and selectivity and expand their applications in daily life to protect human health and environmental safety. Herein, one-dimensional honeycomb-like carbon nanofibers (HCNFs) were synthesized with electrospun technology, and their specific structure enabled controlled growth and highly dispersed bismuth nanoparticles (Bi NPs) on their surface, which endowed the obtained Bi/HCNFs with excellent electrocatalytic activity towards nitrite oxidation. By modifying Bi/HCNFs on the screen-printed electrode, the constructed Bi/HCNFs electrode (Bi/HCNFs-SPE) can be used for nitrite detection in one drop of solution, and exhibits higher sensitivity (1269.9 μA mM^-1 cm^-2) in a wide range of 0.1~800 μM with a lower detection limit (19 nM). Impressively, the Bi/HCNFs-SPE has been successfully used for nitrite detection in food and environment samples, and the satisfactory properties and recovery indicate its feasibility for further practical applications.

Towards Embedded Electrochemical Sensors for On-Site Nitrite Detection by Gold Nanoparticles Modified Screen Printed Carbon Electrodes

The transition of electrochemical sensors from lab-based measurements to real-time analysis requires special attention to different aspects in addition to the classical development of new sensing materials. Several critical challenges need to be addressed including a reproducible fabrication procedure, stability, lifetime, and development of cost-effective sensor electronics. In this paper, we address these aspects exemplarily for a nitrite sensor. An electrochemical sensor has been developed using one-step electrodeposited (Ed) gold nanoparticles (EdAu) for the detection of nitrite in water, which shows a low limit of detection of 0.38 µM and excellent analytical capabilities in groundwater. Experimental investigations with 10 realized sensors show a very high reproducibility enabling mass production. A comprehensive investigation of the sensor drift by calendar and cyclic aging was carried out for 160 cycles to assess the stability of the electrodes. Electrochemical impedance spectroscopy (EIS) shows significant changes with increasing aging inferring the deterioration of the electrode surface. To enable on-site measurements outside the laboratory, a compact and cost-effective wireless potentiostat combining cyclic and square wave voltammetry, and EIS capabilities has been designed and validated. The implemented methodology in this study builds a basis for the development of further on-site distributed electrochemical sensor networks.

Multilayer Heterogeneous Membrane Biosensor Based on Multiphysical Field Coupling for Human Serum Albumin Detection

A factor closely associated with renal disease status in clinical diagnosis is abnormal human serum albumin (HSA) concentration levels in human body fluids urine, serum, etc. The surface stress biosensor was developed as a new type of biosensor to detect protein molecule concentration and has a wide range of clinical applications. However, further sensitivity improvement is required to achieve higher detection performance. Herein, MXene/PDMS/Fe₃O₄/PDMS of the multilayer heterogeneous membrane biosensor (MHBios) based on the coupling of the magnetic field, electric field, and surface stress field was successfully developed to achieve high sensitivity HSA detection through magnetic sensitization. The modified antibody specifically binds to HSA at the AuNP layer, allowing the biosensor to convert the surface stress caused by PDMS film deformation into an electrical signal. When the biosensor was exposed to a uniform magnetic field, the conductive path of the conductive layer was reshaped further as the magnetic force amplified the deformation of the PDMS film, enhancing the conversion of biological signals to electrical signals. The results exhibited that the detection limit (LOD) of the MHBios was 78 ng/mL when HSA concentration was 0-50 μg/mL, which was markedly lower than the minimum diagnostic limit of microalbuminuria. Furthermore, the MHBios detected HSA in actual samples, confirming the potential for early disease screening.

A molybdenum disulfide/nickel ferrite-modified voltammetric sensing platform for ultra-sensitive determination of clenbuterol under the presence of an external magnetic field†

The electrochemical behavior and sensing performance of an electrode modified with NiFe₂O₄ (NFO), MoS₂, and MoS₂–NFO were thoroughly investigated using CV, EIS, DPV, and CA measurements, respectively. MoS₂–NFO/SPE provided a higher sensing performance towards the detection of clenbuterol (CLB) than other proposed electrodes. After optimization of pH and accumulation time, the current response recorded at MoS₂–NFO/SPE linearly increased with an increase of CLB concentration in the range from 1 to 50 μM, corresponding to a LOD of 0.471 μM. In the presence of an external magnetic field, there were positive impacts not only on mass transfer, ionic/charge diffusion, and absorption capacity but also on the electrocatalytic ability for redox reactions of CLB. As a result, the linear range was widened to 0.5–50 μM and the LOD value was about 0.161 μM. Furthermore, stability, repeatability, and selectivity were assessed, emphasizing their high practical applicability.

The electrochemical behavior and sensing performance of an electrode modified with NiFe₂O₄ (NFO), MoS₂, and MoS₂–NFO were thoroughly investigated using CV, EIS, DPV, and CA measurements, respectively.

Preparation of highly sensitive electrochemical sensor for detection of nitrite in drinking water samples

Nitrite is both an environmental contaminant and a food additive. Excessive intake of nitrites not only causes blood diseases, but also has the potential risk of causing cancer. Therefore, rapid detection of nitrite in water is necessary. In this work, we propose an electrochemical sensor for the sensing of nitrite. Glassy carbon electrodes modified with noble metal nanomaterials have been widely used in the preparation of sensors, but the surface properties of noble metals largely affect the sensing performance. This work proposes the biosynthesis of Au nanoparticles using the pollen extract of Lycoris radiata as a reducing agent. Flavonoids rich in pollen can be used as weak reducing agents for the reduction of chloroauric acid, and slowly synthesize uniformly dispersed Au nanoparticles. These Au nanoparticles do not agglomerate because they contain small biological molecules on the surface and can form a homogeneous sensing interface on the electrode surface. The electrochemical sensor assembled with biosynthesized Au nanoparticles provides linear detection of nitrite between 0.01 and 3.8 mM. The sensor also has excellent immunity to interference. In addition, the proposed sensor was also successfully used for the detection of nitrite in drinking water.

SiO2/Al2O3/C grafted 3-n propylpyridinium silsesquioxane chloride-based non-enzymatic electrochemical sensor for determination of carcinogenic nitrite in food products

The excessive uptake of nitrite is perilous and detrimental for human health that prone to cancer disease. Herein, described the synthesis of SiO₂/Al₂O₃/C material through the sol-gel procedure followed by grafting with 3-n propylpyridinium silsesquioxane chloride organic ligand for enhancing electrochemical activity. H-NMR, ¹³C NMR, and ²⁹Si studies were performed for confirmation of surface functionalization through the grafting technique. The surface morphology was evaluated through SEM and TEM techniques. The material showed an irregular and flakes-like structure that exhibited more compactness and conglomerate structure with no segregation in phase was observed after grafting. The elemental composition was confirmed from EDX analysis. The electrochemical measurements were performed with cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and chronoamperometry. The prepared hybrid inorganic-organic composite Si/C/Al/SiPy⁺Cl^- was applied for the modification of the glassy carbon (GC) electrode and assessed as a sensor for nitrite determination. The sensor showed the low limit of detection (0.01 μM), low limit of quantification (0.08 μM), wide linear response range (0.2-280 μM), and high sensitivity (410 μA·μM^-1). It gave a quick response time of <1 s in the presence of 70 μM nitrite. The fabricated sensor showed high sensitivity, chemical stability, and insignificant interference from co-existing species present in sausage meat and food industry discharges. The repeatability of the sensor was evaluated as 2.5 % R.S.D.; for n = 10 at 50 μM nitrite.

Pd-Cu nanospheres supported on Mo2C for the electrochemical sensing of nitrites

The improper disposal in agricultural and industrial wastewater leads to high NO₂^- concentrations in the aquatic environment, which can cause cancer in humans and animals; thus, their quick and accurate detection is urgently needed to ensure public health and environmental safety. In this study, a reliable and selective electrochemical sensor consisting of Pd-Cu nanospheres (NSs) supported on molybdenum carbide was prepared via simple ultrasonication. Then, a glassy carbon electrode was realized using this composite (Pd-Cu-Mo₂C-modified GCE) to test its electrocatalytic sensing for NO₂^- in a 0.1 M phosphate-buffered solution (PBS) solution via cyclic voltammetry and amperometry; at a low oxidation potential, the anodic peak current of NO₂^- detected by this electrode was significantly higher than that of its unmodified and other modified electrodes. The sensor showed a broad linear response in the 5-165-nM NO₂^- concentration range, with a low detection limit (0.35 nM in 0.1 M PBS) and high sensitivity (3.308 μAnM^-1 cm^-2). Moreover, the fabricated electrode was successfully applied for detecting nitrites in sausages, river water, and milk, showing also good recovery.

Magnetic nanomaterials based electrochemical (bio)sensors for food analysis

It is widely accepted that nanotechnology attracted more interest because of various values that nanomaterial applications offers in different fields. Recently, researchers have proposed nanomaterials based electrochemical sensors and biosensors as one of the potent alternatives or supplementary analytical tools to the conventional detection procedures that consumes a lot of time. Among different nanomaterials, researchers largely considered magnetic nanomaterials (MNMs) for developing and fabricating the electrochemical (bio)sensors for numerous utilizations. Among several factors, healthier and higher quality foods are the most important preferences of consumers and manufacturers. For this reason, developing new techniques for rapid, precise as well as sensitive determination of components or contaminants of foods is very important. Therefore, developing the new electrochemical (bio)sensors in food analysis is one of the key and effervescent research fields. In this review, firstly, we presented the properties and synthesis strategies of MNMs. Then, we summarized some of the recently developed MNMs-based electrochemical (bio)sensors for food analysis including detecting the antioxidants, synthetic food colorants, pesticides, heavy metal ions, antibiotics and other analytes (bisphenol A, nitrite and aflatoxins) from 2010 to 2020. Finally, the present review described advantages, challenges as well as future directions in this field.

Gold nanoparticles decorated bimetallic CuNi-based hollow nanoarchitecture for the enhancement of electrochemical sensing performance of nitrite

Gold nanoparticles (AuNPs) decorated bimetallic CuNi-based hollow nanoarchitecture (CNHN) are reported for the first time as a nonenzymatic sensor for the quantification of nitrite in neutral solution . The CNHN was prepared via a convenient calcining routine using the bimetallic CuNi-MOFs as a coprecursor. The unique chemical structure of hollow CNHN with high specific surface area and abundant terminal amino groups effectively avoid the aggregation of AuNPs and facilitate the subsequent adsorption of nitrite. The Au/CNHN exhibited high electrocatalytic activity towards nitrite oxidation due to the synergetic catalytic effect of AuNPs and CNHN. Chronoamperometric detection of nitrite at the Au/CNHN/GCE achieved a lower linear calibration range of 0.05 to 1.15 mM, with an LOD of 0.017 μM compared with previous reports. The proposed method obtained satisfactory recoveries for nitrite determination in practical applications, which was verified by UV-Vis spectrophotometry. The prepared sensor based on Au/CNHN featured favorable selectivity and stability, which provides a promising approach for real sample analysis. Graphical abstract.

A Novel NiFe2O4/Paper-Based Magnetoelastic Biosensor to Detect Human Serum Albumin

For the first time, a novel NiFe2O4/paper-based magnetoelastic (ME) biosensor was developed for rapid, sensitive, and portable detection of human serum albumin (HSA). Due to the uniquely magnetoelastic effect of NiFe2O4 nanoparticles and the excellent mechanical properties of the paper, the paper-based ME biosensor transforms the surface stress signal induced by the specific binding of HSA and antibody modified on the paper into the electromagnetic signal. The accumulated binding complex generates a compressive stress on the biosensor surface, resulting in a decrease in the biosensor's static magnetic permeability, which correlates to the HSA concentrations. To improve the sensitivity of the biosensor, the concentration of NiFe2O4 nanofluid and the impregnated numbers of the NiFe2O4 nanofluid-impregnated papers were optimized. The experimental results demonstrated that the biosensor exhibited a linear response to HSA concentrations ranging from 10 μg∙mL-1 to 200 μg∙mL-1, with a detection limit of 0.43 μg∙mL-1, which is significantly lower than the minimal diagnosis limit of microalbuminuria. The NiFe2O4/paper-based ME biosensor is easy to fabricate, and allows the rapid, highly-sensitive, and selective detection of HSA, providing a valuable analytical device for early monitoring and clinical diagnosis of microalbuminuria and nephropathy. This study shows the successful integration of the paper-based biosensor and the ME sensing analytical method will be a highly-sensitive, easy-to-use, disposable, and portable alternative for point-of-care monitoring.

Film Carbon Veil-Based Electrode Modified with Triton X-100 for Nitrite Determination

A film carbon veil-based electrode (FCVE) modified with non-ionic surfactant Triton X-100 (TrX100) has been developed for nitrite determination. A new simple and producible technique of hot lamination (heat sealing) has been used for the FCVE manufacturing. The paper presents the findings of investigating the FCVE and the TrX100/FCVE by using voltammetry, chronoamperometry, and scanning electron microscopy. Modification of the electrode with TrX100 improves the hydrophilic property of its surface, which results in a larger electrode active area and higher sensitivity. Optimal conditions for nitrite determination with the use of the TrX100/FCVE have been identified. The linear range (LR) and the limit of detection (LOD) are 0.1–100 μM and 0.01 μM, respectively. The relative standard deviation (RSD) does not exceed 2.3%. High selectivity of the sensor ensures its successful application for the analysis of real samples (sausage products and natural water). The obtained results accord well with the results of the standard spectrophotometric method.

A facile chemical synthesis of CuxNi(1-x)Fe2O4 nanoparticles as a nonprecious ferrite material for electrocatalytic oxidation of acetaldehyde

In the present work, Cu-doped nickel ferrite (CuxNi(1-x)Fe2O4) nanoparticles (CuNFNPs) were chemically fabricated by adding citric acid as a capping agent followed by combustion and calcination for acetaldehyde oxidation reaction (AOR) in KOH electrolytes. The as-prepared CuNFNPs were studied in terms of Fourier-transform infrared spectroscopy (FT-IR), Transmission electron microscopy (TEM), Field emission scanning electron microscope (FE-SEM), Energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) specific surface area analyses. The morphology of CuNFNPs has sponges-structure containing irregular pores. Additionally, XRD analysis indicated that the prepared CuNFNPs have a cubic-crystals ferrite without the existence of impurities and the crystal size around 20.2 nm. The electrooxidation of acetaldehyde by the presented CuNFNPs was investigated using cyclic voltammetry (CV), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS) in -OH media. Furthermore, the effects of -OH and acetaldehyde on the electrocatalytic performance were studied with and without Cu-doping in addition to EIS and CA studies which confirm the high-performance of CuNFNPs as an electrocatalyst for AOR.

Facile Synthesis of ZnMn2O4@rGO Microspheres for Ultrasensitive Electrochemical Detection of Hydrogen Peroxide from Human Breast Cancer Cells

Mixed transition-metal oxides have witnessed increasing attention in catalysts and electrocatalysts. Herein, reduced graphene oxide-wrapped ZnMn₂O₄ microspheres (ZnMn₂O₄@rGO) were facilely synthesized through the solvothermal technique. The microstructure and morphology of ZnMn₂O₄@rGO microspheres were analyzed under Raman, X-ray photoelectron, X-ray diffraction, and energy-dispersive spectroscopies and scanning electron microscopy. The synthesized ZnMn₂O₄@rGO was employed as an excellent electrocatalyst for the reduction of hydrogen peroxide (H₂O₂). The ZnMn₂O₄@rGO-modified glassy carbon electrode (ZnMn₂O₄@rGO/GCE) exhibited a linear detection to H₂O₂ in a wide concentration range of 0.03-6000 μM with a detection limit of 0.012 μM. The biosensor was evaluated to determine H₂O₂ secreted by human breast cancer cells (MCF-7), indicating its promising applications in physiology and diagnosis.